linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
* [PATCH v5 0/8] Add support for Hikey 970 PCIe
@ 2021-07-13  6:28 Mauro Carvalho Chehab
  2021-07-13  6:28 ` [PATCH v5 7/8] PCI: kirin: Drop the PHY logic from the driver Mauro Carvalho Chehab
  0 siblings, 1 reply; 2+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-13  6:28 UTC (permalink / raw)
  To: Bjorn Helgaas
  Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
	Manivannan Sadhasivam, Rob Herring, Krzysztof Wilczyński,
	Binghui Wang, Rob Herring, Xiaowei Song, devicetree,
	linux-arm-kernel, linux-kernel, linux-pci, linux-phy

As requested by Rob Herring, this series split the PHY part into a separate driver.
Then, it adds support for Kirin 970 on a single patch.

With this change, the PHY-specific device tree bindings for Kirin 960 moved
to its own PHY properties.

Tested on Hikey970:

  $ lspci
  00:00.0 PCI bridge: Huawei Technologies Co., Ltd. Device 3670 (rev 01)
  01:00.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
  02:01.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
  02:04.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
  02:05.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
  02:07.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
  02:09.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
  06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 07)

  $ ethtool enp6s0
  Settings for enp6s0:
	Supported ports: [ TP	 MII ]
	Supported link modes:   10baseT/Half 10baseT/Full
	                        100baseT/Half 100baseT/Full
	                        1000baseT/Half 1000baseT/Full
	Supported pause frame use: Symmetric Receive-only
	Supports auto-negotiation: Yes
	Supported FEC modes: Not reported
	Advertised link modes:  10baseT/Half 10baseT/Full
	                        100baseT/Half 100baseT/Full
	                        1000baseT/Half 1000baseT/Full
	Advertised pause frame use: Symmetric Receive-only
	Advertised auto-negotiation: Yes
	Advertised FEC modes: Not reported
	Link partner advertised link modes:  10baseT/Half 10baseT/Full
	                                     100baseT/Half 100baseT/Full
	Link partner advertised pause frame use: Symmetric Receive-only
	Link partner advertised auto-negotiation: Yes
	Link partner advertised FEC modes: Not reported
	Speed: 100Mb/s
	Duplex: Full
	Auto-negotiation: on
	master-slave cfg: preferred slave
	master-slave status: slave
	Port: Twisted Pair
	PHYAD: 0
	Transceiver: external
	MDI-X: Unknown
  netlink error: Operation not permitted
	Link detected: yes

Partially tested on Hikey 960[1]:

  $ lspci
  00:00.0 PCI bridge: Huawei Technologies Co., Ltd. Device 3660 (rev 01)

[1] The Hikey 960 doesn't come with any internal PCIe device.
    Its hardware supports just an external device via a M.2 slot that
    doesn't support SATA. I ordered a NVMe device to test, but the vendor
    is currently out of supply. It should take 3-4 weeks to arrive here. I'll
    run an extra test on it once it arrives.

---

v5:
- added "static" to hi3670_pcie_get_eyeparam() declaration on patch 6/8

v4:

- dropped the DTS patch, as it depends on a PMIC-related patch series;
- minor changes at the patch description;
- HiKey and HiSilicon are now using the preferred CamelCase format.


Mauro Carvalho Chehab (8):
  dt-bindings: phy: Add bindings for HiKey 960 PCIe PHY
  dt-bindings: phy: Add bindings for HiKey 970 PCIe PHY
  dt-bindings: PCI: kirin: Fix compatible string
  dt-bindings: PCI: kirin: Drop PHY properties
  phy: HiSilicon: Add driver for Kirin 960 PCIe PHY
  phy: HiSilicon: add driver for Kirin 970 PCIe PHY
  PCI: kirin: Drop the PHY logic from the driver
  PCI: kirin: Use regmap for APB registers

 .../devicetree/bindings/pci/kirin-pcie.txt    |  21 +-
 .../phy/hisilicon,phy-hi3660-pcie.yaml        |  82 ++
 .../phy/hisilicon,phy-hi3670-pcie.yaml        | 101 ++
 arch/arm64/boot/dts/hisilicon/hi3660.dtsi     |  29 +-
 drivers/pci/controller/dwc/pcie-kirin.c       | 298 ++----
 drivers/phy/hisilicon/Kconfig                 |  20 +
 drivers/phy/hisilicon/Makefile                |   2 +
 drivers/phy/hisilicon/phy-hi3660-pcie.c       | 325 +++++++
 drivers/phy/hisilicon/phy-hi3670-pcie.c       | 892 ++++++++++++++++++
 9 files changed, 1500 insertions(+), 270 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/phy/hisilicon,phy-hi3660-pcie.yaml
 create mode 100644 Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml
 create mode 100644 drivers/phy/hisilicon/phy-hi3660-pcie.c
 create mode 100644 drivers/phy/hisilicon/phy-hi3670-pcie.c

-- 
2.31.1



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 2+ messages in thread

* [PATCH v5 7/8] PCI: kirin: Drop the PHY logic from the driver
  2021-07-13  6:28 [PATCH v5 0/8] Add support for Hikey 970 PCIe Mauro Carvalho Chehab
@ 2021-07-13  6:28 ` Mauro Carvalho Chehab
  0 siblings, 0 replies; 2+ messages in thread
From: Mauro Carvalho Chehab @ 2021-07-13  6:28 UTC (permalink / raw)
  To: Bjorn Helgaas
  Cc: linuxarm, mauro.chehab, Mauro Carvalho Chehab,
	Krzysztof Wilczyński, Manivannan Sadhasivam, Rob Herring,
	Binghui Wang, Bjorn Helgaas, Lorenzo Pieralisi, Rob Herring,
	Wei Xu, Xiaowei Song, devicetree, linux-arm-kernel, linux-kernel,
	linux-pci

The pcie-kirin PCIe driver contains internally a PHY interface for
a Kirin 960. Drop it and add support for using the new PHY driver
for Kirin 960, updating DT accordingly.

Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
 arch/arm64/boot/dts/hisilicon/hi3660.dtsi |  29 ++-
 drivers/pci/controller/dwc/pcie-kirin.c   | 252 +++-------------------
 2 files changed, 47 insertions(+), 234 deletions(-)

diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
index f1ec87c05842..772bb632814f 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
@@ -995,17 +995,33 @@ spi3: spi@ff3b3000 {
 			status = "disabled";
 		};
 
+		pcie_phy: pcie-phy@f3f2000 {
+			compatible = "hisilicon,hi960-pcie-phy";
+			reg = <0x0 0xf3f20000 0x0 0x40000>;
+			reg-names = "phy";
+			clocks = <&crg_ctrl HI3660_PCIEPHY_REF>,
+				 <&crg_ctrl HI3660_CLK_GATE_PCIEAUX>,
+				 <&crg_ctrl HI3660_PCLK_GATE_PCIE_PHY>,
+				 <&crg_ctrl HI3660_PCLK_GATE_PCIE_SYS>,
+				 <&crg_ctrl HI3660_ACLK_GATE_PCIE>;
+			clock-names = "pcie_phy_ref", "pcie_aux",
+				      "pcie_apb_phy", "pcie_apb_sys",
+				      "pcie_aclk";
+			reset-gpios = <&gpio11 1 0 >;
+			#phy-cells = <0>;
+		};
+
 		pcie@f4000000 {
 			compatible = "hisilicon,kirin960-pcie";
 			reg = <0x0 0xf4000000 0x0 0x1000>,
 			      <0x0 0xff3fe000 0x0 0x1000>,
-			      <0x0 0xf3f20000 0x0 0x40000>,
 			      <0x0 0xf5000000 0x0 0x2000>;
-			reg-names = "dbi", "apb", "phy", "config";
+			reg-names = "dbi", "apb", "config";
 			bus-range = <0x0  0x1>;
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
+			phys = <&pcie_phy>;
 			ranges = <0x02000000 0x0 0x00000000
 				  0x0 0xf6000000
 				  0x0 0x02000000>;
@@ -1022,15 +1038,6 @@ &gic GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
 					 &gic GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
 					<0x0 0 0 4
 					 &gic GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&crg_ctrl HI3660_PCIEPHY_REF>,
-				 <&crg_ctrl HI3660_CLK_GATE_PCIEAUX>,
-				 <&crg_ctrl HI3660_PCLK_GATE_PCIE_PHY>,
-				 <&crg_ctrl HI3660_PCLK_GATE_PCIE_SYS>,
-				 <&crg_ctrl HI3660_ACLK_GATE_PCIE>;
-			clock-names = "pcie_phy_ref", "pcie_aux",
-				      "pcie_apb_phy", "pcie_apb_sys",
-				      "pcie_aclk";
-			reset-gpios = <&gpio11 1 0 >;
 		};
 
 		/* UFS */
diff --git a/drivers/pci/controller/dwc/pcie-kirin.c b/drivers/pci/controller/dwc/pcie-kirin.c
index 7b0f87535960..66662f7b0fc9 100644
--- a/drivers/pci/controller/dwc/pcie-kirin.c
+++ b/drivers/pci/controller/dwc/pcie-kirin.c
@@ -9,7 +9,6 @@
  */
 
 #include <linux/compiler.h>
-#include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/err.h>
 #include <linux/gpio.h>
@@ -21,6 +20,7 @@
 #include <linux/pci.h>
 #include <linux/pci_regs.h>
 #include <linux/platform_device.h>
+#include <linux/phy/phy.h>
 #include <linux/regmap.h>
 #include <linux/resource.h>
 #include <linux/types.h>
@@ -28,26 +28,17 @@
 
 #define to_kirin_pcie(x) dev_get_drvdata((x)->dev)
 
-#define REF_CLK_FREQ			100000000
-
 /* PCIe ELBI registers */
 #define SOC_PCIECTRL_CTRL0_ADDR		0x000
 #define SOC_PCIECTRL_CTRL1_ADDR		0x004
-#define SOC_PCIEPHY_CTRL2_ADDR		0x008
-#define SOC_PCIEPHY_CTRL3_ADDR		0x00c
 #define PCIE_ELBI_SLV_DBI_ENABLE	(0x1 << 21)
 
 /* info located in APB */
 #define PCIE_APP_LTSSM_ENABLE	0x01c
-#define PCIE_APB_PHY_CTRL0	0x0
-#define PCIE_APB_PHY_CTRL1	0x4
 #define PCIE_APB_PHY_STATUS0	0x400
 #define PCIE_LINKUP_ENABLE	(0x8020)
 #define PCIE_LTSSM_ENABLE_BIT	(0x1 << 11)
 #define PIPE_CLK_STABLE		(0x1 << 19)
-#define PHY_REF_PAD_BIT		(0x1 << 8)
-#define PHY_PWR_DOWN_BIT	(0x1 << 22)
-#define PHY_RST_ACK_BIT		(0x1 << 16)
 
 /* info located in sysctrl */
 #define SCTRL_PCIE_CMOS_OFFSET	0x60
@@ -60,36 +51,10 @@
 #define PCIE_DEBOUNCE_PARAM	0xF0F400
 #define PCIE_OE_BYPASS		(0x3 << 28)
 
-/* peri_crg ctrl */
-#define CRGCTRL_PCIE_ASSERT_OFFSET	0x88
-#define CRGCTRL_PCIE_ASSERT_BIT		0x8c000000
-
-/* Time for delay */
-#define REF_2_PERST_MIN		20000
-#define REF_2_PERST_MAX		25000
-#define PERST_2_ACCESS_MIN	10000
-#define PERST_2_ACCESS_MAX	12000
-#define LINK_WAIT_MIN		900
-#define LINK_WAIT_MAX		1000
-#define PIPE_CLK_WAIT_MIN	550
-#define PIPE_CLK_WAIT_MAX	600
-#define TIME_CMOS_MIN		100
-#define TIME_CMOS_MAX		105
-#define TIME_PHY_PD_MIN		10
-#define TIME_PHY_PD_MAX		11
-
 struct kirin_pcie {
 	struct dw_pcie	*pci;
+	struct phy	*phy;
 	void __iomem	*apb_base;
-	void __iomem	*phy_base;
-	struct regmap	*crgctrl;
-	struct regmap	*sysctrl;
-	struct clk	*apb_sys_clk;
-	struct clk	*apb_phy_clk;
-	struct clk	*phy_ref_clk;
-	struct clk	*pcie_aclk;
-	struct clk	*pcie_aux_clk;
-	int		gpio_id_reset;
 };
 
 /* Registers in PCIeCTRL */
@@ -104,46 +69,6 @@ static inline u32 kirin_apb_ctrl_readl(struct kirin_pcie *kirin_pcie, u32 reg)
 	return readl(kirin_pcie->apb_base + reg);
 }
 
-/* Registers in PCIePHY */
-static inline void kirin_apb_phy_writel(struct kirin_pcie *kirin_pcie,
-					u32 val, u32 reg)
-{
-	writel(val, kirin_pcie->phy_base + reg);
-}
-
-static inline u32 kirin_apb_phy_readl(struct kirin_pcie *kirin_pcie, u32 reg)
-{
-	return readl(kirin_pcie->phy_base + reg);
-}
-
-static long kirin_pcie_get_clk(struct kirin_pcie *kirin_pcie,
-			       struct platform_device *pdev)
-{
-	struct device *dev = &pdev->dev;
-
-	kirin_pcie->phy_ref_clk = devm_clk_get(dev, "pcie_phy_ref");
-	if (IS_ERR(kirin_pcie->phy_ref_clk))
-		return PTR_ERR(kirin_pcie->phy_ref_clk);
-
-	kirin_pcie->pcie_aux_clk = devm_clk_get(dev, "pcie_aux");
-	if (IS_ERR(kirin_pcie->pcie_aux_clk))
-		return PTR_ERR(kirin_pcie->pcie_aux_clk);
-
-	kirin_pcie->apb_phy_clk = devm_clk_get(dev, "pcie_apb_phy");
-	if (IS_ERR(kirin_pcie->apb_phy_clk))
-		return PTR_ERR(kirin_pcie->apb_phy_clk);
-
-	kirin_pcie->apb_sys_clk = devm_clk_get(dev, "pcie_apb_sys");
-	if (IS_ERR(kirin_pcie->apb_sys_clk))
-		return PTR_ERR(kirin_pcie->apb_sys_clk);
-
-	kirin_pcie->pcie_aclk = devm_clk_get(dev, "pcie_aclk");
-	if (IS_ERR(kirin_pcie->pcie_aclk))
-		return PTR_ERR(kirin_pcie->pcie_aclk);
-
-	return 0;
-}
-
 static long kirin_pcie_get_resource(struct kirin_pcie *kirin_pcie,
 				    struct platform_device *pdev)
 {
@@ -152,149 +77,18 @@ static long kirin_pcie_get_resource(struct kirin_pcie *kirin_pcie,
 	if (IS_ERR(kirin_pcie->apb_base))
 		return PTR_ERR(kirin_pcie->apb_base);
 
-	kirin_pcie->phy_base =
-		devm_platform_ioremap_resource_byname(pdev, "phy");
-	if (IS_ERR(kirin_pcie->phy_base))
-		return PTR_ERR(kirin_pcie->phy_base);
-
-	kirin_pcie->crgctrl =
-		syscon_regmap_lookup_by_compatible("hisilicon,hi3660-crgctrl");
-	if (IS_ERR(kirin_pcie->crgctrl))
-		return PTR_ERR(kirin_pcie->crgctrl);
-
-	kirin_pcie->sysctrl =
-		syscon_regmap_lookup_by_compatible("hisilicon,hi3660-sctrl");
-	if (IS_ERR(kirin_pcie->sysctrl))
-		return PTR_ERR(kirin_pcie->sysctrl);
-
 	return 0;
 }
 
-static int kirin_pcie_phy_init(struct kirin_pcie *kirin_pcie)
-{
-	struct device *dev = kirin_pcie->pci->dev;
-	u32 reg_val;
-
-	reg_val = kirin_apb_phy_readl(kirin_pcie, PCIE_APB_PHY_CTRL1);
-	reg_val &= ~PHY_REF_PAD_BIT;
-	kirin_apb_phy_writel(kirin_pcie, reg_val, PCIE_APB_PHY_CTRL1);
-
-	reg_val = kirin_apb_phy_readl(kirin_pcie, PCIE_APB_PHY_CTRL0);
-	reg_val &= ~PHY_PWR_DOWN_BIT;
-	kirin_apb_phy_writel(kirin_pcie, reg_val, PCIE_APB_PHY_CTRL0);
-	usleep_range(TIME_PHY_PD_MIN, TIME_PHY_PD_MAX);
-
-	reg_val = kirin_apb_phy_readl(kirin_pcie, PCIE_APB_PHY_CTRL1);
-	reg_val &= ~PHY_RST_ACK_BIT;
-	kirin_apb_phy_writel(kirin_pcie, reg_val, PCIE_APB_PHY_CTRL1);
-
-	usleep_range(PIPE_CLK_WAIT_MIN, PIPE_CLK_WAIT_MAX);
-	reg_val = kirin_apb_phy_readl(kirin_pcie, PCIE_APB_PHY_STATUS0);
-	if (reg_val & PIPE_CLK_STABLE) {
-		dev_err(dev, "PIPE clk is not stable\n");
-		return -EINVAL;
-	}
-
-	return 0;
-}
-
-static void kirin_pcie_oe_enable(struct kirin_pcie *kirin_pcie)
-{
-	u32 val;
-
-	regmap_read(kirin_pcie->sysctrl, SCTRL_PCIE_OE_OFFSET, &val);
-	val |= PCIE_DEBOUNCE_PARAM;
-	val &= ~PCIE_OE_BYPASS;
-	regmap_write(kirin_pcie->sysctrl, SCTRL_PCIE_OE_OFFSET, val);
-}
-
-static int kirin_pcie_clk_ctrl(struct kirin_pcie *kirin_pcie, bool enable)
-{
-	int ret = 0;
-
-	if (!enable)
-		goto close_clk;
-
-	ret = clk_set_rate(kirin_pcie->phy_ref_clk, REF_CLK_FREQ);
-	if (ret)
-		return ret;
-
-	ret = clk_prepare_enable(kirin_pcie->phy_ref_clk);
-	if (ret)
-		return ret;
-
-	ret = clk_prepare_enable(kirin_pcie->apb_sys_clk);
-	if (ret)
-		goto apb_sys_fail;
-
-	ret = clk_prepare_enable(kirin_pcie->apb_phy_clk);
-	if (ret)
-		goto apb_phy_fail;
-
-	ret = clk_prepare_enable(kirin_pcie->pcie_aclk);
-	if (ret)
-		goto aclk_fail;
-
-	ret = clk_prepare_enable(kirin_pcie->pcie_aux_clk);
-	if (ret)
-		goto aux_clk_fail;
-
-	return 0;
-
-close_clk:
-	clk_disable_unprepare(kirin_pcie->pcie_aux_clk);
-aux_clk_fail:
-	clk_disable_unprepare(kirin_pcie->pcie_aclk);
-aclk_fail:
-	clk_disable_unprepare(kirin_pcie->apb_phy_clk);
-apb_phy_fail:
-	clk_disable_unprepare(kirin_pcie->apb_sys_clk);
-apb_sys_fail:
-	clk_disable_unprepare(kirin_pcie->phy_ref_clk);
-
-	return ret;
-}
-
 static int kirin_pcie_power_on(struct kirin_pcie *kirin_pcie)
 {
 	int ret;
 
-	/* Power supply for Host */
-	regmap_write(kirin_pcie->sysctrl,
-		     SCTRL_PCIE_CMOS_OFFSET, SCTRL_PCIE_CMOS_BIT);
-	usleep_range(TIME_CMOS_MIN, TIME_CMOS_MAX);
-	kirin_pcie_oe_enable(kirin_pcie);
-
-	ret = kirin_pcie_clk_ctrl(kirin_pcie, true);
+	ret = phy_init(kirin_pcie->phy);
 	if (ret)
 		return ret;
 
-	/* ISO disable, PCIeCtrl, PHY assert and clk gate clear */
-	regmap_write(kirin_pcie->sysctrl,
-		     SCTRL_PCIE_ISO_OFFSET, SCTRL_PCIE_ISO_BIT);
-	regmap_write(kirin_pcie->crgctrl,
-		     CRGCTRL_PCIE_ASSERT_OFFSET, CRGCTRL_PCIE_ASSERT_BIT);
-	regmap_write(kirin_pcie->sysctrl,
-		     SCTRL_PCIE_HPCLK_OFFSET, SCTRL_PCIE_HPCLK_BIT);
-
-	ret = kirin_pcie_phy_init(kirin_pcie);
-	if (ret)
-		goto close_clk;
-
-	/* perst assert Endpoint */
-	if (!gpio_request(kirin_pcie->gpio_id_reset, "pcie_perst")) {
-		usleep_range(REF_2_PERST_MIN, REF_2_PERST_MAX);
-		ret = gpio_direction_output(kirin_pcie->gpio_id_reset, 1);
-		if (ret)
-			goto close_clk;
-		usleep_range(PERST_2_ACCESS_MIN, PERST_2_ACCESS_MAX);
-
-		return 0;
-	}
-
-close_clk:
-	kirin_pcie_clk_ctrl(kirin_pcie, false);
-	return ret;
+	return phy_power_on(kirin_pcie->phy);
 }
 
 static void kirin_pcie_sideband_dbi_w_mode(struct kirin_pcie *kirin_pcie,
@@ -444,30 +238,41 @@ static int kirin_pcie_probe(struct platform_device *pdev)
 	pci->pp.ops = &kirin_pcie_host_ops;
 	kirin_pcie->pci = pci;
 
-	ret = kirin_pcie_get_clk(kirin_pcie, pdev);
-	if (ret)
-		return ret;
+	kirin_pcie->phy = devm_of_phy_get(dev, dev->of_node, NULL);
+	if (IS_ERR(kirin_pcie->phy))
+		return PTR_ERR(kirin_pcie->phy);
 
 	ret = kirin_pcie_get_resource(kirin_pcie, pdev);
 	if (ret)
 		return ret;
 
-	kirin_pcie->gpio_id_reset = of_get_named_gpio(dev->of_node,
-						      "reset-gpios", 0);
-	if (kirin_pcie->gpio_id_reset == -EPROBE_DEFER) {
-		return -EPROBE_DEFER;
-	} else if (!gpio_is_valid(kirin_pcie->gpio_id_reset)) {
-		dev_err(dev, "unable to get a valid gpio pin\n");
-		return -ENODEV;
-	}
-
 	ret = kirin_pcie_power_on(kirin_pcie);
 	if (ret)
 		return ret;
 
 	platform_set_drvdata(pdev, kirin_pcie);
 
-	return dw_pcie_host_init(&pci->pp);
+	ret = dw_pcie_host_init(&pci->pp);
+	if (ret) {
+		phy_power_off(kirin_pcie->phy);
+		goto err;
+	}
+
+	return 0;
+err:
+	phy_exit(kirin_pcie->phy);
+
+	return ret;
+}
+
+static int __exit kirin_pcie_remove(struct platform_device *pdev)
+{
+	struct kirin_pcie *kirin_pcie = platform_get_drvdata(pdev);
+
+	phy_power_off(kirin_pcie->phy);
+	phy_exit(kirin_pcie->phy);
+
+	return 0;
 }
 
 static const struct of_device_id kirin_pcie_match[] = {
@@ -478,6 +283,7 @@ static const struct of_device_id kirin_pcie_match[] = {
 
 static struct platform_driver kirin_pcie_driver = {
 	.probe			= kirin_pcie_probe,
+	.remove	        	= __exit_p(kirin_pcie_remove),
 	.driver			= {
 		.name			= "kirin-pcie",
 		.of_match_table = kirin_pcie_match,
-- 
2.31.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 2+ messages in thread

end of thread, other threads:[~2021-07-13  6:31 UTC | newest]

Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-07-13  6:28 [PATCH v5 0/8] Add support for Hikey 970 PCIe Mauro Carvalho Chehab
2021-07-13  6:28 ` [PATCH v5 7/8] PCI: kirin: Drop the PHY logic from the driver Mauro Carvalho Chehab

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).