From: Li Yang <leoyang.li@nxp.com>
To: shawnguo@kernel.org, devicetree@vger.kernel.org
Cc: robh+dt@kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, Li Yang <leoyang.li@nxp.com>,
Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Subject: [PATCH v4 1/2] arm64: dts: lx2160a: update PCIe nodes to match rev2 silicon
Date: Wed, 17 Aug 2022 15:25:37 -0500 [thread overview]
Message-ID: <20220817202538.21493-2-leoyang.li@nxp.com> (raw)
In-Reply-To: <20220817202538.21493-1-leoyang.li@nxp.com>
The original dts was created based on the non-production rev1 silicon
which was only used for evaluation. Update the PCIe nodes to align with
the different controller used in production rev2 silicon.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
---
.../arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 96 +++++++++----------
1 file changed, 48 insertions(+), 48 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
index 6680fb2a6dc9..a7c549277dcc 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
@@ -1104,10 +1104,10 @@ sata3: sata@3230000 {
};
pcie1: pcie@3400000 {
- compatible = "fsl,lx2160a-pcie";
- reg = <0x00 0x03400000 0x0 0x00100000>, /* controller registers */
- <0x80 0x00000000 0x0 0x00002000>; /* configuration space */
- reg-names = "csr_axi_slave", "config_axi_slave";
+ compatible = "fsl,lx2160ar2-pcie", "fsl,ls2088a-pcie";
+ reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */
+ 0x80 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
@@ -1116,26 +1116,26 @@ pcie1: pcie@3400000 {
#size-cells = <2>;
device_type = "pci";
dma-coherent;
- apio-wins = <8>;
- ppio-wins = <8>;
+ num-viewport = <8>;
bus-range = <0x0 0xff>;
- ranges = <0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ ranges = <0x81000000 0x0 0x00000000 0x80 0x00010000 0x0 0x00010000
+ 0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
msi-parent = <&its>;
+ iommu-map = <0 &smmu 0 1>; /* This is fixed-up by u-boot */
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 2 &gic 0 0 GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 3 &gic 0 0 GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 4 &gic 0 0 GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
- iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
status = "disabled";
};
pcie2: pcie@3500000 {
- compatible = "fsl,lx2160a-pcie";
- reg = <0x00 0x03500000 0x0 0x00100000>, /* controller registers */
- <0x88 0x00000000 0x0 0x00002000>; /* configuration space */
- reg-names = "csr_axi_slave", "config_axi_slave";
+ compatible = "fsl,lx2160ar2-pcie", "fsl,ls2088a-pcie";
+ reg = <0x00 0x03500000 0x0 0x00100000 /* controller registers */
+ 0x88 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
<GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
<GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
@@ -1144,26 +1144,26 @@ pcie2: pcie@3500000 {
#size-cells = <2>;
device_type = "pci";
dma-coherent;
- apio-wins = <8>;
- ppio-wins = <8>;
+ num-viewport = <8>;
bus-range = <0x0 0xff>;
- ranges = <0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ ranges = <0x81000000 0x0 0x00000000 0x88 0x00010000 0x0 0x00010000
+ 0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
msi-parent = <&its>;
+ iommu-map = <0 &smmu 0 1>; /* This is fixed-up by u-boot */
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 2 &gic 0 0 GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 3 &gic 0 0 GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 4 &gic 0 0 GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
- iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
status = "disabled";
};
pcie3: pcie@3600000 {
- compatible = "fsl,lx2160a-pcie";
- reg = <0x00 0x03600000 0x0 0x00100000>, /* controller registers */
- <0x90 0x00000000 0x0 0x00002000>; /* configuration space */
- reg-names = "csr_axi_slave", "config_axi_slave";
+ compatible = "fsl,lx2160ar2-pcie", "fsl,ls2088a-pcie";
+ reg = <0x00 0x03600000 0x0 0x00100000 /* controller registers */
+ 0x90 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
<GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
<GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
@@ -1172,26 +1172,26 @@ pcie3: pcie@3600000 {
#size-cells = <2>;
device_type = "pci";
dma-coherent;
- apio-wins = <256>;
- ppio-wins = <24>;
+ num-viewport = <256>;
bus-range = <0x0 0xff>;
- ranges = <0x82000000 0x0 0x40000000 0x90 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ ranges = <0x81000000 0x0 0x00000000 0x90 0x00010000 0x0 0x00010000
+ 0x82000000 0x0 0x40000000 0x90 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
msi-parent = <&its>;
+ iommu-map = <0 &smmu 0 1>; /* This is fixed-up by u-boot */
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 2 &gic 0 0 GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 3 &gic 0 0 GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 4 &gic 0 0 GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
- iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
status = "disabled";
};
pcie4: pcie@3700000 {
- compatible = "fsl,lx2160a-pcie";
- reg = <0x00 0x03700000 0x0 0x00100000>, /* controller registers */
- <0x98 0x00000000 0x0 0x00002000>; /* configuration space */
- reg-names = "csr_axi_slave", "config_axi_slave";
+ compatible = "fsl,lx2160ar2-pcie", "fsl,ls2088a-pcie";
+ reg = <0x00 0x03700000 0x0 0x00100000 /* controller registers */
+ 0x98 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
<GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
<GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
@@ -1200,26 +1200,26 @@ pcie4: pcie@3700000 {
#size-cells = <2>;
device_type = "pci";
dma-coherent;
- apio-wins = <8>;
- ppio-wins = <8>;
+ num-viewport = <8>;
bus-range = <0x0 0xff>;
- ranges = <0x82000000 0x0 0x40000000 0x98 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ ranges = <0x81000000 0x0 0x00000000 0x98 0x00010000 0x0 0x00010000
+ 0x82000000 0x0 0x40000000 0x98 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
msi-parent = <&its>;
+ iommu-map = <0 &smmu 0 1>; /* This is fixed-up by u-boot */
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 2 &gic 0 0 GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 3 &gic 0 0 GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 4 &gic 0 0 GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
- iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
status = "disabled";
};
pcie5: pcie@3800000 {
- compatible = "fsl,lx2160a-pcie";
- reg = <0x00 0x03800000 0x0 0x00100000>, /* controller registers */
- <0xa0 0x00000000 0x0 0x00002000>; /* configuration space */
- reg-names = "csr_axi_slave", "config_axi_slave";
+ compatible = "fsl,lx2160ar2-pcie", "fsl,ls2088a-pcie";
+ reg = <0x00 0x03800000 0x0 0x00100000 /* controller registers */
+ 0xa0 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
<GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
<GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
@@ -1228,26 +1228,26 @@ pcie5: pcie@3800000 {
#size-cells = <2>;
device_type = "pci";
dma-coherent;
- apio-wins = <256>;
- ppio-wins = <24>;
+ num-viewport = <256>;
bus-range = <0x0 0xff>;
- ranges = <0x82000000 0x0 0x40000000 0xa0 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ ranges = <0x81000000 0x0 0x00000000 0xa0 0x00010000 0x0 0x00010000
+ 0x82000000 0x0 0x40000000 0xa0 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
msi-parent = <&its>;
+ iommu-map = <0 &smmu 0 1>; /* This is fixed-up by u-boot */
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 2 &gic 0 0 GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 3 &gic 0 0 GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 4 &gic 0 0 GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
- iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
status = "disabled";
};
pcie6: pcie@3900000 {
- compatible = "fsl,lx2160a-pcie";
- reg = <0x00 0x03900000 0x0 0x00100000>, /* controller registers */
- <0xa8 0x00000000 0x0 0x00002000>; /* configuration space */
- reg-names = "csr_axi_slave", "config_axi_slave";
+ compatible = "fsl,lx2160ar2-pcie", "fsl,ls2088a-pcie";
+ reg = <0x00 0x03900000 0x0 0x00100000 /* controller registers */
+ 0xa8 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
@@ -1256,18 +1256,18 @@ pcie6: pcie@3900000 {
#size-cells = <2>;
device_type = "pci";
dma-coherent;
- apio-wins = <8>;
- ppio-wins = <8>;
+ num-viewport = <8>;
bus-range = <0x0 0xff>;
- ranges = <0x82000000 0x0 0x40000000 0xa8 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ ranges = <0x81000000 0x0 0x00000000 0xa8 0x00010000 0x0 0x00010000
+ 0x82000000 0x0 0x40000000 0xa8 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
msi-parent = <&its>;
+ iommu-map = <0 &smmu 0 1>; /* This is fixed-up by u-boot */
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 2 &gic 0 0 GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 3 &gic 0 0 GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
<0000 0 0 4 &gic 0 0 GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
- iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
status = "disabled";
};
--
2.37.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2022-08-17 20:27 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-08-17 20:25 [PATCH v4 0/2] lx216x DTS updates Li Yang
2022-08-17 20:25 ` Li Yang [this message]
2022-09-12 7:05 ` [PATCH v4 1/2] arm64: dts: lx2160a: update PCIe nodes to match rev2 silicon Olof Johansson
2022-09-12 18:54 ` Olof Johansson
2022-09-12 20:33 ` Russell King (Oracle)
2022-09-13 2:34 ` Olof Johansson
2022-09-12 20:25 ` Leo Li
2022-09-13 2:03 ` Shawn Guo
2022-09-12 21:49 ` Leo Li
2022-08-17 20:25 ` [PATCH v4 2/2] arm64: dts: lx2160a: add pcie EP mode nodes Li Yang
2022-08-22 3:35 ` [PATCH v4 0/2] lx216x DTS updates Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220817202538.21493-2-leoyang.li@nxp.com \
--to=leoyang.li@nxp.com \
--cc=Zhiqiang.Hou@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).