[PATCH 00/10] ux500: support for snowball board.

[PATCH 00/10] ux500: support for snowball board.

[mathieu.poirier at linaro.org]

From: Mathieu J. Poirier <mathieu.poirier@linaro.org>

This suite of patches introduce support for the u8500 based
snowball board.

Alessandro Rubini (3):
  smsc911x: use shifted register access
  ux500: added snowball-netev with latest fixes
  ux500: added snowball-digio.c

Mathieu J. Poirier (7):
  ux500: Introducing foundation for snowball board.
  ux500: Adding new board files for snowball.
  ux500: Adding custom pin configuration file for snowball. - Adding
    dependency in Makefile. - Adding init function call to
    board-snowball.c - New header file.
  ux500: Adding sdi support on snowball.
  ux500: hooking up netdev and digio to compilation.
  ux500: Addressing irq header file dependency for snowball.
  ux500: adding config file options for snowball board.

 arch/arm/configs/u8500_defconfig              | 1497 +++++++++++++++++++++++++
 arch/arm/mach-ux500/Kconfig                   |    6 +
 arch/arm/mach-ux500/Makefile                  |    5 +
 arch/arm/mach-ux500/board-mop500-sdi.c        |   32 +-
 arch/arm/mach-ux500/board-mop500.h            |    5 +
 arch/arm/mach-ux500/board-snowball-digio.c    |  122 ++
 arch/arm/mach-ux500/board-snowball-netdev.c   |   86 ++
 arch/arm/mach-ux500/board-snowball-pins.c     |  133 +++
 arch/arm/mach-ux500/board-snowball.c          |  265 +++++
 arch/arm/mach-ux500/board-snowball.h          |   18 +
 arch/arm/mach-ux500/include/mach/irqs.h       |    2 +-
 arch/arm/mach-ux500/include/mach/uncompress.h |    3 +-
 arch/arm/tools/mach-types                     |    1 +
 drivers/net/smsc911x.c                        |   27 +-
 include/linux/smsc911x.h                      |    1 +
 15 files changed, 2185 insertions(+), 18 deletions(-)
 create mode 100644 arch/arm/mach-ux500/board-snowball-digio.c
 create mode 100644 arch/arm/mach-ux500/board-snowball-netdev.c
 create mode 100644 arch/arm/mach-ux500/board-snowball-pins.c
 create mode 100644 arch/arm/mach-ux500/board-snowball.c
 create mode 100644 arch/arm/mach-ux500/board-snowball.h

[PATCH 01/10] ux500: Introducing foundation for snowball board.

[mathieu.poirier at linaro.org]

From: Mathieu J. Poirier <mathieu.poirier@linaro.org>

Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
---
 arch/arm/mach-ux500/Kconfig                   |    6 ++++++
 arch/arm/mach-ux500/include/mach/uncompress.h |    3 ++-
 arch/arm/tools/mach-types                     |    1 +
 3 files changed, 9 insertions(+), 1 deletions(-)

diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig
index 7f8620f..ba5c270 100644
--- a/arch/arm/mach-ux500/Kconfig
+++ b/arch/arm/mach-ux500/Kconfig
@@ -26,6 +26,12 @@ config MACH_U8500
 	help
 	  Include support for the mop500 development platform.
 
+config MACH_U8500_SNOWBALL
+	bool "U8500 Snowball platform"
+	depends on UX500_SOC_DB8500
+	help
+	  Include support for the snowball development platform.
+
 config MACH_U5500
 	bool "U5500 Development platform"
 	depends on UX500_SOC_DB5500
diff --git a/arch/arm/mach-ux500/include/mach/uncompress.h b/arch/arm/mach-ux500/include/mach/uncompress.h
index ab0fe14..3b4f6b7 100644
--- a/arch/arm/mach-ux500/include/mach/uncompress.h
+++ b/arch/arm/mach-ux500/include/mach/uncompress.h
@@ -54,7 +54,8 @@ static inline void arch_decomp_setup(void)
 	if (machine_is_u8500() ||
 	    machine_is_svp8500v1() ||
 	    machine_is_svp8500v2() ||
-	    machine_is_hrefv60())
+	    machine_is_hrefv60()   ||
+	    machine_is_snowball())
 		ux500_uart_base = U8500_UART2_BASE;
 	else if (machine_is_u5500())
 		ux500_uart_base = U5500_UART0_BASE;
diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types
index 9d6feaa..e9f780e 100644
--- a/arch/arm/tools/mach-types
+++ b/arch/arm/tools/mach-types
@@ -3316,3 +3316,4 @@ rover_g8		MACH_ROVER_G8		ROVER_G8		3335
 t5388p			MACH_T5388P		T5388P			3336
 dingo			MACH_DINGO		DINGO			3337
 goflexhome		MACH_GOFLEXHOME		GOFLEXHOME		3338
+snowball		MACH_U8500_SNOWBALL	SNOWBALL		3363
-- 
1.7.1

[PATCH 02/10] ux500: Adding new board files for snowball.

[mathieu.poirier at linaro.org]

From: Mathieu J. Poirier <mathieu.poirier@linaro.org>

Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
---
 arch/arm/mach-ux500/Makefile         |    2 +
 arch/arm/mach-ux500/board-snowball.c |  262 ++++++++++++++++++++++++++++++++++
 2 files changed, 264 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-ux500/board-snowball.c

diff --git a/arch/arm/mach-ux500/Makefile b/arch/arm/mach-ux500/Makefile
index b549a8f..60c26c6 100644
--- a/arch/arm/mach-ux500/Makefile
+++ b/arch/arm/mach-ux500/Makefile
@@ -11,6 +11,8 @@ obj-$(CONFIG_MACH_U8500)	+= board-mop500.o board-mop500-sdi.o \
 				board-mop500-uib.o board-mop500-stuib.o \
 				board-mop500-u8500uib.o \
 				board-mop500-pins.o
+obj-$(CONFIG_MACH_U8500_SNOWBALL) += board-snowball.o \
+				board-mop500-regulators.o
 obj-$(CONFIG_MACH_U5500)	+= board-u5500.o board-u5500-sdi.o
 obj-$(CONFIG_SMP)		+= platsmp.o headsmp.o
 obj-$(CONFIG_HOTPLUG_CPU)	+= hotplug.o
diff --git a/arch/arm/mach-ux500/board-snowball.c b/arch/arm/mach-ux500/board-snowball.c
new file mode 100644
index 0000000..620f132
--- /dev/null
+++ b/arch/arm/mach-ux500/board-snowball.c
@@ -0,0 +1,262 @@
+/*
+ * Copyright (C) 2010-2011 ST-Ericsson
+ *
+ * Author: Mathieu Poirier <mathieu.poirier@linaro.org>, based on
+ *         the work of Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/i2c.h>
+#include <linux/gpio.h>
+#include <linux/amba/bus.h>
+#include <linux/amba/pl022.h>
+#include <linux/amba/serial.h>
+#include <linux/spi/spi.h>
+#include <linux/mfd/ab8500.h>
+#include <linux/input.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <plat/i2c.h>
+#include <plat/ste_dma40.h>
+
+#include <mach/hardware.h>
+#include <mach/setup.h>
+#include <mach/devices.h>
+#include <mach/irqs.h>
+
+#include "ste-dma40-db8500.h"
+#include "devices-db8500.h"
+#include "board-mop500.h"
+#include "board-mop500-regulators.h"
+
+static struct ab8500_platform_data ab8500_platdata = {
+	.irq_base	= MOP500_AB8500_IRQ_BASE,
+	.regulator	= ab8500_regulators,
+	.num_regulator	= ARRAY_SIZE(ab8500_regulators),
+};
+
+static struct resource ab8500_resources[] = {
+	[0] = {
+		.start	= IRQ_DB8500_AB8500,
+		.end	= IRQ_DB8500_AB8500,
+		.flags	= IORESOURCE_IRQ
+	}
+};
+
+struct platform_device ab8500_device_snowball = {
+	.name = "ab8500-i2c",
+	.id = 0,
+	.dev = {
+		.platform_data = &ab8500_platdata,
+	},
+	.num_resources = 1,
+	.resource = ab8500_resources,
+};
+
+static struct i2c_board_info mop500_i2c0_devices[] = {};
+static struct i2c_board_info mop500_i2c2_devices[] = {};
+
+#define U8500_I2C_CONTROLLER(id, _slsu, _tft, _rft, clk, _sm) \
+static struct nmk_i2c_controller u8500_i2c##id##_data = { \
+	/*				\
+	 * slave data setup time, which is	\
+	 * 250 ns,100ns,10ns which is 14,6,2	\
+	 * respectively for a 48 Mhz	\
+	 * i2c clock			\
+	 */				\
+	.slsu		= _slsu,	\
+	/* Tx FIFO threshold */		\
+	.tft		= _tft,		\
+	/* Rx FIFO threshold */		\
+	.rft		= _rft,		\
+	/* std. mode operation */	\
+	.clk_freq	= clk,		\
+	.sm		= _sm,		\
+}
+
+/*
+ * The board uses 4 i2c controllers, initialize all of
+ * them with slave data setup time of 250 ns,
+ * Tx & Rx FIFO threshold values as 1 and standard
+ * mode of operation
+ */
+U8500_I2C_CONTROLLER(0, 0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD);
+U8500_I2C_CONTROLLER(1, 0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD);
+U8500_I2C_CONTROLLER(2,	0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD);
+U8500_I2C_CONTROLLER(3,	0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD);
+
+static void __init mop500_i2c_init(void)
+{
+	db8500_add_i2c0(&u8500_i2c0_data);
+	db8500_add_i2c1(&u8500_i2c1_data);
+	db8500_add_i2c2(&u8500_i2c2_data);
+	db8500_add_i2c3(&u8500_i2c3_data);
+}
+
+/* add any platform devices here - TODO */
+static struct platform_device *platform_devs[] __initdata = {};
+
+#ifdef CONFIG_STE_DMA40
+static struct stedma40_chan_cfg ssp0_dma_cfg_rx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+	.src_dev_type =  DB8500_DMA_DEV8_SSP0_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg ssp0_dma_cfg_tx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+	.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV8_SSP0_TX,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+#endif
+
+static struct pl022_ssp_controller ssp0_platform_data = {
+	.bus_id = 0,
+#ifdef CONFIG_STE_DMA40
+	.enable_dma = 1,
+	.dma_filter = stedma40_filter,
+	.dma_rx_param = &ssp0_dma_cfg_rx,
+	.dma_tx_param = &ssp0_dma_cfg_tx,
+#else
+	.enable_dma = 0,
+#endif
+	/* on this platform, gpio 31,142,144,214 &
+	 * 224 are connected as chip selects
+	 */
+	.num_chipselect = 5,
+};
+
+static void __init mop500_spi_init(void)
+{
+	db8500_add_ssp0(&ssp0_platform_data);
+}
+
+#ifdef CONFIG_STE_DMA40
+static struct stedma40_chan_cfg uart0_dma_cfg_rx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+	.src_dev_type =  DB8500_DMA_DEV13_UART0_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart0_dma_cfg_tx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+	.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV13_UART0_TX,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart1_dma_cfg_rx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+	.src_dev_type =  DB8500_DMA_DEV12_UART1_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart1_dma_cfg_tx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+	.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV12_UART1_TX,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart2_dma_cfg_rx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+	.src_dev_type =  DB8500_DMA_DEV11_UART2_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart2_dma_cfg_tx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+	.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV11_UART2_TX,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+#endif
+
+static struct amba_pl011_data uart0_plat = {
+#ifdef CONFIG_STE_DMA40
+	.dma_filter = stedma40_filter,
+	.dma_rx_param = &uart0_dma_cfg_rx,
+	.dma_tx_param = &uart0_dma_cfg_tx,
+#endif
+};
+
+static struct amba_pl011_data uart1_plat = {
+#ifdef CONFIG_STE_DMA40
+	.dma_filter = stedma40_filter,
+	.dma_rx_param = &uart1_dma_cfg_rx,
+	.dma_tx_param = &uart1_dma_cfg_tx,
+#endif
+};
+
+static struct amba_pl011_data uart2_plat = {
+#ifdef CONFIG_STE_DMA40
+	.dma_filter = stedma40_filter,
+	.dma_rx_param = &uart2_dma_cfg_rx,
+	.dma_tx_param = &uart2_dma_cfg_tx,
+#endif
+};
+
+static void __init mop500_uart_init(void)
+{
+	db8500_add_uart0(&uart0_plat);
+	db8500_add_uart1(&uart1_plat);
+	db8500_add_uart2(&uart2_plat);
+}
+
+static void __init mop500_init_machine(void)
+{
+	u8500_init_devices();
+
+	platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
+
+	mop500_i2c_init();
+	mop500_spi_init();
+	mop500_uart_init();
+
+	platform_device_register(&ab8500_device_snowball);
+
+	i2c_register_board_info(0, mop500_i2c0_devices,
+				ARRAY_SIZE(mop500_i2c0_devices));
+	i2c_register_board_info(2, mop500_i2c2_devices,
+				ARRAY_SIZE(mop500_i2c2_devices));
+}
+
+MACHINE_START(SNOWBALL, "Calao Systems Snowball platform")
+	.boot_params	= 0x100,
+	.map_io		= u8500_map_io,
+	.init_irq	= ux500_init_irq,
+	/* we re-use nomadik timer here */
+	.timer		= &ux500_timer,
+	.init_machine	= mop500_init_machine,
+MACHINE_END
-- 
1.7.1

[PATCH 03/10] ux500: Adding custom pin configuration file for snowball. - Adding dependency in Makefile. - Adding init function call to board-snowball.c - New header file.

[mathieu.poirier at linaro.org]

From: Mathieu J. Poirier <mathieu.poirier@linaro.org>

Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
---
 arch/arm/mach-ux500/Makefile              |    1 +
 arch/arm/mach-ux500/board-snowball-pins.c |  133 +++++++++++++++++++++++++++++
 arch/arm/mach-ux500/board-snowball.c      |    4 +-
 arch/arm/mach-ux500/board-snowball.h      |   18 ++++
 4 files changed, 155 insertions(+), 1 deletions(-)
 create mode 100644 arch/arm/mach-ux500/board-snowball-pins.c
 create mode 100644 arch/arm/mach-ux500/board-snowball.h

diff --git a/arch/arm/mach-ux500/Makefile b/arch/arm/mach-ux500/Makefile
index 60c26c6..d74f303 100644
--- a/arch/arm/mach-ux500/Makefile
+++ b/arch/arm/mach-ux500/Makefile
@@ -12,6 +12,7 @@ obj-$(CONFIG_MACH_U8500)	+= board-mop500.o board-mop500-sdi.o \
 				board-mop500-u8500uib.o \
 				board-mop500-pins.o
 obj-$(CONFIG_MACH_U8500_SNOWBALL) += board-snowball.o \
+				board-snowball-pins.o \
 				board-mop500-regulators.o
 obj-$(CONFIG_MACH_U5500)	+= board-u5500.o board-u5500-sdi.o
 obj-$(CONFIG_SMP)		+= platsmp.o headsmp.o
diff --git a/arch/arm/mach-ux500/board-snowball-pins.c b/arch/arm/mach-ux500/board-snowball-pins.c
new file mode 100644
index 0000000..216fd50
--- /dev/null
+++ b/arch/arm/mach-ux500/board-snowball-pins.c
@@ -0,0 +1,133 @@
+/*
+ * Copyright (C) 2011-2012 ST-Ericsson
+ *
+ * Author: Mathieu Poirier <mathieu.poirier@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+
+#include <plat/pincfg.h>
+
+#include <mach/hardware.h>
+
+#include "pins-db8500.h"
+
+static pin_cfg_t snowball_pins[] = {
+	/* I2C */
+	GPIO147_I2C0_SCL,
+	GPIO148_I2C0_SDA,
+	GPIO16_I2C1_SCL,
+	GPIO17_I2C1_SDA,
+	GPIO10_I2C2_SDA,
+	GPIO11_I2C2_SCL,
+	GPIO229_I2C3_SDA,
+	GPIO230_I2C3_SCL,
+
+        /* SSP0, to AB8500 */
+	GPIO143_SSP0_CLK,
+	GPIO144_SSP0_FRM,
+	GPIO145_SSP0_RXD	| PIN_PULL_DOWN,
+	GPIO146_SSP0_TXD,
+
+	/* MSP0: BT */
+	GPIO12_MSP0_TXD,
+	GPIO13_MSP0_TFS,
+	GPIO14_MSP0_TCK,
+	GPIO15_MSP0_RXD,
+
+	/* MSP2: HDMI */
+	GPIO193_MSP2_TXD,
+	GPIO194_MSP2_TCK,
+	GPIO195_MSP2_TFS,
+	GPIO196_MSP2_RXD	| PIN_OUTPUT_LOW,
+
+	/* MMC0: MicroSD card */
+	GPIO18_MC0_CMDDIR	| PIN_OUTPUT_HIGH,
+	GPIO19_MC0_DAT0DIR	| PIN_OUTPUT_HIGH,
+	GPIO20_MC0_DAT2DIR	| PIN_OUTPUT_HIGH,
+	GPIO21_MC0_DAT31DIR	| PIN_OUTPUT_HIGH,
+	GPIO22_MC0_FBCLK	| PIN_INPUT_NOPULL,
+	GPIO23_MC0_CLK		| PIN_OUTPUT_LOW,
+	GPIO24_MC0_CMD		| PIN_INPUT_PULLUP,
+	GPIO25_MC0_DAT0		| PIN_INPUT_PULLUP,
+	GPIO26_MC0_DAT1		| PIN_INPUT_PULLUP,
+	GPIO27_MC0_DAT2		| PIN_INPUT_PULLUP,
+	GPIO28_MC0_DAT3		| PIN_INPUT_PULLUP,
+
+	/* SDI1: WLAN */
+	GPIO208_MC1_CLK		| PIN_OUTPUT_LOW,
+	GPIO209_MC1_FBCLK	| PIN_INPUT_NOPULL,
+	GPIO210_MC1_CMD		| PIN_INPUT_PULLUP,
+	GPIO211_MC1_DAT0	| PIN_INPUT_PULLUP,
+	GPIO212_MC1_DAT1	| PIN_INPUT_PULLUP,
+	GPIO213_MC1_DAT2	| PIN_INPUT_PULLUP,
+	GPIO214_MC1_DAT3	| PIN_INPUT_PULLUP,
+
+	/* MMC2: LAN */
+	GPIO86_SM_ADQ0,
+	GPIO87_SM_ADQ1,
+	GPIO88_SM_ADQ2,
+	GPIO89_SM_ADQ3,
+	GPIO90_SM_ADQ4,
+	GPIO91_SM_ADQ5,
+	GPIO92_SM_ADQ6,
+	GPIO93_SM_ADQ7,
+
+	GPIO94_SM_ADVn,
+	GPIO95_SM_CS0n,
+	GPIO96_SM_OEn,
+	GPIO97_SM_WEn,
+
+	GPIO128_SM_CKO,
+	GPIO130_SM_FBCLK,
+	GPIO131_SM_ADQ8,
+	GPIO132_SM_ADQ9,
+	GPIO133_SM_ADQ10,
+	GPIO134_SM_ADQ11,
+	GPIO135_SM_ADQ12,
+	GPIO136_SM_ADQ13,
+	GPIO137_SM_ADQ14,
+	GPIO138_SM_ADQ15,
+
+	/* RSTn_LAN */
+	GPIO141_GPIO		| PIN_OUTPUT_HIGH,
+
+	/* MMC4: eMMC */
+	GPIO197_MC4_DAT3	| PIN_INPUT_PULLUP,
+	GPIO198_MC4_DAT2	| PIN_INPUT_PULLUP,
+	GPIO199_MC4_DAT1	| PIN_INPUT_PULLUP,
+	GPIO200_MC4_DAT0	| PIN_INPUT_PULLUP,
+	GPIO201_MC4_CMD		| PIN_INPUT_PULLUP,
+	GPIO202_MC4_FBCLK	| PIN_INPUT_NOPULL,
+	GPIO203_MC4_CLK		| PIN_OUTPUT_LOW,
+	GPIO204_MC4_DAT7	| PIN_INPUT_PULLUP,
+	GPIO205_MC4_DAT6	| PIN_INPUT_PULLUP,
+	GPIO206_MC4_DAT5	| PIN_INPUT_PULLUP,
+	GPIO207_MC4_DAT4	| PIN_INPUT_PULLUP,
+
+	GPIO141_GPIO		| PIN_OUTPUT_HIGH, /* RSTn_LAN */
+
+	/* UART: WLAN */
+	GPIO0_U0_CTSn	| PIN_INPUT_PULLUP,
+	GPIO1_U0_RTSn	| PIN_OUTPUT_HIGH,
+	GPIO2_U0_RXD	| PIN_INPUT_PULLUP,
+	GPIO3_U0_TXD	| PIN_OUTPUT_HIGH,
+
+	/* UART: DBG port */
+	GPIO29_U2_RXD	| PIN_INPUT_PULLUP,
+	GPIO30_U2_TXD	| PIN_OUTPUT_HIGH,
+	GPIO31_U2_CTSn	| PIN_INPUT_PULLUP,
+	GPIO32_U2_RTSn	| PIN_OUTPUT_HIGH,
+};
+
+void __init snowball_pins_init(void)
+{
+	nmk_config_pins(snowball_pins,
+				ARRAY_SIZE(snowball_pins));
+}
diff --git a/arch/arm/mach-ux500/board-snowball.c b/arch/arm/mach-ux500/board-snowball.c
index 620f132..3b351ef 100644
--- a/arch/arm/mach-ux500/board-snowball.c
+++ b/arch/arm/mach-ux500/board-snowball.c
@@ -36,7 +36,7 @@
 
 #include "ste-dma40-db8500.h"
 #include "devices-db8500.h"
-#include "board-mop500.h"
+#include "board-snowball.h"
 #include "board-mop500-regulators.h"
 
 static struct ab8500_platform_data ab8500_platdata = {
@@ -238,6 +238,8 @@ static void __init mop500_init_machine(void)
 {
 	u8500_init_devices();
 
+	snowball_pins_init();
+
 	platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
 
 	mop500_i2c_init();
diff --git a/arch/arm/mach-ux500/board-snowball.h b/arch/arm/mach-ux500/board-snowball.h
new file mode 100644
index 0000000..fe08f7e
--- /dev/null
+++ b/arch/arm/mach-ux500/board-snowball.h
@@ -0,0 +1,18 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#ifndef __BOARD_SNOWBALL_H
+#define __BOARD_SNOWBALL_H
+
+struct i2c_board_info;
+
+extern void mop500_sdi_init(void);
+void __init snowball_pins_init(void);
+
+void mop500_uib_i2c_add(int busnum, struct i2c_board_info *info,
+		unsigned n);
+
+#endif
-- 
1.7.1

[PATCH 04/10] ux500: Adding sdi support on snowball.

[mathieu.poirier at linaro.org]

From: Mathieu J. Poirier <mathieu.poirier@linaro.org>

Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
---
 arch/arm/mach-ux500/Makefile           |    2 +-
 arch/arm/mach-ux500/board-mop500-sdi.c |   32 +++++++++++++++++++++++++-------
 arch/arm/mach-ux500/board-mop500.h     |    5 +++++
 arch/arm/mach-ux500/board-snowball.c   |    3 ++-
 4 files changed, 33 insertions(+), 9 deletions(-)

diff --git a/arch/arm/mach-ux500/Makefile b/arch/arm/mach-ux500/Makefile
index d74f303..016cb9f 100644
--- a/arch/arm/mach-ux500/Makefile
+++ b/arch/arm/mach-ux500/Makefile
@@ -13,7 +13,7 @@ obj-$(CONFIG_MACH_U8500)	+= board-mop500.o board-mop500-sdi.o \
 				board-mop500-pins.o
 obj-$(CONFIG_MACH_U8500_SNOWBALL) += board-snowball.o \
 				board-snowball-pins.o \
-				board-mop500-regulators.o
+				board-mop500-regulators.o board-mop500-sdi.o
 obj-$(CONFIG_MACH_U5500)	+= board-u5500.o board-u5500-sdi.o
 obj-$(CONFIG_SMP)		+= platsmp.o headsmp.o
 obj-$(CONFIG_HOTPLUG_CPU)	+= hotplug.o
diff --git a/arch/arm/mach-ux500/board-mop500-sdi.c b/arch/arm/mach-ux500/board-mop500-sdi.c
index bf0b024..d388f5e 100644
--- a/arch/arm/mach-ux500/board-mop500-sdi.c
+++ b/arch/arm/mach-ux500/board-mop500-sdi.c
@@ -35,10 +35,17 @@
 static u32 mop500_sdi0_vdd_handler(struct device *dev, unsigned int vdd,
 				   unsigned char power_mode)
 {
+	int gpio;
+
+	if (!machine_is_snowball())
+		gpio = GPIO_SDMMC_EN;
+	else
+		gpio = SNOWBALL_SDMMC_EN_GPIO;
+
 	if (power_mode == MMC_POWER_UP)
-		gpio_set_value_cansleep(GPIO_SDMMC_EN, 1);
+		gpio_set_value_cansleep(gpio, 1);
 	else if (power_mode == MMC_POWER_OFF)
-		gpio_set_value_cansleep(GPIO_SDMMC_EN, 0);
+		gpio_set_value_cansleep(gpio, 0);
 
 	return MCI_FBCLKEN | MCI_CMDDIREN | MCI_DATA0DIREN |
 	       MCI_DATA2DIREN | MCI_DATA31DIREN;
@@ -191,17 +198,28 @@ void __init mop500_sdi_init(void)
 	/* PoP:ed eMMC on top of DB8500 v1.0 has problems with high speed */
 	if (!cpu_is_u8500v10())
 		mop500_sdi2_data.capabilities |= MMC_CAP_MMC_HIGHSPEED;
-	db8500_add_sdi2(&mop500_sdi2_data);
+
+	/* sdi2 on snowball is in ATL_B mode for FSMC (LAN) */
+	if (!machine_is_snowball())
+		db8500_add_sdi2(&mop500_sdi2_data);
 
 	/* On-board eMMC */
 	db8500_add_sdi4(&mop500_sdi4_data);
 
-	if (machine_is_hrefv60()) {
-		mop500_sdi0_data.gpio_cd = HREFV60_SDMMC_CD_GPIO;
-		sdi0_en = HREFV60_SDMMC_EN_GPIO;
-		sdi0_vsel = HREFV60_SDMMC_1V8_3V_GPIO;
+	if (machine_is_hrefv60() || machine_is_snowball()) {
+		if (machine_is_hrefv60()) {
+			mop500_sdi0_data.gpio_cd = HREFV60_SDMMC_CD_GPIO;
+			sdi0_en = HREFV60_SDMMC_EN_GPIO;
+			sdi0_vsel = HREFV60_SDMMC_1V8_3V_GPIO;
+		} else if (machine_is_snowball()) {
+			mop500_sdi0_data.gpio_cd = SNOWBALL_SDMMC_CD_GPIO;
+			mop500_sdi0_data.cd_invert = true;
+			sdi0_en = SNOWBALL_SDMMC_EN_GPIO;
+			sdi0_vsel = SNOWBALL_SDMMC_1V8_3V_GPIO;
+		}
 		sdi0_configure();
 	}
+
 	/*
 	 * On boards with the TC35892 GPIO expander, sdi0 will finally
 	 * be added when the TC35892 initializes and calls
diff --git a/arch/arm/mach-ux500/board-mop500.h b/arch/arm/mach-ux500/board-mop500.h
index 56722f4..5588164 100644
--- a/arch/arm/mach-ux500/board-mop500.h
+++ b/arch/arm/mach-ux500/board-mop500.h
@@ -7,6 +7,10 @@
 #ifndef __BOARD_MOP500_H
 #define __BOARD_MOP500_H
 
+#define SNOWBALL_SDMMC_EN_GPIO 217
+#define SNOWBALL_SDMMC_1V8_3V_GPIO 228
+#define SNOWBALL_SDMMC_CD_GPIO 218
+
 /* HREFv60-specific GPIO assignments, this board has no GPIO expander */
 #define HREFV60_TOUCH_RST_GPIO		143
 #define HREFV60_PROX_SENSE_GPIO		217
@@ -35,6 +39,7 @@ extern void mop500_sdi_tc35892_init(void);
 void __init mop500_u8500uib_init(void);
 void __init mop500_stuib_init(void);
 void __init mop500_pins_init(void);
+void __init snowball_pins_init(void);
 
 void mop500_uib_i2c_add(int busnum, struct i2c_board_info *info,
 		unsigned n);
diff --git a/arch/arm/mach-ux500/board-snowball.c b/arch/arm/mach-ux500/board-snowball.c
index 3b351ef..ea82c01 100644
--- a/arch/arm/mach-ux500/board-snowball.c
+++ b/arch/arm/mach-ux500/board-snowball.c
@@ -36,7 +36,7 @@
 
 #include "ste-dma40-db8500.h"
 #include "devices-db8500.h"
-#include "board-snowball.h"
+#include "board-mop500.h"
 #include "board-mop500-regulators.h"
 
 static struct ab8500_platform_data ab8500_platdata = {
@@ -243,6 +243,7 @@ static void __init mop500_init_machine(void)
 	platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
 
 	mop500_i2c_init();
+	mop500_sdi_init();
 	mop500_spi_init();
 	mop500_uart_init();
 
-- 
1.7.1

[PATCH 05/10] smsc911x: use shifted register access

[mathieu.poirier at linaro.org]

From: Alessandro Rubini <rubini@gnudd.com>

At least one of the boards using this chip needs a shift in
register access. This adds a "shift" field in the platform data
to have the chip working in all cases without special ifdef.
The approach is similaro to the one used in serial_8250 and other
places.  Performance-wise no difference is reported.

Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
---
 drivers/net/smsc911x.c   |   27 ++++++++++++++++++---------
 include/linux/smsc911x.h |    1 +
 2 files changed, 19 insertions(+), 9 deletions(-)

diff --git a/drivers/net/smsc911x.c b/drivers/net/smsc911x.c
index 64bfdae..a21c551 100644
--- a/drivers/net/smsc911x.c
+++ b/drivers/net/smsc911x.c
@@ -120,12 +120,15 @@ struct smsc911x_data {
 
 static inline u32 __smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg)
 {
+	void __iomem *addr = pdata->ioaddr;
+	int shift = pdata->config.shift;
+
 	if (pdata->config.flags & SMSC911X_USE_32BIT)
-		return readl(pdata->ioaddr + reg);
+		return readl(addr + (reg << shift));
 
 	if (pdata->config.flags & SMSC911X_USE_16BIT)
-		return ((readw(pdata->ioaddr + reg) & 0xFFFF) |
-			((readw(pdata->ioaddr + reg + 2) & 0xFFFF) << 16));
+		return ((readw(addr + (reg << shift)) & 0xFFFF) |
+			((readw(addr + ((reg + 2) << shift)) & 0xFFFF) << 16));
 
 	BUG();
 	return 0;
@@ -146,14 +149,17 @@ static inline u32 smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg)
 static inline void __smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg,
 					u32 val)
 {
+	void __iomem *addr = pdata->ioaddr;
+	int shift = pdata->config.shift;
+
 	if (pdata->config.flags & SMSC911X_USE_32BIT) {
-		writel(val, pdata->ioaddr + reg);
+		writel(val, addr + (reg << shift));
 		return;
 	}
 
 	if (pdata->config.flags & SMSC911X_USE_16BIT) {
-		writew(val & 0xFFFF, pdata->ioaddr + reg);
-		writew((val >> 16) & 0xFFFF, pdata->ioaddr + reg + 2);
+		writew(val & 0xFFFF, addr + (reg << shift));
+		writew((val >> 16) & 0xFFFF, addr + ((reg + 2) << shift));
 		return;
 	}
 
@@ -187,7 +193,8 @@ smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf,
 	}
 
 	if (pdata->config.flags & SMSC911X_USE_32BIT) {
-		writesl(pdata->ioaddr + TX_DATA_FIFO, buf, wordcount);
+		writesl(pdata->ioaddr + (TX_DATA_FIFO << pdata->config.shift),
+			buf, wordcount);
 		goto out;
 	}
 
@@ -219,7 +226,8 @@ smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf,
 	}
 
 	if (pdata->config.flags & SMSC911X_USE_32BIT) {
-		readsl(pdata->ioaddr + RX_DATA_FIFO, buf, wordcount);
+		readsl(pdata->ioaddr + (RX_DATA_FIFO << pdata->config.shift),
+					buf, wordcount);
 		goto out;
 	}
 
@@ -2003,7 +2011,8 @@ static int __devinit smsc911x_drv_probe(struct platform_device *pdev)
 
 	dev->irq = irq_res->start;
 	irq_flags = irq_res->flags & IRQF_TRIGGER_MASK;
-	pdata->ioaddr = ioremap_nocache(res->start, res_size);
+	pdata->ioaddr = ioremap_nocache(res->start,
+					(res_size << config->shift));
 
 	/* copy config parameters across to pdata */
 	memcpy(&pdata->config, config, sizeof(pdata->config));
diff --git a/include/linux/smsc911x.h b/include/linux/smsc911x.h
index 7144e8a..cff97bc 100644
--- a/include/linux/smsc911x.h
+++ b/include/linux/smsc911x.h
@@ -29,6 +29,7 @@ struct smsc911x_platform_config {
 	unsigned int irq_polarity;
 	unsigned int irq_type;
 	unsigned int flags;
+	unsigned int shift; /* for register access */
 	phy_interface_t phy_interface;
 	unsigned char mac[6];
 };
-- 
1.7.1

[PATCH 06/10] ux500: added snowball-netev with latest fixes

[mathieu.poirier at linaro.org]

From: Alessandro Rubini <rubini@gnudd.com>

Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
---
 arch/arm/mach-ux500/board-snowball-netdev.c |   86 +++++++++++++++++++++++++++
 1 files changed, 86 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-ux500/board-snowball-netdev.c

diff --git a/arch/arm/mach-ux500/board-snowball-netdev.c b/arch/arm/mach-ux500/board-snowball-netdev.c
new file mode 100644
index 0000000..ee2ab7a
--- /dev/null
+++ b/arch/arm/mach-ux500/board-snowball-netdev.c
@@ -0,0 +1,86 @@
+/*
+ * Copyright (C) 2010-2011 ST-Ericsson
+ *
+ * Author: Alessandro Rubini <rubini@gnudd.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ */
+
+
+#include <linux/module.h>
+#include <linux/resource.h>
+#include <linux/platform_device.h>
+#include <linux/smsc911x.h>
+#include <mach/irqs.h>
+#include <asm/io.h>
+#include <asm/mach-types.h>
+
+struct smsc911x_platform_config sbnet_cfg = {
+	.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_HIGH,
+	.irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
+	.shift = 1,
+	.flags = SMSC911X_USE_16BIT | SMSC911X_FORCE_INTERNAL_PHY,
+};
+
+struct resource sbnet_res[] = {
+	{
+		.name = "smsc911x-memory",
+		.start = (0x5000 << 16),
+		.end  =  (0x5000 << 16) + 0x3ff,
+		.flags = IORESOURCE_MEM,
+	},{
+		.start = NOMADIK_GPIO_TO_IRQ(140),
+		.end = NOMADIK_GPIO_TO_IRQ(140),
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
+	},
+};
+
+struct platform_device sbnet_dev = {
+	.name		= "smsc911x",
+	.num_resources	= ARRAY_SIZE(sbnet_res),
+	.resource	= sbnet_res,
+	.dev		= {
+		.platform_data = &sbnet_cfg,
+	},
+};
+
+int sbnet_init(void)
+{
+	volatile u32 *ptr = ioremap(0x80000000, 0x10000);
+
+	if (!machine_is_snowball()) {
+		printk("no netdev: no snowball\n");
+		return 0;
+	}
+	printk("init netdev: is snowball\n");
+
+	/*
+	 * Horribly, fix all the configuration by hand
+	 */
+	/* Turn on the FSMC device */
+	*(ptr + 0xf000 / 4) = 1;
+	*(ptr + 0xf008 / 4) = 1;
+
+	/* Configure the FSMC device */
+	*(ptr + 0x0000 / 4) = 0x0000305b;
+	*(ptr + 0x0004 / 4) = 0x01010110;
+
+	/* Fix some gpio bits */
+	*(ptr + 0xe120 / 4) &= ~0x7f8;
+	*(ptr + 0xe124 / 4) |=  0x7f8;
+	iounmap(ptr);
+
+	return platform_device_register(&sbnet_dev);
+}
+
+void sbnet_exit(void)
+{
+	platform_device_unregister(&sbnet_dev);
+}
+
+module_init(sbnet_init);
+module_exit(sbnet_exit);
+
+MODULE_LICENSE("GPL");
-- 
1.7.1

[PATCH 07/10] ux500: added snowball-digio.c

[mathieu.poirier at linaro.org]

From: Alessandro Rubini <rubini@gnudd.com>

This file includes definitions for the output led and 5 input buttons,
4 on the strip on the side and one soldered near the mmc slot.

This work is originally by Gregory Hermant, split by me to a
separate file.

Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
---
 arch/arm/mach-ux500/board-snowball-digio.c |  122 ++++++++++++++++++++++++++++
 1 files changed, 122 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-ux500/board-snowball-digio.c

diff --git a/arch/arm/mach-ux500/board-snowball-digio.c b/arch/arm/mach-ux500/board-snowball-digio.c
new file mode 100644
index 0000000..57f9e3f
--- /dev/null
+++ b/arch/arm/mach-ux500/board-snowball-digio.c
@@ -0,0 +1,122 @@
+/*
+ * Copyright (C) 2010-2011 ST-Ericsson
+ *
+ * This defines the user led (output) and 4-keys gpio keyboard (input)
+ * Original code by Gregory Hermant <gregory.hermant@calao-systems.com>
+ * Split to a standalone file by Alessandro Rubini <rubini@gnudd.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/input.h>
+#include <linux/gpio_keys.h>
+#include <linux/leds.h>
+#include <plat/pincfg.h>
+#include <plat/gpio.h>
+#include "pins-db5500.h"
+
+static pin_cfg_t snowball_pins[] = {
+	PIN_CFG(32, GPIO)     | PIN_INPUT_PULLUP, /* led */
+	PIN_CFG(151, GPIO)	| PIN_INPUT_PULLUP, /* button */
+	PIN_CFG(152, GPIO)	| PIN_INPUT_PULLUP, /* button */
+	PIN_CFG(161, GPIO)	| PIN_INPUT_PULLUP, /* button */
+	PIN_CFG(162, GPIO)	| PIN_INPUT_PULLUP, /* button */
+};
+
+static struct gpio_led snowball_led_array[] = {
+	{
+		.name = "user_led",
+		.default_trigger = "none",
+		.gpio = 142,
+	},
+};
+
+static struct gpio_led_platform_data snowball_led_data = {
+	.leds = snowball_led_array,
+	.num_leds = ARRAY_SIZE(snowball_led_array),
+};
+
+static struct platform_device snowball_led_dev = {
+	.name = "leds-gpio",
+	.dev = {
+		.platform_data = &snowball_led_data,
+	},
+};
+
+static struct gpio_keys_button snowball_key_array[] = {
+	{
+		.gpio		= 32,
+		.type		= EV_KEY,
+		.code		= KEY_1,
+		.desc		= "userpb",
+		.active_low	= 1,
+		.debounce_interval = 50,
+		.wakeup		= 1,
+	},
+	{
+		.gpio		= 151,
+		.type		= EV_KEY,
+		.code		= KEY_2,
+		.desc		= "extkb1",
+		.active_low	= 1,
+		.debounce_interval = 50,
+		.wakeup		= 1,
+	},
+	{
+		.gpio		= 152,
+		.type		= EV_KEY,
+		.code		= KEY_3,
+		.desc		= "extkb2",
+		.active_low	= 1,
+		.debounce_interval = 50,
+		.wakeup		= 1,
+	},
+	{
+		.gpio		= 161,
+		.type		= EV_KEY,
+		.code		= KEY_4,
+		.desc		= "extkb3",
+		.active_low	= 1,
+		.debounce_interval = 50,
+		.wakeup		= 1,
+	},
+	{
+		.gpio		= 162,
+		.type		= EV_KEY,
+		.code		= KEY_5,
+		.desc		= "extkb4",
+		.active_low	= 1,
+		.debounce_interval = 50,
+		.wakeup		= 1,
+	},
+};
+
+static struct gpio_keys_platform_data snowball_key_data = {
+	.buttons	= snowball_key_array,
+	.nbuttons	= ARRAY_SIZE(snowball_key_array),
+};
+
+static struct platform_device snowball_key_dev = {
+	.name		= "gpio-keys",
+	.id		= -1,
+	.dev		= {
+		.platform_data	= &snowball_key_data,
+	}
+};
+
+static int snowball_digio_init(void)
+{
+        nmk_config_pins(snowball_pins, ARRAY_SIZE(snowball_pins));
+	platform_device_register(&snowball_led_dev);
+	platform_device_register(&snowball_key_dev);
+	return 0;
+}
+
+module_init(snowball_digio_init);
+
+/* no release function: I'm lazy at this point */
-- 
1.7.1

[PATCH 08/10] ux500: hooking up netdev and digio to compilation.

[mathieu.poirier at linaro.org]

From: Mathieu J. Poirier <mathieu.poirier@linaro.org>

Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
---
 arch/arm/mach-ux500/Makefile |    2 ++
 1 files changed, 2 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-ux500/Makefile b/arch/arm/mach-ux500/Makefile
index 016cb9f..c7c7c46 100644
--- a/arch/arm/mach-ux500/Makefile
+++ b/arch/arm/mach-ux500/Makefile
@@ -13,6 +13,8 @@ obj-$(CONFIG_MACH_U8500)	+= board-mop500.o board-mop500-sdi.o \
 				board-mop500-pins.o
 obj-$(CONFIG_MACH_U8500_SNOWBALL) += board-snowball.o \
 				board-snowball-pins.o \
+				board-snowball-netdev.o \
+				board-snowball-digio.o \
 				board-mop500-regulators.o board-mop500-sdi.o
 obj-$(CONFIG_MACH_U5500)	+= board-u5500.o board-u5500-sdi.o
 obj-$(CONFIG_SMP)		+= platsmp.o headsmp.o
-- 
1.7.1

[PATCH 09/10] ux500: Addressing irq header file dependency for snowball.

[mathieu.poirier at linaro.org]

From: Mathieu J. Poirier <mathieu.poirier@linaro.org>

Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
---
 arch/arm/mach-ux500/include/mach/irqs.h |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/arch/arm/mach-ux500/include/mach/irqs.h b/arch/arm/mach-ux500/include/mach/irqs.h
index ba1294c..30c6989 100644
--- a/arch/arm/mach-ux500/include/mach/irqs.h
+++ b/arch/arm/mach-ux500/include/mach/irqs.h
@@ -36,7 +36,7 @@
 /* This will be overridden by board-specific irq headers */
 #define IRQ_BOARD_END			IRQ_BOARD_START
 
-#ifdef CONFIG_MACH_U8500
+#if defined CONFIG_MACH_U8500 || CONFIG_MACH_U8500_SNOWBALL
 #include <mach/irqs-board-mop500.h>
 #endif
 
-- 
1.7.1

[PATCH 10/10] ux500: adding config file options for snowball board.

[mathieu.poirier at linaro.org]

From: Mathieu J. Poirier <mathieu.poirier@linaro.org>

Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
---
 arch/arm/configs/u8500_defconfig | 1497 ++++++++++++++++++++++++++++++++++++++
 1 files changed, 1497 insertions(+), 0 deletions(-)

diff --git a/arch/arm/configs/u8500_defconfig b/arch/arm/configs/u8500_defconfig
index e1d6020..12a183b 100644
--- a/arch/arm/configs/u8500_defconfig
+++ b/arch/arm/configs/u8500_defconfig
@@ -1,109 +1,1606 @@
+#
+# Automatically generated make config: don't edit
+# Linux/arm 2.6.38-rc7 Kernel Configuration
+# Fri Mar 11 14:20:28 2011
+#
+CONFIG_ARM=y
+CONFIG_HAVE_PWM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_HAVE_SCHED_CLOCK=y
+CONFIG_GENERIC_GPIO=y
+# CONFIG_ARCH_USES_GETTIMEOFFSET is not set
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
+CONFIG_HAVE_PROC_CPU=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_GENERIC_LOCKBREAK=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_ARCH_HAS_CPUFREQ=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+CONFIG_HAVE_IRQ_WORK=y
+
+#
+# General setup
+#
 CONFIG_EXPERIMENTAL=y
+CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_CROSS_COMPILE=""
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_HAVE_KERNEL_LZO=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_LZMA is not set
+# CONFIG_KERNEL_LZO is not set
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+CONFIG_HAVE_GENERIC_HARDIRQS=y
+
+#
+# IRQ subsystem
+#
+CONFIG_GENERIC_HARDIRQS=y
+# CONFIG_GENERIC_HARDIRQS_NO_DEPRECATED is not set
+CONFIG_HAVE_SPARSE_IRQ=y
+# CONFIG_GENERIC_PENDING_IRQ is not set
+# CONFIG_AUTO_IRQ_AFFINITY is not set
+# CONFIG_IRQ_PER_CPU is not set
+# CONFIG_SPARSE_IRQ is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_TREE_PREEMPT_RCU=y
+CONFIG_PREEMPT_RCU=y
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=17
+# CONFIG_CGROUPS is not set
+CONFIG_NAMESPACES=y
+CONFIG_UTS_NS=y
+CONFIG_IPC_NS=y
+CONFIG_USER_NS=y
+CONFIG_PID_NS=y
+CONFIG_NET_NS=y
+# CONFIG_SCHED_AUTOGROUP is not set
+# CONFIG_SYSFS_DEPRECATED is not set
+# CONFIG_RELAY is not set
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+CONFIG_RD_BZIP2=y
+CONFIG_RD_LZMA=y
+CONFIG_RD_XZ=y
+CONFIG_RD_LZO=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+# CONFIG_EXPERT is not set
+# CONFIG_EMBEDDED is not set
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
 CONFIG_KALLSYMS_ALL=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_PERF_USE_VMALLOC=y
+
+#
+# Kernel Performance Events And Counters
+#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLUB_DEBUG=y
+CONFIG_COMPAT_BRK=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_PROFILING is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_USE_GENERIC_SMP_HELPERS=y
+CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
+CONFIG_HAVE_CLK=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
 CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
 CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_STOP_MACHINE=y
+CONFIG_BLOCK=y
 # CONFIG_LBDAF is not set
 # CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_INLINE_SPIN_TRYLOCK is not set
+# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK is not set
+# CONFIG_INLINE_SPIN_LOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
+# CONFIG_INLINE_SPIN_UNLOCK is not set
+# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
+# CONFIG_INLINE_SPIN_UNLOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_READ_TRYLOCK is not set
+# CONFIG_INLINE_READ_LOCK is not set
+# CONFIG_INLINE_READ_LOCK_BH is not set
+# CONFIG_INLINE_READ_LOCK_IRQ is not set
+# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
+# CONFIG_INLINE_READ_UNLOCK is not set
+# CONFIG_INLINE_READ_UNLOCK_BH is not set
+# CONFIG_INLINE_READ_UNLOCK_IRQ is not set
+# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_WRITE_TRYLOCK is not set
+# CONFIG_INLINE_WRITE_LOCK is not set
+# CONFIG_INLINE_WRITE_LOCK_BH is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
+# CONFIG_INLINE_WRITE_UNLOCK is not set
+# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
+# CONFIG_INLINE_WRITE_UNLOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
+CONFIG_MUTEX_SPIN_ON_OWNER=y
+# CONFIG_FREEZER is not set
+
+#
+# System Type
+#
+CONFIG_MMU=y
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_VEXPRESS is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_BCMRING is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_CNS3XXX is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_MXS is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_DOVE is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_LPC32XX is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_NUC93X is not set
+# CONFIG_ARCH_TEGRA is not set
+# CONFIG_ARCH_PNX4008 is not set
+# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_SHMOBILE is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_S5P64X0 is not set
+# CONFIG_ARCH_S5P6442 is not set
+# CONFIG_ARCH_S5PC100 is not set
+# CONFIG_ARCH_S5PV210 is not set
+# CONFIG_ARCH_S5PV310 is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_TCC_926 is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
 CONFIG_ARCH_U8500=y
+# CONFIG_ARCH_NOMADIK is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+# CONFIG_PLAT_SPEAR is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_KEYBOARD_GPIO_POLLED is not set
+CONFIG_PLAT_NOMADIK=y
+CONFIG_HAS_MTU=y
+CONFIG_NOMADIK_GPIO=y
+
+#
+# System MMU
+#
+CONFIG_UX500_SOC_COMMON=y
+
+#
+# Ux500 SoC
+#
 CONFIG_UX500_SOC_DB5500=y
 CONFIG_UX500_SOC_DB8500=y
+
+#
+# Ux500 target platform
+#
 CONFIG_MACH_U8500=y
+CONFIG_MACH_U8500_SNOWBALL=y
 CONFIG_MACH_U5500=y
+CONFIG_UX500_DEBUG_UART=2
+CONFIG_U5500_MODEM_IRQ=y
+CONFIG_U5500_MBOX=y
+
+#
+# Processor Type
+#
+CONFIG_CPU_32v6K=y
+CONFIG_CPU_V7=y
+CONFIG_CPU_32v7=y
+CONFIG_CPU_ABRT_EV7=y
+CONFIG_CPU_PABRT_V7=y
+CONFIG_CPU_CACHE_V7=y
+CONFIG_CPU_CACHE_VIPT=y
+CONFIG_CPU_COPY_V6=y
+CONFIG_CPU_TLB_V7=y
+CONFIG_CPU_HAS_ASID=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_ARM_THUMBEE is not set
+CONFIG_SWP_EMULATE=y
+# CONFIG_CPU_ICACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_OUTER_CACHE=y
+CONFIG_OUTER_CACHE_SYNC=y
+CONFIG_CACHE_L2X0=y
+CONFIG_CACHE_PL310=y
+CONFIG_ARM_L1_CACHE_SHIFT=5
+CONFIG_ARM_DMA_MEM_BUFFERABLE=y
+CONFIG_CPU_HAS_PMU=y
+# CONFIG_ARM_ERRATA_430973 is not set
+# CONFIG_ARM_ERRATA_458693 is not set
+# CONFIG_ARM_ERRATA_460075 is not set
+# CONFIG_ARM_ERRATA_742230 is not set
+# CONFIG_ARM_ERRATA_742231 is not set
+# CONFIG_ARM_ERRATA_720789 is not set
+# CONFIG_ARM_ERRATA_743622 is not set
+# CONFIG_ARM_ERRATA_751472 is not set
+# CONFIG_ARM_ERRATA_753970 is not set
+CONFIG_ARM_GIC=y
+
+#
+# Bus support
+#
+CONFIG_ARM_AMBA=y
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
 CONFIG_NO_HZ=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
 CONFIG_SMP=y
+CONFIG_SMP_ON_UP=y
+CONFIG_HAVE_ARM_SCU=y
+CONFIG_HAVE_ARM_TWD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
 CONFIG_NR_CPUS=2
 CONFIG_HOTPLUG_CPU=y
+CONFIG_LOCAL_TIMERS=y
+# CONFIG_PREEMPT_NONE is not set
+# CONFIG_PREEMPT_VOLUNTARY is not set
 CONFIG_PREEMPT=y
+CONFIG_HZ=100
+# CONFIG_THUMB2_KERNEL is not set
 CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_COMPACTION is not set
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+# CONFIG_KSM is not set
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_FORCE_MAX_ZONEORDER=11
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+# CONFIG_SECCOMP is not set
+# CONFIG_CC_STACKPROTECTOR is not set
+# CONFIG_DEPRECATED_PARAM_STRUCT is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0
+CONFIG_ZBOOT_ROM_BSS=0
 CONFIG_CMDLINE="root=/dev/ram0 console=ttyAMA2,115200n8"
+# CONFIG_CMDLINE_FORCE is not set
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+# CONFIG_CRASH_DUMP is not set
+# CONFIG_AUTO_ZRELADDR is not set
+
+#
+# CPU Power Management
+#
 CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_TABLE=y
+# CONFIG_CPU_FREQ_DEBUG is not set
+CONFIG_CPU_FREQ_STAT=y
+# CONFIG_CPU_FREQ_STAT_DETAILS is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
 CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set
+# CONFIG_CPU_FREQ_GOV_USERSPACE is not set
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
+# CONFIG_CPU_IDLE is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+# CONFIG_FPE_NWFPE is not set
+# CONFIG_FPE_FASTFPE is not set
 CONFIG_VFP=y
+CONFIG_VFPv3=y
 CONFIG_NEON=y
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS=y
+CONFIG_HAVE_AOUT=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+# CONFIG_PM is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
 CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE_DEMUX is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+CONFIG_INET_LRO=y
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETWORK_PHY_TIMESTAMPING is not set
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+CONFIG_NETFILTER_ADVANCED=y
+
+#
+# Core Netfilter Configuration
+#
+# CONFIG_NETFILTER_NETLINK_QUEUE is not set
+# CONFIG_NETFILTER_NETLINK_LOG is not set
+# CONFIG_NF_CONNTRACK is not set
+# CONFIG_NETFILTER_XTABLES is not set
+# CONFIG_IP_VS is not set
+
+#
+# IP: Netfilter Configuration
+#
+# CONFIG_NF_DEFRAG_IPV4 is not set
+# CONFIG_IP_NF_QUEUE is not set
+# CONFIG_IP_NF_IPTABLES is not set
+# CONFIG_IP_NF_ARPTABLES is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_L2TP is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
 CONFIG_PHONET=y
 CONFIG_PHONET_PIPECTRLR=y
+# CONFIG_IEEE802154 is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+# CONFIG_BATMAN_ADV is not set
+CONFIG_RPS=y
+CONFIG_XPS=y
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
 # CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
 CONFIG_CAIF=y
+# CONFIG_CAIF_DEBUG is not set
+CONFIG_CAIF_NETDEV=y
+# CONFIG_CEPH_LIB is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+# CONFIG_MTD is not set
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+# CONFIG_BLK_DEV_LOOP is not set
+
+#
+# DRBD disabled because PROC_FS, INET or CONNECTOR not selected
+#
+# CONFIG_BLK_DEV_NBD is not set
 CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
 CONFIG_BLK_DEV_RAM_SIZE=65536
+# CONFIG_BLK_DEV_XIP is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MG_DISK is not set
+# CONFIG_BLK_DEV_RBD is not set
 CONFIG_MISC_DEVICES=y
+# CONFIG_AD525X_DPOT is not set
 CONFIG_AB8500_PWM=y
+# CONFIG_ICS932S401 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_APDS9802ALS is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_ISL29020 is not set
+# CONFIG_SENSORS_TSL2550 is not set
 CONFIG_SENSORS_BH1780=y
+# CONFIG_SENSORS_BH1770 is not set
+# CONFIG_SENSORS_APDS990X is not set
+# CONFIG_HMC6352 is not set
+# CONFIG_DS1682 is not set
+# CONFIG_TI_DAC7512 is not set
+# CONFIG_BMP085 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+# CONFIG_EEPROM_AT24 is not set
+# CONFIG_EEPROM_AT25 is not set
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_IWMC3200TOP is not set
+
+#
+# Texas Instruments shared transport line discipline
+#
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+CONFIG_SCSI_MOD=y
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+CONFIG_MII=y
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+CONFIG_SMSC_PHY=y
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_BCM63XX_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_REALTEK_PHY is not set
+# CONFIG_NATIONAL_PHY is not set
+# CONFIG_STE10XP is not set
+# CONFIG_LSI_ET1011C_PHY is not set
+# CONFIG_MICREL_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+# CONFIG_AX88796 is not set
+# CONFIG_SMC91X is not set
+# CONFIG_DM9000 is not set
+# CONFIG_ENC28J60 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+CONFIG_SMSC911X=y
+# CONFIG_SMSC911X_ARCH_HOOKS is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
+# CONFIG_KS8851_MLL is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+# CONFIG_WLAN is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+# CONFIG_WAN is not set
+
+#
+# CAIF transport drivers
+#
+# CONFIG_CAIF_TTY is not set
+# CONFIG_CAIF_SPI_SLAVE is not set
+# CONFIG_CAIF_SHM is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+# CONFIG_INPUT_SPARSEKMAP is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
 # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
 CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
 # CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_KEYBOARD_QT2160 is not set
+# CONFIG_KEYBOARD_LKKBD is not set
 CONFIG_KEYBOARD_GPIO=y
+# CONFIG_KEYBOARD_TCA6416 is not set
+# CONFIG_KEYBOARD_MATRIX is not set
+# CONFIG_KEYBOARD_LM8323 is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
+# CONFIG_KEYBOARD_MCS is not set
+# CONFIG_KEYBOARD_NEWTON is not set
 CONFIG_KEYBOARD_NOMADIK=y
+# CONFIG_KEYBOARD_OPENCORES is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
 CONFIG_KEYBOARD_STMPE=y
 CONFIG_KEYBOARD_TC3589X=y
+# CONFIG_KEYBOARD_XTKBD is not set
 # CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
 CONFIG_INPUT_TOUCHSCREEN=y
+# CONFIG_TOUCHSCREEN_ADS7846 is not set
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
 CONFIG_TOUCHSCREEN_BU21013=y
+# CONFIG_TOUCHSCREEN_CY8CTMG110 is not set
+# CONFIG_TOUCHSCREEN_DYNAPRO is not set
+# CONFIG_TOUCHSCREEN_HAMPSHIRE is not set
+# CONFIG_TOUCHSCREEN_EETI is not set
+# CONFIG_TOUCHSCREEN_FUJITSU is not set
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MCS5000 is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_INEXIO is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
+# CONFIG_TOUCHSCREEN_QT602240 is not set
+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
+# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
+# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
+# CONFIG_TOUCHSCREEN_ST1232 is not set
+# CONFIG_TOUCHSCREEN_STMPE is not set
+# CONFIG_TOUCHSCREEN_TPS6507X is not set
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_AB8500_PONKEY=y
+# CONFIG_INPUT_AD714X is not set
+# CONFIG_INPUT_ATI_REMOTE is not set
+# CONFIG_INPUT_ATI_REMOTE2 is not set
+# CONFIG_INPUT_KEYSPAN_REMOTE is not set
+# CONFIG_INPUT_POWERMATE is not set
+# CONFIG_INPUT_YEALINK is not set
+# CONFIG_INPUT_CM109 is not set
+# CONFIG_INPUT_UINPUT is not set
+# CONFIG_INPUT_PCF8574 is not set
+# CONFIG_INPUT_PWM_BEEPER is not set
+# CONFIG_INPUT_GPIO_ROTARY_ENCODER is not set
+# CONFIG_INPUT_ADXL34X is not set
+# CONFIG_INPUT_CMA3000 is not set
+
+#
+# Hardware I/O ports
+#
 # CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
 CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_N_GSM is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_AMBA_PL010 is not set
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+# CONFIG_SERIAL_MAX3100 is not set
+# CONFIG_SERIAL_MAX3107 is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_TIMBERDALE is not set
+# CONFIG_SERIAL_ALTERA_JTAGUART is not set
+# CONFIG_SERIAL_ALTERA_UART is not set
+# CONFIG_SERIAL_IFX6X60 is not set
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
 # CONFIG_LEGACY_PTYS is not set
+# CONFIG_HVC_DCC is not set
+# CONFIG_IPMI_HANDLER is not set
 CONFIG_HW_RANDOM=y
+# CONFIG_HW_RANDOM_TIMERIOMEM is not set
 CONFIG_HW_RANDOM_NOMADIK=y
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+# CONFIG_RAMOOPS is not set
 CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
+# CONFIG_I2C_CHARDEV is not set
+# CONFIG_I2C_MUX is not set
+CONFIG_I2C_HELPER_AUTO=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+# CONFIG_I2C_GPIO is not set
 CONFIG_I2C_NOMADIK=y
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_XILINX is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
 CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
 CONFIG_SPI_PL022=y
+# CONFIG_SPI_PXA2XX_PCI is not set
+# CONFIG_SPI_XILINX is not set
+# CONFIG_SPI_DESIGNWARE is not set
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
+
+#
+# PPS generators support
+#
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+# CONFIG_GPIO_SYSFS is not set
+
+#
+# Memory mapped GPIO expanders:
+#
+# CONFIG_GPIO_BASIC_MMIO is not set
+# CONFIG_GPIO_IT8761E is not set
+# CONFIG_GPIO_PL061 is not set
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX7300 is not set
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCF857X is not set
+# CONFIG_GPIO_SX150X is not set
 CONFIG_GPIO_STMPE=y
 CONFIG_GPIO_TC3589X=y
+# CONFIG_GPIO_ADP5588 is not set
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_GPIO_MAX7301 is not set
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_GPIO_MC33880 is not set
+# CONFIG_GPIO_74X164 is not set
+
+#
+# AC97 GPIO expanders:
+#
+
+#
+# MODULbus GPIO expanders:
+#
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
 # CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+CONFIG_MFD_SUPPORT=y
+CONFIG_MFD_CORE=y
+# CONFIG_MFD_88PM860X is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_HTC_I2CPLD is not set
+CONFIG_TPS6105X=y
+# CONFIG_TPS65010 is not set
+# CONFIG_TPS6507X is not set
+# CONFIG_TWL4030_CORE is not set
 CONFIG_MFD_STMPE=y
 CONFIG_MFD_TC3589X=y
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_PMIC_ADP5520 is not set
+# CONFIG_MFD_MAX8925 is not set
+# CONFIG_MFD_MAX8998 is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X_I2C is not set
+# CONFIG_MFD_WM831X_SPI is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_WM8994 is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_MFD_MC13XXX is not set
+CONFIG_ABX500_CORE=y
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
 CONFIG_AB8500_CORE=y
+CONFIG_AB8500_I2C_CORE=y
+CONFIG_AB8500_DEBUG=y
+CONFIG_AB8500_GPADC=y
+# CONFIG_AB3550_CORE is not set
+# CONFIG_MFD_TPS6586X is not set
+# CONFIG_MFD_WL1273_CORE is not set
 CONFIG_REGULATOR=y
+# CONFIG_REGULATOR_DEBUG is not set
+# CONFIG_REGULATOR_DUMMY is not set
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
+# CONFIG_REGULATOR_MAX8649 is not set
+# CONFIG_REGULATOR_MAX8660 is not set
+# CONFIG_REGULATOR_MAX8952 is not set
+# CONFIG_REGULATOR_LP3971 is not set
+# CONFIG_REGULATOR_LP3972 is not set
+CONFIG_REGULATOR_TPS6105X=y
+# CONFIG_REGULATOR_TPS65023 is not set
+# CONFIG_REGULATOR_TPS6507X is not set
+# CONFIG_REGULATOR_ISL6271A is not set
+# CONFIG_REGULATOR_AD5398 is not set
 CONFIG_REGULATOR_AB8500=y
+# CONFIG_REGULATOR_TPS6524X is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+CONFIG_DUMMY_CONSOLE=y
+# CONFIG_SOUND is not set
 # CONFIG_HID_SUPPORT is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+# CONFIG_USB_ARCH_HAS_OHCI is not set
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+# CONFIG_USB is not set
 CONFIG_USB_MUSB_HDRC=y
+CONFIG_USB_MUSB_UX500=y
+CONFIG_USB_MUSB_PERIPHERAL=y
 CONFIG_USB_GADGET_MUSB_HDRC=y
 CONFIG_MUSB_PIO_ONLY=y
+# CONFIG_USB_MUSB_DEBUG is not set
+
+#
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
+#
 CONFIG_USB_GADGET=y
+# CONFIG_USB_GADGET_DEBUG is not set
+# CONFIG_USB_GADGET_DEBUG_FILES is not set
+# CONFIG_USB_GADGET_DEBUG_FS is not set
+CONFIG_USB_GADGET_VBUS_DRAW=2
+CONFIG_USB_GADGET_SELECTED=y
+# CONFIG_USB_GADGET_R8A66597 is not set
+# CONFIG_USB_GADGET_PXA_U2O is not set
+# CONFIG_USB_GADGET_M66592 is not set
+CONFIG_USB_GADGET_DUALSPEED=y
+# CONFIG_USB_ZERO is not set
+# CONFIG_USB_ETH is not set
+# CONFIG_USB_G_NCM is not set
+# CONFIG_USB_GADGETFS is not set
+# CONFIG_USB_FUNCTIONFS is not set
+# CONFIG_USB_FILE_STORAGE is not set
+# CONFIG_USB_MASS_STORAGE is not set
+# CONFIG_USB_G_SERIAL is not set
+# CONFIG_USB_G_PRINTER is not set
+# CONFIG_USB_CDC_COMPOSITE is not set
+# CONFIG_USB_G_NOKIA is not set
+# CONFIG_USB_G_MULTI is not set
+# CONFIG_USB_G_HID is not set
+# CONFIG_USB_G_DBGP is not set
+
+#
+# OTG and related infrastructure
+#
+CONFIG_USB_OTG_UTILS=y
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_USB_ULPI is not set
+# CONFIG_NOP_USB_XCEIV is not set
 CONFIG_AB8500_USB=y
 CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+# CONFIG_MMC_CLKGATE is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_MINORS=8
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
 CONFIG_MMC_ARMMMCI=y
+# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_SPI is not set
+# CONFIG_MMC_DW is not set
+# CONFIG_MEMSTICK is not set
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
+
+#
+# LED drivers
+#
+# CONFIG_LEDS_PCA9532 is not set
+# CONFIG_LEDS_GPIO is not set
+# CONFIG_LEDS_LP3944 is not set
 CONFIG_LEDS_LP5521=y
+# CONFIG_LEDS_LP5523 is not set
+# CONFIG_LEDS_PCA955X is not set
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_PWM is not set
+# CONFIG_LEDS_REGULATOR is not set
+# CONFIG_LEDS_BD2802 is not set
+# CONFIG_LEDS_LT3593 is not set
+# CONFIG_LEDS_TRIGGERS is not set
+
+#
+# LED Triggers
+#
+# CONFIG_NFC_DEVICES is not set
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_RTC_LIB=y
 CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_DS3232 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_ISL12022 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_BQ32K is not set
+# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
+
+#
+# SPI RTC drivers
+#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+# CONFIG_RTC_DRV_R9701 is not set
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1286 is not set
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_MSM6242 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_RP5C01 is not set
+# CONFIG_RTC_DRV_V3020 is not set
 CONFIG_RTC_DRV_AB8500=y
+
+#
+# on-CPU RTC drivers
+#
+# CONFIG_RTC_DRV_PL030 is not set
 CONFIG_RTC_DRV_PL031=y
 CONFIG_DMADEVICES=y
+# CONFIG_DMADEVICES_DEBUG is not set
+
+#
+# DMA Devices
+#
+# CONFIG_AMBA_PL08X is not set
 CONFIG_STE_DMA40=y
+# CONFIG_TIMB_DMA is not set
+CONFIG_DMA_ENGINE=y
+
+#
+# DMA Clients
+#
+# CONFIG_NET_DMA is not set
+# CONFIG_ASYNC_TX_DMA is not set
+# CONFIG_DMATEST is not set
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_UIO is not set
 CONFIG_STAGING=y
 # CONFIG_STAGING_EXCLUDE_BUILD is not set
+# CONFIG_ECHO is not set
+# CONFIG_COMEDI is not set
+# CONFIG_POHMELFS is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_IIO is not set
+# CONFIG_ZRAM is not set
+
+#
+# Texas Instruments shared transport line discipline
+#
+# CONFIG_SMB_FS is not set
+CONFIG_MACH_NO_WESTBRIDGE=y
+# CONFIG_FT1000 is not set
+
+#
+# Speakup console speech
+#
+# CONFIG_SPEAKUP is not set
+# CONFIG_TOUCHSCREEN_CLEARPAD_TM1217 is not set
 CONFIG_TOUCHSCREEN_SYNAPTICS_I2C_RMI4=y
+CONFIG_CLKDEV_LOOKUP=y
+
+#
+# File systems
+#
 CONFIG_EXT2_FS=y
 CONFIG_EXT2_FS_XATTR=y
 CONFIG_EXT2_FS_POSIX_ACL=y
 CONFIG_EXT2_FS_SECURITY=y
+# CONFIG_EXT2_FS_XIP is not set
 CONFIG_EXT3_FS=y
+CONFIG_EXT3_DEFAULTS_TO_ORDERED=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4_FS is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_FS_POSIX_ACL=y
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_FANOTIFY is not set
+# CONFIG_QUOTA is not set
+# CONFIG_QUOTACTL is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+CONFIG_GENERIC_ACL=y
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+# CONFIG_MSDOS_FS is not set
 CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
 CONFIG_TMPFS=y
 CONFIG_TMPFS_POSIX_ACL=y
+# CONFIG_HUGETLB_PAGE is not set
 CONFIG_CONFIGFS_FS=m
 # CONFIG_MISC_FILESYSTEMS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+# CONFIG_NFS_V4 is not set
+CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_CEPH_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
 CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
 CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
 CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
+# CONFIG_UNUSED_SYMBOLS is not set
 CONFIG_DEBUG_FS=y
+# CONFIG_HEADERS_CHECK is not set
 CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+# CONFIG_LOCKUP_DETECTOR is not set
+# CONFIG_HARDLOCKUP_DETECTOR is not set
+# CONFIG_DETECT_HUNG_TASK is not set
 # CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_SLUB_STATS is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
 # CONFIG_DEBUG_PREEMPT is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+CONFIG_BKL=y
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_SPARSE_RCU_POINTER is not set
+# CONFIG_LOCK_STAT is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
 CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_INFO_REDUCED is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+CONFIG_DEBUG_MEMORY_INIT=y
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_TEST_LIST_SORT is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
+# CONFIG_LKDTM is not set
+# CONFIG_CPU_NOTIFIER_ERROR_INJECT is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_TRACING_SUPPORT=y
 # CONFIG_FTRACE is not set
+# CONFIG_DYNAMIC_DEBUG is not set
+# CONFIG_DMA_API_DEBUG is not set
+# CONFIG_ATOMIC64_SELFTEST is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+# CONFIG_STRICT_DEVMEM is not set
+CONFIG_ARM_UNWIND=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_ERRORS=y
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+# CONFIG_OC_ETM is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY_DMESG_RESTRICT is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_DEFAULT_SECURITY=""
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG=m
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP2=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+CONFIG_CRYPTO_MANAGER_DISABLE_TESTS=y
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_PCRYPT is not set
+CONFIG_CRYPTO_WORKQUEUE=y
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+CONFIG_CRYPTO_AES=m
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZLIB is not set
+# CONFIG_CRYPTO_LZO is not set
+
+#
+# Random Number Generation
+#
+CONFIG_CRYPTO_ANSI_CPRNG=m
+# CONFIG_CRYPTO_USER_API_HASH is not set
+# CONFIG_CRYPTO_USER_API_SKCIPHER is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+CONFIG_CRC_CCITT=y
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_XZ_DEC=y
+CONFIG_XZ_DEC_X86=y
+CONFIG_XZ_DEC_POWERPC=y
+CONFIG_XZ_DEC_IA64=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_ARMTHUMB=y
+CONFIG_XZ_DEC_SPARC=y
+CONFIG_XZ_DEC_BCJ=y
+# CONFIG_XZ_DEC_TEST is not set
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_DECOMPRESS_BZIP2=y
+CONFIG_DECOMPRESS_LZMA=y
+CONFIG_DECOMPRESS_XZ=y
+CONFIG_DECOMPRESS_LZO=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
-- 
1.7.1

[PATCH 10/10] ux500: adding config file options for snowball board.

[Arnd Bergmann]

On Saturday 12 March 2011 00:08:12 mathieu.poirier at linaro.org wrote:
> From: Mathieu J. Poirier <mathieu.poirier@linaro.org>
> 
> Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
> ---
>  arch/arm/configs/u8500_defconfig | 1497 ++++++++++++++++++++++++++++++++++++++
>  1 files changed, 1497 insertions(+), 0 deletions(-)

Hi Mathieu,

Please use "make savedefconfig" to create a minimal form of this
file, instead of the full .config.

	Arnd

[PATCH 01/10] ux500: Introducing foundation for snowball board.

[Arnd Bergmann]

On Saturday 12 March 2011 00:08:03 mathieu.poirier at linaro.org wrote:
> diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types
> index 9d6feaa..e9f780e 100644
> --- a/arch/arm/tools/mach-types
> +++ b/arch/arm/tools/mach-types
> @@ -3316,3 +3316,4 @@ rover_g8          MACH_ROVER_G8           ROVER_G8                3335
>  t5388p                 MACH_T5388P             T5388P                  3336
>  dingo                  MACH_DINGO              DINGO                   3337
>  goflexhome             MACH_GOFLEXHOME         GOFLEXHOME              3338
> +snowball               MACH_U8500_SNOWBALL     SNOWBALL                3363

I think Russell prefers to update the mach-types file himself
to add all the new types, so while your patch looks totally
fine, it will not go upstream this way.

I'd suggest splitting out the one-line mach-types patch into one
that is only used for review and testing, but leaving the other
changes.

It's also recommended to add the Kconfig change as the final
patch, so that the tree can be compiled at each step of partially
applied patches (if that doesn't already work).

	Arnd

[PATCH 02/10] ux500: Adding new board files for snowball.

[Arnd Bergmann]

On Saturday 12 March 2011 00:08:04 mathieu.poirier at linaro.org wrote:
> From: Mathieu J. Poirier <mathieu.poirier@linaro.org>
> 
> Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>

This changelog would be a good place to explain what the board
is and point to http://www.igloocommunity.org/.

The patch looks good. One question though:

> +
> +static struct pl022_ssp_controller ssp0_platform_data = {
> +	.bus_id = 0,
> +#ifdef CONFIG_STE_DMA40
> +	.enable_dma = 1,
> +	.dma_filter = stedma40_filter,
> +	.dma_rx_param = &ssp0_dma_cfg_rx,
> +	.dma_tx_param = &ssp0_dma_cfg_tx,
> +#else
> +	.enable_dma = 0,
> +#endif
> +	/* on this platform, gpio 31,142,144,214 &
> +	 * 224 are connected as chip selects
> +	 */
> +	.num_chipselect = 5,
> +};

You have a lot of #ifdef CONFIG_STE_DMA40. Is that something
that realistically would be disabled for many users?

If not, you could simply "select STE_DMA40" from the board
Kconfig symbol and make all these unconditional.

	Arnd

[PATCH 04/10] ux500: Adding sdi support on snowball.

[Arnd Bergmann]

On Saturday 12 March 2011 00:08:06 mathieu.poirier at linaro.org wrote:
> @@ -36,7 +36,7 @@
>  
>  #include "ste-dma40-db8500.h"
>  #include "devices-db8500.h"
> -#include "board-snowball.h"
> +#include "board-mop500.h"
>  #include "board-mop500-regulators.h"

Is this change intentional? I'd assume you still want both headers
included here.

	Arnd

[PATCH 02/10] ux500: Adding new board files for snowball.

[Russell King - ARM Linux]

On Sat, Mar 12, 2011 at 10:50:00AM +0100, Arnd Bergmann wrote:
> The patch looks good. One question though:
> 
> > +
> > +static struct pl022_ssp_controller ssp0_platform_data = {
> > +	.bus_id = 0,
> > +#ifdef CONFIG_STE_DMA40
> > +	.enable_dma = 1,
> > +	.dma_filter = stedma40_filter,
> > +	.dma_rx_param = &ssp0_dma_cfg_rx,
> > +	.dma_tx_param = &ssp0_dma_cfg_tx,
> > +#else
> > +	.enable_dma = 0,
> > +#endif
> > +	/* on this platform, gpio 31,142,144,214 &
> > +	 * 224 are connected as chip selects
> > +	 */
> > +	.num_chipselect = 5,
> > +};
> 
> You have a lot of #ifdef CONFIG_STE_DMA40. Is that something
> that realistically would be disabled for many users?
> 
> If not, you could simply "select STE_DMA40" from the board
> Kconfig symbol and make all these unconditional.

Or have the PL022 driver treat failure to claim DMA as a soft failure and
fall back to PIO - and get rid of the .enable_dma thing - which is what
other primecell drivers do.  That way you can keep the initializers there
and leave it to the driver to sort out whether it wants to use DMA or not
depending on whether all the bits are available.

[PATCH 06/10] ux500: added snowball-netev with latest fixes

[Arnd Bergmann]

On Saturday 12 March 2011 00:08:08 mathieu.poirier at linaro.org wrote:
> +int sbnet_init(void)
> +{
> +       volatile u32 *ptr = ioremap(0x80000000, 0x10000);

I suppose you mean "u32 __iomem *" here, not "volatile u32 *ptr".

> +       if (!machine_is_snowball()) {
> +               printk("no netdev: no snowball\n");
> +               return 0;
> +       }
> +       printk("init netdev: is snowball\n");

And pr_debug() instead of printk(), or just remove the
output entirely.

> +       /*
> +        * Horribly, fix all the configuration by hand
> +        */
> +       /* Turn on the FSMC device */
> +       *(ptr + 0xf000 / 4) = 1;
> +       *(ptr + 0xf008 / 4) = 1;
> +
> +       /* Configure the FSMC device */
> +       *(ptr + 0x0000 / 4) = 0x0000305b;
> +       *(ptr + 0x0004 / 4) = 0x01010110;
> +
> +       /* Fix some gpio bits */
> +       *(ptr + 0xe120 / 4) &= ~0x7f8;
> +       *(ptr + 0xe124 / 4) |=  0x7f8;

These need to be writel(), but it would really be
better to pass the configuration in the platform data
and let the driver do it, or do it all in the
firmware.

> +       iounmap(ptr);
> +
> +       return platform_device_register(&sbnet_dev);
> +}

Better use platform_device_register_simple() instead of
the static device.

	Arnd

[PATCH 07/10] ux500: added snowball-digio.c

[Arnd Bergmann]

On Saturday 12 March 2011 00:08:09 mathieu.poirier at linaro.org wrote:
> +static int snowball_digio_init(void)
> +{
> +        nmk_config_pins(snowball_pins, ARRAY_SIZE(snowball_pins));
> +       platform_device_register(&snowball_led_dev);
> +       platform_device_register(&snowball_key_dev);
> +       return 0;
> +}

Whitespace damaged.

Also platform_device_register_data() here.

	Arnd

[PATCH 08/10] ux500: hooking up netdev and digio to compilation.

[Arnd Bergmann]

On Saturday 12 March 2011 00:08:10 mathieu.poirier at linaro.org wrote:
> From: Mathieu J. Poirier <mathieu.poirier@linaro.org>
> 
> Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
> ---
>  arch/arm/mach-ux500/Makefile |    2 ++
>  1 files changed, 2 insertions(+), 0 deletions(-)

It's better to patch the Makefile in the same patch that
adds the file, splitting this in the way you do has no
benefit but makes both patches useless by themselves.

	Arnd

[PATCH 09/10] ux500: Addressing irq header file dependency for snowball.

[Arnd Bergmann]

On Saturday 12 March 2011 00:08:11 mathieu.poirier at linaro.org wrote:
> --- a/arch/arm/mach-ux500/include/mach/irqs.h
> +++ b/arch/arm/mach-ux500/include/mach/irqs.h
> @@ -36,7 +36,7 @@
>  /* This will be overridden by board-specific irq headers */
>  #define IRQ_BOARD_END                  IRQ_BOARD_START
>  
> -#ifdef CONFIG_MACH_U8500
> +#if defined CONFIG_MACH_U8500 || CONFIG_MACH_U8500_SNOWBALL
>  #include <mach/irqs-board-mop500.h>
>  #endif

Can't you just remove the #ifdef entirely? If you want to
be able to build a common kernel, these build-time conditionals
don't work anyway, so the irqs-* files need to be distinct.

The other option would be to remove the #include and directly
include the board specific irqs header from the board file.

In either case, the change would belong in the same patch as
the code that requires it. Just add a short notice about it
in the changelog.

	Arnd

[PATCH 05/10] smsc911x: use shifted register access

[Linus Walleij]

On Sat, Mar 12, 2011 at 12:08 AM,  <mathieu.poirier@linaro.org> wrote:

> From: Alessandro Rubini <rubini@gnudd.com>
>
> At least one of the boards using this chip needs a shift in
> register access. This adds a "shift" field in the platform data
> to have the chip working in all cases without special ifdef.
> The approach is similaro to the one used in serial_8250 and other
> places. ?Performance-wise no difference is reported.
>
> Signed-off-by: Alessandro Rubini <rubini@gnudd.com>

Please send this to the SMSC911x maintainer:

SMSC911x ETHERNET DRIVER
M:      Steve Glendinning <steve.glendinning@smsc.com>
L:      netdev at vger.kernel.org
S:      Supported
F:      include/linux/smsc911x.h
F:      drivers/net/smsc911x.*

Yours,
Linus Walleij

[PATCH 09/10] ux500: Addressing irq header file dependency for snowball.

[Linus Walleij]

On Sat, Mar 12, 2011 at 11:05 AM, Arnd Bergmann <arnd@arndb.de> wrote:
> On Saturday 12 March 2011 00:08:11 mathieu.poirier at linaro.org wrote:
>> --- a/arch/arm/mach-ux500/include/mach/irqs.h
>> +++ b/arch/arm/mach-ux500/include/mach/irqs.h
>> @@ -36,7 +36,7 @@
>> ?/* This will be overridden by board-specific irq headers */
>> ?#define IRQ_BOARD_END ? ? ? ? ? ? ? ? ?IRQ_BOARD_START
>>
>> -#ifdef CONFIG_MACH_U8500
>> +#if defined CONFIG_MACH_U8500 || CONFIG_MACH_U8500_SNOWBALL
>> ?#include <mach/irqs-board-mop500.h>
>> ?#endif
>
> Can't you just remove the #ifdef entirely?

Not only that I think, but merge the entire mach/irqs.h into
irqs-board-mop500.h and get rid of mach/irqs.h altogether is the
proper thing to do. The mach/irqs.h only consider that board
family anyway.

There is no reason why we should be broadcasting a few
board-specific irq defines to the entire kernel in mach/

(Surely I can also patch that up later if need be, though,
note to self.)

Yours,
Linus Walleij

[PATCH 06/10] ux500: added snowball-netev with latest fixes

[Alessandro Rubini]

Hello Arnd.

>> +       volatile u32 *ptr = ioremap(0x80000000, 0x10000);
> 
> I suppose you mean "u32 __iomem *" here, not "volatile u32 *ptr".

Yes, full ack. And also for the rest (as you note, the comment
says "horribly").

Actually, this patch was a quick fix to make things work and proceed
with the board. While other people were working on other devices, I
preferred to (temporarily) have a self-contained hack.

Then I forgot to make it clear to Mathieu that this was not, in my
opinion, ready to get submitted.  Please wait for us to sort this out;
currently I think the patch set should be parked.

> Better use platform_device_register_simple() instead of
> the static device.

Thanks, I didn't know about this.