* [PATCHv3 2/3] arm64: dts: ls1028a: Add PCIe controller DT nodes
2019-08-06 6:15 [PATCHv3 1/3] dt-bindings: pci: layerscape-pci: add compatible strings "fsl, ls1028a-pcie" Xiaowei Bao
@ 2019-08-06 6:15 ` Xiaowei Bao
2019-08-16 4:17 ` Z.q. Hou
2019-08-06 6:15 ` [PATCHv3 3/3] PCI: layerscape: Add LS1028a support Xiaowei Bao
2019-08-21 19:26 ` [PATCHv3 1/3] dt-bindings: pci: layerscape-pci: add compatible strings "fsl,ls1028a-pcie" Rob Herring
2 siblings, 1 reply; 5+ messages in thread
From: Xiaowei Bao @ 2019-08-06 6:15 UTC (permalink / raw)
To: bhelgaas, robh+dt, mark.rutland, shawnguo, leoyang.li, kishon,
lorenzo.pieralisi, arnd, gregkh, minghuan.Lian, mingkai.hu,
zhiqiang.hou, roy.zang, kstewart, pombredanne, shawn.lin,
linux-pci, devicetree, linux-kernel, linux-arm-kernel,
linuxppc-dev
Cc: Hou Zhiqiang, Xiaowei Bao
LS1028a implements 2 PCIe 3.0 controllers.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
---
v2:
- Fix up the legacy INTx allocate failed issue.
v3:
- no change.
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 52 ++++++++++++++++++++++++++
1 file changed, 52 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
index aef5b06..0b542ed 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
@@ -503,6 +503,58 @@
status = "disabled";
};
+ pcie@3400000 {
+ compatible = "fsl,ls1028a-pcie";
+ reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */
+ 0x80 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
+ <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; /* aer interrupt */
+ interrupt-names = "pme", "aer";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ dma-coherent;
+ num-lanes = <4>;
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x00000000 0x80 0x00010000 0x0 0x00010000 /* downstream I/O */
+ 0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ msi-parent = <&its>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+ <0000 0 0 2 &gic 0 0 GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+ <0000 0 0 3 &gic 0 0 GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+ <0000 0 0 4 &gic 0 0 GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ pcie@3500000 {
+ compatible = "fsl,ls1028a-pcie";
+ reg = <0x00 0x03500000 0x0 0x00100000 /* controller registers */
+ 0x88 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
+ interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "pme", "aer";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ dma-coherent;
+ num-lanes = <4>;
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x00000000 0x88 0x00010000 0x0 0x00010000 /* downstream I/O */
+ 0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ msi-parent = <&its>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+ <0000 0 0 2 &gic 0 0 GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+ <0000 0 0 3 &gic 0 0 GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+ <0000 0 0 4 &gic 0 0 GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
pcie@1f0000000 { /* Integrated Endpoint Root Complex */
compatible = "pci-host-ecam-generic";
reg = <0x01 0xf0000000 0x0 0x100000>;
--
2.9.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 5+ messages in thread* RE: [PATCHv3 2/3] arm64: dts: ls1028a: Add PCIe controller DT nodes
2019-08-06 6:15 ` [PATCHv3 2/3] arm64: dts: ls1028a: Add PCIe controller DT nodes Xiaowei Bao
@ 2019-08-16 4:17 ` Z.q. Hou
0 siblings, 0 replies; 5+ messages in thread
From: Z.q. Hou @ 2019-08-16 4:17 UTC (permalink / raw)
To: Xiaowei Bao, bhelgaas, robh+dt, mark.rutland, shawnguo, Leo Li,
kishon, lorenzo.pieralisi, arnd, gregkh, M.h. Lian, Mingkai Hu,
Roy Zang, kstewart, pombredanne, shawn.lin, linux-pci,
devicetree, linux-kernel, linux-arm-kernel, linuxppc-dev
Cc: Xiaowei Bao
Hi Xiaowei,
> -----Original Message-----
> From: Xiaowei Bao <xiaowei.bao@nxp.com>
> Sent: 2019年8月6日 14:16
> To: bhelgaas@google.com; robh+dt@kernel.org; mark.rutland@arm.com;
> shawnguo@kernel.org; Leo Li <leoyang.li@nxp.com>; kishon@ti.com;
> lorenzo.pieralisi@arm.com; arnd@arndb.de; gregkh@linuxfoundation.org;
> M.h. Lian <minghuan.lian@nxp.com>; Mingkai Hu <mingkai.hu@nxp.com>;
> Z.q. Hou <zhiqiang.hou@nxp.com>; Roy Zang <roy.zang@nxp.com>;
> kstewart@linuxfoundation.org; pombredanne@nexb.com;
> shawn.lin@rock-chips.com; linux-pci@vger.kernel.org;
> devicetree@vger.kernel.org; linux-kernel@vger.kernel.org;
> linux-arm-kernel@lists.infradead.org; linuxppc-dev@lists.ozlabs.org
> Cc: Xiaowei Bao <xiaowei.bao@nxp.com>; Z.q. Hou
> <zhiqiang.hou@nxp.com>
> Subject: [PATCHv3 2/3] arm64: dts: ls1028a: Add PCIe controller DT nodes
>
> LS1028a implements 2 PCIe 3.0 controllers.
>
> Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
> ---
> v2:
> - Fix up the legacy INTx allocate failed issue.
> v3:
> - no change.
>
> arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 52
> ++++++++++++++++++++++++++
> 1 file changed, 52 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> index aef5b06..0b542ed 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> @@ -503,6 +503,58 @@
> status = "disabled";
> };
>
> + pcie@3400000 {
> + compatible = "fsl,ls1028a-pcie";
> + reg = <0x00 0x03400000 0x0 0x00100000 /* controller
> registers */
> + 0x80 0x00000000 0x0 0x00002000>; /* configuration
> space */
> + reg-names = "regs", "config";
> + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* PME
> interrupt */
> + <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; /* aer
> interrupt */
> + interrupt-names = "pme", "aer";
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + dma-coherent;
> + num-lanes = <4>;
Remove the num-lanes, it is not needed by Layerscape PCIe controllers. see: http://patchwork.ozlabs.org/project/linux-pci/list/?series=124488
> + bus-range = <0x0 0xff>;
> + ranges = <0x81000000 0x0 0x00000000 0x80 0x00010000 0x0
> 0x00010000 /* downstream I/O */
> + 0x82000000 0x0 0x40000000 0x80 0x40000000 0x0
> 0x40000000>; /* non-prefetchable memory */
> + msi-parent = <&its>;
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 7>;
> + interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 109
> IRQ_TYPE_LEVEL_HIGH>,
> + <0000 0 0 2 &gic 0 0 GIC_SPI 110
> IRQ_TYPE_LEVEL_HIGH>,
> + <0000 0 0 3 &gic 0 0 GIC_SPI 111
> IRQ_TYPE_LEVEL_HIGH>,
> + <0000 0 0 4 &gic 0 0 GIC_SPI 112
> IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> +
> + pcie@3500000 {
> + compatible = "fsl,ls1028a-pcie";
> + reg = <0x00 0x03500000 0x0 0x00100000 /* controller
> registers */
> + 0x88 0x00000000 0x0 0x00002000>; /* configuration
> space */
> + reg-names = "regs", "config";
> + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "pme", "aer";
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + dma-coherent;
> + num-lanes = <4>;
Ditto
> + bus-range = <0x0 0xff>;
> + ranges = <0x81000000 0x0 0x00000000 0x88 0x00010000 0x0
> 0x00010000 /* downstream I/O */
> + 0x82000000 0x0 0x40000000 0x88 0x40000000 0x0
> 0x40000000>; /* non-prefetchable memory */
> + msi-parent = <&its>;
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 7>;
> + interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 114
> IRQ_TYPE_LEVEL_HIGH>,
> + <0000 0 0 2 &gic 0 0 GIC_SPI 115
> IRQ_TYPE_LEVEL_HIGH>,
> + <0000 0 0 3 &gic 0 0 GIC_SPI 116
> IRQ_TYPE_LEVEL_HIGH>,
> + <0000 0 0 4 &gic 0 0 GIC_SPI 117
> IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> +
> pcie@1f0000000 { /* Integrated Endpoint Root Complex */
> compatible = "pci-host-ecam-generic";
> reg = <0x01 0xf0000000 0x0 0x100000>;
> --
> 2.9.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCHv3 3/3] PCI: layerscape: Add LS1028a support
2019-08-06 6:15 [PATCHv3 1/3] dt-bindings: pci: layerscape-pci: add compatible strings "fsl, ls1028a-pcie" Xiaowei Bao
2019-08-06 6:15 ` [PATCHv3 2/3] arm64: dts: ls1028a: Add PCIe controller DT nodes Xiaowei Bao
@ 2019-08-06 6:15 ` Xiaowei Bao
2019-08-21 19:26 ` [PATCHv3 1/3] dt-bindings: pci: layerscape-pci: add compatible strings "fsl,ls1028a-pcie" Rob Herring
2 siblings, 0 replies; 5+ messages in thread
From: Xiaowei Bao @ 2019-08-06 6:15 UTC (permalink / raw)
To: bhelgaas, robh+dt, mark.rutland, shawnguo, leoyang.li, kishon,
lorenzo.pieralisi, arnd, gregkh, minghuan.Lian, mingkai.hu,
zhiqiang.hou, roy.zang, kstewart, pombredanne, shawn.lin,
linux-pci, devicetree, linux-kernel, linux-arm-kernel,
linuxppc-dev
Cc: Hou Zhiqiang, Xiaowei Bao
Add support for the LS1028a PCIe controller.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
---
v2:
- no change.
v3:
- Reuse the ls2088 driver data structurt.
drivers/pci/controller/dwc/pci-layerscape.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/pci/controller/dwc/pci-layerscape.c b/drivers/pci/controller/dwc/pci-layerscape.c
index 3a5fa26..f24f79a 100644
--- a/drivers/pci/controller/dwc/pci-layerscape.c
+++ b/drivers/pci/controller/dwc/pci-layerscape.c
@@ -263,6 +263,7 @@ static const struct ls_pcie_drvdata ls2088_drvdata = {
static const struct of_device_id ls_pcie_of_match[] = {
{ .compatible = "fsl,ls1012a-pcie", .data = &ls1046_drvdata },
{ .compatible = "fsl,ls1021a-pcie", .data = &ls1021_drvdata },
+ { .compatible = "fsl,ls1028a-pcie", .data = &ls2088_drvdata },
{ .compatible = "fsl,ls1043a-pcie", .data = &ls1043_drvdata },
{ .compatible = "fsl,ls1046a-pcie", .data = &ls1046_drvdata },
{ .compatible = "fsl,ls2080a-pcie", .data = &ls2080_drvdata },
--
2.9.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 5+ messages in thread* Re: [PATCHv3 1/3] dt-bindings: pci: layerscape-pci: add compatible strings "fsl,ls1028a-pcie"
2019-08-06 6:15 [PATCHv3 1/3] dt-bindings: pci: layerscape-pci: add compatible strings "fsl, ls1028a-pcie" Xiaowei Bao
2019-08-06 6:15 ` [PATCHv3 2/3] arm64: dts: ls1028a: Add PCIe controller DT nodes Xiaowei Bao
2019-08-06 6:15 ` [PATCHv3 3/3] PCI: layerscape: Add LS1028a support Xiaowei Bao
@ 2019-08-21 19:26 ` Rob Herring
2 siblings, 0 replies; 5+ messages in thread
From: Rob Herring @ 2019-08-21 19:26 UTC (permalink / raw)
To: Xiaowei Bao
Cc: mark.rutland, kstewart, linux-pci, shawn.lin, minghuan.Lian,
shawnguo, lorenzo.pieralisi, kishon, mingkai.hu, devicetree,
arnd, Hou Zhiqiang, robh+dt, bhelgaas, linux-arm-kernel,
roy.zang, Xiaowei Bao, gregkh, linux-kernel, leoyang.li,
pombredanne, linuxppc-dev
On Tue, 6 Aug 2019 14:15:51 +0800, Xiaowei Bao wrote:
> Add the PCIe compatible string for LS1028A
>
> Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
> ---
> v2:
> - no change.
> v3:
> - no change.
>
> Documentation/devicetree/bindings/pci/layerscape-pci.txt | 1 +
> 1 file changed, 1 insertion(+)
>
Reviewed-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 5+ messages in thread