From: Vinod Koul <vkoul@kernel.org>
To: Wesley Cheng <wcheng@codeaurora.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: agross@kernel.org, mturquette@baylibre.com, sboyd@kernel.org,
robh+dt@kernel.org, mark.rutland@arm.com,
linux-arm-msm@vger.kernel.org, linux-clk@vger.kernel.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
Jack Pham <jackp@codeaurora.org>
Subject: Re: [PATCH v4 2/2] arm64: dts: qcom: sm8150: Add USB and PHY device nodes
Date: Tue, 16 Jun 2020 12:06:44 +0530 [thread overview]
Message-ID: <20200616063644.GA2324254@vkoul-mobl> (raw)
In-Reply-To: <1586566362-21450-3-git-send-email-wcheng@codeaurora.org>
On 10-04-20, 17:52, Wesley Cheng wrote:
> From: Jack Pham <jackp@codeaurora.org>
>
> Add device nodes for the USB3 controller, QMP SS PHY and
> SNPS HS PHY.
Bjorn, can you please review/pick this.. I dont see this in -rc1
>
> Signed-off-by: Jack Pham <jackp@codeaurora.org>
> Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Reviewed-by: Vinod Koul <vkoul@kernel.org>
> Tested-by: Vinod Koul <vinod.koul@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 21 ++++++++
> arch/arm64/boot/dts/qcom/sm8150.dtsi | 92 +++++++++++++++++++++++++++++++++
> 2 files changed, 113 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8150-mtp.dts b/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
> index 8ab1661..6c6325c 100644
> --- a/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
> @@ -408,3 +408,24 @@
> vdda-pll-supply = <&vreg_l3c_1p2>;
> vdda-pll-max-microamp = <19000>;
> };
> +
> +&usb_1_hsphy {
> + status = "okay";
> + vdda-pll-supply = <&vdd_usb_hs_core>;
> + vdda33-supply = <&vdda_usb_hs_3p1>;
> + vdda18-supply = <&vdda_usb_hs_1p8>;
> +};
> +
> +&usb_1_qmpphy {
> + status = "okay";
> + vdda-phy-supply = <&vreg_l3c_1p2>;
> + vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
> +};
> +
> +&usb_1 {
> + status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> + dr_mode = "peripheral";
> +};
> diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> index 141c21d..a36512d 100644
> --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> @@ -621,6 +621,98 @@
> };
> };
>
> + usb_1_hsphy: phy@88e2000 {
> + compatible = "qcom,sm8150-usb-hs-phy",
> + "qcom,usb-snps-hs-7nm-phy";
> + reg = <0 0x088e2000 0 0x400>;
> + status = "disabled";
> + #phy-cells = <0>;
> +
> + clocks = <&rpmhcc RPMH_CXO_CLK>;
> + clock-names = "ref";
> +
> + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
> + };
> +
> + usb_1_qmpphy: phy@88e9000 {
> + compatible = "qcom,sm8150-qmp-usb3-phy";
> + reg = <0 0x088e9000 0 0x18c>,
> + <0 0x088e8000 0 0x10>;
> + reg-names = "reg-base", "dp_com";
> + status = "disabled";
> + #clock-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
> + <&rpmhcc RPMH_CXO_CLK>,
> + <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
> + <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
> + clock-names = "aux", "ref_clk_src", "ref", "com_aux";
> +
> + resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
> + <&gcc GCC_USB3_PHY_PRIM_BCR>;
> + reset-names = "phy", "common";
> +
> + usb_1_ssphy: lanes@88e9200 {
> + reg = <0 0x088e9200 0 0x200>,
> + <0 0x088e9400 0 0x200>,
> + <0 0x088e9c00 0 0x218>,
> + <0 0x088e9600 0 0x200>,
> + <0 0x088e9800 0 0x200>,
> + <0 0x088e9a00 0 0x100>;
> + #phy-cells = <0>;
> + clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "usb3_phy_pipe_clk_src";
> + };
> + };
> +
> + usb_1: usb@a6f8800 {
> + compatible = "qcom,sm8150-dwc3", "qcom,dwc3";
> + reg = <0 0x0a6f8800 0 0x400>;
> + status = "disabled";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> + dma-ranges;
> +
> + clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
> + <&gcc GCC_USB30_PRIM_MASTER_CLK>,
> + <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
> + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
> + <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
> + <&gcc GCC_USB3_SEC_CLKREF_CLK>;
> + clock-names = "cfg_noc", "core", "iface", "mock_utmi",
> + "sleep", "xo";
> +
> + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
> + <&gcc GCC_USB30_PRIM_MASTER_CLK>;
> + assigned-clock-rates = <19200000>, <150000000>;
> +
> + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "hs_phy_irq", "ss_phy_irq",
> + "dm_hs_phy_irq", "dp_hs_phy_irq";
> +
> + power-domains = <&gcc USB30_PRIM_GDSC>;
> +
> + resets = <&gcc GCC_USB30_PRIM_BCR>;
> +
> + usb_1_dwc3: dwc3@a600000 {
> + compatible = "snps,dwc3";
> + reg = <0 0x0a600000 0 0xcd00>;
> + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
> + snps,dis_u2_susphy_quirk;
> + snps,dis_enblslpm_quirk;
> + phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
> + phy-names = "usb2-phy", "usb3-phy";
> + };
> + };
> +
> aoss_qmp: power-controller@c300000 {
> compatible = "qcom,sm8150-aoss-qmp";
> reg = <0x0 0x0c300000 0x0 0x100000>;
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
--
~Vinod
prev parent reply other threads:[~2020-06-16 6:36 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-04-11 0:52 [PATCH v4 0/2] Enable SS/HS USB support on SM8150 Wesley Cheng
2020-04-11 0:52 ` [PATCH v4 1/2] clk: qcom: gcc: Add USB3 PIPE clock and GDSC for SM8150 Wesley Cheng
2020-04-11 1:01 ` Bjorn Andersson
2020-04-22 9:23 ` Stephen Boyd
2020-04-11 0:52 ` [PATCH v4 2/2] arm64: dts: qcom: sm8150: Add USB and PHY device nodes Wesley Cheng
2020-06-16 6:36 ` Vinod Koul [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200616063644.GA2324254@vkoul-mobl \
--to=vkoul@kernel.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=jackp@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mturquette@baylibre.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=wcheng@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).