[PATCH AUTOSEL 4.9 03/22] net: stmmac: Set FIFO sizes for ipq806x

[PATCH AUTOSEL 4.9 03/22] net: stmmac: Set FIFO sizes for ipq806x

[Sasha Levin]

From: Jonathan McDowell <noodles@earth.li>

[ Upstream commit e127906b68b49ddb3ecba39ffa36a329c48197d3 ]

Commit eaf4fac47807 ("net: stmmac: Do not accept invalid MTU values")
started using the TX FIFO size to verify what counts as a valid MTU
request for the stmmac driver.  This is unset for the ipq806x variant.
Looking at older patches for this it seems the RX + TXs buffers can be
up to 8k, so set appropriately.

(I sent this as an RFC patch in June last year, but received no replies.
I've been running with this on my hardware (a MikroTik RB3011) since
then with larger MTUs to support both the internal qca8k switch and
VLANs with no problems. Without the patch it's impossible to set the
larger MTU required to support this.)

Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c
index 1924788d28da..f4ff43a1b5ba 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c
@@ -363,6 +363,8 @@ static int ipq806x_gmac_probe(struct platform_device *pdev)
 	plat_dat->bsp_priv = gmac;
 	plat_dat->fix_mac_speed = ipq806x_gmac_fix_mac_speed;
 	plat_dat->multicast_filter_bins = 0;
+	plat_dat->tx_fifo_size = 8192;
+	plat_dat->rx_fifo_size = 8192;
 
 	err = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
 	if (err)
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 4.9 22/22] net: ethernet: mtk_eth_soc: fix RX VLAN offload

[Sasha Levin]

From: Felix Fietkau <nbd@nbd.name>

[ Upstream commit 3f57d8c40fea9b20543cab4da12f4680d2ef182c ]

The VLAN ID in the rx descriptor is only valid if the RX_DMA_VTAG bit is
set. Fixes frames wrongly marked with VLAN tags.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
[Ilya: fix commit message]
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 2 +-
 drivers/net/ethernet/mediatek/mtk_eth_soc.h | 1 +
 2 files changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index d10c8a8156bc..5b072bf80783 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -964,7 +964,7 @@ static int mtk_poll_rx(struct napi_struct *napi, int budget,
 		skb->protocol = eth_type_trans(skb, netdev);
 
 		if (netdev->features & NETIF_F_HW_VLAN_CTAG_RX &&
-		    RX_DMA_VID(trxd.rxd3))
+		    (trxd.rxd2 & RX_DMA_VTAG))
 			__vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q),
 					       RX_DMA_VID(trxd.rxd3));
 		napi_gro_receive(napi, skb);
diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.h b/drivers/net/ethernet/mediatek/mtk_eth_soc.h
index 99b1c8e9f16f..2e7ccd8261c3 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.h
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.h
@@ -272,6 +272,7 @@
 #define RX_DMA_DONE		BIT(31)
 #define RX_DMA_PLEN0(_x)	(((_x) & 0x3fff) << 16)
 #define RX_DMA_GET_PLEN0(_x)	(((_x) >> 16) & 0x3fff)
+#define RX_DMA_VTAG		BIT(15)
 
 /* QDMA descriptor rxd3 */
 #define RX_DMA_VID(_x)		((_x) & 0xfff)
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel