* [PATCH v1 1/9] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
2021-05-18 8:28 [PATCH v1 0/9] ARM: dts: fixes for Protonic boards Oleksij Rempel
@ 2021-05-18 8:28 ` Oleksij Rempel
2021-05-18 8:28 ` [PATCH v1 2/9] ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio Oleksij Rempel
` (8 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Oleksij Rempel @ 2021-05-18 8:28 UTC (permalink / raw)
To: Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, Robin van der Gracht, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, David Jander
Add touchscreen support to the Protonic VT7 board.
Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index ae6da241f13e..428ed9f6bc17 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -223,6 +223,21 @@ &ecspi2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi2>;
status = "okay";
+
+ touchscreen@0 {
+ compatible = "ti,tsc2046";
+ reg = <0>;
+ pinctrl-0 = <&pinctrl_tsc>;
+ pinctrl-names ="default";
+ spi-max-frequency = <100000>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+ pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+ touchscreen-max-pressure = <4095>;
+ ti,vref-delay-usecs = /bits/ 16 <100>;
+ ti,x-plate-ohms = /bits/ 16 <800>;
+ ti,y-plate-ohms = /bits/ 16 <300>;
+ wakeup-source;
+ };
};
&i2c1 {
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH v1 2/9] ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
2021-05-18 8:28 [PATCH v1 0/9] ARM: dts: fixes for Protonic boards Oleksij Rempel
2021-05-18 8:28 ` [PATCH v1 1/9] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node Oleksij Rempel
@ 2021-05-18 8:28 ` Oleksij Rempel
2021-05-18 8:28 ` [PATCH v1 3/9] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node Oleksij Rempel
` (7 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Oleksij Rempel @ 2021-05-18 8:28 UTC (permalink / raw)
To: Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, Robin van der Gracht, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, David Jander
The backlight power is controlled through the reg_bl_12v0 regulator.
Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 9 ---------
1 file changed, 9 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 428ed9f6bc17..a8e72c7699cd 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,14 +21,11 @@ memory@10000000 {
backlight_lcd: backlight-lcd {
compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_backlight>;
pwms = <&pwm1 0 500000>;
brightness-levels = <0 20 81 248 1000>;
default-brightness-level = <20>;
num-interpolated-steps = <21>;
power-supply = <®_bl_12v0>;
- enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
};
keys {
@@ -315,12 +312,6 @@ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
>;
};
- pinctrl_backlight: backlightgrp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
- >;
- };
-
pinctrl_can1phy: can1phy {
fsl,pins = <
/* CAN1_SR */
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH v1 3/9] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
2021-05-18 8:28 [PATCH v1 0/9] ARM: dts: fixes for Protonic boards Oleksij Rempel
2021-05-18 8:28 ` [PATCH v1 1/9] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node Oleksij Rempel
2021-05-18 8:28 ` [PATCH v1 2/9] ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio Oleksij Rempel
@ 2021-05-18 8:28 ` Oleksij Rempel
2021-05-18 8:28 ` [PATCH v1 4/9] ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties Oleksij Rempel
` (6 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Oleksij Rempel @ 2021-05-18 8:28 UTC (permalink / raw)
To: Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander
At some point PWM cell count was changed, but it didn't triggered any
error, since this DT was overwriting "#pwm-cells".
To make sure, we are in sync with the kernel driver, remove this
property and fix the pwm consumer.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index a8e72c7699cd..d22ded6fc48b 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,7 +21,7 @@ memory@10000000 {
backlight_lcd: backlight-lcd {
compatible = "pwm-backlight";
- pwms = <&pwm1 0 500000>;
+ pwms = <&pwm1 0 500000 0>;
brightness-levels = <0 20 81 248 1000>;
default-brightness-level = <20>;
num-interpolated-steps = <21>;
@@ -273,7 +273,6 @@ &ipu1 {
};
&pwm1 {
- #pwm-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
status = "okay";
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH v1 4/9] ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties
2021-05-18 8:28 [PATCH v1 0/9] ARM: dts: fixes for Protonic boards Oleksij Rempel
` (2 preceding siblings ...)
2021-05-18 8:28 ` [PATCH v1 3/9] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node Oleksij Rempel
@ 2021-05-18 8:28 ` Oleksij Rempel
2021-05-18 8:28 ` [PATCH v1 5/9] ARM: dts: imx6dl: enable touchscreen debounce filter on PLYM2M and PRTVT7 boards Oleksij Rempel
` (5 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Oleksij Rempel @ 2021-05-18 8:28 UTC (permalink / raw)
To: Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander
Remove touchscreen-size-* properties. This values are not correct, event if it
works with ts_test tool, it fails to work properly with weston.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-plym2m.dts | 2 --
1 file changed, 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index 4d0d3d3386af..c97274f0df07 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -138,8 +138,6 @@ touchscreen@0 {
interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
- touchscreen-size-x = <800>;
- touchscreen-size-y = <480>;
touchscreen-inverted-x;
touchscreen-inverted-y;
touchscreen-max-pressure = <4095>;
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH v1 5/9] ARM: dts: imx6dl: enable touchscreen debounce filter on PLYM2M and PRTVT7 boards
2021-05-18 8:28 [PATCH v1 0/9] ARM: dts: fixes for Protonic boards Oleksij Rempel
` (3 preceding siblings ...)
2021-05-18 8:28 ` [PATCH v1 4/9] ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties Oleksij Rempel
@ 2021-05-18 8:28 ` Oleksij Rempel
2021-05-18 8:28 ` [PATCH v1 6/9] ARM: dts: imx6dl-prtvt7: Enable the VPU Oleksij Rempel
` (4 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Oleksij Rempel @ 2021-05-18 8:28 UTC (permalink / raw)
To: Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander
Activate low-pass/debounce filter on the touchscreen.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-plym2m.dts | 4 +++-
arch/arm/boot/dts/imx6dl-prtvt7.dts | 3 +++
2 files changed, 6 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index c97274f0df07..60fe5f14666e 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -145,7 +145,9 @@ touchscreen@0 {
ti,vref-delay-usecs = /bits/ 16 <100>;
ti,x-plate-ohms = /bits/ 16 <800>;
ti,y-plate-ohms = /bits/ 16 <300>;
-
+ ti,debounce-max = /bits/ 16 <3>;
+ ti,debounce-tol = /bits/ 16 <70>;
+ ti,debounce-rep = /bits/ 16 <3>;
wakeup-source;
};
};
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index d22ded6fc48b..1626f3704f1b 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -233,6 +233,9 @@ touchscreen@0 {
ti,vref-delay-usecs = /bits/ 16 <100>;
ti,x-plate-ohms = /bits/ 16 <800>;
ti,y-plate-ohms = /bits/ 16 <300>;
+ ti,debounce-max = /bits/ 16 <3>;
+ ti,debounce-tol = /bits/ 16 <70>;
+ ti,debounce-rep = /bits/ 16 <3>;
wakeup-source;
};
};
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH v1 6/9] ARM: dts: imx6dl-prtvt7: Enable the VPU
2021-05-18 8:28 [PATCH v1 0/9] ARM: dts: fixes for Protonic boards Oleksij Rempel
` (4 preceding siblings ...)
2021-05-18 8:28 ` [PATCH v1 5/9] ARM: dts: imx6dl: enable touchscreen debounce filter on PLYM2M and PRTVT7 boards Oleksij Rempel
@ 2021-05-18 8:28 ` Oleksij Rempel
2021-05-18 8:28 ` [PATCH v1 7/9] ARM: dts: imx6qdl-vicut1: add interrupt-counter nodes Oleksij Rempel
` (3 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Oleksij Rempel @ 2021-05-18 8:28 UTC (permalink / raw)
To: Rob Herring, Sascha Hauer, Shawn Guo
Cc: Robin van der Gracht, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, David Jander
From: Robin van der Gracht <robin@protonic.nl>
Enable Video Processing Unit to make accelerated video decoding work.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 4 ----
1 file changed, 4 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 1626f3704f1b..9b05abe3198f 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -299,10 +299,6 @@ &usbh1 {
status = "disabled";
};
-&vpu {
- status = "disabled";
-};
-
&iomuxc {
pinctrl_audmux: audmuxgrp {
fsl,pins = <
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH v1 7/9] ARM: dts: imx6qdl-vicut1: add interrupt-counter nodes
2021-05-18 8:28 [PATCH v1 0/9] ARM: dts: fixes for Protonic boards Oleksij Rempel
` (5 preceding siblings ...)
2021-05-18 8:28 ` [PATCH v1 6/9] ARM: dts: imx6dl-prtvt7: Enable the VPU Oleksij Rempel
@ 2021-05-18 8:28 ` Oleksij Rempel
2021-05-18 8:28 ` [PATCH v1 8/9] ARM: dts: imx6dl-prtvt7: The sgtl5000 uses i2s not ac97 Oleksij Rempel
` (2 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Oleksij Rempel @ 2021-05-18 8:28 UTC (permalink / raw)
To: Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander
interrupt-counter is mainline now, so we can add missing counter nodes.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 41 ++++++++++++++++++++++++++-
1 file changed, 40 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index eb25d21a2ace..b9e305774fed 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -40,6 +40,27 @@ comp0_out: endpoint {
};
};
+ counter-0 {
+ compatible = "interrupt-counter";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_counter0>;
+ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+ };
+
+ counter-1 {
+ compatible = "interrupt-counter";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_counter1>;
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+ };
+
+ counter-2 {
+ compatible = "interrupt-counter";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_counter2>;
+ gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+ };
+
gpio-keys {
compatible = "gpio-keys";
autorepeat;
@@ -254,7 +275,7 @@ &gpio1 {
&gpio2 {
gpio-line-names =
- "", "", "", "", "", "", "", "",
+ "count0", "count1", "count2", "", "", "", "", "",
"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
"", "", "", "", "", "", "", "ON_SWITCH",
@@ -572,6 +593,24 @@ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
>;
};
+ pinctrl_counter0: counter0grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b000
+ >;
+ };
+
+ pinctrl_counter1: counter1grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b000
+ >;
+ };
+
+ pinctrl_counter2: counter2grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b000
+ >;
+ };
+
pinctrl_ecspi1: ecspi1grp {
fsl,pins = <
MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH v1 8/9] ARM: dts: imx6dl-prtvt7: The sgtl5000 uses i2s not ac97
2021-05-18 8:28 [PATCH v1 0/9] ARM: dts: fixes for Protonic boards Oleksij Rempel
` (6 preceding siblings ...)
2021-05-18 8:28 ` [PATCH v1 7/9] ARM: dts: imx6qdl-vicut1: add interrupt-counter nodes Oleksij Rempel
@ 2021-05-18 8:28 ` Oleksij Rempel
2021-05-18 8:28 ` [PATCH v1 9/9] ARM: dts: imx6dl-prtvt7: Remove unused 'sound-dai-cells' from ssi1 node Oleksij Rempel
2021-06-08 11:49 ` [PATCH v1 0/9] ARM: dts: fixes for Protonic boards Shawn Guo
9 siblings, 0 replies; 11+ messages in thread
From: Oleksij Rempel @ 2021-05-18 8:28 UTC (permalink / raw)
To: Rob Herring, Sascha Hauer, Shawn Guo
Cc: Robin van der Gracht, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, David Jander
From: Robin van der Gracht <robin@protonic.nl>
According to Documentation/devicetree/bindings/sound/fsl,ssi.txt
'fsl,mode' should be specified for AC97 mode only.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 9b05abe3198f..ea6719e2dff9 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -291,7 +291,6 @@ &snvs_pwrkey {
&ssi1 {
#sound-dai-cells = <0>;
- fsl,mode = "ac97-slave";
status = "okay";
};
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH v1 9/9] ARM: dts: imx6dl-prtvt7: Remove unused 'sound-dai-cells' from ssi1 node
2021-05-18 8:28 [PATCH v1 0/9] ARM: dts: fixes for Protonic boards Oleksij Rempel
` (7 preceding siblings ...)
2021-05-18 8:28 ` [PATCH v1 8/9] ARM: dts: imx6dl-prtvt7: The sgtl5000 uses i2s not ac97 Oleksij Rempel
@ 2021-05-18 8:28 ` Oleksij Rempel
2021-06-08 11:49 ` [PATCH v1 0/9] ARM: dts: fixes for Protonic boards Shawn Guo
9 siblings, 0 replies; 11+ messages in thread
From: Oleksij Rempel @ 2021-05-18 8:28 UTC (permalink / raw)
To: Rob Herring, Sascha Hauer, Shawn Guo
Cc: Robin van der Gracht, Oleksij Rempel, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, David Jander
From: Robin van der Gracht <robin@protonic.nl>
The 'fsl,ssi' documentation doesn't say anything about specifying this.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index ea6719e2dff9..190d26642bc8 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -290,7 +290,6 @@ &snvs_pwrkey {
};
&ssi1 {
- #sound-dai-cells = <0>;
status = "okay";
};
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* Re: [PATCH v1 0/9] ARM: dts: fixes for Protonic boards
2021-05-18 8:28 [PATCH v1 0/9] ARM: dts: fixes for Protonic boards Oleksij Rempel
` (8 preceding siblings ...)
2021-05-18 8:28 ` [PATCH v1 9/9] ARM: dts: imx6dl-prtvt7: Remove unused 'sound-dai-cells' from ssi1 node Oleksij Rempel
@ 2021-06-08 11:49 ` Shawn Guo
9 siblings, 0 replies; 11+ messages in thread
From: Shawn Guo @ 2021-06-08 11:49 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Rob Herring, Sascha Hauer, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, David Jander
On Tue, May 18, 2021 at 10:28:41AM +0200, Oleksij Rempel wrote:
> This patch series provide different fixes for Protonic boards.
>
> Oleksij Rempel (6):
> ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
> ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
> ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
> ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties
> ARM: dts: imx6dl: enable touchscreen debounce filter on PLYM2M and
> PRTVT7 boards
> ARM: dts: imx6qdl-vicut1: add interrupt-counter nodes
>
> Robin van der Gracht (3):
> ARM: dts: imx6dl-prtvt7: Enable the VPU
> ARM: dts: imx6dl-prtvt7: The sgtl5000 uses i2s not ac97
> ARM: dts: imx6dl-prtvt7: Remove unused 'sound-dai-cells' from ssi1
> node
Applied all, thanks.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 11+ messages in thread