[PATCH 0/3] ARM: at91: at91sam9n12ek: enable usb gadget support

[PATCH 0/3] ARM: at91: at91sam9n12ek: enable usb gadget support

[Bo Shen]

This patch series enable the usb gadget support on at91sam9n12ek
board. On at91sam9n12 SoC which integrate the full speed udc device.


Bo Shen (3):
  USB: gadget: at91_udc: add at91sam9n12 support
  ARM: at91: dt: at91sam9n12: add udp device node
  ARM: at91: dt: at91sam9n12ek: enable udp

 arch/arm/boot/dts/at91sam9n12.dtsi  | 9 +++++++++
 arch/arm/boot/dts/at91sam9n12ek.dts | 5 +++++
 drivers/usb/gadget/udc/at91_udc.c   | 9 ++++++---
 3 files changed, 20 insertions(+), 3 deletions(-)

-- 
2.3.0.rc0

[PATCH 1/3] USB: gadget: at91_udc: add at91sam9n12 support

[Bo Shen]

Add at91sam9n12 SoC support.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
---

 drivers/usb/gadget/udc/at91_udc.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/gadget/udc/at91_udc.c b/drivers/usb/gadget/udc/at91_udc.c
index c862656..f4c785f 100644
--- a/drivers/usb/gadget/udc/at91_udc.c
+++ b/drivers/usb/gadget/udc/at91_udc.c
@@ -931,7 +931,8 @@ static void pullup(struct at91_udc *udc, int is_on)
 		at91_udp_write(udc, AT91_UDP_TXVC, 0);
 		if (cpu_is_at91rm9200())
 			gpio_set_value(udc->board.pullup_pin, active);
-		else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) {
+		else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() ||
+			 cpu_is_at91sam9g20() || cpu_is_at91sam9n12()) {
 			u32	txvc = at91_udp_read(udc, AT91_UDP_TXVC);
 
 			txvc |= AT91_UDP_TXVC_PUON;
@@ -949,7 +950,8 @@ static void pullup(struct at91_udc *udc, int is_on)
 		at91_udp_write(udc, AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS);
 		if (cpu_is_at91rm9200())
 			gpio_set_value(udc->board.pullup_pin, !active);
-		else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) {
+		else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() ||
+			 cpu_is_at91sam9g20() || cpu_is_at91sam9n12()) {
 			u32	txvc = at91_udp_read(udc, AT91_UDP_TXVC);
 
 			txvc &= ~AT91_UDP_TXVC_PUON;
@@ -1758,7 +1760,8 @@ static int at91udc_probe(struct platform_device *pdev)
 	}
 
 	/* newer chips have more FIFO memory than rm9200 */
-	if (cpu_is_at91sam9260() || cpu_is_at91sam9g20()) {
+	if (cpu_is_at91sam9260() || cpu_is_at91sam9g20() ||
+	    cpu_is_at91sam9n12()) {
 		udc->ep[0].maxpacket = 64;
 		udc->ep[3].maxpacket = 64;
 		udc->ep[4].maxpacket = 512;
-- 
2.3.0.rc0

[PATCH 2/3] ARM: at91: dt: at91sam9n12: add udp device node

[Bo Shen]

Add usb device node for at91sam9n12.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
---

 arch/arm/boot/dts/at91sam9n12.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi
index 68eb9ad..6120e03 100644
--- a/arch/arm/boot/dts/at91sam9n12.dtsi
+++ b/arch/arm/boot/dts/at91sam9n12.dtsi
@@ -901,6 +901,15 @@
 				clocks = <&pwm_clk>;
 				status = "disabled";
 			};
+
+			usb1: gadget at f803c000 {
+				compatible = "atmel,at91rm9200-udc";
+				reg = <0xf803c000 0x4000>;
+				interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
+				clocks = <&usb>, <&udphs_clk>, <&udpck>;
+				clock-names = "usb_clk", "udc_clk", "udpck";
+				status = "disabled";
+			};
 		};
 
 		nand0: nand at 40000000 {
-- 
2.3.0.rc0

[PATCH 3/3] ARM: at91: dt: at91sam9n12ek: enable udp

[Bo Shen]

Enable usb device port on at91sam9n12ek board.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
---

 arch/arm/boot/dts/at91sam9n12ek.dts | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts
index 13bb24e..3e572e5 100644
--- a/arch/arm/boot/dts/at91sam9n12ek.dts
+++ b/arch/arm/boot/dts/at91sam9n12ek.dts
@@ -120,6 +120,11 @@
 				};
 			};
 
+			usb1: gadget at f803c000 {
+				atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
+				status = "okay";
+			};
+
 			watchdog at fffffe40 {
 				status = "okay";
 			};
-- 
2.3.0.rc0

[PATCH 3/3] ARM: at91: dt: at91sam9n12ek: enable udp

[Sylvain Rochet]

Hello Bo,

On Mon, Feb 09, 2015 at 05:02:52PM +0800, Bo Shen wrote:
> Enable usb device port on at91sam9n12ek board.
> 
> Signed-off-by: Bo Shen <voice.shen@atmel.com>
> ---
> 
>  arch/arm/boot/dts/at91sam9n12ek.dts | 5 +++++
>  1 file changed, 5 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts
> index 13bb24e..3e572e5 100644
> --- a/arch/arm/boot/dts/at91sam9n12ek.dts
> +++ b/arch/arm/boot/dts/at91sam9n12ek.dts
> @@ -120,6 +120,11 @@
>  				};
>  			};
>  
> +			usb1: gadget at f803c000 {
> +				atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
> +				status = "okay";
> +			};
> +

There is an external resistor divider on PB16, acting like a pull-down 
(R22+R23). PB16 reset state is input, pull-up, schmitt trigger, you need 
to disable the pull-up in pinctrl this way:

usb1: gadget at f803c000 {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_board_usb1>;
	?
}

pinctrl ? {
	usb1 {
		pinctrl_board_usb1: usb1-board {
			atmel,pins = <AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;    /* PB16, no pull up and deglitch */
		};
	};
};


Sylvain

[PATCH 3/3] ARM: at91: dt: at91sam9n12ek: enable udp

[Bo Shen]

Hi Sylvain,

On 02/09/2015 06:04 PM, Sylvain Rochet wrote:
> Hello Bo,
>
> On Mon, Feb 09, 2015 at 05:02:52PM +0800, Bo Shen wrote:
>> Enable usb device port on at91sam9n12ek board.
>>
>> Signed-off-by: Bo Shen <voice.shen@atmel.com>
>> ---
>>
>>   arch/arm/boot/dts/at91sam9n12ek.dts | 5 +++++
>>   1 file changed, 5 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts
>> index 13bb24e..3e572e5 100644
>> --- a/arch/arm/boot/dts/at91sam9n12ek.dts
>> +++ b/arch/arm/boot/dts/at91sam9n12ek.dts
>> @@ -120,6 +120,11 @@
>>   				};
>>   			};
>>
>> +			usb1: gadget at f803c000 {
>> +				atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
>> +				status = "okay";
>> +			};
>> +
>
> There is an external resistor divider on PB16, acting like a pull-down
> (R22+R23). PB16 reset state is input, pull-up, schmitt trigger, you need
> to disable the pull-up in pinctrl this way:
>
> usb1: gadget at f803c000 {
> 	pinctrl-names = "default";
> 	pinctrl-0 = <&pinctrl_board_usb1>;
> 	?
> }
>
> pinctrl ? {
> 	usb1 {
> 		pinctrl_board_usb1: usb1-board {
> 			atmel,pins = <AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;    /* PB16, no pull up and deglitch */
> 		};
> 	};
> };

Thanks.

I will add it in next version.

>
> Sylvain
>

Best Regards,
Bo Shen

[PATCH 1/3] USB: gadget: at91_udc: add at91sam9n12 support

[Alexandre Belloni]

Hi Bo,

On 09/02/2015 at 17:02:50 +0800, Bo Shen wrote :
> Add at91sam9n12 SoC support.
> 
> Signed-off-by: Bo Shen <voice.shen@atmel.com>
> ---
> 
>  drivers/usb/gadget/udc/at91_udc.c | 9 ++++++---
>  1 file changed, 6 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/usb/gadget/udc/at91_udc.c b/drivers/usb/gadget/udc/at91_udc.c
> index c862656..f4c785f 100644
> --- a/drivers/usb/gadget/udc/at91_udc.c
> +++ b/drivers/usb/gadget/udc/at91_udc.c
> @@ -931,7 +931,8 @@ static void pullup(struct at91_udc *udc, int is_on)
>  		at91_udp_write(udc, AT91_UDP_TXVC, 0);
>  		if (cpu_is_at91rm9200())
>  			gpio_set_value(udc->board.pullup_pin, active);
> -		else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) {
> +		else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() ||
> +			 cpu_is_at91sam9g20() || cpu_is_at91sam9n12()) {

cpu_is_at91xx have been removed from the kernel, using the correct
compatible should be enough, see
http://git.kernel.org/cgit/linux/kernel/git/next/linux-next.git/commit/drivers/usb/gadget/udc/at91_udc.c?id=f0bceab4e3b528e799aba8fda8d2936fcfd41f1f


>  			u32	txvc = at91_udp_read(udc, AT91_UDP_TXVC);
>  
>  			txvc |= AT91_UDP_TXVC_PUON;
> @@ -949,7 +950,8 @@ static void pullup(struct at91_udc *udc, int is_on)
>  		at91_udp_write(udc, AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS);
>  		if (cpu_is_at91rm9200())
>  			gpio_set_value(udc->board.pullup_pin, !active);
> -		else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) {
> +		else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() ||
> +			 cpu_is_at91sam9g20() || cpu_is_at91sam9n12()) {
>  			u32	txvc = at91_udp_read(udc, AT91_UDP_TXVC);
>  
>  			txvc &= ~AT91_UDP_TXVC_PUON;
> @@ -1758,7 +1760,8 @@ static int at91udc_probe(struct platform_device *pdev)
>  	}
>  
>  	/* newer chips have more FIFO memory than rm9200 */
> -	if (cpu_is_at91sam9260() || cpu_is_at91sam9g20()) {
> +	if (cpu_is_at91sam9260() || cpu_is_at91sam9g20() ||
> +	    cpu_is_at91sam9n12()) {
>  		udc->ep[0].maxpacket = 64;
>  		udc->ep[3].maxpacket = 64;
>  		udc->ep[4].maxpacket = 512;
> -- 
> 2.3.0.rc0
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 1/3] USB: gadget: at91_udc: add at91sam9n12 support

[Bo Shen]

Hi Alexandre,

On 02/09/2015 07:14 PM, Alexandre Belloni wrote:
> Hi Bo,
>
> On 09/02/2015 at 17:02:50 +0800, Bo Shen wrote :
>> Add at91sam9n12 SoC support.
>>
>> Signed-off-by: Bo Shen <voice.shen@atmel.com>
>> ---
>>
>>   drivers/usb/gadget/udc/at91_udc.c | 9 ++++++---
>>   1 file changed, 6 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/usb/gadget/udc/at91_udc.c b/drivers/usb/gadget/udc/at91_udc.c
>> index c862656..f4c785f 100644
>> --- a/drivers/usb/gadget/udc/at91_udc.c
>> +++ b/drivers/usb/gadget/udc/at91_udc.c
>> @@ -931,7 +931,8 @@ static void pullup(struct at91_udc *udc, int is_on)
>>   		at91_udp_write(udc, AT91_UDP_TXVC, 0);
>>   		if (cpu_is_at91rm9200())
>>   			gpio_set_value(udc->board.pullup_pin, active);
>> -		else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) {
>> +		else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() ||
>> +			 cpu_is_at91sam9g20() || cpu_is_at91sam9n12()) {
>
> cpu_is_at91xx have been removed from the kernel, using the correct
> compatible should be enough, see
> http://git.kernel.org/cgit/linux/kernel/git/next/linux-next.git/commit/drivers/usb/gadget/udc/at91_udc.c?id=f0bceab4e3b528e799aba8fda8d2936fcfd41f1f

Thanks for you information. Missing this patch, check the next-20150209, 
it is here. I will base on next-20150209, so this patch no need anymore, 
only need to change the dts(i) file now.

Thanks again.

>
>>   			u32	txvc = at91_udp_read(udc, AT91_UDP_TXVC);
>>
>>   			txvc |= AT91_UDP_TXVC_PUON;
>> @@ -949,7 +950,8 @@ static void pullup(struct at91_udc *udc, int is_on)
>>   		at91_udp_write(udc, AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS);
>>   		if (cpu_is_at91rm9200())
>>   			gpio_set_value(udc->board.pullup_pin, !active);
>> -		else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) {
>> +		else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() ||
>> +			 cpu_is_at91sam9g20() || cpu_is_at91sam9n12()) {
>>   			u32	txvc = at91_udp_read(udc, AT91_UDP_TXVC);
>>
>>   			txvc &= ~AT91_UDP_TXVC_PUON;
>> @@ -1758,7 +1760,8 @@ static int at91udc_probe(struct platform_device *pdev)
>>   	}
>>
>>   	/* newer chips have more FIFO memory than rm9200 */
>> -	if (cpu_is_at91sam9260() || cpu_is_at91sam9g20()) {
>> +	if (cpu_is_at91sam9260() || cpu_is_at91sam9g20() ||
>> +	    cpu_is_at91sam9n12()) {
>>   		udc->ep[0].maxpacket = 64;
>>   		udc->ep[3].maxpacket = 64;
>>   		udc->ep[4].maxpacket = 512;
>> --
>> 2.3.0.rc0

Best Regards,
Bo Shen