* [PATCH v3 1/2] dt-bindings: fsl: add kamstrup flex concentrator to schema @ 2020-09-23 15:40 Bruno Thomsen 2020-09-23 15:40 ` [PATCH v3 2/2] ARM: dts: imx7: add support for kamstrup flex concentrator Bruno Thomsen 0 siblings, 1 reply; 3+ messages in thread From: Bruno Thomsen @ 2020-09-23 15:40 UTC (permalink / raw) To: linux-kernel, linux-arm-kernel, devicetree Cc: Rob Herring, Shawn Guo, Bruno Thomsen, bth, NXP Linux Team, Pengutronix Kernel Team, Fabio Estevam Add Kamstrup OMNIA Flex Concentrator compatibles to the schema so we can make use of them for the validation. Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> Acked-by: Rob Herring <robh@kernel.org> --- No changes since version 2. Changes since version 1: - Patch prefix renamed to "dt-bindings: fsl:" - Added acked-by from Rob Herring. - Fixed typo in commit message. Documentation/devicetree/bindings/arm/fsl.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 6da9d734cdb7..8e9be78f3d68 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -304,6 +304,8 @@ properties: - enum: - fsl,imx7d-sdb # i.MX7 SabreSD Board - fsl,imx7d-sdb-reva # i.MX7 SabreSD Rev-A Board + - kam,imx7d-flex-concentrator # Kamstrup OMNIA Flex Concentrator + - kam,imx7d-flex-concentrator-mfg # Kamstrup OMNIA Flex Concentrator in manufacturing mode - novtech,imx7d-meerkat96 # i.MX7 Meerkat96 Board - technexion,imx7d-pico-dwarf # TechNexion i.MX7D Pico-Dwarf - technexion,imx7d-pico-hobbit # TechNexion i.MX7D Pico-Hobbit base-commit: 805c6d3c19210c90c109107d189744e960eae025 -- 2.26.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH v3 2/2] ARM: dts: imx7: add support for kamstrup flex concentrator 2020-09-23 15:40 [PATCH v3 1/2] dt-bindings: fsl: add kamstrup flex concentrator to schema Bruno Thomsen @ 2020-09-23 15:40 ` Bruno Thomsen 2020-10-28 12:40 ` Shawn Guo 0 siblings, 1 reply; 3+ messages in thread From: Bruno Thomsen @ 2020-09-23 15:40 UTC (permalink / raw) To: linux-kernel, linux-arm-kernel, devicetree Cc: Shawn Guo, Bruno Thomsen, bth, NXP Linux Team, Pengutronix Kernel Team, Fabio Estevam This adds support for the OMNIA Flex Concentrator product from Kamstrup A/S. It's providing radio mesh communication infrastructure for smart electricity meters. Kamstrup OMNIA is a modular and scalable smart grid platform. Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> --- Changes since version 2: - Found root cause of Ethernet PHY auto detect issue and created a mdio patch series that resolves the issue. https://lore.kernel.org/netdev/20200730195749.4922-1-bruno.thomsen@gmail.com/ - Ethernet PHY reset is using new MDIO bus reset. - Ethernet PHY interrupt added. - Removed SION from a few GPIOs used for Ethernet PHY. Changes since version 1: - Sorted labeling nodes. - Sorted pinctrl entries. - Removed deprecated fec phy reset properties. - Added mdio phy reset properties. - Disabled phy type auto detection and added note to commit message. - Fixed two comment typos. arch/arm/boot/dts/Makefile | 2 + .../boot/dts/imx7d-flex-concentrator-mfg.dts | 25 ++ arch/arm/boot/dts/imx7d-flex-concentrator.dts | 319 ++++++++++++++++++ 3 files changed, 346 insertions(+) create mode 100644 arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts create mode 100644 arch/arm/boot/dts/imx7d-flex-concentrator.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 4572db3fa5ae..15be5a2fe831 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -634,6 +634,8 @@ dtb-$(CONFIG_SOC_IMX7D) += \ imx7d-colibri-emmc-aster.dtb \ imx7d-colibri-emmc-eval-v3.dtb \ imx7d-colibri-eval-v3.dtb \ + imx7d-flex-concentrator.dtb \ + imx7d-flex-concentrator-mfg.dtb \ imx7d-mba7.dtb \ imx7d-meerkat96.dtb \ imx7d-nitrogen7.dtb \ diff --git a/arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts b/arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts new file mode 100644 index 000000000000..789f0837058f --- /dev/null +++ b/arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device Tree Source for Kamstrup OMNIA Flex Concentrator in + * manufacturing/debugging mode. + * + * Copyright (C) 2020 Kamstrup A/S + * Author: Bruno Thomsen <bruno.thomsen@gmail.com> + */ + +/dts-v1/; + +#include "imx7d-flex-concentrator.dts" + +/ { + model = "Kamstrup OMNIA Flex Concentrator - Manufacturing"; + compatible = "kam,imx7d-flex-concentrator-mfg", "kam,imx7d-flex-concentrator", "fsl,imx7d"; + + chosen { + stdout-path = &uart4; + }; +}; + +&uart4 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx7d-flex-concentrator.dts b/arch/arm/boot/dts/imx7d-flex-concentrator.dts new file mode 100644 index 000000000000..9f73c79253cb --- /dev/null +++ b/arch/arm/boot/dts/imx7d-flex-concentrator.dts @@ -0,0 +1,319 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device Tree Source for Kamstrup OMNIA Flex Concentrator. + * + * Copyright (C) 2020 Kamstrup A/S + * Author: Bruno Thomsen <bruno.thomsen@gmail.com> + */ + +/dts-v1/; + +#include "imx7d-tqma7.dtsi" + +/* Some I2C devices on TQMa7 SoM are not mounted */ +/delete-node/ &m24c64; +/delete-node/ &ds1339; + +/ { + model = "Kamstrup OMNIA Flex Concentrator"; + compatible = "kam,imx7d-flex-concentrator", "fsl,imx7d"; + + memory@80000000 { + device_type = "memory"; + /* 1024 MB - TQMa7D board configuration */ + reg = <0x80000000 0x40000000>; + }; + + reg_usb_otg2_vbus: regulator-usb-otg2-vbus { + compatible = "regulator-fixed"; + regulator-name = "VBUS_USBOTG2"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_vref_1v8: regulator-vref-1v8 { + compatible = "regulator-fixed"; + regulator-name = "VCC1V8_REF"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + vin-supply = <&sw2_reg>; + }; + + /* + * Human Machine Interface consists of 4 dual red/green LEDs. + * hmi-a-green is controlled directly by the switch-mode power supply. + * hmi-a-red is not used. + */ + gpio-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + hmi-b-red { + label = "hmi-b:red:provisioning"; + gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + hmi-b-green { + label = "hmi-b:green:operation"; + gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + hmi-c-red { + label = "hmi-c:red:mesh-error"; + gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + hmi-c-green { + label = "hmi-c:green:mesh-activity"; + gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + hmi-d-red { + label = "hmi-d:red:wan-down"; + gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + hmi-d-green { + label = "hmi-d:green:ipsec-up"; + gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + /* + * Errata e10574 board restart workaround. + */ + gpio-restart { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_restart>; + compatible = "gpio-restart"; + gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; + priority = <200>; + }; +}; + +/* + * Analog signals + * ADC1_IN0: SMPS - 5V output monitor (voltage divider: 1/0.2806) + */ +&adc1 { + vref-supply = <®_vref_1v8>; + status = "okay"; +}; + +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + num-chipselects = <1>; + cs-gpios = <&gpio4 23 GPIO_ACTIVE_LOW>; + status = "okay"; + + pcf2127: rtc@0 { + compatible = "nxp,pcf2127"; + reg = <0>; + spi-max-frequency = <2000000>; + }; +}; + +&ecspi4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi4>; + num-chipselects = <1>; + cs-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>; + status = "okay"; + + /* + * ST chip maximum SPI clock frequency is 33 MHz. + * + * TCG specification - Section 6.4.1 Clocking: + * TPM shall support a SPI clock frequency range of 10-24 MHz. + */ + st33htph: tpm-tis@0 { + compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi"; + reg = <0>; + spi-max-frequency = <24000000>; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1>; + phy-mode = "rmii"; + phy-handle = <ðphy>; + status = "okay"; + + /* + * MDIO bus reset is used to generate PHY device reset before + * Ethernet PHY type ID auto-detection. Otherwise this communication + * fails as device does not answer when recommended reset circuit + * is used. + */ + mdio { + #address-cells = <1>; + #size-cells = <0>; + + reset-delay-us = <100000>; + reset-post-delay-us = <500000>; + reset-gpios = <&gpio7 15 GPIO_ACTIVE_LOW>; + + /* Microchip/Micrel KSZ8081RNB */ + ethphy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; + reg = <1>; + }; + }; +}; + +/* + * Detection signals for internal USB modules. + * Used for robust USB plug and play handling such as USB downstream port + * power-cycle and USB hub reset in case of misbehaving or crashed modules. + * + * SMPS - AC input monitor based on zero crossing. + * Used for last gasp notification. + */ +&gpio3 { + gpio-line-names = "", "", "", "", "", "", "", "", + "", "", "", "", "smps-ac-monitor", "", "usb-hub-reset", "", + "", "", "", "", "", "", "", "", + "", "module-b-detection", "", "module-a-detection", "", "", "", ""; +}; + +/* + * Tamper IRQ trigger timestamp reading. + * Used for sealed cover opened/closed notification. + */ +&gpio5 { + gpio-line-names = "", "", "", "", "", "", "", "", + "", "", "", "", "rtc-tamper-irq", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_misc>; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX7D_PAD_ECSPI2_MISO__ECSPI2_MISO 0x7c /* X2-15 */ + MX7D_PAD_ECSPI2_MOSI__ECSPI2_MOSI 0x74 /* X2-18 */ + MX7D_PAD_ECSPI2_SCLK__ECSPI2_SCLK 0x74 /* X2-13 */ + MX7D_PAD_ECSPI2_SS0__GPIO4_IO23 0x74 /* X2-20 */ + /* RTC - Tamper IRQ */ + MX7D_PAD_SD2_CLK__GPIO5_IO12 0x3c /* X1-92 */ + >; + }; + + pinctrl_ecspi4: ecspi4grp { + fsl,pins = < + MX7D_PAD_LCD_CLK__ECSPI4_MISO 0x7c /* X2-72 */ + MX7D_PAD_LCD_ENABLE__ECSPI4_MOSI 0x74 /* X2-68 */ + MX7D_PAD_LCD_HSYNC__ECSPI4_SCLK 0x74 /* X2-76 */ + MX7D_PAD_LCD_VSYNC__GPIO3_IO3 0x74 /* X2-78 */ + >; + }; + + pinctrl_enet1: enet1grp { + fsl,pins = < + MX7D_PAD_GPIO1_IO10__ENET1_MDIO 0x03 /* X2-48 */ + MX7D_PAD_GPIO1_IO11__ENET1_MDC 0x03 /* X2-46 */ + MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 0x71 /* X2-53 */ + MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 0x71 /* X2-55 */ + MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x71 /* X2-61 */ + MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 0x79 /* X2-56 */ + MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 0x79 /* X2-58 */ + MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x79 /* X2-64 */ + MX7D_PAD_ENET1_RGMII_RXC__ENET1_RX_ER 0x73 /* X2-52 */ + /* PHY reset: SRE_FAST, DSE_X1 */ + MX7D_PAD_ENET1_COL__GPIO7_IO15 0x00 /* X1-96 */ + /* Clock from PHY to MAC: 100kPU */ + MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1 0x70 /* X3-4 */ + /* PHY interrupt: 100kPU, HYS */ + MX7D_PAD_GPIO1_IO09__GPIO1_IO9 0x78 /* X1-80 */ + >; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = < + MX7D_PAD_LCD_DATA01__GPIO3_IO6 0x14 /* X2-82 */ + MX7D_PAD_EPDC_BDR0__GPIO2_IO28 0x14 /* X1-82 */ + MX7D_PAD_EPDC_BDR1__GPIO2_IO29 0x14 /* X1-84 */ + MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30 0x14 /* X1-86 */ + MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31 0x14 /* X1-88 */ + MX7D_PAD_UART2_TX_DATA__GPIO4_IO3 0x14 /* X1-90 */ + >; + }; + + pinctrl_misc: miscgrp { + fsl,pins = < + /* Module A detection (low = present) */ + MX7D_PAD_LCD_DATA22__GPIO3_IO27 0x7c /* X2-105 */ + /* Module B detection (low = present) */ + MX7D_PAD_LCD_DATA20__GPIO3_IO25 0x7c /* X2-103 */ + /* SMPS - AC input monitor (high = failure) */ + MX7D_PAD_LCD_DATA07__GPIO3_IO12 0x7c /* X2-88 */ + /* USB - Hub reset */ + MX7D_PAD_LCD_DATA09__GPIO3_IO14 0x74 /* X2-92 */ + >; + }; + + pinctrl_restart: restartgrp { + fsl,pins = < + MX7D_PAD_ENET1_TX_CLK__GPIO7_IO12 0x74 /* X1-94 */ + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX7D_PAD_SAI2_TX_SYNC__UART4_DCE_RX 0x7e /* X3-14 */ + MX7D_PAD_SAI2_TX_BCLK__UART4_DCE_TX 0x76 /* X3-16 */ + >; + }; +}; + +&iomuxc_lpsr { + pinctrl_usbotg2: usbotg2grp { + fsl,pins = < + MX7D_PAD_LPSR_GPIO1_IO06__USB_OTG2_OC 0x5c /* X3-11 */ + MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7 0x59 /* X3-9 */ + >; + }; + +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + assigned-clocks = <&clks IMX7D_UART4_ROOT_SRC>; + assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>; +}; + +&usbotg2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg2>; + vbus-supply = <®_usb_otg2_vbus>; + srp-disable; + hnp-disable; + adp-disable; + dr_mode = "host"; + status = "okay"; +}; + +/* + * External watchdog feature provided by pcf2127. + */ +&wdog1 { + status = "disabled"; +}; -- 2.26.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v3 2/2] ARM: dts: imx7: add support for kamstrup flex concentrator 2020-09-23 15:40 ` [PATCH v3 2/2] ARM: dts: imx7: add support for kamstrup flex concentrator Bruno Thomsen @ 2020-10-28 12:40 ` Shawn Guo 0 siblings, 0 replies; 3+ messages in thread From: Shawn Guo @ 2020-10-28 12:40 UTC (permalink / raw) To: Bruno Thomsen Cc: devicetree, linux-kernel, bth, NXP Linux Team, Pengutronix Kernel Team, Fabio Estevam, linux-arm-kernel On Wed, Sep 23, 2020 at 05:40:24PM +0200, Bruno Thomsen wrote: > This adds support for the OMNIA Flex Concentrator product > from Kamstrup A/S. It's providing radio mesh communication > infrastructure for smart electricity meters. > > Kamstrup OMNIA is a modular and scalable smart grid platform. > > Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> > --- > Changes since version 2: > - Found root cause of Ethernet PHY auto detect issue and created > a mdio patch series that resolves the issue. > https://lore.kernel.org/netdev/20200730195749.4922-1-bruno.thomsen@gmail.com/ > - Ethernet PHY reset is using new MDIO bus reset. > - Ethernet PHY interrupt added. > - Removed SION from a few GPIOs used for Ethernet PHY. > > Changes since version 1: > - Sorted labeling nodes. > - Sorted pinctrl entries. > - Removed deprecated fec phy reset properties. > - Added mdio phy reset properties. > - Disabled phy type auto detection and added note to commit message. > - Fixed two comment typos. > > arch/arm/boot/dts/Makefile | 2 + > .../boot/dts/imx7d-flex-concentrator-mfg.dts | 25 ++ > arch/arm/boot/dts/imx7d-flex-concentrator.dts | 319 ++++++++++++++++++ > 3 files changed, 346 insertions(+) > create mode 100644 arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts > create mode 100644 arch/arm/boot/dts/imx7d-flex-concentrator.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 4572db3fa5ae..15be5a2fe831 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -634,6 +634,8 @@ dtb-$(CONFIG_SOC_IMX7D) += \ > imx7d-colibri-emmc-aster.dtb \ > imx7d-colibri-emmc-eval-v3.dtb \ > imx7d-colibri-eval-v3.dtb \ > + imx7d-flex-concentrator.dtb \ > + imx7d-flex-concentrator-mfg.dtb \ > imx7d-mba7.dtb \ > imx7d-meerkat96.dtb \ > imx7d-nitrogen7.dtb \ > diff --git a/arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts b/arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts > new file mode 100644 > index 000000000000..789f0837058f > --- /dev/null > +++ b/arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts > @@ -0,0 +1,25 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Device Tree Source for Kamstrup OMNIA Flex Concentrator in > + * manufacturing/debugging mode. > + * > + * Copyright (C) 2020 Kamstrup A/S > + * Author: Bruno Thomsen <bruno.thomsen@gmail.com> > + */ > + > +/dts-v1/; > + > +#include "imx7d-flex-concentrator.dts" > + > +/ { > + model = "Kamstrup OMNIA Flex Concentrator - Manufacturing"; > + compatible = "kam,imx7d-flex-concentrator-mfg", "kam,imx7d-flex-concentrator", "fsl,imx7d"; 'make dtbs_check' reports the following issue: compatible: ['kam,imx7d-flex-concentrator-mfg', 'kam,imx7d-flex-concentrator', 'fsl,imx7d'] is too long I think dropping 'kam,imx7d-flex-concentrator' should fix it. > + > + chosen { > + stdout-path = &uart4; > + }; > +}; > + > +&uart4 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/imx7d-flex-concentrator.dts b/arch/arm/boot/dts/imx7d-flex-concentrator.dts > new file mode 100644 > index 000000000000..9f73c79253cb > --- /dev/null > +++ b/arch/arm/boot/dts/imx7d-flex-concentrator.dts > @@ -0,0 +1,319 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Device Tree Source for Kamstrup OMNIA Flex Concentrator. > + * > + * Copyright (C) 2020 Kamstrup A/S > + * Author: Bruno Thomsen <bruno.thomsen@gmail.com> > + */ > + > +/dts-v1/; > + > +#include "imx7d-tqma7.dtsi" > + > +/* Some I2C devices on TQMa7 SoM are not mounted */ > +/delete-node/ &m24c64; > +/delete-node/ &ds1339; > + > +/ { > + model = "Kamstrup OMNIA Flex Concentrator"; > + compatible = "kam,imx7d-flex-concentrator", "fsl,imx7d"; > + > + memory@80000000 { > + device_type = "memory"; > + /* 1024 MB - TQMa7D board configuration */ > + reg = <0x80000000 0x40000000>; > + }; > + > + reg_usb_otg2_vbus: regulator-usb-otg2-vbus { > + compatible = "regulator-fixed"; > + regulator-name = "VBUS_USBOTG2"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_vref_1v8: regulator-vref-1v8 { > + compatible = "regulator-fixed"; > + regulator-name = "VCC1V8_REF"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + vin-supply = <&sw2_reg>; > + }; > + > + /* > + * Human Machine Interface consists of 4 dual red/green LEDs. > + * hmi-a-green is controlled directly by the switch-mode power supply. > + * hmi-a-red is not used. > + */ > + gpio-leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_leds>; > + > + hmi-b-red { gpio-leds: 'hmi-b-green', 'hmi-b-red', 'hmi-c-green', 'hmi-c-red', 'hmi-d-green', 'hmi-d-red' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' From schema: Documentation/devicetree/bindings/leds/leds-gpio.yaml Shawn > + label = "hmi-b:red:provisioning"; > + gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + > + hmi-b-green { > + label = "hmi-b:green:operation"; > + gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + > + hmi-c-red { > + label = "hmi-c:red:mesh-error"; > + gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + > + hmi-c-green { > + label = "hmi-c:green:mesh-activity"; > + gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + > + hmi-d-red { > + label = "hmi-d:red:wan-down"; > + gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + > + hmi-d-green { > + label = "hmi-d:green:ipsec-up"; > + gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + }; > + > + /* > + * Errata e10574 board restart workaround. > + */ > + gpio-restart { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_restart>; > + compatible = "gpio-restart"; > + gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; > + priority = <200>; > + }; > +}; > + > +/* > + * Analog signals > + * ADC1_IN0: SMPS - 5V output monitor (voltage divider: 1/0.2806) > + */ > +&adc1 { > + vref-supply = <®_vref_1v8>; > + status = "okay"; > +}; > + > +&ecspi2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ecspi2>; > + num-chipselects = <1>; > + cs-gpios = <&gpio4 23 GPIO_ACTIVE_LOW>; > + status = "okay"; > + > + pcf2127: rtc@0 { > + compatible = "nxp,pcf2127"; > + reg = <0>; > + spi-max-frequency = <2000000>; > + }; > +}; > + > +&ecspi4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ecspi4>; > + num-chipselects = <1>; > + cs-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>; > + status = "okay"; > + > + /* > + * ST chip maximum SPI clock frequency is 33 MHz. > + * > + * TCG specification - Section 6.4.1 Clocking: > + * TPM shall support a SPI clock frequency range of 10-24 MHz. > + */ > + st33htph: tpm-tis@0 { > + compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi"; > + reg = <0>; > + spi-max-frequency = <24000000>; > + }; > +}; > + > +&fec1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_enet1>; > + phy-mode = "rmii"; > + phy-handle = <ðphy>; > + status = "okay"; > + > + /* > + * MDIO bus reset is used to generate PHY device reset before > + * Ethernet PHY type ID auto-detection. Otherwise this communication > + * fails as device does not answer when recommended reset circuit > + * is used. > + */ > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + reset-delay-us = <100000>; > + reset-post-delay-us = <500000>; > + reset-gpios = <&gpio7 15 GPIO_ACTIVE_LOW>; > + > + /* Microchip/Micrel KSZ8081RNB */ > + ethphy: ethernet-phy@1 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + interrupt-parent = <&gpio1>; > + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; > + reg = <1>; > + }; > + }; > +}; > + > +/* > + * Detection signals for internal USB modules. > + * Used for robust USB plug and play handling such as USB downstream port > + * power-cycle and USB hub reset in case of misbehaving or crashed modules. > + * > + * SMPS - AC input monitor based on zero crossing. > + * Used for last gasp notification. > + */ > +&gpio3 { > + gpio-line-names = "", "", "", "", "", "", "", "", > + "", "", "", "", "smps-ac-monitor", "", "usb-hub-reset", "", > + "", "", "", "", "", "", "", "", > + "", "module-b-detection", "", "module-a-detection", "", "", "", ""; > +}; > + > +/* > + * Tamper IRQ trigger timestamp reading. > + * Used for sealed cover opened/closed notification. > + */ > +&gpio5 { > + gpio-line-names = "", "", "", "", "", "", "", "", > + "", "", "", "", "rtc-tamper-irq", "", "", "", > + "", "", "", "", "", "", "", "", > + "", "", "", "", "", "", "", ""; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_misc>; > + > + pinctrl_ecspi2: ecspi2grp { > + fsl,pins = < > + MX7D_PAD_ECSPI2_MISO__ECSPI2_MISO 0x7c /* X2-15 */ > + MX7D_PAD_ECSPI2_MOSI__ECSPI2_MOSI 0x74 /* X2-18 */ > + MX7D_PAD_ECSPI2_SCLK__ECSPI2_SCLK 0x74 /* X2-13 */ > + MX7D_PAD_ECSPI2_SS0__GPIO4_IO23 0x74 /* X2-20 */ > + /* RTC - Tamper IRQ */ > + MX7D_PAD_SD2_CLK__GPIO5_IO12 0x3c /* X1-92 */ > + >; > + }; > + > + pinctrl_ecspi4: ecspi4grp { > + fsl,pins = < > + MX7D_PAD_LCD_CLK__ECSPI4_MISO 0x7c /* X2-72 */ > + MX7D_PAD_LCD_ENABLE__ECSPI4_MOSI 0x74 /* X2-68 */ > + MX7D_PAD_LCD_HSYNC__ECSPI4_SCLK 0x74 /* X2-76 */ > + MX7D_PAD_LCD_VSYNC__GPIO3_IO3 0x74 /* X2-78 */ > + >; > + }; > + > + pinctrl_enet1: enet1grp { > + fsl,pins = < > + MX7D_PAD_GPIO1_IO10__ENET1_MDIO 0x03 /* X2-48 */ > + MX7D_PAD_GPIO1_IO11__ENET1_MDC 0x03 /* X2-46 */ > + MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 0x71 /* X2-53 */ > + MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 0x71 /* X2-55 */ > + MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x71 /* X2-61 */ > + MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 0x79 /* X2-56 */ > + MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 0x79 /* X2-58 */ > + MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x79 /* X2-64 */ > + MX7D_PAD_ENET1_RGMII_RXC__ENET1_RX_ER 0x73 /* X2-52 */ > + /* PHY reset: SRE_FAST, DSE_X1 */ > + MX7D_PAD_ENET1_COL__GPIO7_IO15 0x00 /* X1-96 */ > + /* Clock from PHY to MAC: 100kPU */ > + MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1 0x70 /* X3-4 */ > + /* PHY interrupt: 100kPU, HYS */ > + MX7D_PAD_GPIO1_IO09__GPIO1_IO9 0x78 /* X1-80 */ > + >; > + }; > + > + pinctrl_leds: ledsgrp { > + fsl,pins = < > + MX7D_PAD_LCD_DATA01__GPIO3_IO6 0x14 /* X2-82 */ > + MX7D_PAD_EPDC_BDR0__GPIO2_IO28 0x14 /* X1-82 */ > + MX7D_PAD_EPDC_BDR1__GPIO2_IO29 0x14 /* X1-84 */ > + MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30 0x14 /* X1-86 */ > + MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31 0x14 /* X1-88 */ > + MX7D_PAD_UART2_TX_DATA__GPIO4_IO3 0x14 /* X1-90 */ > + >; > + }; > + > + pinctrl_misc: miscgrp { > + fsl,pins = < > + /* Module A detection (low = present) */ > + MX7D_PAD_LCD_DATA22__GPIO3_IO27 0x7c /* X2-105 */ > + /* Module B detection (low = present) */ > + MX7D_PAD_LCD_DATA20__GPIO3_IO25 0x7c /* X2-103 */ > + /* SMPS - AC input monitor (high = failure) */ > + MX7D_PAD_LCD_DATA07__GPIO3_IO12 0x7c /* X2-88 */ > + /* USB - Hub reset */ > + MX7D_PAD_LCD_DATA09__GPIO3_IO14 0x74 /* X2-92 */ > + >; > + }; > + > + pinctrl_restart: restartgrp { > + fsl,pins = < > + MX7D_PAD_ENET1_TX_CLK__GPIO7_IO12 0x74 /* X1-94 */ > + >; > + }; > + > + pinctrl_uart4: uart4grp { > + fsl,pins = < > + MX7D_PAD_SAI2_TX_SYNC__UART4_DCE_RX 0x7e /* X3-14 */ > + MX7D_PAD_SAI2_TX_BCLK__UART4_DCE_TX 0x76 /* X3-16 */ > + >; > + }; > +}; > + > +&iomuxc_lpsr { > + pinctrl_usbotg2: usbotg2grp { > + fsl,pins = < > + MX7D_PAD_LPSR_GPIO1_IO06__USB_OTG2_OC 0x5c /* X3-11 */ > + MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7 0x59 /* X3-9 */ > + >; > + }; > + > +}; > + > +&uart4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart4>; > + assigned-clocks = <&clks IMX7D_UART4_ROOT_SRC>; > + assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>; > +}; > + > +&usbotg2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbotg2>; > + vbus-supply = <®_usb_otg2_vbus>; > + srp-disable; > + hnp-disable; > + adp-disable; > + dr_mode = "host"; > + status = "okay"; > +}; > + > +/* > + * External watchdog feature provided by pcf2127. > + */ > +&wdog1 { > + status = "disabled"; > +}; > -- > 2.26.2 > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2020-10-28 12:41 UTC | newest] Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2020-09-23 15:40 [PATCH v3 1/2] dt-bindings: fsl: add kamstrup flex concentrator to schema Bruno Thomsen 2020-09-23 15:40 ` [PATCH v3 2/2] ARM: dts: imx7: add support for kamstrup flex concentrator Bruno Thomsen 2020-10-28 12:40 ` Shawn Guo
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).