* [PATCH 1/2] ARM: dts: ux500: Move ab8500 nodes to ste-ab8500.dtsi
@ 2019-08-22 11:07 Stephan Gerhold
2019-08-22 11:07 ` [PATCH 2/2] ARM: dts: ux500: Remove ab8500_ldo_usb regulator from device tree Stephan Gerhold
2019-08-22 15:15 ` [PATCH 1/2] ARM: dts: ux500: Move ab8500 nodes to ste-ab8500.dtsi Linus Walleij
0 siblings, 2 replies; 4+ messages in thread
From: Stephan Gerhold @ 2019-08-22 11:07 UTC (permalink / raw)
To: Linus Walleij
Cc: Mark Rutland, devicetree, Stephan Gerhold, linux-kernel,
Rob Herring, linux-arm-kernel
Some Ux500 devices use the newer AB8505 PMIC instead of AB8500.
Although they are very similar, there are subtle differences
like the number of regulators or the available GPIO pins.
At the moment, ste-dbx5x0.dtsi always configures the AB8500 PMIC.
To support devices with AB8505, it is necessary to split the
AB8500-specific parts into a separate .dtsi file. Boards can then
select the PMIC by including either ste-ab8500.dtsi or ste-ab8505.dtsi.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
---
arch/arm/boot/dts/ste-ab8500.dtsi | 232 +++++++++++++++++++++++++
arch/arm/boot/dts/ste-dbx5x0.dtsi | 208 ----------------------
arch/arm/boot/dts/ste-href-ab8500.dtsi | 2 +
3 files changed, 234 insertions(+), 208 deletions(-)
create mode 100644 arch/arm/boot/dts/ste-ab8500.dtsi
diff --git a/arch/arm/boot/dts/ste-ab8500.dtsi b/arch/arm/boot/dts/ste-ab8500.dtsi
new file mode 100644
index 000000000000..3ef1906e375c
--- /dev/null
+++ b/arch/arm/boot/dts/ste-ab8500.dtsi
@@ -0,0 +1,232 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Linaro Ltd
+ */
+
+#include <dt-bindings/clock/ste-ab8500.h>
+
+/ {
+ soc {
+ prcmu@80157000 {
+ ab8500 {
+ compatible = "stericsson,ab8500";
+ interrupt-parent = <&intc>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ ab8500_clock: clock-controller {
+ compatible = "stericsson,ab8500-clk";
+ #clock-cells = <1>;
+ };
+
+ ab8500_gpio: ab8500-gpio {
+ compatible = "stericsson,ab8500-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ ab8500-rtc {
+ compatible = "stericsson,ab8500-rtc";
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH
+ 18 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "60S", "ALARM";
+ };
+
+ ab8500-gpadc {
+ compatible = "stericsson,ab8500-gpadc";
+ interrupts = <32 IRQ_TYPE_LEVEL_HIGH
+ 39 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "HW_CONV_END", "SW_CONV_END";
+ vddadc-supply = <&ab8500_ldo_tvout_reg>;
+ };
+
+ ab8500_battery: ab8500_battery {
+ stericsson,battery-type = "LIPO";
+ thermistor-on-batctrl;
+ };
+
+ ab8500_fg {
+ compatible = "stericsson,ab8500-fg";
+ battery = <&ab8500_battery>;
+ };
+
+ ab8500_btemp {
+ compatible = "stericsson,ab8500-btemp";
+ battery = <&ab8500_battery>;
+ };
+
+ ab8500_charger {
+ compatible = "stericsson,ab8500-charger";
+ battery = <&ab8500_battery>;
+ vddadc-supply = <&ab8500_ldo_tvout_reg>;
+ };
+
+ ab8500_chargalg {
+ compatible = "stericsson,ab8500-chargalg";
+ battery = <&ab8500_battery>;
+ };
+
+ ab8500_usb {
+ compatible = "stericsson,ab8500-usb";
+ interrupts = < 90 IRQ_TYPE_LEVEL_HIGH
+ 96 IRQ_TYPE_LEVEL_HIGH
+ 14 IRQ_TYPE_LEVEL_HIGH
+ 15 IRQ_TYPE_LEVEL_HIGH
+ 79 IRQ_TYPE_LEVEL_HIGH
+ 74 IRQ_TYPE_LEVEL_HIGH
+ 75 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "ID_WAKEUP_R",
+ "ID_WAKEUP_F",
+ "VBUS_DET_F",
+ "VBUS_DET_R",
+ "USB_LINK_STATUS",
+ "USB_ADP_PROBE_PLUG",
+ "USB_ADP_PROBE_UNPLUG";
+ vddulpivio18-supply = <&ab8500_ldo_intcore_reg>;
+ v-ape-supply = <&db8500_vape_reg>;
+ musb_1v8-supply = <&db8500_vsmps2_reg>;
+ clocks = <&prcmu_clk PRCMU_SYSCLK>;
+ clock-names = "sysclk";
+ };
+
+ ab8500-ponkey {
+ compatible = "stericsson,ab8500-poweron-key";
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH
+ 7 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
+ };
+
+ ab8500-sysctrl {
+ compatible = "stericsson,ab8500-sysctrl";
+ };
+
+ ab8500-pwm {
+ compatible = "stericsson,ab8500-pwm";
+ clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
+ clock-names = "intclk";
+ };
+
+ ab8500-debugfs {
+ compatible = "stericsson,ab8500-debug";
+ };
+
+ codec: ab8500-codec {
+ compatible = "stericsson,ab8500-codec";
+
+ V-AUD-supply = <&ab8500_ldo_audio_reg>;
+ V-AMIC1-supply = <&ab8500_ldo_anamic1_reg>;
+ V-AMIC2-supply = <&ab8500_ldo_anamic2_reg>;
+ V-DMIC-supply = <&ab8500_ldo_dmic_reg>;
+
+ clocks = <&ab8500_clock AB8500_SYSCLK_AUDIO>;
+ clock-names = "audioclk";
+
+ stericsson,earpeice-cmv = <950>; /* Units in mV. */
+ };
+
+ ext_regulators: ab8500-ext-regulators {
+ compatible = "stericsson,ab8500-ext-regulator";
+
+ ab8500_ext1_reg: ab8500_ext1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ab8500_ext2_reg: ab8500_ext2 {
+ regulator-min-microvolt = <1360000>;
+ regulator-max-microvolt = <1360000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ab8500_ext3_reg: ab8500_ext3 {
+ regulator-min-microvolt = <3400000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-boot-on;
+ };
+ };
+
+ ab8500-regulators {
+ compatible = "stericsson,ab8500-regulator";
+ vin-supply = <&ab8500_ext3_reg>;
+
+ // supplies to the display/camera
+ ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2900000>;
+ regulator-boot-on;
+ /* BUG: If turned off MMC will be affected. */
+ regulator-always-on;
+ };
+
+ // supplies to the on-board eMMC
+ ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ // supply for VAUX3; SDcard slots
+ ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ // supply for v-intcore12; VINTCORE12 LDO
+ ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
+ };
+
+ // supply for tvout; gpadc; TVOUT LDO
+ ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
+ };
+
+ // supply for ab8500-usb; USB LDO
+ ab8500_ldo_usb_reg: ab8500_ldo_usb {
+ };
+
+ // supply for ab8500-vaudio; VAUDIO LDO
+ ab8500_ldo_audio_reg: ab8500_ldo_audio {
+ };
+
+ // supply for v-anamic1 VAMIC1 LDO
+ ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
+ };
+
+ // supply for v-amic2; VAMIC2 LDO; reuse constants for AMIC1
+ ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
+ };
+
+ // supply for v-dmic; VDMIC LDO
+ ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
+ };
+
+ // supply for U8500 CSI/DSI; VANA LDO
+ ab8500_ldo_ana_reg: ab8500_ldo_ana {
+ };
+ };
+ };
+ };
+
+ sound {
+ stericsson,audio-codec = <&codec>;
+ clocks = <&prcmu_clk PRCMU_SYSCLK>, <&ab8500_clock AB8500_SYSCLK_ULP>, <&ab8500_clock AB8500_SYSCLK_INT>;
+ clock-names = "sysclk", "ulpclk", "intclk";
+ };
+
+ mcde@a0350000 {
+ vana-supply = <&ab8500_ldo_ana_reg>;
+
+ dsi@a0351000 {
+ vana-supply = <&ab8500_ldo_ana_reg>;
+ };
+ dsi@a0352000 {
+ vana-supply = <&ab8500_ldo_ana_reg>;
+ };
+ dsi@a0353000 {
+ vana-supply = <&ab8500_ldo_ana_reg>;
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi
index b1a31134f860..b9b63fc41e47 100644
--- a/arch/arm/boot/dts/ste-dbx5x0.dtsi
+++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi
@@ -8,7 +8,6 @@
#include <dt-bindings/mfd/dbx500-prcmu.h>
#include <dt-bindings/arm/ux500_pm_domains.h>
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clock/ste-ab8500.h>
/ {
#address-cells = <1>;
@@ -597,206 +596,6 @@
db8500_esram34_ret_reg: db8500_esram34_ret {
};
};
-
- ab8500 {
- compatible = "stericsson,ab8500";
- interrupt-parent = <&intc>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-controller;
- #interrupt-cells = <2>;
-
- ab8500_clock: clock-controller {
- compatible = "stericsson,ab8500-clk";
- #clock-cells = <1>;
- };
-
- ab8500_gpio: ab8500-gpio {
- compatible = "stericsson,ab8500-gpio";
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- ab8500-rtc {
- compatible = "stericsson,ab8500-rtc";
- interrupts = <17 IRQ_TYPE_LEVEL_HIGH
- 18 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "60S", "ALARM";
- };
-
- ab8500-gpadc {
- compatible = "stericsson,ab8500-gpadc";
- interrupts = <32 IRQ_TYPE_LEVEL_HIGH
- 39 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "HW_CONV_END", "SW_CONV_END";
- vddadc-supply = <&ab8500_ldo_tvout_reg>;
- };
-
- ab8500_battery: ab8500_battery {
- stericsson,battery-type = "LIPO";
- thermistor-on-batctrl;
- };
-
- ab8500_fg {
- compatible = "stericsson,ab8500-fg";
- battery = <&ab8500_battery>;
- };
-
- ab8500_btemp {
- compatible = "stericsson,ab8500-btemp";
- battery = <&ab8500_battery>;
- };
-
- ab8500_charger {
- compatible = "stericsson,ab8500-charger";
- battery = <&ab8500_battery>;
- vddadc-supply = <&ab8500_ldo_tvout_reg>;
- };
-
- ab8500_chargalg {
- compatible = "stericsson,ab8500-chargalg";
- battery = <&ab8500_battery>;
- };
-
- ab8500_usb {
- compatible = "stericsson,ab8500-usb";
- interrupts = < 90 IRQ_TYPE_LEVEL_HIGH
- 96 IRQ_TYPE_LEVEL_HIGH
- 14 IRQ_TYPE_LEVEL_HIGH
- 15 IRQ_TYPE_LEVEL_HIGH
- 79 IRQ_TYPE_LEVEL_HIGH
- 74 IRQ_TYPE_LEVEL_HIGH
- 75 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "ID_WAKEUP_R",
- "ID_WAKEUP_F",
- "VBUS_DET_F",
- "VBUS_DET_R",
- "USB_LINK_STATUS",
- "USB_ADP_PROBE_PLUG",
- "USB_ADP_PROBE_UNPLUG";
- vddulpivio18-supply = <&ab8500_ldo_intcore_reg>;
- v-ape-supply = <&db8500_vape_reg>;
- musb_1v8-supply = <&db8500_vsmps2_reg>;
- clocks = <&prcmu_clk PRCMU_SYSCLK>;
- clock-names = "sysclk";
- };
-
- ab8500-ponkey {
- compatible = "stericsson,ab8500-poweron-key";
- interrupts = <6 IRQ_TYPE_LEVEL_HIGH
- 7 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
- };
-
- ab8500-sysctrl {
- compatible = "stericsson,ab8500-sysctrl";
- };
-
- ab8500-pwm {
- compatible = "stericsson,ab8500-pwm";
- clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
- clock-names = "intclk";
- };
-
- ab8500-debugfs {
- compatible = "stericsson,ab8500-debug";
- };
-
- codec: ab8500-codec {
- compatible = "stericsson,ab8500-codec";
-
- V-AUD-supply = <&ab8500_ldo_audio_reg>;
- V-AMIC1-supply = <&ab8500_ldo_anamic1_reg>;
- V-AMIC2-supply = <&ab8500_ldo_anamic2_reg>;
- V-DMIC-supply = <&ab8500_ldo_dmic_reg>;
-
- clocks = <&ab8500_clock AB8500_SYSCLK_AUDIO>;
- clock-names = "audioclk";
-
- stericsson,earpeice-cmv = <950>; /* Units in mV. */
- };
-
- ext_regulators: ab8500-ext-regulators {
- compatible = "stericsson,ab8500-ext-regulator";
-
- ab8500_ext1_reg: ab8500_ext1 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ab8500_ext2_reg: ab8500_ext2 {
- regulator-min-microvolt = <1360000>;
- regulator-max-microvolt = <1360000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ab8500_ext3_reg: ab8500_ext3 {
- regulator-min-microvolt = <3400000>;
- regulator-max-microvolt = <3400000>;
- regulator-boot-on;
- };
- };
-
- ab8500-regulators {
- compatible = "stericsson,ab8500-regulator";
- vin-supply = <&ab8500_ext3_reg>;
-
- // supplies to the display/camera
- ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <2900000>;
- regulator-boot-on;
- /* BUG: If turned off MMC will be affected. */
- regulator-always-on;
- };
-
- // supplies to the on-board eMMC
- ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <3300000>;
- };
-
- // supply for VAUX3; SDcard slots
- ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <3300000>;
- };
-
- // supply for v-intcore12; VINTCORE12 LDO
- ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
- };
-
- // supply for tvout; gpadc; TVOUT LDO
- ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
- };
-
- // supply for ab8500-usb; USB LDO
- ab8500_ldo_usb_reg: ab8500_ldo_usb {
- };
-
- // supply for ab8500-vaudio; VAUDIO LDO
- ab8500_ldo_audio_reg: ab8500_ldo_audio {
- };
-
- // supply for v-anamic1 VAMIC1 LDO
- ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
- };
-
- // supply for v-amic2; VAMIC2 LDO; reuse constants for AMIC1
- ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
- };
-
- // supply for v-dmic; VDMIC LDO
- ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
- };
-
- // supply for U8500 CSI/DSI; VANA LDO
- ab8500_ldo_ana_reg: ab8500_ldo_ana {
- };
- };
- };
};
i2c@80004000 {
@@ -1110,9 +909,6 @@
sound {
compatible = "stericsson,snd-soc-mop500";
stericsson,cpu-dai = <&msp1 &msp3>;
- stericsson,audio-codec = <&codec>;
- clocks = <&prcmu_clk PRCMU_SYSCLK>, <&ab8500_clock AB8500_SYSCLK_ULP>, <&ab8500_clock AB8500_SYSCLK_INT>;
- clock-names = "sysclk", "ulpclk", "intclk";
};
msp0: msp@80123000 {
@@ -1219,7 +1015,6 @@
reg = <0xa0350000 0x1000>;
interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
epod-supply = <&db8500_b2r2_mcde_reg>;
- vana-supply = <&ab8500_ldo_ana_reg>;
clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */
<&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */
<&prcmu_clk PRCMU_PLLDSI>; /* HDMI clock */
@@ -1232,7 +1027,6 @@
dsi0: dsi@a0351000 {
compatible = "ste,mcde-dsi";
reg = <0xa0351000 0x1000>;
- vana-supply = <&ab8500_ldo_ana_reg>;
clocks = <&prcmu_clk PRCMU_DSI0CLK>, <&prcmu_clk PRCMU_DSI0ESCCLK>;
clock-names = "hs", "lp";
#address-cells = <1>;
@@ -1241,7 +1035,6 @@
dsi1: dsi@a0352000 {
compatible = "ste,mcde-dsi";
reg = <0xa0352000 0x1000>;
- vana-supply = <&ab8500_ldo_ana_reg>;
clocks = <&prcmu_clk PRCMU_DSI1CLK>, <&prcmu_clk PRCMU_DSI1ESCCLK>;
clock-names = "hs", "lp";
#address-cells = <1>;
@@ -1250,7 +1043,6 @@
dsi2: dsi@a0353000 {
compatible = "ste,mcde-dsi";
reg = <0xa0353000 0x1000>;
- vana-supply = <&ab8500_ldo_ana_reg>;
/* This DSI port only has the Low Power / Energy Save clock */
clocks = <&prcmu_clk PRCMU_DSI2ESCCLK>;
clock-names = "lp";
diff --git a/arch/arm/boot/dts/ste-href-ab8500.dtsi b/arch/arm/boot/dts/ste-href-ab8500.dtsi
index 8e3e947d181f..4946743de7b9 100644
--- a/arch/arm/boot/dts/ste-href-ab8500.dtsi
+++ b/arch/arm/boot/dts/ste-href-ab8500.dtsi
@@ -3,6 +3,8 @@
* Copyright 2014 Linaro Ltd.
*/
+#include "ste-ab8500.dtsi"
+
/ {
soc {
prcmu@80157000 {
--
2.22.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH 2/2] ARM: dts: ux500: Remove ab8500_ldo_usb regulator from device tree
2019-08-22 11:07 [PATCH 1/2] ARM: dts: ux500: Move ab8500 nodes to ste-ab8500.dtsi Stephan Gerhold
@ 2019-08-22 11:07 ` Stephan Gerhold
2019-08-22 15:16 ` Linus Walleij
2019-08-22 15:15 ` [PATCH 1/2] ARM: dts: ux500: Move ab8500 nodes to ste-ab8500.dtsi Linus Walleij
1 sibling, 1 reply; 4+ messages in thread
From: Stephan Gerhold @ 2019-08-22 11:07 UTC (permalink / raw)
To: Linus Walleij
Cc: Mark Rutland, devicetree, Stephan Gerhold, linux-kernel,
Rob Herring, linux-arm-kernel
Support for the USB regulator of AB8500 was removed in
commit 41a06aa738ad ("regulator: ab8500: Remove USB regulator").
However, the configuration was never removed from the device tree.
It does no longer have any effect, remove it from the device tree.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
---
arch/arm/boot/dts/ste-ab8500.dtsi | 4 ----
arch/arm/boot/dts/ste-href.dtsi | 4 ----
arch/arm/boot/dts/ste-snowball.dts | 4 ----
3 files changed, 12 deletions(-)
diff --git a/arch/arm/boot/dts/ste-ab8500.dtsi b/arch/arm/boot/dts/ste-ab8500.dtsi
index 3ef1906e375c..55fff4d44277 100644
--- a/arch/arm/boot/dts/ste-ab8500.dtsi
+++ b/arch/arm/boot/dts/ste-ab8500.dtsi
@@ -182,10 +182,6 @@
ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
};
- // supply for ab8500-usb; USB LDO
- ab8500_ldo_usb_reg: ab8500_ldo_usb {
- };
-
// supply for ab8500-vaudio; VAUDIO LDO
ab8500_ldo_audio_reg: ab8500_ldo_audio {
};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 6422c53f2046..4f6acbd8c040 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -234,10 +234,6 @@
regulator-name = "V-TVOUT";
};
- ab8500_ldo_usb_reg: ab8500_ldo_usb {
- regulator-name = "dummy";
- };
-
ab8500_ldo_audio_reg: ab8500_ldo_audio {
regulator-name = "V-AUD";
};
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 3428290644ba..c6074912c368 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -474,10 +474,6 @@
regulator-name = "V-TVOUT";
};
- ab8500_ldo_usb_reg: ab8500_ldo_usb {
- regulator-name = "dummy";
- };
-
ab8500_ldo_audio_reg: ab8500_ldo_audio {
regulator-name = "V-AUD";
};
--
2.22.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 4+ messages in thread* Re: [PATCH 1/2] ARM: dts: ux500: Move ab8500 nodes to ste-ab8500.dtsi
2019-08-22 11:07 [PATCH 1/2] ARM: dts: ux500: Move ab8500 nodes to ste-ab8500.dtsi Stephan Gerhold
2019-08-22 11:07 ` [PATCH 2/2] ARM: dts: ux500: Remove ab8500_ldo_usb regulator from device tree Stephan Gerhold
@ 2019-08-22 15:15 ` Linus Walleij
1 sibling, 0 replies; 4+ messages in thread
From: Linus Walleij @ 2019-08-22 15:15 UTC (permalink / raw)
To: Stephan Gerhold
Cc: Mark Rutland,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Rob Herring, linux-kernel, Linux ARM
On Thu, Aug 22, 2019 at 1:08 PM Stephan Gerhold <stephan@gerhold.net> wrote:
> Some Ux500 devices use the newer AB8505 PMIC instead of AB8500.
> Although they are very similar, there are subtle differences
> like the number of regulators or the available GPIO pins.
>
> At the moment, ste-dbx5x0.dtsi always configures the AB8500 PMIC.
> To support devices with AB8505, it is necessary to split the
> AB8500-specific parts into a separate .dtsi file. Boards can then
> select the PMIC by including either ste-ab8500.dtsi or ste-ab8505.dtsi.
>
> Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Patch applied to the Ux500 tree!
Thanks!
Linus Walleij
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2019-08-22 15:17 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-08-22 11:07 [PATCH 1/2] ARM: dts: ux500: Move ab8500 nodes to ste-ab8500.dtsi Stephan Gerhold
2019-08-22 11:07 ` [PATCH 2/2] ARM: dts: ux500: Remove ab8500_ldo_usb regulator from device tree Stephan Gerhold
2019-08-22 15:16 ` Linus Walleij
2019-08-22 15:15 ` [PATCH 1/2] ARM: dts: ux500: Move ab8500 nodes to ste-ab8500.dtsi Linus Walleij
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).