[PATCH AUTOSEL 4.9 01/11] net: stmmac: allow CSR clock of 300MHz

[PATCH AUTOSEL 4.9 01/11] net: stmmac: allow CSR clock of 300MHz

[Sasha Levin]

From: Jesper Nilsson <jesper.nilsson@axis.com>

[ Upstream commit 08dad2f4d541fcfe5e7bfda72cc6314bbfd2802f ]

The Synopsys Ethernet IP uses the CSR clock as a base clock for MDC.
The divisor used is set in the MAC_MDIO_Address register field CR
(Clock Rate)

The divisor is there to change the CSR clock into a clock that falls
below the IEEE 802.3 specified max frequency of 2.5MHz.

If the CSR clock is 300MHz, the code falls back to using the reset
value in the MAC_MDIO_Address register, as described in the comment
above this code.

However, 300MHz is actually an allowed value and the proper divider
can be estimated quite easily (it's just 1Hz difference!)

A CSR frequency of 300MHz with the maximum clock rate value of 0x5
(STMMAC_CSR_250_300M, a divisor of 124) gives somewhere around
~2.42MHz which is below the IEEE 802.3 specified maximum.

For the ARTPEC-8 SoC, the CSR clock is this problematic 300MHz,
and unfortunately, the reset-value of the MAC_MDIO_Address CR field
is 0x0.

This leads to a clock rate of zero and a divisor of 42, and gives an
MDC frequency of ~7.14MHz.

Allow CSR clock of 300MHz by making the comparison inclusive.

Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index dbd56fefa2f3..0a7ff854d1c3 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -178,7 +178,7 @@ static void stmmac_clk_csr_set(struct stmmac_priv *priv)
 			priv->clk_csr = STMMAC_CSR_100_150M;
 		else if ((clk_rate >= CSR_F_150M) && (clk_rate < CSR_F_250M))
 			priv->clk_csr = STMMAC_CSR_150_250M;
-		else if ((clk_rate >= CSR_F_250M) && (clk_rate < CSR_F_300M))
+		else if ((clk_rate >= CSR_F_250M) && (clk_rate <= CSR_F_300M))
 			priv->clk_csr = STMMAC_CSR_250_300M;
 	}
 }
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 4.9 08/11] arm64: Mark __stack_chk_guard as __ro_after_init

[Sasha Levin]

From: Dan Li <ashimida@linux.alibaba.com>

[ Upstream commit 9fcb2e93f41c07a400885325e7dbdfceba6efaec ]

__stack_chk_guard is setup once while init stage and never changed
after that.

Although the modification of this variable at runtime will usually
cause the kernel to crash (so does the attacker), it should be marked
as __ro_after_init, and it should not affect performance if it is
placed in the ro_after_init section.

Signed-off-by: Dan Li <ashimida@linux.alibaba.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/1631612642-102881-1-git-send-email-ashimida@linux.alibaba.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/kernel/process.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/kernel/process.c b/arch/arm64/kernel/process.c
index e917d119490c..9c62365f8267 100644
--- a/arch/arm64/kernel/process.c
+++ b/arch/arm64/kernel/process.c
@@ -57,7 +57,7 @@
 
 #ifdef CONFIG_CC_STACKPROTECTOR
 #include <linux/stackprotector.h>
-unsigned long __stack_chk_guard __read_mostly;
+unsigned long __stack_chk_guard __ro_after_init;
 EXPORT_SYMBOL(__stack_chk_guard);
 #endif
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel