[PATCH v15 0/3] mt8183 dpi support pin mode swap

[PATCH v15 0/3] mt8183 dpi support pin mode swap

[Jitao Shi]

Changes since v14:
 - add "Acked-by" and "Reviewed-by"
 - change port@0 to port in yaml

Changes since v13:
 - move dpi dual edge patches to another series because it will have long time
   to implement the dual edge change base boris patches.
   https://patchwork.kernel.org/cover/11354279/

Changes since v12:
 - fix mediatek,dpi.yaml make_dt_binding_check errors.

Change since v11:
 - fine tune mediatek,dpi.yaml.
 - add Acked-by: Rob Herring <robh@kernel.org>.

Change since v10:
 - convert the Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
   to yaml format.
 - read the pclk-sample in endpoint.

Changes since v9:
 - rename pinctrl-names = "gpiomode", "dpimode" to "active", "idle".
 - fix some typo.

Changes since v8:
 - drop pclk-sample redefine in mediatek,dpi.txt
 - only get the gpiomode and dpimode when dpi->pinctrl is successful.

Changes since v7:
 - separate dt-bindings to independent patches.
 - move dpi dual edge to one patch.

Changes since v6:
 - change dual_edge to pclk-sample
 - remove dpi_pin_mode_swap and

Changes since v5:
 - fine tune the dt-bindings commit message.

Changes since v4:
 - move pin mode control and dual edge control to deveice tree.
 - update dt-bindings document for pin mode swap and dual edge control.

Changes since v3:
 - add dpi pin mode control when dpi on or off.
 - update dpi dual edge comment.

Changes since v2:
 - update dt-bindings document for mt8183 dpi.
 - separate dual edge modfication as independent patch.

Jitao Shi (3):
  dt-bindings: display: mediatek: control dpi pins mode to avoid leakage
  dt-bindings: display: mediatek: convert the document format from txt
    to yaml
  drm/mediatek: set dpi pin mode to gpio low to avoid leakage current

 .../bindings/display/mediatek/mediatek,dpi.txt     | 36 --------
 .../bindings/display/mediatek/mediatek,dpi.yaml    | 97 ++++++++++++++++++++++
 drivers/gpu/drm/mediatek/mtk_dpi.c                 | 31 +++++++
 3 files changed, 128 insertions(+), 36 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
 create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml

-- 
2.12.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v15 1/3] dt-bindings: display: mediatek: control dpi pins mode to avoid leakage

[Jitao Shi]

Add property "pinctrl-names" to swap pin mode between gpio and dpi mode. Set
the dpi pins to gpio mode and output-low to avoid leakage current when dpi
disabled.

Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
index 58914cf681b8..77def4456706 100644
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
@@ -17,6 +17,9 @@ Required properties:
   Documentation/devicetree/bindings/graph.txt. This port should be connected
   to the input port of an attached HDMI or LVDS encoder chip.
 
+Optional properties:
+- pinctrl-names: Contain "default" and "sleep".
+
 Example:
 
 dpi0: dpi@1401d000 {
@@ -27,6 +30,9 @@ dpi0: dpi@1401d000 {
 		 <&mmsys CLK_MM_DPI_ENGINE>,
 		 <&apmixedsys CLK_APMIXED_TVDPLL>;
 	clock-names = "pixel", "engine", "pll";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dpi_pin_func>;
+	pinctrl-1 = <&dpi_pin_idle>;
 
 	port {
 		dpi0_out: endpoint {
-- 
2.12.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v15 1/3] dt-bindings: display: mediatek: control dpi pins mode to avoid leakage

[Chun-Kuang Hu]

Hi, Jitao:

Jitao Shi <jitao.shi@mediatek.com> 於 2020年4月15日 週三 上午9:13寫道：
>
> Add property "pinctrl-names" to swap pin mode between gpio and dpi mode. Set
> the dpi pins to gpio mode and output-low to avoid leakage current when dpi
> disabled.

Applied to mediatek-drm-next [1], thanks.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux.git/log/?h=mediatek-drm-next

Regards,
Chun-Kuang.

>
> Acked-by: Rob Herring <robh@kernel.org>
> Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt | 6 ++++++
>  1 file changed, 6 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> index 58914cf681b8..77def4456706 100644
> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> @@ -17,6 +17,9 @@ Required properties:
>    Documentation/devicetree/bindings/graph.txt. This port should be connected
>    to the input port of an attached HDMI or LVDS encoder chip.
>
> +Optional properties:
> +- pinctrl-names: Contain "default" and "sleep".
> +
>  Example:
>
>  dpi0: dpi@1401d000 {
> @@ -27,6 +30,9 @@ dpi0: dpi@1401d000 {
>                  <&mmsys CLK_MM_DPI_ENGINE>,
>                  <&apmixedsys CLK_APMIXED_TVDPLL>;
>         clock-names = "pixel", "engine", "pll";
> +       pinctrl-names = "default", "sleep";
> +       pinctrl-0 = <&dpi_pin_func>;
> +       pinctrl-1 = <&dpi_pin_idle>;
>
>         port {
>                 dpi0_out: endpoint {
> --
> 2.12.5
> _______________________________________________
> Linux-mediatek mailing list
> Linux-mediatek@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-mediatek

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v15 2/3] dt-bindings: display: mediatek: convert the document format from txt to yaml

[Jitao Shi]

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 .../bindings/display/mediatek/mediatek,dpi.txt     | 42 ----------
 .../bindings/display/mediatek/mediatek,dpi.yaml    | 97 ++++++++++++++++++++++
 2 files changed, 97 insertions(+), 42 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
 create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml

diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
deleted file mode 100644
index 77def4456706..000000000000
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
+++ /dev/null
@@ -1,42 +0,0 @@
-Mediatek DPI Device
-===================
-
-The Mediatek DPI function block is a sink of the display subsystem and
-provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel
-output bus.
-
-Required properties:
-- compatible: "mediatek,<chip>-dpi"
-  the supported chips are mt2701 , mt8173 and mt8183.
-- reg: Physical base address and length of the controller's registers
-- interrupts: The interrupt signal from the function block.
-- clocks: device clocks
-  See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
-- clock-names: must contain "pixel", "engine", and "pll"
-- port: Output port node with endpoint definitions as described in
-  Documentation/devicetree/bindings/graph.txt. This port should be connected
-  to the input port of an attached HDMI or LVDS encoder chip.
-
-Optional properties:
-- pinctrl-names: Contain "default" and "sleep".
-
-Example:
-
-dpi0: dpi@1401d000 {
-	compatible = "mediatek,mt8173-dpi";
-	reg = <0 0x1401d000 0 0x1000>;
-	interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
-	clocks = <&mmsys CLK_MM_DPI_PIXEL>,
-		 <&mmsys CLK_MM_DPI_ENGINE>,
-		 <&apmixedsys CLK_APMIXED_TVDPLL>;
-	clock-names = "pixel", "engine", "pll";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&dpi_pin_func>;
-	pinctrl-1 = <&dpi_pin_idle>;
-
-	port {
-		dpi0_out: endpoint {
-			remote-endpoint = <&hdmi0_in>;
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
new file mode 100644
index 000000000000..2c2d6a71cb8b
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
@@ -0,0 +1,97 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/mediatek/mediatek,dpi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: mediatek DPI Controller Device Tree Bindings
+
+maintainers:
+  - CK Hu <ck.hu@mediatek.com>
+  - Jitao shi <jitao.shi@mediatek.com>
+
+description: |
+  The Mediatek DPI function block is a sink of the display subsystem and
+  provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel
+  output bus.
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-dpi
+      - mediatek,mt8173-dpi
+      - mediatek,mt8183-dpi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Pixel Clock
+      - description: Engine Clock
+      - description: DPI PLL
+
+  clock-names:
+    items:
+      - const: pixel
+      - const: engine
+      - const: pll
+
+  pinctrl-0: true
+  pinctrl-1: true
+
+  pinctrl-names:
+    items:
+      - const: default
+      - const: sleep
+
+  port:
+    type: object
+    description:
+      Output port node with endpoint definitions as described in
+      Documentation/devicetree/bindings/graph.txt. This port should be connected
+      to the input port of an attached HDMI or LVDS encoder chip.
+
+    properties:
+      endpoint:
+        type: object
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/mt8173-clk.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    dpi0: dpi@1401d000 {
+        compatible = "mediatek,mt8173-dpi";
+        reg = <0 0x1401d000 0 0x1000>;
+        interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
+        clocks = <&mmsys CLK_MM_DPI_PIXEL>,
+             <&mmsys CLK_MM_DPI_ENGINE>,
+             <&apmixedsys CLK_APMIXED_TVDPLL>;
+        clock-names = "pixel", "engine", "pll";
+        pinctrl-names = "default", "sleep";
+        pinctrl-0 = <&dpi_pin_func>;
+        pinctrl-1 = <&dpi_pin_idle>;
+
+        port {
+            dpi0_out: endpoint {
+                remote-endpoint = <&hdmi0_in>;
+            };
+        };
+    };
+
+...
-- 
2.12.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v15 2/3] dt-bindings: display: mediatek: convert the document format from txt to yaml

[Rob Herring]

On Wed, 15 Apr 2020 09:13:18 +0800, Jitao Shi wrote:
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  .../bindings/display/mediatek/mediatek,dpi.txt     | 42 ----------
>  .../bindings/display/mediatek/mediatek,dpi.yaml    | 97 ++++++++++++++++++++++
>  2 files changed, 97 insertions(+), 42 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
>  create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v15 2/3] dt-bindings: display: mediatek: convert the document format from txt to yaml

[Chun-Kuang Hu]

Hi, Jitao:

Please fixup these checkpatch warnings.

WARNING: Missing commit description - Add an appropriate one
WARNING: DT binding docs and includes should be a separate patch. See:
Documentation/devicetree/bindings/submitting-patches.txt
WARNING: DT binding docs and includes should be a separate patch. See:
Documentation/devicetree/bindings/submitting-patches.txt
WARNING: DT binding documents should be licensed (GPL-2.0-only OR BSD-2-Clause)
#71: FILE: Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml:1:
+# SPDX-License-Identifier: GPL-2.0

Regards,
Chun-Kuang.

Jitao Shi <jitao.shi@mediatek.com> 於 2020年4月15日 週三 上午9:13寫道：
>
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  .../bindings/display/mediatek/mediatek,dpi.txt     | 42 ----------
>  .../bindings/display/mediatek/mediatek,dpi.yaml    | 97 ++++++++++++++++++++++
>  2 files changed, 97 insertions(+), 42 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
>  create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
>
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> deleted file mode 100644
> index 77def4456706..000000000000
> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> +++ /dev/null
> @@ -1,42 +0,0 @@
> -Mediatek DPI Device
> -===================
> -
> -The Mediatek DPI function block is a sink of the display subsystem and
> -provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel
> -output bus.
> -
> -Required properties:
> -- compatible: "mediatek,<chip>-dpi"
> -  the supported chips are mt2701 , mt8173 and mt8183.
> -- reg: Physical base address and length of the controller's registers
> -- interrupts: The interrupt signal from the function block.
> -- clocks: device clocks
> -  See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
> -- clock-names: must contain "pixel", "engine", and "pll"
> -- port: Output port node with endpoint definitions as described in
> -  Documentation/devicetree/bindings/graph.txt. This port should be connected
> -  to the input port of an attached HDMI or LVDS encoder chip.
> -
> -Optional properties:
> -- pinctrl-names: Contain "default" and "sleep".
> -
> -Example:
> -
> -dpi0: dpi@1401d000 {
> -       compatible = "mediatek,mt8173-dpi";
> -       reg = <0 0x1401d000 0 0x1000>;
> -       interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
> -       clocks = <&mmsys CLK_MM_DPI_PIXEL>,
> -                <&mmsys CLK_MM_DPI_ENGINE>,
> -                <&apmixedsys CLK_APMIXED_TVDPLL>;
> -       clock-names = "pixel", "engine", "pll";
> -       pinctrl-names = "default", "sleep";
> -       pinctrl-0 = <&dpi_pin_func>;
> -       pinctrl-1 = <&dpi_pin_idle>;
> -
> -       port {
> -               dpi0_out: endpoint {
> -                       remote-endpoint = <&hdmi0_in>;
> -               };
> -       };
> -};
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
> new file mode 100644
> index 000000000000..2c2d6a71cb8b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
> @@ -0,0 +1,97 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/mediatek/mediatek,dpi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: mediatek DPI Controller Device Tree Bindings
> +
> +maintainers:
> +  - CK Hu <ck.hu@mediatek.com>
> +  - Jitao shi <jitao.shi@mediatek.com>
> +
> +description: |
> +  The Mediatek DPI function block is a sink of the display subsystem and
> +  provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel
> +  output bus.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - mediatek,mt2701-dpi
> +      - mediatek,mt8173-dpi
> +      - mediatek,mt8183-dpi
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    items:
> +      - description: Pixel Clock
> +      - description: Engine Clock
> +      - description: DPI PLL
> +
> +  clock-names:
> +    items:
> +      - const: pixel
> +      - const: engine
> +      - const: pll
> +
> +  pinctrl-0: true
> +  pinctrl-1: true
> +
> +  pinctrl-names:
> +    items:
> +      - const: default
> +      - const: sleep
> +
> +  port:
> +    type: object
> +    description:
> +      Output port node with endpoint definitions as described in
> +      Documentation/devicetree/bindings/graph.txt. This port should be connected
> +      to the input port of an attached HDMI or LVDS encoder chip.
> +
> +    properties:
> +      endpoint:
> +        type: object
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - clocks
> +  - clock-names
> +  - port
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/clock/mt8173-clk.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    dpi0: dpi@1401d000 {
> +        compatible = "mediatek,mt8173-dpi";
> +        reg = <0 0x1401d000 0 0x1000>;
> +        interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
> +        clocks = <&mmsys CLK_MM_DPI_PIXEL>,
> +             <&mmsys CLK_MM_DPI_ENGINE>,
> +             <&apmixedsys CLK_APMIXED_TVDPLL>;
> +        clock-names = "pixel", "engine", "pll";
> +        pinctrl-names = "default", "sleep";
> +        pinctrl-0 = <&dpi_pin_func>;
> +        pinctrl-1 = <&dpi_pin_idle>;
> +
> +        port {
> +            dpi0_out: endpoint {
> +                remote-endpoint = <&hdmi0_in>;
> +            };
> +        };
> +    };
> +
> +...
> --
> 2.12.5
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v15 3/3] drm/mediatek: set dpi pin mode to gpio low to avoid leakage current

[Jitao Shi]

Config dpi pins mode to output and pull low when dpi is disabled.
Aovid leakage current from some dpi pins (Hsync Vsync DE ... ).

Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dpi.c | 31 +++++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
index 087f5ce732e1..1e01254788d9 100644
--- a/drivers/gpu/drm/mediatek/mtk_dpi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
@@ -10,7 +10,9 @@
 #include <linux/kernel.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_gpio.h>
 #include <linux/of_graph.h>
+#include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
 #include <linux/types.h>
 
@@ -74,6 +76,9 @@ struct mtk_dpi {
 	enum mtk_dpi_out_yc_map yc_map;
 	enum mtk_dpi_out_bit_num bit_num;
 	enum mtk_dpi_out_channel_swap channel_swap;
+	struct pinctrl *pinctrl;
+	struct pinctrl_state *pins_gpio;
+	struct pinctrl_state *pins_dpi;
 	int refcount;
 };
 
@@ -379,6 +384,9 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi)
 	if (--dpi->refcount != 0)
 		return;
 
+	if (dpi->pinctrl && dpi->pins_gpio)
+		pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
+
 	mtk_dpi_disable(dpi);
 	clk_disable_unprepare(dpi->pixel_clk);
 	clk_disable_unprepare(dpi->engine_clk);
@@ -403,6 +411,9 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi)
 		goto err_pixel;
 	}
 
+	if (dpi->pinctrl && dpi->pins_dpi)
+		pinctrl_select_state(dpi->pinctrl, dpi->pins_dpi);
+
 	mtk_dpi_enable(dpi);
 	return 0;
 
@@ -705,6 +716,26 @@ static int mtk_dpi_probe(struct platform_device *pdev)
 	dpi->dev = dev;
 	dpi->conf = (struct mtk_dpi_conf *)of_device_get_match_data(dev);
 
+	dpi->pinctrl = devm_pinctrl_get(&pdev->dev);
+	if (IS_ERR(dpi->pinctrl)) {
+		dpi->pinctrl = NULL;
+		dev_dbg(&pdev->dev, "Cannot find pinctrl!\n");
+	}
+	if (dpi->pinctrl) {
+		dpi->pins_gpio = pinctrl_lookup_state(dpi->pinctrl, "sleep");
+		if (IS_ERR(dpi->pins_gpio)) {
+			dpi->pins_gpio = NULL;
+			dev_dbg(&pdev->dev, "Cannot find pinctrl idle!\n");
+		}
+		if (dpi->pins_gpio)
+			pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
+
+		dpi->pins_dpi = pinctrl_lookup_state(dpi->pinctrl, "default");
+		if (IS_ERR(dpi->pins_dpi)) {
+			dpi->pins_dpi = NULL;
+			dev_dbg(&pdev->dev, "Cannot find pinctrl active!\n");
+		}
+	}
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dpi->regs = devm_ioremap_resource(dev, mem);
 	if (IS_ERR(dpi->regs)) {
-- 
2.12.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v15 3/3] drm/mediatek: set dpi pin mode to gpio low to avoid leakage current

[Chun-Kuang Hu]

Hi, Jitao:

Jitao Shi <jitao.shi@mediatek.com> 於 2020年4月15日 週三 上午9:13寫道：
>
> Config dpi pins mode to output and pull low when dpi is disabled.
> Aovid leakage current from some dpi pins (Hsync Vsync DE ... ).

Applied to mediatek-drm-next [1], thanks.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux.git/log/?h=mediatek-drm-next

Regards,Chun-Kuang.

>
> Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dpi.c | 31 +++++++++++++++++++++++++++++++
>  1 file changed, 31 insertions(+)
>
> diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
> index 087f5ce732e1..1e01254788d9 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> @@ -10,7 +10,9 @@
>  #include <linux/kernel.h>
>  #include <linux/of.h>
>  #include <linux/of_device.h>
> +#include <linux/of_gpio.h>
>  #include <linux/of_graph.h>
> +#include <linux/pinctrl/consumer.h>
>  #include <linux/platform_device.h>
>  #include <linux/types.h>
>
> @@ -74,6 +76,9 @@ struct mtk_dpi {
>         enum mtk_dpi_out_yc_map yc_map;
>         enum mtk_dpi_out_bit_num bit_num;
>         enum mtk_dpi_out_channel_swap channel_swap;
> +       struct pinctrl *pinctrl;
> +       struct pinctrl_state *pins_gpio;
> +       struct pinctrl_state *pins_dpi;
>         int refcount;
>  };
>
> @@ -379,6 +384,9 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi)
>         if (--dpi->refcount != 0)
>                 return;
>
> +       if (dpi->pinctrl && dpi->pins_gpio)
> +               pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
> +
>         mtk_dpi_disable(dpi);
>         clk_disable_unprepare(dpi->pixel_clk);
>         clk_disable_unprepare(dpi->engine_clk);
> @@ -403,6 +411,9 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi)
>                 goto err_pixel;
>         }
>
> +       if (dpi->pinctrl && dpi->pins_dpi)
> +               pinctrl_select_state(dpi->pinctrl, dpi->pins_dpi);
> +
>         mtk_dpi_enable(dpi);
>         return 0;
>
> @@ -705,6 +716,26 @@ static int mtk_dpi_probe(struct platform_device *pdev)
>         dpi->dev = dev;
>         dpi->conf = (struct mtk_dpi_conf *)of_device_get_match_data(dev);
>
> +       dpi->pinctrl = devm_pinctrl_get(&pdev->dev);
> +       if (IS_ERR(dpi->pinctrl)) {
> +               dpi->pinctrl = NULL;
> +               dev_dbg(&pdev->dev, "Cannot find pinctrl!\n");
> +       }
> +       if (dpi->pinctrl) {
> +               dpi->pins_gpio = pinctrl_lookup_state(dpi->pinctrl, "sleep");
> +               if (IS_ERR(dpi->pins_gpio)) {
> +                       dpi->pins_gpio = NULL;
> +                       dev_dbg(&pdev->dev, "Cannot find pinctrl idle!\n");
> +               }
> +               if (dpi->pins_gpio)
> +                       pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
> +
> +               dpi->pins_dpi = pinctrl_lookup_state(dpi->pinctrl, "default");
> +               if (IS_ERR(dpi->pins_dpi)) {
> +                       dpi->pins_dpi = NULL;
> +                       dev_dbg(&pdev->dev, "Cannot find pinctrl active!\n");
> +               }
> +       }
>         mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>         dpi->regs = devm_ioremap_resource(dev, mem);
>         if (IS_ERR(dpi->regs)) {
> --
> 2.12.5
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel