From: Rajendra Nayak <rnayak@codeaurora.org>
To: viresh.kumar@linaro.org, sboyd@kernel.org, andy.gross@linaro.org,
ulf.hansson@linaro.org
Cc: devicetree@vger.kernel.org, linux-arm-msm@vger.kernel.org,
linux-kernel@vger.kernel.org, collinsd@codeaurora.org,
Rajendra Nayak <rnayak@codeaurora.org>
Subject: [PATCH v2 2/6] dt-bindings: opp: Introduce qcom-opp bindings
Date: Fri, 25 May 2018 15:31:17 +0530 [thread overview]
Message-ID: <20180525100121.28214-3-rnayak@codeaurora.org> (raw)
In-Reply-To: <20180525100121.28214-1-rnayak@codeaurora.org>
On Qualcomm platforms, an OPP node needs to describe an
additional level/corner value that is then communicated to
a remote microprocessor by the CPU, which then takes some
actions (like adjusting voltage values across various rails)
based on the value passed.
Describe these bindings in the qcom-opp bindings document.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/opp/qcom-opp.txt | 25 +++++++++++++++++++
1 file changed, 25 insertions(+)
create mode 100644 Documentation/devicetree/bindings/opp/qcom-opp.txt
diff --git a/Documentation/devicetree/bindings/opp/qcom-opp.txt b/Documentation/devicetree/bindings/opp/qcom-opp.txt
new file mode 100644
index 000000000000..db4d970c7ec7
--- /dev/null
+++ b/Documentation/devicetree/bindings/opp/qcom-opp.txt
@@ -0,0 +1,25 @@
+Qualcomm OPP bindings to descibe OPP nodes with corner/level values
+
+OPP tables for devices on Qualcomm platforms require an additional
+platform specific corner/level value to be specified.
+This value is passed on to the RPM (Resource Power Manager) by
+the CPU, which then takes the necessary actions to set a voltage
+rail to an appropriate voltage based on the value passed.
+
+The bindings are based on top of the operating-points-v2 bindings
+described in Documentation/devicetree/bindings/opp/opp.txt
+Additional properties are described below.
+
+* OPP Table Node
+
+Required properties:
+- compatible: Allow OPPs to express their compatibility. It should be:
+ "operating-points-v2-qcom-level"
+
+* OPP Node
+
+Required properties:
+- qcom,level: On Qualcomm platforms an OPP node can describe a positive value
+representing a corner/level that's communicated with a remote microprocessor
+(usually called the RPM) which then translates it into a certain voltage on
+a voltage rail.
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2018-05-25 10:01 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-25 10:01 [PATCH v2 0/6] Add powerdomain driver for corners on msm8996/sdm845 Rajendra Nayak
2018-05-25 10:01 ` [PATCH v2 1/6] soc: qcom: rpmpd: Add a powerdomain driver to model corners Rajendra Nayak
2018-05-30 9:17 ` Ulf Hansson
2018-05-30 10:14 ` Rajendra Nayak
2018-05-30 12:44 ` Ulf Hansson
2018-05-31 4:20 ` Rajendra Nayak
2018-05-31 11:09 ` Ulf Hansson
2018-05-30 18:27 ` David Collins
2018-05-31 3:53 ` Rajendra Nayak
2018-05-31 3:27 ` Rob Herring
2018-05-31 4:14 ` Rajendra Nayak
2018-05-25 10:01 ` Rajendra Nayak [this message]
2018-05-25 22:33 ` [PATCH v2 2/6] dt-bindings: opp: Introduce qcom-opp bindings David Collins
2018-05-29 9:49 ` Rajendra Nayak
2018-05-25 10:01 ` [PATCH v2 3/6] soc: qcom: rpmpd: Add support for get/set performance state Rajendra Nayak
2018-05-25 10:01 ` [PATCH v2 4/6] arm64: dts: msm8996: Add rpmpd device node Rajendra Nayak
2018-05-25 10:01 ` [PATCH v2 5/6] soc: qcom: rpmh powerdomain driver Rajendra Nayak
2018-05-26 1:08 ` David Collins
2018-05-29 10:19 ` Rajendra Nayak
2018-05-29 19:03 ` David Collins
2018-05-30 8:55 ` Rajendra Nayak
2018-05-30 9:44 ` Viresh Kumar
2018-05-30 10:07 ` Rajendra Nayak
2018-06-01 8:48 ` Rajendra Nayak
2018-06-01 19:19 ` David Collins
2018-06-13 18:29 ` Lina Iyer
2018-05-31 3:31 ` Rob Herring
2018-05-31 4:15 ` Rajendra Nayak
2018-05-25 10:01 ` [PATCH v2 6/6] soc: qcom: rpmpd/rpmhpd: Add a max vote on all corners at init Rajendra Nayak
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180525100121.28214-3-rnayak@codeaurora.org \
--to=rnayak@codeaurora.org \
--cc=andy.gross@linaro.org \
--cc=collinsd@codeaurora.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=sboyd@kernel.org \
--cc=ulf.hansson@linaro.org \
--cc=viresh.kumar@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).