* [PATCH v2 0/9] Update UniPhier armv8 devicetree
@ 2022-09-12 7:15 Kunihiko Hayashi
2022-09-12 7:15 ` [PATCH v2 1/9] arm64: dts: uniphier: Rename pvtctl node to thermal-sensor Kunihiko Hayashi
` (8 more replies)
0 siblings, 9 replies; 10+ messages in thread
From: Kunihiko Hayashi @ 2022-09-12 7:15 UTC (permalink / raw)
To: soc, Arnd Bergmann, Olof Johansson
Cc: Rob Herring, Krzysztof Kozlowski, Masami Hiramatsu, devicetree,
linux-arm-kernel, linux-kernel, Kunihiko Hayashi
Update devicetree sources for UniPhier armv8 SoCs to remove dtschema
warnings, add support existing features that haven't yet been
described, and replace constants with macros.
Changes since v1:
- Exclue usb fixed patch (already applied)
- Describe the reason why removing generic pcie compatible
- Add L2 cache node patch
Kunihiko Hayashi (9):
arm64: dts: uniphier: Rename pvtctl node to thermal-sensor
arm64: dts: uniphier: Rename usb-phy node to usb-glue
arm64: dts: uniphier: Rename gpio-hog nodes
arm64: dts: uniphier: Use GIC interrupt definitions
arm64: dts: uniphier: Add ahci controller and glue layer nodes for
PXs3
arm64: dts: uniphier: Add USB-device support for PXs3 reference board
arm64: dts: uniphier: Fix opp-table node name for LD20
arm64: dts: uniphier: Remove compatible "snps,dw-pcie" from pcie node
arm64: dts: uniphier: Add L2 cache node
arch/arm/boot/dts/uniphier-pinctrl.dtsi | 10 ++
arch/arm64/boot/dts/socionext/Makefile | 4 +-
.../boot/dts/socionext/uniphier-ld11-ref.dts | 6 +-
.../boot/dts/socionext/uniphier-ld11.dtsi | 59 ++++---
.../dts/socionext/uniphier-ld20-akebi96.dts | 6 +-
.../boot/dts/socionext/uniphier-ld20-ref.dts | 6 +-
.../boot/dts/socionext/uniphier-ld20.dtsi | 80 ++++++----
.../socionext/uniphier-pxs3-ref-gadget0.dts | 41 +++++
.../socionext/uniphier-pxs3-ref-gadget1.dts | 40 +++++
.../boot/dts/socionext/uniphier-pxs3-ref.dts | 14 +-
.../boot/dts/socionext/uniphier-pxs3.dtsi | 148 ++++++++++++++----
11 files changed, 313 insertions(+), 101 deletions(-)
create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread* [PATCH v2 1/9] arm64: dts: uniphier: Rename pvtctl node to thermal-sensor 2022-09-12 7:15 [PATCH v2 0/9] Update UniPhier armv8 devicetree Kunihiko Hayashi @ 2022-09-12 7:15 ` Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 2/9] arm64: dts: uniphier: Rename usb-phy node to usb-glue Kunihiko Hayashi ` (7 subsequent siblings) 8 siblings, 0 replies; 10+ messages in thread From: Kunihiko Hayashi @ 2022-09-12 7:15 UTC (permalink / raw) To: soc, Arnd Bergmann, Olof Johansson Cc: Rob Herring, Krzysztof Kozlowski, Masami Hiramatsu, devicetree, linux-arm-kernel, linux-kernel, Kunihiko Hayashi The pvtctl node belongs to thermal-sensor, so the node name should be renamed to thermal-sensor. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> --- arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi | 2 +- arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi index 8f2c1c1e2c64..debab9f0e3e1 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi @@ -715,7 +715,7 @@ watchdog { compatible = "socionext,uniphier-wdt"; }; - pvtctl: pvtctl { + pvtctl: thermal-sensor { compatible = "socionext,uniphier-ld20-thermal"; interrupts = <0 3 4>; #thermal-sensor-cells = <0>; diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi index ba75adedbf79..e96e7ed98717 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi @@ -545,7 +545,7 @@ watchdog { compatible = "socionext,uniphier-wdt"; }; - pvtctl: pvtctl { + pvtctl: thermal-sensor { compatible = "socionext,uniphier-pxs3-thermal"; interrupts = <0 3 4>; #thermal-sensor-cells = <0>; -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 2/9] arm64: dts: uniphier: Rename usb-phy node to usb-glue 2022-09-12 7:15 [PATCH v2 0/9] Update UniPhier armv8 devicetree Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 1/9] arm64: dts: uniphier: Rename pvtctl node to thermal-sensor Kunihiko Hayashi @ 2022-09-12 7:15 ` Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 3/9] arm64: dts: uniphier: Rename gpio-hog nodes Kunihiko Hayashi ` (6 subsequent siblings) 8 siblings, 0 replies; 10+ messages in thread From: Kunihiko Hayashi @ 2022-09-12 7:15 UTC (permalink / raw) To: soc, Arnd Bergmann, Olof Johansson Cc: Rob Herring, Krzysztof Kozlowski, Masami Hiramatsu, devicetree, linux-arm-kernel, linux-kernel, Kunihiko Hayashi Actual phy nodes are each child node. The parent node should be usb-glue node. This applies to the devicetree for LD11 SoC. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> --- arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi index 15dcfc259854..6fa4de24526a 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi @@ -530,7 +530,7 @@ pinctrl: pinctrl { compatible = "socionext,uniphier-ld11-pinctrl"; }; - usb-phy { + usb-glue { compatible = "socionext,uniphier-ld11-usb2-phy"; #address-cells = <1>; #size-cells = <0>; -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 3/9] arm64: dts: uniphier: Rename gpio-hog nodes 2022-09-12 7:15 [PATCH v2 0/9] Update UniPhier armv8 devicetree Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 1/9] arm64: dts: uniphier: Rename pvtctl node to thermal-sensor Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 2/9] arm64: dts: uniphier: Rename usb-phy node to usb-glue Kunihiko Hayashi @ 2022-09-12 7:15 ` Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 4/9] arm64: dts: uniphier: Use GIC interrupt definitions Kunihiko Hayashi ` (5 subsequent siblings) 8 siblings, 0 replies; 10+ messages in thread From: Kunihiko Hayashi @ 2022-09-12 7:15 UTC (permalink / raw) To: soc, Arnd Bergmann, Olof Johansson Cc: Rob Herring, Krzysztof Kozlowski, Masami Hiramatsu, devicetree, linux-arm-kernel, linux-kernel, Kunihiko Hayashi According to gpio-hog schema, should add the suffix "-hog" to the node names including gpio-hog to fix the following warning. uniphier-ld11-ref.dtb: gpio@55000000: 'xirq0' does not match any of the regexes: '^.+-hog(-[0-9+)?$', 'pinctrl-[0-9]+' From schema: Documentation/devicetree/bindings/gpio/socionext,uniphier-gpio.yaml This applies to the devicetre for LD11, LD20 and PXs3 SoCs. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> --- arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts | 2 +- arch/arm64/boot/dts/socionext/uniphier-ld20-akebi96.dts | 4 ++-- arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts | 2 +- arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts | 2 +- 4 files changed, 5 insertions(+), 5 deletions(-) diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts index 617d2b1e9b1e..41b47f5d2ed7 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts +++ b/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts @@ -51,7 +51,7 @@ &serial0 { }; &gpio { - xirq0 { + xirq0-hog { gpio-hog; gpios = <UNIPHIER_GPIO_IRQ(0) 0>; input; diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20-akebi96.dts b/arch/arm64/boot/dts/socionext/uniphier-ld20-akebi96.dts index aa159a11292c..b55b70ded015 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld20-akebi96.dts +++ b/arch/arm64/boot/dts/socionext/uniphier-ld20-akebi96.dts @@ -168,12 +168,12 @@ &pcie { &gpio { /* IRQs for Max3421 */ - xirq0 { + xirq0-hog { gpio-hog; gpios = <UNIPHIER_GPIO_IRQ(0) 1>; input; }; - xirq10 { + xirq10-hog { gpio-hog; gpios = <UNIPHIER_GPIO_IRQ(10) 1>; input; diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts index 39ee279a1eb9..8c111588c9a1 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts +++ b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts @@ -51,7 +51,7 @@ &serial0 { }; &gpio { - xirq0 { + xirq0-hog { gpio-hog; gpios = <UNIPHIER_GPIO_IRQ(0) 0>; input; diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts index 086040306fb3..feb070f934e9 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts +++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts @@ -68,7 +68,7 @@ &serial3 { }; &gpio { - xirq4 { + xirq4-hog { gpio-hog; gpios = <UNIPHIER_GPIO_IRQ(4) 0>; input; -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 4/9] arm64: dts: uniphier: Use GIC interrupt definitions 2022-09-12 7:15 [PATCH v2 0/9] Update UniPhier armv8 devicetree Kunihiko Hayashi ` (2 preceding siblings ...) 2022-09-12 7:15 ` [PATCH v2 3/9] arm64: dts: uniphier: Rename gpio-hog nodes Kunihiko Hayashi @ 2022-09-12 7:15 ` Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 5/9] arm64: dts: uniphier: Add ahci controller and glue layer nodes for PXs3 Kunihiko Hayashi ` (4 subsequent siblings) 8 siblings, 0 replies; 10+ messages in thread From: Kunihiko Hayashi @ 2022-09-12 7:15 UTC (permalink / raw) To: soc, Arnd Bergmann, Olof Johansson Cc: Rob Herring, Krzysztof Kozlowski, Masami Hiramatsu, devicetree, linux-arm-kernel, linux-kernel, Kunihiko Hayashi Use human-readable definitions for GIC interrupt type and flag, instead of hard-coding the numbers. No functional change. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> --- .../boot/dts/socionext/uniphier-ld11-ref.dts | 4 +- .../boot/dts/socionext/uniphier-ld11.dtsi | 51 ++++++++-------- .../dts/socionext/uniphier-ld20-akebi96.dts | 2 +- .../boot/dts/socionext/uniphier-ld20-ref.dts | 4 +- .../boot/dts/socionext/uniphier-ld20.dtsi | 60 ++++++++++--------- .../boot/dts/socionext/uniphier-pxs3-ref.dts | 4 +- .../boot/dts/socionext/uniphier-pxs3.dtsi | 56 ++++++++--------- 7 files changed, 93 insertions(+), 88 deletions(-) diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts index 41b47f5d2ed7..414aeb99e68f 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts +++ b/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts @@ -39,11 +39,11 @@ memory@80000000 { }; ðsc { - interrupts = <0 8>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; }; &serialsc { - interrupts = <0 8>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; }; &serial0 { diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi index 6fa4de24526a..6a7d7973e9dd 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi @@ -7,6 +7,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/gpio/uniphier-gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> / { compatible = "socionext,uniphier-ld11"; @@ -102,10 +103,10 @@ emmc_pwrseq: emmc-pwrseq { timer { compatible = "arm,armv8-timer"; - interrupts = <1 13 4>, - <1 14 4>, - <1 11 4>, - <1 10 4>; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>, + <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>, + <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>; }; reserved-memory { @@ -131,7 +132,7 @@ spi0: spi@54006000 { reg = <0x54006000 0x100>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 39 4>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi0>; clocks = <&peri_clk 11>; @@ -144,7 +145,7 @@ spi1: spi@54006100 { reg = <0x54006100 0x100>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 216 4>; + interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi1>; clocks = <&peri_clk 12>; @@ -155,7 +156,7 @@ serial0: serial@54006800 { compatible = "socionext,uniphier-uart"; status = "disabled"; reg = <0x54006800 0x40>; - interrupts = <0 33 4>; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart0>; clocks = <&peri_clk 0>; @@ -166,7 +167,7 @@ serial1: serial@54006900 { compatible = "socionext,uniphier-uart"; status = "disabled"; reg = <0x54006900 0x40>; - interrupts = <0 35 4>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1>; clocks = <&peri_clk 1>; @@ -177,7 +178,7 @@ serial2: serial@54006a00 { compatible = "socionext,uniphier-uart"; status = "disabled"; reg = <0x54006a00 0x40>; - interrupts = <0 37 4>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart2>; clocks = <&peri_clk 2>; @@ -188,7 +189,7 @@ serial3: serial@54006b00 { compatible = "socionext,uniphier-uart"; status = "disabled"; reg = <0x54006b00 0x40>; - interrupts = <0 177 4>; + interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart3>; clocks = <&peri_clk 3>; @@ -223,7 +224,7 @@ gpio: gpio@55000000 { audio@56000000 { compatible = "socionext,uniphier-ld11-aio"; reg = <0x56000000 0x80000>; - interrupts = <0 144 4>; + interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_aout1>, <&pinctrl_aoutiec1>; @@ -323,7 +324,7 @@ i2c0: i2c@58780000 { reg = <0x58780000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 41 4>; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c0>; clocks = <&peri_clk 4>; @@ -337,7 +338,7 @@ i2c1: i2c@58781000 { reg = <0x58781000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 42 4>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c1>; clocks = <&peri_clk 5>; @@ -350,7 +351,7 @@ i2c2: i2c@58782000 { reg = <0x58782000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 43 4>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; clocks = <&peri_clk 6>; resets = <&peri_rst 6>; clock-frequency = <400000>; @@ -362,7 +363,7 @@ i2c3: i2c@58783000 { reg = <0x58783000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 44 4>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c3>; clocks = <&peri_clk 7>; @@ -376,7 +377,7 @@ i2c4: i2c@58784000 { reg = <0x58784000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 45 4>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c4>; clocks = <&peri_clk 8>; @@ -389,7 +390,7 @@ i2c5: i2c@58785000 { reg = <0x58785000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 25 4>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; clocks = <&peri_clk 9>; resets = <&peri_rst 9>; clock-frequency = <400000>; @@ -440,7 +441,7 @@ peri_rst: reset { emmc: mmc@5a000000 { compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc"; reg = <0x5a000000 0x400>; - interrupts = <0 78 4>; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_emmc>; clocks = <&sys_clk 4>; @@ -460,7 +461,7 @@ usb0: usb@5a800100 { compatible = "socionext,uniphier-ehci", "generic-ehci"; status = "disabled"; reg = <0x5a800100 0x100>; - interrupts = <0 243 4>; + interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usb0>; clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 8>, @@ -476,7 +477,7 @@ usb1: usb@5a810100 { compatible = "socionext,uniphier-ehci", "generic-ehci"; status = "disabled"; reg = <0x5a810100 0x100>; - interrupts = <0 244 4>; + interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usb1>; clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 9>, @@ -492,7 +493,7 @@ usb2: usb@5a820100 { compatible = "socionext,uniphier-ehci", "generic-ehci"; status = "disabled"; reg = <0x5a820100 0x100>; - interrupts = <0 245 4>; + interrupts = <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usb2>; clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 10>, @@ -573,7 +574,7 @@ efuse@200 { xdmac: dma-controller@5fc10000 { compatible = "socionext,uniphier-xdmac"; reg = <0x5fc10000 0x5300>; - interrupts = <0 188 4>; + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; dma-channels = <16>; #dma-cells = <2>; }; @@ -591,7 +592,7 @@ gic: interrupt-controller@5fe00000 { <0x5fe40000 0x80000>; /* GICR */ interrupt-controller; #interrupt-cells = <3>; - interrupts = <1 9 4>; + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; }; sysctrl@61840000 { @@ -618,7 +619,7 @@ eth: ethernet@65000000 { compatible = "socionext,uniphier-ld11-ave4"; status = "disabled"; reg = <0x65000000 0x8500>; - interrupts = <0 66 4>; + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; clock-names = "ether"; clocks = <&sys_clk 6>; reset-names = "ether"; @@ -640,7 +641,7 @@ nand: nand-controller@68000000 { reg = <0x68000000 0x20>, <0x68100000 0x1000>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 65 4>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; clock-names = "nand", "nand_x", "ecc"; diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20-akebi96.dts b/arch/arm64/boot/dts/socionext/uniphier-ld20-akebi96.dts index b55b70ded015..fba454adae7d 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld20-akebi96.dts +++ b/arch/arm64/boot/dts/socionext/uniphier-ld20-akebi96.dts @@ -110,7 +110,7 @@ usb-over-spi@0 { spi-max-frequency = <12500000>; interrupt-parent = <&gpio>; interrupt-names = "udc"; - interrupts = <0 2>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; }; }; diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts index 8c111588c9a1..a5f2083f8b75 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts +++ b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts @@ -39,11 +39,11 @@ memory@80000000 { }; ðsc { - interrupts = <0 8>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; }; &serialsc { - interrupts = <0 8>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; }; &serial0 { diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi index debab9f0e3e1..62e5892b4f8e 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi @@ -7,6 +7,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/gpio/uniphier-gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/thermal/thermal.h> / { @@ -176,10 +177,10 @@ emmc_pwrseq: emmc-pwrseq { timer { compatible = "arm,armv8-timer"; - interrupts = <1 13 4>, - <1 14 4>, - <1 11 4>, - <1 10 4>; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>, + <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>, + <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>; }; thermal-zones { @@ -236,7 +237,7 @@ spi0: spi@54006000 { reg = <0x54006000 0x100>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 39 4>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi0>; clocks = <&peri_clk 11>; @@ -249,7 +250,7 @@ spi1: spi@54006100 { reg = <0x54006100 0x100>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 216 4>; + interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi1>; clocks = <&peri_clk 12>; @@ -262,7 +263,7 @@ spi2: spi@54006200 { reg = <0x54006200 0x100>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 229 4>; + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi2>; clocks = <&peri_clk 13>; @@ -275,7 +276,7 @@ spi3: spi@54006300 { reg = <0x54006300 0x100>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 230 4>; + interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi3>; clocks = <&peri_clk 14>; @@ -286,7 +287,7 @@ serial0: serial@54006800 { compatible = "socionext,uniphier-uart"; status = "disabled"; reg = <0x54006800 0x40>; - interrupts = <0 33 4>; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart0>; clocks = <&peri_clk 0>; @@ -297,7 +298,7 @@ serial1: serial@54006900 { compatible = "socionext,uniphier-uart"; status = "disabled"; reg = <0x54006900 0x40>; - interrupts = <0 35 4>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1>; clocks = <&peri_clk 1>; @@ -308,7 +309,7 @@ serial2: serial@54006a00 { compatible = "socionext,uniphier-uart"; status = "disabled"; reg = <0x54006a00 0x40>; - interrupts = <0 37 4>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart2>; clocks = <&peri_clk 2>; @@ -319,7 +320,7 @@ serial3: serial@54006b00 { compatible = "socionext,uniphier-uart"; status = "disabled"; reg = <0x54006b00 0x40>; - interrupts = <0 177 4>; + interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart3>; clocks = <&peri_clk 3>; @@ -348,7 +349,7 @@ gpio: gpio@55000000 { audio@56000000 { compatible = "socionext,uniphier-ld20-aio"; reg = <0x56000000 0x80000>; - interrupts = <0 144 4>; + interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_aout1>, <&pinctrl_aoutiec1>; @@ -448,7 +449,7 @@ i2c0: i2c@58780000 { reg = <0x58780000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 41 4>; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c0>; clocks = <&peri_clk 4>; @@ -462,7 +463,7 @@ i2c1: i2c@58781000 { reg = <0x58781000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 42 4>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c1>; clocks = <&peri_clk 5>; @@ -475,7 +476,7 @@ i2c2: i2c@58782000 { reg = <0x58782000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 43 4>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; clocks = <&peri_clk 6>; resets = <&peri_rst 6>; clock-frequency = <400000>; @@ -487,7 +488,7 @@ i2c3: i2c@58783000 { reg = <0x58783000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 44 4>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c3>; clocks = <&peri_clk 7>; @@ -501,7 +502,7 @@ i2c4: i2c@58784000 { reg = <0x58784000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 45 4>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c4>; clocks = <&peri_clk 8>; @@ -514,7 +515,7 @@ i2c5: i2c@58785000 { reg = <0x58785000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 25 4>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; clocks = <&peri_clk 9>; resets = <&peri_rst 9>; clock-frequency = <400000>; @@ -570,7 +571,7 @@ peri_rst: reset { emmc: mmc@5a000000 { compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc"; reg = <0x5a000000 0x400>; - interrupts = <0 78 4>; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_emmc>; clocks = <&sys_clk 4>; @@ -590,7 +591,7 @@ sd: mmc@5a400000 { compatible = "socionext,uniphier-sd-v3.1.1"; status = "disabled"; reg = <0x5a400000 0x800>; - interrupts = <0 76 4>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sd>; clocks = <&sd_clk 0>; @@ -675,7 +676,7 @@ usb_hs_i2: trim@5a,0 { xdmac: dma-controller@5fc10000 { compatible = "socionext,uniphier-xdmac"; reg = <0x5fc10000 0x5300>; - interrupts = <0 188 4>; + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; dma-channels = <16>; #dma-cells = <2>; }; @@ -693,7 +694,7 @@ gic: interrupt-controller@5fe00000 { <0x5fe80000 0x80000>; /* GICR */ interrupt-controller; #interrupt-cells = <3>; - interrupts = <1 9 4>; + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; }; sysctrl@61840000 { @@ -717,7 +718,7 @@ watchdog { pvtctl: thermal-sensor { compatible = "socionext,uniphier-ld20-thermal"; - interrupts = <0 3 4>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; #thermal-sensor-cells = <0>; socionext,tmod-calibration = <0x0f22 0x68ee>; }; @@ -727,7 +728,7 @@ eth: ethernet@65000000 { compatible = "socionext,uniphier-ld20-ave4"; status = "disabled"; reg = <0x65000000 0x8500>; - interrupts = <0 66 4>; + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ether_rgmii>; clock-names = "ether"; @@ -749,7 +750,7 @@ usb: usb@65a00000 { status = "disabled"; reg = <0x65a00000 0xcd00>; interrupt-names = "host"; - interrupts = <0 134 4>; + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb1>, <&pinctrl_usb2>, <&pinctrl_usb3>; @@ -915,7 +916,8 @@ pcie: pcie@66000000 { <0x82000000 0 0x20000000 0x20000000 0 0x0ffe0000>; #interrupt-cells = <1>; interrupt-names = "dma", "msi"; - interrupts = <0 224 4>, <0 225 4>; + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */ <0 0 0 2 &pcie_intc 1>, /* INTB */ @@ -928,7 +930,7 @@ pcie_intc: legacy-interrupt-controller { interrupt-controller; #interrupt-cells = <1>; interrupt-parent = <&gic>; - interrupts = <0 226 4>; + interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; }; }; @@ -950,7 +952,7 @@ nand: nand-controller@68000000 { reg = <0x68000000 0x20>, <0x68100000 0x1000>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 65 4>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; clock-names = "nand", "nand_x", "ecc"; diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts index feb070f934e9..506c7b9ff50d 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts +++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts @@ -40,11 +40,11 @@ memory@80000000 { }; ðsc { - interrupts = <4 8>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; }; &serialsc { - interrupts = <4 8>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; }; &spi0 { diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi index e96e7ed98717..7304dee2e504 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi @@ -7,6 +7,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/gpio/uniphier-gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/thermal/thermal.h> / { @@ -135,10 +136,10 @@ emmc_pwrseq: emmc-pwrseq { timer { compatible = "arm,armv8-timer"; - interrupts = <1 13 4>, - <1 14 4>, - <1 11 4>, - <1 10 4>; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>, + <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>, + <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>; }; thermal-zones { @@ -195,7 +196,7 @@ spi0: spi@54006000 { reg = <0x54006000 0x100>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 39 4>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi0>; clocks = <&peri_clk 11>; @@ -208,7 +209,7 @@ spi1: spi@54006100 { reg = <0x54006100 0x100>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 216 4>; + interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi1>; clocks = <&peri_clk 12>; @@ -219,7 +220,7 @@ serial0: serial@54006800 { compatible = "socionext,uniphier-uart"; status = "disabled"; reg = <0x54006800 0x40>; - interrupts = <0 33 4>; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart0>; clocks = <&peri_clk 0>; @@ -230,7 +231,7 @@ serial1: serial@54006900 { compatible = "socionext,uniphier-uart"; status = "disabled"; reg = <0x54006900 0x40>; - interrupts = <0 35 4>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1>; clocks = <&peri_clk 1>; @@ -241,7 +242,7 @@ serial2: serial@54006a00 { compatible = "socionext,uniphier-uart"; status = "disabled"; reg = <0x54006a00 0x40>; - interrupts = <0 37 4>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart2>; clocks = <&peri_clk 2>; @@ -252,7 +253,7 @@ serial3: serial@54006b00 { compatible = "socionext,uniphier-uart"; status = "disabled"; reg = <0x54006b00 0x40>; - interrupts = <0 177 4>; + interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart3>; clocks = <&peri_clk 3>; @@ -284,7 +285,7 @@ i2c0: i2c@58780000 { reg = <0x58780000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 41 4>; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c0>; clocks = <&peri_clk 4>; @@ -298,7 +299,7 @@ i2c1: i2c@58781000 { reg = <0x58781000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 42 4>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c1>; clocks = <&peri_clk 5>; @@ -312,7 +313,7 @@ i2c2: i2c@58782000 { reg = <0x58782000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 43 4>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c2>; clocks = <&peri_clk 6>; @@ -326,7 +327,7 @@ i2c3: i2c@58783000 { reg = <0x58783000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 44 4>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c3>; clocks = <&peri_clk 7>; @@ -340,7 +341,7 @@ i2c6: i2c@58786000 { reg = <0x58786000 0x80>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 26 4>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clocks = <&peri_clk 10>; resets = <&peri_rst 10>; clock-frequency = <400000>; @@ -396,7 +397,7 @@ peri_rst: reset { emmc: mmc@5a000000 { compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc"; reg = <0x5a000000 0x400>; - interrupts = <0 78 4>; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_emmc>; clocks = <&sys_clk 4>; @@ -416,7 +417,7 @@ sd: mmc@5a400000 { compatible = "socionext,uniphier-sd-v3.1.1"; status = "disabled"; reg = <0x5a400000 0x800>; - interrupts = <0 76 4>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default", "uhs"; pinctrl-0 = <&pinctrl_sd>; pinctrl-1 = <&pinctrl_sd_uhs>; @@ -505,7 +506,7 @@ usb_hs_i2: trim@5a,0 { xdmac: dma-controller@5fc10000 { compatible = "socionext,uniphier-xdmac"; reg = <0x5fc10000 0x5300>; - interrupts = <0 188 4>; + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; dma-channels = <16>; #dma-cells = <2>; }; @@ -523,7 +524,7 @@ gic: interrupt-controller@5fe00000 { <0x5fe80000 0x80000>; /* GICR */ interrupt-controller; #interrupt-cells = <3>; - interrupts = <1 9 4>; + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; }; sysctrl@61840000 { @@ -547,7 +548,7 @@ watchdog { pvtctl: thermal-sensor { compatible = "socionext,uniphier-pxs3-thermal"; - interrupts = <0 3 4>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; #thermal-sensor-cells = <0>; socionext,tmod-calibration = <0x0f22 0x68ee>; }; @@ -557,7 +558,7 @@ eth0: ethernet@65000000 { compatible = "socionext,uniphier-pxs3-ave4"; status = "disabled"; reg = <0x65000000 0x8500>; - interrupts = <0 66 4>; + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ether_rgmii>; clock-names = "ether"; @@ -578,7 +579,7 @@ eth1: ethernet@65200000 { compatible = "socionext,uniphier-pxs3-ave4"; status = "disabled"; reg = <0x65200000 0x8500>; - interrupts = <0 67 4>; + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ether1_rgmii>; clock-names = "ether"; @@ -600,7 +601,7 @@ usb0: usb@65a00000 { status = "disabled"; reg = <0x65a00000 0xcd00>; interrupt-names = "dwc_usb3"; - interrupts = <0 134 4>; + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb2>; clock-names = "ref", "bus_early", "suspend"; @@ -702,7 +703,7 @@ usb1: usb@65c00000 { status = "disabled"; reg = <0x65c00000 0xcd00>; interrupt-names = "dwc_usb3"; - interrupts = <0 137 4>; + interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usb1>, <&pinctrl_usb3>; clock-names = "ref", "bus_early", "suspend"; @@ -812,7 +813,8 @@ pcie: pcie@66000000 { <0x82000000 0 0x20000000 0x20000000 0 0x0ffe0000>; #interrupt-cells = <1>; interrupt-names = "dma", "msi"; - interrupts = <0 224 4>, <0 225 4>; + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */ <0 0 0 2 &pcie_intc 1>, /* INTB */ @@ -825,7 +827,7 @@ pcie_intc: legacy-interrupt-controller { interrupt-controller; #interrupt-cells = <1>; interrupt-parent = <&gic>; - interrupts = <0 226 4>; + interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; }; }; @@ -847,7 +849,7 @@ nand: nand-controller@68000000 { reg = <0x68000000 0x20>, <0x68100000 0x1000>; #address-cells = <1>; #size-cells = <0>; - interrupts = <0 65 4>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; clock-names = "nand", "nand_x", "ecc"; -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 5/9] arm64: dts: uniphier: Add ahci controller and glue layer nodes for PXs3 2022-09-12 7:15 [PATCH v2 0/9] Update UniPhier armv8 devicetree Kunihiko Hayashi ` (3 preceding siblings ...) 2022-09-12 7:15 ` [PATCH v2 4/9] arm64: dts: uniphier: Use GIC interrupt definitions Kunihiko Hayashi @ 2022-09-12 7:15 ` Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 6/9] arm64: dts: uniphier: Add USB-device support for PXs3 reference board Kunihiko Hayashi ` (3 subsequent siblings) 8 siblings, 0 replies; 10+ messages in thread From: Kunihiko Hayashi @ 2022-09-12 7:15 UTC (permalink / raw) To: soc, Arnd Bergmann, Olof Johansson Cc: Rob Herring, Krzysztof Kozlowski, Masami Hiramatsu, devicetree, linux-arm-kernel, linux-kernel, Kunihiko Hayashi Add ahci controller and glue layer nodes including reset and phy. This supports for PXs3 and the boards. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> --- .../boot/dts/socionext/uniphier-pxs3-ref.dts | 8 ++ .../boot/dts/socionext/uniphier-pxs3.dtsi | 80 +++++++++++++++++++ 2 files changed, 88 insertions(+) diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts index 506c7b9ff50d..1ced6190ab2b 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts +++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts @@ -137,6 +137,14 @@ nand@0 { }; }; +&ahci0 { + status = "okay"; +}; + +&ahci1 { + status = "okay"; +}; + &pinctrl_ether_rgmii { tx { pins = "RGMII0_TXCLK", "RGMII0_TXD0", "RGMII0_TXD1", diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi index 7304dee2e504..f49a8db3e918 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi @@ -596,6 +596,86 @@ mdio1: mdio { }; }; + ahci0: ahci@65600000 { + compatible = "socionext,uniphier-pxs3-ahci", + "generic-ahci"; + status = "disabled"; + reg = <0x65600000 0x10000>; + interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sys_clk 28>; + resets = <&sys_rst 28>, <&ahci0_rst 0>; + ports-implemented = <1>; + phys = <&ahci0_phy>; + }; + + ahci-glue@65700000 { + compatible = "socionext,uniphier-pxs3-ahci-glue", + "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x65700000 0x100>; + + ahci0_rst: reset@0 { + compatible = "socionext,uniphier-pxs3-ahci-reset"; + reg = <0x0 0x4>; + clock-names = "link"; + clocks = <&sys_clk 28>; + reset-names = "link"; + resets = <&sys_rst 28>; + #reset-cells = <1>; + }; + + ahci0_phy: phy@10 { + compatible = "socionext,uniphier-pxs3-ahci-phy"; + reg = <0x10 0x10>; + clock-names = "link", "phy"; + clocks = <&sys_clk 28>, <&sys_clk 30>; + reset-names = "link", "phy"; + resets = <&sys_rst 28>, <&sys_rst 30>; + #phy-cells = <0>; + }; + }; + + ahci1: ahci@65800000 { + compatible = "socionext,uniphier-pxs3-ahci", + "generic-ahci"; + status = "disabled"; + reg = <0x65800000 0x10000>; + interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sys_clk 29>; + resets = <&sys_rst 29>, <&ahci1_rst 0>; + ports-implemented = <1>; + phys = <&ahci1_phy>; + }; + + ahci-glue@65900000 { + compatible = "socionext,uniphier-pxs3-ahci-glue", + "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x65900000 0x100>; + + ahci1_rst: reset@0 { + compatible = "socionext,uniphier-pxs3-ahci-reset"; + reg = <0x0 0x4>; + clock-names = "link"; + clocks = <&sys_clk 29>; + reset-names = "link"; + resets = <&sys_rst 29>; + #reset-cells = <1>; + }; + + ahci1_phy: phy@10 { + compatible = "socionext,uniphier-pxs3-ahci-phy"; + reg = <0x10 0x10>; + clock-names = "link", "phy"; + clocks = <&sys_clk 29>, <&sys_clk 30>; + reset-names = "link", "phy"; + resets = <&sys_rst 29>, <&sys_rst 30>; + #phy-cells = <0>; + }; + }; + usb0: usb@65a00000 { compatible = "socionext,uniphier-dwc3", "snps,dwc3"; status = "disabled"; -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 6/9] arm64: dts: uniphier: Add USB-device support for PXs3 reference board 2022-09-12 7:15 [PATCH v2 0/9] Update UniPhier armv8 devicetree Kunihiko Hayashi ` (4 preceding siblings ...) 2022-09-12 7:15 ` [PATCH v2 5/9] arm64: dts: uniphier: Add ahci controller and glue layer nodes for PXs3 Kunihiko Hayashi @ 2022-09-12 7:15 ` Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 7/9] arm64: dts: uniphier: Fix opp-table node name for LD20 Kunihiko Hayashi ` (2 subsequent siblings) 8 siblings, 0 replies; 10+ messages in thread From: Kunihiko Hayashi @ 2022-09-12 7:15 UTC (permalink / raw) To: soc, Arnd Bergmann, Olof Johansson Cc: Rob Herring, Krzysztof Kozlowski, Masami Hiramatsu, devicetree, linux-arm-kernel, linux-kernel, Kunihiko Hayashi PXs3 reference board can change each USB port 0 and 1 to device mode with jumpers. Prepare devicetree sources for USB port 0 and 1. This specifies dr_mode, pinctrl, and some quirks and removes nodes for unused phys and vbus-supply properties. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> --- arch/arm/boot/dts/uniphier-pinctrl.dtsi | 10 +++++ arch/arm64/boot/dts/socionext/Makefile | 4 +- .../socionext/uniphier-pxs3-ref-gadget0.dts | 41 +++++++++++++++++++ .../socionext/uniphier-pxs3-ref-gadget1.dts | 40 ++++++++++++++++++ 4 files changed, 94 insertions(+), 1 deletion(-) create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts diff --git a/arch/arm/boot/dts/uniphier-pinctrl.dtsi b/arch/arm/boot/dts/uniphier-pinctrl.dtsi index c0fd029b37e5..f909ec2e5333 100644 --- a/arch/arm/boot/dts/uniphier-pinctrl.dtsi +++ b/arch/arm/boot/dts/uniphier-pinctrl.dtsi @@ -196,11 +196,21 @@ pinctrl_usb0: usb0 { function = "usb0"; }; + pinctrl_usb0_device: usb0-device { + groups = "usb0_device"; + function = "usb0"; + }; + pinctrl_usb1: usb1 { groups = "usb1"; function = "usb1"; }; + pinctrl_usb1_device: usb1-device { + groups = "usb1_device"; + function = "usb1"; + }; + pinctrl_usb2: usb2 { groups = "usb2"; function = "usb2"; diff --git a/arch/arm64/boot/dts/socionext/Makefile b/arch/arm64/boot/dts/socionext/Makefile index dda3da33614b..33989a9643ac 100644 --- a/arch/arm64/boot/dts/socionext/Makefile +++ b/arch/arm64/boot/dts/socionext/Makefile @@ -5,4 +5,6 @@ dtb-$(CONFIG_ARCH_UNIPHIER) += \ uniphier-ld20-akebi96.dtb \ uniphier-ld20-global.dtb \ uniphier-ld20-ref.dtb \ - uniphier-pxs3-ref.dtb + uniphier-pxs3-ref.dtb \ + uniphier-pxs3-ref-gadget0.dtb \ + uniphier-pxs3-ref-gadget1.dtb diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts new file mode 100644 index 000000000000..7069f51bc120 --- /dev/null +++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts @@ -0,0 +1,41 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +// +// Device Tree Source for UniPhier PXs3 Reference Board (for USB-Device #0) +// +// Copyright (C) 2021 Socionext Inc. +// Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> + +/dts-v1/; +#include "uniphier-pxs3-ref.dts" + +/ { + model = "UniPhier PXs3 Reference Board (USB-Device #0)"; +}; + +/* I2C3 pinctrl is shared with USB*VBUSIN */ +&i2c3 { + status = "disabled"; +}; + +&usb0 { + status = "okay"; + dr_mode = "peripheral"; + pinctrl-0 = <&pinctrl_usb0_device>; + snps,dis_enblslpm_quirk; + snps,dis_u2_susphy_quirk; + snps,dis_u3_susphy_quirk; + snps,usb2_gadget_lpm_disable; + phy-names = "usb2-phy", "usb3-phy"; + phys = <&usb0_hsphy0>, <&usb0_ssphy0>; +}; + +&usb0_hsphy0 { + /delete-property/ vbus-supply; +}; + +&usb0_ssphy0 { + /delete-property/ vbus-supply; +}; + +/delete-node/ &usb0_hsphy1; +/delete-node/ &usb0_ssphy1; diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts new file mode 100644 index 000000000000..a3cfa8113ffb --- /dev/null +++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts @@ -0,0 +1,40 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +// +// Device Tree Source for UniPhier PXs3 Reference Board (for USB-Device #1) +// +// Copyright (C) 2021 Socionext Inc. +// Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> + +/dts-v1/; +#include "uniphier-pxs3-ref.dts" + +/ { + model = "UniPhier PXs3 Reference Board (USB-Device #1)"; +}; + +/* I2C3 pinctrl is shared with USB*VBUSIN */ +&i2c3 { + status = "disabled"; +}; + +&usb1 { + status = "okay"; + dr_mode = "peripheral"; + pinctrl-0 = <&pinctrl_usb1_device>; + snps,dis_enblslpm_quirk; + snps,dis_u2_susphy_quirk; + snps,dis_u3_susphy_quirk; + snps,usb2_gadget_lpm_disable; + phy-names = "usb2-phy", "usb3-phy"; + phys = <&usb1_hsphy0>, <&usb1_ssphy0>; +}; + +&usb1_hsphy0 { + /delete-property/ vbus-supply; +}; + +&usb1_ssphy0 { + /delete-property/ vbus-supply; +}; + +/delete-node/ &usb1_hsphy1; -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 7/9] arm64: dts: uniphier: Fix opp-table node name for LD20 2022-09-12 7:15 [PATCH v2 0/9] Update UniPhier armv8 devicetree Kunihiko Hayashi ` (5 preceding siblings ...) 2022-09-12 7:15 ` [PATCH v2 6/9] arm64: dts: uniphier: Add USB-device support for PXs3 reference board Kunihiko Hayashi @ 2022-09-12 7:15 ` Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 8/9] arm64: dts: uniphier: Remove compatible "snps,dw-pcie" from pcie node Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 9/9] arm64: dts: uniphier: Add L2 cache node Kunihiko Hayashi 8 siblings, 0 replies; 10+ messages in thread From: Kunihiko Hayashi @ 2022-09-12 7:15 UTC (permalink / raw) To: soc, Arnd Bergmann, Olof Johansson Cc: Rob Herring, Krzysztof Kozlowski, Masami Hiramatsu, devicetree, linux-arm-kernel, linux-kernel, Kunihiko Hayashi To fix dtbs_check warning: uniphier-ld20-akebi96.dt.yaml: opp-table0: $nodename:0: 'opp-table0' does not match '^opp-table(-[a-z0-9]+)?$' From schema: Documentation/devicetree/bindings/opp/opp-v2.yaml Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> --- arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi index 62e5892b4f8e..0d75a90d1342 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi @@ -81,7 +81,7 @@ cpu3: cpu@101 { }; }; - cluster0_opp: opp-table0 { + cluster0_opp: opp-table-0 { compatible = "operating-points-v2"; opp-shared; @@ -119,7 +119,7 @@ opp-1100000000 { }; }; - cluster1_opp: opp-table1 { + cluster1_opp: opp-table-1 { compatible = "operating-points-v2"; opp-shared; -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 8/9] arm64: dts: uniphier: Remove compatible "snps,dw-pcie" from pcie node 2022-09-12 7:15 [PATCH v2 0/9] Update UniPhier armv8 devicetree Kunihiko Hayashi ` (6 preceding siblings ...) 2022-09-12 7:15 ` [PATCH v2 7/9] arm64: dts: uniphier: Fix opp-table node name for LD20 Kunihiko Hayashi @ 2022-09-12 7:15 ` Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 9/9] arm64: dts: uniphier: Add L2 cache node Kunihiko Hayashi 8 siblings, 0 replies; 10+ messages in thread From: Kunihiko Hayashi @ 2022-09-12 7:15 UTC (permalink / raw) To: soc, Arnd Bergmann, Olof Johansson Cc: Rob Herring, Krzysztof Kozlowski, Masami Hiramatsu, devicetree, linux-arm-kernel, linux-kernel, Kunihiko Hayashi The generic platform driver pcie-designware-plat.c doesn't work for UniPhier PCIe host controller, because the controller has some necessary initialization sequence for the controller-specific logic. Currently the controller doesn't use "snps,dw-pcie" compatible, so this is no longer needed. Remove the compatible string from the pcie node. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> --- arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi | 2 +- arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi index 0d75a90d1342..e24784e12b7b 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi @@ -896,7 +896,7 @@ usb_ssphy1: ss-phy@310 { }; pcie: pcie@66000000 { - compatible = "socionext,uniphier-pcie", "snps,dw-pcie"; + compatible = "socionext,uniphier-pcie"; status = "disabled"; reg-names = "dbi", "link", "config"; reg = <0x66000000 0x1000>, <0x66010000 0x10000>, diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi index f49a8db3e918..6277be04a974 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi @@ -873,7 +873,7 @@ usb1_ssphy0: ss-phy@300 { }; pcie: pcie@66000000 { - compatible = "socionext,uniphier-pcie", "snps,dw-pcie"; + compatible = "socionext,uniphier-pcie"; status = "disabled"; reg-names = "dbi", "link", "config"; reg = <0x66000000 0x1000>, <0x66010000 0x10000>, -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 9/9] arm64: dts: uniphier: Add L2 cache node 2022-09-12 7:15 [PATCH v2 0/9] Update UniPhier armv8 devicetree Kunihiko Hayashi ` (7 preceding siblings ...) 2022-09-12 7:15 ` [PATCH v2 8/9] arm64: dts: uniphier: Remove compatible "snps,dw-pcie" from pcie node Kunihiko Hayashi @ 2022-09-12 7:15 ` Kunihiko Hayashi 8 siblings, 0 replies; 10+ messages in thread From: Kunihiko Hayashi @ 2022-09-12 7:15 UTC (permalink / raw) To: soc, Arnd Bergmann, Olof Johansson Cc: Rob Herring, Krzysztof Kozlowski, Masami Hiramatsu, devicetree, linux-arm-kernel, linux-kernel, Kunihiko Hayashi Add a L2 cache node referenced from CPU nodes as the missing cache hierarchy information because the following warning was issued. cacheinfo: Unable to detect cache hierarchy for CPU 0 Early cacheinfo failed, ret = -2 Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> --- arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi | 6 ++++++ arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi | 12 ++++++++++++ arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi | 8 ++++++++ 3 files changed, 26 insertions(+) diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi index 6a7d7973e9dd..a75356db006b 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi @@ -36,6 +36,7 @@ cpu0: cpu@0 { reg = <0 0x000>; clocks = <&sys_clk 33>; enable-method = "psci"; + next-level-cache = <&l2>; operating-points-v2 = <&cluster0_opp>; }; @@ -45,8 +46,13 @@ cpu1: cpu@1 { reg = <0 0x001>; clocks = <&sys_clk 33>; enable-method = "psci"; + next-level-cache = <&l2>; operating-points-v2 = <&cluster0_opp>; }; + + l2: l2-cache { + compatible = "cache"; + }; }; cluster0_opp: opp-table { diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi index e24784e12b7b..1e6317e371ba 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi @@ -46,6 +46,7 @@ cpu0: cpu@0 { reg = <0 0x000>; clocks = <&sys_clk 32>; enable-method = "psci"; + next-level-cache = <&a72_l2>; operating-points-v2 = <&cluster0_opp>; #cooling-cells = <2>; }; @@ -56,6 +57,7 @@ cpu1: cpu@1 { reg = <0 0x001>; clocks = <&sys_clk 32>; enable-method = "psci"; + next-level-cache = <&a72_l2>; operating-points-v2 = <&cluster0_opp>; #cooling-cells = <2>; }; @@ -66,6 +68,7 @@ cpu2: cpu@100 { reg = <0 0x100>; clocks = <&sys_clk 33>; enable-method = "psci"; + next-level-cache = <&a53_l2>; operating-points-v2 = <&cluster1_opp>; #cooling-cells = <2>; }; @@ -76,9 +79,18 @@ cpu3: cpu@101 { reg = <0 0x101>; clocks = <&sys_clk 33>; enable-method = "psci"; + next-level-cache = <&a53_l2>; operating-points-v2 = <&cluster1_opp>; #cooling-cells = <2>; }; + + a72_l2: l2-cache0 { + compatible = "cache"; + }; + + a53_l2: l2-cache1 { + compatible = "cache"; + }; }; cluster0_opp: opp-table-0 { diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi index 6277be04a974..72ba6a52233e 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi @@ -43,6 +43,7 @@ cpu0: cpu@0 { reg = <0 0x000>; clocks = <&sys_clk 33>; enable-method = "psci"; + next-level-cache = <&l2>; operating-points-v2 = <&cluster0_opp>; #cooling-cells = <2>; }; @@ -53,6 +54,7 @@ cpu1: cpu@1 { reg = <0 0x001>; clocks = <&sys_clk 33>; enable-method = "psci"; + next-level-cache = <&l2>; operating-points-v2 = <&cluster0_opp>; #cooling-cells = <2>; }; @@ -63,6 +65,7 @@ cpu2: cpu@2 { reg = <0 0x002>; clocks = <&sys_clk 33>; enable-method = "psci"; + next-level-cache = <&l2>; operating-points-v2 = <&cluster0_opp>; #cooling-cells = <2>; }; @@ -73,9 +76,14 @@ cpu3: cpu@3 { reg = <0 0x003>; clocks = <&sys_clk 33>; enable-method = "psci"; + next-level-cache = <&l2>; operating-points-v2 = <&cluster0_opp>; #cooling-cells = <2>; }; + + l2: l2-cache { + compatible = "cache"; + }; }; cluster0_opp: opp-table { -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 10+ messages in thread
end of thread, other threads:[~2022-09-12 7:26 UTC | newest] Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2022-09-12 7:15 [PATCH v2 0/9] Update UniPhier armv8 devicetree Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 1/9] arm64: dts: uniphier: Rename pvtctl node to thermal-sensor Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 2/9] arm64: dts: uniphier: Rename usb-phy node to usb-glue Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 3/9] arm64: dts: uniphier: Rename gpio-hog nodes Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 4/9] arm64: dts: uniphier: Use GIC interrupt definitions Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 5/9] arm64: dts: uniphier: Add ahci controller and glue layer nodes for PXs3 Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 6/9] arm64: dts: uniphier: Add USB-device support for PXs3 reference board Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 7/9] arm64: dts: uniphier: Fix opp-table node name for LD20 Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 8/9] arm64: dts: uniphier: Remove compatible "snps,dw-pcie" from pcie node Kunihiko Hayashi 2022-09-12 7:15 ` [PATCH v2 9/9] arm64: dts: uniphier: Add L2 cache node Kunihiko Hayashi
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).