From: Robert Foss <robert.foss@linaro.org>
To: agross@kernel.org, bjorn.andersson@linaro.org,
robh+dt@kernel.org, mark.rutland@arm.com,
catalin.marinas@arm.com, will@kernel.org, shawnguo@kernel.org,
olof@lixom.net, Anson.Huang@nxp.com, maxime@cerno.tech,
leonard.crestez@nxp.com, dinguyen@kernel.org,
marcin.juszkiewicz@linaro.org, linux-arm-msm@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
Loic Poulain <loic.poulain@linaro.org>
Cc: Robert Foss <robert.foss@linaro.org>
Subject: [v1 2/6] arm64: dts: apq8016-sbc: Add CCI/Sensor nodes
Date: Wed, 11 Mar 2020 13:34:57 +0100 [thread overview]
Message-ID: <20200311123501.18202-3-robert.foss@linaro.org> (raw)
In-Reply-To: <20200311123501.18202-1-robert.foss@linaro.org>
From: Loic Poulain <loic.poulain@linaro.org>
Add cci device to msm8916.dtsi.
Add default 96boards camera node for db410c (apq8016-sbc).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
---
arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 75 +++++++++++++++++++++++
1 file changed, 75 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
index 037e26b3f8d5..a3e6982f4f93 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
@@ -495,6 +495,81 @@
wcnss@a21b000 {
status = "okay";
};
+
+ camera_vdddo_1v8: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "camera_vdddo";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ camera_vdda_2v8: fixedregulator@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "camera_vdda";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ camera_vddd_1v5: fixedregulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "camera_vddd";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ };
+
+ cci@1b0c000 {
+ status = "ok";
+ i2c-bus@0 {
+ camera_rear@3b {
+ compatible = "ovti,ov5640";
+ reg = <0x3b>;
+
+ enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&camera_rear_default>;
+
+ clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+ clock-names = "xclk";
+ clock-frequency = <23880000>;
+
+ vdddo-supply = <&camera_vdddo_1v8>;
+ vdda-supply = <&camera_vdda_2v8>;
+ vddd-supply = <&camera_vddd_1v5>;
+
+ /* No camera mezzanine by default */
+ status = "okay";
+
+ port {
+ ov5640_ep: endpoint {
+ clock-lanes = <1>;
+ data-lanes = <0 2>;
+ remote-endpoint = <&csiphy0_ep>;
+ };
+ };
+ };
+ };
+ };
+
+ camss@1b00000 {
+ status = "ok";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ csiphy0_ep: endpoint {
+ clock-lanes = <1>;
+ data-lanes = <0 2>;
+ remote-endpoint = <&ov5640_ep>;
+ status = "okay";
+ };
+ };
+ };
+ };
};
usb2513 {
--
2.20.1
next prev parent reply other threads:[~2020-03-11 12:35 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-03-11 12:34 [v1 0/6] Qualcomm CCI & Camera for db410c & db845c Robert Foss
2020-03-11 12:34 ` [v1 1/6] arm64: dts: msm8916: Add i2c-qcom-cci node Robert Foss
2020-03-12 4:50 ` Bjorn Andersson
2020-03-11 12:34 ` Robert Foss [this message]
2020-03-12 5:03 ` [v1 2/6] arm64: dts: apq8016-sbc: Add CCI/Sensor nodes Bjorn Andersson
2020-03-11 12:34 ` [v1 3/6] arm64: dts: sdm845: Add i2c-qcom-cci node Robert Foss
2020-03-12 5:12 ` Bjorn Andersson
2020-03-11 12:34 ` [v1 4/6] arm64: dts: sdm845-db845c: Add pm_8998 gpio names Robert Foss
2020-03-12 5:13 ` Bjorn Andersson
2020-03-11 12:35 ` [v1 5/6] arm64: dts: sdm845-db845c: Add ov8856 & ov7251 camera nodes Robert Foss
2020-03-12 5:34 ` Bjorn Andersson
2020-03-11 12:35 ` [v1 6/6] arm64: defconfig: Enable QCOM CAMCC, CAMSS and CCI drivers Robert Foss
2020-03-12 5:35 ` Bjorn Andersson
2020-03-17 13:54 ` Robert Foss
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200311123501.18202-3-robert.foss@linaro.org \
--to=robert.foss@linaro.org \
--cc=Anson.Huang@nxp.com \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=catalin.marinas@arm.com \
--cc=devicetree@vger.kernel.org \
--cc=dinguyen@kernel.org \
--cc=leonard.crestez@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=loic.poulain@linaro.org \
--cc=marcin.juszkiewicz@linaro.org \
--cc=mark.rutland@arm.com \
--cc=maxime@cerno.tech \
--cc=olof@lixom.net \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).