[PATCH v1 1/4] ARM: dts: imx6dl-prtvt7: Add display and panel nodes

[PATCH v1 1/4] ARM: dts: imx6dl-prtvt7: Add display and panel nodes

[Oleksij Rempel]

Add Innolux G070Y2-T02 panel to the Protonic VT7 board.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 47 +++++++++++++++++++++++++++++
 1 file changed, 47 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 190d26642bc8..be7c4cb339e7 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -28,6 +28,30 @@ backlight_lcd: backlight-lcd {
 		power-supply = <&reg_bl_12v0>;
 	};
 
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-0 = <&pinctrl_ipu1_disp>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
 	keys {
 		compatible = "gpio-keys";
 		autorepeat;
@@ -135,6 +159,18 @@ led-debug0 {
 		};
 	};
 
+	panel {
+		compatible = "innolux,g070y2-t02";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
 	reg_bl_12v0: regulator-bl-12v0 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -146,6 +182,13 @@ reg_bl_12v0: regulator-bl-12v0 {
 		enable-active-high;
 	};
 
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_1v8: regulator-1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "1v8";
@@ -275,6 +318,10 @@ &ipu1 {
 	status = "okay";
 };
 
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display_in>;
+};
+
 &pwm1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 2/4] ARM: dts: imx6dl-prtvt7: Add missing tvp5150 video decoder node

[Oleksij Rempel]

From: Robin van der Gracht <robin@protonic.nl>

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 40 +++++++++++++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index be7c4cb339e7..02b53df03e6f 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -6,6 +6,7 @@
 /dts-v1/;
 #include "imx6dl.dtsi"
 #include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/display/sdtv-standards.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/sound/fsl-imx-audmux.h>
@@ -171,6 +172,18 @@ panel_in: endpoint {
 		};
 	};
 
+	connector {
+		compatible = "composite-video-connector";
+		label = "Composite0";
+		sdtv-standards = <SDTV_STD_PAL_B>;
+
+		port {
+			comp0_out: endpoint {
+				remote-endpoint = <&tvp5150_comp0_in>;
+			};
+		};
+	};
+
 	reg_bl_12v0: regulator-bl-12v0 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -295,6 +308,29 @@ sgtl5000: audio-codec@a {
 		VDDIO-supply = <&reg_3v3>;
 		VDDD-supply = <&reg_1v8>;
 	};
+
+	video@5c {
+		compatible = "ti,tvp5150";
+		reg = <0x5c>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			tvp5150_comp0_in: endpoint {
+				remote-endpoint = <&comp0_out>;
+			};
+		};
+
+		/* Output port 2 is video output pad */
+		port@2 {
+			reg = <2>;
+			tvp5151_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+			};
+		};
+	};
 };
 
 &i2c3 {
@@ -322,6 +358,10 @@ &ipu1_di0_disp0 {
 	remote-endpoint = <&display_in>;
 };
 
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
+};
+
 &pwm1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 3/4] ARM: dts: imx6qdl-vicut1: add CAN termination support

[Oleksij Rempel]

The gpio1 0 pin is controlling CAN termination, not USB H1 VBUS. So,
remove wrong regulator and assign this GPIO to the new DT CAN termination
property.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 12 ++----------
 1 file changed, 2 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index b9e305774fed..1ac7e13249d2 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -126,15 +126,6 @@ reg_3v3: regulator-3v3 {
 		regulator-max-microvolt = <3300000>;
 	};
 
-	reg_h1_vbus: regulator-h1-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "h1-vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
 	reg_otg_vbus: regulator-otg-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "otg-vbus";
@@ -212,6 +203,8 @@ IMX_AUDMUX_V2_PTCR_SYN		IMX_AUDMUX_V2_PDCR_RXDSEL(0)
 &can1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_can1>;
+	termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	termination-ohms = <150>;
 	status = "okay";
 };
 
@@ -492,7 +485,6 @@ &uart5 {
 };
 
 &usbh1 {
-	vbus-supply = <&reg_h1_vbus>;
 	pinctrl-names = "default";
 	phy_type = "utmi";
 	dr_mode = "host";
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 4/4] ARM: dts: imx6dl: plym2m, prtvt7, victgo: make use of new resistive-adc-touch driver

[Oleksij Rempel]

The tsc2046 is an ADC used as touchscreen controller. To share as mach
code as possible, we should use it as actual ADC + virtual tochscreen
controller.
With this patch we make use of the new kernel IIO and HID infrastructure.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-plym2m.dts | 55 ++++++++++++++++++++---------
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 53 ++++++++++++++++++++-------
 arch/arm/boot/dts/imx6dl-victgo.dts | 55 +++++++++++++++++++++--------
 3 files changed, 120 insertions(+), 43 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index 60fe5f14666e..e2afedae85cb 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -101,6 +101,17 @@ reg_12v0: regulator-12v0 {
 		regulator-min-microvolt = <12000000>;
 		regulator-max-microvolt = <12000000>;
 	};
+
+	touchscreen {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc 1>, <&adc 3>, <&adc 4>, <&adc 5>;
+		io-channel-names = "y", "z1", "z2", "x";
+		touchscreen-min-pressure = <64687>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		touchscreen-x-plate-ohms = <300>;
+		touchscreen-y-plate-ohms = <800>;
+	};
 };
 
 &can1 {
@@ -129,26 +140,38 @@ &ecspi2 {
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
 
-	touchscreen@0 {
-		compatible = "ti,tsc2046";
+	adc: adc@0 {
+		compatible = "ti,tsc2046e-adc";
 		reg = <0>;
 		pinctrl-0 = <&pinctrl_tsc2046>;
 		pinctrl-names ="default";
-		spi-max-frequency = <100000>;
-		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
-		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+		spi-max-frequency = <1000000>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
+		#io-channel-cells = <1>;
 
-		touchscreen-inverted-x;
-		touchscreen-inverted-y;
-		touchscreen-max-pressure = <4095>;
-
-		ti,vref-delay-usecs = /bits/ 16 <100>;
-		ti,x-plate-ohms = /bits/ 16 <800>;
-		ti,y-plate-ohms = /bits/ 16 <300>;
-		ti,debounce-max = /bits/ 16 <3>;
-		ti,debounce-tol = /bits/ 16 <70>;
-		ti,debounce-rep = /bits/ 16 <3>;
-		wakeup-source;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@1 {
+			reg = <1>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+		channel@3 {
+			reg = <3>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+		channel@4 {
+			reg = <4>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+		channel@5 {
+			reg = <5>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 02b53df03e6f..c361e0683973 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -235,6 +235,17 @@ simple-audio-card,codec {
 			frame-master;
 		};
 	};
+
+	touchscreen {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc 1>, <&adc 3>, <&adc 4>, <&adc 5>;
+		io-channel-names = "y", "z1", "z2", "x";
+		touchscreen-min-pressure = <64687>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		touchscreen-x-plate-ohms = <300>;
+		touchscreen-y-plate-ohms = <800>;
+	};
 };
 
 &audmux {
@@ -277,22 +288,38 @@ &ecspi2 {
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
 
-	touchscreen@0 {
-		compatible = "ti,tsc2046";
+	adc: adc@0 {
+		compatible = "ti,tsc2046e-adc";
 		reg = <0>;
 		pinctrl-0 = <&pinctrl_tsc>;
 		pinctrl-names ="default";
-		spi-max-frequency = <100000>;
-		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
-		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
-		touchscreen-max-pressure = <4095>;
-		ti,vref-delay-usecs = /bits/ 16 <100>;
-		ti,x-plate-ohms = /bits/ 16 <800>;
-		ti,y-plate-ohms = /bits/ 16 <300>;
-		ti,debounce-max = /bits/ 16 <3>;
-		ti,debounce-tol = /bits/ 16 <70>;
-		ti,debounce-rep = /bits/ 16 <3>;
-		wakeup-source;
+		spi-max-frequency = <1000000>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
+		#io-channel-cells = <1>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@1 {
+			reg = <1>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+		channel@3 {
+			reg = <3>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+		channel@4 {
+			reg = <4>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+		channel@5 {
+			reg = <5>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index d37ba4ed847d..b5004b322d44 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -181,6 +181,17 @@ simple-audio-card,codec {
 			frame-master;
 		};
 	};
+
+	touchscreen {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc 1>, <&adc 3>, <&adc 4>, <&adc 5>;
+		io-channel-names = "y", "z1", "z2", "x";
+		touchscreen-min-pressure = <64687>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		touchscreen-x-plate-ohms = <300>;
+		touchscreen-y-plate-ohms = <800>;
+	};
 };
 
 &audmux {
@@ -244,22 +255,38 @@ &ecspi2 {
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
 
-	touchscreen@0 {
-		compatible = "ti,tsc2046";
+	adc: adc@0 {
+		compatible = "ti,tsc2046e-adc";
 		reg = <0>;
-		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_touchscreen>;
-		spi-max-frequency = <200000>;
-		interrupts-extended = <&gpio5 8 IRQ_TYPE_EDGE_FALLING>;
-		pendown-gpio = <&gpio5 8 GPIO_ACTIVE_LOW>;
-		touchscreen-size-x = <800>;
-		touchscreen-size-y = <480>;
-		touchscreen-inverted-y;
-		touchscreen-max-pressure = <4095>;
-		ti,vref-delay-usecs = /bits/ 16 <100>;
-		ti,x-plate-ohms = /bits/ 16 <800>;
-		ti,y-plate-ohms = /bits/ 16 <300>;
-		wakeup-source;
+		pinctrl-names ="default";
+		spi-max-frequency = <1000000>;
+		interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
+		#io-channel-cells = <1>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@1 {
+			reg = <1>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+		channel@3 {
+			reg = <3>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+		channel@4 {
+			reg = <4>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+		channel@5 {
+			reg = <5>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
 	};
 };
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 2/4] ARM: dts: imx6dl-prtvt7: Add missing tvp5150 video decoder node

[Shawn Guo]

On Mon, Nov 22, 2021 at 01:43:08PM +0100, Oleksij Rempel wrote:
> From: Robin van der Gracht <robin@protonic.nl>
> 
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> ---
>  arch/arm/boot/dts/imx6dl-prtvt7.dts | 40 +++++++++++++++++++++++++++++
>  1 file changed, 40 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> index be7c4cb339e7..02b53df03e6f 100644
> --- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
> +++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> @@ -6,6 +6,7 @@
>  /dts-v1/;
>  #include "imx6dl.dtsi"
>  #include "imx6qdl-prti6q.dtsi"
> +#include <dt-bindings/display/sdtv-standards.h>
>  #include <dt-bindings/input/input.h>
>  #include <dt-bindings/leds/common.h>
>  #include <dt-bindings/sound/fsl-imx-audmux.h>
> @@ -171,6 +172,18 @@ panel_in: endpoint {
>  		};
>  	};
>  
> +	connector {
> +		compatible = "composite-video-connector";
> +		label = "Composite0";
> +		sdtv-standards = <SDTV_STD_PAL_B>;
> +
> +		port {
> +			comp0_out: endpoint {
> +				remote-endpoint = <&tvp5150_comp0_in>;
> +			};
> +		};
> +	};
> +
>  	reg_bl_12v0: regulator-bl-12v0 {
>  		compatible = "regulator-fixed";
>  		pinctrl-names = "default";
> @@ -295,6 +308,29 @@ sgtl5000: audio-codec@a {
>  		VDDIO-supply = <&reg_3v3>;
>  		VDDD-supply = <&reg_1v8>;
>  	};
> +
> +	video@5c {
> +		compatible = "ti,tvp5150";
> +		reg = <0x5c>;
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		port@0 {
> +			reg = <0>;

Have a newline between property and child node.

Shawn

> +			tvp5150_comp0_in: endpoint {
> +				remote-endpoint = <&comp0_out>;
> +			};
> +		};
> +
> +		/* Output port 2 is video output pad */
> +		port@2 {
> +			reg = <2>;
> +			tvp5151_to_ipu1_csi0_mux: endpoint {
> +				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
> +			};
> +		};
> +	};
>  };
>  
>  &i2c3 {
> @@ -322,6 +358,10 @@ &ipu1_di0_disp0 {
>  	remote-endpoint = <&display_in>;
>  };
>  
> +&ipu1_csi0_mux_from_parallel_sensor {
> +	remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
> +};
> +
>  &pwm1 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_pwm1>;
> -- 
> 2.30.2
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 4/4] ARM: dts: imx6dl: plym2m, prtvt7, victgo: make use of new resistive-adc-touch driver

[Shawn Guo]

On Mon, Nov 22, 2021 at 01:43:10PM +0100, Oleksij Rempel wrote:
> The tsc2046 is an ADC used as touchscreen controller. To share as mach
> code as possible, we should use it as actual ADC + virtual tochscreen
> controller.
> With this patch we make use of the new kernel IIO and HID infrastructure.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>

One space is enough in subject "victgo:  make".

> ---
>  arch/arm/boot/dts/imx6dl-plym2m.dts | 55 ++++++++++++++++++++---------
>  arch/arm/boot/dts/imx6dl-prtvt7.dts | 53 ++++++++++++++++++++-------
>  arch/arm/boot/dts/imx6dl-victgo.dts | 55 +++++++++++++++++++++--------
>  3 files changed, 120 insertions(+), 43 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
> index 60fe5f14666e..e2afedae85cb 100644
> --- a/arch/arm/boot/dts/imx6dl-plym2m.dts
> +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
> @@ -101,6 +101,17 @@ reg_12v0: regulator-12v0 {
>  		regulator-min-microvolt = <12000000>;
>  		regulator-max-microvolt = <12000000>;
>  	};
> +
> +	touchscreen {
> +		compatible = "resistive-adc-touch";
> +		io-channels = <&adc 1>, <&adc 3>, <&adc 4>, <&adc 5>;
> +		io-channel-names = "y", "z1", "z2", "x";
> +		touchscreen-min-pressure = <64687>;
> +		touchscreen-inverted-x;
> +		touchscreen-inverted-y;
> +		touchscreen-x-plate-ohms = <300>;
> +		touchscreen-y-plate-ohms = <800>;
> +	};
>  };
>  
>  &can1 {
> @@ -129,26 +140,38 @@ &ecspi2 {
>  	pinctrl-0 = <&pinctrl_ecspi2>;
>  	status = "okay";
>  
> -	touchscreen@0 {
> -		compatible = "ti,tsc2046";
> +	adc: adc@0 {

Isn't label name "adc" too generic?

> +		compatible = "ti,tsc2046e-adc";
>  		reg = <0>;
>  		pinctrl-0 = <&pinctrl_tsc2046>;
>  		pinctrl-names ="default";
> -		spi-max-frequency = <100000>;
> -		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
> -		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
> +		spi-max-frequency = <1000000>;
> +		interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
> +		#io-channel-cells = <1>;
>  
> -		touchscreen-inverted-x;
> -		touchscreen-inverted-y;
> -		touchscreen-max-pressure = <4095>;
> -
> -		ti,vref-delay-usecs = /bits/ 16 <100>;
> -		ti,x-plate-ohms = /bits/ 16 <800>;
> -		ti,y-plate-ohms = /bits/ 16 <300>;
> -		ti,debounce-max = /bits/ 16 <3>;
> -		ti,debounce-tol = /bits/ 16 <70>;
> -		ti,debounce-rep = /bits/ 16 <3>;
> -		wakeup-source;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		channel@1 {
> +			reg = <1>;
> +			settling-time-us = <700>;
> +			oversampling-ratio = <5>;
> +		};

Have a newline between child nodes.

Shawn

> +		channel@3 {
> +			reg = <3>;
> +			settling-time-us = <700>;
> +			oversampling-ratio = <5>;
> +		};
> +		channel@4 {
> +			reg = <4>;
> +			settling-time-us = <700>;
> +			oversampling-ratio = <5>;
> +		};
> +		channel@5 {
> +			reg = <5>;
> +			settling-time-us = <700>;
> +			oversampling-ratio = <5>;
> +		};
>  	};
>  };
>  
> diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> index 02b53df03e6f..c361e0683973 100644
> --- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
> +++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> @@ -235,6 +235,17 @@ simple-audio-card,codec {
>  			frame-master;
>  		};
>  	};
> +
> +	touchscreen {
> +		compatible = "resistive-adc-touch";
> +		io-channels = <&adc 1>, <&adc 3>, <&adc 4>, <&adc 5>;
> +		io-channel-names = "y", "z1", "z2", "x";
> +		touchscreen-min-pressure = <64687>;
> +		touchscreen-inverted-x;
> +		touchscreen-inverted-y;
> +		touchscreen-x-plate-ohms = <300>;
> +		touchscreen-y-plate-ohms = <800>;
> +	};
>  };
>  
>  &audmux {
> @@ -277,22 +288,38 @@ &ecspi2 {
>  	pinctrl-0 = <&pinctrl_ecspi2>;
>  	status = "okay";
>  
> -	touchscreen@0 {
> -		compatible = "ti,tsc2046";
> +	adc: adc@0 {
> +		compatible = "ti,tsc2046e-adc";
>  		reg = <0>;
>  		pinctrl-0 = <&pinctrl_tsc>;
>  		pinctrl-names ="default";
> -		spi-max-frequency = <100000>;
> -		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
> -		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
> -		touchscreen-max-pressure = <4095>;
> -		ti,vref-delay-usecs = /bits/ 16 <100>;
> -		ti,x-plate-ohms = /bits/ 16 <800>;
> -		ti,y-plate-ohms = /bits/ 16 <300>;
> -		ti,debounce-max = /bits/ 16 <3>;
> -		ti,debounce-tol = /bits/ 16 <70>;
> -		ti,debounce-rep = /bits/ 16 <3>;
> -		wakeup-source;
> +		spi-max-frequency = <1000000>;
> +		interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
> +		#io-channel-cells = <1>;
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		channel@1 {
> +			reg = <1>;
> +			settling-time-us = <700>;
> +			oversampling-ratio = <5>;
> +		};
> +		channel@3 {
> +			reg = <3>;
> +			settling-time-us = <700>;
> +			oversampling-ratio = <5>;
> +		};
> +		channel@4 {
> +			reg = <4>;
> +			settling-time-us = <700>;
> +			oversampling-ratio = <5>;
> +		};
> +		channel@5 {
> +			reg = <5>;
> +			settling-time-us = <700>;
> +			oversampling-ratio = <5>;
> +		};
>  	};
>  };
>  
> diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
> index d37ba4ed847d..b5004b322d44 100644
> --- a/arch/arm/boot/dts/imx6dl-victgo.dts
> +++ b/arch/arm/boot/dts/imx6dl-victgo.dts
> @@ -181,6 +181,17 @@ simple-audio-card,codec {
>  			frame-master;
>  		};
>  	};
> +
> +	touchscreen {
> +		compatible = "resistive-adc-touch";
> +		io-channels = <&adc 1>, <&adc 3>, <&adc 4>, <&adc 5>;
> +		io-channel-names = "y", "z1", "z2", "x";
> +		touchscreen-min-pressure = <64687>;
> +		touchscreen-inverted-x;
> +		touchscreen-inverted-y;
> +		touchscreen-x-plate-ohms = <300>;
> +		touchscreen-y-plate-ohms = <800>;
> +	};
>  };
>  
>  &audmux {
> @@ -244,22 +255,38 @@ &ecspi2 {
>  	pinctrl-0 = <&pinctrl_ecspi2>;
>  	status = "okay";
>  
> -	touchscreen@0 {
> -		compatible = "ti,tsc2046";
> +	adc: adc@0 {
> +		compatible = "ti,tsc2046e-adc";
>  		reg = <0>;
> -		pinctrl-names = "default";
>  		pinctrl-0 = <&pinctrl_touchscreen>;
> -		spi-max-frequency = <200000>;
> -		interrupts-extended = <&gpio5 8 IRQ_TYPE_EDGE_FALLING>;
> -		pendown-gpio = <&gpio5 8 GPIO_ACTIVE_LOW>;
> -		touchscreen-size-x = <800>;
> -		touchscreen-size-y = <480>;
> -		touchscreen-inverted-y;
> -		touchscreen-max-pressure = <4095>;
> -		ti,vref-delay-usecs = /bits/ 16 <100>;
> -		ti,x-plate-ohms = /bits/ 16 <800>;
> -		ti,y-plate-ohms = /bits/ 16 <300>;
> -		wakeup-source;
> +		pinctrl-names ="default";
> +		spi-max-frequency = <1000000>;
> +		interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
> +		#io-channel-cells = <1>;
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		channel@1 {
> +			reg = <1>;
> +			settling-time-us = <700>;
> +			oversampling-ratio = <5>;
> +		};
> +		channel@3 {
> +			reg = <3>;
> +			settling-time-us = <700>;
> +			oversampling-ratio = <5>;
> +		};
> +		channel@4 {
> +			reg = <4>;
> +			settling-time-us = <700>;
> +			oversampling-ratio = <5>;
> +		};
> +		channel@5 {
> +			reg = <5>;
> +			settling-time-us = <700>;
> +			oversampling-ratio = <5>;
> +		};
>  	};
>  };
>  
> -- 
> 2.30.2
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 4/4] ARM: dts: imx6dl: plym2m, prtvt7, victgo: make use of new resistive-adc-touch driver

[Oleksij Rempel]

Hi Shawn,

sorry for the delay, I just came back to work.

On Mon, Dec 06, 2021 at 09:06:28AM +0800, Shawn Guo wrote:
> On Mon, Nov 22, 2021 at 01:43:10PM +0100, Oleksij Rempel wrote:
> > The tsc2046 is an ADC used as touchscreen controller. To share as mach
> > code as possible, we should use it as actual ADC + virtual tochscreen
> > controller.
> > With this patch we make use of the new kernel IIO and HID infrastructure.
> > 
> > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> 
> One space is enough in subject "victgo:  make".

done.

> > ---
> >  arch/arm/boot/dts/imx6dl-plym2m.dts | 55 ++++++++++++++++++++---------
> >  arch/arm/boot/dts/imx6dl-prtvt7.dts | 53 ++++++++++++++++++++-------
> >  arch/arm/boot/dts/imx6dl-victgo.dts | 55 +++++++++++++++++++++--------
> >  3 files changed, 120 insertions(+), 43 deletions(-)
> > 
> > diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > index 60fe5f14666e..e2afedae85cb 100644
> > --- a/arch/arm/boot/dts/imx6dl-plym2m.dts
> > +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > @@ -101,6 +101,17 @@ reg_12v0: regulator-12v0 {
> >  		regulator-min-microvolt = <12000000>;
> >  		regulator-max-microvolt = <12000000>;
> >  	};
> > +
> > +	touchscreen {
> > +		compatible = "resistive-adc-touch";
> > +		io-channels = <&adc 1>, <&adc 3>, <&adc 4>, <&adc 5>;
> > +		io-channel-names = "y", "z1", "z2", "x";
> > +		touchscreen-min-pressure = <64687>;
> > +		touchscreen-inverted-x;
> > +		touchscreen-inverted-y;
> > +		touchscreen-x-plate-ohms = <300>;
> > +		touchscreen-y-plate-ohms = <800>;
> > +	};
> >  };
> >  
> >  &can1 {
> > @@ -129,26 +140,38 @@ &ecspi2 {
> >  	pinctrl-0 = <&pinctrl_ecspi2>;
> >  	status = "okay";
> >  
> > -	touchscreen@0 {
> > -		compatible = "ti,tsc2046";
> > +	adc: adc@0 {
> 
> Isn't label name "adc" too generic?

I do not have strong opinion about this. Currently we have no
restrictions for the node names:
Documentation/devicetree/bindings/iio/adc/ti,tsc2046.yaml
Documentation/devicetree/bindings/iio/adc/adc.yaml

I can name it touchscreen-adc@0 or something like this. What are your
preferences?

Regards,
Oleksij
-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 4/4] ARM: dts: imx6dl: plym2m, prtvt7, victgo: make use of new resistive-adc-touch driver

[Shawn Guo]

On Wed, Jan 05, 2022 at 12:04:34PM +0100, Oleksij Rempel wrote:
> Hi Shawn,
> 
> sorry for the delay, I just came back to work.
> 
> On Mon, Dec 06, 2021 at 09:06:28AM +0800, Shawn Guo wrote:
> > On Mon, Nov 22, 2021 at 01:43:10PM +0100, Oleksij Rempel wrote:
> > > The tsc2046 is an ADC used as touchscreen controller. To share as mach
> > > code as possible, we should use it as actual ADC + virtual tochscreen
> > > controller.
> > > With this patch we make use of the new kernel IIO and HID infrastructure.
> > > 
> > > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> > 
> > One space is enough in subject "victgo:  make".
> 
> done.
> 
> > > ---
> > >  arch/arm/boot/dts/imx6dl-plym2m.dts | 55 ++++++++++++++++++++---------
> > >  arch/arm/boot/dts/imx6dl-prtvt7.dts | 53 ++++++++++++++++++++-------
> > >  arch/arm/boot/dts/imx6dl-victgo.dts | 55 +++++++++++++++++++++--------
> > >  3 files changed, 120 insertions(+), 43 deletions(-)
> > > 
> > > diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > > index 60fe5f14666e..e2afedae85cb 100644
> > > --- a/arch/arm/boot/dts/imx6dl-plym2m.dts
> > > +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > > @@ -101,6 +101,17 @@ reg_12v0: regulator-12v0 {
> > >  		regulator-min-microvolt = <12000000>;
> > >  		regulator-max-microvolt = <12000000>;
> > >  	};
> > > +
> > > +	touchscreen {
> > > +		compatible = "resistive-adc-touch";
> > > +		io-channels = <&adc 1>, <&adc 3>, <&adc 4>, <&adc 5>;
> > > +		io-channel-names = "y", "z1", "z2", "x";
> > > +		touchscreen-min-pressure = <64687>;
> > > +		touchscreen-inverted-x;
> > > +		touchscreen-inverted-y;
> > > +		touchscreen-x-plate-ohms = <300>;
> > > +		touchscreen-y-plate-ohms = <800>;
> > > +	};
> > >  };
> > >  
> > >  &can1 {
> > > @@ -129,26 +140,38 @@ &ecspi2 {
> > >  	pinctrl-0 = <&pinctrl_ecspi2>;
> > >  	status = "okay";
> > >  
> > > -	touchscreen@0 {
> > > -		compatible = "ti,tsc2046";
> > > +	adc: adc@0 {
> > 
> > Isn't label name "adc" too generic?
> 
> I do not have strong opinion about this. Currently we have no
> restrictions for the node names:
> Documentation/devicetree/bindings/iio/adc/ti,tsc2046.yaml
> Documentation/devicetree/bindings/iio/adc/adc.yaml
> 
> I can name it touchscreen-adc@0 or something like this. What are your
> preferences?

I wasn't talking about node name but label.

Shawn

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel