* [PATCH 1/5] ARM: dts: qcom: Replace gpio node with pinctrl node
2015-06-16 20:31 [PATCH 0/5] Enable SPI ethernet on MSM8960 CDP Stephen Boyd
@ 2015-06-16 20:31 ` Stephen Boyd
2015-07-23 20:59 ` Andy Gross
2015-06-16 20:31 ` [PATCH 2/5] ARM: dts: qcom: Add MSM8960 RPM and RPM regulator nodes Stephen Boyd
` (3 subsequent siblings)
4 siblings, 1 reply; 11+ messages in thread
From: Stephen Boyd @ 2015-06-16 20:31 UTC (permalink / raw)
To: Andy Gross; +Cc: linux-kernel, linux-arm-msm, linux-arm-kernel
Now that we have a proper pinctrl driver for the gpio block we
can change the compatible field here and configure the pinmux on
msm8960 devices.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
arch/arm/boot/dts/qcom-msm8960.dtsi | 5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
index a02b984cc68d..1ae3fe828e59 100644
--- a/arch/arm/boot/dts/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8960.dtsi
@@ -73,11 +73,10 @@
cpu-offset = <0x80000>;
};
- msmgpio: gpio@800000 {
- compatible = "qcom,msm-gpio";
+ msmgpio: pinctrl@800000 {
+ compatible = "qcom,msm8960-pinctrl";
gpio-controller;
#gpio-cells = <2>;
- ngpio = <150>;
interrupts = <0 16 0x4>;
interrupt-controller;
#interrupt-cells = <2>;
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 11+ messages in thread* Re: [PATCH 1/5] ARM: dts: qcom: Replace gpio node with pinctrl node
2015-06-16 20:31 ` [PATCH 1/5] ARM: dts: qcom: Replace gpio node with pinctrl node Stephen Boyd
@ 2015-07-23 20:59 ` Andy Gross
0 siblings, 0 replies; 11+ messages in thread
From: Andy Gross @ 2015-07-23 20:59 UTC (permalink / raw)
To: Stephen Boyd; +Cc: linux-arm-msm, linux-kernel, linux-arm-kernel
On Tue, Jun 16, 2015 at 01:31:12PM -0700, Stephen Boyd wrote:
> Now that we have a proper pinctrl driver for the gpio block we
> can change the compatible field here and configure the pinmux on
> msm8960 devices.
>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> ---
Applied, thanks
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH 2/5] ARM: dts: qcom: Add MSM8960 RPM and RPM regulator nodes
2015-06-16 20:31 [PATCH 0/5] Enable SPI ethernet on MSM8960 CDP Stephen Boyd
2015-06-16 20:31 ` [PATCH 1/5] ARM: dts: qcom: Replace gpio node with pinctrl node Stephen Boyd
@ 2015-06-16 20:31 ` Stephen Boyd
2015-07-23 21:24 ` Andy Gross
2015-06-16 20:31 ` [PATCH 3/5] ARM: dts: qcom: Add MSM8960 CDP RPM regulators Stephen Boyd
` (2 subsequent siblings)
4 siblings, 1 reply; 11+ messages in thread
From: Stephen Boyd @ 2015-06-16 20:31 UTC (permalink / raw)
To: Andy Gross; +Cc: linux-kernel, linux-arm-msm, linux-arm-kernel
Add the basic RPM and RPM regulator nodes that boards can fill in
with their board specific details.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
arch/arm/boot/dts/qcom-msm8960.dtsi | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
index 1ae3fe828e59..fcf4bb5f9c3f 100644
--- a/arch/arm/boot/dts/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8960.dtsi
@@ -4,6 +4,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-msm8960.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
#include <dt-bindings/soc/qcom,gsbi.h>
/ {
@@ -104,6 +105,24 @@
#reset-cells = <1>;
};
+ l2cc: clock-controller@2011000 {
+ compatible = "syscon";
+ reg = <0x2011000 0x1000>;
+ };
+
+ rpm@108000 {
+ compatible = "qcom,rpm-msm8960";
+ reg = <0x108000 0x1000>;
+ qcom,ipc = <&l2cc 0x8 2>;
+
+ interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
+ interrupt-names = "ack", "err", "wakeup";
+
+ regulators {
+ compatible = "qcom,rpm-pm8921-regulators";
+ };
+ };
+
acc0: clock-controller@2088000 {
compatible = "qcom,kpss-acc-v1";
reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 11+ messages in thread* Re: [PATCH 2/5] ARM: dts: qcom: Add MSM8960 RPM and RPM regulator nodes
2015-06-16 20:31 ` [PATCH 2/5] ARM: dts: qcom: Add MSM8960 RPM and RPM regulator nodes Stephen Boyd
@ 2015-07-23 21:24 ` Andy Gross
0 siblings, 0 replies; 11+ messages in thread
From: Andy Gross @ 2015-07-23 21:24 UTC (permalink / raw)
To: Stephen Boyd; +Cc: linux-kernel, linux-arm-msm, linux-arm-kernel
On Tue, Jun 16, 2015 at 01:31:13PM -0700, Stephen Boyd wrote:
> Add the basic RPM and RPM regulator nodes that boards can fill in
> with their board specific details.
>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> ---
Applied, thanks
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH 3/5] ARM: dts: qcom: Add MSM8960 CDP RPM regulators
2015-06-16 20:31 [PATCH 0/5] Enable SPI ethernet on MSM8960 CDP Stephen Boyd
2015-06-16 20:31 ` [PATCH 1/5] ARM: dts: qcom: Replace gpio node with pinctrl node Stephen Boyd
2015-06-16 20:31 ` [PATCH 2/5] ARM: dts: qcom: Add MSM8960 RPM and RPM regulator nodes Stephen Boyd
@ 2015-06-16 20:31 ` Stephen Boyd
2015-07-23 21:04 ` Andy Gross
2015-06-16 20:31 ` [PATCH 4/5] ARM: dts: qcom: Add ks8851 node for wired ethernet Stephen Boyd
2015-06-16 20:31 ` [PATCH 5/5] ARM: qcom_defconfig: Enable options for KS8851 ethernet Stephen Boyd
4 siblings, 1 reply; 11+ messages in thread
From: Stephen Boyd @ 2015-06-16 20:31 UTC (permalink / raw)
To: Andy Gross; +Cc: linux-kernel, linux-arm-msm, linux-arm-kernel
Add RPM regulators and configure their constraints on the MSM8960
CDP so that we can control these supplies.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
arch/arm/boot/dts/qcom-msm8960-cdp.dts | 236 +++++++++++++++++++++++++++++++++
1 file changed, 236 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8960-cdp.dts b/arch/arm/boot/dts/qcom-msm8960-cdp.dts
index 7f70fae90959..be241f14246d 100644
--- a/arch/arm/boot/dts/qcom-msm8960-cdp.dts
+++ b/arch/arm/boot/dts/qcom-msm8960-cdp.dts
@@ -26,6 +26,242 @@
status = "okay";
};
};
+
+ rpm@108000 {
+ regulators {
+ compatible = "qcom,rpm-pm8921-regulators";
+ vin_lvs1_3_6-supply = <&pm8921_s4>;
+ vin_lvs2-supply = <&pm8921_s4>;
+ vin_lvs4_5_7-supply = <&pm8921_s4>;
+ vdd_ncp-supply = <&pm8921_l6>;
+ vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+ vdd_l21_l23_l29-supply = <&pm8921_s8>;
+ vdd_l24-supply = <&pm8921_s1>;
+ vdd_l25-supply = <&pm8921_s1>;
+ vdd_l27-supply = <&pm8921_s7>;
+ vdd_l28-supply = <&pm8921_s7>;
+
+ /* Buck SMPS */
+ pm8921_s1: s1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ };
+
+ pm8921_s2: s2 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+
+ pm8921_s3: s3 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1150000>;
+ qcom,switch-mode-frequency = <4800000>;
+ bias-pull-down;
+ };
+
+ pm8921_s4: s4 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+ };
+
+ pm8921_s7: s7 {
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ };
+
+ pm8921_s8: s8 {
+ regulator-always-on;
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+
+ /* PMOS LDO */
+ pm8921_l1: l1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ bias-pull-down;
+ };
+
+ pm8921_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+
+ pm8921_l3: l3 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ bias-pull-down;
+ };
+
+ pm8921_l4: l4 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ pm8921_l5: l5 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l6: l6 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l7: l7 {
+ regulator-always-on;
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l8: l8 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ };
+
+ pm8921_l9: l9 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ };
+
+ pm8921_l10: l10 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ };
+
+ pm8921_l11: l11 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+
+ pm8921_l12: l12 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+
+ pm8921_l14: l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ pm8921_l15: l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l16: l16 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ bias-pull-down;
+ };
+
+ pm8921_l17: l17 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l18: l18 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ bias-pull-down;
+ };
+
+ pm8921_l21: l21 {
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+ bias-pull-down;
+ };
+
+ pm8921_l22: l22 {
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <2750000>;
+ bias-pull-down;
+ };
+
+ pm8921_l23: l23 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ pm8921_l24: l24 {
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1150000>;
+ bias-pull-down;
+ };
+
+ pm8921_l25: l25 {
+ regulator-always-on;
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+ bias-pull-down;
+ };
+
+ /* Low Voltage Switch */
+ pm8921_lvs1: lvs1 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs2: lvs2 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs3: lvs3 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs4: lvs4 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs5: lvs5 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs6: lvs6 {
+ bias-pull-down;
+ };
+
+ pm8921_lvs7: lvs7 {
+ bias-pull-down;
+ };
+
+ pm8921_ncp: ncp {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ };
+ };
+ };
};
};
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 11+ messages in thread* Re: [PATCH 3/5] ARM: dts: qcom: Add MSM8960 CDP RPM regulators
2015-06-16 20:31 ` [PATCH 3/5] ARM: dts: qcom: Add MSM8960 CDP RPM regulators Stephen Boyd
@ 2015-07-23 21:04 ` Andy Gross
0 siblings, 0 replies; 11+ messages in thread
From: Andy Gross @ 2015-07-23 21:04 UTC (permalink / raw)
To: Stephen Boyd; +Cc: linux-kernel, linux-arm-msm, linux-arm-kernel
On Tue, Jun 16, 2015 at 01:31:14PM -0700, Stephen Boyd wrote:
> Add RPM regulators and configure their constraints on the MSM8960
> CDP so that we can control these supplies.
>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> ---
Applied, thanks
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH 4/5] ARM: dts: qcom: Add ks8851 node for wired ethernet
2015-06-16 20:31 [PATCH 0/5] Enable SPI ethernet on MSM8960 CDP Stephen Boyd
` (2 preceding siblings ...)
2015-06-16 20:31 ` [PATCH 3/5] ARM: dts: qcom: Add MSM8960 CDP RPM regulators Stephen Boyd
@ 2015-06-16 20:31 ` Stephen Boyd
2015-07-23 21:25 ` Andy Gross
2015-06-16 20:31 ` [PATCH 5/5] ARM: qcom_defconfig: Enable options for KS8851 ethernet Stephen Boyd
4 siblings, 1 reply; 11+ messages in thread
From: Stephen Boyd @ 2015-06-16 20:31 UTC (permalink / raw)
To: Andy Gross; +Cc: linux-arm-msm, linux-kernel, linux-arm-kernel
The micrel ks8851 device is present on MSM8960 CDP boards. It is
connected to two regulators, one controlled via a gpio and
another controlled via the RPM. Add the gsbi, spi, gpio
regulator, and micrel ks8851 nodes so that ethernet works
properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
arch/arm/boot/dts/qcom-msm8960-cdp.dts | 66 ++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/qcom-msm8960.dtsi | 25 +++++++++++++
2 files changed, 91 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8960-cdp.dts b/arch/arm/boot/dts/qcom-msm8960-cdp.dts
index be241f14246d..fad71d5527b0 100644
--- a/arch/arm/boot/dts/qcom-msm8960-cdp.dts
+++ b/arch/arm/boot/dts/qcom-msm8960-cdp.dts
@@ -262,6 +262,72 @@
};
};
};
+
+ gsbi@16000000 {
+ status = "ok";
+ qcom,mode = <GSBI_PROT_SPI>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_default>;
+ spi@16080000 {
+ status = "ok";
+ eth@0 {
+ compatible = "micrel,ks8851";
+ reg = <0>;
+ interrupt-parent = <&msmgpio>;
+ interrupts = <90 8>;
+ spi-max-frequency = <5400000>;
+ vdd-supply = <&ext_l2>;
+ vdd-io-supply = <&pm8921_lvs6>;
+ reset-gpios = <&msmgpio 89 0>;
+ };
+ };
+ };
+
+ pinctrl@800000 {
+ spi1_default: spi1_default {
+ mux {
+ pins = "gpio6", "gpio7", "gpio9";
+ function = "gsbi1";
+ };
+
+ mosi {
+ pins = "gpio6";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ miso {
+ pins = "gpio7";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs {
+ pins = "gpio8";
+ drive-strength = <12>;
+ bias-disable;
+ output-low;
+ };
+
+ clk {
+ pins = "gpio9";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+
+ ext_l2: gpio-regulator@91 {
+ compatible = "regulator-fixed";
+ regulator-name = "ext_l2";
+ gpio = <&msmgpio 91 0>;
+ startup-delay-us = <10000>;
+ enable-active-high;
+ };
};
};
diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
index fcf4bb5f9c3f..2096a94c9b52 100644
--- a/arch/arm/boot/dts/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8960.dtsi
@@ -271,5 +271,30 @@
compatible = "qcom,tcsr-msm8960", "syscon";
reg = <0x1a400000 0x100>;
};
+
+ gsbi@16000000 {
+ compatible = "qcom,gsbi-v1.0.0";
+ cell-index = <1>;
+ reg = <0x16000000 0x100>;
+ clocks = <&gcc GSBI1_H_CLK>;
+ clock-names = "iface";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ spi@16080000 {
+ compatible = "qcom,spi-qup-v1.1.1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x16080000 0x1000>;
+ interrupts = <0 147 0>;
+ spi-max-frequency = <24000000>;
+ cs-gpios = <&msmgpio 8 0>;
+
+ clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+ };
};
};
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 11+ messages in thread* Re: [PATCH 4/5] ARM: dts: qcom: Add ks8851 node for wired ethernet
2015-06-16 20:31 ` [PATCH 4/5] ARM: dts: qcom: Add ks8851 node for wired ethernet Stephen Boyd
@ 2015-07-23 21:25 ` Andy Gross
0 siblings, 0 replies; 11+ messages in thread
From: Andy Gross @ 2015-07-23 21:25 UTC (permalink / raw)
To: Stephen Boyd; +Cc: linux-kernel, linux-arm-msm, linux-arm-kernel
On Tue, Jun 16, 2015 at 01:31:15PM -0700, Stephen Boyd wrote:
> The micrel ks8851 device is present on MSM8960 CDP boards. It is
> connected to two regulators, one controlled via a gpio and
> another controlled via the RPM. Add the gsbi, spi, gpio
> regulator, and micrel ks8851 nodes so that ethernet works
> properly.
>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> ---
Applied, Thanks!
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH 5/5] ARM: qcom_defconfig: Enable options for KS8851 ethernet
2015-06-16 20:31 [PATCH 0/5] Enable SPI ethernet on MSM8960 CDP Stephen Boyd
` (3 preceding siblings ...)
2015-06-16 20:31 ` [PATCH 4/5] ARM: dts: qcom: Add ks8851 node for wired ethernet Stephen Boyd
@ 2015-06-16 20:31 ` Stephen Boyd
2015-07-23 21:02 ` Andy Gross
4 siblings, 1 reply; 11+ messages in thread
From: Stephen Boyd @ 2015-06-16 20:31 UTC (permalink / raw)
To: Andy Gross; +Cc: linux-kernel, linux-arm-msm, linux-arm-kernel
Enable the RPM and RPM regulator drivers as well as the KS8851
ethernet driver so that ethernet works on MSM8960 CDP.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
arch/arm/configs/qcom_defconfig | 3 +++
1 file changed, 3 insertions(+)
diff --git a/arch/arm/configs/qcom_defconfig b/arch/arm/configs/qcom_defconfig
index e6a6f282e3de..ff7985ba226e 100644
--- a/arch/arm/configs/qcom_defconfig
+++ b/arch/arm/configs/qcom_defconfig
@@ -67,6 +67,7 @@ CONFIG_SCSI_LOGGING=y
CONFIG_SCSI_SCAN_ASYNC=y
CONFIG_NETDEVICES=y
CONFIG_DUMMY=y
+CONFIG_KS8851=y
CONFIG_MDIO_BITBANG=y
CONFIG_MDIO_GPIO=y
CONFIG_SLIP=y
@@ -104,8 +105,10 @@ CONFIG_GPIO_SYSFS=y
CONFIG_POWER_RESET=y
CONFIG_POWER_RESET_MSM=y
CONFIG_THERMAL=y
+CONFIG_MFD_QCOM_RPM=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_QCOM_RPM=y
CONFIG_MEDIA_SUPPORT=y
CONFIG_FB=y
CONFIG_SOUND=y
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 11+ messages in thread* Re: [PATCH 5/5] ARM: qcom_defconfig: Enable options for KS8851 ethernet
2015-06-16 20:31 ` [PATCH 5/5] ARM: qcom_defconfig: Enable options for KS8851 ethernet Stephen Boyd
@ 2015-07-23 21:02 ` Andy Gross
0 siblings, 0 replies; 11+ messages in thread
From: Andy Gross @ 2015-07-23 21:02 UTC (permalink / raw)
To: Stephen Boyd; +Cc: linux-kernel, linux-arm-msm, linux-arm-kernel
On Tue, Jun 16, 2015 at 01:31:16PM -0700, Stephen Boyd wrote:
> Enable the RPM and RPM regulator drivers as well as the KS8851
> ethernet driver so that ethernet works on MSM8960 CDP.
>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> ---
Applied, thanks!
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 11+ messages in thread