[PATCH 0/3] EDAC: support for Armada 38x and 98dx3236 SoCs

[PATCH 0/3] EDAC: support for Armada 38x and 98dx3236 SoCs

[Chris Packham]

This series applies on top of Jan Lubbe's "EDAC drivers for Armada XP L2 and
DDR" series[1].

The Armada 38x as well as the 98dx3236 and similar switch chips with integrated
CPUs use the same SDRAM controller block as the Armada XP. The key difference
is the width of the DDR interface.

[1] - https://marc.info/?l=linux-edac&m=151030475715706&w=2

Chris Packham (3):
  ARM: dts: enable L2 cache parity and ecc on db-xc3-24g4xg board
  ARM: dts: mvebu: add sdram controller node to Armada-38x
  EDAC: armada_xp: Add support for more SoCs

 arch/arm/boot/dts/armada-38x.dtsi             | 5 +++++
 arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts | 5 +++++
 drivers/edac/armada_xp_edac.c                 | 5 +++++
 3 files changed, 15 insertions(+)

-- 
2.15.1

[PATCH 1/3] ARM: dts: enable L2 cache parity and ecc on db-xc3-24g4xg board

[Chris Packham]

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
 arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts b/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts
index 06fce35d7491..00ca489fc788 100644
--- a/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts
+++ b/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts
@@ -70,6 +70,11 @@
 	};
 };
 
+&L2 {
+	arm,parity-enable;
+	marvell,ecc-enable;
+};
+
 &devbus_bootcs {
 	status = "okay";
 
-- 
2.15.1

[PATCH 1/3] ARM: dts: enable L2 cache parity and ecc on db-xc3-24g4xg board

[Gregory CLEMENT]

Hi Chris,

 On mar., janv. 09 2018, Chris Packham <chris.packham@alliedtelesis.co.nz> wrote:

Could you have add a (even small) message in the commit log?

Also could you improve the title by specify that it applies on
armada-xp, like this:

ARM: dts: armada-xp: enable L2 cache parity and ecc on db-xc3-24g4xg


> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> ---
>  arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts | 5 +++++
>  1 file changed, 5 insertions(+)
>
> diff --git a/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts b/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts
> index 06fce35d7491..00ca489fc788 100644
> --- a/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts
> +++ b/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts
> @@ -70,6 +70,11 @@
>  	};
>  };
>  
> +&L2 {
> +	arm,parity-enable;
> +	marvell,ecc-enable;

It is not a problem for me to already applied the device tree change
even if the driver is not merged yet. But I would like to have an
acked-by on this new property by either a device tree maintainer or at
least the EDAC maintainer, of course having both acked-by would be
perfect ! :)

Thanks,

Gregory




> +};
> +
>  &devbus_bootcs {
>  	status = "okay";
>  
> -- 
> 2.15.1
>

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com

[PATCH 1/3] ARM: dts: enable L2 cache parity and ecc on db-xc3-24g4xg board

[Chris Packham]

Hi Gregory,

On 10/01/18 21:24, Gregory CLEMENT wrote:
> Hi Chris,
> 
>   On mar., janv. 09 2018, Chris Packham <chris.packham@alliedtelesis.co.nz> wrote:
> 
> Could you have add a (even small) message in the commit log?
> 
> Also could you improve the title by specify that it applies on
> armada-xp, like this:
> 
> ARM: dts: armada-xp: enable L2 cache parity and ecc on db-xc3-24g4xg
>

Will do.

>> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
>> ---
>>   arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts | 5 +++++
>>   1 file changed, 5 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts b/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts
>> index 06fce35d7491..00ca489fc788 100644
>> --- a/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts
>> +++ b/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts
>> @@ -70,6 +70,11 @@
>>   	};
>>   };
>>   
>> +&L2 {
>> +	arm,parity-enable;
>> +	marvell,ecc-enable;
> 
> It is not a problem for me to already applied the device tree change
> even if the driver is not merged yet. But I would like to have an
> acked-by on this new property by either a device tree maintainer or at
> least the EDAC maintainer, of course having both acked-by would be
> perfect ! :)

Thanks, I was hoping you would say that. That way I can keep this 
independent of the EDAC driver changes.

> 
> Thanks,
> 
> Gregory
> 
> 
> 
> 
>> +};
>> +
>>   &devbus_bootcs {
>>   	status = "okay";
>>   
>> -- 
>> 2.15.1
>>
> 

[PATCH 2/3] ARM: dts: mvebu: add sdram controller node to Armada-38x

[Chris Packham]

The Armada-38x uses an SDRAM controller that is compatible with the
Armada-XP. The key difference is the width of the bus (XP is 64/32, 38x
is 32/16). The SDRAM controller registers are the same between the two
SoCs.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
 arch/arm/boot/dts/armada-38x.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi
index 00ff549d4e39..6d34c5ec178f 100644
--- a/arch/arm/boot/dts/armada-38x.dtsi
+++ b/arch/arm/boot/dts/armada-38x.dtsi
@@ -138,6 +138,11 @@
 			#size-cells = <1>;
 			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
 
+			sdramc at 1400 {
+				compatible = "marvell,armada-xp-sdram-controller";
+				reg = <0x1400 0x500>;
+			};
+
 			L2: cache-controller at 8000 {
 				compatible = "arm,pl310-cache";
 				reg = <0x8000 0x1000>;
-- 
2.15.1

[PATCH 2/3] ARM: dts: mvebu: add sdram controller node to Armada-38x

[Gregory CLEMENT]

Hi Chris,
 
 On mar., janv. 09 2018, Chris Packham <chris.packham@alliedtelesis.co.nz> wrote:

> The Armada-38x uses an SDRAM controller that is compatible with the
> Armada-XP. The key difference is the width of the bus (XP is 64/32, 38x
> is 32/16). The SDRAM controller registers are the same between the two
> SoCs.
>
> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> ---
>  arch/arm/boot/dts/armada-38x.dtsi | 5 +++++
>  1 file changed, 5 insertions(+)
>
> diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi
> index 00ff549d4e39..6d34c5ec178f 100644
> --- a/arch/arm/boot/dts/armada-38x.dtsi
> +++ b/arch/arm/boot/dts/armada-38x.dtsi
> @@ -138,6 +138,11 @@
>  			#size-cells = <1>;
>  			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
>  
> +			sdramc at 1400 {

Could you add a label? Thanks to this it would be possible to
enable/disable it at board level in a esay way.

> +				compatible = "marvell,armada-xp-sdram-controller";
> +				reg = <0x1400 0x500>;

What about adding status = "disabled" ?

Thanks to this we can enable it at board level only if we really want
it, it would avoid nasty regression on boards that don't need it, if an
issue occurs. Unless you are sure that it is completely safe to enable
it for everyone.

Thanks,

Gregory


> +			};
> +
>  			L2: cache-controller at 8000 {
>  				compatible = "arm,pl310-cache";
>  				reg = <0x8000 0x1000>;
> -- 
> 2.15.1
>

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com

[PATCH 2/3] ARM: dts: mvebu: add sdram controller node to Armada-38x

[Chris Packham]

On 10/01/18 21:31, Gregory CLEMENT wrote:
> Hi Chris,
>   
>   On mar., janv. 09 2018, Chris Packham <chris.packham@alliedtelesis.co.nz> wrote:
> 
>> The Armada-38x uses an SDRAM controller that is compatible with the
>> Armada-XP. The key difference is the width of the bus (XP is 64/32, 38x
>> is 32/16). The SDRAM controller registers are the same between the two
>> SoCs.
>>
>> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
>> ---
>>   arch/arm/boot/dts/armada-38x.dtsi | 5 +++++
>>   1 file changed, 5 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi
>> index 00ff549d4e39..6d34c5ec178f 100644
>> --- a/arch/arm/boot/dts/armada-38x.dtsi
>> +++ b/arch/arm/boot/dts/armada-38x.dtsi
>> @@ -138,6 +138,11 @@
>>   			#size-cells = <1>;
>>   			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
>>   
>> +			sdramc at 1400 {
> 
> Could you add a label? Thanks to this it would be possible to
> enable/disable it at board level in a esay way.
> 

Sure. Any suggestions for a name better than "sdramc:"?

It's probably worth adding the same label to armada-xp.dtsi and 
armada-xp-98dx3236.dtsi.

>> +				compatible = "marvell,armada-xp-sdram-controller";
>> +				reg = <0x1400 0x500>;
> 
> What about adding status = "disabled" ?
> 
> Thanks to this we can enable it at board level only if we really want
> it, it would avoid nasty regression on boards that don't need it, if an
> issue occurs. Unless you are sure that it is completely safe to enable
> it for everyone.

The EDAC driver (which is default n) will not probe the device if ECC 
has not been enabled so that should be safe.

Other than the EDAC driver the only other code that looks at this is in 
arch/arm/mach-mvebu/pm.c and it almost seems like an omission that this 
code is not active on armada-38x. The armada-38x platforms I have access 
to don't use suspend/resume so I can't verify this.

[PATCH 2/3] ARM: dts: mvebu: add sdram controller node to Armada-38x

[Gregory CLEMENT]

Hi Chris,
 
 On mer., janv. 10 2018, Chris Packham <Chris.Packham@alliedtelesis.co.nz> wrote:

> On 10/01/18 21:31, Gregory CLEMENT wrote:
>> Hi Chris,
>>   
>>   On mar., janv. 09 2018, Chris Packham <chris.packham@alliedtelesis.co.nz> wrote:
>> 
>>> The Armada-38x uses an SDRAM controller that is compatible with the
>>> Armada-XP. The key difference is the width of the bus (XP is 64/32, 38x
>>> is 32/16). The SDRAM controller registers are the same between the two
>>> SoCs.
>>>
>>> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
>>> ---
>>>   arch/arm/boot/dts/armada-38x.dtsi | 5 +++++
>>>   1 file changed, 5 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi
>>> index 00ff549d4e39..6d34c5ec178f 100644
>>> --- a/arch/arm/boot/dts/armada-38x.dtsi
>>> +++ b/arch/arm/boot/dts/armada-38x.dtsi
>>> @@ -138,6 +138,11 @@
>>>   			#size-cells = <1>;
>>>   			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
>>>   
>>> +			sdramc at 1400 {
>> 
>> Could you add a label? Thanks to this it would be possible to
>> enable/disable it at board level in a esay way.
>> 
>
> Sure. Any suggestions for a name better than "sdramc:"?

For me sdramc: is fine.

>
> It's probably worth adding the same label to armada-xp.dtsi and 
> armada-xp-98dx3236.dtsi.

Right.

>
>>> +				compatible = "marvell,armada-xp-sdram-controller";
>>> +				reg = <0x1400 0x500>;
>> 
>> What about adding status = "disabled" ?
>> 
>> Thanks to this we can enable it at board level only if we really want
>> it, it would avoid nasty regression on boards that don't need it, if an
>> issue occurs. Unless you are sure that it is completely safe to enable
>> it for everyone.
>
> The EDAC driver (which is default n) will not probe the device if ECC 
> has not been enabled so that should be safe.

OK in this case no need to disable it by default.

Thanks,

Gregory

>
> Other than the EDAC driver the only other code that looks at this is in 
> arch/arm/mach-mvebu/pm.c and it almost seems like an omission that this 
> code is not active on armada-38x. The armada-38x platforms I have access 
> to don't use suspend/resume so I can't verify this.
>

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com

[PATCH 3/3] EDAC: armada_xp: Add support for more SoCs

[Chris Packham]

The Armada 38x and other integrated SoCs use a reduced pin count so the
width of the SDRAM interface is smaller than the Armada XP SoCs. This
means that the definition of "full" and "half" width is reduced from
64/32 to 32/16.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
 drivers/edac/armada_xp_edac.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/edac/armada_xp_edac.c b/drivers/edac/armada_xp_edac.c
index cb9173b30aa9..40cef261e61b 100644
--- a/drivers/edac/armada_xp_edac.c
+++ b/drivers/edac/armada_xp_edac.c
@@ -347,6 +347,11 @@ static int armada_xp_mc_edac_probe(struct platform_device *pdev)
 
 	armada_xp_mc_edac_read_config(mci);
 
+	/* These SoCs have a reduced width bus */
+	if (of_machine_is_compatible("marvell,armada380") ||
+	    of_machine_is_compatible("marvell,armadaxp-98dx3236"))
+		drvdata->width /= 2;
+
 	/* configure SBE threshold */
 	/* it seems that SBEs are not captured otherwise */
 	writel(1 << SDRAM_ERR_CTRL_ERR_THR_OFFSET,
-- 
2.15.1

[PATCH 0/3] ARM: dts: SDRAM and L2 cache EDAC for Armada SoCs

[Chris Packham]

This series was waiting for the armada_xp edac driver to be accepted.
Now that it has the relevant nodes can be added to the Armada SoCs. So
that boards can use the EDAC driver if they have the hardware support.

The db-xc3-24g4xg.dts board doesn't have an ECC chip for it's DDR but it
can use the L2 cache parity and ecc support.

Chris Packham (3):
  ARM: dts: armada-xp: enable L2 cache parity and ecc on db-xc3-24g4xg
  ARM: dts: mvebu: add sdram controller node to Armada-38x
  ARM: dts: armada-xp: add label to sdram-controller node

 arch/arm/boot/dts/armada-38x.dtsi             | 5 +++++
 arch/arm/boot/dts/armada-xp-98dx3236.dtsi     | 2 +-
 arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts | 5 +++++
 arch/arm/boot/dts/armada-xp.dtsi              | 2 +-
 4 files changed, 12 insertions(+), 2 deletions(-)

-- 
2.23.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/3] ARM: dts: mvebu: add sdram controller node to Armada-38x

[Chris Packham]

The Armada-38x uses an SDRAM controller that is compatible with the
Armada-XP. The key difference is the width of the bus (XP is 64/32, 38x
is 32/16). The SDRAM controller registers are the same between the two
SoCs.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
 arch/arm/boot/dts/armada-38x.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi
index 3f4bb44d85f0..e038abc0c6b4 100644
--- a/arch/arm/boot/dts/armada-38x.dtsi
+++ b/arch/arm/boot/dts/armada-38x.dtsi
@@ -103,6 +103,11 @@
 			#size-cells = <1>;
 			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
 
+			sdramc: sdramc@1400 {
+				compatible = "marvell,armada-xp-sdram-controller";
+				reg = <0x1400 0x500>;
+			};
+
 			L2: cache-controller@8000 {
 				compatible = "arm,pl310-cache";
 				reg = <0x8000 0x1000>;
-- 
2.23.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel