[PATCH v5 0/4] thermal: mediatek: Add support for MT8365 SoC

[PATCH v5 0/4] thermal: mediatek: Add support for MT8365 SoC

[Amjad Ouled-Ameur]

This patchset adds thermal support for MT8365 SoC which contains three
thermal sensors.

Changes in V5:
- rebased on thermal/linux-next

Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
---
Amjad Ouled-Ameur (1):
      thermal: mediatek: add another get_temp ops for thermal sensors

Fabien Parent (2):
      dt-bindings: thermal: mediatek: add binding documentation for MT8365 SoC
      thermal: mediatek: add support for MT8365 SoC

Markus Schneider-Pargmann (1):
      thermal: mediatek: control buffer enablement tweaks

 .../bindings/thermal/mediatek-thermal.txt          |   1 +
 drivers/thermal/mtk_thermal.c                      | 197 +++++++++++++++++----
 2 files changed, 166 insertions(+), 32 deletions(-)
---
base-commit: 64b269c002273cac4c41fb69572f3684dd1e3284
change-id: 20220920-i350-thermal-up-23edef139b6b

Best regards,
-- 
Amjad Ouled-Ameur <aouledameur@baylibre.com>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 1/4] dt-bindings: thermal: mediatek: add binding documentation for MT8365 SoC

[Amjad Ouled-Ameur]

From: Fabien Parent <fparent@baylibre.com>

Add the binding documentation for the thermal support on MT8365 SoC.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>

diff --git a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt
index 5c7e7bdd029a..ba4ebffeade4 100644
--- a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt
@@ -14,6 +14,7 @@ Required properties:
   - "mediatek,mt2712-thermal" : For MT2712 family of SoCs
   - "mediatek,mt7622-thermal" : For MT7622 SoC
   - "mediatek,mt8183-thermal" : For MT8183 family of SoCs
+  - "mediatek,mt8365-thermal" : For MT8365 family of SoCs
   - "mediatek,mt8516-thermal", "mediatek,mt2701-thermal : For MT8516 family of SoCs
 - reg: Address range of the thermal controller
 - interrupts: IRQ for the thermal controller

-- 
b4 0.10.0

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 2/4] thermal: mediatek: control buffer enablement tweaks

[Amjad Ouled-Ameur]

From: Markus Schneider-Pargmann <msp@baylibre.com>

Add logic in order to be able to turn on the control buffer on MT8365.
This change now allows to have control buffer support for MTK_THERMAL_V1,
and it allows to define the register offset, and mask used to enable it.

Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>

diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
index 8440692e3890..d8ddceb75372 100644
--- a/drivers/thermal/mtk_thermal.c
+++ b/drivers/thermal/mtk_thermal.c
@@ -271,6 +271,9 @@ struct mtk_thermal_data {
 	bool need_switch_bank;
 	struct thermal_bank_cfg bank_data[MAX_NUM_ZONES];
 	enum mtk_thermal_version version;
+	u32 apmixed_buffer_ctl_reg;
+	u32 apmixed_buffer_ctl_mask;
+	u32 apmixed_buffer_ctl_set;
 };
 
 struct mtk_thermal {
@@ -514,6 +517,9 @@ static const struct mtk_thermal_data mt7622_thermal_data = {
 	.adcpnp = mt7622_adcpnp,
 	.sensor_mux_values = mt7622_mux_values,
 	.version = MTK_THERMAL_V2,
+	.apmixed_buffer_ctl_reg = APMIXED_SYS_TS_CON1,
+	.apmixed_buffer_ctl_mask = GENMASK(31, 6) | BIT(3),
+	.apmixed_buffer_ctl_set = BIT(0),
 };
 
 /*
@@ -963,14 +969,18 @@ static const struct of_device_id mtk_thermal_of_match[] = {
 };
 MODULE_DEVICE_TABLE(of, mtk_thermal_of_match);
 
-static void mtk_thermal_turn_on_buffer(void __iomem *apmixed_base)
+static void mtk_thermal_turn_on_buffer(struct mtk_thermal *mt,
+				       void __iomem *apmixed_base)
 {
-	int tmp;
+	u32 tmp;
+
+	if (!mt->conf->apmixed_buffer_ctl_reg)
+		return;
 
-	tmp = readl(apmixed_base + APMIXED_SYS_TS_CON1);
-	tmp &= ~(0x37);
-	tmp |= 0x1;
-	writel(tmp, apmixed_base + APMIXED_SYS_TS_CON1);
+	tmp = readl(apmixed_base + mt->conf->apmixed_buffer_ctl_reg);
+	tmp &= mt->conf->apmixed_buffer_ctl_mask;
+	tmp |= mt->conf->apmixed_buffer_ctl_set;
+	writel(tmp, apmixed_base + mt->conf->apmixed_buffer_ctl_reg);
 	udelay(200);
 }
 
@@ -1070,8 +1080,9 @@ static int mtk_thermal_probe(struct platform_device *pdev)
 		goto err_disable_clk_auxadc;
 	}
 
+	mtk_thermal_turn_on_buffer(mt, apmixed_base);
+
 	if (mt->conf->version == MTK_THERMAL_V2) {
-		mtk_thermal_turn_on_buffer(apmixed_base);
 		mtk_thermal_release_periodic_ts(mt, auxadc_base);
 	}
 

-- 
b4 0.10.0

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 3/4] thermal: mediatek: add support for MT8365 SoC

[Amjad Ouled-Ameur]

From: Fabien Parent <fparent@baylibre.com>

MT8365 is similar to the other SoCs supported by the driver. It has only
one bank and 3 actual sensors that can be multiplexed. There is another
one sensor that does not have usable data.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
index d8ddceb75372..3a5df1440822 100644
--- a/drivers/thermal/mtk_thermal.c
+++ b/drivers/thermal/mtk_thermal.c
@@ -31,6 +31,7 @@
 #define AUXADC_CON2_V		0x010
 #define AUXADC_DATA(channel)	(0x14 + (channel) * 4)
 
+#define APMIXED_SYS_TS_CON0	0x600
 #define APMIXED_SYS_TS_CON1	0x604
 
 /* Thermal Controller Registers */
@@ -245,6 +246,17 @@ enum mtk_thermal_version {
 /* The calibration coefficient of sensor  */
 #define MT8183_CALIBRATION	153
 
+/* MT8365 */
+#define MT8365_TEMP_AUXADC_CHANNEL 11
+#define MT8365_CALIBRATION 164
+#define MT8365_NUM_CONTROLLER 1
+#define MT8365_NUM_BANKS 1
+#define MT8365_NUM_SENSORS 3
+#define MT8365_NUM_SENSORS_PER_ZONE 3
+#define MT8365_TS1 0
+#define MT8365_TS2 1
+#define MT8365_TS3 2
+
 struct mtk_thermal;
 
 struct thermal_bank_cfg {
@@ -389,6 +401,24 @@ static const int mt7622_mux_values[MT7622_NUM_SENSORS] = { 0, };
 static const int mt7622_vts_index[MT7622_NUM_SENSORS] = { VTS1 };
 static const int mt7622_tc_offset[MT7622_NUM_CONTROLLER] = { 0x0, };
 
+/* MT8365 thermal sensor data */
+static const int mt8365_bank_data[MT8365_NUM_SENSORS] = {
+	MT8365_TS1, MT8365_TS2, MT8365_TS3
+};
+
+static const int mt8365_msr[MT8365_NUM_SENSORS_PER_ZONE] = {
+	TEMP_MSR0, TEMP_MSR1, TEMP_MSR2
+};
+
+static const int mt8365_adcpnp[MT8365_NUM_SENSORS_PER_ZONE] = {
+	TEMP_ADCPNP0, TEMP_ADCPNP1, TEMP_ADCPNP2
+};
+
+static const int mt8365_mux_values[MT8365_NUM_SENSORS] = { 0, 1, 2 };
+static const int mt8365_tc_offset[MT8365_NUM_CONTROLLER] = { 0 };
+
+static const int mt8365_vts_index[MT8365_NUM_SENSORS] = { VTS1, VTS2, VTS3 };
+
 /*
  * The MT8173 thermal controller has four banks. Each bank can read up to
  * four temperature sensors simultaneously. The MT8173 has a total of 5
@@ -463,6 +493,40 @@ static const struct mtk_thermal_data mt2701_thermal_data = {
 	.version = MTK_THERMAL_V1,
 };
 
+/*
+ * The MT8365 thermal controller has one bank, which can read up to
+ * four temperature sensors simultaneously. The MT8365 has a total of 3
+ * temperature sensors.
+ *
+ * The thermal core only gets the maximum temperature of this one bank,
+ * so the bank concept wouldn't be necessary here. However, the SVS (Smart
+ * Voltage Scaling) unit makes its decisions based on the same bank
+ * data.
+ */
+static const struct mtk_thermal_data mt8365_thermal_data = {
+	.auxadc_channel = MT8365_TEMP_AUXADC_CHANNEL,
+	.num_banks = MT8365_NUM_BANKS,
+	.num_sensors = MT8365_NUM_SENSORS,
+	.vts_index = mt8365_vts_index,
+	.cali_val = MT8365_CALIBRATION,
+	.num_controller = MT8365_NUM_CONTROLLER,
+	.controller_offset = mt8365_tc_offset,
+	.need_switch_bank = false,
+	.bank_data = {
+		{
+			.num_sensors = MT8365_NUM_SENSORS,
+			.sensors = mt8365_bank_data
+		},
+	},
+	.msr = mt8365_msr,
+	.adcpnp = mt8365_adcpnp,
+	.sensor_mux_values = mt8365_mux_values,
+	.version = MTK_THERMAL_V1,
+	.apmixed_buffer_ctl_reg = APMIXED_SYS_TS_CON0,
+	.apmixed_buffer_ctl_mask = (u32) ~GENMASK(29, 28),
+	.apmixed_buffer_ctl_set = 0,
+};
+
 /*
  * The MT2712 thermal controller has one bank, which can read up to
  * four temperature sensors simultaneously. The MT2712 has a total of 4
@@ -964,6 +1028,10 @@ static const struct of_device_id mtk_thermal_of_match[] = {
 	{
 		.compatible = "mediatek,mt8183-thermal",
 		.data = (void *)&mt8183_thermal_data,
+	},
+	{
+		.compatible = "mediatek,mt8365-thermal",
+		.data = (void *)&mt8365_thermal_data,
 	}, {
 	},
 };

-- 
b4 0.10.0

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 4/4] thermal: mediatek: add another get_temp ops for thermal sensors

[Amjad Ouled-Ameur]

Provide thermal zone to read thermal sensor in the SoC. We can read all the
thermal sensors value in the SoC by the node /sys/class/thermal/

In mtk_thermal_bank_temperature, return -EAGAIN instead of -EACCESS
on the first read of sensor that often are bogus values.
This can avoid following warning on boot:

  thermal thermal_zone6: failed to read out thermal zone (-13)

Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
index 3a5df1440822..311ad611fdab 100644
--- a/drivers/thermal/mtk_thermal.c
+++ b/drivers/thermal/mtk_thermal.c
@@ -259,6 +259,11 @@ enum mtk_thermal_version {
 
 struct mtk_thermal;
 
+struct mtk_thermal_zone {
+	struct mtk_thermal *mt;
+	int id;
+};
+
 struct thermal_bank_cfg {
 	unsigned int num_sensors;
 	const int *sensors;
@@ -307,6 +312,8 @@ struct mtk_thermal {
 
 	const struct mtk_thermal_data *conf;
 	struct mtk_thermal_bank banks[MAX_NUM_ZONES];
+
+	int (*raw_to_mcelsius)(struct mtk_thermal *mt, int sensno, s32 raw);
 };
 
 /* MT8183 thermal sensor data */
@@ -709,6 +716,29 @@ static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank)
 		mutex_unlock(&mt->lock);
 }
 
+static int _get_sensor_temp(struct mtk_thermal *mt, int id)
+{
+	u32 raw;
+	int temp;
+
+	const struct mtk_thermal_data *conf = mt->conf;
+
+	raw = readl(mt->thermal_base + conf->msr[id]);
+
+	temp = mt->raw_to_mcelsius(mt, id, raw);
+
+	/*
+	 * The first read of a sensor often contains very high bogus
+	 * temperature value. Filter these out so that the system does
+	 * not immediately shut down.
+	 */
+
+	if (temp > 200000)
+		return -EAGAIN;
+	else
+		return temp;
+}
+
 /**
  * mtk_thermal_bank_temperature - get the temperature of a bank
  * @bank:	The bank
@@ -721,26 +751,9 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
 	struct mtk_thermal *mt = bank->mt;
 	const struct mtk_thermal_data *conf = mt->conf;
 	int i, temp = INT_MIN, max = INT_MIN;
-	u32 raw;
 
 	for (i = 0; i < conf->bank_data[bank->id].num_sensors; i++) {
-		raw = readl(mt->thermal_base + conf->msr[i]);
-
-		if (mt->conf->version == MTK_THERMAL_V1) {
-			temp = raw_to_mcelsius_v1(
-				mt, conf->bank_data[bank->id].sensors[i], raw);
-		} else {
-			temp = raw_to_mcelsius_v2(
-				mt, conf->bank_data[bank->id].sensors[i], raw);
-		}
-
-		/*
-		 * The first read of a sensor often contains very high bogus
-		 * temperature value. Filter these out so that the system does
-		 * not immediately shut down.
-		 */
-		if (temp > 200000)
-			temp = 0;
+		temp = _get_sensor_temp(mt, i);
 
 		if (temp > max)
 			max = temp;
@@ -749,9 +762,10 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
 	return max;
 }
 
-static int mtk_read_temp(struct thermal_zone_device *tz, int *temperature)
+static int mtk_read_temp(struct thermal_zone_device *tzdev, int *temperature)
 {
-	struct mtk_thermal *mt = tz->devdata;
+	struct mtk_thermal_zone *tz = tzdev->devdata;
+	struct mtk_thermal *mt = tz->mt;
 	int i;
 	int tempmax = INT_MIN;
 
@@ -770,10 +784,28 @@ static int mtk_read_temp(struct thermal_zone_device *tz, int *temperature)
 	return 0;
 }
 
+static int mtk_read_sensor_temp(struct thermal_zone_device *tzdev, int *temperature)
+{
+	struct mtk_thermal_zone *tz = tzdev->devdata;
+	struct mtk_thermal *mt = tz->mt;
+	int id = tz->id - 1;
+
+	if (id < 0)
+		return -EACCES;
+
+	*temperature = _get_sensor_temp(mt, id);
+
+	return 0;
+}
+
 static const struct thermal_zone_device_ops mtk_thermal_ops = {
 	.get_temp = mtk_read_temp,
 };
 
+static const struct thermal_zone_device_ops mtk_thermal_sensor_ops = {
+	.get_temp = mtk_read_sensor_temp,
+};
+
 static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
 				  u32 apmixed_phys_base, u32 auxadc_phys_base,
 				  int ctrl_id)
@@ -1072,6 +1104,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
 	u64 auxadc_phys_base, apmixed_phys_base;
 	struct thermal_zone_device *tzdev;
 	void __iomem *apmixed_base, *auxadc_base;
+	struct mtk_thermal_zone *tz;
 
 	mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
 	if (!mt)
@@ -1150,6 +1183,9 @@ static int mtk_thermal_probe(struct platform_device *pdev)
 
 	mtk_thermal_turn_on_buffer(mt, apmixed_base);
 
+	mt->raw_to_mcelsius = (mt->conf->version == MTK_THERMAL_V1) ?
+				raw_to_mcelsius_v1 : raw_to_mcelsius_v2;
+
 	if (mt->conf->version == MTK_THERMAL_V2) {
 		mtk_thermal_release_periodic_ts(mt, auxadc_base);
 	}
@@ -1161,11 +1197,29 @@ static int mtk_thermal_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, mt);
 
-	tzdev = devm_thermal_of_zone_register(&pdev->dev, 0, mt,
-					      &mtk_thermal_ops);
-	if (IS_ERR(tzdev)) {
-		ret = PTR_ERR(tzdev);
-		goto err_disable_clk_peri_therm;
+	for (i = 0; i < mt->conf->num_sensors + 1; i++) {
+		tz = devm_kmalloc(&pdev->dev, sizeof(*tz), GFP_KERNEL);
+		if (!tz)
+			return -ENOMEM;
+
+		tz->mt = mt;
+		tz->id = i;
+
+		tzdev = devm_thermal_of_zone_register(&pdev->dev, i, tz, (i == 0) ?
+							     &mtk_thermal_ops :
+							     &mtk_thermal_sensor_ops);
+
+		if (IS_ERR(tzdev)) {
+			if (PTR_ERR(tzdev) == -ENODEV) {
+				dev_warn(&pdev->dev,
+					 "sensor %d not registered in thermal zone in dt\n", i);
+				continue;
+			}
+			if (PTR_ERR(tzdev) == -EACCES) {
+				ret = PTR_ERR(tzdev);
+				goto err_disable_clk_peri_therm;
+			}
+		}
 	}
 
 	ret = devm_thermal_add_hwmon_sysfs(tzdev);

-- 
b4 0.10.0

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 2/4] thermal: mediatek: control buffer enablement tweaks

[AngeloGioacchino Del Regno]

Il 20/09/22 17:03, Amjad Ouled-Ameur ha scritto:
> From: Markus Schneider-Pargmann <msp@baylibre.com>
> 
> Add logic in order to be able to turn on the control buffer on MT8365.
> This change now allows to have control buffer support for MTK_THERMAL_V1,
> and it allows to define the register offset, and mask used to enable it.
> 
> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
> Signed-off-by: Fabien Parent <fparent@baylibre.com>
> Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel