From: Md Danish Anwar <a0501179@ti.com>
To: Roger Quadros <rogerq@kernel.org>,
MD Danish Anwar <danishanwar@ti.com>,
"Andrew F. Davis" <afd@ti.com>, Suman Anna <s-anna@ti.com>,
Vignesh Raghavendra <vigneshr@ti.com>,
Mathieu Poirier <mathieu.poirier@linaro.org>,
Bjorn Andersson <andersson@kernel.org>,
Santosh Shilimkar <ssantosh@kernel.org>,
Nishanth Menon <nm@ti.com>
Cc: <linux-remoteproc@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <linux-omap@vger.kernel.org>,
<srk@ti.com>, <devicetree@vger.kernel.org>,
<netdev@vger.kernel.org>
Subject: Re: [EXTERNAL] Re: [PATCH v4 3/5] soc: ti: pruss: Add pruss_cfg_read()/update() API
Date: Thu, 16 Mar 2023 16:59:49 +0530 [thread overview]
Message-ID: <a3e26ef1-b7e7-f6da-94ff-4a8bf80649f6@ti.com> (raw)
In-Reply-To: <c52ae883-b0c9-8f92-98ae-fb9e9ad30420@ti.com>
Roger,
On 16/03/23 16:38, Md Danish Anwar wrote:
>
> On 15/03/23 17:37, Roger Quadros wrote:
>> Danish,
>>
>> On 13/03/2023 13:11, MD Danish Anwar wrote:
>>> From: Suman Anna <s-anna@ti.com>
>>>
>>> Add two new generic API pruss_cfg_read() and pruss_cfg_update() to
>>> the PRUSS platform driver to read and program respectively a register
>>> within the PRUSS CFG sub-module represented by a syscon driver.
>>>
>>> These APIs are internal to PRUSS driver. Various useful registers
>>> and macros for certain register bit-fields and their values have also
>>> been added.
>>>
>>> Signed-off-by: Suman Anna <s-anna@ti.com>
>>> Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
>>> Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
>>> Signed-off-by: Puranjay Mohan <p-mohan@ti.com>
>>> Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
>>> ---
>>> drivers/soc/ti/pruss.c | 39 ++++++++++++++
>>> include/linux/remoteproc/pruss.h | 87 ++++++++++++++++++++++++++++++++
>>> 2 files changed, 126 insertions(+)
>>>
>>> diff --git a/drivers/soc/ti/pruss.c b/drivers/soc/ti/pruss.c
>>> index c8053c0d735f..26d8129b515c 100644
>>> --- a/drivers/soc/ti/pruss.c
>>> +++ b/drivers/soc/ti/pruss.c
>>> @@ -164,6 +164,45 @@ int pruss_release_mem_region(struct pruss *pruss,
>>> }
>>> EXPORT_SYMBOL_GPL(pruss_release_mem_region);
>>>
>>> +/**
>>> + * pruss_cfg_read() - read a PRUSS CFG sub-module register
>>> + * @pruss: the pruss instance handle
>>> + * @reg: register offset within the CFG sub-module
>>> + * @val: pointer to return the value in
>>> + *
>>> + * Reads a given register within the PRUSS CFG sub-module and
>>> + * returns it through the passed-in @val pointer
>>> + *
>>> + * Return: 0 on success, or an error code otherwise
>>> + */
>>> +static int pruss_cfg_read(struct pruss *pruss, unsigned int reg, unsigned int *val)
>>> +{
>>> + if (IS_ERR_OR_NULL(pruss))
>>> + return -EINVAL;
>>> +
>>> + return regmap_read(pruss->cfg_regmap, reg, val);
>>> +}
>>> +
>>> +/**
>>> + * pruss_cfg_update() - configure a PRUSS CFG sub-module register
>>> + * @pruss: the pruss instance handle
>>> + * @reg: register offset within the CFG sub-module
>>> + * @mask: bit mask to use for programming the @val
>>> + * @val: value to write
>>> + *
>>> + * Programs a given register within the PRUSS CFG sub-module
>>> + *
>>> + * Return: 0 on success, or an error code otherwise
>>> + */
>>> +static int pruss_cfg_update(struct pruss *pruss, unsigned int reg,
>>> + unsigned int mask, unsigned int val)
>>> +{
>>> + if (IS_ERR_OR_NULL(pruss))
>>> + return -EINVAL;
>>> +
>>> + return regmap_update_bits(pruss->cfg_regmap, reg, mask, val);
>>> +}
>>> +
>>> static void pruss_of_free_clk_provider(void *data)
>>> {
>>> struct device_node *clk_mux_np = data;
>>> diff --git a/include/linux/remoteproc/pruss.h b/include/linux/remoteproc/pruss.h
>>> index 33f930e0a0ce..12ef10b9fe9a 100644
>>> --- a/include/linux/remoteproc/pruss.h
>>> +++ b/include/linux/remoteproc/pruss.h
>>> @@ -10,12 +10,99 @@
>>> #ifndef __LINUX_PRUSS_H
>>> #define __LINUX_PRUSS_H
>>>
>>> +#include <linux/bits.h>
>>> #include <linux/device.h>
>>> #include <linux/err.h>
>>> #include <linux/types.h>
>>>
>>> #define PRU_RPROC_DRVNAME "pru-rproc"
>>>
>>> +/*
>>> + * PRU_ICSS_CFG registers
>>> + * SYSCFG, ISRP, ISP, IESP, IECP, SCRP applicable on AMxxxx devices only
>>> + */
>>> +#define PRUSS_CFG_REVID 0x00
>>> +#define PRUSS_CFG_SYSCFG 0x04
>>> +#define PRUSS_CFG_GPCFG(x) (0x08 + (x) * 4)
>>> +#define PRUSS_CFG_CGR 0x10
>>> +#define PRUSS_CFG_ISRP 0x14
>>> +#define PRUSS_CFG_ISP 0x18
>>> +#define PRUSS_CFG_IESP 0x1C
>>> +#define PRUSS_CFG_IECP 0x20
>>> +#define PRUSS_CFG_SCRP 0x24
>>> +#define PRUSS_CFG_PMAO 0x28
>>> +#define PRUSS_CFG_MII_RT 0x2C
>>> +#define PRUSS_CFG_IEPCLK 0x30
>>> +#define PRUSS_CFG_SPP 0x34
>>> +#define PRUSS_CFG_PIN_MX 0x40
>>> +
>>> +/* PRUSS_GPCFG register bits */
>>> +#define PRUSS_GPCFG_PRU_GPO_SH_SEL BIT(25)
>>> +
>>> +#define PRUSS_GPCFG_PRU_DIV1_SHIFT 20
>>> +#define PRUSS_GPCFG_PRU_DIV1_MASK GENMASK(24, 20)
>>> +
>>> +#define PRUSS_GPCFG_PRU_DIV0_SHIFT 15
>>> +#define PRUSS_GPCFG_PRU_DIV0_MASK GENMASK(15, 19)
>>> +
>>> +#define PRUSS_GPCFG_PRU_GPO_MODE BIT(14)
>>> +#define PRUSS_GPCFG_PRU_GPO_MODE_DIRECT 0
>>> +#define PRUSS_GPCFG_PRU_GPO_MODE_SERIAL BIT(14)
>>> +
>>> +#define PRUSS_GPCFG_PRU_GPI_SB BIT(13)
>>> +
>>> +#define PRUSS_GPCFG_PRU_GPI_DIV1_SHIFT 8
>>> +#define PRUSS_GPCFG_PRU_GPI_DIV1_MASK GENMASK(12, 8)
>>> +
>>> +#define PRUSS_GPCFG_PRU_GPI_DIV0_SHIFT 3
>>> +#define PRUSS_GPCFG_PRU_GPI_DIV0_MASK GENMASK(7, 3)
>>> +
>>> +#define PRUSS_GPCFG_PRU_GPI_CLK_MODE_POSITIVE 0
>>> +#define PRUSS_GPCFG_PRU_GPI_CLK_MODE_NEGATIVE BIT(2)
>>> +#define PRUSS_GPCFG_PRU_GPI_CLK_MODE BIT(2)
>>> +
>>> +#define PRUSS_GPCFG_PRU_GPI_MODE_MASK GENMASK(1, 0)
>>> +#define PRUSS_GPCFG_PRU_GPI_MODE_SHIFT 0
>>> +
>>> +#define PRUSS_GPCFG_PRU_MUX_SEL_SHIFT 26
>>> +#define PRUSS_GPCFG_PRU_MUX_SEL_MASK GENMASK(29, 26)
>>> +
>>> +/* PRUSS_MII_RT register bits */
>>> +#define PRUSS_MII_RT_EVENT_EN BIT(0)
>>> +
>>> +/* PRUSS_SPP register bits */
>>> +#define PRUSS_SPP_XFER_SHIFT_EN BIT(1)
>>> +#define PRUSS_SPP_PRU1_PAD_HP_EN BIT(0)
>>
>> Can we please move all the above definitions to private driver/soc/ti/pruss.h?
>> You can also add pruss_cfg_read and pruss_cfg_update there.
>>
There is no driver/soc/ti/pruss.h. The pruss.h file is located in
include/linux/remoteproc/pruss.h and there is one pruss_driver.h file which is
located in include/linux/pruss_driver.h
Do you want me to create another header file at driver/soc/ti/pruss.h and place
all these definitions inside that?
Please let me know.
>
> Sure Roger, I'll move all these definitions to pruss.h
>
>>> +
>>> +/*
>>> + * enum pruss_gp_mux_sel - PRUSS GPI/O Mux modes for the
>>> + * PRUSS_GPCFG0/1 registers
>>> + *
>>> + * NOTE: The below defines are the most common values, but there
>>> + * are some exceptions like on 66AK2G, where the RESERVED and MII2
>>> + * values are interchanged. Also, this bit-field does not exist on
>>> + * AM335x SoCs
>>> + */
>>> +enum pruss_gp_mux_sel {
>>> + PRUSS_GP_MUX_SEL_GP = 0,
>>> + PRUSS_GP_MUX_SEL_ENDAT,
>>> + PRUSS_GP_MUX_SEL_RESERVED,
>>> + PRUSS_GP_MUX_SEL_SD,
>>> + PRUSS_GP_MUX_SEL_MII2,
>>> + PRUSS_GP_MUX_SEL_MAX,
>>> +};
>>> +
>>> +/*
>>> + * enum pruss_gpi_mode - PRUSS GPI configuration modes, used
>>> + * to program the PRUSS_GPCFG0/1 registers
>>> + */
>>> +enum pruss_gpi_mode {
>>> + PRUSS_GPI_MODE_DIRECT = 0,
>>> + PRUSS_GPI_MODE_PARALLEL,
>>> + PRUSS_GPI_MODE_28BIT_SHIFT,
>>> + PRUSS_GPI_MODE_MII,
>>> +};
>>> +
>>> /**
>>> * enum pruss_pru_id - PRU core identifiers
>>> * @PRUSS_PRU0: PRU Core 0.
>>
>> cheers,
>> -roger
>
--
Thanks and Regards,
Danish.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2023-03-16 11:31 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-03-13 11:11 [PATCH v4 0/5] Introduce PRU platform consumer API MD Danish Anwar
2023-03-13 11:11 ` [PATCH v4 1/5] soc: ti: pruss: Add pruss_get()/put() API MD Danish Anwar
2023-03-13 16:19 ` Andrew Davis
2023-03-13 11:11 ` [PATCH v4 2/5] soc: ti: pruss: Add pruss_{request,release}_mem_region() API MD Danish Anwar
2023-03-17 8:56 ` Roger Quadros
2023-03-20 5:11 ` [EXTERNAL] " Md Danish Anwar
2023-03-20 16:18 ` Andrew Davis
2023-03-21 5:23 ` Md Danish Anwar
2023-03-21 9:24 ` Roger Quadros
2023-03-21 9:48 ` [EXTERNAL] " Md Danish Anwar
2023-03-21 10:23 ` Roger Quadros
2023-03-21 10:45 ` Md Danish Anwar
2023-03-13 11:11 ` [PATCH v4 3/5] soc: ti: pruss: Add pruss_cfg_read()/update() API MD Danish Anwar
2023-03-15 12:07 ` Roger Quadros
2023-03-16 11:08 ` [EXTERNAL] " Md Danish Anwar
2023-03-16 11:29 ` Md Danish Anwar [this message]
2023-03-16 11:32 ` Roger Quadros
2023-03-16 11:34 ` [EXTERNAL] " Md Danish Anwar
2023-03-13 11:11 ` [PATCH v4 4/5] soc: ti: pruss: Add helper functions to set GPI mode, MII_RT_event and XFR MD Danish Anwar
2023-03-15 12:22 ` Roger Quadros
2023-03-16 11:05 ` [EXTERNAL] " Md Danish Anwar
2023-03-16 11:36 ` Roger Quadros
2023-03-16 11:44 ` Md Danish Anwar
2023-03-16 12:19 ` Roger Quadros
2023-03-16 13:11 ` [EXTERNAL] " Md Danish Anwar
2023-03-16 14:04 ` Roger Quadros
2023-03-17 5:02 ` [EXTERNAL] " Md Danish Anwar
2023-03-17 8:31 ` Roger Quadros
2023-03-17 8:55 ` [EXTERNAL] " Md Danish Anwar
2023-03-13 11:11 ` [PATCH v4 5/5] soc: ti: pruss: Add helper functions to get/set PRUSS_CFG_GPMUX MD Danish Anwar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=a3e26ef1-b7e7-f6da-94ff-4a8bf80649f6@ti.com \
--to=a0501179@ti.com \
--cc=afd@ti.com \
--cc=andersson@kernel.org \
--cc=danishanwar@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=linux-remoteproc@vger.kernel.org \
--cc=mathieu.poirier@linaro.org \
--cc=netdev@vger.kernel.org \
--cc=nm@ti.com \
--cc=rogerq@kernel.org \
--cc=s-anna@ti.com \
--cc=srk@ti.com \
--cc=ssantosh@kernel.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).