Re: [PATCH 7/8] arm64: dts: allwinner: Add Allwinner H616 .dtsi file

[Icenowy Zheng <icenowy@aosc.io>]

于 2020年12月3日 GMT+08:00 上午12:05:04, Maxime Ripard <maxime@cerno.tech> 写到:
>On Wed, Dec 02, 2020 at 01:54:08PM +0000, Andre Przywara wrote:
>> This (relatively) new SoC is similar to the H6, but drops the
>(broken)
>> PCIe support and the USB 3.0 controller. It also gets the management
>> controller removed, which in turn removes *some*, but not all of the
>> devices formerly dedicated to the ARISC (CPUS).
>> There does not seem to be an external interrupt controller anymore,
>so
>> no external interrupts through an NMI pin. The AXP driver needs to
>learn
>> living with that.
>> 
>> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
>> ---
>>  .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 704
>++++++++++++++++++
>>  1 file changed, 704 insertions(+)
>>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
>> 
>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
>b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
>> new file mode 100644
>> index 000000000000..dcffbfdcd26b
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
>> @@ -0,0 +1,704 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +// Copyright (C) 2020 Arm Ltd.
>> +// based on the H6 dtsi, which is:
>> +//   Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
>> +
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/clock/sun50i-h616-ccu.h>
>> +#include <dt-bindings/clock/sun50i-h6-r-ccu.h>
>> +#include <dt-bindings/reset/sun50i-h616-ccu.h>
>> +#include <dt-bindings/reset/sun50i-h6-r-ccu.h>
>> +
>> +/ {
>> +	interrupt-parent = <&gic>;
>> +	#address-cells = <2>;
>> +	#size-cells = <2>;
>> +
>> +	cpus {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		cpu0: cpu@0 {
>> +			compatible = "arm,cortex-a53";
>> +			device_type = "cpu";
>> +			reg = <0>;
>> +			enable-method = "psci";
>> +			clocks = <&ccu CLK_CPUX>;
>> +		};
>> +
>> +		cpu1: cpu@1 {
>> +			compatible = "arm,cortex-a53";
>> +			device_type = "cpu";
>> +			reg = <1>;
>> +			enable-method = "psci";
>> +			clocks = <&ccu CLK_CPUX>;
>> +		};
>> +
>> +		cpu2: cpu@2 {
>> +			compatible = "arm,cortex-a53";
>> +			device_type = "cpu";
>> +			reg = <2>;
>> +			enable-method = "psci";
>> +			clocks = <&ccu CLK_CPUX>;
>> +		};
>> +
>> +		cpu3: cpu@3 {
>> +			compatible = "arm,cortex-a53";
>> +			device_type = "cpu";
>> +			reg = <3>;
>> +			enable-method = "psci";
>> +			clocks = <&ccu CLK_CPUX>;
>> +		};
>> +	};
>> +
>> +	reserved-memory {
>> +		#address-cells = <2>;
>> +		#size-cells = <2>;
>> +		ranges;
>> +
>> +		/* 512KiB reserved for ARM Trusted Firmware (BL31) */
>> +		secmon_reserved: secmon@40000000 {
>> +			reg = <0x0 0x40000000 0x0 0x80000>;
>> +			no-map;
>> +		};
>> +	};
>
>I'm not sure why that node is there, the previous SoCs didn't have it?

Previously we (ab)use SRAM A2 (designed for ARISC) for ATF.
But H616 has no SRAM A2.

>Shouldn't ATF patch it itself?
>
>> +	osc24M: osc24M_clk {
>> +		#clock-cells = <0>;
>> +		compatible = "fixed-clock";
>> +		clock-frequency = <24000000>;
>> +		clock-output-names = "osc24M";
>> +	};
>> +
>> +	pmu {
>> +		compatible = "arm,cortex-a53-pmu";
>> +		interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
>> +			     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
>> +			     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
>> +			     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
>> +		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
>> +	};
>> +
>> +	psci {
>> +		compatible = "arm,psci-0.2";
>> +		method = "smc";
>> +	};
>> +
>> +	timer {
>> +		compatible = "arm,armv8-timer";
>> +		arm,no-tick-in-suspend;
>
>This was tested with crust I assume?
>
>> +		interrupts = <GIC_PPI 13
>> +			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
>> +			     <GIC_PPI 14
>> +			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
>> +			     <GIC_PPI 11
>> +			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
>> +			     <GIC_PPI 10
>> +			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
>> +	};
>> +
>> +	soc {
>> +		compatible = "simple-bus";
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges = <0x0 0x0 0x0 0x40000000>;
>> +
>> +		syscon: syscon@3000000 {
>> +			compatible = "allwinner,sun50i-h616-system-control",
>
>That compatible isn't documented
>
>> +				     "allwinner,sun50i-a64-system-control";
>> +			reg = <0x03000000 0x1000>;
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			ranges;
>> +
>> +			sram_c: sram@28000 {
>> +				compatible = "mmio-sram";
>> +				reg = <0x00028000 0x30000>;
>> +				#address-cells = <1>;
>> +				#size-cells = <1>;
>> +				ranges = <0 0x00028000 0x30000>;
>> +			};
>> +
>> +			sram_c1: sram@1a00000 {
>> +				compatible = "mmio-sram";
>> +				reg = <0x01a00000 0x200000>;
>> +				#address-cells = <1>;
>> +				#size-cells = <1>;
>> +				ranges = <0 0x01a00000 0x200000>;
>> +
>> +				ve_sram: sram-section@0 {
>> +					compatible = "allwinner,sun50i-h616-sram-c1",
>
>Ditto
>
>> +						     "allwinner,sun4i-a10-sram-c1";
>> +					reg = <0x000000 0x200000>;
>> +				};
>> +			};
>> +		};
>> +
>> +		ccu: clock@3001000 {
>> +			compatible = "allwinner,sun50i-h616-ccu";
>
>Ditto
>
>> +			reg = <0x03001000 0x1000>;
>> +			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>;
>> +			clock-names = "hosc", "losc", "iosc";
>> +			#clock-cells = <1>;
>> +			#reset-cells = <1>;
>> +		};
>> +
>> +		watchdog: watchdog@30090a0 {
>> +			compatible = "allwinner,sun50i-h616-wdt",
>
>Ditto. I guess you can just run checkpatch there, it will let you know
>all the ones that aren't documented :)
>
>> +				     "allwinner,sun6i-a31-wdt";
>> +			reg = <0x030090a0 0x20>;
>> +			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&osc24M>;
>> +			status = "disabled";
>> +		};
>> +
>> +		pio: pinctrl@300b000 {
>> +			compatible = "allwinner,sun50i-h616-pinctrl";
>> +			reg = <0x0300b000 0x400>;
>> +			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>;
>> +			clock-names = "apb", "hosc", "losc";
>> +			gpio-controller;
>> +			#gpio-cells = <3>;
>> +			interrupt-controller;
>> +			#interrupt-cells = <3>;
>> +
>> +			ext_rgmii_pins: rgmii-pins {
>> +				pins = "PI0", "PI1", "PI2", "PI3", "PI4",
>> +				       "PI5", "PI7", "PI8", "PI9", "PI10",
>> +				       "PI11", "PI12", "PI13", "PI14", "PI15",
>> +				       "PI16";
>> +				function = "emac0";
>> +				drive-strength = <40>;
>> +			};
>> +
>> +			i2c0_pins: i2c0-pins {
>> +				pins = "PI6", "PI7";
>> +				function = "i2c0";
>> +			};
>> +
>> +			i2c3_pins_a: i2c1-pins-a {
>
>I guess you meant i2c3 in the node name?
>
>The pin groups with multiple options also are supposed to have the pin
>bank instead of the _a or _b suffix, so i2c3_ph_pins 
>
>> +				pins = "PH4", "PH5";
>> +				function = "i2c3";
>> +			};
>> +
>> +			ir_rx_pin: ir_rx_pin {
>> +				pins = "PH10";
>> +				function = "ir_rx";
>> +			};
>> +
>> +			mmc0_pins: mmc0-pins {
>> +				pins = "PF0", "PF1", "PF2", "PF3",
>> +				       "PF4", "PF5";
>> +				function = "mmc0";
>> +				drive-strength = <30>;
>> +				bias-pull-up;
>> +			};
>> +
>> +			mmc1_pins: mmc1-pins {
>> +				pins = "PG0", "PG1", "PG2", "PG3",
>> +				       "PG4", "PG5";
>> +				function = "mmc1";
>> +				drive-strength = <30>;
>> +				bias-pull-up;
>> +			};
>> +
>> +			mmc2_pins: mmc2-pins {
>> +				pins = "PC0", "PC1", "PC5", "PC6",
>> +				       "PC8", "PC9", "PC10", "PC11",
>> +				       "PC13", "PC14", "PC15", "PC16";
>> +				function = "mmc2";
>> +				drive-strength = <30>;
>> +				bias-pull-up;
>> +			};
>> +
>> +			spi0_pins: spi0-pins {
>> +				pins = "PC0", "PC2", "PC3", "PC4";
>> +				function = "spi0";
>> +			};
>> +
>> +			spi1_pins: spi1-pins {
>> +				pins = "PH6", "PH7", "PH8";
>> +				function = "spi1";
>> +			};
>> +
>> +			spi1_cs_pin: spi1-cs-pin {
>> +				pins = "PH5";
>> +				function = "spi1";
>> +			};
>> +
>> +			uart0_ph_pins: uart0-ph-pins {
>> +				pins = "PH0", "PH1";
>> +				function = "uart0";
>> +			};
>> +
>> +			uart1_pins: uart1-pins {
>> +				pins = "PG6", "PG7";
>> +				function = "uart1";
>> +			};
>> +
>> +			uart1_rts_cts_pins: uart1-rts-cts-pins {
>> +				pins = "PG8", "PG9";
>> +				function = "uart1";
>> +			};
>> +		};
>> +
>> +		gic: interrupt-controller@3021000 {
>> +			compatible = "arm,gic-400";
>> +			reg = <0x03021000 0x1000>,
>> +			      <0x03022000 0x2000>,
>> +			      <0x03024000 0x2000>,
>> +			      <0x03026000 0x2000>;
>> +			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
>IRQ_TYPE_LEVEL_HIGH)>;
>> +			interrupt-controller;
>> +			#interrupt-cells = <3>;
>> +		};
>> +
>> +		mmc0: mmc@4020000 {
>> +			compatible = "allwinner,sun50i-h616-mmc",
>> +				     "allwinner,sun50i-a100-mmc";
>> +			reg = <0x04020000 0x1000>;
>> +			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
>> +			clock-names = "ahb", "mmc";
>> +			resets = <&ccu RST_BUS_MMC0>;
>> +			reset-names = "ahb";
>> +			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&mmc0_pins>;
>> +			status = "disabled";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +		};
>> +
>> +		mmc1: mmc@4021000 {
>> +			compatible = "allwinner,sun50i-h616-mmc",
>> +				     "allwinner,sun50i-a100-mmc";
>> +			reg = <0x04021000 0x1000>;
>> +			clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
>> +			clock-names = "ahb", "mmc";
>> +			resets = <&ccu RST_BUS_MMC1>;
>> +			reset-names = "ahb";
>> +			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&mmc1_pins>;
>> +			status = "disabled";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +		};
>> +
>> +		mmc2: mmc@4022000 {
>> +			compatible = "allwinner,sun50i-h616-emmc",
>> +				     "allwinner,sun50i-a64-emmc";
>> +			reg = <0x04022000 0x1000>;
>> +			clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
>> +			clock-names = "ahb", "mmc";
>> +			resets = <&ccu RST_BUS_MMC2>;
>> +			reset-names = "ahb";
>> +			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&mmc2_pins>;
>> +			status = "disabled";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +		};
>> +
>> +		uart0: serial@5000000 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x05000000 0x400>;
>> +			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&ccu CLK_BUS_UART0>;
>> +			resets = <&ccu RST_BUS_UART0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		uart1: serial@5000400 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x05000400 0x400>;
>> +			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&ccu CLK_BUS_UART1>;
>> +			resets = <&ccu RST_BUS_UART1>;
>> +			status = "disabled";
>> +		};
>> +
>> +		uart2: serial@5000800 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x05000800 0x400>;
>> +			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&ccu CLK_BUS_UART2>;
>> +			resets = <&ccu RST_BUS_UART2>;
>> +			status = "disabled";
>> +		};
>> +
>> +		uart3: serial@5000c00 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x05000c00 0x400>;
>> +			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&ccu CLK_BUS_UART3>;
>> +			resets = <&ccu RST_BUS_UART3>;
>> +			status = "disabled";
>> +		};
>> +
>> +		uart4: serial@5001000 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x05001000 0x400>;
>> +			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&ccu CLK_BUS_UART4>;
>> +			resets = <&ccu RST_BUS_UART4>;
>> +			status = "disabled";
>> +		};
>> +
>> +		uart5: serial@5001400 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x05001400 0x400>;
>> +			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&ccu CLK_BUS_UART5>;
>> +			resets = <&ccu RST_BUS_UART5>;
>> +			status = "disabled";
>> +		};
>> +
>> +		i2c0: i2c@5002000 {
>> +			compatible = "allwinner,sun50i-h616-i2c",
>> +				     "allwinner,sun6i-a31-i2c";
>> +			reg = <0x05002000 0x400>;
>> +			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&ccu CLK_BUS_I2C0>;
>> +			resets = <&ccu RST_BUS_I2C0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&i2c0_pins>;
>> +			status = "disabled";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +		};
>> +
>> +		i2c1: i2c@5002400 {
>> +			compatible = "allwinner,sun50i-h616-i2c",
>> +				     "allwinner,sun6i-a31-i2c";
>> +			reg = <0x05002400 0x400>;
>> +			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&ccu CLK_BUS_I2C1>;
>> +			resets = <&ccu RST_BUS_I2C1>;
>> +			status = "disabled";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +		};
>> +
>> +		i2c2: i2c@5002800 {
>> +			compatible = "allwinner,sun50i-h616-i2c",
>> +				     "allwinner,sun6i-a31-i2c";
>> +			reg = <0x05002800 0x400>;
>> +			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&ccu CLK_BUS_I2C2>;
>> +			resets = <&ccu RST_BUS_I2C2>;
>> +			status = "disabled";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +		};
>> +
>> +		i2c3: i2c@5002c00 {
>> +			compatible = "allwinner,sun50i-h616-i2c",
>> +				     "allwinner,sun6i-a31-i2c";
>> +			reg = <0x05002c00 0x400>;
>> +			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&ccu CLK_BUS_I2C3>;
>> +			resets = <&ccu RST_BUS_I2C3>;
>> +			status = "disabled";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +		};
>> +
>> +		i2c4: i2c@5003000 {
>> +			compatible = "allwinner,sun50i-h616-i2c",
>> +				     "allwinner,sun6i-a31-i2c";
>> +			reg = <0x05003000 0x400>;
>> +			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&ccu CLK_BUS_I2C4>;
>> +			resets = <&ccu RST_BUS_I2C4>;
>> +			status = "disabled";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +		};
>> +
>> +		spi0: spi@5010000 {
>> +			compatible = "allwinner,sun50i-h616-spi",
>> +				     "allwinner,sun8i-h3-spi";
>> +			reg = <0x05010000 0x1000>;
>> +			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
>> +			clock-names = "ahb", "mod";
>> +			resets = <&ccu RST_BUS_SPI0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&spi0_pins>;
>> +			status = "disabled";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +		};
>> +
>> +		spi1: spi@5011000 {
>> +			compatible = "allwinner,sun50i-h616-spi",
>> +				     "allwinner,sun8i-h3-spi";
>> +			reg = <0x05011000 0x1000>;
>> +			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
>> +			clock-names = "ahb", "mod";
>> +			resets = <&ccu RST_BUS_SPI1>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&spi1_pins>;
>> +			status = "disabled";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +		};
>> +
>> +		emac0: ethernet@5020000 {
>> +			compatible = "allwinner,sun50i-h616-emac",
>> +				     "allwinner,sun50i-a64-emac";
>> +			syscon = <&syscon>;
>> +			reg = <0x05020000 0x10000>;
>> +			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
>> +			interrupt-names = "macirq";
>> +			resets = <&ccu RST_BUS_EMAC0>;
>> +			reset-names = "stmmaceth";
>> +			clocks = <&ccu CLK_BUS_EMAC0>;
>> +			clock-names = "stmmaceth";
>> +			status = "disabled";
>> +
>> +			mdio: mdio {
>> +				compatible = "snps,dwmac-mdio";
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +			};
>> +		};
>> +
>> +		usbotg: usb@5100000 {
>> +			compatible = "allwinner,sun50i-h616-musb",
>> +				     "allwinner,sun8i-a33-musb";
>> +			reg = <0x05100000 0x0400>;
>> +			clocks = <&ccu CLK_BUS_OTG>;
>> +			resets = <&ccu RST_BUS_OTG>;
>> +			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
>> +			interrupt-names = "mc";
>> +			phys = <&usbphy 0>;
>> +			phy-names = "usb";
>> +			extcon = <&usbphy 0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		usbphy: phy@5100400 {
>> +			compatible = "allwinner,sun50i-h616-usb-phy";
>> +			reg = <0x05100400 0x24>,
>> +			      <0x05101800 0x4>,
>> +			      <0x05200800 0x4>,
>> +			      <0x05310800 0x4>,
>> +			      <0x05311800 0x4>;
>> +			reg-names = "phy_ctrl",
>> +				    "pmu0",
>> +				    "pmu1",
>> +				    "pmu2",
>> +				    "pmu3";
>> +			clocks = <&ccu CLK_USB_PHY0>,
>> +				 <&ccu CLK_USB_PHY1>,
>> +				 <&ccu CLK_USB_PHY2>,
>> +				 <&ccu CLK_USB_PHY3>;
>> +			clock-names = "usb0_phy",
>> +				      "usb1_phy",
>> +				      "usb2_phy",
>> +				      "usb3_phy";
>> +			resets = <&ccu RST_USB_PHY0>,
>> +				 <&ccu RST_USB_PHY1>,
>> +				 <&ccu RST_USB_PHY2>,
>> +				 <&ccu RST_USB_PHY3>;
>> +			reset-names = "usb0_reset",
>> +				      "usb1_reset",
>> +				      "usb2_reset",
>> +				      "usb3_reset";
>> +			status = "disabled";
>> +			#phy-cells = <1>;
>> +		};
>
>Did you send a patch to support that PHY?
>
>Maxime

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel