[PATCH AUTOSEL 5.11 014/104] net: stmmac: Set FIFO sizes for ipq806x

[PATCH AUTOSEL 5.11 014/104] net: stmmac: Set FIFO sizes for ipq806x

[Sasha Levin]

From: Jonathan McDowell <noodles@earth.li>

[ Upstream commit e127906b68b49ddb3ecba39ffa36a329c48197d3 ]

Commit eaf4fac47807 ("net: stmmac: Do not accept invalid MTU values")
started using the TX FIFO size to verify what counts as a valid MTU
request for the stmmac driver.  This is unset for the ipq806x variant.
Looking at older patches for this it seems the RX + TXs buffers can be
up to 8k, so set appropriately.

(I sent this as an RFC patch in June last year, but received no replies.
I've been running with this on my hardware (a MikroTik RB3011) since
then with larger MTUs to support both the internal qca8k switch and
VLANs with no problems. Without the patch it's impossible to set the
larger MTU required to support this.)

Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c
index bf3250e0e59c..749585fe6fc9 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c
@@ -352,6 +352,8 @@ static int ipq806x_gmac_probe(struct platform_device *pdev)
 	plat_dat->bsp_priv = gmac;
 	plat_dat->fix_mac_speed = ipq806x_gmac_fix_mac_speed;
 	plat_dat->multicast_filter_bins = 0;
+	plat_dat->tx_fifo_size = 8192;
+	plat_dat->rx_fifo_size = 8192;
 
 	err = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
 	if (err)
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.11 036/104] KVM: arm64: Use BUG and BUG_ON in nVHE hyp

[Sasha Levin]

From: Andrew Scull <ascull@google.com>

[ Upstream commit f79e616f27ab6cd74deb0995a8eead3d1c9d65af ]

hyp_panic() reports the address of the panic by using ELR_EL2, but this
isn't a useful address when hyp_panic() is called directly. Replace such
direct calls with BUG() and BUG_ON() which use BRK to trigger an
exception that then goes to hyp_panic() with the correct address. Also
remove the hyp_panic() declaration from the header file to avoid
accidental misuse.

Signed-off-by: Andrew Scull <ascull@google.com>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210318143311.839894-5-ascull@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/include/asm/kvm_hyp.h   | 1 -
 arch/arm64/kvm/hyp/nvhe/hyp-main.c | 2 +-
 arch/arm64/kvm/hyp/nvhe/hyp-smp.c  | 6 ++----
 3 files changed, 3 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/include/asm/kvm_hyp.h b/arch/arm64/include/asm/kvm_hyp.h
index 32ae676236b6..fe5fc814f228 100644
--- a/arch/arm64/include/asm/kvm_hyp.h
+++ b/arch/arm64/include/asm/kvm_hyp.h
@@ -100,7 +100,6 @@ u64 __guest_enter(struct kvm_vcpu *vcpu);
 
 bool kvm_host_psci_handler(struct kvm_cpu_context *host_ctxt);
 
-void __noreturn hyp_panic(void);
 #ifdef __KVM_NVHE_HYPERVISOR__
 void __noreturn __hyp_do_panic(struct kvm_cpu_context *host_ctxt, u64 spsr,
 			       u64 elr, u64 par);
diff --git a/arch/arm64/kvm/hyp/nvhe/hyp-main.c b/arch/arm64/kvm/hyp/nvhe/hyp-main.c
index 1b8ef37bf805..2630d3bbae62 100644
--- a/arch/arm64/kvm/hyp/nvhe/hyp-main.c
+++ b/arch/arm64/kvm/hyp/nvhe/hyp-main.c
@@ -181,6 +181,6 @@ void handle_trap(struct kvm_cpu_context *host_ctxt)
 		handle_host_smc(host_ctxt);
 		break;
 	default:
-		hyp_panic();
+		BUG();
 	}
 }
diff --git a/arch/arm64/kvm/hyp/nvhe/hyp-smp.c b/arch/arm64/kvm/hyp/nvhe/hyp-smp.c
index 2997aa156d8e..4495aed04240 100644
--- a/arch/arm64/kvm/hyp/nvhe/hyp-smp.c
+++ b/arch/arm64/kvm/hyp/nvhe/hyp-smp.c
@@ -18,8 +18,7 @@ u64 __ro_after_init hyp_cpu_logical_map[NR_CPUS] = { [0 ... NR_CPUS-1] = INVALID
 
 u64 cpu_logical_map(unsigned int cpu)
 {
-	if (cpu >= ARRAY_SIZE(hyp_cpu_logical_map))
-		hyp_panic();
+	BUG_ON(cpu >= ARRAY_SIZE(hyp_cpu_logical_map));
 
 	return hyp_cpu_logical_map[cpu];
 }
@@ -30,8 +29,7 @@ unsigned long __hyp_per_cpu_offset(unsigned int cpu)
 	unsigned long this_cpu_base;
 	unsigned long elf_base;
 
-	if (cpu >= ARRAY_SIZE(kvm_arm_hyp_percpu_base))
-		hyp_panic();
+	BUG_ON(cpu >= ARRAY_SIZE(kvm_arm_hyp_percpu_base));
 
 	cpu_base_array = (unsigned long *)hyp_symbol_addr(kvm_arm_hyp_percpu_base);
 	this_cpu_base = kern_hyp_va(cpu_base_array[cpu]);
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH AUTOSEL 5.11 036/104] KVM: arm64: Use BUG and BUG_ON in nVHE hyp

[Marc Zyngier]

Sasha,

On Wed, 05 May 2021 17:33:05 +0100,
Sasha Levin <sashal@kernel.org> wrote:
> 
> From: Andrew Scull <ascull@google.com>
> 
> [ Upstream commit f79e616f27ab6cd74deb0995a8eead3d1c9d65af ]
> 
> hyp_panic() reports the address of the panic by using ELR_EL2, but this
> isn't a useful address when hyp_panic() is called directly. Replace such
> direct calls with BUG() and BUG_ON() which use BRK to trigger an
> exception that then goes to hyp_panic() with the correct address. Also
> remove the hyp_panic() declaration from the header file to avoid
> accidental misuse.
> 
> Signed-off-by: Andrew Scull <ascull@google.com>
> Acked-by: Will Deacon <will@kernel.org>
> Signed-off-by: Marc Zyngier <maz@kernel.org>
> Link: https://lore.kernel.org/r/20210318143311.839894-5-ascull@google.com
> Signed-off-by: Sasha Levin <sashal@kernel.org>

This has no chance of working without the patches that enable BUG()
support at EL2, and *really* isn't stable material.

Please drop this patch.

Thanks,

	M.

-- 
Without deviation from the norm, progress is not possible.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH AUTOSEL 5.11 036/104] KVM: arm64: Use BUG and BUG_ON in nVHE hyp

[Sasha Levin]

On Wed, May 05, 2021 at 05:48:51PM +0100, Marc Zyngier wrote:
>Sasha,
>
>On Wed, 05 May 2021 17:33:05 +0100,
>Sasha Levin <sashal@kernel.org> wrote:
>>
>> From: Andrew Scull <ascull@google.com>
>>
>> [ Upstream commit f79e616f27ab6cd74deb0995a8eead3d1c9d65af ]
>>
>> hyp_panic() reports the address of the panic by using ELR_EL2, but this
>> isn't a useful address when hyp_panic() is called directly. Replace such
>> direct calls with BUG() and BUG_ON() which use BRK to trigger an
>> exception that then goes to hyp_panic() with the correct address. Also
>> remove the hyp_panic() declaration from the header file to avoid
>> accidental misuse.
>>
>> Signed-off-by: Andrew Scull <ascull@google.com>
>> Acked-by: Will Deacon <will@kernel.org>
>> Signed-off-by: Marc Zyngier <maz@kernel.org>
>> Link: https://lore.kernel.org/r/20210318143311.839894-5-ascull@google.com
>> Signed-off-by: Sasha Levin <sashal@kernel.org>
>
>This has no chance of working without the patches that enable BUG()
>support at EL2, and *really* isn't stable material.
>
>Please drop this patch.

Will do, thanks!

-- 
Thanks,
Sasha

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.11 038/104] Bluetooth: btusb: Enable quirk boolean flag for Mediatek Chip.

[Sasha Levin]

From: "mark-yw.chen" <mark-yw.chen@mediatek.com>

[ Upstream commit 27e554a4fcd84e499bf0a82122b8c4c3f1de38b6 ]

Adding support LE scatternet and WBS for Mediatek Chip

Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/bluetooth/btusb.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index a4f834a50a98..3620981e8b1c 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -397,7 +397,9 @@ static const struct usb_device_id blacklist_table[] = {
 
 	/* MediaTek Bluetooth devices */
 	{ USB_VENDOR_AND_INTERFACE_INFO(0x0e8d, 0xe0, 0x01, 0x01),
-	  .driver_info = BTUSB_MEDIATEK },
+	  .driver_info = BTUSB_MEDIATEK |
+			 BTUSB_WIDEBAND_SPEECH |
+			 BTUSB_VALID_LE_STATES },
 
 	/* Additional MediaTek MT7615E Bluetooth devices */
 	{ USB_DEVICE(0x13d3, 0x3560), .driver_info = BTUSB_MEDIATEK},
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.11 044/104] coresight: Do not scan for graph if none is present

[Sasha Levin]

From: Suzuki K Poulose <suzuki.poulose@arm.com>

[ Upstream commit 2b921b671a8d29c2adb255a86409aad1e3267309 ]

If a graph node is not found for a given node, of_get_next_endpoint()
will emit the following error message :

 OF: graph: no port node found in /<node_name>

If the given component doesn't have any explicit connections (e.g,
ETE) we could simply ignore the graph parsing. As for any legacy
component where this is mandatory, the device will not be usable
as before this patch. Updating the DT bindings to Yaml and enabling
the schema checks can detect such issues with the DT.

Cc: Mike Leach <mike.leach@linaro.org>
Cc: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20210405164307.1720226-11-suzuki.poulose@arm.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/hwtracing/coresight/coresight-platform.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/hwtracing/coresight/coresight-platform.c b/drivers/hwtracing/coresight/coresight-platform.c
index 3629b7885aca..c594f45319fc 100644
--- a/drivers/hwtracing/coresight/coresight-platform.c
+++ b/drivers/hwtracing/coresight/coresight-platform.c
@@ -90,6 +90,12 @@ static void of_coresight_get_ports_legacy(const struct device_node *node,
 	struct of_endpoint endpoint;
 	int in = 0, out = 0;
 
+	/*
+	 * Avoid warnings in of_graph_get_next_endpoint()
+	 * if the device doesn't have any graph connections
+	 */
+	if (!of_graph_is_present(node))
+		return;
 	do {
 		ep = of_graph_get_next_endpoint(node, ep);
 		if (!ep)
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.11 049/104] pinctrl: samsung: use 'int' for register masks in Exynos

[Sasha Levin]

From: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>

[ Upstream commit fa0c10a5f3a49130dd11281aa27e7e1c8654abc7 ]

The Special Function Registers on all Exynos SoC, including ARM64, are
32-bit wide, so entire driver uses matching functions like readl() or
writel().  On 64-bit ARM using unsigned long for register masks:
1. makes little sense as immediately after bitwise operation it will be
   cast to 32-bit value when calling writel(),
2. is actually error-prone because it might promote other operands to
   64-bit.

Addresses-Coverity: Unintentional integer overflow
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20210408195029.69974-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pinctrl/samsung/pinctrl-exynos.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index b9ea09fabf84..493079a47d05 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -55,7 +55,7 @@ static void exynos_irq_mask(struct irq_data *irqd)
 	struct exynos_irq_chip *our_chip = to_exynos_irq_chip(chip);
 	struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
 	unsigned long reg_mask = our_chip->eint_mask + bank->eint_offset;
-	unsigned long mask;
+	unsigned int mask;
 	unsigned long flags;
 
 	spin_lock_irqsave(&bank->slock, flags);
@@ -83,7 +83,7 @@ static void exynos_irq_unmask(struct irq_data *irqd)
 	struct exynos_irq_chip *our_chip = to_exynos_irq_chip(chip);
 	struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
 	unsigned long reg_mask = our_chip->eint_mask + bank->eint_offset;
-	unsigned long mask;
+	unsigned int mask;
 	unsigned long flags;
 
 	/*
@@ -483,7 +483,7 @@ static void exynos_irq_eint0_15(struct irq_desc *desc)
 	chained_irq_exit(chip, desc);
 }
 
-static inline void exynos_irq_demux_eint(unsigned long pend,
+static inline void exynos_irq_demux_eint(unsigned int pend,
 						struct irq_domain *domain)
 {
 	unsigned int irq;
@@ -500,8 +500,8 @@ static void exynos_irq_demux_eint16_31(struct irq_desc *desc)
 {
 	struct irq_chip *chip = irq_desc_get_chip(desc);
 	struct exynos_muxed_weint_data *eintd = irq_desc_get_handler_data(desc);
-	unsigned long pend;
-	unsigned long mask;
+	unsigned int pend;
+	unsigned int mask;
 	int i;
 
 	chained_irq_enter(chip, desc);
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.11 051/104] mt76: mt7615: fix key set/delete issues

[Sasha Levin]

From: Felix Fietkau <nbd@nbd.name>

[ Upstream commit 730d6d0da8d8f5905faafe645a5b3c08ac3f5a8f ]

There were multiple issues in the current key set/remove code:
- deleting a key with the previous key index deletes the current key
- BIP key would only be uploaded correctly initially and corrupted on rekey

Rework the code to better keep track of multiple keys and check for the
key index before deleting the current key

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt76/mt76.h     |  1 +
 .../net/wireless/mediatek/mt76/mt7615/mac.c   | 97 ++++++++++---------
 .../net/wireless/mediatek/mt76/mt7615/main.c  | 18 ++--
 3 files changed, 65 insertions(+), 51 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt76.h b/drivers/net/wireless/mediatek/mt76/mt76.h
index 3e496a188bf0..deaeff3713f5 100644
--- a/drivers/net/wireless/mediatek/mt76/mt76.h
+++ b/drivers/net/wireless/mediatek/mt76/mt76.h
@@ -221,6 +221,7 @@ struct mt76_wcid {
 
 	u16 idx;
 	u8 hw_key_idx;
+	u8 hw_key_idx2;
 
 	u8 sta:1;
 	u8 ext_phy:1;
diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/mac.c b/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
index fb10a6497ed0..ea17bbeb10f7 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
@@ -1031,7 +1031,7 @@ EXPORT_SYMBOL_GPL(mt7615_mac_set_rates);
 static int
 mt7615_mac_wtbl_update_key(struct mt7615_dev *dev, struct mt76_wcid *wcid,
 			   struct ieee80211_key_conf *key,
-			   enum mt7615_cipher_type cipher,
+			   enum mt7615_cipher_type cipher, u16 cipher_mask,
 			   enum set_key_cmd cmd)
 {
 	u32 addr = mt7615_mac_wtbl_addr(dev, wcid->idx) + 30 * 4;
@@ -1048,22 +1048,22 @@ mt7615_mac_wtbl_update_key(struct mt7615_dev *dev, struct mt76_wcid *wcid,
 			memcpy(data + 16, key->key + 24, 8);
 			memcpy(data + 24, key->key + 16, 8);
 		} else {
-			if (cipher != MT_CIPHER_BIP_CMAC_128 && wcid->cipher)
-				memmove(data + 16, data, 16);
-			if (cipher != MT_CIPHER_BIP_CMAC_128 || !wcid->cipher)
+			if (cipher_mask == BIT(cipher))
 				memcpy(data, key->key, key->keylen);
-			else if (cipher == MT_CIPHER_BIP_CMAC_128)
+			else if (cipher != MT_CIPHER_BIP_CMAC_128)
+				memcpy(data, key->key, 16);
+			if (cipher == MT_CIPHER_BIP_CMAC_128)
 				memcpy(data + 16, key->key, 16);
 		}
 	} else {
-		if (wcid->cipher & ~BIT(cipher)) {
-			if (cipher != MT_CIPHER_BIP_CMAC_128)
-				memmove(data, data + 16, 16);
+		if (cipher == MT_CIPHER_BIP_CMAC_128)
 			memset(data + 16, 0, 16);
-		} else {
+		else if (cipher_mask)
+			memset(data, 0, 16);
+		if (!cipher_mask)
 			memset(data, 0, sizeof(data));
-		}
 	}
+
 	mt76_wr_copy(dev, addr, data, sizeof(data));
 
 	return 0;
@@ -1071,7 +1071,7 @@ mt7615_mac_wtbl_update_key(struct mt7615_dev *dev, struct mt76_wcid *wcid,
 
 static int
 mt7615_mac_wtbl_update_pk(struct mt7615_dev *dev, struct mt76_wcid *wcid,
-			  enum mt7615_cipher_type cipher,
+			  enum mt7615_cipher_type cipher, u16 cipher_mask,
 			  int keyidx, enum set_key_cmd cmd)
 {
 	u32 addr = mt7615_mac_wtbl_addr(dev, wcid->idx), w0, w1;
@@ -1081,20 +1081,23 @@ mt7615_mac_wtbl_update_pk(struct mt7615_dev *dev, struct mt76_wcid *wcid,
 
 	w0 = mt76_rr(dev, addr);
 	w1 = mt76_rr(dev, addr + 4);
-	if (cmd == SET_KEY) {
-		w0 |= MT_WTBL_W0_RX_KEY_VALID |
-		      FIELD_PREP(MT_WTBL_W0_RX_IK_VALID,
-				 cipher == MT_CIPHER_BIP_CMAC_128);
-		if (cipher != MT_CIPHER_BIP_CMAC_128 ||
-		    !wcid->cipher)
-			w0 |= FIELD_PREP(MT_WTBL_W0_KEY_IDX, keyidx);
-	}  else {
-		if (!(wcid->cipher & ~BIT(cipher)))
-			w0 &= ~(MT_WTBL_W0_RX_KEY_VALID |
-				MT_WTBL_W0_KEY_IDX);
-		if (cipher == MT_CIPHER_BIP_CMAC_128)
-			w0 &= ~MT_WTBL_W0_RX_IK_VALID;
+
+	if (cipher_mask)
+		w0 |= MT_WTBL_W0_RX_KEY_VALID;
+	else
+		w0 &= ~(MT_WTBL_W0_RX_KEY_VALID | MT_WTBL_W0_KEY_IDX);
+	if (cipher_mask & BIT(MT_CIPHER_BIP_CMAC_128))
+		w0 |= MT_WTBL_W0_RX_IK_VALID;
+	else
+		w0 &= ~MT_WTBL_W0_RX_IK_VALID;
+
+	if (cmd == SET_KEY &&
+	    (cipher != MT_CIPHER_BIP_CMAC_128 ||
+	     cipher_mask == BIT(cipher))) {
+		w0 &= ~MT_WTBL_W0_KEY_IDX;
+		w0 |= FIELD_PREP(MT_WTBL_W0_KEY_IDX, keyidx);
 	}
+
 	mt76_wr(dev, MT_WTBL_RICR0, w0);
 	mt76_wr(dev, MT_WTBL_RICR1, w1);
 
@@ -1107,24 +1110,25 @@ mt7615_mac_wtbl_update_pk(struct mt7615_dev *dev, struct mt76_wcid *wcid,
 
 static void
 mt7615_mac_wtbl_update_cipher(struct mt7615_dev *dev, struct mt76_wcid *wcid,
-			      enum mt7615_cipher_type cipher,
+			      enum mt7615_cipher_type cipher, u16 cipher_mask,
 			      enum set_key_cmd cmd)
 {
 	u32 addr = mt7615_mac_wtbl_addr(dev, wcid->idx);
 
-	if (cmd == SET_KEY) {
-		if (cipher != MT_CIPHER_BIP_CMAC_128 || !wcid->cipher)
-			mt76_rmw(dev, addr + 2 * 4, MT_WTBL_W2_KEY_TYPE,
-				 FIELD_PREP(MT_WTBL_W2_KEY_TYPE, cipher));
-	} else {
-		if (cipher != MT_CIPHER_BIP_CMAC_128 &&
-		    wcid->cipher & BIT(MT_CIPHER_BIP_CMAC_128))
-			mt76_rmw(dev, addr + 2 * 4, MT_WTBL_W2_KEY_TYPE,
-				 FIELD_PREP(MT_WTBL_W2_KEY_TYPE,
-					    MT_CIPHER_BIP_CMAC_128));
-		else if (!(wcid->cipher & ~BIT(cipher)))
-			mt76_clear(dev, addr + 2 * 4, MT_WTBL_W2_KEY_TYPE);
+	if (!cipher_mask) {
+		mt76_clear(dev, addr + 2 * 4, MT_WTBL_W2_KEY_TYPE);
+		return;
 	}
+
+	if (cmd != SET_KEY)
+		return;
+
+	if (cipher == MT_CIPHER_BIP_CMAC_128 &&
+	    cipher_mask & ~BIT(MT_CIPHER_BIP_CMAC_128))
+		return;
+
+	mt76_rmw(dev, addr + 2 * 4, MT_WTBL_W2_KEY_TYPE,
+		 FIELD_PREP(MT_WTBL_W2_KEY_TYPE, cipher));
 }
 
 int __mt7615_mac_wtbl_set_key(struct mt7615_dev *dev,
@@ -1133,25 +1137,30 @@ int __mt7615_mac_wtbl_set_key(struct mt7615_dev *dev,
 			      enum set_key_cmd cmd)
 {
 	enum mt7615_cipher_type cipher;
+	u16 cipher_mask = wcid->cipher;
 	int err;
 
 	cipher = mt7615_mac_get_cipher(key->cipher);
 	if (cipher == MT_CIPHER_NONE)
 		return -EOPNOTSUPP;
 
-	mt7615_mac_wtbl_update_cipher(dev, wcid, cipher, cmd);
-	err = mt7615_mac_wtbl_update_key(dev, wcid, key, cipher, cmd);
+	if (cmd == SET_KEY)
+		cipher_mask |= BIT(cipher);
+	else
+		cipher_mask &= ~BIT(cipher);
+
+	mt7615_mac_wtbl_update_cipher(dev, wcid, cipher, cipher_mask, cmd);
+	err = mt7615_mac_wtbl_update_key(dev, wcid, key, cipher, cipher_mask,
+					 cmd);
 	if (err < 0)
 		return err;
 
-	err = mt7615_mac_wtbl_update_pk(dev, wcid, cipher, key->keyidx, cmd);
+	err = mt7615_mac_wtbl_update_pk(dev, wcid, cipher, cipher_mask,
+					key->keyidx, cmd);
 	if (err < 0)
 		return err;
 
-	if (cmd == SET_KEY)
-		wcid->cipher |= BIT(cipher);
-	else
-		wcid->cipher &= ~BIT(cipher);
+	wcid->cipher = cipher_mask;
 
 	return 0;
 }
diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/main.c b/drivers/net/wireless/mediatek/mt76/mt7615/main.c
index 56dd0b4e4460..7c631520e8f4 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/main.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/main.c
@@ -350,7 +350,8 @@ static int mt7615_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
 	struct mt7615_sta *msta = sta ? (struct mt7615_sta *)sta->drv_priv :
 				  &mvif->sta;
 	struct mt76_wcid *wcid = &msta->wcid;
-	int idx = key->keyidx, err;
+	int idx = key->keyidx, err = 0;
+	u8 *wcid_keyidx = &wcid->hw_key_idx;
 
 	/* The hardware does not support per-STA RX GTK, fallback
 	 * to software mode for these.
@@ -365,6 +366,7 @@ static int mt7615_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
 	/* fall back to sw encryption for unsupported ciphers */
 	switch (key->cipher) {
 	case WLAN_CIPHER_SUITE_AES_CMAC:
+		wcid_keyidx = &wcid->hw_key_idx2;
 		key->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIE;
 		break;
 	case WLAN_CIPHER_SUITE_TKIP:
@@ -382,12 +384,13 @@ static int mt7615_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
 
 	mt7615_mutex_acquire(dev);
 
-	if (cmd == SET_KEY) {
-		key->hw_key_idx = wcid->idx;
-		wcid->hw_key_idx = idx;
-	} else if (idx == wcid->hw_key_idx) {
-		wcid->hw_key_idx = -1;
-	}
+	if (cmd == SET_KEY)
+		*wcid_keyidx = idx;
+	else if (idx == *wcid_keyidx)
+		*wcid_keyidx = -1;
+	else
+		goto out;
+
 	mt76_wcid_key_setup(&dev->mt76, wcid,
 			    cmd == SET_KEY ? key : NULL);
 
@@ -396,6 +399,7 @@ static int mt7615_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
 	else
 		err = __mt7615_mac_wtbl_set_key(dev, wcid, key, cmd);
 
+out:
 	mt7615_mutex_release(dev);
 
 	return err;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.11 052/104] mt76: mt7615: support loading EEPROM for MT7613BE

[Sasha Levin]

From: Sander Vanheule <sander@svanheule.net>

[ Upstream commit 858ebf446bee7d5077bd99488aae617908c3f4fe ]

EEPROM blobs for MT7613BE radios start with (little endian) 0x7663,
which is also the PCI device ID for this device. The EEPROM is required
for the radio to work at useful power levels, otherwise only the lowest
power level is available.

Suggested-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt76/mt7615/eeprom.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/eeprom.c b/drivers/net/wireless/mediatek/mt76/mt7615/eeprom.c
index 3232ebd5eda6..a31fa2017f52 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/eeprom.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/eeprom.c
@@ -86,6 +86,7 @@ static int mt7615_check_eeprom(struct mt76_dev *dev)
 	switch (val) {
 	case 0x7615:
 	case 0x7622:
+	case 0x7663:
 		return 0;
 	default:
 		return -EINVAL;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.11 053/104] mt76: mt76x0: disable GTK offloading

[Sasha Levin]

From: David Bauer <mail@david-bauer.net>

[ Upstream commit 4b36cc6b390f18dbc59a45fb4141f90d7dfe2b23 ]

When operating two VAP on a MT7610 with encryption (PSK2, SAE, OWE),
only the first one to be created will transmit properly encrypteded
frames.

All subsequently created VAPs will sent out frames with the payload left
unencrypted, breaking multicast traffic (ICMP6 NDP) and potentially
disclosing information to a third party.

Disable GTK offloading and encrypt these frames in software to
circumvent this issue. THis only seems to be necessary on MT7610 chips,
as MT7612 is not affected from our testing.

Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt76/mt76x02_util.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/net/wireless/mediatek/mt76/mt76x02_util.c b/drivers/net/wireless/mediatek/mt76/mt76x02_util.c
index 7ac20d3c16d7..aaa597b941cd 100644
--- a/drivers/net/wireless/mediatek/mt76/mt76x02_util.c
+++ b/drivers/net/wireless/mediatek/mt76/mt76x02_util.c
@@ -447,6 +447,10 @@ int mt76x02_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
 	    !(key->flags & IEEE80211_KEY_FLAG_PAIRWISE))
 		return -EOPNOTSUPP;
 
+	/* MT76x0 GTK offloading does not work with more than one VIF */
+	if (is_mt76x0(dev) && !(key->flags & IEEE80211_KEY_FLAG_PAIRWISE))
+		return -EOPNOTSUPP;
+
 	msta = sta ? (struct mt76x02_sta *)sta->drv_priv : NULL;
 	wcid = msta ? &msta->wcid : &mvif->group_wcid;
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.11 054/104] mt76: mt7915: always check return value from mt7915_mcu_alloc_wtbl_req

[Sasha Levin]

From: Lorenzo Bianconi <lorenzo@kernel.org>

[ Upstream commit 45f93e368211fbbd247e1ece254ffb121e20fa10 ]

As done for mt76_connac_mcu_alloc_wtbl_req, even if this is not a real
bug since mt7915_mcu_alloc_wtbl_req routine can fails just if nskb is NULL,
always check return value from mt7915_mcu_alloc_wtbl_req in order to avoid
possible future mistake.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt76/mt7915/mcu.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c b/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c
index e211a2bd4d3c..1cbae0eacfe9 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c
@@ -1170,6 +1170,9 @@ mt7915_mcu_sta_ba(struct mt7915_dev *dev,
 
 	wtbl_hdr = mt7915_mcu_alloc_wtbl_req(dev, msta, WTBL_SET, sta_wtbl,
 					     &skb);
+	if (IS_ERR(wtbl_hdr))
+		return PTR_ERR(wtbl_hdr);
+
 	mt7915_mcu_wtbl_ba_tlv(skb, params, enable, tx, sta_wtbl, wtbl_hdr);
 
 	ret = mt76_mcu_skb_send_msg(&dev->mt76, skb,
@@ -1686,6 +1689,9 @@ int mt7915_mcu_sta_update_hdr_trans(struct mt7915_dev *dev,
 		return -ENOMEM;
 
 	wtbl_hdr = mt7915_mcu_alloc_wtbl_req(dev, msta, WTBL_SET, NULL, &skb);
+	if (IS_ERR(wtbl_hdr))
+		return PTR_ERR(wtbl_hdr);
+
 	mt7915_mcu_wtbl_hdr_trans_tlv(skb, vif, sta, NULL, wtbl_hdr);
 
 	return mt76_mcu_skb_send_msg(&dev->mt76, skb, MCU_EXT_CMD_WTBL_UPDATE,
@@ -1710,6 +1716,9 @@ int mt7915_mcu_add_smps(struct mt7915_dev *dev, struct ieee80211_vif *vif,
 
 	wtbl_hdr = mt7915_mcu_alloc_wtbl_req(dev, msta, WTBL_SET, sta_wtbl,
 					     &skb);
+	if (IS_ERR(wtbl_hdr))
+		return PTR_ERR(wtbl_hdr);
+
 	mt7915_mcu_wtbl_smps_tlv(skb, sta, sta_wtbl, wtbl_hdr);
 
 	return mt76_mcu_skb_send_msg(&dev->mt76, skb,
@@ -2279,6 +2288,9 @@ int mt7915_mcu_add_sta(struct mt7915_dev *dev, struct ieee80211_vif *vif,
 
 	wtbl_hdr = mt7915_mcu_alloc_wtbl_req(dev, msta, WTBL_RESET_AND_SET,
 					     sta_wtbl, &skb);
+	if (IS_ERR(wtbl_hdr))
+		return PTR_ERR(wtbl_hdr);
+
 	if (enable) {
 		mt7915_mcu_wtbl_generic_tlv(skb, vif, sta, sta_wtbl, wtbl_hdr);
 		mt7915_mcu_wtbl_hdr_trans_tlv(skb, vif, sta, sta_wtbl, wtbl_hdr);
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.11 055/104] mt76: mt7915: fix key set/delete issue

[Sasha Levin]

From: Felix Fietkau <nbd@nbd.name>

[ Upstream commit 1da4fd48d28436f8b690cdc2879603dede6d8355 ]

Deleting a key with the previous key index deletes the current key
Rework the code to better keep track of multiple keys and check for the
key index before deleting the current key

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../net/wireless/mediatek/mt76/mt7915/main.c  | 25 +++++++++++++------
 1 file changed, 18 insertions(+), 7 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/main.c b/drivers/net/wireless/mediatek/mt76/mt7915/main.c
index 0c82aa2ef219..2c75a5987544 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/main.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/main.c
@@ -314,7 +314,9 @@ static int mt7915_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
 	struct mt7915_sta *msta = sta ? (struct mt7915_sta *)sta->drv_priv :
 				  &mvif->sta;
 	struct mt76_wcid *wcid = &msta->wcid;
+	u8 *wcid_keyidx = &wcid->hw_key_idx;
 	int idx = key->keyidx;
+	int err = 0;
 
 	/* The hardware does not support per-STA RX GTK, fallback
 	 * to software mode for these.
@@ -329,6 +331,7 @@ static int mt7915_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
 	/* fall back to sw encryption for unsupported ciphers */
 	switch (key->cipher) {
 	case WLAN_CIPHER_SUITE_AES_CMAC:
+		wcid_keyidx = &wcid->hw_key_idx2;
 		key->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIE;
 		break;
 	case WLAN_CIPHER_SUITE_TKIP:
@@ -344,16 +347,24 @@ static int mt7915_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
 		return -EOPNOTSUPP;
 	}
 
-	if (cmd == SET_KEY) {
-		key->hw_key_idx = wcid->idx;
-		wcid->hw_key_idx = idx;
-	} else if (idx == wcid->hw_key_idx) {
-		wcid->hw_key_idx = -1;
-	}
+	mutex_lock(&dev->mt76.mutex);
+
+	if (cmd == SET_KEY)
+		*wcid_keyidx = idx;
+	else if (idx == *wcid_keyidx)
+		*wcid_keyidx = -1;
+	else
+		goto out;
+
 	mt76_wcid_key_setup(&dev->mt76, wcid,
 			    cmd == SET_KEY ? key : NULL);
 
-	return mt7915_mcu_add_key(dev, vif, msta, key, cmd);
+	err = mt7915_mcu_add_key(dev, vif, msta, key, cmd);
+
+out:
+	mutex_unlock(&dev->mt76.mutex);
+
+	return err;
 }
 
 static int mt7915_config(struct ieee80211_hw *hw, u32 changed)
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.11 056/104] mt76: mt7915: fix txpower init for TSSI off chips

[Sasha Levin]

From: Shayne Chen <shayne.chen@mediatek.com>

[ Upstream commit a226ccd04c479ccd23d6927c64bad1b441707f70 ]

Fix incorrect txpower init value for TSSI off chips which causes
too small txpower.

Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../wireless/mediatek/mt76/mt7915/eeprom.c    | 19 +++++++++++++------
 1 file changed, 13 insertions(+), 6 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/eeprom.c b/drivers/net/wireless/mediatek/mt76/mt7915/eeprom.c
index 7a2be3f61398..c3e32555cf24 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/eeprom.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/eeprom.c
@@ -114,7 +114,7 @@ int mt7915_eeprom_get_target_power(struct mt7915_dev *dev,
 				   struct ieee80211_channel *chan,
 				   u8 chain_idx)
 {
-	int index;
+	int index, target_power;
 	bool tssi_on;
 
 	if (chain_idx > 3)
@@ -123,15 +123,22 @@ int mt7915_eeprom_get_target_power(struct mt7915_dev *dev,
 	tssi_on = mt7915_tssi_enabled(dev, chan->band);
 
 	if (chan->band == NL80211_BAND_2GHZ) {
-		index = MT_EE_TX0_POWER_2G + chain_idx * 3 + !tssi_on;
+		index = MT_EE_TX0_POWER_2G + chain_idx * 3;
+		target_power = mt7915_eeprom_read(dev, index);
+
+		if (!tssi_on)
+			target_power += mt7915_eeprom_read(dev, index + 1);
 	} else {
-		int group = tssi_on ?
-			    mt7915_get_channel_group(chan->hw_value) : 8;
+		int group = mt7915_get_channel_group(chan->hw_value);
+
+		index = MT_EE_TX0_POWER_5G + chain_idx * 12;
+		target_power = mt7915_eeprom_read(dev, index + group);
 
-		index = MT_EE_TX0_POWER_5G + chain_idx * 12 + group;
+		if (!tssi_on)
+			target_power += mt7915_eeprom_read(dev, index + 8);
 	}
 
-	return mt7915_eeprom_read(dev, index);
+	return target_power;
 }
 
 static const u8 sku_cck_delta_map[] = {
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.11 057/104] mt76: mt7915: add wifi subsystem reset

[Sasha Levin]

From: Ryder Lee <ryder.lee@mediatek.com>

[ Upstream commit e07419a7dca97dd9bddfe5d099380857c19535f3 ]

Reset wifi subsystem when MCU is already running.
Fixes firmware download failure after soft reboot on systems where the PCIe
reset could not be performed properly.

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Co-developed-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../net/wireless/mediatek/mt76/mt7915/init.c  | 58 ++++++++++++++++++-
 .../net/wireless/mediatek/mt76/mt7915/mcu.c   | 15 +----
 .../net/wireless/mediatek/mt76/mt7915/regs.h  | 13 +++++
 3 files changed, 70 insertions(+), 16 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/init.c b/drivers/net/wireless/mediatek/mt76/mt7915/init.c
index 2ec18aaa8280..aaa8006e0950 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/init.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/init.c
@@ -4,6 +4,7 @@
 #include <linux/etherdevice.h>
 #include "mt7915.h"
 #include "mac.h"
+#include "mcu.h"
 #include "eeprom.h"
 
 #define CCK_RATE(_idx, _rate) {						\
@@ -282,9 +283,50 @@ static void mt7915_init_work(struct work_struct *work)
 	mt7915_register_ext_phy(dev);
 }
 
+static void mt7915_wfsys_reset(struct mt7915_dev *dev)
+{
+	u32 val = MT_TOP_PWR_KEY | MT_TOP_PWR_SW_PWR_ON | MT_TOP_PWR_PWR_ON;
+	u32 reg = mt7915_reg_map_l1(dev, MT_TOP_MISC);
+
+#define MT_MCU_DUMMY_RANDOM	GENMASK(15, 0)
+#define MT_MCU_DUMMY_DEFAULT	GENMASK(31, 16)
+
+	mt76_wr(dev, MT_MCU_WFDMA0_DUMMY_CR, MT_MCU_DUMMY_RANDOM);
+
+	/* change to software control */
+	val |= MT_TOP_PWR_SW_RST;
+	mt76_wr(dev, MT_TOP_PWR_CTRL, val);
+
+	/* reset wfsys */
+	val &= ~MT_TOP_PWR_SW_RST;
+	mt76_wr(dev, MT_TOP_PWR_CTRL, val);
+
+	/* release wfsys then mcu re-excutes romcode */
+	val |= MT_TOP_PWR_SW_RST;
+	mt76_wr(dev, MT_TOP_PWR_CTRL, val);
+
+	/* switch to hw control */
+	val &= ~MT_TOP_PWR_SW_RST;
+	val |= MT_TOP_PWR_HW_CTRL;
+	mt76_wr(dev, MT_TOP_PWR_CTRL, val);
+
+	/* check whether mcu resets to default */
+	if (!mt76_poll_msec(dev, MT_MCU_WFDMA0_DUMMY_CR, MT_MCU_DUMMY_DEFAULT,
+			    MT_MCU_DUMMY_DEFAULT, 1000)) {
+		dev_err(dev->mt76.dev, "wifi subsystem reset failure\n");
+		return;
+	}
+
+	/* wfsys reset won't clear host registers */
+	mt76_clear(dev, reg, MT_TOP_MISC_FW_STATE);
+
+	msleep(100);
+}
+
 static int mt7915_init_hardware(struct mt7915_dev *dev)
 {
 	int ret, idx;
+	u32 val;
 
 	mt76_wr(dev, MT_INT_SOURCE_CSR, ~0);
 
@@ -294,6 +336,12 @@ static int mt7915_init_hardware(struct mt7915_dev *dev)
 
 	dev->dbdc_support = !!(mt7915_l1_rr(dev, MT_HW_BOUND) & BIT(5));
 
+	val = mt76_rr(dev, mt7915_reg_map_l1(dev, MT_TOP_MISC));
+
+	/* If MCU was already running, it is likely in a bad state */
+	if (FIELD_GET(MT_TOP_MISC_FW_STATE, val) > FW_STATE_FW_DOWNLOAD)
+		mt7915_wfsys_reset(dev);
+
 	ret = mt7915_dma_init(dev);
 	if (ret)
 		return ret;
@@ -307,8 +355,14 @@ static int mt7915_init_hardware(struct mt7915_dev *dev)
 	mt76_wr(dev, MT_SWDEF_MODE, MT_SWDEF_NORMAL_MODE);
 
 	ret = mt7915_mcu_init(dev);
-	if (ret)
-		return ret;
+	if (ret) {
+		/* Reset and try again */
+		mt7915_wfsys_reset(dev);
+
+		ret = mt7915_mcu_init(dev);
+		if (ret)
+			return ret;
+	}
 
 	ret = mt7915_eeprom_init(dev);
 	if (ret < 0)
diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c b/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c
index 1cbae0eacfe9..a0aa76ac16b9 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c
@@ -2780,21 +2780,8 @@ static int mt7915_load_ram(struct mt7915_dev *dev)
 
 static int mt7915_load_firmware(struct mt7915_dev *dev)
 {
+	u32 reg = mt7915_reg_map_l1(dev, MT_TOP_MISC);
 	int ret;
-	u32 val, reg = mt7915_reg_map_l1(dev, MT_TOP_MISC);
-
-	val = FIELD_PREP(MT_TOP_MISC_FW_STATE, FW_STATE_FW_DOWNLOAD);
-
-	if (!mt76_poll_msec(dev, reg, MT_TOP_MISC_FW_STATE, val, 1000)) {
-		/* restart firmware once */
-		__mt76_mcu_restart(&dev->mt76);
-		if (!mt76_poll_msec(dev, reg, MT_TOP_MISC_FW_STATE,
-				    val, 1000)) {
-			dev_err(dev->mt76.dev,
-				"Firmware is not ready for download\n");
-			return -EIO;
-		}
-	}
 
 	ret = mt7915_load_patch(dev);
 	if (ret)
diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/regs.h b/drivers/net/wireless/mediatek/mt76/mt7915/regs.h
index 848703e6eb7c..8a0ceb30392c 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/regs.h
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/regs.h
@@ -4,6 +4,11 @@
 #ifndef __MT7915_REGS_H
 #define __MT7915_REGS_H
 
+/* MCU WFDMA0 */
+#define MT_MCU_WFDMA0_BASE		0x2000
+#define MT_MCU_WFDMA0(ofs)		(MT_MCU_WFDMA0_BASE + (ofs))
+#define MT_MCU_WFDMA0_DUMMY_CR		MT_MCU_WFDMA0(0x120)
+
 /* MCU WFDMA1 */
 #define MT_MCU_WFDMA1_BASE		0x3000
 #define MT_MCU_WFDMA1(ofs)		(MT_MCU_WFDMA1_BASE + (ofs))
@@ -375,6 +380,14 @@
 #define MT_WFDMA1_PCIE1_BUSY_ENA_TX_FIFO1	BIT(1)
 #define MT_WFDMA1_PCIE1_BUSY_ENA_RX_FIFO	BIT(2)
 
+#define MT_TOP_RGU_BASE				0xf0000
+#define MT_TOP_PWR_CTRL				(MT_TOP_RGU_BASE + (0x0))
+#define MT_TOP_PWR_KEY				(0x5746 << 16)
+#define MT_TOP_PWR_SW_RST			BIT(0)
+#define MT_TOP_PWR_SW_PWR_ON			GENMASK(3, 2)
+#define MT_TOP_PWR_HW_CTRL			BIT(4)
+#define MT_TOP_PWR_PWR_ON			BIT(7)
+
 #define MT_INFRA_CFG_BASE		0xf1000
 #define MT_INFRA(ofs)			(MT_INFRA_CFG_BASE + (ofs))
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.11 058/104] i2c: imx: Fix PM reference leak in i2c_imx_reg_slave()

[Sasha Levin]

From: Ye Weihua <yeweihua4@huawei.com>

[ Upstream commit c4b1fcc310e655fa8414696c38a84d36c00684c8 ]

pm_runtime_get_sync() will increment the PM reference count even on
failure. Forgetting to put the reference again will result in a leak.

Replace it with pm_runtime_resume_and_get() to keep the usage counter
balanced.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Weihua <yeweihua4@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/i2c/busses/i2c-imx.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c
index a8e8af57e33f..56c5a9f8c138 100644
--- a/drivers/i2c/busses/i2c-imx.c
+++ b/drivers/i2c/busses/i2c-imx.c
@@ -763,7 +763,7 @@ static int i2c_imx_reg_slave(struct i2c_client *client)
 	i2c_imx->slave = client;
 
 	/* Resume */
-	ret = pm_runtime_get_sync(i2c_imx->adapter.dev.parent);
+	ret = pm_runtime_resume_and_get(i2c_imx->adapter.dev.parent);
 	if (ret < 0) {
 		dev_err(&i2c_imx->adapter.dev, "failed to resume i2c controller");
 		return ret;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.11 088/104] mt76: mt7615: fix entering driver-own state on mt7663

[Sasha Levin]

From: Felix Fietkau <nbd@nbd.name>

[ Upstream commit 5c7d374444afdeb9dd534a37c4f6c13af032da0c ]

Fixes hardware wakeup issues

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt76/mt7615/mcu.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c b/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c
index c13547841a4e..4c7083d17418 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c
@@ -291,12 +291,20 @@ static int mt7615_mcu_drv_pmctrl(struct mt7615_dev *dev)
 	u32 addr;
 	int err;
 
-	addr = is_mt7663(mdev) ? MT_PCIE_DOORBELL_PUSH : MT_CFG_LPCR_HOST;
+	if (is_mt7663(mdev)) {
+		/* Clear firmware own via N9 eint */
+		mt76_wr(dev, MT_PCIE_DOORBELL_PUSH, MT_CFG_LPCR_HOST_DRV_OWN);
+		mt76_poll(dev, MT_CONN_ON_MISC, MT_CFG_LPCR_HOST_FW_OWN, 0, 3000);
+
+		addr = MT_CONN_HIF_ON_LPCTL;
+	} else {
+		addr = MT_CFG_LPCR_HOST;
+	}
+
 	mt76_wr(dev, addr, MT_CFG_LPCR_HOST_DRV_OWN);
 
 	mt7622_trigger_hif_int(dev, true);
 
-	addr = is_mt7663(mdev) ? MT_CONN_HIF_ON_LPCTL : MT_CFG_LPCR_HOST;
 	err = !mt76_poll_msec(dev, addr, MT_CFG_LPCR_HOST_FW_OWN, 0, 3000);
 
 	mt7622_trigger_hif_int(dev, false);
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.11 095/104] net: ethernet: mtk_eth_soc: fix RX VLAN offload

[Sasha Levin]

From: Felix Fietkau <nbd@nbd.name>

[ Upstream commit 3f57d8c40fea9b20543cab4da12f4680d2ef182c ]

The VLAN ID in the rx descriptor is only valid if the RX_DMA_VTAG bit is
set. Fixes frames wrongly marked with VLAN tags.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
[Ilya: fix commit message]
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 2 +-
 drivers/net/ethernet/mediatek/mtk_eth_soc.h | 1 +
 2 files changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index 6d2d60675ffd..d930fcda9c3b 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -1319,7 +1319,7 @@ static int mtk_poll_rx(struct napi_struct *napi, int budget,
 		skb->protocol = eth_type_trans(skb, netdev);
 
 		if (netdev->features & NETIF_F_HW_VLAN_CTAG_RX &&
-		    RX_DMA_VID(trxd.rxd3))
+		    (trxd.rxd2 & RX_DMA_VTAG))
 			__vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q),
 					       RX_DMA_VID(trxd.rxd3));
 		skb_record_rx_queue(skb, 0);
diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.h b/drivers/net/ethernet/mediatek/mtk_eth_soc.h
index 454cfcd465fd..73ce1f0f307a 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.h
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.h
@@ -295,6 +295,7 @@
 #define RX_DMA_LSO		BIT(30)
 #define RX_DMA_PLEN0(_x)	(((_x) & 0x3fff) << 16)
 #define RX_DMA_GET_PLEN0(_x)	(((_x) >> 16) & 0x3fff)
+#define RX_DMA_VTAG		BIT(15)
 
 /* QDMA descriptor rxd3 */
 #define RX_DMA_VID(_x)		((_x) & 0xfff)
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel