* [PATCH v3 3/3] arm64: dts: freescale: Add InnoComm i.MX8MM based WB15 SoM and EVK
2022-09-19 8:24 [PATCH v3 0/3] arm64: dts: Add InnoComm WB15-EVK support Sascha Hauer
2022-09-19 8:24 ` [PATCH v3 1/3] dt-bindings: vendor-prefixes: Add prefix for InnoComm Sascha Hauer
2022-09-19 8:24 ` [PATCH v3 2/3] dt-bindings: arm: fsl: Add InnoComm WB15 EVK Sascha Hauer
@ 2022-09-19 8:24 ` Sascha Hauer
2022-09-19 10:53 ` Krzysztof Kozlowski
2 siblings, 1 reply; 6+ messages in thread
From: Sascha Hauer @ 2022-09-19 8:24 UTC (permalink / raw)
To: devicetree; +Cc: Rob Herring, linux-arm-kernel, kernel, Sascha Hauer
Add the InnoComm i.MX8MM based WB15 SoM and its EVK. The WB15 is a
half credit card sized board featuring:
- i.MX8MM CPU
- LPDDR4, 1GiB
- eMMC, 8GiB
- 1Gb Ethernet RGMII interface
- WiFi 802.11 a/b/g/n/ac, Bluetooth 4.2
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
Notes:
Changes since v3:
- no underscores in node names
- use IRQ_TYPE_LEVEL_LOW for specifying GPIO interrupt polarity
Changes since v2:
- Fix remaining s/innocom/innocomm/
Changes since v1:
- Fix spelling of InnoComm
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../freescale/imx8mm-innocomm-wb15-evk.dts | 147 ++++++
.../dts/freescale/imx8mm-innocomm-wb15.dtsi | 480 ++++++++++++++++++
3 files changed, 628 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15-evk.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 8bf7f7ecebaa1..387746c8d8dc2 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -55,6 +55,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-emcon-avari.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-innocomm-wb15-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-mx8menlo.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15-evk.dts
new file mode 100644
index 0000000000000..08c29326aefaa
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15-evk.dts
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2018 Bang & Olufsen
+ * Copyright 2022 Pengutronix
+ */
+
+/dts-v1/;
+
+#include "imx8mm-innocomm-wb15.dtsi"
+
+/ {
+ model = "InnoComm WB15-EVK";
+ compatible = "innocomm,wb15-evk", "fsl,imx8mm";
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+ status = "okay";
+
+ led-0 {
+ label = "debug";
+ gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ reg_vsd_3v3: regulator-vsd-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_vsd_3v3>;
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_ethphy: regulator-eth-phy {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec_phy_reg>;
+ regulator-name = "PHY_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy0>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec_phy>;
+ reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ phy-supply = <®_ethphy>;
+ };
+ };
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usbotg1 {
+ dr_mode = "otg";
+ samsung,picophy-pre-emp-curr-control = <3>;
+ samsung,picophy-dc-vol-level-adjust = <7>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ samsung,picophy-pre-emp-curr-control = <3>;
+ samsung,picophy-dc-vol-level-adjust = <7>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc2 {
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_vsd_3v3>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_fec: fec-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x03
+ MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x03
+ MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ >;
+ };
+
+ pinctrl_fec_phy: fec-phy-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
+ >;
+ };
+
+ pinctrl_fec_phy_reg: fec-phy-reg-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x16
+ >;
+ };
+
+ pinctrl_gpio_leds: led-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3 0xd6
+ >;
+ };
+
+ pinctrl_reg_vsd_3v3: reg-vsd-3v3-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41
+ >;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi
new file mode 100644
index 0000000000000..59be159315942
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi
@@ -0,0 +1,480 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2018 Bang & Olufsen
+ */
+
+#include "imx8mm.dtsi"
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+
+/ {
+ reg_modem: regulator-modem {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_modem_regulator>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "epdev_on";
+ gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ reg_3v3_out: regulator-3v3-out {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3_OUT";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&cpu_alert0 {
+ temperature = <95000>;
+};
+
+&cpu_crit0 {
+ temperature = <105000>;
+};
+
+&ddrc {
+ operating-points-v2 = <&ddrc_opp_table>;
+
+ ddrc_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-25000000 {
+ opp-hz = /bits/ 64 <25000000>;
+ };
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ };
+
+ opp-600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ pmic@4b {
+ compatible = "rohm,bd71847";
+ reg = <0x4b>;
+ pinctrl-0 = <&pinctrl_pmic>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+ rohm,reset-snvs-powered;
+
+ regulators {
+ buck1_reg: BUCK1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <850000>;
+ rohm,dvs-idle-voltage = <850000>;
+ rohm,dvs-suspend-voltage = <850000>;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "buck2";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <1000000>;
+ rohm,dvs-idle-voltage = <900000>;
+ };
+
+ buck3_reg: BUCK3 {
+ // buck5 in datasheet
+ regulator-name = "buck3";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck4_reg: BUCK4 {
+ // buck6 in datasheet
+ regulator-name = "buck4";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck5_reg: BUCK5 {
+ // buck7 in datasheet
+ regulator-name = "buck5";
+ regulator-min-microvolt = <1605000>;
+ regulator-max-microvolt = <1995000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck6_reg: BUCK6 {
+ // buck8 in datasheet
+ regulator-name = "buck6";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: LDO1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "ldo5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "ldo6";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+&pcie_phy {
+ fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_OUTPUT>;
+ fsl,tx-deemph-gen1 = <0x2d>;
+ fsl,tx-deemph-gen2 = <0xf>;
+ status = "okay";
+};
+
+&pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie0>;
+ reset-gpio = <&gpio5 21 GPIO_ACTIVE_LOW>;
+ clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_PHY>,
+ <&clk IMX8MM_CLK_PCIE1_AUX>;
+ clock-names = "pcie", "pcie_bus", "pcie_aux";
+ fsl,max-link-speed = <1>;
+ assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>;
+ assigned-clock-rates = <10000000>, <250000000>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>, <&clk IMX8MM_SYS_PLL2_250M>;
+ status = "okay";
+};
+
+&uart1 { /* BT */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ assigned-clocks = <&clk IMX8MM_CLK_UART1>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+ fsl,uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm4349-bt";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_modem_bt>;
+ device-wakeup-gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+ vbat-supply = <®_3v3_out>;
+ vddio-supply = <®_3v3_out>;
+ clocks = <&osc_32k>;
+ max-speed = <3000000>;
+ clock-names = "extclk";
+ };
+};
+
+&uart2 { /* console */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ bus-width = <8>;
+ no-sd;
+ no-sdio;
+ non-removable;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ bus-width = <4>;
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_1 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_2 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_3 {
+ cpu-supply = <&buck2_reg>;
+};
+
+/delete-node/ &sec_jr1; /* Job ring in use by OP-TEE */
+
+&iomuxc {
+ pinctrl_i2c1: i2c1-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_i2c1_gpio: i2c1-gpio-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14 0x400001c3
+ MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15 0x400001c3
+ >;
+ };
+
+ pinctrl_i2c2: i2c2-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2-gpio-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16 0x400001c3
+ MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17 0x400001c3
+ >;
+ };
+
+ pinctrl_i2c3: i2c3-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3-gpio-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18 0x400001c3
+ MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19 0x400001c3
+ >;
+ };
+
+ pinctrl_pcie0: pcie0-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B 0x61
+ MX8MM_IOMUXC_I2C4_SDA_GPIO5_IO21 0x6
+ >;
+ };
+
+ pinctrl_modem_bt: modem-bt-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_CLE_GPIO3_IO5 0x19
+ MX8MM_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x19
+ MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x19
+ MX8MM_IOMUXC_NAND_RE_B_GPIO3_IO15 0x19
+ MX8MM_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x141
+ >;
+ };
+
+ pinctrl_modem_regulator: modem-reg-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x41
+ >;
+ };
+
+ pinctrl_pmic: pmic-irq-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41
+ >;
+ };
+
+ pinctrl_uart1: uart1-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140
+ MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140
+ MX8MM_IOMUXC_UART3_RXD_UART1_DCE_CTS_B 0x140
+ MX8MM_IOMUXC_UART3_TXD_UART1_DCE_RTS_B 0x140
+ >;
+ };
+
+ pinctrl_uart2: uart2-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
+ MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x40000190
+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0
+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0
+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0
+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0
+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0
+ MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0
+ MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0
+ MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0
+ MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0
+ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x190
+ MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x40000194
+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4
+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4
+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4
+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4
+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4
+ MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4
+ MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4
+ MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4
+ MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4
+ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x194
+ MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d4
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x40000196
+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6
+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6
+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6
+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6
+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6
+ MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6
+ MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6
+ MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6
+ MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6
+ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x196
+ MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d6
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2-gpio-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_wdog: wdog-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 6+ messages in thread