linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Prasad Malisetty <pmaliset@codeaurora.org>
To: agross@kernel.org, bjorn.andersson@linaro.org,
	bhelgaas@google.com, robh+dt@kernel.org, swboyd@chromium.org,
	lorenzo.pieralisi@arm.com, svarbanov@mm-sol.com
Cc: devicetree@vger.kernel.org, linux-arm-msm@vger.kernel.org,
	linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org,
	dianders@chromium.org, mka@chromium.org, vbadigan@codeaurora.org,
	sallenki@codeaurora.org, manivannan.sadhasivam@linaro.org,
	Prasad Malisetty <pmaliset@codeaurora.org>
Subject: [PATCH v8 2/4] arm64: dts: qcom: sc7280: Add PCIe and PHY related nodes
Date: Fri, 17 Sep 2021 22:45:45 +0530	[thread overview]
Message-ID: <1631898947-27433-3-git-send-email-pmaliset@codeaurora.org> (raw)
In-Reply-To: <1631898947-27433-1-git-send-email-pmaliset@codeaurora.org>

Add PCIe controller and PHY nodes for sc7280 SOC.

Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 120 +++++++++++++++++++++++++++++++++++
 1 file changed, 120 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index fd78f16..1ce0847 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -7,6 +7,7 @@
 
 #include <dt-bindings/clock/qcom,gcc-sc7280.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interconnect/qcom,sc7280.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
@@ -586,6 +587,117 @@
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
+		pcie1: pci@1c08000 {
+			compatible = "qcom,pcie-sc7280";
+			reg = <0 0x01c08000 0 0x3000>,
+			      <0 0x40000000 0 0xf1d>,
+			      <0 0x40000f20 0 0xa8>,
+			      <0 0x40001000 0 0x1000>,
+			      <0 0x40100000 0 0x100000>;
+
+			reg-names = "parf", "dbi", "elbi", "atu", "config";
+			device_type = "pci";
+			linux,pci-domain = <1>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
+
+			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
+				 <&gcc GCC_PCIE_1_PIPE_CLK_SRC>,
+				 <&pcie1_lane 0>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
+				 <&gcc GCC_DDRSS_PCIE_SF_CLK>;
+
+			clock-names = "pipe",
+				      "pipe_mux",
+				      "phy_pipe",
+				      "ref",
+				      "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "tbu",
+				      "ddrss_sf_tbu";
+
+			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			resets = <&gcc GCC_PCIE_1_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc GCC_PCIE_1_GDSC>;
+
+			phys = <&pcie1_lane>;
+			phy-names = "pciephy";
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pcie1_default_state>;
+
+			iommus = <&apps_smmu 0x1c80 0x1>;
+
+			iommu-map = <0x0 &apps_smmu 0x1c80 0x1>,
+				    <0x100 &apps_smmu 0x1c81 0x1>;
+
+			status = "disabled";
+		};
+
+		pcie1_phy: phy@1c0e000 {
+			compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy";
+			reg = <0 0x01c0e000 0 0x1c0>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_CLKREF_EN>,
+				 <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+			resets = <&gcc GCC_PCIE_1_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			status = "disabled";
+
+			pcie1_lane: lanes@1c0e200 {
+				reg = <0 0x01c0e200 0 0x170>,
+				      <0 0x01c0e400 0 0x200>,
+				      <0 0x01c0ea00 0 0x1f0>,
+				      <0 0x01c0e600 0 0x170>,
+				      <0 0x01c0e800 0 0x200>,
+				      <0 0x01c0ee00 0 0xf4>;
+				clocks = <&gcc GCC_PCIE_1_PIPE_CLK>;
+				clock-names = "pipe0";
+
+				#phy-cells = <0>;
+				#clock-cells = <1>;
+				clock-output-names = "pcie_1_pipe_clk";
+			};
+		};
+
 		ipa: ipa@1e40000 {
 			compatible = "qcom,sc7280-ipa";
 
@@ -1513,6 +1625,14 @@
 			gpio-ranges = <&tlmm 0 0 175>;
 			wakeup-parent = <&pdc>;
 
+			pcie1_default_state: pcie1-default-state {
+				clkreq {
+					pins = "gpio79";
+					function = "pcie1_clkreqn";
+					bias-pull-up;
+				};
+			};
+
 			qup_uart5_default: qup-uart5-default {
 				pins = "gpio46", "gpio47";
 				function = "qup13";
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project


  parent reply	other threads:[~2021-09-17 17:16 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-09-17 17:15 [PATCH v8 0/4] Add DT bindings and DT nodes for PCIe and PHY in SC7280 Prasad Malisetty
2021-09-17 17:15 ` [PATCH v8 1/4] dt-bindings: pci: qcom: Document PCIe bindings for SC7280 Prasad Malisetty
2021-09-17 17:15 ` Prasad Malisetty [this message]
2021-09-17 17:15 ` [PATCH v8 3/4] arm64: dts: qcom: sc7280: Add PCIe nodes for IDP board Prasad Malisetty
2021-09-20 19:51   ` Stephen Boyd
2021-09-28 13:36     ` Prasad Malisetty
2021-09-17 17:15 ` [PATCH v8 4/4] PCI: qcom: Switch pcie_1_pipe_clk_src after PHY init in SC7280 Prasad Malisetty
2021-09-20 19:53   ` Stephen Boyd
2021-09-23 10:01     ` Prasad Malisetty

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1631898947-27433-3-git-send-email-pmaliset@codeaurora.org \
    --to=pmaliset@codeaurora.org \
    --cc=agross@kernel.org \
    --cc=bhelgaas@google.com \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dianders@chromium.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=lorenzo.pieralisi@arm.com \
    --cc=manivannan.sadhasivam@linaro.org \
    --cc=mka@chromium.org \
    --cc=robh+dt@kernel.org \
    --cc=sallenki@codeaurora.org \
    --cc=svarbanov@mm-sol.com \
    --cc=swboyd@chromium.org \
    --cc=vbadigan@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).