Linux-ARM-MSM Archive on lore.kernel.org
 help / color / Atom feed
From: Mark Brown <broonie@kernel.org>
To: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Cc: agross@kernel.org, bjorn.andersson@linaro.org,
	broonie@kernel.org, devicetree@vger.kernel.org,
	lgirdwood@gmail.com, linux-arm-msm@vger.kernel.org,
	linux-kernel@vger.kernel.org, Mark Brown <broonie@kernel.org>,
	mark.rutland@arm.com, robh+dt@kernel.org
Subject: Applied "regulator: qcom_spmi: Add support for PM8005" to the regulator tree
Date: Tue, 18 Jun 2019 19:33:20 +0100 (BST)
Message-ID: <20190618183320.AC261440049@finisterre.sirena.org.uk> (raw)
In-Reply-To: <20190617183729.13553-1-jeffrey.l.hugo@gmail.com>

The patch

   regulator: qcom_spmi: Add support for PM8005

has been applied to the regulator tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git for-5.3

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

From 42ba89c8bbd95fce16122d357456ce1bd35d31d2 Mon Sep 17 00:00:00 2001
From: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Date: Mon, 17 Jun 2019 11:37:29 -0700
Subject: [PATCH] regulator: qcom_spmi: Add support for PM8005

The PM8005 is used on the msm8998 MTP.  The S1 regulator is VDD_GFX, ie
it needs to be on and controlled inorder to use the GPU.  Add support to
drive the PM8005 regulators so that we can bring up the GPU on msm8998.

Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 drivers/regulator/qcom_spmi-regulator.c | 176 ++++++++++++++++++++++++
 1 file changed, 176 insertions(+)

diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 00773a485fc1..ee38b1b63a3b 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -96,6 +96,7 @@ enum spmi_regulator_logical_type {
 	SPMI_REGULATOR_LOGICAL_TYPE_ULT_LO_SMPS,
 	SPMI_REGULATOR_LOGICAL_TYPE_ULT_HO_SMPS,
 	SPMI_REGULATOR_LOGICAL_TYPE_ULT_LDO,
+	SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS426,
 };
 
 enum spmi_regulator_type {
@@ -142,6 +143,7 @@ enum spmi_regulator_subtype {
 	SPMI_REGULATOR_SUBTYPE_5V_BOOST		= 0x01,
 	SPMI_REGULATOR_SUBTYPE_FTS_CTL		= 0x08,
 	SPMI_REGULATOR_SUBTYPE_FTS2p5_CTL	= 0x09,
+	SPMI_REGULATOR_SUBTYPE_FTS426_CTL	= 0x0a,
 	SPMI_REGULATOR_SUBTYPE_BB_2A		= 0x01,
 	SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL1	= 0x0d,
 	SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL2	= 0x0e,
@@ -162,6 +164,18 @@ enum spmi_common_regulator_registers {
 	SPMI_COMMON_REG_STEP_CTRL		= 0x61,
 };
 
+/*
+ * Second common register layout used by newer devices starting with ftsmps426
+ * Note that some of the registers from the first common layout remain
+ * unchanged and their definition is not duplicated.
+ */
+enum spmi_ftsmps426_regulator_registers {
+	SPMI_FTSMPS426_REG_VOLTAGE_LSB		= 0x40,
+	SPMI_FTSMPS426_REG_VOLTAGE_MSB		= 0x41,
+	SPMI_FTSMPS426_REG_VOLTAGE_ULS_LSB	= 0x68,
+	SPMI_FTSMPS426_REG_VOLTAGE_ULS_MSB	= 0x69,
+};
+
 enum spmi_vs_registers {
 	SPMI_VS_REG_OCP				= 0x4a,
 	SPMI_VS_REG_SOFT_START			= 0x4c,
@@ -221,6 +235,14 @@ enum spmi_common_control_register_index {
 #define SPMI_COMMON_MODE_FOLLOW_HW_EN0_MASK	0x01
 #define SPMI_COMMON_MODE_FOLLOW_ALL_MASK	0x1f
 
+#define SPMI_FTSMPS426_MODE_BYPASS_MASK		3
+#define SPMI_FTSMPS426_MODE_RETENTION_MASK	4
+#define SPMI_FTSMPS426_MODE_LPM_MASK		5
+#define SPMI_FTSMPS426_MODE_AUTO_MASK		6
+#define SPMI_FTSMPS426_MODE_HPM_MASK		7
+
+#define SPMI_FTSMPS426_MODE_MASK		0x07
+
 /* Common regulator pull down control register layout */
 #define SPMI_COMMON_PULL_DOWN_ENABLE_MASK	0x80
 
@@ -266,6 +288,23 @@ enum spmi_common_control_register_index {
 #define SPMI_FTSMPS_STEP_MARGIN_NUM	4
 #define SPMI_FTSMPS_STEP_MARGIN_DEN	5
 
+#define SPMI_FTSMPS426_STEP_CTRL_DELAY_MASK	0x03
+#define SPMI_FTSMPS426_STEP_CTRL_DELAY_SHIFT	0
+
+/* Clock rate in kHz of the FTSMPS426 regulator reference clock. */
+#define SPMI_FTSMPS426_CLOCK_RATE		4800
+
+/* Minimum voltage stepper delay for each step. */
+#define SPMI_FTSMPS426_STEP_DELAY		2
+
+/*
+ * The ratio SPMI_FTSMPS426_STEP_MARGIN_NUM/SPMI_FTSMPS426_STEP_MARGIN_DEN is
+ * used to adjust the step rate in order to account for oscillator variance.
+ */
+#define SPMI_FTSMPS426_STEP_MARGIN_NUM	10
+#define SPMI_FTSMPS426_STEP_MARGIN_DEN	11
+
+
 /* VSET value to decide the range of ULT SMPS */
 #define ULT_SMPS_RANGE_SPLIT 0x60
 
@@ -439,6 +478,10 @@ static struct spmi_voltage_range ftsmps2p5_ranges[] = {
 	SPMI_VOLTAGE_RANGE(1,  160000, 1360000, 2200000, 2200000, 10000),
 };
 
+static struct spmi_voltage_range ftsmps426_ranges[] = {
+	SPMI_VOLTAGE_RANGE(0,       0,  320000, 1352000, 1352000,  4000),
+};
+
 static struct spmi_voltage_range boost_ranges[] = {
 	SPMI_VOLTAGE_RANGE(0, 4000000, 4000000, 5550000, 5550000, 50000),
 };
@@ -472,6 +515,7 @@ static DEFINE_SPMI_SET_POINTS(ln_ldo);
 static DEFINE_SPMI_SET_POINTS(smps);
 static DEFINE_SPMI_SET_POINTS(ftsmps);
 static DEFINE_SPMI_SET_POINTS(ftsmps2p5);
+static DEFINE_SPMI_SET_POINTS(ftsmps426);
 static DEFINE_SPMI_SET_POINTS(boost);
 static DEFINE_SPMI_SET_POINTS(boost_byp);
 static DEFINE_SPMI_SET_POINTS(ult_lo_smps);
@@ -739,6 +783,23 @@ spmi_regulator_common_set_voltage(struct regulator_dev *rdev, unsigned selector)
 	return spmi_vreg_write(vreg, SPMI_COMMON_REG_VOLTAGE_RANGE, buf, 2);
 }
 
+static int spmi_regulator_common_list_voltage(struct regulator_dev *rdev,
+					      unsigned selector);
+
+static int spmi_regulator_ftsmps426_set_voltage(struct regulator_dev *rdev,
+					      unsigned selector)
+{
+	struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+	u8 buf[2];
+	int mV;
+
+	mV = spmi_regulator_common_list_voltage(rdev, selector) / 1000;
+
+	buf[0] = mV & 0xff;
+	buf[1] = mV >> 8;
+	return spmi_vreg_write(vreg, SPMI_FTSMPS426_REG_VOLTAGE_LSB, buf, 2);
+}
+
 static int spmi_regulator_set_voltage_time_sel(struct regulator_dev *rdev,
 		unsigned int old_selector, unsigned int new_selector)
 {
@@ -770,6 +831,21 @@ static int spmi_regulator_common_get_voltage(struct regulator_dev *rdev)
 	return spmi_hw_selector_to_sw(vreg, voltage_sel, range);
 }
 
+static int spmi_regulator_ftsmps426_get_voltage(struct regulator_dev *rdev)
+{
+	struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+	const struct spmi_voltage_range *range;
+	u8 buf[2];
+	int uV;
+
+	spmi_vreg_read(vreg, SPMI_FTSMPS426_REG_VOLTAGE_LSB, buf, 2);
+
+	uV = (((unsigned int)buf[1] << 8) | (unsigned int)buf[0]) * 1000;
+	range = vreg->set_points->range;
+
+	return (uV - range->set_point_min_uV) / range->step_uV;
+}
+
 static int spmi_regulator_single_map_voltage(struct regulator_dev *rdev,
 		int min_uV, int max_uV)
 {
@@ -915,6 +991,23 @@ static unsigned int spmi_regulator_common_get_mode(struct regulator_dev *rdev)
 	}
 }
 
+static unsigned int spmi_regulator_ftsmps426_get_mode(struct regulator_dev *rdev)
+{
+	struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+	u8 reg;
+
+	spmi_vreg_read(vreg, SPMI_COMMON_REG_MODE, &reg, 1);
+
+	switch (reg) {
+	case SPMI_FTSMPS426_MODE_HPM_MASK:
+		return REGULATOR_MODE_NORMAL;
+	case SPMI_FTSMPS426_MODE_AUTO_MASK:
+		return REGULATOR_MODE_FAST;
+	default:
+		return REGULATOR_MODE_IDLE;
+	}
+}
+
 static int
 spmi_regulator_common_set_mode(struct regulator_dev *rdev, unsigned int mode)
 {
@@ -937,6 +1030,30 @@ spmi_regulator_common_set_mode(struct regulator_dev *rdev, unsigned int mode)
 	return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_MODE, val, mask);
 }
 
+static int
+spmi_regulator_ftsmps426_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+	struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+	u8 mask = SPMI_FTSMPS426_MODE_MASK;
+	u8 val;
+
+	switch (mode) {
+	case REGULATOR_MODE_NORMAL:
+		val = SPMI_FTSMPS426_MODE_HPM_MASK;
+		break;
+	case REGULATOR_MODE_FAST:
+		val = SPMI_FTSMPS426_MODE_AUTO_MASK;
+		break;
+	case REGULATOR_MODE_IDLE:
+		val = SPMI_FTSMPS426_MODE_LPM_MASK;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_MODE, val, mask);
+}
+
 static int
 spmi_regulator_common_set_load(struct regulator_dev *rdev, int load_uA)
 {
@@ -1266,6 +1383,21 @@ static struct regulator_ops spmi_ult_ldo_ops = {
 	.set_soft_start		= spmi_regulator_common_set_soft_start,
 };
 
+static struct regulator_ops spmi_ftsmps426_ops = {
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= regulator_is_enabled_regmap,
+	.set_voltage_sel	= spmi_regulator_ftsmps426_set_voltage,
+	.set_voltage_time_sel	= spmi_regulator_set_voltage_time_sel,
+	.get_voltage_sel	= spmi_regulator_ftsmps426_get_voltage,
+	.map_voltage		= spmi_regulator_single_map_voltage,
+	.list_voltage		= spmi_regulator_common_list_voltage,
+	.set_mode		= spmi_regulator_ftsmps426_set_mode,
+	.get_mode		= spmi_regulator_ftsmps426_get_mode,
+	.set_load		= spmi_regulator_common_set_load,
+	.set_pull_down		= spmi_regulator_common_set_pull_down,
+};
+
 /* Maximum possible digital major revision value */
 #define INF 0xFF
 
@@ -1301,6 +1433,7 @@ static const struct spmi_regulator_mapping supported_regulators[] = {
 	SPMI_VREG(BOOST, 5V_BOOST, 0, INF, BOOST,  boost,  boost,       0),
 	SPMI_VREG(FTS,   FTS_CTL,  0, INF, FTSMPS, ftsmps, ftsmps, 100000),
 	SPMI_VREG(FTS, FTS2p5_CTL, 0, INF, FTSMPS, ftsmps, ftsmps2p5, 100000),
+	SPMI_VREG(FTS, FTS426_CTL, 0, INF, FTSMPS426, ftsmps426, ftsmps426, 100000),
 	SPMI_VREG(BOOST_BYP, BB_2A, 0, INF, BOOST_BYP, boost, boost_byp, 0),
 	SPMI_VREG(ULT_BUCK, ULT_HF_CTL1, 0, INF, ULT_LO_SMPS, ult_lo_smps,
 						ult_lo_smps,   100000),
@@ -1438,6 +1571,34 @@ static int spmi_regulator_init_slew_rate(struct spmi_regulator *vreg)
 	return ret;
 }
 
+static int spmi_regulator_init_slew_rate_ftsmps426(struct spmi_regulator *vreg)
+{
+	int ret;
+	u8 reg = 0;
+	int delay, slew_rate;
+	const struct spmi_voltage_range *range = &vreg->set_points->range[0];
+
+	ret = spmi_vreg_read(vreg, SPMI_COMMON_REG_STEP_CTRL, &reg, 1);
+	if (ret) {
+		dev_err(vreg->dev, "spmi read failed, ret=%d\n", ret);
+		return ret;
+	}
+
+	delay = reg & SPMI_FTSMPS426_STEP_CTRL_DELAY_MASK;
+	delay >>= SPMI_FTSMPS426_STEP_CTRL_DELAY_SHIFT;
+
+	/* slew_rate has units of uV/us */
+	slew_rate = SPMI_FTSMPS426_CLOCK_RATE * range->step_uV;
+	slew_rate /= 1000 * (SPMI_FTSMPS426_STEP_DELAY << delay);
+	slew_rate *= SPMI_FTSMPS426_STEP_MARGIN_NUM;
+	slew_rate /= SPMI_FTSMPS426_STEP_MARGIN_DEN;
+
+	/* Ensure that the slew rate is greater than 0 */
+	vreg->slew_rate = max(slew_rate, 1);
+
+	return ret;
+}
+
 static int spmi_regulator_init_registers(struct spmi_regulator *vreg,
 				const struct spmi_regulator_init_data *data)
 {
@@ -1577,6 +1738,12 @@ static int spmi_regulator_of_parse(struct device_node *node,
 		ret = spmi_regulator_init_slew_rate(vreg);
 		if (ret)
 			return ret;
+		break;
+	case SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS426:
+		ret = spmi_regulator_init_slew_rate_ftsmps426(vreg);
+		if (ret)
+			return ret;
+		break;
 	default:
 		break;
 	}
@@ -1733,7 +1900,16 @@ static const struct spmi_regulator_data pmi8994_regulators[] = {
 	{ }
 };
 
+static const struct spmi_regulator_data pm8005_regulators[] = {
+	{ "s1", 0x1400, "vdd_s1", },
+	{ "s2", 0x1700, "vdd_s2", },
+	{ "s3", 0x1a00, "vdd_s3", },
+	{ "s4", 0x1d00, "vdd_s4", },
+	{ }
+};
+
 static const struct of_device_id qcom_spmi_regulator_match[] = {
+	{ .compatible = "qcom,pm8005-regulators", .data = &pm8005_regulators },
 	{ .compatible = "qcom,pm8841-regulators", .data = &pm8841_regulators },
 	{ .compatible = "qcom,pm8916-regulators", .data = &pm8916_regulators },
 	{ .compatible = "qcom,pm8941-regulators", .data = &pm8941_regulators },
-- 
2.20.1


  reply index

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-06-17 18:36 [PATCH v5 0/5] PM8005 and PMS405 regulator support Jeffrey Hugo
2019-06-17 18:37 ` [PATCH v5 1/5] dt-bindings: qcom_spmi: Document PM8005 regulators Jeffrey Hugo
2019-06-18 18:33   ` Applied "dt-bindings: qcom_spmi: Document PM8005 regulators" to the regulator tree Mark Brown
2019-06-17 18:37 ` [PATCH v5 2/5] regulator: qcom_spmi: Add support for PM8005 Jeffrey Hugo
2019-06-18 18:33   ` Mark Brown [this message]
2019-06-17 18:37 ` [PATCH v5 3/5] arm64: dts: msm8998-mtp: Add pm8005_s1 regulator Jeffrey Hugo
2019-06-18 18:33   ` Applied "arm64: dts: msm8998-mtp: Add pm8005_s1 regulator" to the regulator tree Mark Brown
2019-06-17 18:38 ` [PATCH v5 4/5] dt-bindings: qcom_spmi: Document pms405 support Jeffrey Hugo
2019-06-18 18:33   ` Applied "dt-bindings: qcom_spmi: Document pms405 support" to the regulator tree Mark Brown
2019-06-17 18:38 ` [PATCH v5 5/5] regulator: qcom_spmi: add PMS405 SPMI regulator Jeffrey Hugo
2019-06-18 18:33   ` Applied "regulator: qcom_spmi: add PMS405 SPMI regulator" to the regulator tree Mark Brown

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190618183320.AC261440049@finisterre.sirena.org.uk \
    --to=broonie@kernel.org \
    --cc=agross@kernel.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=jeffrey.l.hugo@gmail.com \
    --cc=lgirdwood@gmail.com \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-ARM-MSM Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-msm/0 linux-arm-msm/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-msm linux-arm-msm/ https://lore.kernel.org/linux-arm-msm \
		linux-arm-msm@vger.kernel.org linux-arm-msm@archiver.kernel.org
	public-inbox-index linux-arm-msm


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-arm-msm


AGPL code for this site: git clone https://public-inbox.org/ public-inbox