From: Christoph Niedermaier <cniedermaier@dh-electronics.com>
To: <linux-arm-kernel@lists.infradead.org>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Peng Fan <peng.fan@nxp.com>, Shawn Guo <shawnguo@kernel.org>,
Marek Vasut <marex@denx.de>, Fabio Estevam <festevam@denx.de>,
NXP Linux Team <linux-imx@nxp.com>, <kernel@dh-electronics.com>
Subject: [PATCH V2 3/4] ARM: dts: imx6ull-dhcom: Add DHCOM based PicoITX board
Date: Wed, 23 Nov 2022 18:36:00 +0100 [thread overview]
Message-ID: <20221123173601.13291-3-cniedermaier@dh-electronics.com> (raw)
In-Reply-To: <20221123173601.13291-1-cniedermaier@dh-electronics.com>
Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LED and a custom
board-to-board expansion connector. For this board a DHCOM i.MX6ULL
SoM configuration without WiFi/BT is used. The interface is used
for the SD card instead. Make this adjustment by using a separate DT
include file.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
---
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
---
V2: - Reorder comments in front of a block
- Reorder compatible and reg to the beginning of a node
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6ull-dhcom-picoitx.dts | 101 +++++++++++++++++++++
.../arm/boot/dts/imx6ull-dhcom-som-cfg-sdcard.dtsi | 97 ++++++++++++++++++++
3 files changed, 199 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ull-dhcom-picoitx.dts
create mode 100644 arch/arm/boot/dts/imx6ull-dhcom-som-cfg-sdcard.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 2cdc53211fc9..ecd8a91a83c1 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -740,6 +740,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ull-colibri-wifi-iris.dtb \
imx6ull-colibri-wifi-iris-v2.dtb \
imx6ull-dhcom-pdk2.dtb \
+ imx6ull-dhcom-picoitx.dtb \
imx6ull-jozacp.dtb \
imx6ull-kontron-bl.dtb \
imx6ull-myir-mys-6ulx-eval.dtb \
diff --git a/arch/arm/boot/dts/imx6ull-dhcom-picoitx.dts b/arch/arm/boot/dts/imx6ull-dhcom-picoitx.dts
new file mode 100644
index 000000000000..132b8b76ec84
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-dhcom-picoitx.dts
@@ -0,0 +1,101 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2022 DH electronics GmbH
+ *
+ * DHCOM iMX6ULL variant:
+ * DHCM-iMX6ULL-C080-R051-F0409-SPI-E2-CAN2-SD-RTC-ADC-I-01D2
+ * DHCOR PCB number: 578-200 or newer
+ * DHCOM PCB number: 579-200 or newer
+ * PicoITX PCB number: 487-600 or newer
+ */
+/dts-v1/;
+
+#include "imx6ull-dhcom-som.dtsi"
+#include "imx6ull-dhcom-som-cfg-sdcard.dtsi"
+
+/ {
+ model = "DH electronics i.MX6ULL DHCOM on PicoITX";
+ compatible = "dh,imx6ull-dhcom-picoitx", "dh,imx6ull-dhcom-som",
+ "dh,imx6ull-dhcor-som", "fsl,imx6ull";
+
+ led {
+ compatible = "gpio-leds";
+
+ led-0 {
+ color = <LED_COLOR_ID_YELLOW>;
+ default-state = "off";
+ function = LED_FUNCTION_INDICATOR;
+ gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO I */
+ };
+ };
+};
+
+&fec1 {
+ phy-handle = <&mdio1_phy0>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio1_phy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-id0007.c0f0", /* SMSC LAN8710Ai */
+ "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ clock-names = "rmii-ref";
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&pinctrl_fec1_phy &pinctrl_snvs_fec1_phy>;
+ pinctrl-names = "default";
+ reset-assert-us = <500>;
+ reset-deassert-us = <500>;
+ reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+ smsc,disable-energy-detect; /* Make plugin detection reliable */
+ };
+ };
+};
+
+&fec2 {
+ status = "disabled";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "PicoITX-HW2", "PicoITX-HW1", "DHCOM-M",
+ "PicoITX-HW0", "DHCOM-U", "DHCOM-T", "DHCOM-S",
+ "DHCOM-R", "DHCOM-Q", "DHCOM-P", "DHCOM-O",
+ "DHCOM-N", "", "", "";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "DHCOM-A", "DHCOM-B", "PicoITX-In2", "PicoITX-Out2",
+ "PicoITX-In1", "", "", "PicoITX-Out1",
+ "DHCOM-G", "DHCOM-H", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "";
+};
+
+&iomuxc {
+ pinctrl_fec1: fec1-grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b010
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b010
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b010
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b010
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6ull-dhcom-som-cfg-sdcard.dtsi b/arch/arm/boot/dts/imx6ull-dhcom-som-cfg-sdcard.dtsi
new file mode 100644
index 000000000000..5b095bf072cc
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-dhcom-som-cfg-sdcard.dtsi
@@ -0,0 +1,97 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2022 DH electronics GmbH
+ */
+
+/*
+ * Special SoM configuration: SD card
+ *
+ * Enabled: Micro SD card on module or
+ * external SD card via DHCOM depends on hardware variant
+ * GPIO H and GPIO I will be available
+ * DHCOM UART2 will be available
+ * Disabled: WiFi and BT
+ */
+
+/*
+ * To use usdhc1 as SD card, the WiFi node must be deleted.
+ * BT is also not available, so remove BT from the UART node.
+ */
+/delete-node/ &brcmf;
+/delete-node/ &bluetooth;
+
+/ {
+ aliases {
+ mmc1 = &usdhc1;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart4;
+ serial4 = &uart5;
+ serial5 = &uart6;
+ };
+
+ reg_sd1_vmmc: regulator-sd1-vmmc {
+ compatible = "regulator-fixed";
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "VSD_3V3";
+ };
+};
+
+/* Micro SD card on module or external SD card via DHCOM */
+&usdhc1 {
+ /delete-property/ #address-cells;
+ /delete-property/ #size-cells;
+ /delete-property/ keep-power-in-suspend;
+ /delete-property/ mmc-pwrseq;
+ /delete-property/ non-removable;
+ /delete-property/ wakeup-source;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ vmmc-supply = <®_sd1_vmmc>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_usdhc1: usdhc1-grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x120b0 /* SD1 CD */
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x120b0 /* SD1 CD */
+
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x120b0 /* SD1 CD */
+ >;
+ };
+};
--
2.11.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2022-11-23 18:14 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-11-23 17:35 [PATCH V2 1/4] dt-bindings: arm: fsl: Add PDK2, PicoITX and DRC02 boards for the DHCOM i.MX6ULL SoM Christoph Niedermaier
2022-11-23 17:35 ` [PATCH V2 2/4] ARM: dts: imx6ull-dhcom: Add DH electronics DHCOM i.MX6ULL SoM and PDK2 board Christoph Niedermaier
2022-12-31 10:01 ` Shawn Guo
2022-11-23 17:36 ` Christoph Niedermaier [this message]
2022-11-23 17:36 ` [PATCH V2 4/4] ARM: dts: imx6ull-dhcom: Add DHSOM based DRC02 board Christoph Niedermaier
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20221123173601.13291-3-cniedermaier@dh-electronics.com \
--to=cniedermaier@dh-electronics.com \
--cc=festevam@denx.de \
--cc=kernel@dh-electronics.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=marex@denx.de \
--cc=peng.fan@nxp.com \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).