[PATCH v3 5/5] gpio: Add in ast2600 details to Aspeed driver

[PATCH v3 5/5] gpio: Add in ast2600 details to Aspeed driver

[Rashmica Gupta]

The ast2600 is a new generation of SoC from ASPEED. Similarly to the
ast2400 and ast2500, it has a GPIO controller for it's 3.3V GPIO pins.
Additionally, it has a GPIO controller for 1.8V GPIO pins.

As the register names for both controllers are the same and the 36 1.8V
GPIOs and the first 36 of the 3.3V GPIOs are all bidirectional, we can
use the same configuration struct and use the ngpio property to
differentiate between the two sets of GPIOs.

Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
---
 drivers/gpio/gpio-aspeed.c | 22 ++++++++++++++++++++--
 1 file changed, 20 insertions(+), 2 deletions(-)

diff --git a/drivers/gpio/gpio-aspeed.c b/drivers/gpio/gpio-aspeed.c
index effcfaaf8c0c..22d482072632 100644
--- a/drivers/gpio/gpio-aspeed.c
+++ b/drivers/gpio/gpio-aspeed.c
@@ -662,12 +662,14 @@ static void aspeed_gpio_irq_handler(struct irq_desc *desc)
 	struct gpio_chip *gc = irq_desc_get_handler_data(desc);
 	struct irq_chip *ic = irq_desc_get_chip(desc);
 	struct aspeed_gpio *data = gpiochip_get_data(gc);
-	unsigned int i, p, girq;
+	unsigned int i, p, girq, banks;
 	unsigned long reg;
+	struct aspeed_gpio *gpio = gpiochip_get_data(gc);
 
 	chained_irq_enter(ic, desc);
 
-	for (i = 0; i < ARRAY_SIZE(aspeed_gpio_banks); i++) {
+	banks = DIV_ROUND_UP(gpio->chip.ngpio, 32);
+	for (i = 0; i < banks; i++) {
 		const struct aspeed_gpio_bank *bank = &aspeed_gpio_banks[i];
 
 		reg = ioread32(bank_reg(data, bank, reg_irq_status));
@@ -1134,9 +1136,25 @@ static const struct aspeed_gpio_config ast2500_config =
 	/* 232 for simplicity, actual number is 228 (4-GPIO hole in GPIOAB) */
 	{ .nr_gpios = 232, .props = ast2500_bank_props, };
 
+static const struct aspeed_bank_props ast2600_bank_props[] = {
+	/*     input	  output   */
+	{5, 0xffffffff,  0x0000ffff}, /* U/V/W/X */
+	{6, 0xffff0000,  0x0fff0000}, /* Y/Z */
+	{ },
+};
+
+static const struct aspeed_gpio_config ast2600_config =
+	/*
+	 * ast2600 has two controllers one with 208 GPIOs and one with 36 GPIOs.
+	 * We expect ngpio being set in the device tree and this is a fallback
+	 * option.
+	 */
+	{ .nr_gpios = 208, .props = ast2600_bank_props, };
+
 static const struct of_device_id aspeed_gpio_of_table[] = {
 	{ .compatible = "aspeed,ast2400-gpio", .data = &ast2400_config, },
 	{ .compatible = "aspeed,ast2500-gpio", .data = &ast2500_config, },
+	{ .compatible = "aspeed,ast2600-gpio", .data = &ast2600_config, },
 	{}
 };
 MODULE_DEVICE_TABLE(of, aspeed_gpio_of_table);
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 5/5] gpio: Add in ast2600 details to Aspeed driver

[Linus Walleij]

On Fri, Sep 6, 2019 at 7:37 AM Rashmica Gupta <rashmica.g@gmail.com> wrote:

> The ast2600 is a new generation of SoC from ASPEED. Similarly to the
> ast2400 and ast2500, it has a GPIO controller for it's 3.3V GPIO pins.
> Additionally, it has a GPIO controller for 1.8V GPIO pins.
>
> As the register names for both controllers are the same and the 36 1.8V
> GPIOs and the first 36 of the 3.3V GPIOs are all bidirectional, we can
> use the same configuration struct and use the ngpio property to
> differentiate between the two sets of GPIOs.
>
> Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>

Patch applied.

Yours,
Linus Walleij

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel