From: Li Yang <leoyang.li@nxp.com>
To: Rob Herring <robh+dt@kernel.org>, Shawn Guo <shawnguo@kernel.org>,
Li Yang <leoyang.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>,
Santan Kumar <santan.kumar@nxp.com>,
Tao Yang <b31903@freescale.com>,
Yogesh Gaur <yogeshnarayan.gaur@nxp.com>,
Abhimanyu Saini <abhimanyu.saini@nxp.com>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH 4/6] arm64: dts: ls2081a-rdb: Add DTS support for NXP LS2081ARDB
Date: Thu, 17 Mar 2022 14:01:07 -0500 [thread overview]
Message-ID: <20220317190109.3742-4-leoyang.li@nxp.com> (raw)
In-Reply-To: <20220317190109.3742-1-leoyang.li@nxp.com>
From: Priyanka Jain <priyanka.jain@nxp.com>
This patch add support for NXP LS2081ARDB board which has
LS2081A SoC.
LS2081A SoC is 40-pin derivative of LS2088A SoC So, from functional
perspective both are same. Hence,ls2088a SoC dtsi files are included
from ls2081ARDB dts
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Tao Yang <b31903@freescale.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../boot/dts/freescale/fsl-ls2081a-rdb.dts | 131 ++++++++++++++++++
2 files changed, 132 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls2081a-rdb.dts
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 6d8f0a532587..1b5cb71a6828 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -38,6 +38,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-ten64.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2081a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2081a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2081a-rdb.dts
new file mode 100644
index 000000000000..908b9aff0489
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2081a-rdb.dts
@@ -0,0 +1,131 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for NXP LS2081A RDB Board.
+ *
+ * Copyright 2017 NXP
+ *
+ * Priyanka Jain <priyanka.jain@nxp.com>
+ *
+ */
+
+/dts-v1/;
+
+#include "fsl-ls2088a.dtsi"
+
+/ {
+ model = "NXP Layerscape 2081A RDB Board";
+ compatible = "fsl,ls2081a-rdb", "fsl,ls2081a";
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ };
+
+ chosen {
+ stdout-path = "serial1:115200n8";
+ };
+};
+
+&dspi {
+ status = "okay";
+
+ n25q512a: flash@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <3000000>;
+ reg = <0>;
+ };
+};
+
+&esdhc {
+ status = "okay";
+};
+
+&ifc {
+ status = "disabled";
+};
+
+&i2c0 {
+ status = "okay";
+
+ pca9547: mux@75 {
+ compatible = "nxp,pca9547";
+ reg = <0x75>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x01>;
+ rtc@51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ };
+ };
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x02>;
+
+ ina220@40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <500>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ adt7481@4c {
+ compatible = "adi,adt7461";
+ reg = <0x4c>;
+ };
+ };
+ };
+};
+
+&qspi {
+ status = "okay";
+
+ s25fs512s0: flash@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+
+ s25fs512s1: flash@1 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
+ spi-max-frequency = <20000000>;
+ reg = <1>;
+ };
+};
+
+&sata0 {
+ status = "okay";
+};
+
+&sata1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2022-03-17 19:03 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-03-17 19:01 [PATCH 1/6] arm64: dts: ls2080a-qds: add mdio mux nodes from on-board FPGA Li Yang
2022-03-17 19:01 ` [PATCH 2/6] arm64: dts: ls2088a-qds: " Li Yang
2022-03-17 19:01 ` [PATCH 3/6] arm64: dts: ls2080a-rdb: add phy nodes Li Yang
2022-04-10 1:12 ` Shawn Guo
2022-03-17 19:01 ` Li Yang [this message]
2022-04-10 1:19 ` [PATCH 4/6] arm64: dts: ls2081a-rdb: Add DTS support for NXP LS2081ARDB Shawn Guo
2022-03-17 19:01 ` [PATCH 5/6] arm64: dts: ls208xa-rdb: fix errata E-00013 Li Yang
2022-04-10 1:25 ` Shawn Guo
2022-03-17 19:01 ` [PATCH 6/6] arm64: dts: ls208x: remove NXP Erratum A008585 from LS2088A Li Yang
2022-04-10 1:27 ` Shawn Guo
2022-04-10 1:10 ` [PATCH 1/6] arm64: dts: ls2080a-qds: add mdio mux nodes from on-board FPGA Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220317190109.3742-4-leoyang.li@nxp.com \
--to=leoyang.li@nxp.com \
--cc=abhimanyu.saini@nxp.com \
--cc=b31903@freescale.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=priyanka.jain@nxp.com \
--cc=robh+dt@kernel.org \
--cc=santan.kumar@nxp.com \
--cc=shawnguo@kernel.org \
--cc=yogeshnarayan.gaur@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).