* [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files
@ 2023-03-07 18:39 Stefan Wahren
2023-03-07 18:39 ` [PATCH V2 1/9] ARM: dts: imx28-apf28: Convert to use label references Stefan Wahren
` (9 more replies)
0 siblings, 10 replies; 11+ messages in thread
From: Stefan Wahren @ 2023-03-07 18:39 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: linux-imx, devicetree, linux-arm-kernel, Stefan Wahren
Since the imx28 belongs to the early ARM platforms which has been
adapted to DT, a lot of these DTS files are not in the best shape.
So this series tries to address this by using label references
and SPDX tags.
Theses patches doesn't include functional changes. The resulting
DTB files has been verified with dtdiff.
Changes in V2:
- fix alphabetical order of i2c label reference in patch 1
- add Wolfgang Grandegger in Cc for patch 2
- replace Anson's address in patch 7 with linux-imx@nxp.com because
his address isn't available anymore
- remove Cc from patch 8 because the address isn't available anymore
- add Acked-by for patch 9
Stefan Wahren (9):
ARM: dts: imx28-apf28: Convert to use label references
ARM: dts: imx28-m28/sps1: Convert to use label references
ARM: dts: imx28-apx4devkit: Convert to use label references
ARM: dts: imx28-cfa10036: Convert to use label references
ARM: dts: imx28-duckbill: Convert to use label references
ARM: dts: imx28-duckbill-2: Include base board
ARM: dts: imx28-evk: Convert to use label references
ARM: dts: imx28-ts4600: Convert to use label references
ARM: dts: imx28-tx28: add SPDX-License-Identifier
arch/arm/boot/dts/imx28-apf28.dts | 96 ++--
arch/arm/boot/dts/imx28-apf28dev.dts | 312 ++++++------
arch/arm/boot/dts/imx28-apx4devkit.dts | 380 +++++++-------
arch/arm/boot/dts/imx28-cfa10036.dts | 193 ++++----
arch/arm/boot/dts/imx28-cfa10049.dts | 454 +++++++++--------
arch/arm/boot/dts/imx28-cfa10055.dts | 224 +++++----
arch/arm/boot/dts/imx28-cfa10056.dts | 146 +++---
arch/arm/boot/dts/imx28-cfa10057.dts | 252 +++++-----
arch/arm/boot/dts/imx28-cfa10058.dts | 186 ++++---
arch/arm/boot/dts/imx28-duckbill-2-485.dts | 174 +------
.../arm/boot/dts/imx28-duckbill-2-enocean.dts | 198 +-------
arch/arm/boot/dts/imx28-duckbill-2-spi.dts | 211 ++------
arch/arm/boot/dts/imx28-duckbill-2.dts | 256 +++++-----
arch/arm/boot/dts/imx28-duckbill.dts | 196 ++++----
arch/arm/boot/dts/imx28-evk.dts | 462 +++++++++---------
arch/arm/boot/dts/imx28-m28.dtsi | 44 +-
arch/arm/boot/dts/imx28-m28cu3.dts | 354 +++++++-------
arch/arm/boot/dts/imx28-m28evk.dts | 420 ++++++++--------
arch/arm/boot/dts/imx28-sps1.dts | 201 ++++----
arch/arm/boot/dts/imx28-ts4600.dts | 80 ++-
arch/arm/boot/dts/imx28-tx28.dts | 38 +-
21 files changed, 2142 insertions(+), 2735 deletions(-)
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH V2 1/9] ARM: dts: imx28-apf28: Convert to use label references
2023-03-07 18:39 [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files Stefan Wahren
@ 2023-03-07 18:39 ` Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 2/9] ARM: dts: imx28-m28/sps1: " Stefan Wahren
` (8 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Stefan Wahren @ 2023-03-07 18:39 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: linux-imx, devicetree, linux-arm-kernel, Stefan Wahren, support
These Armadeus board files still use node name and unit address
to reference parts from the imx28.dtsi . This causes a lot of
redundancy. So use label references in order to make it easier
to maintain.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: <support@armadeus.com>
---
arch/arm/boot/dts/imx28-apf28.dts | 96 ++++-----
arch/arm/boot/dts/imx28-apf28dev.dts | 312 +++++++++++++--------------
2 files changed, 196 insertions(+), 212 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-apf28.dts b/arch/arm/boot/dts/imx28-apf28.dts
index 14a92fe59770..98672932e41b 100644
--- a/arch/arm/boot/dts/imx28-apf28.dts
+++ b/arch/arm/boot/dts/imx28-apf28.dts
@@ -14,67 +14,59 @@ memory@40000000 {
device_type = "memory";
reg = <0x40000000 0x08000000>;
};
+};
- apb@80000000 {
- apbh@80000000 {
- nand-controller@8000c000 {
- pinctrl-names = "default";
- pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
- status = "okay";
-
- partition@0 {
- label = "u-boot";
- reg = <0x0 0x300000>;
- };
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+};
- partition@300000 {
- label = "env";
- reg = <0x300000 0x80000>;
- };
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+ status = "okay";
- partition@380000 {
- label = "env2";
- reg = <0x380000 0x80000>;
- };
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x300000>;
+ };
- partition@400000 {
- label = "dtb";
- reg = <0x400000 0x80000>;
- };
+ partition@300000 {
+ label = "env";
+ reg = <0x300000 0x80000>;
+ };
- partition@480000 {
- label = "splash";
- reg = <0x480000 0x80000>;
- };
+ partition@380000 {
+ label = "env2";
+ reg = <0x380000 0x80000>;
+ };
- partition@500000 {
- label = "kernel";
- reg = <0x500000 0x800000>;
- };
+ partition@400000 {
+ label = "dtb";
+ reg = <0x400000 0x80000>;
+ };
- partition@d00000 {
- label = "rootfs";
- reg = <0xd00000 0xf300000>;
- };
- };
- };
+ partition@480000 {
+ label = "splash";
+ reg = <0x480000 0x80000>;
+ };
- apbx@80040000 {
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
- };
+ partition@500000 {
+ label = "kernel";
+ reg = <0x500000 0x800000>;
};
- ahb@80080000 {
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
- status = "okay";
- };
+ partition@d00000 {
+ label = "rootfs";
+ reg = <0xd00000 0xf300000>;
};
};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-apf28dev.dts b/arch/arm/boot/dts/imx28-apf28dev.dts
index 1b253b47006c..4704b6141836 100644
--- a/arch/arm/boot/dts/imx28-apf28dev.dts
+++ b/arch/arm/boot/dts/imx28-apf28dev.dts
@@ -10,166 +10,6 @@ / {
model = "Armadeus Systems APF28Dev docking/development board";
compatible = "armadeus,imx28-apf28dev", "armadeus,imx28-apf28", "fsl,imx28";
- apb@80000000 {
- apbh@80000000 {
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_4bit_pins_a
- &mmc0_cd_cfg &mmc0_sck_cfg>;
- bus-width = <4>;
- status = "okay";
- };
-
- ssp2: spi@80014000 {
- compatible = "fsl,imx28-spi";
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- status = "okay";
- };
-
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_apf28dev>;
-
- hog_pins_apf28dev: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D16__GPIO_1_16
- MX28_PAD_LCD_D17__GPIO_1_17
- MX28_PAD_LCD_D18__GPIO_1_18
- MX28_PAD_LCD_D19__GPIO_1_19
- MX28_PAD_LCD_D20__GPIO_1_20
- MX28_PAD_LCD_D21__GPIO_1_21
- MX28_PAD_LCD_D22__GPIO_1_22
- MX28_PAD_GPMI_CE1N__GPIO_0_17
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_apf28dev: lcdif-apf28dev@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- usb0_otg_apf28dev: otg-apf28dev@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D23__GPIO_1_23
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
-
- lcdif@80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_16bit_pins_a
- &lcdif_pins_apf28dev>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <16>;
- bus-width = <16>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <33000033>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <96>;
- hfront-porch = <96>;
- vback-porch = <20>;
- vfront-porch = <21>;
- hsync-len = <64>;
- vsync-len = <4>;
- hsync-active = <1>;
- vsync-active = <1>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
- };
- };
- };
-
- can0: can@80032000 {
- pinctrl-names = "default";
- pinctrl-0 = <&can0_pins_a>;
- xceiver-supply = <®_can0_vcc>;
- status = "okay";
- };
- };
-
- apbx@80040000 {
- lradc@80050000 {
- fsl,lradc-touchscreen-wires = <4>;
- status = "okay";
- };
-
- i2c0: i2c@80058000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
- };
-
- pwm: pwm@80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm3_pins_a &pwm4_pins_a>;
- status = "okay";
- };
-
- auart0: serial@8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_pins_a>;
- uart-has-rtscts;
- status = "okay";
- };
-
- usbphy0: usbphy@8007c000 {
- status = "okay";
- };
-
- usbphy1: usbphy@8007e000 {
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb0: usb@80080000 {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_otg_apf28dev
- &usb0_id_pins_b>;
- vbus-supply = <®_usb0_vbus>;
- status = "okay";
- };
-
- usb1: usb@80090000 {
- status = "okay";
- };
-
- mac1: ethernet@800f4000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac1_pins_a>;
- phy-reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
- status = "okay";
- };
- };
-
regulators {
compatible = "simple-bus";
#address-cells = <1>;
@@ -223,3 +63,155 @@ user-button {
};
};
};
+
+&auart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_pins_a>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&can0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can0_pins_a>;
+ xceiver-supply = <®_can0_vcc>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_16bit_pins_a
+ &lcdif_pins_apf28dev>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <16>;
+ bus-width = <16>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <33000033>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <96>;
+ hfront-porch = <96>;
+ vback-porch = <20>;
+ vfront-porch = <21>;
+ hsync-len = <64>;
+ vsync-len = <4>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&lradc {
+ fsl,lradc-touchscreen-wires = <4>;
+ status = "okay";
+};
+
+&mac1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ phy-reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_apf28dev>;
+
+ hog_pins_apf28dev: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D16__GPIO_1_16
+ MX28_PAD_LCD_D17__GPIO_1_17
+ MX28_PAD_LCD_D18__GPIO_1_18
+ MX28_PAD_LCD_D19__GPIO_1_19
+ MX28_PAD_LCD_D20__GPIO_1_20
+ MX28_PAD_LCD_D21__GPIO_1_21
+ MX28_PAD_LCD_D22__GPIO_1_22
+ MX28_PAD_GPMI_CE1N__GPIO_0_17
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_apf28dev: lcdif-apf28dev@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ usb0_otg_apf28dev: otg-apf28dev@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D23__GPIO_1_23
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_pins_a &pwm4_pins_a>;
+ status = "okay";
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&ssp2 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+};
+
+&usb0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_otg_apf28dev
+ &usb0_id_pins_b>;
+ vbus-supply = <®_usb0_vbus>;
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
+&usbphy0 {
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH V2 2/9] ARM: dts: imx28-m28/sps1: Convert to use label references
2023-03-07 18:39 [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files Stefan Wahren
2023-03-07 18:39 ` [PATCH V2 1/9] ARM: dts: imx28-apf28: Convert to use label references Stefan Wahren
@ 2023-03-07 18:40 ` Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 3/9] ARM: dts: imx28-apx4devkit: " Stefan Wahren
` (7 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Stefan Wahren @ 2023-03-07 18:40 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: linux-imx, devicetree, linux-arm-kernel, Stefan Wahren,
Marek Vasut, Wolfgang Grandegger
These board files still use node name and unit address to
reference parts from the imx28.dtsi . This causes a lot of
redundancy. So use label references in orer to make it
easier to maintain.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Grandegger <wg@aries-embedded.de>
---
arch/arm/boot/dts/imx28-m28.dtsi | 44 ++-
arch/arm/boot/dts/imx28-m28cu3.dts | 354 ++++++++++++------------
arch/arm/boot/dts/imx28-m28evk.dts | 420 ++++++++++++++---------------
arch/arm/boot/dts/imx28-sps1.dts | 201 +++++++-------
4 files changed, 494 insertions(+), 525 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-m28.dtsi b/arch/arm/boot/dts/imx28-m28.dtsi
index 2bdb4c093545..c08b14ad7cd5 100644
--- a/arch/arm/boot/dts/imx28-m28.dtsi
+++ b/arch/arm/boot/dts/imx28-m28.dtsi
@@ -14,31 +14,6 @@ memory@40000000 {
reg = <0x40000000 0x08000000>;
};
- apb@80000000 {
- apbh@80000000 {
- nand-controller@8000c000 {
- #address-cells = <1>;
- #size-cells = <1>;
- pinctrl-names = "default";
- pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
- status = "okay";
- };
- };
-
- apbx@80040000 {
- i2c0: i2c@80058000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- rtc: rtc@68 {
- compatible = "st,m41t62";
- reg = <0x68>;
- };
- };
- };
- };
-
regulators {
compatible = "simple-bus";
#address-cells = <1>;
@@ -54,3 +29,22 @@ reg_3p3v: regulator@0 {
};
};
};
+
+&gpmi {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ rtc: rtc@68 {
+ compatible = "st,m41t62";
+ reg = <0x68>;
+ };
+};
diff --git a/arch/arm/boot/dts/imx28-m28cu3.dts b/arch/arm/boot/dts/imx28-m28cu3.dts
index 865ac3d573c7..6b01de9efd02 100644
--- a/arch/arm/boot/dts/imx28-m28cu3.dts
+++ b/arch/arm/boot/dts/imx28-m28cu3.dts
@@ -15,187 +15,6 @@ memory@40000000 {
reg = <0x40000000 0x08000000>;
};
- apb@80000000 {
- apbh@80000000 {
- nand-controller@8000c000 {
- #address-cells = <1>;
- #size-cells = <1>;
- pinctrl-names = "default";
- pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
- status = "okay";
-
- partition@0 {
- label = "gpmi-nfc-0-boot";
- reg = <0x00000000 0x01400000>;
- read-only;
- };
-
- partition@1 {
- label = "gpmi-nfc-general-use";
- reg = <0x01400000 0x0ec00000>;
- };
- };
-
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_4bit_pins_a
- &mmc0_cd_cfg
- &mmc0_sck_cfg>;
- bus-width = <4>;
- vmmc-supply = <®_vddio_sd0>;
- status = "okay";
- };
-
- ssp2: spi@80014000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_4bit_pins_a
- &mmc2_cd_cfg
- &mmc2_sck_cfg_a>;
- bus-width = <4>;
- vmmc-supply = <®_vddio_sd1>;
- status = "okay";
- };
-
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP2_SS0__GPIO_2_19
- MX28_PAD_PWM4__GPIO_3_29
- MX28_PAD_AUART2_RX__GPIO_3_8
- MX28_PAD_ENET0_RX_CLK__GPIO_4_13
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_m28: lcdif-m28@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_VSYNC__LCD_VSYNC
- MX28_PAD_LCD_HSYNC__LCD_HSYNC
- MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
- MX28_PAD_LCD_RESET__LCD_RESET
- MX28_PAD_LCD_CS__LCD_ENABLE
- MX28_PAD_AUART1_TX__GPIO_3_5
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- led_pins_gpio: leds-m28@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP3_MISO__GPIO_2_26
- MX28_PAD_SSP3_SCK__GPIO_2_24
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
-
- ocotp@8002c000 {
- status = "okay";
- };
-
- lcdif@80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_24bit_pins_a
- &lcdif_pins_m28>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <6410256>;
- hactive = <320>;
- vactive = <240>;
- hback-porch = <38>;
- hfront-porch = <20>;
- vback-porch = <15>;
- vfront-porch = <5>;
- hsync-len = <30>;
- vsync-len = <3>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
- };
- };
-
- apbx@80040000 {
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_b>;
- status = "okay";
- };
-
- usbphy1: usbphy@8007e000 {
- status = "okay";
- };
-
- auart0: serial@8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_2pins_a>;
- status = "okay";
- };
-
- auart3: serial@80070000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart3_2pins_b>;
- status = "okay";
- };
-
- pwm: pwm@80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm3_pins_a>;
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb1: usb@80090000 {
- vbus-supply = <®_usb1_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_pins_a>;
- disable-over-current;
- status = "okay";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <100>;
- status = "okay";
- };
-
- mac1: ethernet@800f4000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac1_pins_a>;
- status = "okay";
- };
- };
-
backlight {
compatible = "pwm-backlight";
pwms = <&pwm 3 5000000>;
@@ -264,3 +83,176 @@ reg_usb1_vbus: regulator@3 {
};
};
};
+
+&auart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_2pins_a>;
+ status = "okay";
+};
+
+&auart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart3_2pins_b>;
+ status = "okay";
+};
+
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_b>;
+ status = "okay";
+};
+
+&gpmi {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+ status = "okay";
+
+ partition@0 {
+ label = "gpmi-nfc-0-boot";
+ reg = <0x00000000 0x01400000>;
+ read-only;
+ };
+
+ partition@1 {
+ label = "gpmi-nfc-general-use";
+ reg = <0x01400000 0x0ec00000>;
+ };
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a
+ &lcdif_pins_m28>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <6410256>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vfront-porch = <5>;
+ hsync-len = <30>;
+ vsync-len = <3>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <100>;
+ status = "okay";
+};
+
+&mac1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ status = "okay";
+};
+
+&ocotp {
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SS0__GPIO_2_19
+ MX28_PAD_PWM4__GPIO_3_29
+ MX28_PAD_AUART2_RX__GPIO_3_8
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_m28: lcdif-m28@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_VSYNC__LCD_VSYNC
+ MX28_PAD_LCD_HSYNC__LCD_HSYNC
+ MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+ MX28_PAD_LCD_RESET__LCD_RESET
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ MX28_PAD_AUART1_TX__GPIO_3_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins_gpio: leds-m28@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP3_MISO__GPIO_2_26
+ MX28_PAD_SSP3_SCK__GPIO_2_24
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_pins_a>;
+ status = "okay";
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a
+ &mmc0_cd_cfg
+ &mmc0_sck_cfg>;
+ bus-width = <4>;
+ vmmc-supply = <®_vddio_sd0>;
+ status = "okay";
+};
+
+&ssp2 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_4bit_pins_a
+ &mmc2_cd_cfg
+ &mmc2_sck_cfg_a>;
+ bus-width = <4>;
+ vmmc-supply = <®_vddio_sd1>;
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_pins_a>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts
index 13acdc7916b9..e350d57a4cec 100644
--- a/arch/arm/boot/dts/imx28-m28evk.dts
+++ b/arch/arm/boot/dts/imx28-m28evk.dts
@@ -11,220 +11,6 @@ / {
model = "Aries/DENX M28EVK";
compatible = "aries,m28evk", "denx,m28evk", "fsl,imx28";
- apb@80000000 {
- apbh@80000000 {
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_8bit_pins_a
- &mmc0_cd_cfg
- &mmc0_sck_cfg>;
- bus-width = <8>;
- wp-gpios = <&gpio3 10 0>;
- vmmc-supply = <®_vddio_sd0>;
- status = "okay";
- };
-
- ssp2: spi@80014000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx28-spi";
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- status = "okay";
-
- flash: flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "m25p80", "jedec,spi-nor";
- spi-max-frequency = <40000000>;
- reg = <0>;
- };
- };
-
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_PWM3__GPIO_3_28
- MX28_PAD_AUART2_CTS__GPIO_3_10
- MX28_PAD_AUART2_RTS__GPIO_3_11
- MX28_PAD_AUART3_RX__GPIO_3_12
- MX28_PAD_AUART3_TX__GPIO_3_13
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_m28: lcdif-m28@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
- MX28_PAD_LCD_ENABLE__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
-
- lcdif@80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_24bit_pins_a
- &lcdif_pins_m28>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <16>;
- bus-width = <18>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <33260000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <0>;
- hfront-porch = <256>;
- vback-porch = <0>;
- vfront-porch = <45>;
- hsync-len = <1>;
- vsync-len = <1>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
- };
-
- can0: can@80032000 {
- pinctrl-names = "default";
- pinctrl-0 = <&can0_pins_a>;
- status = "okay";
- };
-
- can1: can@80034000 {
- pinctrl-names = "default";
- pinctrl-0 = <&can1_pins_a>;
- status = "okay";
- };
- };
-
- apbx@80040000 {
- saif0: saif@80042000 {
- pinctrl-names = "default";
- pinctrl-0 = <&saif0_pins_a>;
- status = "okay";
- };
-
- saif1: saif@80046000 {
- pinctrl-names = "default";
- pinctrl-0 = <&saif1_pins_a>;
- fsl,saif-master = <&saif0>;
- status = "okay";
- };
-
- i2c0: i2c@80058000 {
- sgtl5000: codec@a {
- compatible = "fsl,sgtl5000";
- reg = <0x0a>;
- #sound-dai-cells = <0>;
- VDDA-supply = <®_3p3v>;
- VDDIO-supply = <®_3p3v>;
- clocks = <&saif0>;
- };
-
- eeprom: eeprom@51 {
- compatible = "atmel,24c128";
- reg = <0x51>;
- pagesize = <32>;
- };
- };
-
- lradc@80050000 {
- status = "okay";
- fsl,lradc-touchscreen-wires = <4>;
- };
-
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
-
- usbphy0: usbphy@8007c000 {
- status = "okay";
- };
-
- usbphy1: usbphy@8007e000 {
- status = "okay";
- };
-
- auart0: serial@8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_pins_a>;
- status = "okay";
- };
-
- auart1: serial@8006c000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart1_pins_a>;
- status = "okay";
- };
-
- auart2: serial@8006e000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart2_2pins_b>;
- status = "okay";
- };
-
- pwm: pwm@80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm4_pins_a>;
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb0: usb@80080000 {
- vbus-supply = <®_usb0_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_pins_a>;
- status = "okay";
- };
-
- usb1: usb@80090000 {
- vbus-supply = <®_usb1_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_pins_a>;
- status = "okay";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- clocks = <&clks 57>, <&clks 57>;
- clock-names = "ipg", "ahb";
- status = "okay";
- };
-
- mac1: ethernet@800f4000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac1_pins_a>;
- status = "okay";
- };
- };
-
backlight {
compatible = "pwm-backlight";
pwms = <&pwm 4 5000000>;
@@ -269,3 +55,209 @@ sound {
audio-codec = <&sgtl5000>;
};
};
+
+&auart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_pins_a>;
+ status = "okay";
+};
+
+&auart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart1_pins_a>;
+ status = "okay";
+};
+
+&auart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart2_2pins_b>;
+ status = "okay";
+};
+
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+};
+
+&i2c0 {
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ #sound-dai-cells = <0>;
+ VDDA-supply = <®_3p3v>;
+ VDDIO-supply = <®_3p3v>;
+ clocks = <&saif0>;
+ };
+
+ eeprom: eeprom@51 {
+ compatible = "atmel,24c128";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a
+ &lcdif_pins_m28>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <16>;
+ bus-width = <18>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <33260000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <0>;
+ hfront-porch = <256>;
+ vback-porch = <0>;
+ vfront-porch = <45>;
+ hsync-len = <1>;
+ vsync-len = <1>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&lradc {
+ status = "okay";
+ fsl,lradc-touchscreen-wires = <4>;
+};
+
+&can0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can0_pins_a>;
+ status = "okay";
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can1_pins_a>;
+ status = "okay";
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ clocks = <&clks 57>, <&clks 57>;
+ clock-names = "ipg", "ahb";
+ status = "okay";
+};
+
+&mac1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_AUART2_CTS__GPIO_3_10
+ MX28_PAD_AUART2_RTS__GPIO_3_11
+ MX28_PAD_AUART3_RX__GPIO_3_12
+ MX28_PAD_AUART3_TX__GPIO_3_13
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_m28: lcdif-m28@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+ MX28_PAD_LCD_ENABLE__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm4_pins_a>;
+ status = "okay";
+};
+
+&saif0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif0_pins_a>;
+ status = "okay";
+};
+
+&saif1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif1_pins_a>;
+ fsl,saif-master = <&saif0>;
+ status = "okay";
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg
+ &mmc0_sck_cfg>;
+ bus-width = <8>;
+ wp-gpios = <&gpio3 10 0>;
+ vmmc-supply = <®_vddio_sd0>;
+ status = "okay";
+};
+
+&ssp2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+
+ flash: flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p80", "jedec,spi-nor";
+ spi-max-frequency = <40000000>;
+ reg = <0>;
+ };
+};
+
+&usb0 {
+ vbus-supply = <®_usb0_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_pins_a>;
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_pins_a>;
+ status = "okay";
+};
+
+&usbphy0 {
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-sps1.dts b/arch/arm/boot/dts/imx28-sps1.dts
index 90928db0df70..5d74a68c56ff 100644
--- a/arch/arm/boot/dts/imx28-sps1.dts
+++ b/arch/arm/boot/dts/imx28-sps1.dts
@@ -15,111 +15,6 @@ memory@40000000 {
reg = <0x40000000 0x08000000>;
};
- apb@80000000 {
- apbh@80000000 {
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog-gpios@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_D00__GPIO_0_0
- MX28_PAD_GPMI_D03__GPIO_0_3
- MX28_PAD_GPMI_D06__GPIO_0_6
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- };
-
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_4bit_pins_a>;
- bus-width = <4>;
- status = "okay";
- };
-
- ssp2: spi@80014000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx28-spi";
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- status = "okay";
-
- flash: flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "everspin,mr25h256", "mr25h256";
- spi-max-frequency = <40000000>;
- reg = <0>;
- };
- };
- };
-
- apbx@80040000 {
- i2c0: i2c@80058000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- rtc: rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-
- eeprom: eeprom@52 {
- compatible = "atmel,24c64";
- reg = <0x52>;
- pagesize = <32>;
- };
- };
-
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
-
- usbphy0: usbphy@8007c000 {
- status = "okay";
- };
-
- auart0: serial@8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_pins_a>;
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb0: usb@80080000 {
- vbus-supply = <®_usb0_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_pins_b>;
- status = "okay";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- status = "okay";
- };
-
- mac1: ethernet@800f4000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac1_pins_a>;
- status = "okay";
- };
- };
-
regulators {
compatible = "simple-bus";
#address-cells = <1>;
@@ -164,3 +59,99 @@ led@3 {
};
};
+
+&auart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_pins_a>;
+ status = "okay";
+};
+
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ rtc: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ eeprom: eeprom@52 {
+ compatible = "atmel,24c64";
+ reg = <0x52>;
+ pagesize = <32>;
+ };
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ status = "okay";
+};
+
+&mac1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog-gpios@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D00__GPIO_0_0
+ MX28_PAD_GPMI_D03__GPIO_0_3
+ MX28_PAD_GPMI_D06__GPIO_0_6
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&ssp2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+
+ flash: flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "everspin,mr25h256", "mr25h256";
+ spi-max-frequency = <40000000>;
+ reg = <0>;
+ };
+};
+
+&usb0 {
+ vbus-supply = <®_usb0_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_pins_b>;
+ status = "okay";
+};
+
+&usbphy0 {
+ status = "okay";
+};
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH V2 3/9] ARM: dts: imx28-apx4devkit: Convert to use label references
2023-03-07 18:39 [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files Stefan Wahren
2023-03-07 18:39 ` [PATCH V2 1/9] ARM: dts: imx28-apf28: Convert to use label references Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 2/9] ARM: dts: imx28-m28/sps1: " Stefan Wahren
@ 2023-03-07 18:40 ` Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 4/9] ARM: dts: imx28-cfa10036: " Stefan Wahren
` (6 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Stefan Wahren @ 2023-03-07 18:40 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: linux-imx, devicetree, linux-arm-kernel, Stefan Wahren, Aapo Vienamo
This board file still use node name and unit address to
reference parts from the imx28.dtsi . This causes a lot of
redundancy. So use label references in orer to make it
easier to maintain.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Aapo Vienamo <aapo.vienamo@iki.fi>
---
arch/arm/boot/dts/imx28-apx4devkit.dts | 380 ++++++++++++-------------
1 file changed, 186 insertions(+), 194 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts
index b86be320496b..f9bf40d96568 100644
--- a/arch/arm/boot/dts/imx28-apx4devkit.dts
+++ b/arch/arm/boot/dts/imx28-apx4devkit.dts
@@ -11,200 +11,6 @@ memory@40000000 {
reg = <0x40000000 0x04000000>;
};
- apb@80000000 {
- apbh@80000000 {
- nand-controller@8000c000 {
- pinctrl-names = "default";
- pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
- status = "okay";
- };
-
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>;
- bus-width = <4>;
- status = "okay";
- };
-
- ssp2: spi@80014000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_4bit_pins_apx4 &mmc2_sck_cfg_apx4>;
- bus-width = <4>;
- status = "okay";
- };
-
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_CE1N__GPIO_0_17
- MX28_PAD_GPMI_RDY1__GPIO_0_21
- MX28_PAD_SSP2_MISO__GPIO_2_18
- MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */
- MX28_PAD_PWM3__GPIO_3_28
- MX28_PAD_LCD_RESET__GPIO_3_30
- MX28_PAD_JTAG_RTCK__GPIO_4_20
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_apx4: lcdif-apx4@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP0_DATA4__SSP2_D0
- MX28_PAD_SSP0_DATA5__SSP2_D3
- MX28_PAD_SSP0_DATA6__SSP2_CMD
- MX28_PAD_SSP0_DATA7__SSP2_SCK
- MX28_PAD_SSP2_SS1__SSP2_D1
- MX28_PAD_SSP2_SS2__SSP2_D2
- >;
- fsl,drive-strength = <MXS_DRIVE_8mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP0_DATA7__SSP2_SCK
- >;
- fsl,drive-strength = <MXS_DRIVE_12mA>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
-
- lcdif@80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_24bit_pins_a
- &lcdif_pins_apx4>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <30000000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <88>;
- hfront-porch = <40>;
- vback-porch = <32>;
- vfront-porch = <13>;
- hsync-len = <48>;
- vsync-len = <3>;
- hsync-active = <1>;
- vsync-active = <1>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
- };
- };
- };
- };
-
- apbx@80040000 {
- saif0: saif@80042000 {
- pinctrl-names = "default";
- pinctrl-0 = <&saif0_pins_a>;
- status = "okay";
- };
-
- saif1: saif@80046000 {
- pinctrl-names = "default";
- pinctrl-0 = <&saif1_pins_a>;
- fsl,saif-master = <&saif0>;
- status = "okay";
- };
-
- i2c0: i2c@80058000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- sgtl5000: codec@a {
- compatible = "fsl,sgtl5000";
- reg = <0x0a>;
- #sound-dai-cells = <0>;
- VDDA-supply = <®_3p3v>;
- VDDIO-supply = <®_3p3v>;
- clocks = <&saif0>;
- };
-
- pcf8563: rtc@51 {
- compatible = "phg,pcf8563";
- reg = <0x51>;
- };
- };
-
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
-
- auart0: serial@8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_pins_a>;
- status = "okay";
- };
-
- auart1: serial@8006c000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart1_2pins_a>;
- status = "okay";
- };
-
- auart2: serial@8006e000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart2_2pins_a>;
- status = "okay";
- };
-
- usbphy1: usbphy@8007e000 {
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_pins_a>;
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb1: usb@80090000 {
- status = "okay";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- status = "okay";
- };
- };
-
regulators {
compatible = "simple-bus";
#address-cells = <1>;
@@ -238,3 +44,189 @@ user {
};
};
};
+
+&auart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_pins_a>;
+ status = "okay";
+};
+
+&auart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart1_2pins_a>;
+ status = "okay";
+};
+
+&auart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart2_2pins_a>;
+ status = "okay";
+};
+
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+ status = "okay";
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a
+ &lcdif_pins_apx4>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <30000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hfront-porch = <40>;
+ vback-porch = <32>;
+ vfront-porch = <13>;
+ hsync-len = <48>;
+ vsync-len = <3>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ #sound-dai-cells = <0>;
+ VDDA-supply = <®_3p3v>;
+ VDDIO-supply = <®_3p3v>;
+ clocks = <&saif0>;
+ };
+
+ pcf8563: rtc@51 {
+ compatible = "phg,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_CE1N__GPIO_0_17
+ MX28_PAD_GPMI_RDY1__GPIO_0_21
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ MX28_PAD_JTAG_RTCK__GPIO_4_20
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_apx4: lcdif-apx4@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP0_DATA4__SSP2_D0
+ MX28_PAD_SSP0_DATA5__SSP2_D3
+ MX28_PAD_SSP0_DATA6__SSP2_CMD
+ MX28_PAD_SSP0_DATA7__SSP2_SCK
+ MX28_PAD_SSP2_SS1__SSP2_D1
+ MX28_PAD_SSP2_SS2__SSP2_D2
+ >;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP0_DATA7__SSP2_SCK
+ >;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&saif0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif0_pins_a>;
+ status = "okay";
+};
+
+&saif1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif1_pins_a>;
+ fsl,saif-master = <&saif0>;
+ status = "okay";
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&ssp2 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_4bit_pins_apx4 &mmc2_sck_cfg_apx4>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
+&usbphy1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_pins_a>;
+ status = "okay";
+};
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH V2 4/9] ARM: dts: imx28-cfa10036: Convert to use label references
2023-03-07 18:39 [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files Stefan Wahren
` (2 preceding siblings ...)
2023-03-07 18:40 ` [PATCH V2 3/9] ARM: dts: imx28-apx4devkit: " Stefan Wahren
@ 2023-03-07 18:40 ` Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 5/9] ARM: dts: imx28-duckbill: " Stefan Wahren
` (5 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Stefan Wahren @ 2023-03-07 18:40 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: linux-imx, devicetree, linux-arm-kernel, Stefan Wahren,
Brian Lilly, Michal Vokáč
These Crystal fontz board files still use node name and unit
address to reference parts from the imx28.dtsi . This causes
a lot of redundancy. So use label references in order to make
it easier to maintain.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Brian Lilly <brian@crystalfontz.com>
Cc: Michal Vokáč <michal.vokac@ysoft.com>
---
arch/arm/boot/dts/imx28-cfa10036.dts | 193 ++++++------
arch/arm/boot/dts/imx28-cfa10049.dts | 454 +++++++++++++--------------
arch/arm/boot/dts/imx28-cfa10055.dts | 224 +++++++------
arch/arm/boot/dts/imx28-cfa10056.dts | 146 +++++----
arch/arm/boot/dts/imx28-cfa10057.dts | 252 +++++++--------
arch/arm/boot/dts/imx28-cfa10058.dts | 186 ++++++-----
6 files changed, 703 insertions(+), 752 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts
index 85aa1cc3ff66..d004b1cbb4ae 100644
--- a/arch/arm/boot/dts/imx28-cfa10036.dts
+++ b/arch/arm/boot/dts/imx28-cfa10036.dts
@@ -16,107 +16,6 @@ memory@40000000 {
reg = <0x40000000 0x08000000>;
};
- apb@80000000 {
- apbh@80000000 {
- pinctrl@80018000 {
- ssd1306_cfa10036: ssd1306-10036@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP0_DATA7__GPIO_2_7
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- led_pins_cfa10036: leds-10036@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_AUART1_RX__GPIO_3_4
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- usb0_otg_cfa10036: otg-10036@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_RDY0__USB0_ID
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mmc_pwr_cfa10036: mmc_pwr_cfa10036@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- 0x31c3 /*
- MX28_PAD_PWM3__GPIO_3_28 */
- >;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
- };
-
- };
-
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_4bit_pins_a
- &mmc0_cd_cfg &mmc0_sck_cfg>;
- vmmc-supply = <®_vddio_sd0>;
- bus-width = <4>;
- status = "okay";
- };
- };
-
- apbx@80040000 {
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_b>;
- status = "okay";
- };
-
- i2c0: i2c@80058000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_b>;
- clock-frequency = <400000>;
- status = "okay";
-
- ssd1306: oled@3c {
- compatible = "solomon,ssd1306fb-i2c";
- pinctrl-names = "default";
- pinctrl-0 = <&ssd1306_cfa10036>;
- reg = <0x3c>;
- reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
- solomon,height = <32>;
- solomon,width = <128>;
- solomon,page-offset = <0>;
- solomon,com-lrremap;
- solomon,com-invdir;
- solomon,com-offset = <32>;
- };
- };
-
- usbphy0: usbphy@8007c000 {
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb0: usb@80080000 {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_otg_cfa10036>;
- dr_mode = "peripheral";
- phy_type = "utmi";
- status = "okay";
- };
- };
-
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -138,3 +37,95 @@ reg_vddio_sd0: vddio-sd0 {
gpio = <&gpio3 28 0>;
};
};
+
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_b>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_b>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ ssd1306: oled@3c {
+ compatible = "solomon,ssd1306fb-i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ssd1306_cfa10036>;
+ reg = <0x3c>;
+ reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+ solomon,height = <32>;
+ solomon,width = <128>;
+ solomon,page-offset = <0>;
+ solomon,com-lrremap;
+ solomon,com-invdir;
+ solomon,com-offset = <32>;
+ };
+};
+
+&pinctrl {
+ ssd1306_cfa10036: ssd1306-10036@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP0_DATA7__GPIO_2_7
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins_cfa10036: leds-10036@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART1_RX__GPIO_3_4
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ usb0_otg_cfa10036: otg-10036@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_RDY0__USB0_ID
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mmc_pwr_cfa10036: mmc_pwr_cfa10036@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x31c3 /*
+ MX28_PAD_PWM3__GPIO_3_28 */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ vmmc-supply = <®_vddio_sd0>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&usb0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_otg_cfa10036>;
+ dr_mode = "peripheral";
+ phy_type = "utmi";
+ status = "okay";
+};
+
+&usbphy0 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 9ef0d567ea48..94d6614c1983 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -78,226 +78,6 @@ pca9555: pca9555@20 {
};
};
- apb@80000000 {
- apbh@80000000 {
- pinctrl@80018000 {
- usb_pins_cfa10049: usb-10049@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_D07__GPIO_0_7
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- i2cmux_pins_cfa10049: i2cmux-10049@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D22__GPIO_1_22
- MX28_PAD_LCD_D23__GPIO_1_23
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_pins_cfa10049: mac0-10049@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP2_SS2__GPIO_2_21
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- pca_pins_cfa10049: pca-10049@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP2_SS0__GPIO_2_19
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- rotary_pins_cfa10049: rotary-10049@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_I2C0_SCL__GPIO_3_24
- MX28_PAD_I2C0_SDA__GPIO_3_25
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- rotary_btn_pins_cfa10049: rotary-btn-10049@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SAIF1_SDATA0__GPIO_3_26
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- spi2_pins_cfa10049: spi2-cfa10049@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP2_SCK__GPIO_2_16
- MX28_PAD_SSP2_MOSI__GPIO_2_17
- MX28_PAD_SSP2_MISO__GPIO_2_18
- MX28_PAD_AUART1_TX__GPIO_3_5
- >;
- fsl,drive-strength = <MXS_DRIVE_8mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- spi3_pins_cfa10049: spi3-cfa10049@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_RDN__GPIO_0_24
- MX28_PAD_GPMI_RESETN__GPIO_0_28
- MX28_PAD_GPMI_CE1N__GPIO_0_17
- MX28_PAD_GPMI_ALE__GPIO_0_26
- MX28_PAD_GPMI_CLE__GPIO_0_27
- >;
- fsl,drive-strength = <MXS_DRIVE_8mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- lcdif_18bit_pins_cfa10049: lcdif-18bit@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D00__LCD_D0
- MX28_PAD_LCD_D01__LCD_D1
- MX28_PAD_LCD_D02__LCD_D2
- MX28_PAD_LCD_D03__LCD_D3
- MX28_PAD_LCD_D04__LCD_D4
- MX28_PAD_LCD_D05__LCD_D5
- MX28_PAD_LCD_D06__LCD_D6
- MX28_PAD_LCD_D07__LCD_D7
- MX28_PAD_LCD_D08__LCD_D8
- MX28_PAD_LCD_D09__LCD_D9
- MX28_PAD_LCD_D10__LCD_D10
- MX28_PAD_LCD_D11__LCD_D11
- MX28_PAD_LCD_D12__LCD_D12
- MX28_PAD_LCD_D13__LCD_D13
- MX28_PAD_LCD_D14__LCD_D14
- MX28_PAD_LCD_D15__LCD_D15
- MX28_PAD_LCD_D16__LCD_D16
- MX28_PAD_LCD_D17__LCD_D17
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_cfa10049: lcdif-evk@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RESET__GPIO_3_30
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- w1_gpio_pins: w1-gpio@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D21__GPIO_1_21
- >;
- fsl,drive-strength = <MXS_DRIVE_8mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>; /* 0 will enable the keeper */
- };
- };
-
- lcdif@80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_18bit_pins_cfa10049
- &lcdif_pins_cfa10049
- &lcdif_pins_cfa10049_pullup>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <18>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <9216000>;
- hactive = <320>;
- vactive = <480>;
- hback-porch = <2>;
- hfront-porch = <2>;
- vback-porch = <2>;
- vfront-porch = <2>;
- hsync-len = <15>;
- vsync-len = <15>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
- };
- };
-
- apbx@80040000 {
- pwm: pwm@80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm3_pins_b>;
- status = "okay";
- };
-
- i2c1: i2c@8005a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
- };
-
- usbphy1: usbphy@8007e000 {
- status = "okay";
- };
-
- lradc@80050000 {
- status = "okay";
- fsl,lradc-touchscreen-wires = <4>;
- };
- };
- };
-
- ahb@80080000 {
- usb1: usb@80090000 {
- vbus-supply = <®_usb1_vbus>;
- pinctrl-0 = <&usb1_pins_a>;
- pinctrl-names = "default";
- status = "okay";
- };
- };
-
regulators {
compatible = "simple-bus";
#address-cells = <1>;
@@ -315,18 +95,6 @@ reg_usb1_vbus: regulator@0 {
};
};
- ahb@80080000 {
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a
- &mac0_pins_cfa10049>;
- phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <100>;
- status = "okay";
- };
- };
-
spi-2 {
compatible = "spi-gpio";
pinctrl-names = "default";
@@ -426,3 +194,225 @@ onewire {
gpios = <&gpio1 21 0>;
};
};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_18bit_pins_cfa10049
+ &lcdif_pins_cfa10049
+ &lcdif_pins_cfa10049_pullup>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <18>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <9216000>;
+ hactive = <320>;
+ vactive = <480>;
+ hback-porch = <2>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vfront-porch = <2>;
+ hsync-len = <15>;
+ vsync-len = <15>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&lradc {
+ fsl,lradc-touchscreen-wires = <4>;
+ status = "okay";
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a
+ &mac0_pins_cfa10049>;
+ phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <100>;
+ status = "okay";
+};
+
+&pinctrl {
+ usb_pins_cfa10049: usb-10049@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ i2cmux_pins_cfa10049: i2cmux-10049@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D22__GPIO_1_22
+ MX28_PAD_LCD_D23__GPIO_1_23
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_pins_cfa10049: mac0-10049@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SS2__GPIO_2_21
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ pca_pins_cfa10049: pca-10049@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SS0__GPIO_2_19
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ rotary_pins_cfa10049: rotary-10049@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_I2C0_SCL__GPIO_3_24
+ MX28_PAD_I2C0_SDA__GPIO_3_25
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ rotary_btn_pins_cfa10049: rotary-btn-10049@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF1_SDATA0__GPIO_3_26
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ spi2_pins_cfa10049: spi2-cfa10049@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SCK__GPIO_2_16
+ MX28_PAD_SSP2_MOSI__GPIO_2_17
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_AUART1_TX__GPIO_3_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ spi3_pins_cfa10049: spi3-cfa10049@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_RDN__GPIO_0_24
+ MX28_PAD_GPMI_RESETN__GPIO_0_28
+ MX28_PAD_GPMI_CE1N__GPIO_0_17
+ MX28_PAD_GPMI_ALE__GPIO_0_26
+ MX28_PAD_GPMI_CLE__GPIO_0_27
+ >;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ lcdif_18bit_pins_cfa10049: lcdif-18bit@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_cfa10049: lcdif-evk@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ w1_gpio_pins: w1-gpio@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D21__GPIO_1_21
+ >;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>; /* 0 will enable the keeper */
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_pins_b>;
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb1_vbus>;
+ pinctrl-0 = <&usb1_pins_a>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10055.dts b/arch/arm/boot/dts/imx28-cfa10055.dts
index fac5bbda7a93..42ba7da48beb 100644
--- a/arch/arm/boot/dts/imx28-cfa10055.dts
+++ b/arch/arm/boot/dts/imx28-cfa10055.dts
@@ -14,121 +14,6 @@ / {
model = "Crystalfontz CFA-10055 Board";
compatible = "crystalfontz,cfa10055", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
- apb@80000000 {
- apbh@80000000 {
- pinctrl@80018000 {
- spi2_pins_cfa10055: spi2-cfa10055@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP2_SCK__GPIO_2_16
- MX28_PAD_SSP2_MOSI__GPIO_2_17
- MX28_PAD_SSP2_MISO__GPIO_2_18
- MX28_PAD_AUART1_TX__GPIO_3_5
- >;
- fsl,drive-strength = <MXS_DRIVE_8mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- lcdif_18bit_pins_cfa10055: lcdif-18bit@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D00__LCD_D0
- MX28_PAD_LCD_D01__LCD_D1
- MX28_PAD_LCD_D02__LCD_D2
- MX28_PAD_LCD_D03__LCD_D3
- MX28_PAD_LCD_D04__LCD_D4
- MX28_PAD_LCD_D05__LCD_D5
- MX28_PAD_LCD_D06__LCD_D6
- MX28_PAD_LCD_D07__LCD_D7
- MX28_PAD_LCD_D08__LCD_D8
- MX28_PAD_LCD_D09__LCD_D9
- MX28_PAD_LCD_D10__LCD_D10
- MX28_PAD_LCD_D11__LCD_D11
- MX28_PAD_LCD_D12__LCD_D12
- MX28_PAD_LCD_D13__LCD_D13
- MX28_PAD_LCD_D14__LCD_D14
- MX28_PAD_LCD_D15__LCD_D15
- MX28_PAD_LCD_D16__LCD_D16
- MX28_PAD_LCD_D17__LCD_D17
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_cfa10055: lcdif-evk@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RESET__GPIO_3_30
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
- };
-
- lcdif@80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_18bit_pins_cfa10055
- &lcdif_pins_cfa10055
- &lcdif_pins_cfa10055_pullup>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <18>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <9216000>;
- hactive = <320>;
- vactive = <480>;
- hback-porch = <2>;
- hfront-porch = <2>;
- vback-porch = <2>;
- vfront-porch = <2>;
- hsync-len = <15>;
- vsync-len = <15>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
- };
- };
-
- apbx@80040000 {
- lradc@80050000 {
- fsl,lradc-touchscreen-wires = <4>;
- status = "okay";
- };
-
- pwm: pwm@80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm3_pins_b>;
- status = "okay";
- };
- };
- };
-
spi-2 {
compatible = "spi-gpio";
pinctrl-names = "default";
@@ -159,3 +44,112 @@ backlight {
default-brightness-level = <6>;
};
};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_18bit_pins_cfa10055
+ &lcdif_pins_cfa10055
+ &lcdif_pins_cfa10055_pullup>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <18>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <9216000>;
+ hactive = <320>;
+ vactive = <480>;
+ hback-porch = <2>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vfront-porch = <2>;
+ hsync-len = <15>;
+ vsync-len = <15>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&lradc {
+ fsl,lradc-touchscreen-wires = <4>;
+ status = "okay";
+};
+
+&pinctrl {
+ spi2_pins_cfa10055: spi2-cfa10055@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SCK__GPIO_2_16
+ MX28_PAD_SSP2_MOSI__GPIO_2_17
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_AUART1_TX__GPIO_3_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ lcdif_18bit_pins_cfa10055: lcdif-18bit@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_cfa10055: lcdif-evk@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_pins_b>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10056.dts b/arch/arm/boot/dts/imx28-cfa10056.dts
index c5f3337e8b39..0e15bdfd7281 100644
--- a/arch/arm/boot/dts/imx28-cfa10056.dts
+++ b/arch/arm/boot/dts/imx28-cfa10056.dts
@@ -13,81 +13,6 @@ / {
model = "Crystalfontz CFA-10056 Board";
compatible = "crystalfontz,cfa10056", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
- apb@80000000 {
- apbh@80000000 {
- pinctrl@80018000 {
- spi2_pins_cfa10056: spi2-cfa10056@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP2_SCK__GPIO_2_16
- MX28_PAD_SSP2_MOSI__GPIO_2_17
- MX28_PAD_SSP2_MISO__GPIO_2_18
- MX28_PAD_AUART1_TX__GPIO_3_5
- >;
- fsl,drive-strength = <MXS_DRIVE_8mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- lcdif_pins_cfa10056: lcdif-10056@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RESET__GPIO_3_30
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
- };
-
- lcdif@80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_24bit_pins_a
- &lcdif_pins_cfa10056
- &lcdif_pins_cfa10056_pullup >;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <32000000>;
- hactive = <480>;
- vactive = <800>;
- hback-porch = <2>;
- hfront-porch = <2>;
- vback-porch = <2>;
- vfront-porch = <2>;
- hsync-len = <5>;
- vsync-len = <5>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
- };
- };
- };
-
spi-2 {
compatible = "spi-gpio";
pinctrl-names = "default";
@@ -111,3 +36,74 @@ hx8369: hx8369@0 {
};
};
};
+
+&pinctrl {
+ spi2_pins_cfa10056: spi2-cfa10056@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SCK__GPIO_2_16
+ MX28_PAD_SSP2_MOSI__GPIO_2_17
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_AUART1_TX__GPIO_3_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ lcdif_pins_cfa10056: lcdif-10056@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a
+ &lcdif_pins_cfa10056
+ &lcdif_pins_cfa10056_pullup >;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <32000000>;
+ hactive = <480>;
+ vactive = <800>;
+ hback-porch = <2>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vfront-porch = <2>;
+ hsync-len = <5>;
+ vsync-len = <5>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts
index 2f7e479dbc74..27602c01f162 100644
--- a/arch/arm/boot/dts/imx28-cfa10057.dts
+++ b/arch/arm/boot/dts/imx28-cfa10057.dts
@@ -14,126 +14,6 @@ / {
model = "Crystalfontz CFA-10057 Board";
compatible = "crystalfontz,cfa10057", "crystalfontz,cfa10036", "fsl,imx28";
- apb@80000000 {
- apbh@80000000 {
- pinctrl@80018000 {
- usb_pins_cfa10057: usb-10057@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_D07__GPIO_0_7
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D00__LCD_D0
- MX28_PAD_LCD_D01__LCD_D1
- MX28_PAD_LCD_D02__LCD_D2
- MX28_PAD_LCD_D03__LCD_D3
- MX28_PAD_LCD_D04__LCD_D4
- MX28_PAD_LCD_D05__LCD_D5
- MX28_PAD_LCD_D06__LCD_D6
- MX28_PAD_LCD_D07__LCD_D7
- MX28_PAD_LCD_D08__LCD_D8
- MX28_PAD_LCD_D09__LCD_D9
- MX28_PAD_LCD_D10__LCD_D10
- MX28_PAD_LCD_D11__LCD_D11
- MX28_PAD_LCD_D12__LCD_D12
- MX28_PAD_LCD_D13__LCD_D13
- MX28_PAD_LCD_D14__LCD_D14
- MX28_PAD_LCD_D15__LCD_D15
- MX28_PAD_LCD_D16__LCD_D16
- MX28_PAD_LCD_D17__LCD_D17
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_cfa10057: lcdif-evk@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
-
- lcdif@80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_18bit_pins_cfa10057
- &lcdif_pins_cfa10057>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <18>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <30000000>;
- hactive = <480>;
- vactive = <800>;
- hfront-porch = <12>;
- hback-porch = <2>;
- vfront-porch = <5>;
- vback-porch = <3>;
- hsync-len = <2>;
- vsync-len = <2>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
- };
- };
-
- apbx@80040000 {
- lradc@80050000 {
- fsl,lradc-touchscreen-wires = <4>;
- status = "okay";
- };
-
- pwm: pwm@80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm4_pins_a>;
- status = "okay";
- };
-
- i2c1: i2c@8005a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
- };
-
- usbphy1: usbphy@8007e000 {
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb1: usb@80090000 {
- vbus-supply = <®_usb1_vbus>;
- pinctrl-0 = <&usb1_pins_a>;
- pinctrl-names = "default";
- status = "okay";
- };
- };
-
regulators {
compatible = "simple-bus";
#address-cells = <1>;
@@ -151,17 +31,6 @@ reg_usb1_vbus: regulator@0 {
};
};
- ahb@80080000 {
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <100>;
- status = "okay";
- };
- };
-
backlight {
compatible = "pwm-backlight";
pwms = <&pwm 4 5000000>;
@@ -169,3 +38,124 @@ backlight {
default-brightness-level = <7>;
};
};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_18bit_pins_cfa10057
+ &lcdif_pins_cfa10057>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <18>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <30000000>;
+ hactive = <480>;
+ vactive = <800>;
+ hfront-porch = <12>;
+ hback-porch = <2>;
+ vfront-porch = <5>;
+ vback-porch = <3>;
+ hsync-len = <2>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&lradc {
+ fsl,lradc-touchscreen-wires = <4>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <100>;
+ status = "okay";
+};
+
+&pinctrl {
+ usb_pins_cfa10057: usb-10057@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_cfa10057: lcdif-evk@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm4_pins_a>;
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb1_vbus>;
+ pinctrl-0 = <&usb1_pins_a>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10058.dts b/arch/arm/boot/dts/imx28-cfa10058.dts
index 4465fd86785a..931c4d089b26 100644
--- a/arch/arm/boot/dts/imx28-cfa10058.dts
+++ b/arch/arm/boot/dts/imx28-cfa10058.dts
@@ -14,93 +14,6 @@ / {
model = "Crystalfontz CFA-10058 Board";
compatible = "crystalfontz,cfa10058", "crystalfontz,cfa10036", "fsl,imx28";
- apb@80000000 {
- apbh@80000000 {
- pinctrl@80018000 {
- usb_pins_cfa10058: usb-10058@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_D07__GPIO_0_7
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_cfa10058: lcdif-10058@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
-
- lcdif@80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_24bit_pins_a
- &lcdif_pins_cfa10058>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <30000000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <40>;
- hfront-porch = <40>;
- vback-porch = <13>;
- vfront-porch = <29>;
- hsync-len = <8>;
- vsync-len = <8>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
- };
- };
-
- apbx@80040000 {
- lradc@80050000 {
- fsl,lradc-touchscreen-wires = <4>;
- status = "okay";
- };
-
- pwm: pwm@80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm3_pins_b>;
- status = "okay";
- };
-
- usbphy1: usbphy@8007e000 {
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb1: usb@80090000 {
- vbus-supply = <®_usb1_vbus>;
- pinctrl-0 = <&usb1_pins_a>;
- pinctrl-names = "default";
- status = "okay";
- };
- };
-
regulators {
compatible = "simple-bus";
#address-cells = <1>;
@@ -118,17 +31,6 @@ reg_usb1_vbus: regulator@0 {
};
};
- ahb@80080000 {
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <100>;
- status = "okay";
- };
- };
-
backlight {
compatible = "pwm-backlight";
pwms = <&pwm 3 5000000>;
@@ -136,3 +38,91 @@ backlight {
default-brightness-level = <6>;
};
};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a
+ &lcdif_pins_cfa10058>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <30000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <40>;
+ hfront-porch = <40>;
+ vback-porch = <13>;
+ vfront-porch = <29>;
+ hsync-len = <8>;
+ vsync-len = <8>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&lradc {
+ fsl,lradc-touchscreen-wires = <4>;
+ status = "okay";
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <100>;
+ status = "okay";
+};
+
+&pinctrl {
+ usb_pins_cfa10058: usb-10058@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_cfa10058: lcdif-10058@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_pins_b>;
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb1_vbus>;
+ pinctrl-0 = <&usb1_pins_a>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH V2 5/9] ARM: dts: imx28-duckbill: Convert to use label references
2023-03-07 18:39 [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files Stefan Wahren
` (3 preceding siblings ...)
2023-03-07 18:40 ` [PATCH V2 4/9] ARM: dts: imx28-cfa10036: " Stefan Wahren
@ 2023-03-07 18:40 ` Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 6/9] ARM: dts: imx28-duckbill-2: Include base board Stefan Wahren
` (4 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Stefan Wahren @ 2023-03-07 18:40 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: linux-imx, devicetree, linux-arm-kernel, Stefan Wahren, Michael Heimpold
These I2SE board files still use node name and unit address
to reference parts from the imx28.dtsi . This causes a lot of
redundancy. So use label references in order to make it easier
to maintain.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Michael Heimpold <mhei@heimpold.de>
---
arch/arm/boot/dts/imx28-duckbill-2.dts | 256 ++++++++++++-------------
arch/arm/boot/dts/imx28-duckbill.dts | 196 +++++++++----------
2 files changed, 218 insertions(+), 234 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-duckbill-2.dts b/arch/arm/boot/dts/imx28-duckbill-2.dts
index 23fd3036404d..4e28212e9626 100644
--- a/arch/arm/boot/dts/imx28-duckbill-2.dts
+++ b/arch/arm/boot/dts/imx28-duckbill-2.dts
@@ -18,138 +18,6 @@ memory@40000000 {
reg = <0x40000000 0x08000000>;
};
- apb@80000000 {
- apbh@80000000 {
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_8bit_pins_a
- &mmc0_cd_cfg &mmc0_sck_cfg>;
- bus-width = <8>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
- non-removable;
- };
-
- ssp2: spi@80014000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_4bit_pins_b
- &mmc2_cd_cfg &mmc2_sck_cfg_b>;
- bus-width = <4>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
- };
-
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_phy_reset_pin: mac0-phy-reset@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_phy_int_pin: mac0-phy-int@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- led_pins: leds@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SAIF0_MCLK__GPIO_3_20
- MX28_PAD_SAIF0_LRCLK__GPIO_3_21
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
- };
-
- apbx@80040000 {
- lradc@80050000 {
- status = "okay";
- };
-
- i2c0: i2c@80058000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
- };
-
- auart0: serial@8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_2pins_a>;
- status = "okay";
- };
-
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
-
- usbphy0: usbphy@8007c000 {
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb0: usb@80080000 {
- status = "okay";
- dr_mode = "peripheral";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
- phy-supply = <®_3p3v>;
- phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <25>;
- phy-handle = <ðphy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy: ethernet-phy@0 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_phy_int_pin>;
- interrupt-parent = <&gpio0>;
- interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
- max-speed = <100>;
- };
- };
- };
- };
-
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
@@ -176,3 +44,127 @@ status-green {
};
};
};
+
+&auart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_2pins_a>;
+ status = "okay";
+};
+
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&lradc {
+ status = "okay";
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+ phy-supply = <®_3p3v>;
+ phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ phy-handle = <ðphy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_phy_int_pin>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+ max-speed = <100>;
+ };
+ };
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_reset_pin: mac0-phy-reset@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_int_pin: mac0-phy-int@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins: leds@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20
+ MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <8>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ non-removable;
+};
+
+&ssp2 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_4bit_pins_b
+ &mmc2_cd_cfg &mmc2_sck_cfg_b>;
+ bus-width = <4>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "peripheral";
+};
+
+&usbphy0 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-duckbill.dts b/arch/arm/boot/dts/imx28-duckbill.dts
index c666afb12445..13ffd533fdea 100644
--- a/arch/arm/boot/dts/imx28-duckbill.dts
+++ b/arch/arm/boot/dts/imx28-duckbill.dts
@@ -17,108 +17,6 @@ memory@40000000 {
reg = <0x40000000 0x08000000>;
};
- apb@80000000 {
- apbh@80000000 {
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_4bit_pins_a
- &mmc0_cd_cfg &mmc0_sck_cfg>;
- bus-width = <4>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
- };
-
- ssp2: spi@80014000 {
- compatible = "fsl,imx28-spi";
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- status = "okay";
- };
-
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_phy_reset_pin: mac0-phy-reset@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- led_pins: leds@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_AUART1_RX__GPIO_3_4
- MX28_PAD_AUART1_TX__GPIO_3_5
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
- };
-
- apbx@80040000 {
- lradc@80050000 {
- status = "okay";
- };
-
- i2c0: i2c@80058000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
- };
-
- auart0: serial@8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_2pins_a>;
- status = "okay";
- };
-
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
-
- usbphy0: usbphy@8007c000 {
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb0: usb@80080000 {
- status = "okay";
- dr_mode = "peripheral";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
- phy-supply = <®_3p3v>;
- phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <25>;
- status = "okay";
- };
- };
-
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
@@ -145,3 +43,97 @@ status-green {
};
};
};
+
+&auart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_2pins_a>;
+ status = "okay";
+};
+
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+};
+
+&lradc {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+ phy-supply = <®_3p3v>;
+ phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_reset_pin: mac0-phy-reset@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins: leds@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART1_RX__GPIO_3_4
+ MX28_PAD_AUART1_TX__GPIO_3_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <4>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&ssp2 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+};
+
+&usb0 {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy0 {
+ status = "okay";
+};
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH V2 6/9] ARM: dts: imx28-duckbill-2: Include base board
2023-03-07 18:39 [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files Stefan Wahren
` (4 preceding siblings ...)
2023-03-07 18:40 ` [PATCH V2 5/9] ARM: dts: imx28-duckbill: " Stefan Wahren
@ 2023-03-07 18:40 ` Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 7/9] ARM: dts: imx28-evk: Convert to use label references Stefan Wahren
` (3 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Stefan Wahren @ 2023-03-07 18:40 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: linux-imx, devicetree, linux-arm-kernel, Stefan Wahren, Michael Heimpold
All additional I2SE Duckbill 2 variants always have the same
base board in common. So consider this by including the base
board and avoid a lot of redundancy.
Special care needs to be taken of the SPI variant. ssp2 is used
as SD card interface on the base board, but on the SPI variant
it's downgrade to a SPI interface to connect the QCA7000. So
the SD card properties must be deleted.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Michael Heimpold <mhei@heimpold.de>
---
arch/arm/boot/dts/imx28-duckbill-2-485.dts | 174 ++-------------
.../arm/boot/dts/imx28-duckbill-2-enocean.dts | 198 +++-------------
arch/arm/boot/dts/imx28-duckbill-2-spi.dts | 211 ++++--------------
3 files changed, 81 insertions(+), 502 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-485.dts b/arch/arm/boot/dts/imx28-duckbill-2-485.dts
index d451fa018d83..b73020ff1053 100644
--- a/arch/arm/boot/dts/imx28-duckbill-2-485.dts
+++ b/arch/arm/boot/dts/imx28-duckbill-2-485.dts
@@ -5,172 +5,13 @@
*/
/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
+#include "imx28-duckbill-2.dts"
/ {
model = "I2SE Duckbill 2 485";
compatible = "i2se,duckbill-2-485", "i2se,duckbill-2", "fsl,imx28";
- memory@40000000 {
- device_type = "memory";
- reg = <0x40000000 0x08000000>;
- };
-
- apb@80000000 {
- apbh@80000000 {
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_8bit_pins_a
- &mmc0_cd_cfg &mmc0_sck_cfg>;
- bus-width = <8>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
- non-removable;
- };
-
- ssp2: spi@80014000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_4bit_pins_b
- &mmc2_cd_cfg &mmc2_sck_cfg_b>;
- bus-width = <4>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
- };
-
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_phy_reset_pin: mac0-phy-reset@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_phy_int_pin: mac0-phy-int@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- led_pins: leds@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SAIF0_MCLK__GPIO_3_20
- MX28_PAD_SAIF0_LRCLK__GPIO_3_21
- MX28_PAD_I2C0_SCL__GPIO_3_24
- MX28_PAD_I2C0_SDA__GPIO_3_25
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
- };
-
- apbx@80040000 {
- lradc@80050000 {
- status = "okay";
- };
-
- auart0: serial@8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_2pins_a>;
- status = "okay";
- };
-
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
-
- usbphy0: usbphy@8007c000 {
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb0: usb@80080000 {
- status = "okay";
- dr_mode = "peripheral";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
- phy-supply = <®_3p3v>;
- phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <25>;
- phy-handle = <ðphy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy: ethernet-phy@0 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_phy_int_pin>;
- interrupt-parent = <&gpio0>;
- interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
- max-speed = <100>;
- };
- };
- };
- };
-
- reg_3p3v: regulator-3p3v {
- compatible = "regulator-fixed";
- regulator-name = "3P3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins>;
-
- status-red {
- label = "duckbill:red:status";
- gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "default-on";
- };
-
- status-green {
- label = "duckbill:green:status";
- gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
-
rs485-red {
label = "duckbill:red:rs485";
gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
@@ -182,3 +23,16 @@ rs485-green {
};
};
};
+
+&i2c0 {
+ status = "disabled";
+};
+
+&led_pins {
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20
+ MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+ MX28_PAD_I2C0_SCL__GPIO_3_24
+ MX28_PAD_I2C0_SDA__GPIO_3_25
+ >;
+};
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
index 73f521c46c1e..473d99b9b42f 100644
--- a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
+++ b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
@@ -5,184 +5,14 @@
*/
/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
+#include "imx28-duckbill-2.dts"
/ {
model = "I2SE Duckbill 2 EnOcean";
compatible = "i2se,duckbill-2-enocean", "i2se,duckbill-2", "fsl,imx28";
- memory@40000000 {
- device_type = "memory";
- reg = <0x40000000 0x08000000>;
- };
-
- apb@80000000 {
- apbh@80000000 {
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_8bit_pins_a
- &mmc0_cd_cfg &mmc0_sck_cfg>;
- bus-width = <8>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
- non-removable;
- };
-
- ssp2: spi@80014000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_4bit_pins_b
- &mmc2_cd_cfg &mmc2_sck_cfg_b>;
- bus-width = <4>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
- };
-
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_phy_reset_pin: mac0-phy-reset@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_phy_int_pin: mac0-phy-int@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- led_pins: leds@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SAIF0_MCLK__GPIO_3_20
- MX28_PAD_SAIF0_LRCLK__GPIO_3_21
- MX28_PAD_AUART0_CTS__GPIO_3_2
- MX28_PAD_I2C0_SCL__GPIO_3_24
- MX28_PAD_I2C0_SDA__GPIO_3_25
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- enocean_button: enocean-button@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_AUART0_RTS__GPIO_3_3
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
- };
-
- apbx@80040000 {
- lradc@80050000 {
- status = "okay";
- };
-
- auart0: serial@8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_2pins_a>;
- status = "okay";
- };
-
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
-
- usbphy0: usbphy@8007c000 {
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb0: usb@80080000 {
- status = "okay";
- dr_mode = "peripheral";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
- phy-supply = <®_3p3v>;
- phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <25>;
- phy-handle = <ðphy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy: ethernet-phy@0 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_phy_int_pin>;
- interrupt-parent = <&gpio0>;
- interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
- max-speed = <100>;
- };
- };
- };
- };
-
- reg_3p3v: regulator-3p3v {
- compatible = "regulator-fixed";
- regulator-name = "3P3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins>;
-
- status-red {
- label = "duckbill:red:status";
- gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "default-on";
- };
-
- status-green {
- label = "duckbill:green:status";
- gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
-
enocean-blue {
label = "duckbill:blue:enocean";
gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
@@ -211,3 +41,29 @@ key-enocean {
};
};
};
+
+&i2c0 {
+ status = "disabled";
+};
+
+&led_pins {
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20
+ MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+ MX28_PAD_AUART0_CTS__GPIO_3_2
+ MX28_PAD_I2C0_SCL__GPIO_3_24
+ MX28_PAD_I2C0_SDA__GPIO_3_25
+ >;
+};
+
+&pinctrl {
+ enocean_button: enocean-button@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART0_RTS__GPIO_3_3
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-spi.dts b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
index 0e8be5975709..859d97a5a775 100644
--- a/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
+++ b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
@@ -5,9 +5,7 @@
*/
/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
+#include "imx28-duckbill-2.dts"
/ {
model = "I2SE Duckbill 2 SPI";
@@ -16,179 +14,50 @@ / {
aliases {
ethernet1 = &qca7000;
};
+};
- memory@40000000 {
- device_type = "memory";
- reg = <0x40000000 0x08000000>;
- };
-
- apb@80000000 {
- apbh@80000000 {
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_8bit_pins_a
- &mmc0_cd_cfg &mmc0_sck_cfg>;
- bus-width = <8>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
- non-removable;
- };
-
- ssp2: spi@80014000 {
- compatible = "fsl,imx28-spi";
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- status = "okay";
-
- qca7000: ethernet@0 {
- reg = <0>;
- compatible = "qca,qca7000";
- pinctrl-names = "default";
- pinctrl-0 = <&qca7000_pins>;
- interrupt-parent = <&gpio3>;
- interrupts = <3 IRQ_TYPE_EDGE_RISING>;
- spi-cpha;
- spi-cpol;
- spi-max-frequency = <8000000>;
- };
- };
-
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_phy_reset_pin: mac0-phy-reset@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_phy_int_pin: mac0-phy-int@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- led_pins: led@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SAIF0_MCLK__GPIO_3_20
- MX28_PAD_SAIF0_LRCLK__GPIO_3_21
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- qca7000_pins: qca7000@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_AUART0_RTS__GPIO_3_3 /* Interrupt */
- MX28_PAD_LCD_D13__GPIO_1_13 /* QCA7K reset */
- MX28_PAD_LCD_D14__GPIO_1_14 /* GPIO 0 */
- MX28_PAD_LCD_D15__GPIO_1_15 /* GPIO 1 */
- MX28_PAD_LCD_D18__GPIO_1_18 /* GPIO 2 */
- MX28_PAD_LCD_D21__GPIO_1_21 /* GPIO 3 */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
- };
-
- apbx@80040000 {
- lradc@80050000 {
- status = "okay";
- };
-
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
-
- usbphy0: usbphy@8007c000 {
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb0: usb@80080000 {
- status = "okay";
- dr_mode = "peripheral";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
- phy-supply = <®_3p3v>;
- phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <25>;
- phy-handle = <ðphy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
+&auart0 {
+ status = "disabled";
+};
- ethphy: ethernet-phy@0 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_phy_int_pin>;
- interrupt-parent = <&gpio0>;
- interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
- max-speed = <100>;
- };
- };
- };
- };
+&i2c0 {
+ status = "disabled";
+};
- reg_3p3v: regulator-3p3v {
- compatible = "regulator-fixed";
- regulator-name = "3P3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
+&pinctrl {
+ qca7000_pins: qca7000@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART0_RTS__GPIO_3_3 /* Interrupt */
+ MX28_PAD_LCD_D13__GPIO_1_13 /* QCA7K reset */
+ MX28_PAD_LCD_D14__GPIO_1_14 /* GPIO 0 */
+ MX28_PAD_LCD_D15__GPIO_1_15 /* GPIO 1 */
+ MX28_PAD_LCD_D18__GPIO_1_18 /* GPIO 2 */
+ MX28_PAD_LCD_D21__GPIO_1_21 /* GPIO 3 */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
+};
- leds {
- compatible = "gpio-leds";
+&ssp2 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ /delete-property/ bus-width;
+ /delete-property/ vmmc-supply;
+ status = "okay";
+
+ qca7000: ethernet@0 {
+ reg = <0>;
+ compatible = "qca,qca7000";
pinctrl-names = "default";
- pinctrl-0 = <&led_pins>;
-
- status-red {
- label = "duckbill:red:status";
- gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "default-on";
- };
-
- status-green {
- label = "duckbill:green:status";
- gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
+ pinctrl-0 = <&qca7000_pins>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ spi-cpha;
+ spi-cpol;
+ spi-max-frequency = <8000000>;
};
};
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH V2 7/9] ARM: dts: imx28-evk: Convert to use label references
2023-03-07 18:39 [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files Stefan Wahren
` (5 preceding siblings ...)
2023-03-07 18:40 ` [PATCH V2 6/9] ARM: dts: imx28-duckbill-2: Include base board Stefan Wahren
@ 2023-03-07 18:40 ` Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 8/9] ARM: dts: imx28-ts4600: " Stefan Wahren
` (2 subsequent siblings)
9 siblings, 0 replies; 11+ messages in thread
From: Stefan Wahren @ 2023-03-07 18:40 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: linux-imx, devicetree, linux-arm-kernel, Stefan Wahren
This Freescale board file still use node name and unit address
to reference parts from the imx28.dtsi . This causes a lot of
redundancy. So use label references in order to make it easier
to maintain.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
---
arch/arm/boot/dts/imx28-evk.dts | 462 ++++++++++++++++----------------
1 file changed, 227 insertions(+), 235 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
index 1053b7c584d8..783abb82b2a8 100644
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ b/arch/arm/boot/dts/imx28-evk.dts
@@ -95,266 +95,258 @@ panel_in: endpoint {
};
};
- apb@80000000 {
- apbh@80000000 {
- nand-controller@8000c000 {
- pinctrl-names = "default";
- pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg
- &gpmi_pins_evk>;
- status = "okay";
- };
+ sound {
+ compatible = "fsl,imx28-evk-sgtl5000",
+ "fsl,mxs-audio-sgtl5000";
+ model = "imx28-evk-sgtl5000";
+ saif-controllers = <&saif0 &saif1>;
+ audio-codec = <&sgtl5000>;
+ };
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_8bit_pins_a
- &mmc0_cd_cfg &mmc0_sck_cfg>;
- bus-width = <8>;
- wp-gpios = <&gpio2 12 0>;
- vmmc-supply = <®_vddio_sd0>;
- status = "okay";
- };
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pin_gpio3_5>;
- ssp1: spi@80012000 {
- compatible = "fsl,imx28-mmc";
- bus-width = <8>;
- wp-gpios = <&gpio0 28 0>;
- };
+ user {
+ label = "Heartbeat";
+ gpios = <&gpio3 5 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
- ssp2: spi@80014000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx28-spi";
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- status = "okay";
-
- flash: flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "sst,sst25vf016b", "jedec,spi-nor";
- spi-max-frequency = <40000000>;
- reg = <0>;
- };
- };
+ backlight_display: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 2 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ };
+};
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP1_CMD__GPIO_2_13
- MX28_PAD_SSP1_DATA3__GPIO_2_15
- MX28_PAD_ENET0_RX_CLK__GPIO_4_13
- MX28_PAD_SSP1_SCK__GPIO_2_12
- MX28_PAD_PWM3__GPIO_3_28
- MX28_PAD_LCD_RESET__GPIO_3_30
- MX28_PAD_AUART2_RX__GPIO_3_8
- MX28_PAD_AUART2_TX__GPIO_3_9
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- led_pin_gpio3_5: led_gpio3_5@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_AUART1_TX__GPIO_3_5
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- gpmi_pins_evk: gpmi-nand-evk@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_CE1N__GPMI_CE1N
- MX28_PAD_GPMI_RDY1__GPMI_READY1
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_evk: lcdif-evk@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
+&auart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_pins_a>;
+ uart-has-rtscts;
+ status = "okay";
+};
- lcdif@80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_24bit_pins_a
- &lcdif_pins_evk>;
- status = "okay";
-
- port {
- display_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
- };
+&auart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart3_pins_a>;
+ status = "okay";
+};
- can0: can@80032000 {
- pinctrl-names = "default";
- pinctrl-0 = <&can0_pins_a>;
- xceiver-supply = <®_can_3v3>;
- status = "okay";
- };
+&can0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can0_pins_a>;
+ xceiver-supply = <®_can_3v3>;
+ status = "okay";
+};
- can1: can@80034000 {
- pinctrl-names = "default";
- pinctrl-0 = <&can1_pins_a>;
- xceiver-supply = <®_can_3v3>;
- status = "okay";
- };
- };
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can1_pins_a>;
+ xceiver-supply = <®_can_3v3>;
+ status = "okay";
+};
- apbx@80040000 {
- saif0: saif@80042000 {
- pinctrl-names = "default";
- pinctrl-0 = <&saif0_pins_a>;
- status = "okay";
- };
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+};
- saif1: saif@80046000 {
- pinctrl-names = "default";
- pinctrl-0 = <&saif1_pins_a>;
- fsl,saif-master = <&saif0>;
- status = "okay";
- };
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg
+ &gpmi_pins_evk>;
+ status = "okay";
+};
- lradc@80050000 {
- status = "okay";
- fsl,lradc-touchscreen-wires = <4>;
- fsl,ave-ctrl = <4>;
- fsl,ave-delay = <2>;
- fsl,settling = <10>;
- };
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a
+ &lcdif_pins_evk>;
+ status = "okay";
- i2c0: i2c@80058000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- sgtl5000: codec@a {
- compatible = "fsl,sgtl5000";
- reg = <0x0a>;
- #sound-dai-cells = <0>;
- VDDA-supply = <®_3p3v>;
- VDDIO-supply = <®_3p3v>;
- clocks = <&saif0>;
- };
-
- at24@51 {
- compatible = "atmel,24c32";
- pagesize = <32>;
- reg = <0x51>;
- };
- };
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+};
- pwm: pwm@80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm2_pins_a>;
- status = "okay";
- };
+&lradc {
+ fsl,lradc-touchscreen-wires = <4>;
+ fsl,ave-ctrl = <4>;
+ fsl,ave-delay = <2>;
+ fsl,settling = <10>;
+ status = "okay";
+};
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ #sound-dai-cells = <0>;
+ VDDA-supply = <®_3p3v>;
+ VDDIO-supply = <®_3p3v>;
+ clocks = <&saif0>;
+ };
- auart0: serial@8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_pins_a>;
- uart-has-rtscts;
- status = "okay";
- };
+ at24@51 {
+ compatible = "atmel,24c32";
+ pagesize = <32>;
+ reg = <0x51>;
+ };
+};
- auart3: serial@80070000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart3_pins_a>;
- status = "okay";
- };
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-supply = <®_fec_3v3>;
+ phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <100>;
+ status = "okay";
+};
- usbphy0: usbphy@8007c000 {
- status = "okay";
- };
+&mac1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ status = "okay";
+};
- usbphy1: usbphy@8007e000 {
- status = "okay";
- };
- };
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP1_CMD__GPIO_2_13
+ MX28_PAD_SSP1_DATA3__GPIO_2_15
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+ MX28_PAD_SSP1_SCK__GPIO_2_12
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ MX28_PAD_AUART2_RX__GPIO_3_8
+ MX28_PAD_AUART2_TX__GPIO_3_9
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
- ahb@80080000 {
- usb0: usb@80080000 {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_pins_a>;
- vbus-supply = <®_usb0_vbus>;
- status = "okay";
- };
-
- usb1: usb@80090000 {
- vbus-supply = <®_usb1_vbus>;
- status = "okay";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- phy-supply = <®_fec_3v3>;
- phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <100>;
- status = "okay";
- };
+ led_pin_gpio3_5: led_gpio3_5@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART1_TX__GPIO_3_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
- mac1: ethernet@800f4000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac1_pins_a>;
- status = "okay";
- };
+ gpmi_pins_evk: gpmi-nand-evk@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_CE1N__GPMI_CE1N
+ MX28_PAD_GPMI_RDY1__GPMI_READY1
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
- sound {
- compatible = "fsl,imx28-evk-sgtl5000",
- "fsl,mxs-audio-sgtl5000";
- model = "imx28-evk-sgtl5000";
- saif-controllers = <&saif0 &saif1>;
- audio-codec = <&sgtl5000>;
+ lcdif_pins_evk: lcdif-evk@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
+};
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pin_gpio3_5>;
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2_pins_a>;
+ status = "okay";
+};
- user {
- label = "Heartbeat";
- gpios = <&gpio3 5 0>;
- linux,default-trigger = "heartbeat";
- };
- };
+&saif0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif0_pins_a>;
+ status = "okay";
+};
- backlight_display: backlight {
- compatible = "pwm-backlight";
- pwms = <&pwm 2 5000000>;
- brightness-levels = <0 4 8 16 32 64 128 255>;
- default-brightness-level = <6>;
+&saif1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif1_pins_a>;
+ fsl,saif-master = <&saif0>;
+ status = "okay";
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <8>;
+ wp-gpios = <&gpio2 12 0>;
+ vmmc-supply = <®_vddio_sd0>;
+ status = "okay";
+};
+
+&ssp1 {
+ compatible = "fsl,imx28-mmc";
+ bus-width = <8>;
+ wp-gpios = <&gpio0 28 0>;
+};
+
+&ssp2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+
+ flash: flash@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "sst,sst25vf016b", "jedec,spi-nor";
+ spi-max-frequency = <40000000>;
};
};
+
+&usb0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_pins_a>;
+ vbus-supply = <®_usb0_vbus>;
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
+
+&usbphy0 {
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH V2 8/9] ARM: dts: imx28-ts4600: Convert to use label references
2023-03-07 18:39 [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files Stefan Wahren
` (6 preceding siblings ...)
2023-03-07 18:40 ` [PATCH V2 7/9] ARM: dts: imx28-evk: Convert to use label references Stefan Wahren
@ 2023-03-07 18:40 ` Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 9/9] ARM: dts: imx28-tx28: add SPDX-License-Identifier Stefan Wahren
2023-03-14 6:43 ` [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files Shawn Guo
9 siblings, 0 replies; 11+ messages in thread
From: Stefan Wahren @ 2023-03-07 18:40 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: linux-imx, devicetree, linux-arm-kernel, Stefan Wahren
This Technologic board file still use node name and unit address
to reference parts from the imx28.dtsi . This causes a lot of
redundancy. So use label references in order to make it easier
to maintain.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
---
arch/arm/boot/dts/imx28-ts4600.dts | 80 ++++++++++++++----------------
1 file changed, 36 insertions(+), 44 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-ts4600.dts b/arch/arm/boot/dts/imx28-ts4600.dts
index 0d58da1c0cc5..ae6ed5c41be3 100644
--- a/arch/arm/boot/dts/imx28-ts4600.dts
+++ b/arch/arm/boot/dts/imx28-ts4600.dts
@@ -18,50 +18,6 @@ memory@40000000 {
reg = <0x40000000 0x10000000>; /* 256MB */
};
- apb@80000000 {
- apbh@80000000 {
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_4bit_pins_a
- &mmc0_sck_cfg
- &en_sd_pwr>;
- broken-cd;
- bus-width = <4>;
- vmmc-supply = <®_vddio_sd0>;
- status = "okay";
- };
-
- pinctrl@80018000 {
-
- en_sd_pwr: en-sd-pwr@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_PWM3__GPIO_3_28
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- };
- };
-
- apbx@80040000 {
- pwm: pwm@80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm2_pins_a>;
- status = "okay";
- };
-
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
- };
- };
-
reg_vddio_sd0: regulator-vddio-sd0 {
compatible = "regulator-fixed";
regulator-name = "vddio-sd0";
@@ -72,3 +28,39 @@ reg_vddio_sd0: regulator-vddio-sd0 {
};
};
+
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+};
+
+&pinctrl {
+ en_sd_pwr: en-sd-pwr@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_PWM3__GPIO_3_28
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2_pins_a>;
+ status = "okay";
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a
+ &mmc0_sck_cfg
+ &en_sd_pwr>;
+ broken-cd;
+ bus-width = <4>;
+ vmmc-supply = <®_vddio_sd0>;
+ status = "okay";
+};
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH V2 9/9] ARM: dts: imx28-tx28: add SPDX-License-Identifier
2023-03-07 18:39 [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files Stefan Wahren
` (7 preceding siblings ...)
2023-03-07 18:40 ` [PATCH V2 8/9] ARM: dts: imx28-ts4600: " Stefan Wahren
@ 2023-03-07 18:40 ` Stefan Wahren
2023-03-14 6:43 ` [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files Shawn Guo
9 siblings, 0 replies; 11+ messages in thread
From: Stefan Wahren @ 2023-03-07 18:40 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: linux-imx, devicetree, linux-arm-kernel, Stefan Wahren,
Lothar Waßmann
Replace the license blob by a clean SPDX-License-Identifier with GPL2
or MIT even if X11 is specified in the original blob since the actual
license text corresponds to a MIT license.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx28-tx28.dts | 38 +-------------------------------
1 file changed, 1 insertion(+), 37 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-tx28.dts b/arch/arm/boot/dts/imx28-tx28.dts
index 096f246032c6..ffe58c7093e1 100644
--- a/arch/arm/boot/dts/imx28-tx28.dts
+++ b/arch/arm/boot/dts/imx28-tx28.dts
@@ -1,43 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
/*
* Copyright 2012 Shawn Guo <shawn.guo@linaro.org>
* Copyright 2013-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread
* Re: [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files
2023-03-07 18:39 [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files Stefan Wahren
` (8 preceding siblings ...)
2023-03-07 18:40 ` [PATCH V2 9/9] ARM: dts: imx28-tx28: add SPDX-License-Identifier Stefan Wahren
@ 2023-03-14 6:43 ` Shawn Guo
9 siblings, 0 replies; 11+ messages in thread
From: Shawn Guo @ 2023-03-14 6:43 UTC (permalink / raw)
To: Stefan Wahren
Cc: Rob Herring, Krzysztof Kozlowski, Sascha Hauer, Fabio Estevam,
linux-imx, devicetree, linux-arm-kernel
On Tue, Mar 07, 2023 at 07:39:58PM +0100, Stefan Wahren wrote:
> Since the imx28 belongs to the early ARM platforms which has been
> adapted to DT, a lot of these DTS files are not in the best shape.
> So this series tries to address this by using label references
> and SPDX tags.
>
> Theses patches doesn't include functional changes. The resulting
> DTB files has been verified with dtdiff.
>
> Changes in V2:
> - fix alphabetical order of i2c label reference in patch 1
> - add Wolfgang Grandegger in Cc for patch 2
> - replace Anson's address in patch 7 with linux-imx@nxp.com because
> his address isn't available anymore
> - remove Cc from patch 8 because the address isn't available anymore
> - add Acked-by for patch 9
>
> Stefan Wahren (9):
> ARM: dts: imx28-apf28: Convert to use label references
> ARM: dts: imx28-m28/sps1: Convert to use label references
> ARM: dts: imx28-apx4devkit: Convert to use label references
> ARM: dts: imx28-cfa10036: Convert to use label references
> ARM: dts: imx28-duckbill: Convert to use label references
> ARM: dts: imx28-duckbill-2: Include base board
> ARM: dts: imx28-evk: Convert to use label references
> ARM: dts: imx28-ts4600: Convert to use label references
> ARM: dts: imx28-tx28: add SPDX-License-Identifier
Applied all, thanks!
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2023-03-14 6:44 UTC | newest]
Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-03-07 18:39 [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files Stefan Wahren
2023-03-07 18:39 ` [PATCH V2 1/9] ARM: dts: imx28-apf28: Convert to use label references Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 2/9] ARM: dts: imx28-m28/sps1: " Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 3/9] ARM: dts: imx28-apx4devkit: " Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 4/9] ARM: dts: imx28-cfa10036: " Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 5/9] ARM: dts: imx28-duckbill: " Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 6/9] ARM: dts: imx28-duckbill-2: Include base board Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 7/9] ARM: dts: imx28-evk: Convert to use label references Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 8/9] ARM: dts: imx28-ts4600: " Stefan Wahren
2023-03-07 18:40 ` [PATCH V2 9/9] ARM: dts: imx28-tx28: add SPDX-License-Identifier Stefan Wahren
2023-03-14 6:43 ` [PATCH V2 0/9] ARM: dts: imx28: Clean up older DTS files Shawn Guo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).