[PATCH v15 0/3] Move HiSilicon 6421v600 SPMI and USB drivers out of staging

[PATCH v15 0/3] Move HiSilicon 6421v600 SPMI and USB drivers out of staging

[Mauro Carvalho Chehab]

Hi Greg,

Those are the remaining patches needed for USB3 to start working on HiKey 970.

I would prefer to have those merged during this cycle, as the PCIe patchset
currently under review depends on patch 1 and 2 of this series.

So, I dropped the cleanup patch from this series, due to a merge conflict with
the regulator's tree. I'll re-submit it against the mfd tree after the merge window. 

Mauro Carvalho Chehab (3):
  mfd: hi6421-spmi-pmic: move driver from staging
  dts: hisilicon: add support for the PMIC found on Hikey 970
  dts: hisilicon: add support for USB3 on Hikey 970

 .../mfd/hisilicon,hi6421-spmi-pmic.yaml       | 136 ++++++++++++++++++
 MAINTAINERS                                   |   7 +
 .../boot/dts/hisilicon/hi3670-hikey970.dts    | 129 ++++++++++++++---
 arch/arm64/boot/dts/hisilicon/hi3670.dtsi     |  56 ++++++++
 .../boot/dts/hisilicon/hikey970-pmic.dtsi     |  86 +++++++++++
 drivers/mfd/Kconfig                           |  16 +++
 drivers/mfd/Makefile                          |   1 +
 drivers/mfd/hi6421-spmi-pmic.c                |  72 ++++++++++
 drivers/staging/Kconfig                       |   2 -
 drivers/staging/Makefile                      |   1 -
 drivers/staging/hikey9xx/Kconfig              |  19 ---
 drivers/staging/hikey9xx/Makefile             |   3 -
 drivers/staging/hikey9xx/TODO                 |   5 -
 drivers/staging/hikey9xx/hi6421-spmi-pmic.c   |  72 ----------
 .../hikey9xx/hisilicon,hi6421-spmi-pmic.yaml  | 136 ------------------
 15 files changed, 484 insertions(+), 257 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml
 create mode 100644 arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi
 create mode 100644 drivers/mfd/hi6421-spmi-pmic.c
 delete mode 100644 drivers/staging/hikey9xx/Kconfig
 delete mode 100644 drivers/staging/hikey9xx/Makefile
 delete mode 100644 drivers/staging/hikey9xx/TODO
 delete mode 100644 drivers/staging/hikey9xx/hi6421-spmi-pmic.c
 delete mode 100644 drivers/staging/hikey9xx/hisilicon,hi6421-spmi-pmic.yaml

-- 
2.31.1



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v15 2/3] dts: hisilicon: add support for the PMIC found on Hikey 970

[Mauro Carvalho Chehab]

Add a device tree for the HiSilicon 6421v600 SPMI PMIC, used
on HiKey970 board.

As we now have support for it, change the fixed regulators
used by the SD I/O to use the proper LDO supplies.

Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
 .../boot/dts/hisilicon/hi3670-hikey970.dts    | 22 +----
 .../boot/dts/hisilicon/hikey970-pmic.dtsi     | 86 +++++++++++++++++++
 2 files changed, 89 insertions(+), 19 deletions(-)
 create mode 100644 arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi

diff --git a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
index d8abf442ee7e..7c32f5fd5cc5 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
@@ -12,6 +12,7 @@
 
 #include "hi3670.dtsi"
 #include "hikey970-pinctrl.dtsi"
+#include "hikey970-pmic.dtsi"
 
 / {
 	model = "HiKey970";
@@ -39,23 +40,6 @@ memory@0 {
 		reg = <0x0 0x0 0x0 0x0>;
 	};
 
-	sd_1v8: regulator-1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-always-on;
-	};
-
-	sd_3v3: regulator-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
 	wlan_en: wlan-en-1-8v {
 		compatible = "regulator-fixed";
 		regulator-name = "wlan-en-regulator";
@@ -402,8 +386,8 @@ &dwmmc1 {
 	pinctrl-0 = <&sd_pmx_func
 		     &sd_clk_cfg_func
 		     &sd_cfg_func>;
-	vmmc-supply = <&sd_3v3>;
-	vqmmc-supply = <&sd_1v8>;
+	vmmc-supply = <&ldo16>;
+	vqmmc-supply = <&ldo9>;
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi b/arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi
new file mode 100644
index 000000000000..03452e627641
--- /dev/null
+++ b/arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Hi6421v600 SPMI PMIC used at the HiKey970 Development Board
+ *
+ * Copyright (C) 2020, Huawei Tech. Co., Ltd.
+ */
+
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	spmi: spmi@fff24000 {
+		compatible = "hisilicon,kirin970-spmi-controller";
+		#address-cells = <2>;
+		#size-cells = <0>;
+		status = "okay";
+		reg = <0x0 0xfff24000 0x0 0x1000>;
+		hisilicon,spmi-channel = <2>;
+
+		pmic: pmic@0 {
+			compatible = "hisilicon,hi6421-spmi";
+			reg = <0 SPMI_USID>;
+
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			gpios = <&gpio28 0 0>;
+
+			regulators {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ldo3: LDO3 { /* HDMI */
+					regulator-name = "ldo3";
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <2000000>;
+					regulator-boot-on;
+				};
+
+				ldo4: LDO4 { /* 40 PIN */
+					regulator-name = "ldo4";
+					regulator-min-microvolt = <1725000>;
+					regulator-max-microvolt = <1900000>;
+					regulator-boot-on;
+				};
+
+				ldo9: LDO9 { /* SDCARD I/O */
+					regulator-name = "ldo9";
+					regulator-min-microvolt = <1750000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+				};
+
+				ldo15: LDO15 { /* UFS */
+					regulator-name = "ldo15";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-always-on;
+				};
+
+				ldo16: LDO16 { /* SD */
+					regulator-name = "ldo16";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-boot-on;
+				};
+
+				ldo17: LDO17 { /* USB HUB */
+					regulator-name = "ldo17";
+					regulator-min-microvolt = <2500000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				ldo33: LDO33 { /* PEX8606 */
+					regulator-name = "ldo33";
+					regulator-min-microvolt = <2500000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				ldo34: LDO34 { /* GPS AUX IN VDD */
+					regulator-name = "ldo34";
+					regulator-min-microvolt = <2600000>;
+					regulator-max-microvolt = <3300000>;
+				};
+			};
+		};
+	};
+};
-- 
2.31.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v15 3/3] dts: hisilicon: add support for USB3 on Hikey 970

[Mauro Carvalho Chehab]

Add the USB3 bindings for Kirin 970 phy and Hikey 970 board.

Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
 .../boot/dts/hisilicon/hi3670-hikey970.dts    | 107 ++++++++++++++++++
 arch/arm64/boot/dts/hisilicon/hi3670.dtsi     |  56 +++++++++
 2 files changed, 163 insertions(+)

diff --git a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
index 7c32f5fd5cc5..16f81f86e3fa 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
@@ -53,6 +53,30 @@ wlan_en: wlan-en-1-8v {
 		startup-delay-us = <70000>;
 		enable-active-high;
 	};
+
+	hikey_usbhub: hikey_usbhub {
+		compatible = "hisilicon,kirin970_hikey_usbhub";
+
+		typec-vbus-gpios = <&gpio26 1 0>;
+		otg-switch-gpios = <&gpio4 2 0>;
+		hub_reset_en_gpio = <&gpio0 3 0>;
+		hub-vdd-supply = <&ldo17>;
+		usb-role-switch;
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			hikey_usb_ep0: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&dwc3_role_switch>;
+			};
+			hikey_usb_ep1: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&rt1711h_ep>;
+			};
+		};
+	};
 };
 
 /*
@@ -430,3 +454,86 @@ &uart6 {
 	label = "LS-UART1";
 	status = "okay";
 };
+
+&usb_phy {
+	phy-supply = <&ldo17>;
+};
+
+&i2c1 {
+	status = "okay";
+
+	rt1711h: rt1711h@4e {
+		compatible = "richtek,rt1711h";
+		reg = <0x4e>;
+		status = "okay";
+		interrupt-parent = <&gpio27>;
+		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_cfg_func>;
+
+		usb_con: connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			data-role = "dual";
+			power-role = "dual";
+			try-power-role = "sink";
+			source-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)>;
+			sink-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)
+				PDO_VAR(5000, 5000, 1000)>;
+			op-sink-microwatt = <10000000>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@1 {
+					reg = <1>;
+					usb_con_ss: endpoint {
+						remote-endpoint = <&dwc3_ss>;
+					};
+				};
+			};
+		};
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			rt1711h_ep: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&hikey_usb_ep1>;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	/* USB HUB is on this bus at address 0x44 */
+	status = "okay";
+};
+
+&dwc3 { /* USB */
+	dr_mode = "otg";
+	maximum-speed = "super-speed";
+	phy_type = "utmi";
+	snps,dis-del-phy-power-chg-quirk;
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,tx_de_emphasis_quirk;
+	snps,tx_de_emphasis = <1>;
+	snps,dis-split-quirk;
+	snps,gctl-reset-quirk;
+	usb-role-switch;
+	role-switch-default-mode = "host";
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		dwc3_role_switch: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&hikey_usb_ep0>;
+		};
+
+		dwc3_ss: endpoint@1 {
+			reg = <1>;
+			remote-endpoint = <&usb_con_ss>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
index 20698cfd0637..1f228612192c 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
@@ -8,6 +8,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/hi3670-clock.h>
+#include <dt-bindings/usb/pd.h>
 
 / {
 	compatible = "hisilicon,hi3670";
@@ -785,5 +786,60 @@ i2c4: i2c@fdf0d000 {
 			pinctrl-0 = <&i2c4_pmx_func &i2c4_cfg_func>;
 			status = "disabled";
 		};
+
+		usb3_otg_bc: usb3_otg_bc@ff200000 {
+			compatible = "syscon", "simple-mfd";
+			reg = <0x0 0xff200000 0x0 0x1000>;
+
+			usb_phy: usbphy {
+				compatible = "hisilicon,hi3670-usb-phy";
+				#phy-cells = <0>;
+				hisilicon,pericrg-syscon = <&crg_ctrl>;
+				hisilicon,pctrl-syscon = <&pctrl>;
+				hisilicon,sctrl-syscon = <&sctrl>;
+				hisilicon,eye-diagram-param = <0xFDFEE4>;
+				hisilicon,tx-vboost-lvl = <0x5>;
+			};
+		};
+
+		usb31_misc_rst: usb31_misc_rst_controller {
+			compatible = "hisilicon,hi3660-reset";
+			#reset-cells = <2>;
+			hisi,rst-syscon = <&usb3_otg_bc>;
+		};
+
+		usb3: hisi_dwc3 {
+			compatible = "hisilicon,hi3670-dwc3";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&crg_ctrl HI3670_CLK_GATE_ABB_USB>,
+				  <&crg_ctrl HI3670_HCLK_GATE_USB3OTG>,
+				  <&crg_ctrl HI3670_CLK_GATE_USB3OTG_REF>,
+				  <&crg_ctrl HI3670_ACLK_GATE_USB3DVFS>;
+			clock-names = "clk_gate_abb_usb",
+				      "hclk_gate_usb3otg",
+				      "clk_gate_usb3otg_ref",
+				      "aclk_gate_usb3dvfs";
+
+			assigned-clocks = <&crg_ctrl HI3670_ACLK_GATE_USB3DVFS>;
+			assigned-clock-rates = <238000000>;
+			resets = <&crg_rst 0x90 6>,
+				 <&crg_rst 0x90 7>,
+				 <&usb31_misc_rst 0xA0 8>,
+				 <&usb31_misc_rst 0xA0 9>;
+
+			dwc3: usb@ff100000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0xff100000 0x0 0x100000>;
+
+				interrupts = <0 159 IRQ_TYPE_LEVEL_HIGH>,
+					    <0 161 IRQ_TYPE_LEVEL_HIGH>;
+
+				phys = <&usb_phy>;
+				phy-names = "usb3-phy";
+			};
+		};
 	};
 };
-- 
2.31.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v15 0/3] Move HiSilicon 6421v600 SPMI and USB drivers out of staging

[Greg Kroah-Hartman]

On Fri, Jul 23, 2021 at 09:40:05AM +0200, Mauro Carvalho Chehab wrote:
> Hi Greg,
> 
> Those are the remaining patches needed for USB3 to start working on HiKey 970.
> 
> I would prefer to have those merged during this cycle, as the PCIe patchset
> currently under review depends on patch 1 and 2 of this series.
> 
> So, I dropped the cleanup patch from this series, due to a merge conflict with
> the regulator's tree. I'll re-submit it against the mfd tree after the merge window. 
> 
> Mauro Carvalho Chehab (3):
>   mfd: hi6421-spmi-pmic: move driver from staging
>   dts: hisilicon: add support for the PMIC found on Hikey 970
>   dts: hisilicon: add support for USB3 on Hikey 970

I've applied patch 1 here.

The other two I need acks from the DT maintainers before I can do
anything with them.

thanks,

greg k-h

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v15 0/3] Move HiSilicon 6421v600 SPMI and USB drivers out of staging

[Rob Herring]

On Fri, Jul 23, 2021 at 10:14:44AM +0200, Greg Kroah-Hartman wrote:
> On Fri, Jul 23, 2021 at 09:40:05AM +0200, Mauro Carvalho Chehab wrote:
> > Hi Greg,
> > 
> > Those are the remaining patches needed for USB3 to start working on HiKey 970.
> > 
> > I would prefer to have those merged during this cycle, as the PCIe patchset
> > currently under review depends on patch 1 and 2 of this series.
> > 
> > So, I dropped the cleanup patch from this series, due to a merge conflict with
> > the regulator's tree. I'll re-submit it against the mfd tree after the merge window. 
> > 
> > Mauro Carvalho Chehab (3):
> >   mfd: hi6421-spmi-pmic: move driver from staging
> >   dts: hisilicon: add support for the PMIC found on Hikey 970
> >   dts: hisilicon: add support for USB3 on Hikey 970
> 
> I've applied patch 1 here.
> 
> The other two I need acks from the DT maintainers before I can do
> anything with them.

I only review the bindings (patch 1). I can only deal with 1 firehose. 
The dts files should go thru the HiSilicon maintainers.

Rob

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel