* [PATCH 2/4] ARM: dts: stm32: Add GPIO LEDs for STM32MP1 DHCOM PDK2
2020-05-07 15:13 [PATCH 1/4] ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2 Marek Vasut
@ 2020-05-07 15:13 ` Marek Vasut
2020-05-07 15:13 ` [PATCH 3/4] ARM: dts: stm32: Split SoC-independent parts of DHCOM SOM and PDK2 Marek Vasut
2020-05-07 15:13 ` [PATCH 4/4] ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board Marek Vasut
2 siblings, 0 replies; 4+ messages in thread
From: Marek Vasut @ 2020-05-07 15:13 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32
Add bindings for the four GPIO LEDs on DH PDK2 board. Note that LED5
GPIO-E may conflict with touchscreen interrupt, hence LED5 must be
disabled when using the DH 560-200 display unit with touchscreen.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts | 28 ++++++++++++++++++++
1 file changed, 28 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts b/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts
index e5036c9b9e92..b380268750f3 100644
--- a/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts
+++ b/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts
@@ -89,6 +89,34 @@ button-3 {
};
};
+ led {
+ compatible = "gpio-leds";
+
+ led-0 {
+ label = "green:led5";
+ gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led-1 {
+ label = "green:led6";
+ gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led-2 {
+ label = "green:led7";
+ gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led-3 {
+ label = "green:led8";
+ gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
panel {
compatible = "edt,etm0700g0edh6";
backlight = <&display_bl>;
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH 3/4] ARM: dts: stm32: Split SoC-independent parts of DHCOM SOM and PDK2
2020-05-07 15:13 [PATCH 1/4] ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2 Marek Vasut
2020-05-07 15:13 ` [PATCH 2/4] ARM: dts: stm32: Add GPIO LEDs " Marek Vasut
@ 2020-05-07 15:13 ` Marek Vasut
2020-05-07 15:13 ` [PATCH 4/4] ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board Marek Vasut
2 siblings, 0 replies; 4+ messages in thread
From: Marek Vasut @ 2020-05-07 15:13 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32
The DH Electronics PDK2 can be populated with SoM with any STM32MP15xx
variant. Split the SoC-independent parts of the SoM and PDK2 into the
stm32mp15xx-dhcom-*.dtsi and reduce stm32mp157c-dhcom-*dts* to example
of adding STM32MP157C variant of the SoM into a PDK2 carrier board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts | 339 +---------------
arch/arm/boot/dts/stm32mp157c-dhcom-som.dtsi | 359 +----------------
arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 337 ++++++++++++++++
arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi | 361 ++++++++++++++++++
4 files changed, 708 insertions(+), 688 deletions(-)
create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
diff --git a/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts b/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts
index b380268750f3..65322b5c59d3 100644
--- a/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts
+++ b/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts
@@ -1,243 +1,16 @@
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
/*
- * Copyright (C) 2019 Marek Vasut <marex@denx.de>
+ * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
*/
+/dts-v1/;
#include "stm32mp157c-dhcom-som.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pwm/pwm.h>
+#include "stm32mp15xx-dhcom-pdk2.dtsi"
/ {
- model = "STMicroelectronics STM32MP157C DHCOM Premium Developer Kit (2)";
- compatible = "dh,stm32mp157c-dhcom-pdk2", "st,stm32mp157";
-
- aliases {
- serial0 = &uart4;
- serial1 = &usart3;
- serial2 = &uart8;
- ethernet0 = ðernet0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- clk_ext_audio_codec: clock-codec {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <24000000>;
- };
-
- display_bl: display-bl {
- compatible = "pwm-backlight";
- pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
- brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
- default-brightness-level = <8>;
- enable-gpios = <&gpioi 0 GPIO_ACTIVE_HIGH>;
- status = "okay";
- };
-
- ethernet_vio: vioregulator {
- compatible = "regulator-fixed";
- regulator-name = "vio";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- gpio-keys-polled {
- compatible = "gpio-keys-polled";
- #size-cells = <0>;
- poll-interval = <20>;
-
- /*
- * The EXTi IRQ line 3 is shared with touchscreen and ethernet,
- * so mark this as polled GPIO key.
- */
- button-0 {
- label = "TA1-GPIO-A";
- linux,code = <KEY_A>;
- gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
- };
- };
-
- gpio-keys {
- compatible = "gpio-keys";
- #size-cells = <0>;
-
- button-1 {
- label = "TA2-GPIO-B";
- linux,code = <KEY_B>;
- gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
- wakeup-source;
- };
-
- button-2 {
- label = "TA3-GPIO-C";
- linux,code = <KEY_C>;
- gpios = <&gpioi 11 GPIO_ACTIVE_LOW>;
- wakeup-source;
- };
-
- button-3 {
- label = "TA4-GPIO-D";
- linux,code = <KEY_D>;
- gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
- wakeup-source;
- };
- };
-
- led {
- compatible = "gpio-leds";
-
- led-0 {
- label = "green:led5";
- gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
-
- led-1 {
- label = "green:led6";
- gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
-
- led-2 {
- label = "green:led7";
- gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
-
- led-3 {
- label = "green:led8";
- gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
- };
-
- panel {
- compatible = "edt,etm0700g0edh6";
- backlight = <&display_bl>;
-
- port {
- lcd_panel_in: endpoint {
- remote-endpoint = <&lcd_display_out>;
- };
- };
- };
-
- sound {
- compatible = "audio-graph-card";
- routing =
- "MIC_IN", "Capture",
- "Capture", "Mic Bias",
- "Playback", "HP_OUT";
- dais = <&sai2a_port &sai2b_port>;
- status = "okay";
- };
-};
-
-&cec {
- pinctrl-names = "default";
- pinctrl-0 = <&cec_pins_a>;
- status = "okay";
-};
-
-ðernet0 {
- status = "okay";
- pinctrl-0 = <ðernet0_rmii_pins_a>;
- pinctrl-1 = <ðernet0_rmii_sleep_pins_a>;
- pinctrl-names = "default", "sleep";
- phy-mode = "rmii";
- max-speed = <100>;
- phy-handle = <&phy0>;
- st,eth-ref-clk-sel;
- phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
-
- mdio0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "snps,dwmac-mdio";
-
- phy0: ethernet-phy@1 {
- reg = <1>;
- };
- };
-};
-
-&i2c2 { /* Header X22 */
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-&i2c5 { /* Header X21 */
- pinctrl-names = "default";
- pinctrl-0 = <&i2c5_pins_a>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
-
- sgtl5000: codec@a {
- compatible = "fsl,sgtl5000";
- reg = <0x0a>;
- #sound-dai-cells = <0>;
- clocks = <&clk_ext_audio_codec>;
- VDDA-supply = <&v3v3>;
- VDDIO-supply = <&vdd>;
-
- sgtl5000_port: port {
- #address-cells = <1>;
- #size-cells = <0>;
-
- sgtl5000_tx_endpoint: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&sai2a_endpoint>;
- frame-master;
- bitclock-master;
- };
-
- sgtl5000_rx_endpoint: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&sai2b_endpoint>;
- frame-master;
- bitclock-master;
- };
- };
-
- };
-
- polytouch@38 {
- compatible = "edt,edt-ft5x06";
- reg = <0x38>;
- interrupt-parent = <&gpiog>;
- interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
- linux,wakeup;
- };
-};
-
-<dc {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <<dc_pins_b>;
- pinctrl-1 = <<dc_sleep_pins_b>;
- status = "okay";
-
- port {
- lcd_display_out: endpoint {
- remote-endpoint = <&lcd_panel_in>;
- };
- };
+ model = "DH Electronics STM32MP157C DHCOM Premium Developer Kit (2)";
+ compatible = "dh,stm32mp157c-dhcom-pdk2", "dh,stm32mp157c-dhcom-som",
+ "st,stm32mp157";
};
&m_can1 {
@@ -246,103 +19,3 @@ &m_can1 {
pinctrl-1 = <&m_can1_sleep_pins_a>;
status = "okay";
};
-
-&sai2 {
- clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
- clock-names = "pclk", "x8k", "x11k";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sai2a_pins_b &sai2b_pins_b>;
- pinctrl-1 = <&sai2a_sleep_pins_b &sai2b_sleep_pins_b>;
- status = "okay";
-
- sai2a: audio-controller@4400b004 {
- #clock-cells = <0>;
- dma-names = "tx";
- clocks = <&rcc SAI2_K>;
- clock-names = "sai_ck";
- status = "okay";
-
- sai2a_port: port {
- sai2a_endpoint: endpoint {
- remote-endpoint = <&sgtl5000_tx_endpoint>;
- format = "i2s";
- mclk-fs = <512>;
- dai-tdm-slot-num = <2>;
- dai-tdm-slot-width = <16>;
- };
- };
- };
-
- sai2b: audio-controller@4400b024 {
- dma-names = "rx";
- st,sync = <&sai2a 2>;
- clocks = <&rcc SAI2_K>, <&sai2a>;
- clock-names = "sai_ck", "MCLK";
- status = "okay";
-
- sai2b_port: port {
- sai2b_endpoint: endpoint {
- remote-endpoint = <&sgtl5000_rx_endpoint>;
- format = "i2s";
- mclk-fs = <512>;
- dai-tdm-slot-num = <2>;
- dai-tdm-slot-width = <16>;
- };
- };
- };
-};
-
-&timers2 {
- /* spare dmas for other usage (un-delete to enable pwm capture) */
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
- pwm2: pwm {
- pinctrl-0 = <&pwm2_pins_a>;
- pinctrl-names = "default";
- status = "okay";
- };
- timer@1 {
- status = "okay";
- };
-};
-
-&usart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&usart3_pins_a>;
- status = "okay";
-};
-
-&uart8 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart8_pins_a>;
- status = "okay";
-};
-
-&usbh_ehci {
- phys = <&usbphyc_port0>;
- status = "okay";
-};
-
-&usbotg_hs {
- dr_mode = "peripheral";
- phys = <&usbphyc_port1 0>;
- phy-names = "usb2-phy";
- status = "okay";
-};
-
-&usbphyc {
- status = "okay";
-};
-
-&usbphyc_port0 {
- phy-supply = <&vdd_usb>;
- vdda1v1-supply = <®11>;
- vdda1v8-supply = <®18>;
-};
-
-&usbphyc_port1 {
- phy-supply = <&vdd_usb>;
- vdda1v1-supply = <®11>;
- vdda1v8-supply = <®18>;
-};
diff --git a/arch/arm/boot/dts/stm32mp157c-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp157c-dhcom-som.dtsi
index f97e0d2ecf17..e03c12a82604 100644
--- a/arch/arm/boot/dts/stm32mp157c-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp157c-dhcom-som.dtsi
@@ -1,364 +1,13 @@
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
/*
- * Copyright (C) 2019 Marek Vasut <marex@denx.de>
+ * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
*/
-/dts-v1/;
#include "stm32mp157.dtsi"
#include "stm32mp15xc.dtsi"
-#include "stm32mp15-pinctrl.dtsi"
-#include "stm32mp15xxaa-pinctrl.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/mfd/st,stpmic1.h>
+#include "stm32mp15xx-dhcom-som.dtsi"
/ {
- memory@c0000000 {
- device_type = "memory";
- reg = <0xC0000000 0x40000000>;
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- mcuram2: mcuram2@10000000 {
- compatible = "shared-dma-pool";
- reg = <0x10000000 0x40000>;
- no-map;
- };
-
- vdev0vring0: vdev0vring0@10040000 {
- compatible = "shared-dma-pool";
- reg = <0x10040000 0x1000>;
- no-map;
- };
-
- vdev0vring1: vdev0vring1@10041000 {
- compatible = "shared-dma-pool";
- reg = <0x10041000 0x1000>;
- no-map;
- };
-
- vdev0buffer: vdev0buffer@10042000 {
- compatible = "shared-dma-pool";
- reg = <0x10042000 0x4000>;
- no-map;
- };
-
- mcuram: mcuram@30000000 {
- compatible = "shared-dma-pool";
- reg = <0x30000000 0x40000>;
- no-map;
- };
-
- retram: retram@38000000 {
- compatible = "shared-dma-pool";
- reg = <0x38000000 0x10000>;
- no-map;
- };
- };
-};
-
-&adc {
- vdd-supply = <&vdd>;
- vdda-supply = <&vdda>;
- vref-supply = <&vdda>;
- status = "okay";
-
- adc1: adc@0 {
- st,min-sample-time-nsecs = <5000>;
- st,adc-channels = <0>;
- status = "okay";
- };
-
- adc2: adc@100 {
- st,adc-channels = <1>;
- st,min-sample-time-nsecs = <5000>;
- status = "okay";
- };
-};
-
-&dac {
- pinctrl-names = "default";
- pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>;
- vref-supply = <&vdda>;
- status = "okay";
-
- dac1: dac@1 {
- status = "okay";
- };
- dac2: dac@2 {
- status = "okay";
- };
-};
-
-&dts {
- status = "okay";
-};
-
-&i2c4 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c4_pins_a>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
-
- rtc@32 {
- compatible = "microcrystal,rv8803";
- reg = <0x32>;
- };
-
- pmic: stpmic@33 {
- compatible = "st,stpmic1";
- reg = <0x33>;
- interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
- interrupt-controller;
- #interrupt-cells = <2>;
- status = "okay";
-
- regulators {
- compatible = "st,stpmic1-regulators";
- ldo1-supply = <&v3v3>;
- ldo2-supply = <&v3v3>;
- ldo3-supply = <&vdd_ddr>;
- ldo5-supply = <&v3v3>;
- ldo6-supply = <&v3v3>;
- pwr_sw1-supply = <&bst_out>;
- pwr_sw2-supply = <&bst_out>;
-
- vddcore: buck1 {
- regulator-name = "vddcore";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd_ddr: buck2 {
- regulator-name = "vdd_ddr";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd: buck3 {
- regulator-name = "vdd";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- st,mask-reset;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- v3v3: buck4 {
- regulator-name = "v3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-over-current-protection;
- regulator-initial-mode = <0>;
- };
-
- vdda: ldo1 {
- regulator-name = "vdda";
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- interrupts = <IT_CURLIM_LDO1 0>;
- };
-
- v2v8: ldo2 {
- regulator-name = "v2v8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- interrupts = <IT_CURLIM_LDO2 0>;
- };
-
- vtt_ddr: ldo3 {
- regulator-name = "vtt_ddr";
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <750000>;
- regulator-always-on;
- regulator-over-current-protection;
- };
-
- vdd_usb: ldo4 {
- regulator-name = "vdd_usb";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- interrupts = <IT_CURLIM_LDO4 0>;
- };
-
- vdd_sd: ldo5 {
- regulator-name = "vdd_sd";
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- interrupts = <IT_CURLIM_LDO5 0>;
- regulator-boot-on;
- };
-
- v1v8: ldo6 {
- regulator-name = "v1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- interrupts = <IT_CURLIM_LDO6 0>;
- };
-
- vref_ddr: vref_ddr {
- regulator-name = "vref_ddr";
- regulator-always-on;
- regulator-over-current-protection;
- };
-
- bst_out: boost {
- regulator-name = "bst_out";
- interrupts = <IT_OCP_BOOST 0>;
- };
-
- vbus_otg: pwr_sw1 {
- regulator-name = "vbus_otg";
- interrupts = <IT_OCP_OTG 0>;
- };
-
- vbus_sw: pwr_sw2 {
- regulator-name = "vbus_sw";
- interrupts = <IT_OCP_SWOUT 0>;
- regulator-active-discharge;
- };
- };
-
- onkey {
- compatible = "st,stpmic1-onkey";
- interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
- interrupt-names = "onkey-falling", "onkey-rising";
- power-off-time-sec = <10>;
- status = "okay";
- };
-
- watchdog {
- compatible = "st,stpmic1-wdt";
- status = "disabled";
- };
- };
-
- touchscreen@49 {
- compatible = "ti,tsc2004";
- reg = <0x49>;
- vio-supply = <&v3v3>;
- interrupts-extended = <&gpioh 3 IRQ_TYPE_EDGE_FALLING>;
- };
-
- eeprom@50 {
- compatible = "atmel,24c02";
- reg = <0x50>;
- pagesize = <16>;
- };
-};
-
-&ipcc {
- status = "okay";
-};
-
-&iwdg2 {
- timeout-sec = <32>;
- status = "okay";
-};
-
-&m4_rproc {
- memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
- <&vdev0vring1>, <&vdev0buffer>;
- mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
- mbox-names = "vq0", "vq1", "shutdown";
- interrupt-parent = <&exti>;
- interrupts = <68 1>;
- status = "okay";
-};
-
-&pwr_regulators {
- vdd-supply = <&vdd>;
- vdd_3v3_usbfs-supply = <&vdd_usb>;
-};
-
-&qspi {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
- pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>;
- reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- flash0: mx66l51235l@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-rx-bus-width = <4>;
- spi-max-frequency = <108000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- };
-};
-
-&rng1 {
- status = "okay";
-};
-
-&rtc {
- status = "okay";
-};
-
-&sdmmc1 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
- pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
- pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
- broken-cd;
- st,sig-dir;
- st,neg-edge;
- st,use-ckin;
- bus-width = <4>;
- vmmc-supply = <&vdd_sd>;
- status = "okay";
-};
-
-&sdmmc2 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
- pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
- pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
- non-removable;
- no-sd;
- no-sdio;
- st,neg-edge;
- bus-width = <8>;
- vmmc-supply = <&v3v3>;
- vqmmc-supply = <&v3v3>;
- mmc-ddr-3_3v;
- status = "okay";
-};
-
-&sdmmc3 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc3_b4_pins_a>;
- pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
- pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
- broken-cd;
- st,neg-edge;
- bus-width = <4>;
- vmmc-supply = <&v3v3>;
- vqmmc-supply = <&v3v3>;
- mmc-ddr-3_3v;
- status = "okay";
-};
-
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart4_pins_a>;
- status = "okay";
+ model = "DH Electronics STM32MP157C DHCOM SoM";
+ compatible = "dh,stm32mp157c-dhcom-som", "st,stm32mp157";
};
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
new file mode 100644
index 000000000000..7c4bd615b311
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
@@ -0,0 +1,337 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ aliases {
+ serial0 = &uart4;
+ serial1 = &usart3;
+ serial2 = &uart8;
+ ethernet0 = ðernet0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ clk_ext_audio_codec: clock-codec {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ };
+
+ display_bl: display-bl {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
+ default-brightness-level = <8>;
+ enable-gpios = <&gpioi 0 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ ethernet_vio: vioregulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vio";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ /*
+ * The EXTi IRQ line 3 is shared with touchscreen and ethernet,
+ * so mark this as polled GPIO key.
+ */
+ button-0 {
+ label = "TA1-GPIO-A";
+ linux,code = <KEY_A>;
+ gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #size-cells = <0>;
+
+ button-1 {
+ label = "TA2-GPIO-B";
+ linux,code = <KEY_B>;
+ gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+
+ button-2 {
+ label = "TA3-GPIO-C";
+ linux,code = <KEY_C>;
+ gpios = <&gpioi 11 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+
+ button-3 {
+ label = "TA4-GPIO-D";
+ linux,code = <KEY_D>;
+ gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+ };
+
+ led {
+ compatible = "gpio-leds";
+
+ led-0 {
+ label = "green:led5";
+ gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led-1 {
+ label = "green:led6";
+ gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led-2 {
+ label = "green:led7";
+ gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led-3 {
+ label = "green:led8";
+ gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ panel {
+ compatible = "edt,etm0700g0edh6";
+ backlight = <&display_bl>;
+
+ port {
+ lcd_panel_in: endpoint {
+ remote-endpoint = <&lcd_display_out>;
+ };
+ };
+ };
+
+ sound {
+ compatible = "audio-graph-card";
+ routing =
+ "MIC_IN", "Capture",
+ "Capture", "Mic Bias",
+ "Playback", "HP_OUT";
+ dais = <&sai2a_port &sai2b_port>;
+ status = "okay";
+ };
+};
+
+&cec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cec_pins_a>;
+ status = "okay";
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rmii_pins_a>;
+ pinctrl-1 = <ðernet0_rmii_sleep_pins_a>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rmii";
+ max-speed = <100>;
+ phy-handle = <&phy0>;
+ st,eth-ref-clk-sel;
+ phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+ };
+};
+
+&i2c2 { /* Header X22 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "okay";
+};
+
+&i2c5 { /* Header X21 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_pins_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ #sound-dai-cells = <0>;
+ clocks = <&clk_ext_audio_codec>;
+ VDDA-supply = <&v3v3>;
+ VDDIO-supply = <&vdd>;
+
+ sgtl5000_port: port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sgtl5000_tx_endpoint: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&sai2a_endpoint>;
+ frame-master;
+ bitclock-master;
+ };
+
+ sgtl5000_rx_endpoint: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&sai2b_endpoint>;
+ frame-master;
+ bitclock-master;
+ };
+ };
+
+ };
+
+ polytouch@38 {
+ compatible = "edt,edt-ft5x06";
+ reg = <0x38>;
+ interrupt-parent = <&gpiog>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
+ linux,wakeup;
+ };
+};
+
+<dc {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <<dc_pins_b>;
+ pinctrl-1 = <<dc_sleep_pins_b>;
+ status = "okay";
+
+ port {
+ lcd_display_out: endpoint {
+ remote-endpoint = <&lcd_panel_in>;
+ };
+ };
+};
+
+&sai2 {
+ clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+ clock-names = "pclk", "x8k", "x11k";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sai2a_pins_b &sai2b_pins_b>;
+ pinctrl-1 = <&sai2a_sleep_pins_b &sai2b_sleep_pins_b>;
+ status = "okay";
+
+ sai2a: audio-controller@4400b004 {
+ #clock-cells = <0>;
+ dma-names = "tx";
+ clocks = <&rcc SAI2_K>;
+ clock-names = "sai_ck";
+ status = "okay";
+
+ sai2a_port: port {
+ sai2a_endpoint: endpoint {
+ remote-endpoint = <&sgtl5000_tx_endpoint>;
+ format = "i2s";
+ mclk-fs = <512>;
+ dai-tdm-slot-num = <2>;
+ dai-tdm-slot-width = <16>;
+ };
+ };
+ };
+
+ sai2b: audio-controller@4400b024 {
+ dma-names = "rx";
+ st,sync = <&sai2a 2>;
+ clocks = <&rcc SAI2_K>, <&sai2a>;
+ clock-names = "sai_ck", "MCLK";
+ status = "okay";
+
+ sai2b_port: port {
+ sai2b_endpoint: endpoint {
+ remote-endpoint = <&sgtl5000_rx_endpoint>;
+ format = "i2s";
+ mclk-fs = <512>;
+ dai-tdm-slot-num = <2>;
+ dai-tdm-slot-width = <16>;
+ };
+ };
+ };
+};
+
+&timers2 {
+ /* spare dmas for other usage (un-delete to enable pwm capture) */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "okay";
+ pwm2: pwm {
+ pinctrl-0 = <&pwm2_pins_a>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+ timer@1 {
+ status = "okay";
+ };
+};
+
+&usart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usart3_pins_a>;
+ status = "okay";
+};
+
+&uart8 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart8_pins_a>;
+ status = "okay";
+};
+
+&usbh_ehci {
+ phys = <&usbphyc_port0>;
+ status = "okay";
+};
+
+&usbotg_hs {
+ dr_mode = "peripheral";
+ phys = <&usbphyc_port1 0>;
+ phy-names = "usb2-phy";
+ status = "okay";
+};
+
+&usbphyc {
+ status = "okay";
+};
+
+&usbphyc_port0 {
+ phy-supply = <&vdd_usb>;
+ vdda1v1-supply = <®11>;
+ vdda1v8-supply = <®18>;
+};
+
+&usbphyc_port1 {
+ phy-supply = <&vdd_usb>;
+ vdda1v1-supply = <®11>;
+ vdda1v8-supply = <®18>;
+};
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
new file mode 100644
index 000000000000..ba905196fb54
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
@@ -0,0 +1,361 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
+ */
+
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+ memory@c0000000 {
+ device_type = "memory";
+ reg = <0xC0000000 0x40000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mcuram2: mcuram2@10000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10000000 0x40000>;
+ no-map;
+ };
+
+ vdev0vring0: vdev0vring0@10040000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10040000 0x1000>;
+ no-map;
+ };
+
+ vdev0vring1: vdev0vring1@10041000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10041000 0x1000>;
+ no-map;
+ };
+
+ vdev0buffer: vdev0buffer@10042000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10042000 0x4000>;
+ no-map;
+ };
+
+ mcuram: mcuram@30000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x30000000 0x40000>;
+ no-map;
+ };
+
+ retram: retram@38000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x38000000 0x10000>;
+ no-map;
+ };
+ };
+};
+
+&adc {
+ vdd-supply = <&vdd>;
+ vdda-supply = <&vdda>;
+ vref-supply = <&vdda>;
+ status = "okay";
+
+ adc1: adc@0 {
+ st,min-sample-time-nsecs = <5000>;
+ st,adc-channels = <0>;
+ status = "okay";
+ };
+
+ adc2: adc@100 {
+ st,adc-channels = <1>;
+ st,min-sample-time-nsecs = <5000>;
+ status = "okay";
+ };
+};
+
+&dac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>;
+ vref-supply = <&vdda>;
+ status = "okay";
+
+ dac1: dac@1 {
+ status = "okay";
+ };
+ dac2: dac@2 {
+ status = "okay";
+ };
+};
+
+&dts {
+ status = "okay";
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ rtc@32 {
+ compatible = "microcrystal,rv8803";
+ reg = <0x32>;
+ };
+
+ pmic: stpmic@33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ status = "okay";
+
+ regulators {
+ compatible = "st,stpmic1-regulators";
+ ldo1-supply = <&v3v3>;
+ ldo2-supply = <&v3v3>;
+ ldo3-supply = <&vdd_ddr>;
+ ldo5-supply = <&v3v3>;
+ ldo6-supply = <&v3v3>;
+ pwr_sw1-supply = <&bst_out>;
+ pwr_sw2-supply = <&bst_out>;
+
+ vddcore: buck1 {
+ regulator-name = "vddcore";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd_ddr: buck2 {
+ regulator-name = "vdd_ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd: buck3 {
+ regulator-name = "vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ st,mask-reset;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ v3v3: buck4 {
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ regulator-initial-mode = <0>;
+ };
+
+ vdda: ldo1 {
+ regulator-name = "vdda";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO1 0>;
+ };
+
+ v2v8: ldo2 {
+ regulator-name = "v2v8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ interrupts = <IT_CURLIM_LDO2 0>;
+ };
+
+ vtt_ddr: ldo3 {
+ regulator-name = "vtt_ddr";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <750000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ vdd_usb: ldo4 {
+ regulator-name = "vdd_usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ interrupts = <IT_CURLIM_LDO4 0>;
+ };
+
+ vdd_sd: ldo5 {
+ regulator-name = "vdd_sd";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO5 0>;
+ regulator-boot-on;
+ };
+
+ v1v8: ldo6 {
+ regulator-name = "v1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ interrupts = <IT_CURLIM_LDO6 0>;
+ };
+
+ vref_ddr: vref_ddr {
+ regulator-name = "vref_ddr";
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ bst_out: boost {
+ regulator-name = "bst_out";
+ interrupts = <IT_OCP_BOOST 0>;
+ };
+
+ vbus_otg: pwr_sw1 {
+ regulator-name = "vbus_otg";
+ interrupts = <IT_OCP_OTG 0>;
+ };
+
+ vbus_sw: pwr_sw2 {
+ regulator-name = "vbus_sw";
+ interrupts = <IT_OCP_SWOUT 0>;
+ regulator-active-discharge;
+ };
+ };
+
+ onkey {
+ compatible = "st,stpmic1-onkey";
+ interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+ interrupt-names = "onkey-falling", "onkey-rising";
+ power-off-time-sec = <10>;
+ status = "okay";
+ };
+
+ watchdog {
+ compatible = "st,stpmic1-wdt";
+ status = "disabled";
+ };
+ };
+
+ touchscreen@49 {
+ compatible = "ti,tsc2004";
+ reg = <0x49>;
+ vio-supply = <&v3v3>;
+ interrupts-extended = <&gpioh 3 IRQ_TYPE_EDGE_FALLING>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
+
+&ipcc {
+ status = "okay";
+};
+
+&iwdg2 {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&m4_rproc {
+ memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+ <&vdev0vring1>, <&vdev0buffer>;
+ mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+ mbox-names = "vq0", "vq1", "shutdown";
+ interrupt-parent = <&exti>;
+ interrupts = <68 1>;
+ status = "okay";
+};
+
+&pwr_regulators {
+ vdd-supply = <&vdd>;
+ vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
+ pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>;
+ reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ flash0: mx66l51235l@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&rng1 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+ broken-cd;
+ st,sig-dir;
+ st,neg-edge;
+ st,use-ckin;
+ bus-width = <4>;
+ vmmc-supply = <&vdd_sd>;
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ st,neg-edge;
+ bus-width = <8>;
+ vmmc-supply = <&v3v3>;
+ vqmmc-supply = <&v3v3>;
+ mmc-ddr-3_3v;
+ status = "okay";
+};
+
+&sdmmc3 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc3_b4_pins_a>;
+ pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+ broken-cd;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ vqmmc-supply = <&v3v3>;
+ mmc-ddr-3_3v;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+ status = "okay";
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH 4/4] ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board
2020-05-07 15:13 [PATCH 1/4] ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2 Marek Vasut
2020-05-07 15:13 ` [PATCH 2/4] ARM: dts: stm32: Add GPIO LEDs " Marek Vasut
2020-05-07 15:13 ` [PATCH 3/4] ARM: dts: stm32: Split SoC-independent parts of DHCOM SOM and PDK2 Marek Vasut
@ 2020-05-07 15:13 ` Marek Vasut
2 siblings, 0 replies; 4+ messages in thread
From: Marek Vasut @ 2020-05-07 15:13 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
The Avenger96 is in fact an assembly of DH Electronics DHCOR SoM on top
of an Avenger96 reference board. The DHCOR SoM can be populated with any
STM32MP15xx. Split the DTs to reflect this such that the common SoM and
Avenger96 parts are now in stm32mp15xx-dhcor-*dtsi and a specific example
implementation of STM32MP157A SoM and Avenger96 board is separated into
stm32mp157a-dhcor-*dts* . The stm32mp157a-avenger96.dts is retained for
the sake of backward naming compatibility.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 618 +-----------------
.../boot/dts/stm32mp157a-dhcor-avenger96.dts | 31 +
arch/arm/boot/dts/stm32mp157a-dhcor-som.dtsi | 15 +
.../boot/dts/stm32mp15xx-dhcor-avenger96.dtsi | 401 ++++++++++++
.../arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi | 23 +
arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi | 209 ++++++
7 files changed, 683 insertions(+), 615 deletions(-)
create mode 100644 arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts
create mode 100644 arch/arm/boot/dts/stm32mp157a-dhcor-som.dtsi
create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi
create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f43467b02bcd..d0f6c5838568 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1029,6 +1029,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
stm32h743i-eval.dtb \
stm32h743i-disco.dtb \
stm32mp157a-avenger96.dtb \
+ stm32mp157a-dhcor-avenger96.dtb \
stm32mp157a-dk1.dtb \
stm32mp157c-dhcom-pdk2.dtb \
stm32mp157c-dk2.dtb \
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index a9f3ba9da170..8a6eaca994d1 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -2,622 +2,10 @@
/*
* Copyright (C) Linaro Ltd 2019 - All Rights Reserved
* Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
*/
/dts-v1/;
-#include "stm32mp157.dtsi"
-#include "stm32mp15-pinctrl.dtsi"
-#include "stm32mp15xxac-pinctrl.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/mfd/st,stpmic1.h>
-
-/ {
- model = "Arrow Electronics STM32MP157A Avenger96 board";
- compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157";
-
- aliases {
- ethernet0 = ðernet0;
- mmc0 = &sdmmc1;
- serial0 = &uart4;
- serial1 = &uart7;
- serial2 = &usart2;
- spi0 = &qspi;
- };
-
- /* XTal Q1 */
- cec_clock: clk-cec-fixed {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- hdmi-out {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi_con: endpoint {
- remote-endpoint = <&adv7513_out>;
- };
- };
- };
-
- memory@c0000000 {
- device_type = "memory";
- reg = <0xc0000000 0x40000000>;
- };
-
- led {
- compatible = "gpio-leds";
- led1 {
- label = "green:user0";
- gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- default-state = "off";
- };
-
- led2 {
- label = "green:user1";
- gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc0";
- default-state = "off";
- };
-
- led3 {
- label = "green:user2";
- gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc1";
- default-state = "off";
- };
-
- led4 {
- label = "green:user3";
- gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "none";
- default-state = "off";
- panic-indicator;
- };
- };
-
- sd_switch: regulator-sd_switch {
- compatible = "regulator-gpio";
- regulator-name = "sd_switch";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2900000>;
- regulator-type = "voltage";
- regulator-always-on;
-
- gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
- gpios-states = <0>;
- states = <1800000 0x1>,
- <2900000 0x0>;
- };
-
- sound {
- compatible = "audio-graph-card";
- label = "STM32MP1-AV96-HDMI";
- dais = <&sai2a_port>;
- status = "okay";
- };
-
- /* Enpirion EP3A8LQI U2 on the DHCOR */
- vdd_io: regulator-buck-io {
- compatible = "regulator-fixed";
- regulator-name = "buck-io";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- vin-supply = <&vdd>;
- };
-
- wlan_pwr: regulator-wlan {
- compatible = "regulator-fixed";
-
- regulator-name = "wl-reg";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-};
-
-&adc {
- pinctrl-names = "default";
- pinctrl-0 = <&adc12_ain_pins_b>;
- vdd-supply = <&vdd>;
- vdda-supply = <&vdda>;
- vref-supply = <&vdda>;
- status = "okay";
-
- adc1: adc@0 {
- st,adc-channels = <0 1 6>;
- st,min-sample-time-nsecs = <5000>;
- status = "okay";
- };
-
- adc2: adc@100 {
- st,adc-channels = <0 1 2>;
- st,min-sample-time-nsecs = <5000>;
- status = "okay";
- };
-};
-
-ðernet0 {
- status = "okay";
- pinctrl-0 = <ðernet0_rgmii_pins_c>;
- pinctrl-1 = <ðernet0_rgmii_sleep_pins_c>;
- pinctrl-names = "default", "sleep";
- phy-mode = "rgmii";
- max-speed = <1000>;
- phy-handle = <&phy0>;
-
- mdio0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "snps,dwmac-mdio";
- reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
- reset-delay-us = <1000>;
-
- phy0: ethernet-phy@7 {
- reg = <7>;
-
- rxc-skew-ps = <1500>;
- rxdv-skew-ps = <540>;
- rxd0-skew-ps = <420>;
- rxd1-skew-ps = <420>;
- rxd2-skew-ps = <420>;
- rxd3-skew-ps = <420>;
-
- txc-skew-ps = <1440>;
- txen-skew-ps = <540>;
- txd0-skew-ps = <420>;
- txd1-skew-ps = <420>;
- txd2-skew-ps = <420>;
- txd3-skew-ps = <420>;
- };
- };
-};
-
-&i2c1 { /* X6 I2C1 */
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_b>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&i2c2 { /* X6 I2C2 */
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_c>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&i2c4 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c4_pins_a>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /delete-property/dmas;
- /delete-property/dma-names;
-
- pmic: stpmic@33 {
- compatible = "st,stpmic1";
- reg = <0x33>;
- interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
- interrupt-controller;
- #interrupt-cells = <2>;
- status = "okay";
-
- regulators {
- compatible = "st,stpmic1-regulators";
-
- ldo1-supply = <&v3v3>;
- ldo2-supply = <&v3v3>;
- ldo3-supply = <&vdd_ddr>;
- ldo5-supply = <&v3v3>;
- ldo6-supply = <&v3v3>;
- pwr_sw1-supply = <&bst_out>;
- pwr_sw2-supply = <&bst_out>;
-
- vddcore: buck1 {
- regulator-name = "vddcore";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd_ddr: buck2 {
- regulator-name = "vdd_ddr";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd: buck3 {
- regulator-name = "vdd";
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- v3v3: buck4 {
- regulator-name = "v3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-over-current-protection;
- regulator-initial-mode = <0>;
- };
-
- vdda: ldo1 {
- regulator-name = "vdda";
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- interrupts = <IT_CURLIM_LDO1 0>;
- };
-
- v2v8: ldo2 {
- regulator-name = "v2v8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- interrupts = <IT_CURLIM_LDO2 0>;
- };
-
- vtt_ddr: ldo3 {
- regulator-name = "vtt_ddr";
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <750000>;
- regulator-always-on;
- regulator-over-current-protection;
- };
-
- vdd_usb: ldo4 {
- regulator-name = "vdd_usb";
- interrupts = <IT_CURLIM_LDO4 0>;
- };
-
- vdd_sd: ldo5 {
- regulator-name = "vdd_sd";
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- interrupts = <IT_CURLIM_LDO5 0>;
- regulator-boot-on;
- };
-
- v1v8: ldo6 {
- regulator-name = "v1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- interrupts = <IT_CURLIM_LDO6 0>;
- regulator-enable-ramp-delay = <300000>;
- };
-
- vref_ddr: vref_ddr {
- regulator-name = "vref_ddr";
- regulator-always-on;
- };
-
- bst_out: boost {
- regulator-name = "bst_out";
- interrupts = <IT_OCP_BOOST 0>;
- };
-
- vbus_otg: pwr_sw1 {
- regulator-name = "vbus_otg";
- interrupts = <IT_OCP_OTG 0>;
- regulator-active-discharge = <1>;
- };
-
- vbus_sw: pwr_sw2 {
- regulator-name = "vbus_sw";
- interrupts = <IT_OCP_SWOUT 0>;
- regulator-active-discharge = <1>;
- };
- };
-
- onkey {
- compatible = "st,stpmic1-onkey";
- interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
- interrupt-names = "onkey-falling", "onkey-rising";
- status = "okay";
- };
-
- watchdog {
- compatible = "st,stpmic1-wdt";
- status = "disabled";
- };
- };
-
- hdmi-transmitter@3d {
- compatible = "adi,adv7513";
- reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>;
- reg-names = "main", "cec", "edid", "packet";
- clocks = <&cec_clock>;
- clock-names = "cec";
-
- avdd-supply = <&v3v3>;
- dvdd-supply = <&v3v3>;
- pvdd-supply = <&v3v3>;
- dvdd-3v-supply = <&v3v3>;
- bgvdd-supply = <&v3v3>;
-
- interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
- interrupt-parent = <&gpiog>;
-
- status = "okay";
-
- adi,input-depth = <8>;
- adi,input-colorspace = "rgb";
- adi,input-clock = "1x";
- adi,input-style = <1>;
- adi,input-justification = "evenly";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7513_in: endpoint {
- remote-endpoint = <<dc_ep0_out>;
- };
- };
-
- port@1 {
- reg = <1>;
- adv7513_out: endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
-
- port@2 {
- reg = <2>;
- adv7513_i2s0: endpoint {
- remote-endpoint = <&sai2a_endpoint>;
- };
- };
- };
- };
-
- eeprom@53 {
- compatible = "atmel,24c02";
- reg = <0x53>;
- pagesize = <16>;
- };
-};
-
-&iwdg2 {
- timeout-sec = <32>;
- status = "okay";
-};
-
-<dc {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <<dc_pins_d>;
- pinctrl-1 = <<dc_sleep_pins_d>;
- status = "okay";
-
- port {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ltdc_ep0_out: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&adv7513_in>;
- };
- };
-};
-
-&m_can1 {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&m_can1_pins_b>;
- pinctrl-1 = <&m_can1_sleep_pins_b>;
- status = "disabled";
-};
-
-&m_can2 {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&m_can2_pins_a>;
- pinctrl-1 = <&m_can2_sleep_pins_a>;
- status = "disabled";
-};
-
-&pwr_regulators {
- vdd-supply = <&vdd_io>;
- vdd_3v3_usbfs-supply = <&vdd_usb>;
-};
-
-&qspi {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
- pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
- reg = <0x58003000 0x1000>, <0x70000000 0x200000>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- flash0: spi-flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-rx-bus-width = <4>;
- spi-max-frequency = <108000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- };
-};
-
-&rng1 {
- status = "okay";
-};
-
-&rtc {
- status = "okay";
-};
-
-&sai2 {
- clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sai2a_pins_c>;
- pinctrl-1 = <&sai2a_sleep_pins_c>;
- clock-names = "pclk", "x8k", "x11k";
- status = "okay";
-
- sai2a: audio-controller@4400b004 {
- #clock-cells = <0>;
- dma-names = "tx";
- clocks = <&rcc SAI2_K>;
- clock-names = "sai_ck";
- status = "okay";
-
- sai2a_port: port {
- sai2a_endpoint: endpoint {
- remote-endpoint = <&adv7513_i2s0>;
- format = "i2s";
- mclk-fs = <256>;
- };
- };
- };
-};
-
-&sdmmc1 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
- pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
- pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
- cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
- disable-wp;
- st,sig-dir;
- st,neg-edge;
- st,use-ckin;
- bus-width = <4>;
- vmmc-supply = <&vdd_sd>;
- vqmmc-supply = <&sd_switch>;
- status = "okay";
-};
-
-&sdmmc2 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
- pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
- pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
- bus-width = <8>;
- mmc-ddr-1_8v;
- no-sd;
- no-sdio;
- non-removable;
- st,neg-edge;
- vmmc-supply = <&v3v3>;
- vqmmc-supply = <&vdd_io>;
- status = "okay";
-};
-
-&sdmmc3 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc3_b4_pins_b>;
- pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
- pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
- broken-cd;
- non-removable;
- st,neg-edge;
- bus-width = <4>;
- vmmc-supply = <&wlan_pwr>;
- status = "okay";
-
- #address-cells = <1>;
- #size-cells = <0>;
- brcmf: bcrmf@1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- };
-};
-
-&spi2 {
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- cs-gpios = <&gpioi 0 0>;
- status = "disabled";
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&uart4 {
- /* On Low speed expansion header */
- label = "LS-UART1";
- pinctrl-names = "default";
- pinctrl-0 = <&uart4_pins_b>;
- status = "okay";
-};
-
-&uart7 {
- /* On Low speed expansion header */
- label = "LS-UART0";
- pinctrl-names = "default";
- pinctrl-0 = <&uart7_pins_a>;
- status = "okay";
-};
-
-/* Bluetooth */
-&usart2 {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&usart2_pins_a>;
- pinctrl-1 = <&usart2_sleep_pins_a>;
- st,hw-flow-ctrl;
- status = "okay";
-
- bluetooth {
- compatible = "brcm,bcm43438-bt";
- max-speed = <3000000>;
- shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
- };
-};
-
-&usbh_ehci {
- phys = <&usbphyc_port0>;
- phy-names = "usb";
- status = "okay";
-};
-
-&usbotg_hs {
- pinctrl-0 = <&usbotg_hs_pins_a>;
- pinctrl-names = "default";
- phy-names = "usb2-phy";
- phys = <&usbphyc_port1 0>;
- status = "okay";
- vbus-supply = <&vbus_otg>;
-};
-
-&usbphyc {
- status = "okay";
-};
-
-&usbphyc_port0 {
- phy-supply = <&vdd_usb>;
- vdda1v1-supply = <®11>;
- vdda1v8-supply = <®18>;
-};
-
-&usbphyc_port1 {
- phy-supply = <&vdd_usb>;
- vdda1v1-supply = <®11>;
- vdda1v8-supply = <®18>;
-};
+/* This DT is here only for backward compatibility */
+#include "stm32mp157a-dhcor-avenger96.dts"
diff --git a/arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts
new file mode 100644
index 000000000000..010baa7f8afa
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+
+#include "stm32mp157a-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-avenger96.dtsi"
+
+/ {
+ model = "Arrow Electronics STM32MP157A Avenger96 board";
+ compatible = "arrow,stm32mp157a-avenger96", "dh,stm32mp157a-dhcor-som",
+ "st,stm32mp157";
+};
+
+&m_can1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&m_can1_pins_b>;
+ pinctrl-1 = <&m_can1_sleep_pins_b>;
+ status = "disabled";
+};
+
+&m_can2 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&m_can2_pins_a>;
+ pinctrl-1 = <&m_can2_sleep_pins_a>;
+ status = "disabled";
+};
diff --git a/arch/arm/boot/dts/stm32mp157a-dhcor-som.dtsi b/arch/arm/boot/dts/stm32mp157a-dhcor-som.dtsi
new file mode 100644
index 000000000000..41428381e19c
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157a-dhcor-som.dtsi
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+
+/ {
+ model = "DH Electronics STM32MP157A DHCOR SoM";
+ compatible = "dh,stm32mp157a-dhcor-som", "st,stm32mp157";
+};
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
new file mode 100644
index 000000000000..930202742a3f
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
@@ -0,0 +1,401 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+/* Avenger96 uses DHCOR SoM configured for 1V8 IO operation */
+#include "stm32mp15xx-dhcor-io1v8.dtsi"
+
+/ {
+ aliases {
+ ethernet0 = ðernet0;
+ mmc0 = &sdmmc1;
+ serial0 = &uart4;
+ serial1 = &uart7;
+ serial2 = &usart2;
+ spi0 = &qspi;
+ };
+
+ /* XTal Q1 */
+ cec_clock: clk-cec-fixed {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <&adv7513_out>;
+ };
+ };
+ };
+
+ led {
+ compatible = "gpio-leds";
+ led1 {
+ label = "green:user0";
+ gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+
+ led2 {
+ label = "green:user1";
+ gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ default-state = "off";
+ };
+
+ led3 {
+ label = "green:user2";
+ gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc1";
+ default-state = "off";
+ };
+
+ led4 {
+ label = "green:user3";
+ gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "none";
+ default-state = "off";
+ panic-indicator;
+ };
+ };
+
+ sd_switch: regulator-sd_switch {
+ compatible = "regulator-gpio";
+ regulator-name = "sd_switch";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2900000>;
+ regulator-type = "voltage";
+ regulator-always-on;
+
+ gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+ states = <1800000 0x1>,
+ <2900000 0x0>;
+ };
+
+ sound {
+ compatible = "audio-graph-card";
+ label = "STM32MP1-AV96-HDMI";
+ dais = <&sai2a_port>;
+ status = "okay";
+ };
+
+ wlan_pwr: regulator-wlan {
+ compatible = "regulator-fixed";
+
+ regulator-name = "wl-reg";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&adc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&adc12_ain_pins_b>;
+ vdd-supply = <&vdd>;
+ vdda-supply = <&vdda>;
+ vref-supply = <&vdda>;
+ status = "okay";
+
+ adc1: adc@0 {
+ st,adc-channels = <0 1 6>;
+ st,min-sample-time-nsecs = <5000>;
+ status = "okay";
+ };
+
+ adc2: adc@100 {
+ st,adc-channels = <0 1 2>;
+ st,min-sample-time-nsecs = <5000>;
+ status = "okay";
+ };
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rgmii_pins_c>;
+ pinctrl-1 = <ðernet0_rgmii_sleep_pins_c>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii";
+ max-speed = <1000>;
+ phy-handle = <&phy0>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <1000>;
+
+ phy0: ethernet-phy@7 {
+ reg = <7>;
+
+ rxc-skew-ps = <1500>;
+ rxdv-skew-ps = <540>;
+ rxd0-skew-ps = <420>;
+ rxd1-skew-ps = <420>;
+ rxd2-skew-ps = <420>;
+ rxd3-skew-ps = <420>;
+
+ txc-skew-ps = <1440>;
+ txen-skew-ps = <540>;
+ txd0-skew-ps = <420>;
+ txd1-skew-ps = <420>;
+ txd2-skew-ps = <420>;
+ txd3-skew-ps = <420>;
+ };
+ };
+};
+
+&i2c1 { /* X6 I2C1 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_b>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+};
+
+&i2c2 { /* X6 I2C2 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_c>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+};
+
+&i2c4 {
+ hdmi-transmitter@3d {
+ compatible = "adi,adv7513";
+ reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>;
+ reg-names = "main", "cec", "edid", "packet";
+ clocks = <&cec_clock>;
+ clock-names = "cec";
+
+ avdd-supply = <&v3v3>;
+ dvdd-supply = <&v3v3>;
+ pvdd-supply = <&v3v3>;
+ dvdd-3v-supply = <&v3v3>;
+ bgvdd-supply = <&v3v3>;
+
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-parent = <&gpiog>;
+
+ status = "okay";
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7513_in: endpoint {
+ remote-endpoint = <<dc_ep0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7513_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ adv7513_i2s0: endpoint {
+ remote-endpoint = <&sai2a_endpoint>;
+ };
+ };
+ };
+ };
+};
+
+<dc {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <<dc_pins_d>;
+ pinctrl-1 = <<dc_sleep_pins_d>;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ltdc_ep0_out: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&adv7513_in>;
+ };
+ };
+};
+
+&sai2 {
+ clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sai2a_pins_c>;
+ pinctrl-1 = <&sai2a_sleep_pins_c>;
+ clock-names = "pclk", "x8k", "x11k";
+ status = "okay";
+
+ sai2a: audio-controller@4400b004 {
+ #clock-cells = <0>;
+ dma-names = "tx";
+ clocks = <&rcc SAI2_K>;
+ clock-names = "sai_ck";
+ status = "okay";
+
+ sai2a_port: port {
+ sai2a_endpoint: endpoint {
+ remote-endpoint = <&adv7513_i2s0>;
+ format = "i2s";
+ mclk-fs = <256>;
+ };
+ };
+ };
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
+ cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ disable-wp;
+ st,sig-dir;
+ st,neg-edge;
+ st,use-ckin;
+ bus-width = <4>;
+ vmmc-supply = <&vdd_sd>;
+ vqmmc-supply = <&sd_switch>;
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ no-sd;
+ no-sdio;
+ non-removable;
+ st,neg-edge;
+ vmmc-supply = <&v3v3>;
+ vqmmc-supply = <&vdd_io>;
+ status = "okay";
+};
+
+&sdmmc3 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc3_b4_pins_b>;
+ pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
+ pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
+ broken-cd;
+ non-removable;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&wlan_pwr>;
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+&spi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ cs-gpios = <&gpioi 0 0>;
+ status = "disabled";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+};
+
+&uart4 {
+ /* On Low speed expansion header */
+ label = "LS-UART1";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_b>;
+ status = "okay";
+};
+
+&uart7 {
+ /* On Low speed expansion header */
+ label = "LS-UART0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7_pins_a>;
+ status = "okay";
+};
+
+/* Bluetooth */
+&usart2 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&usart2_pins_a>;
+ pinctrl-1 = <&usart2_sleep_pins_a>;
+ st,hw-flow-ctrl;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <3000000>;
+ shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&usbh_ehci {
+ phys = <&usbphyc_port0>;
+ phy-names = "usb";
+ status = "okay";
+};
+
+&usbotg_hs {
+ pinctrl-0 = <&usbotg_hs_pins_a>;
+ pinctrl-names = "default";
+ phy-names = "usb2-phy";
+ phys = <&usbphyc_port1 0>;
+ status = "okay";
+ vbus-supply = <&vbus_otg>;
+};
+
+&usbphyc {
+ status = "okay";
+};
+
+&usbphyc_port0 {
+ phy-supply = <&vdd_usb>;
+ vdda1v1-supply = <®11>;
+ vdda1v8-supply = <®18>;
+};
+
+&usbphyc_port1 {
+ phy-supply = <&vdd_usb>;
+ vdda1v1-supply = <®11>;
+ vdda1v8-supply = <®18>;
+};
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi
new file mode 100644
index 000000000000..75172314d7af
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+/ {
+ /* Enpirion EP3A8LQI U2 on the DHCOR */
+ vdd_io: regulator-buck-io {
+ compatible = "regulator-fixed";
+ regulator-name = "buck-io";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vdd>;
+ };
+};
+
+&pwr_regulators {
+ vdd-supply = <&vdd_io>;
+};
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
new file mode 100644
index 000000000000..04fbb324a541
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
@@ -0,0 +1,209 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+ aliases {
+ spi0 = &qspi;
+ };
+
+ memory@c0000000 {
+ device_type = "memory";
+ reg = <0xc0000000 0x40000000>;
+ };
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pmic: stpmic@33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ status = "okay";
+
+ regulators {
+ compatible = "st,stpmic1-regulators";
+
+ ldo1-supply = <&v3v3>;
+ ldo2-supply = <&v3v3>;
+ ldo3-supply = <&vdd_ddr>;
+ ldo5-supply = <&v3v3>;
+ ldo6-supply = <&v3v3>;
+ pwr_sw1-supply = <&bst_out>;
+ pwr_sw2-supply = <&bst_out>;
+
+ vddcore: buck1 {
+ regulator-name = "vddcore";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd_ddr: buck2 {
+ regulator-name = "vdd_ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd: buck3 {
+ regulator-name = "vdd";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ v3v3: buck4 {
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ regulator-initial-mode = <0>;
+ };
+
+ vdda: ldo1 {
+ regulator-name = "vdda";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO1 0>;
+ };
+
+ v2v8: ldo2 {
+ regulator-name = "v2v8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ interrupts = <IT_CURLIM_LDO2 0>;
+ };
+
+ vtt_ddr: ldo3 {
+ regulator-name = "vtt_ddr";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <750000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ vdd_usb: ldo4 {
+ regulator-name = "vdd_usb";
+ interrupts = <IT_CURLIM_LDO4 0>;
+ };
+
+ vdd_sd: ldo5 {
+ regulator-name = "vdd_sd";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO5 0>;
+ regulator-boot-on;
+ };
+
+ v1v8: ldo6 {
+ regulator-name = "v1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ interrupts = <IT_CURLIM_LDO6 0>;
+ regulator-enable-ramp-delay = <300000>;
+ };
+
+ vref_ddr: vref_ddr {
+ regulator-name = "vref_ddr";
+ regulator-always-on;
+ };
+
+ bst_out: boost {
+ regulator-name = "bst_out";
+ interrupts = <IT_OCP_BOOST 0>;
+ };
+
+ vbus_otg: pwr_sw1 {
+ regulator-name = "vbus_otg";
+ interrupts = <IT_OCP_OTG 0>;
+ regulator-active-discharge = <1>;
+ };
+
+ vbus_sw: pwr_sw2 {
+ regulator-name = "vbus_sw";
+ interrupts = <IT_OCP_SWOUT 0>;
+ regulator-active-discharge = <1>;
+ };
+ };
+
+ onkey {
+ compatible = "st,stpmic1-onkey";
+ interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+ interrupt-names = "onkey-falling", "onkey-rising";
+ status = "okay";
+ };
+
+ watchdog {
+ compatible = "st,stpmic1-wdt";
+ status = "disabled";
+ };
+ };
+
+ eeprom@53 {
+ compatible = "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+};
+
+&iwdg2 {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&pwr_regulators {
+ vdd-supply = <&vdd>;
+ vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+ pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+ reg = <0x58003000 0x1000>, <0x70000000 0x200000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ flash0: spi-flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&rng1 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 4+ messages in thread