* [PATCH 1/2] arm64: dts: qcom: sdm845: Add I2C, SPI, and UART9 nodes
@ 2018-06-07 20:46 Douglas Anderson
2018-06-07 20:46 ` [PATCH 2/2] arm64: dts: qcom: sdm845: Enable debug UART and I2C10 on sdm845-mtp Douglas Anderson
2018-06-12 5:01 ` [PATCH 1/2] arm64: dts: qcom: sdm845: Add I2C, SPI, and UART9 nodes Bjorn Andersson
0 siblings, 2 replies; 5+ messages in thread
From: Douglas Anderson @ 2018-06-07 20:46 UTC (permalink / raw)
To: andy.gross
Cc: rnayak, bjorn.andersson, kramasub, sdharia, swboyd,
Douglas Anderson, devicetree, linux-arm-msm, linux-kernel,
Rob Herring, David Brown, Will Deacon, Mark Rutland, linux-soc,
Catalin Marinas, linux-arm-kernel
This adds nodes to SDM845-dtsi for all the I2C ports, all the SPI
ports, and UART9. Note that I2C / SPI / UART are a bit strange on
sdm845 because each "serial engine" has 4 pins associated with it and
depending on which firmware has been loaded into the serial engine
(loaded by the BIOS) the serial engine can behave like an I2C port, a
SPI port, or a UART. As per the landed bindings that means that we
need to create one node for each possible mode that the port could be
in. With 16 serial engines that means 16 x 3 = 48 nodes.
We get away with only creating 33 nodes for now because it seems very
likely that SDM845-based boards will actually all use the same UART
(UART 9) for debug purposes. While another UART could be used for
something like Bluetooth communication we can cross that path when we
come to it. Some documentation that I saw implied that using a UART
for "high speed" communications actually needs yet another different
serial engine firmware anyway.
Note that quick measurements adding all these nodes adds ~10k of extra
space per dtb that they're included with. If this becomes a problem
we may need to think of a different way to structure this so that
boards only get the nodes they need (or figure out how to get dtc to
strip 'disabled' nodes). For now it seems OK.
These nodes were programmatically generated with a fairly dumb python
script. See http://crosreview.com/1091631 for the source.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
---
arch/arm64/boot/dts/qcom/sdm845.dtsi | 1013 ++++++++++++++++++++++++++
1 file changed, 1013 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index cdaabeb3c995..2dc5c7dcc9aa 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -5,6 +5,7 @@
* Copyright (c) 2018, The Linux Foundation. All rights reserved.
*/
+#include <dt-bindings/clock/qcom,gcc-sdm845.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
@@ -13,6 +14,41 @@
#address-cells = <2>;
#size-cells = <2>;
+ aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ i2c3 = &i2c3;
+ i2c4 = &i2c4;
+ i2c5 = &i2c5;
+ i2c6 = &i2c6;
+ i2c7 = &i2c7;
+ i2c8 = &i2c8;
+ i2c9 = &i2c9;
+ i2c10 = &i2c10;
+ i2c11 = &i2c11;
+ i2c12 = &i2c12;
+ i2c13 = &i2c13;
+ i2c14 = &i2c14;
+ i2c15 = &i2c15;
+ spi0 = &spi0;
+ spi1 = &spi1;
+ spi2 = &spi2;
+ spi3 = &spi3;
+ spi4 = &spi4;
+ spi5 = &spi5;
+ spi6 = &spi6;
+ spi7 = &spi7;
+ spi8 = &spi8;
+ spi9 = &spi9;
+ spi10 = &spi10;
+ spi11 = &spi11;
+ spi12 = &spi12;
+ spi13 = &spi13;
+ spi14 = &spi14;
+ spi15 = &spi15;
+ };
+
chosen { };
memory@80000000 {
@@ -206,6 +242,489 @@
#power-domain-cells = <1>;
};
+ qupv3_id_0: geniqup@8c0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0x8c0000 0x6000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ i2c0: i2c@880000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x880000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c0_default>;
+ pinctrl-1 = <&qup_i2c0_sleep>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi0: spi@880000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x880000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi0_default>;
+ pinctrl-1 = <&qup_spi0_sleep>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@884000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x884000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c1_default>;
+ pinctrl-1 = <&qup_i2c1_sleep>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi1: spi@884000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x884000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi1_default>;
+ pinctrl-1 = <&qup_spi1_sleep>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@888000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x888000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c2_default>;
+ pinctrl-1 = <&qup_i2c2_sleep>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi2: spi@888000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x888000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi2_default>;
+ pinctrl-1 = <&qup_spi2_sleep>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@88c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x88c000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c3_default>;
+ pinctrl-1 = <&qup_i2c3_sleep>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi3: spi@88c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x88c000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi3_default>;
+ pinctrl-1 = <&qup_spi3_sleep>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@890000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x890000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c4_default>;
+ pinctrl-1 = <&qup_i2c4_sleep>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi4: spi@890000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x890000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi4_default>;
+ pinctrl-1 = <&qup_spi4_sleep>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c5: i2c@894000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x894000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c5_default>;
+ pinctrl-1 = <&qup_i2c5_sleep>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi5: spi@894000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x894000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi5_default>;
+ pinctrl-1 = <&qup_spi5_sleep>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c6: i2c@898000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x898000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c6_default>;
+ pinctrl-1 = <&qup_i2c6_sleep>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi6: spi@898000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x898000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi6_default>;
+ pinctrl-1 = <&qup_spi6_sleep>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c7: i2c@89c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x89c000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c7_default>;
+ pinctrl-1 = <&qup_i2c7_sleep>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi7: spi@89c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x89c000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi7_default>;
+ pinctrl-1 = <&qup_spi7_sleep>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+ };
+
+ qupv3_id_1: geniqup@ac0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0xac0000 0x6000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ status = "disabled";
+
+ i2c8: i2c@a80000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0xa80000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c8_default>;
+ pinctrl-1 = <&qup_i2c8_sleep>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi8: spi@a80000 {
+ compatible = "qcom,geni-spi";
+ reg = <0xa80000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi8_default>;
+ pinctrl-1 = <&qup_spi8_sleep>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c9: i2c@a84000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0xa84000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c9_default>;
+ pinctrl-1 = <&qup_i2c9_sleep>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi9: spi@a84000 {
+ compatible = "qcom,geni-spi";
+ reg = <0xa84000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi9_default>;
+ pinctrl-1 = <&qup_spi9_sleep>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart9: serial@a84000 {
+ compatible = "qcom,geni-debug-uart";
+ reg = <0xa84000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_uart9_default>;
+ pinctrl-1 = <&qup_uart9_sleep>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ i2c10: i2c@a88000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0xa88000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c10_default>;
+ pinctrl-1 = <&qup_i2c10_sleep>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi10: spi@a88000 {
+ compatible = "qcom,geni-spi";
+ reg = <0xa88000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi10_default>;
+ pinctrl-1 = <&qup_spi10_sleep>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c11: i2c@a8c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0xa8c000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c11_default>;
+ pinctrl-1 = <&qup_i2c11_sleep>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi11: spi@a8c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0xa8c000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi11_default>;
+ pinctrl-1 = <&qup_spi11_sleep>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c12: i2c@a90000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0xa90000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c12_default>;
+ pinctrl-1 = <&qup_i2c12_sleep>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi12: spi@a90000 {
+ compatible = "qcom,geni-spi";
+ reg = <0xa90000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi12_default>;
+ pinctrl-1 = <&qup_spi12_sleep>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c13: i2c@a94000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0xa94000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c13_default>;
+ pinctrl-1 = <&qup_i2c13_sleep>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi13: spi@a94000 {
+ compatible = "qcom,geni-spi";
+ reg = <0xa94000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi13_default>;
+ pinctrl-1 = <&qup_spi13_sleep>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c14: i2c@a98000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0xa98000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c14_default>;
+ pinctrl-1 = <&qup_i2c14_sleep>;
+ interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi14: spi@a98000 {
+ compatible = "qcom,geni-spi";
+ reg = <0xa98000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi14_default>;
+ pinctrl-1 = <&qup_spi14_sleep>;
+ interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c15: i2c@a9c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0xa9c000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_i2c15_default>;
+ pinctrl-1 = <&qup_i2c15_sleep>;
+ interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi15: spi@a9c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0xa9c000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_spi15_default>;
+ pinctrl-1 = <&qup_spi15_sleep>;
+ interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+ };
+
tcsr_mutex_regs: syscon@1f40000 {
compatible = "syscon";
reg = <0x1f40000 0x40000>;
@@ -219,6 +738,500 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+
+ qup_i2c0_default: qup-i2c0-default {
+ pinmux {
+ pins = "gpio0", "gpio1";
+ function = "qup0";
+ };
+ };
+
+ qup_i2c0_sleep: qup-i2c0-sleep {
+ pinmux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ };
+ };
+
+ qup_i2c1_default: qup-i2c1-default {
+ pinmux {
+ pins = "gpio17", "gpio18";
+ function = "qup1";
+ };
+ };
+
+ qup_i2c1_sleep: qup-i2c1-sleep {
+ pinmux {
+ pins = "gpio17", "gpio18";
+ function = "gpio";
+ };
+ };
+
+ qup_i2c2_default: qup-i2c2-default {
+ pinmux {
+ pins = "gpio27", "gpio28";
+ function = "qup2";
+ };
+ };
+
+ qup_i2c2_sleep: qup-i2c2-sleep {
+ pinmux {
+ pins = "gpio27", "gpio28";
+ function = "gpio";
+ };
+ };
+
+ qup_i2c3_default: qup-i2c3-default {
+ pinmux {
+ pins = "gpio41", "gpio42";
+ function = "qup3";
+ };
+ };
+
+ qup_i2c3_sleep: qup-i2c3-sleep {
+ pinmux {
+ pins = "gpio41", "gpio42";
+ function = "gpio";
+ };
+ };
+
+ qup_i2c4_default: qup-i2c4-default {
+ pinmux {
+ pins = "gpio89", "gpio90";
+ function = "qup4";
+ };
+ };
+
+ qup_i2c4_sleep: qup-i2c4-sleep {
+ pinmux {
+ pins = "gpio89", "gpio90";
+ function = "gpio";
+ };
+ };
+
+ qup_i2c5_default: qup-i2c5-default {
+ pinmux {
+ pins = "gpio85", "gpio86";
+ function = "qup5";
+ };
+ };
+
+ qup_i2c5_sleep: qup-i2c5-sleep {
+ pinmux {
+ pins = "gpio85", "gpio86";
+ function = "gpio";
+ };
+ };
+
+ qup_i2c6_default: qup-i2c6-default {
+ pinmux {
+ pins = "gpio45", "gpio46";
+ function = "qup6";
+ };
+ };
+
+ qup_i2c6_sleep: qup-i2c6-sleep {
+ pinmux {
+ pins = "gpio45", "gpio46";
+ function = "gpio";
+ };
+ };
+
+ qup_i2c7_default: qup-i2c7-default {
+ pinmux {
+ pins = "gpio93", "gpio94";
+ function = "qup7";
+ };
+ };
+
+ qup_i2c7_sleep: qup-i2c7-sleep {
+ pinmux {
+ pins = "gpio93", "gpio94";
+ function = "gpio";
+ };
+ };
+
+ qup_i2c8_default: qup-i2c8-default {
+ pinmux {
+ pins = "gpio65", "gpio66";
+ function = "qup8";
+ };
+ };
+
+ qup_i2c8_sleep: qup-i2c8-sleep {
+ pinmux {
+ pins = "gpio65", "gpio66";
+ function = "gpio";
+ };
+ };
+
+ qup_i2c9_default: qup-i2c9-default {
+ pinmux {
+ pins = "gpio6", "gpio7";
+ function = "qup9";
+ };
+ };
+
+ qup_i2c9_sleep: qup-i2c9-sleep {
+ pinmux {
+ pins = "gpio6", "gpio7";
+ function = "gpio";
+ };
+ };
+
+ qup_i2c10_default: qup-i2c10-default {
+ pinmux {
+ pins = "gpio55", "gpio56";
+ function = "qup10";
+ };
+ };
+
+ qup_i2c10_sleep: qup-i2c10-sleep {
+ pinmux {
+ pins = "gpio55", "gpio56";
+ function = "gpio";
+ };
+ };
+
+ qup_i2c11_default: qup-i2c11-default {
+ pinmux {
+ pins = "gpio31", "gpio32";
+ function = "qup11";
+ };
+ };
+
+ qup_i2c11_sleep: qup-i2c11-sleep {
+ pinmux {
+ pins = "gpio31", "gpio32";
+ function = "gpio";
+ };
+ };
+
+ qup_i2c12_default: qup-i2c12-default {
+ pinmux {
+ pins = "gpio49", "gpio50";
+ function = "qup12";
+ };
+ };
+
+ qup_i2c12_sleep: qup-i2c12-sleep {
+ pinmux {
+ pins = "gpio49", "gpio50";
+ function = "gpio";
+ };
+ };
+
+ qup_i2c13_default: qup-i2c13-default {
+ pinmux {
+ pins = "gpio105", "gpio106";
+ function = "qup13";
+ };
+ };
+
+ qup_i2c13_sleep: qup-i2c13-sleep {
+ pinmux {
+ pins = "gpio105", "gpio106";
+ function = "gpio";
+ };
+ };
+
+ qup_i2c14_default: qup-i2c14-default {
+ pinmux {
+ pins = "gpio33", "gpio34";
+ function = "qup14";
+ };
+ };
+
+ qup_i2c14_sleep: qup-i2c14-sleep {
+ pinmux {
+ pins = "gpio33", "gpio34";
+ function = "gpio";
+ };
+ };
+
+ qup_i2c15_default: qup-i2c15-default {
+ pinmux {
+ pins = "gpio81", "gpio82";
+ function = "qup15";
+ };
+ };
+
+ qup_i2c15_sleep: qup-i2c15-sleep {
+ pinmux {
+ pins = "gpio81", "gpio82";
+ function = "gpio";
+ };
+ };
+
+ qup_spi0_default: qup-spi0-default {
+ pinmux {
+ pins = "gpio0", "gpio1",
+ "gpio2", "gpio3";
+ function = "qup0";
+ };
+ };
+
+ qup_spi0_sleep: qup-spi0-sleep {
+ pinmux {
+ pins = "gpio0", "gpio1",
+ "gpio2", "gpio3";
+ function = "gpio";
+ };
+ };
+
+ qup_spi1_default: qup-spi1-default {
+ pinmux {
+ pins = "gpio17", "gpio18",
+ "gpio19", "gpio20";
+ function = "qup1";
+ };
+ };
+
+ qup_spi1_sleep: qup-spi1-sleep {
+ pinmux {
+ pins = "gpio17", "gpio18",
+ "gpio19", "gpio20";
+ function = "gpio";
+ };
+ };
+
+ qup_spi2_default: qup-spi2-default {
+ pinmux {
+ pins = "gpio27", "gpio28",
+ "gpio29", "gpio30";
+ function = "qup2";
+ };
+ };
+
+ qup_spi2_sleep: qup-spi2-sleep {
+ pinmux {
+ pins = "gpio27", "gpio28",
+ "gpio29", "gpio30";
+ function = "gpio";
+ };
+ };
+
+ qup_spi3_default: qup-spi3-default {
+ pinmux {
+ pins = "gpio41", "gpio42",
+ "gpio43", "gpio44";
+ function = "qup3";
+ };
+ };
+
+ qup_spi3_sleep: qup-spi3-sleep {
+ pinmux {
+ pins = "gpio41", "gpio42",
+ "gpio43", "gpio44";
+ function = "gpio";
+ };
+ };
+
+ qup_spi4_default: qup-spi4-default {
+ pinmux {
+ pins = "gpio89", "gpio90",
+ "gpio91", "gpio92";
+ function = "qup4";
+ };
+ };
+
+ qup_spi4_sleep: qup-spi4-sleep {
+ pinmux {
+ pins = "gpio89", "gpio90",
+ "gpio91", "gpio92";
+ function = "gpio";
+ };
+ };
+
+ qup_spi5_default: qup-spi5-default {
+ pinmux {
+ pins = "gpio85", "gpio86",
+ "gpio87", "gpio88";
+ function = "qup5";
+ };
+ };
+
+ qup_spi5_sleep: qup-spi5-sleep {
+ pinmux {
+ pins = "gpio85", "gpio86",
+ "gpio87", "gpio88";
+ function = "gpio";
+ };
+ };
+
+ qup_spi6_default: qup-spi6-default {
+ pinmux {
+ pins = "gpio45", "gpio46",
+ "gpio47", "gpio48";
+ function = "qup6";
+ };
+ };
+
+ qup_spi6_sleep: qup-spi6-sleep {
+ pinmux {
+ pins = "gpio45", "gpio46",
+ "gpio47", "gpio48";
+ function = "gpio";
+ };
+ };
+
+ qup_spi7_default: qup-spi7-default {
+ pinmux {
+ pins = "gpio93", "gpio94",
+ "gpio95", "gpio96";
+ function = "qup7";
+ };
+ };
+
+ qup_spi7_sleep: qup-spi7-sleep {
+ pinmux {
+ pins = "gpio93", "gpio94",
+ "gpio95", "gpio96";
+ function = "gpio";
+ };
+ };
+
+ qup_spi8_default: qup-spi8-default {
+ pinmux {
+ pins = "gpio65", "gpio66",
+ "gpio67", "gpio68";
+ function = "qup8";
+ };
+ };
+
+ qup_spi8_sleep: qup-spi8-sleep {
+ pinmux {
+ pins = "gpio65", "gpio66",
+ "gpio67", "gpio68";
+ function = "gpio";
+ };
+ };
+
+ qup_spi9_default: qup-spi9-default {
+ pinmux {
+ pins = "gpio6", "gpio7",
+ "gpio4", "gpio5";
+ function = "qup9";
+ };
+ };
+
+ qup_spi9_sleep: qup-spi9-sleep {
+ pinmux {
+ pins = "gpio6", "gpio7",
+ "gpio4", "gpio5";
+ function = "gpio";
+ };
+ };
+
+ qup_spi10_default: qup-spi10-default {
+ pinmux {
+ pins = "gpio55", "gpio56",
+ "gpio53", "gpio54";
+ function = "qup10";
+ };
+ };
+
+ qup_spi10_sleep: qup-spi10-sleep {
+ pinmux {
+ pins = "gpio55", "gpio56",
+ "gpio53", "gpio54";
+ function = "gpio";
+ };
+ };
+
+ qup_spi11_default: qup-spi11-default {
+ pinmux {
+ pins = "gpio31", "gpio32",
+ "gpio33", "gpio34";
+ function = "qup11";
+ };
+ };
+
+ qup_spi11_sleep: qup-spi11-sleep {
+ pinmux {
+ pins = "gpio31", "gpio32",
+ "gpio33", "gpio34";
+ function = "gpio";
+ };
+ };
+
+ qup_spi12_default: qup-spi12-default {
+ pinmux {
+ pins = "gpio49", "gpio50",
+ "gpio51", "gpio52";
+ function = "qup12";
+ };
+ };
+
+ qup_spi12_sleep: qup-spi12-sleep {
+ pinmux {
+ pins = "gpio49", "gpio50",
+ "gpio51", "gpio52";
+ function = "gpio";
+ };
+ };
+
+ qup_spi13_default: qup-spi13-default {
+ pinmux {
+ pins = "gpio105", "gpio106",
+ "gpio107", "gpio108";
+ function = "qup13";
+ };
+ };
+
+ qup_spi13_sleep: qup-spi13-sleep {
+ pinmux {
+ pins = "gpio105", "gpio106",
+ "gpio107", "gpio108";
+ function = "gpio";
+ };
+ };
+
+ qup_spi14_default: qup-spi14-default {
+ pinmux {
+ pins = "gpio33", "gpio34",
+ "gpio31", "gpio32";
+ function = "qup14";
+ };
+ };
+
+ qup_spi14_sleep: qup-spi14-sleep {
+ pinmux {
+ pins = "gpio33", "gpio34",
+ "gpio31", "gpio32";
+ function = "gpio";
+ };
+ };
+
+ qup_spi15_default: qup-spi15-default {
+ pinmux {
+ pins = "gpio81", "gpio82",
+ "gpio83", "gpio84";
+ function = "qup15";
+ };
+ };
+
+ qup_spi15_sleep: qup-spi15-sleep {
+ pinmux {
+ pins = "gpio81", "gpio82",
+ "gpio83", "gpio84";
+ function = "gpio";
+ };
+ };
+
+ qup_uart9_default: qup-uart9-default {
+ pinmux {
+ pins = "gpio4", "gpio5";
+ function = "qup9";
+ };
+ };
+
+ qup_uart9_sleep: qup-uart9-sleep {
+ pinmux {
+ pins = "gpio4", "gpio5";
+ function = "gpio";
+ };
+ };
};
spmi_bus: spmi@c440000 {
--
2.17.1.1185.g55be947832-goog
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 2/2] arm64: dts: qcom: sdm845: Enable debug UART and I2C10 on sdm845-mtp
2018-06-07 20:46 [PATCH 1/2] arm64: dts: qcom: sdm845: Add I2C, SPI, and UART9 nodes Douglas Anderson
@ 2018-06-07 20:46 ` Douglas Anderson
2018-06-12 5:01 ` Bjorn Andersson
2018-06-12 5:01 ` [PATCH 1/2] arm64: dts: qcom: sdm845: Add I2C, SPI, and UART9 nodes Bjorn Andersson
1 sibling, 1 reply; 5+ messages in thread
From: Douglas Anderson @ 2018-06-07 20:46 UTC (permalink / raw)
To: andy.gross
Cc: Mark Rutland, devicetree, rnayak, linux-arm-msm, Will Deacon,
Douglas Anderson, swboyd, David Brown, Rob Herring, kramasub,
linux-arm-kernel, Catalin Marinas, bjorn.andersson, linux-soc,
sdharia, linux-kernel
The debug UART is very useful to have. I2C10 is enabled as an example
of a I2C port we can talk on for now. Eventually we'll want to put
peripherals under it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
---
arch/arm64/boot/dts/qcom/sdm845-mtp.dts | 52 +++++++++++++++++++++++++
1 file changed, 52 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
index 979ab49913f1..e1eda143a725 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
@@ -12,4 +12,56 @@
/ {
model = "Qualcomm Technologies, Inc. SDM845 MTP";
compatible = "qcom,sdm845-mtp";
+
+ aliases {
+ serial0 = &uart9;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&i2c10 {
+ status = "okay";
+ clock-frequency = <400000>;
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&uart9 {
+ status = "okay";
+};
+
+/* PINCTRL - additions to nodes defined in sdm845.dtsi */
+
+&qup_i2c10_default {
+ pinconf {
+ pins = "gpio55", "gpio56";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&qup_uart9_default {
+ pinconf-tx {
+ pins = "gpio4";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pinconf-rx {
+ pins = "gpio5";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+};
+
+&qup_uart9_sleep {
+ pinconf {
+ pins = "gpio4", "gpio5";
+ bias-pull-down;
+ };
};
--
2.17.1.1185.g55be947832-goog
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH 1/2] arm64: dts: qcom: sdm845: Add I2C, SPI, and UART9 nodes
2018-06-07 20:46 [PATCH 1/2] arm64: dts: qcom: sdm845: Add I2C, SPI, and UART9 nodes Douglas Anderson
2018-06-07 20:46 ` [PATCH 2/2] arm64: dts: qcom: sdm845: Enable debug UART and I2C10 on sdm845-mtp Douglas Anderson
@ 2018-06-12 5:01 ` Bjorn Andersson
2018-06-12 5:22 ` Doug Anderson
1 sibling, 1 reply; 5+ messages in thread
From: Bjorn Andersson @ 2018-06-12 5:01 UTC (permalink / raw)
To: Douglas Anderson
Cc: andy.gross, rnayak, kramasub, sdharia, swboyd, devicetree,
linux-arm-msm, linux-kernel, Rob Herring, David Brown,
Will Deacon, Mark Rutland, linux-soc, Catalin Marinas,
linux-arm-kernel
On Thu 07 Jun 13:46 PDT 2018, Douglas Anderson wrote:
> This adds nodes to SDM845-dtsi for all the I2C ports, all the SPI
> ports, and UART9. Note that I2C / SPI / UART are a bit strange on
> sdm845 because each "serial engine" has 4 pins associated with it and
> depending on which firmware has been loaded into the serial engine
> (loaded by the BIOS) the serial engine can behave like an I2C port, a
> SPI port, or a UART. As per the landed bindings that means that we
> need to create one node for each possible mode that the port could be
> in. With 16 serial engines that means 16 x 3 = 48 nodes.
>
> We get away with only creating 33 nodes for now because it seems very
> likely that SDM845-based boards will actually all use the same UART
> (UART 9) for debug purposes. While another UART could be used for
> something like Bluetooth communication we can cross that path when we
> come to it. Some documentation that I saw implied that using a UART
> for "high speed" communications actually needs yet another different
> serial engine firmware anyway.
>
> Note that quick measurements adding all these nodes adds ~10k of extra
> space per dtb that they're included with. If this becomes a problem
> we may need to think of a different way to structure this so that
> boards only get the nodes they need (or figure out how to get dtc to
> strip 'disabled' nodes). For now it seems OK.
>
> These nodes were programmatically generated with a fairly dumb python
> script. See http://crosreview.com/1091631 for the source.
>
> Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Regards,
Bjorn
> ---
>
> arch/arm64/boot/dts/qcom/sdm845.dtsi | 1013 ++++++++++++++++++++++++++
> 1 file changed, 1013 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> index cdaabeb3c995..2dc5c7dcc9aa 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> @@ -5,6 +5,7 @@
> * Copyright (c) 2018, The Linux Foundation. All rights reserved.
> */
>
> +#include <dt-bindings/clock/qcom,gcc-sdm845.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
>
> / {
> @@ -13,6 +14,41 @@
> #address-cells = <2>;
> #size-cells = <2>;
>
> + aliases {
> + i2c0 = &i2c0;
> + i2c1 = &i2c1;
> + i2c2 = &i2c2;
> + i2c3 = &i2c3;
> + i2c4 = &i2c4;
> + i2c5 = &i2c5;
> + i2c6 = &i2c6;
> + i2c7 = &i2c7;
> + i2c8 = &i2c8;
> + i2c9 = &i2c9;
> + i2c10 = &i2c10;
> + i2c11 = &i2c11;
> + i2c12 = &i2c12;
> + i2c13 = &i2c13;
> + i2c14 = &i2c14;
> + i2c15 = &i2c15;
> + spi0 = &spi0;
> + spi1 = &spi1;
> + spi2 = &spi2;
> + spi3 = &spi3;
> + spi4 = &spi4;
> + spi5 = &spi5;
> + spi6 = &spi6;
> + spi7 = &spi7;
> + spi8 = &spi8;
> + spi9 = &spi9;
> + spi10 = &spi10;
> + spi11 = &spi11;
> + spi12 = &spi12;
> + spi13 = &spi13;
> + spi14 = &spi14;
> + spi15 = &spi15;
> + };
> +
> chosen { };
>
> memory@80000000 {
> @@ -206,6 +242,489 @@
> #power-domain-cells = <1>;
> };
>
> + qupv3_id_0: geniqup@8c0000 {
> + compatible = "qcom,geni-se-qup";
> + reg = <0x8c0000 0x6000>;
> + clock-names = "m-ahb", "s-ahb";
> + clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
> + <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + i2c0: i2c@880000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x880000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c0_default>;
> + pinctrl-1 = <&qup_i2c0_sleep>;
> + interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi0: spi@880000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x880000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi0_default>;
> + pinctrl-1 = <&qup_spi0_sleep>;
> + interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c1: i2c@884000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x884000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c1_default>;
> + pinctrl-1 = <&qup_i2c1_sleep>;
> + interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi1: spi@884000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x884000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi1_default>;
> + pinctrl-1 = <&qup_spi1_sleep>;
> + interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c2: i2c@888000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x888000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c2_default>;
> + pinctrl-1 = <&qup_i2c2_sleep>;
> + interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi2: spi@888000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x888000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi2_default>;
> + pinctrl-1 = <&qup_spi2_sleep>;
> + interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c3: i2c@88c000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x88c000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c3_default>;
> + pinctrl-1 = <&qup_i2c3_sleep>;
> + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi3: spi@88c000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x88c000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi3_default>;
> + pinctrl-1 = <&qup_spi3_sleep>;
> + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c4: i2c@890000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x890000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c4_default>;
> + pinctrl-1 = <&qup_i2c4_sleep>;
> + interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi4: spi@890000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x890000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi4_default>;
> + pinctrl-1 = <&qup_spi4_sleep>;
> + interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c5: i2c@894000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x894000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c5_default>;
> + pinctrl-1 = <&qup_i2c5_sleep>;
> + interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi5: spi@894000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x894000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi5_default>;
> + pinctrl-1 = <&qup_spi5_sleep>;
> + interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c6: i2c@898000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x898000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c6_default>;
> + pinctrl-1 = <&qup_i2c6_sleep>;
> + interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi6: spi@898000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x898000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi6_default>;
> + pinctrl-1 = <&qup_spi6_sleep>;
> + interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c7: i2c@89c000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x89c000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c7_default>;
> + pinctrl-1 = <&qup_i2c7_sleep>;
> + interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi7: spi@89c000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x89c000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi7_default>;
> + pinctrl-1 = <&qup_spi7_sleep>;
> + interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> + };
> +
> + qupv3_id_1: geniqup@ac0000 {
> + compatible = "qcom,geni-se-qup";
> + reg = <0xac0000 0x6000>;
> + clock-names = "m-ahb", "s-ahb";
> + clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
> + <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> + status = "disabled";
> +
> + i2c8: i2c@a80000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0xa80000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c8_default>;
> + pinctrl-1 = <&qup_i2c8_sleep>;
> + interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi8: spi@a80000 {
> + compatible = "qcom,geni-spi";
> + reg = <0xa80000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi8_default>;
> + pinctrl-1 = <&qup_spi8_sleep>;
> + interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c9: i2c@a84000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0xa84000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c9_default>;
> + pinctrl-1 = <&qup_i2c9_sleep>;
> + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi9: spi@a84000 {
> + compatible = "qcom,geni-spi";
> + reg = <0xa84000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi9_default>;
> + pinctrl-1 = <&qup_spi9_sleep>;
> + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + uart9: serial@a84000 {
> + compatible = "qcom,geni-debug-uart";
> + reg = <0xa84000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_uart9_default>;
> + pinctrl-1 = <&qup_uart9_sleep>;
> + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> +
> + i2c10: i2c@a88000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0xa88000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c10_default>;
> + pinctrl-1 = <&qup_i2c10_sleep>;
> + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi10: spi@a88000 {
> + compatible = "qcom,geni-spi";
> + reg = <0xa88000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi10_default>;
> + pinctrl-1 = <&qup_spi10_sleep>;
> + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c11: i2c@a8c000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0xa8c000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c11_default>;
> + pinctrl-1 = <&qup_i2c11_sleep>;
> + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi11: spi@a8c000 {
> + compatible = "qcom,geni-spi";
> + reg = <0xa8c000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi11_default>;
> + pinctrl-1 = <&qup_spi11_sleep>;
> + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c12: i2c@a90000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0xa90000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c12_default>;
> + pinctrl-1 = <&qup_i2c12_sleep>;
> + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi12: spi@a90000 {
> + compatible = "qcom,geni-spi";
> + reg = <0xa90000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi12_default>;
> + pinctrl-1 = <&qup_spi12_sleep>;
> + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c13: i2c@a94000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0xa94000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c13_default>;
> + pinctrl-1 = <&qup_i2c13_sleep>;
> + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi13: spi@a94000 {
> + compatible = "qcom,geni-spi";
> + reg = <0xa94000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi13_default>;
> + pinctrl-1 = <&qup_spi13_sleep>;
> + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c14: i2c@a98000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0xa98000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c14_default>;
> + pinctrl-1 = <&qup_i2c14_sleep>;
> + interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi14: spi@a98000 {
> + compatible = "qcom,geni-spi";
> + reg = <0xa98000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi14_default>;
> + pinctrl-1 = <&qup_spi14_sleep>;
> + interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c15: i2c@a9c000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0xa9c000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_i2c15_default>;
> + pinctrl-1 = <&qup_i2c15_sleep>;
> + interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi15: spi@a9c000 {
> + compatible = "qcom,geni-spi";
> + reg = <0xa9c000 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_spi15_default>;
> + pinctrl-1 = <&qup_spi15_sleep>;
> + interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> + };
> +
> tcsr_mutex_regs: syscon@1f40000 {
> compatible = "syscon";
> reg = <0x1f40000 0x40000>;
> @@ -219,6 +738,500 @@
> #gpio-cells = <2>;
> interrupt-controller;
> #interrupt-cells = <2>;
> +
> + qup_i2c0_default: qup-i2c0-default {
> + pinmux {
> + pins = "gpio0", "gpio1";
> + function = "qup0";
> + };
> + };
> +
> + qup_i2c0_sleep: qup-i2c0-sleep {
> + pinmux {
> + pins = "gpio0", "gpio1";
> + function = "gpio";
> + };
> + };
> +
> + qup_i2c1_default: qup-i2c1-default {
> + pinmux {
> + pins = "gpio17", "gpio18";
> + function = "qup1";
> + };
> + };
> +
> + qup_i2c1_sleep: qup-i2c1-sleep {
> + pinmux {
> + pins = "gpio17", "gpio18";
> + function = "gpio";
> + };
> + };
> +
> + qup_i2c2_default: qup-i2c2-default {
> + pinmux {
> + pins = "gpio27", "gpio28";
> + function = "qup2";
> + };
> + };
> +
> + qup_i2c2_sleep: qup-i2c2-sleep {
> + pinmux {
> + pins = "gpio27", "gpio28";
> + function = "gpio";
> + };
> + };
> +
> + qup_i2c3_default: qup-i2c3-default {
> + pinmux {
> + pins = "gpio41", "gpio42";
> + function = "qup3";
> + };
> + };
> +
> + qup_i2c3_sleep: qup-i2c3-sleep {
> + pinmux {
> + pins = "gpio41", "gpio42";
> + function = "gpio";
> + };
> + };
> +
> + qup_i2c4_default: qup-i2c4-default {
> + pinmux {
> + pins = "gpio89", "gpio90";
> + function = "qup4";
> + };
> + };
> +
> + qup_i2c4_sleep: qup-i2c4-sleep {
> + pinmux {
> + pins = "gpio89", "gpio90";
> + function = "gpio";
> + };
> + };
> +
> + qup_i2c5_default: qup-i2c5-default {
> + pinmux {
> + pins = "gpio85", "gpio86";
> + function = "qup5";
> + };
> + };
> +
> + qup_i2c5_sleep: qup-i2c5-sleep {
> + pinmux {
> + pins = "gpio85", "gpio86";
> + function = "gpio";
> + };
> + };
> +
> + qup_i2c6_default: qup-i2c6-default {
> + pinmux {
> + pins = "gpio45", "gpio46";
> + function = "qup6";
> + };
> + };
> +
> + qup_i2c6_sleep: qup-i2c6-sleep {
> + pinmux {
> + pins = "gpio45", "gpio46";
> + function = "gpio";
> + };
> + };
> +
> + qup_i2c7_default: qup-i2c7-default {
> + pinmux {
> + pins = "gpio93", "gpio94";
> + function = "qup7";
> + };
> + };
> +
> + qup_i2c7_sleep: qup-i2c7-sleep {
> + pinmux {
> + pins = "gpio93", "gpio94";
> + function = "gpio";
> + };
> + };
> +
> + qup_i2c8_default: qup-i2c8-default {
> + pinmux {
> + pins = "gpio65", "gpio66";
> + function = "qup8";
> + };
> + };
> +
> + qup_i2c8_sleep: qup-i2c8-sleep {
> + pinmux {
> + pins = "gpio65", "gpio66";
> + function = "gpio";
> + };
> + };
> +
> + qup_i2c9_default: qup-i2c9-default {
> + pinmux {
> + pins = "gpio6", "gpio7";
> + function = "qup9";
> + };
> + };
> +
> + qup_i2c9_sleep: qup-i2c9-sleep {
> + pinmux {
> + pins = "gpio6", "gpio7";
> + function = "gpio";
> + };
> + };
> +
> + qup_i2c10_default: qup-i2c10-default {
> + pinmux {
> + pins = "gpio55", "gpio56";
> + function = "qup10";
> + };
> + };
> +
> + qup_i2c10_sleep: qup-i2c10-sleep {
> + pinmux {
> + pins = "gpio55", "gpio56";
> + function = "gpio";
> + };
> + };
> +
> + qup_i2c11_default: qup-i2c11-default {
> + pinmux {
> + pins = "gpio31", "gpio32";
> + function = "qup11";
> + };
> + };
> +
> + qup_i2c11_sleep: qup-i2c11-sleep {
> + pinmux {
> + pins = "gpio31", "gpio32";
> + function = "gpio";
> + };
> + };
> +
> + qup_i2c12_default: qup-i2c12-default {
> + pinmux {
> + pins = "gpio49", "gpio50";
> + function = "qup12";
> + };
> + };
> +
> + qup_i2c12_sleep: qup-i2c12-sleep {
> + pinmux {
> + pins = "gpio49", "gpio50";
> + function = "gpio";
> + };
> + };
> +
> + qup_i2c13_default: qup-i2c13-default {
> + pinmux {
> + pins = "gpio105", "gpio106";
> + function = "qup13";
> + };
> + };
> +
> + qup_i2c13_sleep: qup-i2c13-sleep {
> + pinmux {
> + pins = "gpio105", "gpio106";
> + function = "gpio";
> + };
> + };
> +
> + qup_i2c14_default: qup-i2c14-default {
> + pinmux {
> + pins = "gpio33", "gpio34";
> + function = "qup14";
> + };
> + };
> +
> + qup_i2c14_sleep: qup-i2c14-sleep {
> + pinmux {
> + pins = "gpio33", "gpio34";
> + function = "gpio";
> + };
> + };
> +
> + qup_i2c15_default: qup-i2c15-default {
> + pinmux {
> + pins = "gpio81", "gpio82";
> + function = "qup15";
> + };
> + };
> +
> + qup_i2c15_sleep: qup-i2c15-sleep {
> + pinmux {
> + pins = "gpio81", "gpio82";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi0_default: qup-spi0-default {
> + pinmux {
> + pins = "gpio0", "gpio1",
> + "gpio2", "gpio3";
> + function = "qup0";
> + };
> + };
> +
> + qup_spi0_sleep: qup-spi0-sleep {
> + pinmux {
> + pins = "gpio0", "gpio1",
> + "gpio2", "gpio3";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi1_default: qup-spi1-default {
> + pinmux {
> + pins = "gpio17", "gpio18",
> + "gpio19", "gpio20";
> + function = "qup1";
> + };
> + };
> +
> + qup_spi1_sleep: qup-spi1-sleep {
> + pinmux {
> + pins = "gpio17", "gpio18",
> + "gpio19", "gpio20";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi2_default: qup-spi2-default {
> + pinmux {
> + pins = "gpio27", "gpio28",
> + "gpio29", "gpio30";
> + function = "qup2";
> + };
> + };
> +
> + qup_spi2_sleep: qup-spi2-sleep {
> + pinmux {
> + pins = "gpio27", "gpio28",
> + "gpio29", "gpio30";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi3_default: qup-spi3-default {
> + pinmux {
> + pins = "gpio41", "gpio42",
> + "gpio43", "gpio44";
> + function = "qup3";
> + };
> + };
> +
> + qup_spi3_sleep: qup-spi3-sleep {
> + pinmux {
> + pins = "gpio41", "gpio42",
> + "gpio43", "gpio44";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi4_default: qup-spi4-default {
> + pinmux {
> + pins = "gpio89", "gpio90",
> + "gpio91", "gpio92";
> + function = "qup4";
> + };
> + };
> +
> + qup_spi4_sleep: qup-spi4-sleep {
> + pinmux {
> + pins = "gpio89", "gpio90",
> + "gpio91", "gpio92";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi5_default: qup-spi5-default {
> + pinmux {
> + pins = "gpio85", "gpio86",
> + "gpio87", "gpio88";
> + function = "qup5";
> + };
> + };
> +
> + qup_spi5_sleep: qup-spi5-sleep {
> + pinmux {
> + pins = "gpio85", "gpio86",
> + "gpio87", "gpio88";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi6_default: qup-spi6-default {
> + pinmux {
> + pins = "gpio45", "gpio46",
> + "gpio47", "gpio48";
> + function = "qup6";
> + };
> + };
> +
> + qup_spi6_sleep: qup-spi6-sleep {
> + pinmux {
> + pins = "gpio45", "gpio46",
> + "gpio47", "gpio48";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi7_default: qup-spi7-default {
> + pinmux {
> + pins = "gpio93", "gpio94",
> + "gpio95", "gpio96";
> + function = "qup7";
> + };
> + };
> +
> + qup_spi7_sleep: qup-spi7-sleep {
> + pinmux {
> + pins = "gpio93", "gpio94",
> + "gpio95", "gpio96";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi8_default: qup-spi8-default {
> + pinmux {
> + pins = "gpio65", "gpio66",
> + "gpio67", "gpio68";
> + function = "qup8";
> + };
> + };
> +
> + qup_spi8_sleep: qup-spi8-sleep {
> + pinmux {
> + pins = "gpio65", "gpio66",
> + "gpio67", "gpio68";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi9_default: qup-spi9-default {
> + pinmux {
> + pins = "gpio6", "gpio7",
> + "gpio4", "gpio5";
> + function = "qup9";
> + };
> + };
> +
> + qup_spi9_sleep: qup-spi9-sleep {
> + pinmux {
> + pins = "gpio6", "gpio7",
> + "gpio4", "gpio5";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi10_default: qup-spi10-default {
> + pinmux {
> + pins = "gpio55", "gpio56",
> + "gpio53", "gpio54";
> + function = "qup10";
> + };
> + };
> +
> + qup_spi10_sleep: qup-spi10-sleep {
> + pinmux {
> + pins = "gpio55", "gpio56",
> + "gpio53", "gpio54";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi11_default: qup-spi11-default {
> + pinmux {
> + pins = "gpio31", "gpio32",
> + "gpio33", "gpio34";
> + function = "qup11";
> + };
> + };
> +
> + qup_spi11_sleep: qup-spi11-sleep {
> + pinmux {
> + pins = "gpio31", "gpio32",
> + "gpio33", "gpio34";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi12_default: qup-spi12-default {
> + pinmux {
> + pins = "gpio49", "gpio50",
> + "gpio51", "gpio52";
> + function = "qup12";
> + };
> + };
> +
> + qup_spi12_sleep: qup-spi12-sleep {
> + pinmux {
> + pins = "gpio49", "gpio50",
> + "gpio51", "gpio52";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi13_default: qup-spi13-default {
> + pinmux {
> + pins = "gpio105", "gpio106",
> + "gpio107", "gpio108";
> + function = "qup13";
> + };
> + };
> +
> + qup_spi13_sleep: qup-spi13-sleep {
> + pinmux {
> + pins = "gpio105", "gpio106",
> + "gpio107", "gpio108";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi14_default: qup-spi14-default {
> + pinmux {
> + pins = "gpio33", "gpio34",
> + "gpio31", "gpio32";
> + function = "qup14";
> + };
> + };
> +
> + qup_spi14_sleep: qup-spi14-sleep {
> + pinmux {
> + pins = "gpio33", "gpio34",
> + "gpio31", "gpio32";
> + function = "gpio";
> + };
> + };
> +
> + qup_spi15_default: qup-spi15-default {
> + pinmux {
> + pins = "gpio81", "gpio82",
> + "gpio83", "gpio84";
> + function = "qup15";
> + };
> + };
> +
> + qup_spi15_sleep: qup-spi15-sleep {
> + pinmux {
> + pins = "gpio81", "gpio82",
> + "gpio83", "gpio84";
> + function = "gpio";
> + };
> + };
> +
> + qup_uart9_default: qup-uart9-default {
> + pinmux {
> + pins = "gpio4", "gpio5";
> + function = "qup9";
> + };
> + };
> +
> + qup_uart9_sleep: qup-uart9-sleep {
> + pinmux {
> + pins = "gpio4", "gpio5";
> + function = "gpio";
> + };
> + };
> };
>
> spmi_bus: spmi@c440000 {
> --
> 2.17.1.1185.g55be947832-goog
>
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH 2/2] arm64: dts: qcom: sdm845: Enable debug UART and I2C10 on sdm845-mtp
2018-06-07 20:46 ` [PATCH 2/2] arm64: dts: qcom: sdm845: Enable debug UART and I2C10 on sdm845-mtp Douglas Anderson
@ 2018-06-12 5:01 ` Bjorn Andersson
0 siblings, 0 replies; 5+ messages in thread
From: Bjorn Andersson @ 2018-06-12 5:01 UTC (permalink / raw)
To: Douglas Anderson
Cc: andy.gross, rnayak, kramasub, sdharia, swboyd, devicetree,
linux-arm-msm, linux-kernel, Rob Herring, David Brown,
Will Deacon, Mark Rutland, linux-soc, Catalin Marinas,
linux-arm-kernel
On Thu 07 Jun 13:46 PDT 2018, Douglas Anderson wrote:
> The debug UART is very useful to have. I2C10 is enabled as an example
> of a I2C port we can talk on for now. Eventually we'll want to put
> peripherals under it.
>
> Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Regards,
Bjorn
> ---
>
> arch/arm64/boot/dts/qcom/sdm845-mtp.dts | 52 +++++++++++++++++++++++++
> 1 file changed, 52 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> index 979ab49913f1..e1eda143a725 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> +++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> @@ -12,4 +12,56 @@
> / {
> model = "Qualcomm Technologies, Inc. SDM845 MTP";
> compatible = "qcom,sdm845-mtp";
> +
> + aliases {
> + serial0 = &uart9;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +};
> +
> +&i2c10 {
> + status = "okay";
> + clock-frequency = <400000>;
> +};
> +
> +&qupv3_id_1 {
> + status = "okay";
> +};
> +
> +&uart9 {
> + status = "okay";
> +};
> +
> +/* PINCTRL - additions to nodes defined in sdm845.dtsi */
> +
> +&qup_i2c10_default {
> + pinconf {
> + pins = "gpio55", "gpio56";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +};
> +
> +&qup_uart9_default {
> + pinconf-tx {
> + pins = "gpio4";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + pinconf-rx {
> + pins = "gpio5";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +};
> +
> +&qup_uart9_sleep {
> + pinconf {
> + pins = "gpio4", "gpio5";
> + bias-pull-down;
> + };
> };
> --
> 2.17.1.1185.g55be947832-goog
>
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH 1/2] arm64: dts: qcom: sdm845: Add I2C, SPI, and UART9 nodes
2018-06-12 5:01 ` [PATCH 1/2] arm64: dts: qcom: sdm845: Add I2C, SPI, and UART9 nodes Bjorn Andersson
@ 2018-06-12 5:22 ` Doug Anderson
0 siblings, 0 replies; 5+ messages in thread
From: Doug Anderson @ 2018-06-12 5:22 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Andy Gross, Rajendra Nayak, Karthikeyan Ramasubramanian,
Sagar Dharia, Stephen Boyd, devicetree, linux-arm-msm, LKML,
Rob Herring, David Brown, Will Deacon, Mark Rutland,
open list:ARM/QUALCOMM SUPPORT, Catalin Marinas, Linux ARM
Hi,
On Mon, Jun 11, 2018 at 10:01 PM, Bjorn Andersson
<bjorn.andersson@linaro.org> wrote:
> On Thu 07 Jun 13:46 PDT 2018, Douglas Anderson wrote:
>
>> This adds nodes to SDM845-dtsi for all the I2C ports, all the SPI
>> ports, and UART9. Note that I2C / SPI / UART are a bit strange on
>> sdm845 because each "serial engine" has 4 pins associated with it and
>> depending on which firmware has been loaded into the serial engine
>> (loaded by the BIOS) the serial engine can behave like an I2C port, a
>> SPI port, or a UART. As per the landed bindings that means that we
>> need to create one node for each possible mode that the port could be
>> in. With 16 serial engines that means 16 x 3 = 48 nodes.
>>
>> We get away with only creating 33 nodes for now because it seems very
>> likely that SDM845-based boards will actually all use the same UART
>> (UART 9) for debug purposes. While another UART could be used for
>> something like Bluetooth communication we can cross that path when we
>> come to it. Some documentation that I saw implied that using a UART
>> for "high speed" communications actually needs yet another different
>> serial engine firmware anyway.
>>
>> Note that quick measurements adding all these nodes adds ~10k of extra
>> space per dtb that they're included with. If this becomes a problem
>> we may need to think of a different way to structure this so that
>> boards only get the nodes they need (or figure out how to get dtc to
>> strip 'disabled' nodes). For now it seems OK.
>>
>> These nodes were programmatically generated with a fairly dumb python
>> script. See http://crosreview.com/1091631 for the source.
>>
>> Signed-off-by: Douglas Anderson <dianders@chromium.org>
>
> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Thanks for the review!
One note is that I have since come to find that it might not be so
wise to define the sleep pinctrl state here. For the SPI driver at
least I dug in and I saw the the sleep state is selected when we're
runtime PMed. ...and with the currently posted SPI driver that can
happen in some cases even when the chip select is supposed to be kept
low. For now it's more prudent to keep the "sleep" state out of the
device tree and we can always add it in later.
I'll plan to re-spin the patch on Wednesday (I'm unavailable tomorrow).
For other's reference: I chatted offline with Bjorn offline and this
sounded fine to him.
-Doug
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2018-06-12 5:22 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-06-07 20:46 [PATCH 1/2] arm64: dts: qcom: sdm845: Add I2C, SPI, and UART9 nodes Douglas Anderson
2018-06-07 20:46 ` [PATCH 2/2] arm64: dts: qcom: sdm845: Enable debug UART and I2C10 on sdm845-mtp Douglas Anderson
2018-06-12 5:01 ` Bjorn Andersson
2018-06-12 5:01 ` [PATCH 1/2] arm64: dts: qcom: sdm845: Add I2C, SPI, and UART9 nodes Bjorn Andersson
2018-06-12 5:22 ` Doug Anderson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).