[PATCH net-next 0/3] net: stmmac: Improvements for -next

[PATCH net-next 0/3] net: stmmac: Improvements for -next

[Jose Abreu]

Misc improvements for stmmac.

Patch 1/3, adds the support for Split Header feature in GMAC4+ cores. This
was already available for XGMAC and now with this change it is supported in
all relevant cores.

Patch 2/3, adds the support for C45 MDIO callbacks in XGMAC cores.

Patch 3/3, removes the speed dependency in TC CBS callbacks because XGMAC3
supports CBS feature at speeds up to 10Gbps

---
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---

Jose Abreu (3):
  net: stmmac: gmac4+: Add Split Header support
  net: stmmac: xgmac: Add C45 PHY support in the MDIO callbacks
  net: stmmac: tc: Remove the speed dependency

 drivers/net/ethernet/stmicro/stmmac/dwmac4.h       |  7 ++++
 drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.c | 21 ++++++++--
 drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.h |  1 +
 drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c   | 19 +++++++++
 drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.h   |  1 +
 drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c  | 47 ++++++++++++++++++++--
 drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c    |  2 -
 7 files changed, 89 insertions(+), 9 deletions(-)

-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next 1/3] net: stmmac: gmac4+: Add Split Header support

[Jose Abreu]

GMAC4+ cores also support the Split Header feature.

Add the support for Split Header feature in the RX path following the
same implementation logic that XGMAC followed.

Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>

---
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---
 drivers/net/ethernet/stmicro/stmmac/dwmac4.h       |  7 +++++++
 drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.c | 21 ++++++++++++++++++---
 drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.h |  1 +
 drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c   | 19 +++++++++++++++++++
 drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.h   |  1 +
 5 files changed, 46 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4.h b/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
index 07e97f45755d..2dc70d104161 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
@@ -14,6 +14,7 @@
 
 /*  MAC registers */
 #define GMAC_CONFIG			0x00000000
+#define GMAC_EXT_CONFIG			0x00000004
 #define GMAC_PACKET_FILTER		0x00000008
 #define GMAC_HASH_TAB(x)		(0x10 + (x) * 4)
 #define GMAC_VLAN_TAG			0x00000050
@@ -188,6 +189,11 @@ enum power_event {
 #define GMAC_CONFIG_TE			BIT(1)
 #define GMAC_CONFIG_RE			BIT(0)
 
+/* MAC extended config */
+#define GMAC_CONFIG_HDSMS		GENMASK(22, 20)
+#define GMAC_CONFIG_HDSMS_SHIFT		20
+#define GMAC_CONFIG_HDSMS_256		(0x2 << GMAC_CONFIG_HDSMS_SHIFT)
+
 /* MAC HW features0 bitmap */
 #define GMAC_HW_FEAT_SAVLANINS		BIT(27)
 #define GMAC_HW_FEAT_ADDMAC		BIT(18)
@@ -211,6 +217,7 @@ enum power_event {
 #define GMAC_HW_HASH_TB_SZ		GENMASK(25, 24)
 #define GMAC_HW_FEAT_AVSEL		BIT(20)
 #define GMAC_HW_TSOEN			BIT(18)
+#define GMAC_HW_FEAT_SPHEN		BIT(17)
 #define GMAC_HW_ADDR64			GENMASK(15, 14)
 #define GMAC_HW_TXFIFOSIZE		GENMASK(10, 6)
 #define GMAC_HW_RXFIFOSIZE		GENMASK(4, 0)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.c b/drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.c
index 707ab5eba8da..3e14da69f378 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.c
@@ -83,9 +83,10 @@ static int dwmac4_wrback_get_rx_status(void *data, struct stmmac_extra_stats *x,
 	if (unlikely(rdes3 & RDES3_OWN))
 		return dma_own;
 
-	/* Verify rx error by looking at the last segment. */
-	if (likely(!(rdes3 & RDES3_LAST_DESCRIPTOR)))
+	if (unlikely(rdes3 & RDES3_CONTEXT_DESCRIPTOR))
 		return discard_frame;
+	if (likely(!(rdes3 & RDES3_LAST_DESCRIPTOR)))
+		return rx_not_ls;
 
 	if (unlikely(rdes3 & RDES3_ERROR_SUMMARY)) {
 		if (unlikely(rdes3 & RDES3_GIANT_PACKET))
@@ -188,7 +189,7 @@ static void dwmac4_set_tx_owner(struct dma_desc *p)
 
 static void dwmac4_set_rx_owner(struct dma_desc *p, int disable_rx_ic)
 {
-	p->des3 = cpu_to_le32(RDES3_OWN | RDES3_BUFFER1_VALID_ADDR);
+	p->des3 |= cpu_to_le32(RDES3_OWN | RDES3_BUFFER1_VALID_ADDR);
 
 	if (!disable_rx_ic)
 		p->des3 |= cpu_to_le32(RDES3_INT_ON_COMPLETION_EN);
@@ -492,6 +493,18 @@ static void dwmac4_set_vlan(struct dma_desc *p, u32 type)
 	p->des2 |= cpu_to_le32(type & TDES2_VLAN_TAG_MASK);
 }
 
+static int dwmac4_get_rx_header_len(struct dma_desc *p, unsigned int *len)
+{
+	*len = le32_to_cpu(p->des2) & RDES2_HL;
+	return 0;
+}
+
+static void dwmac4_set_sec_addr(struct dma_desc *p, dma_addr_t addr)
+{
+	p->des2 = cpu_to_le32(lower_32_bits(addr));
+	p->des3 = cpu_to_le32(upper_32_bits(addr) | RDES3_BUFFER2_VALID_ADDR);
+}
+
 const struct stmmac_desc_ops dwmac4_desc_ops = {
 	.tx_status = dwmac4_wrback_get_tx_status,
 	.rx_status = dwmac4_wrback_get_rx_status,
@@ -519,6 +532,8 @@ const struct stmmac_desc_ops dwmac4_desc_ops = {
 	.set_sarc = dwmac4_set_sarc,
 	.set_vlan_tag = dwmac4_set_vlan_tag,
 	.set_vlan = dwmac4_set_vlan,
+	.get_rx_header_len = dwmac4_get_rx_header_len,
+	.set_sec_addr = dwmac4_set_sec_addr,
 };
 
 const struct stmmac_mode_ops dwmac4_ring_mode_ops = {
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.h b/drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.h
index 0d7b3bbcd5a7..6d92109dc9aa 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.h
@@ -109,6 +109,7 @@
 #define RDES2_L4_FILTER_MATCH		BIT(28)
 #define RDES2_L3_L4_FILT_NB_MATCH_MASK	GENMASK(27, 26)
 #define RDES2_L3_L4_FILT_NB_MATCH_SHIFT	26
+#define RDES2_HL			GENMASK(9, 0)
 
 /* RDES3 (write back format) */
 #define RDES3_PACKET_SIZE_MASK		GENMASK(14, 0)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c b/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c
index b24c89572745..36a0af8bf89f 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c
@@ -368,6 +368,7 @@ static void dwmac4_get_hw_feature(void __iomem *ioaddr,
 	dma_cap->hash_tb_sz = (hw_cap & GMAC_HW_HASH_TB_SZ) >> 24;
 	dma_cap->av = (hw_cap & GMAC_HW_FEAT_AVSEL) >> 20;
 	dma_cap->tsoen = (hw_cap & GMAC_HW_TSOEN) >> 18;
+	dma_cap->sphen = (hw_cap & GMAC_HW_FEAT_SPHEN) >> 17;
 
 	dma_cap->addr64 = (hw_cap & GMAC_HW_ADDR64) >> 14;
 	switch (dma_cap->addr64) {
@@ -460,6 +461,22 @@ static void dwmac4_set_bfsize(void __iomem *ioaddr, int bfsize, u32 chan)
 	writel(value, ioaddr + DMA_CHAN_RX_CONTROL(chan));
 }
 
+static void dwmac4_enable_sph(void __iomem *ioaddr, bool en, u32 chan)
+{
+	u32 value = readl(ioaddr + GMAC_EXT_CONFIG);
+
+	value &= ~GMAC_CONFIG_HDSMS;
+	value |= GMAC_CONFIG_HDSMS_256; /* Segment max 256 bytes */
+	writel(value, ioaddr + GMAC_EXT_CONFIG);
+
+	value = readl(ioaddr + DMA_CHAN_CONTROL(chan));
+	if (en)
+		value |= DMA_CONTROL_SPH;
+	else
+		value &= ~DMA_CONTROL_SPH;
+	writel(value, ioaddr + DMA_CHAN_CONTROL(chan));
+}
+
 const struct stmmac_dma_ops dwmac4_dma_ops = {
 	.reset = dwmac4_dma_reset,
 	.init = dwmac4_dma_init,
@@ -486,6 +503,7 @@ const struct stmmac_dma_ops dwmac4_dma_ops = {
 	.enable_tso = dwmac4_enable_tso,
 	.qmode = dwmac4_qmode,
 	.set_bfsize = dwmac4_set_bfsize,
+	.enable_sph = dwmac4_enable_sph,
 };
 
 const struct stmmac_dma_ops dwmac410_dma_ops = {
@@ -514,4 +532,5 @@ const struct stmmac_dma_ops dwmac410_dma_ops = {
 	.enable_tso = dwmac4_enable_tso,
 	.qmode = dwmac4_qmode,
 	.set_bfsize = dwmac4_set_bfsize,
+	.enable_sph = dwmac4_enable_sph,
 };
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.h b/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.h
index 5299fa1001a3..589931795847 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.h
@@ -110,6 +110,7 @@
 #define DMA_CHAN_STATUS(x)		(DMA_CHANX_BASE_ADDR(x) + 0x60)
 
 /* DMA Control X */
+#define DMA_CONTROL_SPH			BIT(24)
 #define DMA_CONTROL_MSS_MASK		GENMASK(13, 0)
 
 /* DMA Tx Channel X Control register defines */
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next 2/3] net: stmmac: xgmac: Add C45 PHY support in the MDIO callbacks

[Jose Abreu]

Add the support for C45 PHYs in the MDIO callbacks for XGMAC. This was
tested using Synopsys DesignWare XPCS.

Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>

---
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---
 drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 47 +++++++++++++++++++++--
 1 file changed, 43 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 40c42637ad75..143bffd28acf 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -41,6 +41,29 @@
 #define MII_XGMAC_BUSY			BIT(22)
 #define MII_XGMAC_MAX_C22ADDR		3
 #define MII_XGMAC_C22P_MASK		GENMASK(MII_XGMAC_MAX_C22ADDR, 0)
+#define MII_XGMAC_PA_SHIFT		16
+#define MII_XGMAC_DA_SHIFT		21
+
+static int stmmac_xgmac2_c45_format(struct stmmac_priv *priv, int phyaddr,
+				    int phyreg, u32 *hw_addr)
+{
+	unsigned int mii_data = priv->hw->mii.data;
+	u32 tmp;
+
+	/* Wait until any existing MII operation is complete */
+	if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
+			       !(tmp & MII_XGMAC_BUSY), 100, 10000))
+		return -EBUSY;
+
+	/* Set port as Clause 45 */
+	tmp = readl(priv->ioaddr + XGMAC_MDIO_C22P);
+	tmp &= ~BIT(phyaddr);
+	writel(tmp, priv->ioaddr + XGMAC_MDIO_C22P);
+
+	*hw_addr = (phyaddr << MII_XGMAC_PA_SHIFT) | (phyreg & 0xffff);
+	*hw_addr |= (phyreg >> MII_DEVADDR_C45_SHIFT) << MII_XGMAC_DA_SHIFT;
+	return 0;
+}
 
 static int stmmac_xgmac2_c22_format(struct stmmac_priv *priv, int phyaddr,
 				    int phyreg, u32 *hw_addr)
@@ -76,16 +99,22 @@ static int stmmac_xgmac2_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg)
 	int ret;
 
 	if (phyreg & MII_ADDR_C45) {
-		return -EOPNOTSUPP;
+		phyreg &= ~MII_ADDR_C45;
+
+		ret = stmmac_xgmac2_c45_format(priv, phyaddr, phyreg, &addr);
+		if (ret)
+			return ret;
 	} else {
 		ret = stmmac_xgmac2_c22_format(priv, phyaddr, phyreg, &addr);
 		if (ret)
 			return ret;
+
+		value |= MII_XGMAC_SADDR;
 	}
 
 	value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
 		& priv->hw->mii.clk_csr_mask;
-	value |= MII_XGMAC_SADDR | MII_XGMAC_READ;
+	value |= MII_XGMAC_READ;
 
 	/* Wait until any existing MII operation is complete */
 	if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
@@ -116,16 +145,22 @@ static int stmmac_xgmac2_mdio_write(struct mii_bus *bus, int phyaddr,
 	int ret;
 
 	if (phyreg & MII_ADDR_C45) {
-		return -EOPNOTSUPP;
+		phyreg &= ~MII_ADDR_C45;
+
+		ret = stmmac_xgmac2_c45_format(priv, phyaddr, phyreg, &addr);
+		if (ret)
+			return ret;
 	} else {
 		ret = stmmac_xgmac2_c22_format(priv, phyaddr, phyreg, &addr);
 		if (ret)
 			return ret;
+
+		value |= MII_XGMAC_SADDR;
 	}
 
 	value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
 		& priv->hw->mii.clk_csr_mask;
-	value |= phydata | MII_XGMAC_SADDR;
+	value |= phydata;
 	value |= MII_XGMAC_WRITE;
 
 	/* Wait until any existing MII operation is complete */
@@ -363,6 +398,10 @@ int stmmac_mdio_register(struct net_device *ndev)
 		goto bus_register_fail;
 	}
 
+	/* Looks like we need a dummy read for XGMAC only and C45 PHYs */
+	if (priv->plat->has_xgmac)
+		stmmac_xgmac2_mdio_read(new_bus, 0, MII_ADDR_C45);
+
 	if (priv->plat->phy_node || mdio_node)
 		goto bus_register_done;
 
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH net-next 2/3] net: stmmac: xgmac: Add C45 PHY support in the MDIO callbacks

[Andrew Lunn]

On Wed, Oct 30, 2019 at 04:28:49PM +0100, Jose Abreu wrote:
> Add the support for C45 PHYs in the MDIO callbacks for XGMAC. This was
> tested using Synopsys DesignWare XPCS.
> 
> Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
> 
> ---
> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Jose Abreu <joabreu@synopsys.com>
> Cc: "David S. Miller" <davem@davemloft.net>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: netdev@vger.kernel.org
> Cc: linux-stm32@st-md-mailman.stormreply.com
> Cc: linux-arm-kernel@lists.infradead.org
> Cc: linux-kernel@vger.kernel.org
> ---
>  drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 47 +++++++++++++++++++++--
>  1 file changed, 43 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
> index 40c42637ad75..143bffd28acf 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
> @@ -41,6 +41,29 @@
>  #define MII_XGMAC_BUSY			BIT(22)
>  #define MII_XGMAC_MAX_C22ADDR		3
>  #define MII_XGMAC_C22P_MASK		GENMASK(MII_XGMAC_MAX_C22ADDR, 0)
> +#define MII_XGMAC_PA_SHIFT		16
> +#define MII_XGMAC_DA_SHIFT		21
> +
> +static int stmmac_xgmac2_c45_format(struct stmmac_priv *priv, int phyaddr,
> +				    int phyreg, u32 *hw_addr)
> +{
> +	unsigned int mii_data = priv->hw->mii.data;
> +	u32 tmp;
> +
> +	/* Wait until any existing MII operation is complete */
> +	if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
> +			       !(tmp & MII_XGMAC_BUSY), 100, 10000))
> +		return -EBUSY;

Hi Jose

The stmmac_xgmac2_c22_format function does the same. Maybe the call
can be pulled out into stmmac_xgmac2_mdio_write() and
stmmac_xgmac2_mdio_read()?

	Andrew

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next 3/3] net: stmmac: tc: Remove the speed dependency

[Jose Abreu]

XGMAC3 supports full CBS features with speeds that can go up to 10G so
we can now remove the maximum speed check of CBS.

Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>

---
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---
 drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
index f9a9a9d82233..7d972e0fd2b0 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
@@ -321,8 +321,6 @@ static int tc_setup_cbs(struct stmmac_priv *priv,
 		return -EINVAL;
 	if (!priv->dma_cap.av)
 		return -EOPNOTSUPP;
-	if (priv->speed != SPEED_100 && priv->speed != SPEED_1000)
-		return -EOPNOTSUPP;
 
 	mode_to_use = priv->plat->tx_queues_cfg[queue].mode_to_use;
 	if (mode_to_use == MTL_QUEUE_DCB && qopt->enable) {
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel