[PATCH v2 00/11] arm64: renesas: Add r8a77961 support

[PATCH v2 00/11] arm64: renesas: Add r8a77961 support

[Geert Uytterhoeven]

	Hi all,

This patch series adds initial support for the Renesas R-Car M3-W+
(R8A77961) SoC, and for the Salvator-XS development board equipped with
this SoC.  As R-Car M3-W+ is very similar to R-Car M3-W (R8A77960), the
existing RST and SYSC drivers are updated to handle both.

To avoid confusion between R-Car M3-W and M3-W+, a new config symbol
(ARCH_R8A77960) is introduced for M3-W, to replace the old symbol
(ARCH_R8A7796) later.  The old symbol will be removed when all users in
other subsystems have been converted to use the new symbol.
The existing config symbol for M3-W SYSC is renamed to SYSC_R8A77960.

Changes compared to v1[1]:
  - Split in per-subsystem series,
  - Add Reviewed-by, Tested-by,
  - Rename SYSC_R8A7796,
  - Add ARCH_R8A77960,
  - Prepare for future removal of ARCH_R8A7796,
  - Wrap SoC-specific parts in #ifdefs.

I intend to queue this series in renesas-devel for v5.5 (except for the
local defconfig patch).
Note that arch/arm64/boot/dts/renesas/r8a77961.dtsi depends on the power
domain and clock domain indices from:
  - "[PATCH v2 5/5] dt-bindings: power: Add r8a77961 SYSC power domain
     definitions"[2],
  - "[PATCH v2 2/4] dt-bindings: clock: Add r8a77961 CPG Core Clock
     Definitions"[3],
which will be put on a branch shared by drivers and DTS.

For testing, I pushed this and all dependencies[2-5] to the
topic/r8a77961-v2 branch of my renesas-drivers git repository at
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers.git.

Thanks for your comments!

[1] "[PATCH/RFC 00/19] arm64: dts: renesas: Initial support for R-Car M3-W+"
    https://lore.kernel.org/linux-renesas-soc/20191007102332.12196-1-geert+renesas@glider.be/
[2] "[PATCH v2 0/5] dt-bindings: arm: renesas: Add core r8a77961 support"
    (https://lore.kernel.org/linux-renesas-soc/20191023122911.12166-1-geert+renesas@glider.be/)
[3] "[PATCH v2 0/4] clk: renesas: Add r8a77961 support"
    (https://lore.kernel.org/linux-renesas-soc/20191023122941.12342-1-geert+renesas@glider.be/)
[4] "[PATCH v2 0/3] pinctrl: sh-pfc: Add r8a77961 support"
    (https://lore.kernel.org/linux-renesas-soc/20191023122955.12420-1-geert+renesas@glider.be/)
[5] "[PATCH v2] dt-bindings: serial: sh-sci: Document r8a77961 bindings"
    (https://lore.kernel.org/linux-renesas-soc/20191023123010.12501-1-geert+renesas@glider.be/)

Geert Uytterhoeven (11):
  soc: renesas: Rename SYSC_R8A7796 to SYSC_R8A77960
  soc: renesas: Add ARCH_R8A77960 for existing R-Car M3-W
  soc: renesas: Add ARCH_R8A77961 for new R-Car M3-W+
  soc: renesas: Identify R-Car M3-W+
  soc: renesas: rcar-rst: Add R8A77961 support
  soc: renesas: rcar-sysc: Add R8A77961 support
  arm64: dts: renesas: Prepare for rename of ARCH_R8A7796 to
    ARCH_R8A77960
  arm64: dts: renesas: Add Renesas R8A77961 SoC support
  arm64: dts: renesas: Add support for Salvator-XS with R-Car M3-W+
  arm64: defconfig: Enable R8A77961 SoC
  [LOCAL] arm64: renesas_defconfig: Enable R8A77961 SoC

 arch/arm64/boot/dts/renesas/Makefile          |   4 +
 .../boot/dts/renesas/r8a77961-salvator-xs.dts |  31 +
 arch/arm64/boot/dts/renesas/r8a77961.dtsi     | 723 ++++++++++++++++++
 arch/arm64/configs/defconfig                  |   1 +
 arch/arm64/configs/renesas_defconfig          |   1 +
 drivers/soc/renesas/Kconfig                   |  21 +-
 drivers/soc/renesas/Makefile                  |   3 +-
 drivers/soc/renesas/r8a7796-sysc.c            |  27 +-
 drivers/soc/renesas/rcar-rst.c                |   1 +
 drivers/soc/renesas/rcar-sysc.c               |   7 +-
 drivers/soc/renesas/rcar-sysc.h               |   3 +-
 drivers/soc/renesas/renesas-soc.c             |   5 +-
 12 files changed, 807 insertions(+), 20 deletions(-)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a77961-salvator-xs.dts
 create mode 100644 arch/arm64/boot/dts/renesas/r8a77961.dtsi

-- 
2.17.1

Gr{oetje,eeting}s,

						Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
							    -- Linus Torvalds

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 01/11] soc: renesas: Rename SYSC_R8A7796 to SYSC_R8A77960

[Geert Uytterhoeven]

Rename CONFIG_SYSC_R8A7796 for R-Car M3-W (R8A77960) to
CONFIG_SYSC_R8A77960, to avoid confusion with R-Car M3-W+ (R8A77961),
which will use CONFIG_SYSC_R8A77961.

Rename r8a7796_sysc_info and r8a7796_sysc_init for consistency.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
v2:
  - New.
---
 drivers/soc/renesas/Kconfig        | 4 ++--
 drivers/soc/renesas/Makefile       | 2 +-
 drivers/soc/renesas/r8a7796-sysc.c | 8 ++++----
 drivers/soc/renesas/rcar-sysc.c    | 4 ++--
 drivers/soc/renesas/rcar-sysc.h    | 2 +-
 5 files changed, 10 insertions(+), 10 deletions(-)

diff --git a/drivers/soc/renesas/Kconfig b/drivers/soc/renesas/Kconfig
index 3bd0c218bf30992a..328d7c409202e6a5 100644
--- a/drivers/soc/renesas/Kconfig
+++ b/drivers/soc/renesas/Kconfig
@@ -202,7 +202,7 @@ config ARCH_R8A7795
 config ARCH_R8A7796
 	bool "Renesas R-Car M3-W SoC Platform"
 	select ARCH_RCAR_GEN3
-	select SYSC_R8A7796
+	select SYSC_R8A77960
 	help
 	  This enables support for the Renesas R-Car M3-W SoC.
 
@@ -292,7 +292,7 @@ config SYSC_R8A7795
 	bool "R-Car H3 System Controller support" if COMPILE_TEST
 	select SYSC_RCAR
 
-config SYSC_R8A7796
+config SYSC_R8A77960
 	bool "R-Car M3-W System Controller support" if COMPILE_TEST
 	select SYSC_RCAR
 
diff --git a/drivers/soc/renesas/Makefile b/drivers/soc/renesas/Makefile
index e99dc37ea1209444..d8a7cfdc9c9cc45f 100644
--- a/drivers/soc/renesas/Makefile
+++ b/drivers/soc/renesas/Makefile
@@ -15,7 +15,7 @@ obj-$(CONFIG_SYSC_R8A7791)	+= r8a7791-sysc.o
 obj-$(CONFIG_SYSC_R8A7792)	+= r8a7792-sysc.o
 obj-$(CONFIG_SYSC_R8A7794)	+= r8a7794-sysc.o
 obj-$(CONFIG_SYSC_R8A7795)	+= r8a7795-sysc.o
-obj-$(CONFIG_SYSC_R8A7796)	+= r8a7796-sysc.o
+obj-$(CONFIG_SYSC_R8A77960)	+= r8a7796-sysc.o
 obj-$(CONFIG_SYSC_R8A77965)	+= r8a77965-sysc.o
 obj-$(CONFIG_SYSC_R8A77970)	+= r8a77970-sysc.o
 obj-$(CONFIG_SYSC_R8A77980)	+= r8a77980-sysc.o
diff --git a/drivers/soc/renesas/r8a7796-sysc.c b/drivers/soc/renesas/r8a7796-sysc.c
index d374622a667bbfbd..c2accd8d76686ef4 100644
--- a/drivers/soc/renesas/r8a7796-sysc.c
+++ b/drivers/soc/renesas/r8a7796-sysc.c
@@ -47,16 +47,16 @@ static const struct soc_device_attribute r8a7796es1[] __initconst = {
 	{ /* sentinel */ }
 };
 
-static int __init r8a7796_sysc_init(void)
+static int __init r8a77960_sysc_init(void)
 {
 	if (soc_device_match(r8a7796es1))
-		r8a7796_sysc_info.extmask_val = 0;
+		r8a77960_sysc_info.extmask_val = 0;
 
 	return 0;
 }
 
-struct rcar_sysc_info r8a7796_sysc_info __initdata = {
-	.init = r8a7796_sysc_init,
+struct rcar_sysc_info r8a77960_sysc_info __initdata = {
+	.init = r8a77960_sysc_init,
 	.areas = r8a7796_areas,
 	.num_areas = ARRAY_SIZE(r8a7796_areas),
 	.extmask_offs = 0x2f8,
diff --git a/drivers/soc/renesas/rcar-sysc.c b/drivers/soc/renesas/rcar-sysc.c
index d4f2ed52b2b363be..5f17b12e9d0c6a87 100644
--- a/drivers/soc/renesas/rcar-sysc.c
+++ b/drivers/soc/renesas/rcar-sysc.c
@@ -313,8 +313,8 @@ static const struct of_device_id rcar_sysc_matches[] __initconst = {
 #ifdef CONFIG_SYSC_R8A7795
 	{ .compatible = "renesas,r8a7795-sysc", .data = &r8a7795_sysc_info },
 #endif
-#ifdef CONFIG_SYSC_R8A7796
-	{ .compatible = "renesas,r8a7796-sysc", .data = &r8a7796_sysc_info },
+#ifdef CONFIG_SYSC_R8A77960
+	{ .compatible = "renesas,r8a7796-sysc", .data = &r8a77960_sysc_info },
 #endif
 #ifdef CONFIG_SYSC_R8A77965
 	{ .compatible = "renesas,r8a77965-sysc", .data = &r8a77965_sysc_info },
diff --git a/drivers/soc/renesas/rcar-sysc.h b/drivers/soc/renesas/rcar-sysc.h
index e4c9854f5dc00492..379a6b2661ebce87 100644
--- a/drivers/soc/renesas/rcar-sysc.h
+++ b/drivers/soc/renesas/rcar-sysc.h
@@ -61,7 +61,7 @@ extern const struct rcar_sysc_info r8a7791_sysc_info;
 extern const struct rcar_sysc_info r8a7792_sysc_info;
 extern const struct rcar_sysc_info r8a7794_sysc_info;
 extern struct rcar_sysc_info r8a7795_sysc_info;
-extern struct rcar_sysc_info r8a7796_sysc_info;
+extern struct rcar_sysc_info r8a77960_sysc_info;
 extern const struct rcar_sysc_info r8a77965_sysc_info;
 extern const struct rcar_sysc_info r8a77970_sysc_info;
 extern const struct rcar_sysc_info r8a77980_sysc_info;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 02/11] soc: renesas: Add ARCH_R8A77960 for existing R-Car M3-W

[Geert Uytterhoeven]

Add CONFIG_ARCH_R8A77960 as a new config symbol for R-Car M3-W
(R8A77960), to replace CONFIG_ARCH_R8A7796, and avoid confusion with
R-Car M3-W+ (R8A77961), which will use CONFIG_ARCH_R8A77961.

Note that for now, CONFIG_ARCH_R8A7796 is retained, and just selects
CONFIG_ARCH_R8A77960.  This relaxes dependencies of other subsystems on
the SoC configuration symbol, and provides a smooth transition path for
config files through "make oldconfig".

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
v2:
  - New.
---
 drivers/soc/renesas/Kconfig       | 8 ++++++--
 drivers/soc/renesas/renesas-soc.c | 2 +-
 2 files changed, 7 insertions(+), 3 deletions(-)

diff --git a/drivers/soc/renesas/Kconfig b/drivers/soc/renesas/Kconfig
index 328d7c409202e6a5..ce8e86a037d1d704 100644
--- a/drivers/soc/renesas/Kconfig
+++ b/drivers/soc/renesas/Kconfig
@@ -199,10 +199,14 @@ config ARCH_R8A7795
 	help
 	  This enables support for the Renesas R-Car H3 SoC.
 
-config ARCH_R8A7796
-	bool "Renesas R-Car M3-W SoC Platform"
+config ARCH_R8A77960
+	bool
 	select ARCH_RCAR_GEN3
 	select SYSC_R8A77960
+
+config ARCH_R8A7796
+	bool "Renesas R-Car M3-W SoC Platform"
+	select ARCH_R8A77960
 	help
 	  This enables support for the Renesas R-Car M3-W SoC.
 
diff --git a/drivers/soc/renesas/renesas-soc.c b/drivers/soc/renesas/renesas-soc.c
index 45135bc88e277d34..319e47bb1d99cfcf 100644
--- a/drivers/soc/renesas/renesas-soc.c
+++ b/drivers/soc/renesas/renesas-soc.c
@@ -262,7 +262,7 @@ static const struct of_device_id renesas_socs[] __initconst = {
 #ifdef CONFIG_ARCH_R8A7795
 	{ .compatible = "renesas,r8a7795",	.data = &soc_rcar_h3 },
 #endif
-#ifdef CONFIG_ARCH_R8A7796
+#ifdef CONFIG_ARCH_R8A77960
 	{ .compatible = "renesas,r8a7796",	.data = &soc_rcar_m3_w },
 #endif
 #ifdef CONFIG_ARCH_R8A77965
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 03/11] soc: renesas: Add ARCH_R8A77961 for new R-Car M3-W+

[Geert Uytterhoeven]

Add CONFIG_ARCH_R8A77961 as a configuration symbol for the new Renesas
R-Car M3-W+ (R8A77961) SoC.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
---
v2:
  - Add Reviewed-by, Tested-by,
  - Reword.
---
 drivers/soc/renesas/Kconfig | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/soc/renesas/Kconfig b/drivers/soc/renesas/Kconfig
index ce8e86a037d1d704..7b00daa290924445 100644
--- a/drivers/soc/renesas/Kconfig
+++ b/drivers/soc/renesas/Kconfig
@@ -210,6 +210,12 @@ config ARCH_R8A7796
 	help
 	  This enables support for the Renesas R-Car M3-W SoC.
 
+config ARCH_R8A77961
+	bool "Renesas R-Car M3-W+ SoC Platform"
+	select ARCH_RCAR_GEN3
+	help
+	  This enables support for the Renesas R-Car M3-W+ SoC.
+
 config ARCH_R8A77965
 	bool "Renesas R-Car M3-N SoC Platform"
 	select ARCH_RCAR_GEN3
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 04/11] soc: renesas: Identify R-Car M3-W+

[Geert Uytterhoeven]

Add support for identifying the R-Car M3-W+ (R8A77961) SoC, which shares
the Product ID Number with R-Car M3-W (R8A77960), but differs in CUT
Number (Ver. 3.0), and uses a different compatible value.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
---
v2:
  - Add Reviewed-by, Tested-by,
  - Reword.
---
 drivers/soc/renesas/renesas-soc.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/soc/renesas/renesas-soc.c b/drivers/soc/renesas/renesas-soc.c
index 319e47bb1d99cfcf..573cc6a98177ba2c 100644
--- a/drivers/soc/renesas/renesas-soc.c
+++ b/drivers/soc/renesas/renesas-soc.c
@@ -265,6 +265,9 @@ static const struct of_device_id renesas_socs[] __initconst = {
 #ifdef CONFIG_ARCH_R8A77960
 	{ .compatible = "renesas,r8a7796",	.data = &soc_rcar_m3_w },
 #endif
+#ifdef CONFIG_ARCH_R8A77961
+	{ .compatible = "renesas,r8a77961",	.data = &soc_rcar_m3_w },
+#endif
 #ifdef CONFIG_ARCH_R8A77965
 	{ .compatible = "renesas,r8a77965",	.data = &soc_rcar_m3_n },
 #endif
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 05/11] soc: renesas: rcar-rst: Add R8A77961 support

[Geert Uytterhoeven]

Add support for the Reset block in the R-Car M3-W+ (R8A77961) SoC to the
Renesas R-Car RST driver.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
---
v2:
  - Add Reviewed-by, Tested-by,
  - Reword.
---
 drivers/soc/renesas/rcar-rst.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/soc/renesas/rcar-rst.c b/drivers/soc/renesas/rcar-rst.c
index cd5592977cefc22b..14d05a070dd3ecea 100644
--- a/drivers/soc/renesas/rcar-rst.c
+++ b/drivers/soc/renesas/rcar-rst.c
@@ -59,6 +59,7 @@ static const struct of_device_id rcar_rst_matches[] __initconst = {
 	/* R-Car Gen3 */
 	{ .compatible = "renesas,r8a7795-rst", .data = &rcar_rst_gen3 },
 	{ .compatible = "renesas,r8a7796-rst", .data = &rcar_rst_gen3 },
+	{ .compatible = "renesas,r8a77961-rst", .data = &rcar_rst_gen3 },
 	{ .compatible = "renesas,r8a77965-rst", .data = &rcar_rst_gen3 },
 	{ .compatible = "renesas,r8a77970-rst", .data = &rcar_rst_gen3 },
 	{ .compatible = "renesas,r8a77980-rst", .data = &rcar_rst_gen3 },
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 06/11] soc: renesas: rcar-sysc: Add R8A77961 support

[Geert Uytterhoeven]

Add support for the power areas in the Renesas R-Car M3-W+ (R8A77961)
SoC to the R-Car System Controller driver.

R-Car M3-W+ (aka R-Car M3-W ES3.0) is very similar to R-Car
M3-W (R8A77960), which allows for both SoCs to share a driver:
  - R-Car M3-W+ lacks the A2VC power area, so its area must be
    nullified,
  - The existing support for the SYSCEXTMASK register added in commit
    9bd645af9d2a49ac ("soc: renesas: r8a7796-sysc: Fix power request
    conflicts") applies to ES3.0 and later only.
    As R-Car M3-W+ uses a different compatible value, differentiate
    based on that, instead of on the ES version.

Based on a patch in the BSP by Dien Pham <dien.pham.ry@renesas.com>.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
---
v2:
  - Add Reviewed-by, Tested-by,
  - Move r8a7796_sysc_info rename to a prerequisite patch,
  - Wrap SoC-specific parts in #ifdefs.
---
 drivers/soc/renesas/Kconfig        |  5 +++++
 drivers/soc/renesas/Makefile       |  1 +
 drivers/soc/renesas/r8a7796-sysc.c | 27 +++++++++++++++------------
 drivers/soc/renesas/rcar-sysc.c    |  3 +++
 drivers/soc/renesas/rcar-sysc.h    |  3 ++-
 5 files changed, 26 insertions(+), 13 deletions(-)

diff --git a/drivers/soc/renesas/Kconfig b/drivers/soc/renesas/Kconfig
index 7b00daa290924445..f93492b72c04e237 100644
--- a/drivers/soc/renesas/Kconfig
+++ b/drivers/soc/renesas/Kconfig
@@ -213,6 +213,7 @@ config ARCH_R8A7796
 config ARCH_R8A77961
 	bool "Renesas R-Car M3-W+ SoC Platform"
 	select ARCH_RCAR_GEN3
+	select SYSC_R8A77961
 	help
 	  This enables support for the Renesas R-Car M3-W+ SoC.
 
@@ -306,6 +307,10 @@ config SYSC_R8A77960
 	bool "R-Car M3-W System Controller support" if COMPILE_TEST
 	select SYSC_RCAR
 
+config SYSC_R8A77961
+	bool "R-Car M3-W+ System Controller support" if COMPILE_TEST
+	select SYSC_RCAR
+
 config SYSC_R8A77965
 	bool "R-Car M3-N System Controller support" if COMPILE_TEST
 	select SYSC_RCAR
diff --git a/drivers/soc/renesas/Makefile b/drivers/soc/renesas/Makefile
index d8a7cfdc9c9cc45f..e595c3c3bd104122 100644
--- a/drivers/soc/renesas/Makefile
+++ b/drivers/soc/renesas/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_SYSC_R8A7792)	+= r8a7792-sysc.o
 obj-$(CONFIG_SYSC_R8A7794)	+= r8a7794-sysc.o
 obj-$(CONFIG_SYSC_R8A7795)	+= r8a7795-sysc.o
 obj-$(CONFIG_SYSC_R8A77960)	+= r8a7796-sysc.o
+obj-$(CONFIG_SYSC_R8A77961)	+= r8a7796-sysc.o
 obj-$(CONFIG_SYSC_R8A77965)	+= r8a77965-sysc.o
 obj-$(CONFIG_SYSC_R8A77970)	+= r8a77970-sysc.o
 obj-$(CONFIG_SYSC_R8A77980)	+= r8a77980-sysc.o
diff --git a/drivers/soc/renesas/r8a7796-sysc.c b/drivers/soc/renesas/r8a7796-sysc.c
index c2accd8d76686ef4..471bd5b3b6ada18d 100644
--- a/drivers/soc/renesas/r8a7796-sysc.c
+++ b/drivers/soc/renesas/r8a7796-sysc.c
@@ -1,19 +1,19 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Renesas R-Car M3-W System Controller
+ * Renesas R-Car M3-W/W+ System Controller
  *
  * Copyright (C) 2016 Glider bvba
+ * Copyright (C) 2018-2019 Renesas Electronics Corporation
  */
 
 #include <linux/bits.h>
 #include <linux/kernel.h>
-#include <linux/sys_soc.h>
 
 #include <dt-bindings/power/r8a7796-sysc.h>
 
 #include "rcar-sysc.h"
 
-static const struct rcar_sysc_area r8a7796_areas[] __initconst = {
+static struct rcar_sysc_area r8a7796_areas[] __initdata = {
 	{ "always-on",	    0, 0, R8A7796_PD_ALWAYS_ON,	-1, PD_ALWAYS_ON },
 	{ "ca57-scu",	0x1c0, 0, R8A7796_PD_CA57_SCU,	R8A7796_PD_ALWAYS_ON,
 	  PD_SCU },
@@ -41,24 +41,27 @@ static const struct rcar_sysc_area r8a7796_areas[] __initconst = {
 };
 
 
-/* Fixups for R-Car M3-W ES1.x revision */
-static const struct soc_device_attribute r8a7796es1[] __initconst = {
-	{ .soc_id = "r8a7796", .revision = "ES1.*" },
-	{ /* sentinel */ }
+#ifdef CONFIG_SYSC_R8A77960
+const struct rcar_sysc_info r8a77960_sysc_info __initconst = {
+	.areas = r8a7796_areas,
+	.num_areas = ARRAY_SIZE(r8a7796_areas),
 };
+#endif /* CONFIG_SYSC_R8A77960 */
 
-static int __init r8a77960_sysc_init(void)
+#ifdef CONFIG_SYSC_R8A77961
+static int __init r8a77961_sysc_init(void)
 {
-	if (soc_device_match(r8a7796es1))
-		r8a77960_sysc_info.extmask_val = 0;
+	rcar_sysc_nullify(r8a7796_areas, ARRAY_SIZE(r8a7796_areas),
+			  R8A7796_PD_A2VC0);
 
 	return 0;
 }
 
-struct rcar_sysc_info r8a77960_sysc_info __initdata = {
-	.init = r8a77960_sysc_init,
+const struct rcar_sysc_info r8a77961_sysc_info __initconst = {
+	.init = r8a77961_sysc_init,
 	.areas = r8a7796_areas,
 	.num_areas = ARRAY_SIZE(r8a7796_areas),
 	.extmask_offs = 0x2f8,
 	.extmask_val = BIT(0),
 };
+#endif /* CONFIG_SYSC_R8A77961 */
diff --git a/drivers/soc/renesas/rcar-sysc.c b/drivers/soc/renesas/rcar-sysc.c
index 5f17b12e9d0c6a87..f0b291e02b8aba1b 100644
--- a/drivers/soc/renesas/rcar-sysc.c
+++ b/drivers/soc/renesas/rcar-sysc.c
@@ -316,6 +316,9 @@ static const struct of_device_id rcar_sysc_matches[] __initconst = {
 #ifdef CONFIG_SYSC_R8A77960
 	{ .compatible = "renesas,r8a7796-sysc", .data = &r8a77960_sysc_info },
 #endif
+#ifdef CONFIG_SYSC_R8A77961
+	{ .compatible = "renesas,r8a77961-sysc", .data = &r8a77961_sysc_info },
+#endif
 #ifdef CONFIG_SYSC_R8A77965
 	{ .compatible = "renesas,r8a77965-sysc", .data = &r8a77965_sysc_info },
 #endif
diff --git a/drivers/soc/renesas/rcar-sysc.h b/drivers/soc/renesas/rcar-sysc.h
index 379a6b2661ebce87..8d074489fba96821 100644
--- a/drivers/soc/renesas/rcar-sysc.h
+++ b/drivers/soc/renesas/rcar-sysc.h
@@ -61,7 +61,8 @@ extern const struct rcar_sysc_info r8a7791_sysc_info;
 extern const struct rcar_sysc_info r8a7792_sysc_info;
 extern const struct rcar_sysc_info r8a7794_sysc_info;
 extern struct rcar_sysc_info r8a7795_sysc_info;
-extern struct rcar_sysc_info r8a77960_sysc_info;
+extern const struct rcar_sysc_info r8a77960_sysc_info;
+extern const struct rcar_sysc_info r8a77961_sysc_info;
 extern const struct rcar_sysc_info r8a77965_sysc_info;
 extern const struct rcar_sysc_info r8a77970_sysc_info;
 extern const struct rcar_sysc_info r8a77980_sysc_info;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 07/11] arm64: dts: renesas: Prepare for rename of ARCH_R8A7796 to ARCH_R8A77960

[Geert Uytterhoeven]

CONFIG_ARCH_R8A7796 for R-Car M3-W (R8A77960) will be renamed to
CONFIG_ARCH_R8A77960, to avoid confusion with R-Car M3-W+ (R8A77961),
which will use CONFIG_ARCH_R8A77961.

Relax dependencies by handling both symbols.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
v2:
  - New.
---
 arch/arm64/boot/dts/renesas/Makefile | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index 72234e1709a9f19c..937a3e4c3fadebb3 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -12,6 +12,9 @@ dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-es1-h3ulcb-kf.dtb
 dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-x.dtb r8a7796-m3ulcb.dtb
 dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-m3ulcb-kf.dtb
 dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-xs.dtb
+dtb-$(CONFIG_ARCH_R8A77960) += r8a7796-salvator-x.dtb r8a7796-m3ulcb.dtb
+dtb-$(CONFIG_ARCH_R8A77960) += r8a7796-m3ulcb-kf.dtb
+dtb-$(CONFIG_ARCH_R8A77960) += r8a7796-salvator-xs.dtb
 dtb-$(CONFIG_ARCH_R8A77965) += r8a77965-salvator-x.dtb r8a77965-salvator-xs.dtb
 dtb-$(CONFIG_ARCH_R8A77965) += r8a77965-m3nulcb.dtb
 dtb-$(CONFIG_ARCH_R8A77965) += r8a77965-m3nulcb-kf.dtb
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 08/11] arm64: dts: renesas: Add Renesas R8A77961 SoC support

[Geert Uytterhoeven]

Add initial support for the Renesas R-Car M3-W+ (R8A77961) SoC.

This includes:
  - Cortex-A57 and Cortex-A53 CPU cores
    (incl. L2 caches and power state definitions),
  - Power Management Unit,
  - PSCI firmware,
  - Pin Function Controller,
  - Clock, Reset, System, and Interrupt Controllers,
  - SCIF2 serial console,
  - Product Register,
  - ARM Architectured Timer,
and various placeholders to allow to use salvator-xs.dtsi.

Based on r8a7796.dtsi.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
---
v2:
  - Add Reviewed-by, Tested-by.
---
 arch/arm64/boot/dts/renesas/r8a77961.dtsi | 723 ++++++++++++++++++++++
 1 file changed, 723 insertions(+)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a77961.dtsi

diff --git a/arch/arm64/boot/dts/renesas/r8a77961.dtsi b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
new file mode 100644
index 0000000000000000..64466c86b698826d
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
@@ -0,0 +1,723 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the R-Car M3-W+ (R8A77961) SoC
+ *
+ * Copyright (C) 2016-2017 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/clock/r8a77961-cpg-mssr.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/r8a77961-sysc.h>
+
+#define CPG_AUDIO_CLK_I		R8A77961_CLK_S0D4
+
+/ {
+	compatible = "renesas,r8a77961";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	/*
+	 * The external audio clocks are configured as 0 Hz fixed frequency
+	 * clocks by default.
+	 * Boards that provide audio clocks should override them.
+	 */
+	audio_clk_a: audio_clk_a {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	audio_clk_b: audio_clk_b {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	audio_clk_c: audio_clk_c {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	/* External CAN clock - to be overridden by boards that provide it */
+	can_clk: can {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	cluster0_opp: opp_table0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-500000000 {
+			opp-hz = /bits/ 64 <500000000>;
+			opp-microvolt = <820000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <820000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-1500000000 {
+			opp-hz = /bits/ 64 <1500000000>;
+			opp-microvolt = <820000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-1600000000 {
+			opp-hz = /bits/ 64 <1600000000>;
+			opp-microvolt = <900000>;
+			clock-latency-ns = <300000>;
+			turbo-mode;
+		};
+		opp-1700000000 {
+			opp-hz = /bits/ 64 <1700000000>;
+			opp-microvolt = <900000>;
+			clock-latency-ns = <300000>;
+			turbo-mode;
+		};
+		opp-1800000000 {
+			opp-hz = /bits/ 64 <1800000000>;
+			opp-microvolt = <960000>;
+			clock-latency-ns = <300000>;
+			turbo-mode;
+		};
+	};
+
+	cluster1_opp: opp_table1 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <820000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <820000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <820000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-1300000000 {
+			opp-hz = /bits/ 64 <1300000000>;
+			opp-microvolt = <820000>;
+			clock-latency-ns = <300000>;
+			turbo-mode;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&a57_0>;
+				};
+				core1 {
+					cpu = <&a57_1>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&a53_0>;
+				};
+				core1 {
+					cpu = <&a53_1>;
+				};
+				core2 {
+					cpu = <&a53_2>;
+				};
+				core3 {
+					cpu = <&a53_3>;
+				};
+			};
+		};
+
+		a57_0: cpu@0 {
+			compatible = "arm,cortex-a57";
+			reg = <0x0>;
+			device_type = "cpu";
+			power-domains = <&sysc R8A77961_PD_CA57_CPU0>;
+			next-level-cache = <&L2_CA57>;
+			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			dynamic-power-coefficient = <854>;
+			clocks = <&cpg CPG_CORE R8A77961_CLK_Z>;
+			operating-points-v2 = <&cluster0_opp>;
+			capacity-dmips-mhz = <1024>;
+			#cooling-cells = <2>;
+		};
+
+		a57_1: cpu@1 {
+			compatible = "arm,cortex-a57";
+			reg = <0x1>;
+			device_type = "cpu";
+			power-domains = <&sysc R8A77961_PD_CA57_CPU1>;
+			next-level-cache = <&L2_CA57>;
+			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&cpg CPG_CORE R8A77961_CLK_Z>;
+			operating-points-v2 = <&cluster0_opp>;
+			capacity-dmips-mhz = <1024>;
+			#cooling-cells = <2>;
+		};
+
+		a53_0: cpu@100 {
+			compatible = "arm,cortex-a53";
+			reg = <0x100>;
+			device_type = "cpu";
+			power-domains = <&sysc R8A77961_PD_CA53_CPU0>;
+			next-level-cache = <&L2_CA53>;
+			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_1>;
+			#cooling-cells = <2>;
+			dynamic-power-coefficient = <277>;
+			clocks = <&cpg CPG_CORE R8A77961_CLK_Z2>;
+			operating-points-v2 = <&cluster1_opp>;
+			capacity-dmips-mhz = <535>;
+		};
+
+		a53_1: cpu@101 {
+			compatible = "arm,cortex-a53";
+			reg = <0x101>;
+			device_type = "cpu";
+			power-domains = <&sysc R8A77961_PD_CA53_CPU1>;
+			next-level-cache = <&L2_CA53>;
+			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_1>;
+			clocks = <&cpg CPG_CORE R8A77961_CLK_Z2>;
+			operating-points-v2 = <&cluster1_opp>;
+			capacity-dmips-mhz = <535>;
+		};
+
+		a53_2: cpu@102 {
+			compatible = "arm,cortex-a53";
+			reg = <0x102>;
+			device_type = "cpu";
+			power-domains = <&sysc R8A77961_PD_CA53_CPU2>;
+			next-level-cache = <&L2_CA53>;
+			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_1>;
+			clocks = <&cpg CPG_CORE R8A77961_CLK_Z2>;
+			operating-points-v2 = <&cluster1_opp>;
+			capacity-dmips-mhz = <535>;
+		};
+
+		a53_3: cpu@103 {
+			compatible = "arm,cortex-a53";
+			reg = <0x103>;
+			device_type = "cpu";
+			power-domains = <&sysc R8A77961_PD_CA53_CPU3>;
+			next-level-cache = <&L2_CA53>;
+			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_1>;
+			clocks = <&cpg CPG_CORE R8A77961_CLK_Z2>;
+			operating-points-v2 = <&cluster1_opp>;
+			capacity-dmips-mhz = <535>;
+		};
+
+		L2_CA57: cache-controller-0 {
+			compatible = "cache";
+			power-domains = <&sysc R8A77961_PD_CA57_SCU>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		L2_CA53: cache-controller-1 {
+			compatible = "cache";
+			power-domains = <&sysc R8A77961_PD_CA53_SCU>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		idle-states {
+			entry-method = "psci";
+
+			CPU_SLEEP_0: cpu-sleep-0 {
+				compatible = "arm,idle-state";
+				arm,psci-suspend-param = <0x0010000>;
+				local-timer-stop;
+				entry-latency-us = <400>;
+				exit-latency-us = <500>;
+				min-residency-us = <4000>;
+			};
+
+			CPU_SLEEP_1: cpu-sleep-1 {
+				compatible = "arm,idle-state";
+				arm,psci-suspend-param = <0x0010000>;
+				local-timer-stop;
+				entry-latency-us = <700>;
+				exit-latency-us = <700>;
+				min-residency-us = <5000>;
+			};
+		};
+	};
+
+	extal_clk: extal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board */
+		clock-frequency = <0>;
+	};
+
+	extalr_clk: extalr {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board */
+		clock-frequency = <0>;
+	};
+
+	/* External PCIe clock - can be overridden by the board */
+	pcie_bus_clk: pcie_bus {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	pmu_a53 {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts-extended = <&gic GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&a53_0>, <&a53_1>, <&a53_2>, <&a53_3>;
+	};
+
+	pmu_a57 {
+		compatible = "arm,cortex-a57-pmu";
+		interrupts-extended = <&gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&a57_0>, <&a57_1>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0", "arm,psci-0.2";
+		method = "smc";
+	};
+
+	/* External SCIF clock - to be overridden by boards that provide it */
+	scif_clk: scif {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		rwdt: watchdog@e6020000 {
+			reg = <0 0xe6020000 0 0x0c>;
+			/* placeholder */
+		};
+
+		gpio2: gpio@e6052000 {
+			reg = <0 0xe6052000 0 0x50>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			/* placeholder */
+		};
+
+		gpio3: gpio@e6053000 {
+			reg = <0 0xe6053000 0 0x50>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			/* placeholder */
+		};
+
+		gpio4: gpio@e6054000 {
+			reg = <0 0xe6054000 0 0x50>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			/* placeholder */
+		};
+
+		gpio5: gpio@e6055000 {
+			reg = <0 0xe6055000 0 0x50>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			/* placeholder */
+		};
+
+		gpio6: gpio@e6055400 {
+			reg = <0 0xe6055400 0 0x50>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			/* placeholder */
+		};
+
+		pfc: pin-controller@e6060000 {
+			compatible = "renesas,pfc-r8a77961";
+			reg = <0 0xe6060000 0 0x50c>;
+		};
+
+		cpg: clock-controller@e6150000 {
+			compatible = "renesas,r8a77961-cpg-mssr";
+			reg = <0 0xe6150000 0 0x1000>;
+			clocks = <&extal_clk>, <&extalr_clk>;
+			clock-names = "extal", "extalr";
+			#clock-cells = <2>;
+			#power-domain-cells = <0>;
+			#reset-cells = <1>;
+		};
+
+		rst: reset-controller@e6160000 {
+			compatible = "renesas,r8a77961-rst";
+			reg = <0 0xe6160000 0 0x0200>;
+		};
+
+		sysc: system-controller@e6180000 {
+			compatible = "renesas,r8a77961-sysc";
+			reg = <0 0xe6180000 0 0x0400>;
+			#power-domain-cells = <1>;
+		};
+
+		intc_ex: interrupt-controller@e61c0000 {
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			reg = <0 0xe61c0000 0 0x200>;
+			/* placeholder */
+		};
+
+		i2c2: i2c@e6510000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0xe6510000 0 0x40>;
+			/* placeholder */
+		};
+
+		i2c4: i2c@e66d8000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0xe66d8000 0 0x40>;
+			/* placeholder */
+		};
+
+		i2c_dvfs: i2c@e60b0000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0xe60b0000 0 0x425>;
+			/* placeholder */
+		};
+
+		hscif1: serial@e6550000 {
+			reg = <0 0xe6550000 0 0x60>;
+			/* placeholder */
+		};
+
+		hsusb: usb@e6590000 {
+			reg = <0 0xe6590000 0 0x200>;
+			/* placeholder */
+		};
+
+		usb3_phy0: usb-phy@e65ee000 {
+			reg = <0 0xe65ee000 0 0x90>;
+			#phy-cells = <0>;
+			/* placeholder */
+		};
+
+		avb: ethernet@e6800000 {
+			reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			/* placeholder */
+		};
+
+		pwm1: pwm@e6e31000 {
+			reg = <0 0xe6e31000 0 8>;
+			#pwm-cells = <2>;
+			/* placeholder */
+		};
+
+		scif1: serial@e6e68000 {
+			reg = <0 0xe6e68000 0 64>;
+			/* placeholder */
+		};
+
+		scif2: serial@e6e88000 {
+			compatible = "renesas,scif-r8a77961",
+				     "renesas,rcar-gen3-scif", "renesas,scif";
+			reg = <0 0xe6e88000 0 64>;
+			interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 310>,
+				 <&cpg CPG_CORE R8A77961_CLK_S3D1>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
+			resets = <&cpg 310>;
+			status = "disabled";
+		};
+
+		vin0: video@e6ef0000 {
+			reg = <0 0xe6ef0000 0 0x1000>;
+			/* placeholder */
+		};
+
+		vin1: video@e6ef1000 {
+			reg = <0 0xe6ef1000 0 0x1000>;
+			/* placeholder */
+		};
+
+		vin2: video@e6ef2000 {
+			reg = <0 0xe6ef2000 0 0x1000>;
+			/* placeholder */
+		};
+
+		vin3: video@e6ef3000 {
+			reg = <0 0xe6ef3000 0 0x1000>;
+			/* placeholder */
+		};
+
+		vin4: video@e6ef4000 {
+			reg = <0 0xe6ef4000 0 0x1000>;
+			/* placeholder */
+		};
+
+		vin5: video@e6ef5000 {
+			reg = <0 0xe6ef5000 0 0x1000>;
+			/* placeholder */
+		};
+
+		vin6: video@e6ef6000 {
+			reg = <0 0xe6ef6000 0 0x1000>;
+			/* placeholder */
+		};
+
+		vin7: video@e6ef7000 {
+			reg = <0 0xe6ef7000 0 0x1000>;
+			/* placeholder */
+		};
+
+		rcar_sound: sound@ec500000 {
+			reg = <0 0xec500000 0 0x1000>, /* SCU */
+			      <0 0xec5a0000 0 0x100>,  /* ADG */
+			      <0 0xec540000 0 0x1000>, /* SSIU */
+			      <0 0xec541000 0 0x280>,  /* SSI */
+			      <0 0xec760000 0 0x200>;  /* Audio DMAC peri peri*/
+			/* placeholder */
+			rcar_sound,dvc {
+				dvc0: dvc-0 { };
+				dvc1: dvc-1 { };
+			};
+
+			rcar_sound,src {
+				src0: src-0 { };
+				src1: src-1 { };
+			};
+
+			rcar_sound,ssi {
+				ssi0: ssi-0 { };
+				ssi1: ssi-1 { };
+			};
+		};
+
+		xhci0: usb@ee000000 {
+			reg = <0 0xee000000 0 0xc00>;
+			/* placeholder */
+		};
+
+		usb3_peri0: usb@ee020000 {
+			reg = <0 0xee020000 0 0x400>;
+			/* placeholder */
+		};
+
+		ohci0: usb@ee080000 {
+			reg = <0 0xee080000 0 0x100>;
+			/* placeholder */
+		};
+
+		ohci1: usb@ee0a0000 {
+			reg = <0 0xee0a0000 0 0x100>;
+			/* placeholder */
+		};
+
+		ehci0: usb@ee080100 {
+			reg = <0 0xee080100 0 0x100>;
+			/* placeholder */
+		};
+
+		ehci1: usb@ee0a0100 {
+			reg = <0 0xee0a0100 0 0x100>;
+			/* placeholder */
+		};
+
+		usb2_phy0: usb-phy@ee080200 {
+			reg = <0 0xee080200 0 0x700>;
+			/* placeholder */
+		};
+
+		usb2_phy1: usb-phy@ee0a0200 {
+			reg = <0 0xee0a0200 0 0x700>;
+			/* placeholder */
+		};
+
+		sdhi0: sd@ee100000 {
+			reg = <0 0xee100000 0 0x2000>;
+			/* placeholder */
+		};
+
+		sdhi2: sd@ee140000 {
+			reg = <0 0xee140000 0 0x2000>;
+			/* placeholder */
+		};
+
+		sdhi3: sd@ee160000 {
+			reg = <0 0xee160000 0 0x2000>;
+			/* placeholder */
+		};
+
+		gic: interrupt-controller@f1010000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x0 0xf1010000 0 0x1000>,
+			      <0x0 0xf1020000 0 0x20000>,
+			      <0x0 0xf1040000 0 0x20000>,
+			      <0x0 0xf1060000 0 0x20000>;
+			interrupts = <GIC_PPI 9
+					(GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_HIGH)>;
+			clocks = <&cpg CPG_MOD 408>;
+			clock-names = "clk";
+			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
+			resets = <&cpg 408>;
+		};
+
+		pciec0: pcie@fe000000 {
+			reg = <0 0xfe000000 0 0x80000>;
+			/* placeholder */
+		};
+
+		pciec1: pcie@ee800000 {
+			reg = <0 0xee800000 0 0x80000>;
+			/* placeholder */
+		};
+
+		csi20: csi2@fea80000 {
+			reg = <0 0xfea80000 0 0x10000>;
+			/* placeholder */
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+			};
+		};
+
+		csi40: csi2@feaa0000 {
+			reg = <0 0xfeaa0000 0 0x10000>;
+			/* placeholder */
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <1>;
+				};
+			};
+		};
+
+		hdmi0: hdmi@fead0000 {
+			reg = <0 0xfead0000 0 0x10000>;
+			/* placeholder */
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+				};
+				port@1 {
+					reg = <1>;
+				};
+				port@2 {
+					/* HDMI sound */
+					reg = <2>;
+				};
+			};
+		};
+
+		du: display@feb00000 {
+			reg = <0 0xfeb00000 0 0x70000>;
+			/* placeholder */
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					du_out_rgb: endpoint {
+					};
+				};
+				port@1 {
+					reg = <1>;
+					du_out_hdmi0: endpoint {
+					};
+				};
+				port@2 {
+					reg = <2>;
+					du_out_lvds0: endpoint {
+					};
+				};
+			};
+		};
+
+		prr: chipid@fff00044 {
+			compatible = "renesas,prr";
+			reg = <0 0xfff00044 0 4>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	/* External USB clocks - can be overridden by the board */
+	usb3s0_clk: usb3s0 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	usb_extal_clk: usb_extal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 09/11] arm64: dts: renesas: Add support for Salvator-XS with R-Car M3-W+

[Geert Uytterhoeven]

Add initial support for the Renesas Salvator-X 2nd version development
board equipped with an R-Car M3-W+ SiP with 8 (2 x 4) GiB of RAM.

The memory map is as follows:
  - Bank0: 4GiB RAM : 0x000048000000 -> 0x000bfffffff
		      0x000480000000 -> 0x004ffffffff
  - Bank1: 4GiB RAM : 0x000600000000 -> 0x006ffffffff

Based on a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
---
v2:
  - Add Reviewed-by, Tested-by.
---
 arch/arm64/boot/dts/renesas/Makefile          |  1 +
 .../boot/dts/renesas/r8a77961-salvator-xs.dts | 31 +++++++++++++++++++
 2 files changed, 32 insertions(+)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a77961-salvator-xs.dts

diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index 937a3e4c3fadebb3..8fdbd2267384186b 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -15,6 +15,7 @@ dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-xs.dtb
 dtb-$(CONFIG_ARCH_R8A77960) += r8a7796-salvator-x.dtb r8a7796-m3ulcb.dtb
 dtb-$(CONFIG_ARCH_R8A77960) += r8a7796-m3ulcb-kf.dtb
 dtb-$(CONFIG_ARCH_R8A77960) += r8a7796-salvator-xs.dtb
+dtb-$(CONFIG_ARCH_R8A77961) += r8a77961-salvator-xs.dtb
 dtb-$(CONFIG_ARCH_R8A77965) += r8a77965-salvator-x.dtb r8a77965-salvator-xs.dtb
 dtb-$(CONFIG_ARCH_R8A77965) += r8a77965-m3nulcb.dtb
 dtb-$(CONFIG_ARCH_R8A77965) += r8a77965-m3nulcb-kf.dtb
diff --git a/arch/arm64/boot/dts/renesas/r8a77961-salvator-xs.dts b/arch/arm64/boot/dts/renesas/r8a77961-salvator-xs.dts
new file mode 100644
index 0000000000000000..4abd78ac1cd597d9
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a77961-salvator-xs.dts
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the Salvator-X 2nd version board with R-Car M3-W+
+ *
+ * Copyright (C) 2018 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r8a77961.dtsi"
+#include "salvator-xs.dtsi"
+
+/ {
+	model = "Renesas Salvator-X 2nd version board based on r8a77961";
+	compatible = "renesas,salvator-xs", "renesas,r8a77961";
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x78000000>;
+	};
+
+	memory@400000000 {
+		device_type = "memory";
+		reg = <0x4 0x80000000 0x0 0x80000000>;
+	};
+
+	memory@600000000 {
+		device_type = "memory";
+		reg = <0x6 0x00000000 0x1 0x00000000>;
+	};
+};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 10/11] arm64: defconfig: Enable R8A77961 SoC

[Geert Uytterhoeven]

Enable the Renesas R-Car M3-W+ (R8A77961) SoC in the ARM64 defconfig.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
---
v2:
  - Add Reviewed-by, Tested-by.
---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index c9adae41bac03e60..4a4e338c457e45db 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -745,6 +745,7 @@ CONFIG_ARCH_R8A774B1=y
 CONFIG_ARCH_R8A774C0=y
 CONFIG_ARCH_R8A7795=y
 CONFIG_ARCH_R8A7796=y
+CONFIG_ARCH_R8A77961=y
 CONFIG_ARCH_R8A77965=y
 CONFIG_ARCH_R8A77970=y
 CONFIG_ARCH_R8A77980=y
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH/LOCAL v2 11/11] arm64: renesas_defconfig: Enable R8A77961 SoC

[Geert Uytterhoeven]

Enable the Renesas R-Car M3-W+ (R8A77961) SoC in the ARM64
renesas_defconfig.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
---
Not intended for upstream inclusion.

v2:
  - Add Reviewed-by, Tested-by.
---
 arch/arm64/configs/renesas_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/renesas_defconfig b/arch/arm64/configs/renesas_defconfig
index 2ad65929c95b63bf..8c3a3323b1859c7d 100644
--- a/arch/arm64/configs/renesas_defconfig
+++ b/arch/arm64/configs/renesas_defconfig
@@ -287,6 +287,7 @@ CONFIG_ARCH_R8A774B1=y
 CONFIG_ARCH_R8A774C0=y
 CONFIG_ARCH_R8A7795=y
 CONFIG_ARCH_R8A7796=y
+CONFIG_ARCH_R8A77961=y
 CONFIG_ARCH_R8A77965=y
 CONFIG_ARCH_R8A77970=y
 CONFIG_ARCH_R8A77980=y
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

RE: [PATCH v2 01/11] soc: renesas: Rename SYSC_R8A7796 to SYSC_R8A77960

[Yoshihiro Shimoda]

Hi Geert-san,

> From: Geert Uytterhoeven, Sent: Wednesday, October 23, 2019 9:34 PM
> 
> Rename CONFIG_SYSC_R8A7796 for R-Car M3-W (R8A77960) to
> CONFIG_SYSC_R8A77960, to avoid confusion with R-Car M3-W+ (R8A77961),
> which will use CONFIG_SYSC_R8A77961.
> 
> Rename r8a7796_sysc_info and r8a7796_sysc_init for consistency.
> 
> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Thank you for the patch!

Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>

Best regards,
Yoshihiro Shimoda


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

RE: [PATCH v2 02/11] soc: renesas: Add ARCH_R8A77960 for existing R-Car M3-W

[Yoshihiro Shimoda]

Hi Geert-san,

> From: Geert Uytterhoeven, Sent: Wednesday, October 23, 2019 9:34 PM
> 
> Add CONFIG_ARCH_R8A77960 as a new config symbol for R-Car M3-W
> (R8A77960), to replace CONFIG_ARCH_R8A7796, and avoid confusion with
> R-Car M3-W+ (R8A77961), which will use CONFIG_ARCH_R8A77961.
> 
> Note that for now, CONFIG_ARCH_R8A7796 is retained, and just selects
> CONFIG_ARCH_R8A77960.  This relaxes dependencies of other subsystems on
> the SoC configuration symbol, and provides a smooth transition path for
> config files through "make oldconfig".
> 
> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Thank you for the patch!

Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>

Best regards,
Yoshihiro Shimoda


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

RE: [PATCH v2 07/11] arm64: dts: renesas: Prepare for rename of ARCH_R8A7796 to ARCH_R8A77960

[Yoshihiro Shimoda]

Hi Geert-san,

> From: Geert Uytterhoeven, Sent: Wednesday, October 23, 2019 9:34 PM
> 
> CONFIG_ARCH_R8A7796 for R-Car M3-W (R8A77960) will be renamed to
> CONFIG_ARCH_R8A77960, to avoid confusion with R-Car M3-W+ (R8A77961),
> which will use CONFIG_ARCH_R8A77961.
> 
> Relax dependencies by handling both symbols.
> 
> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Thank you for the patch!

Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>

Best regards,
Yoshihiro Shimoda


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel