Linux-ARM-MSM Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH v8 00/11] qcom: pm8150: add support for thermal monitoring
@ 2020-10-09 15:44 Dmitry Baryshkov
  2020-10-09 15:44 ` [PATCH v8 01/11] dt-bindings: thermal: qcom: add adc-thermal monitor bindings Dmitry Baryshkov
                   ` (10 more replies)
  0 siblings, 11 replies; 13+ messages in thread
From: Dmitry Baryshkov @ 2020-10-09 15:44 UTC (permalink / raw)
  To: Andy Gross, Bjorn Andersson, Rob Herring, Zhang Rui,
	Daniel Lezcano, Amit Kucheria, Jonathan Cameron, Hartmut Knaack,
	Lars-Peter Clausen, Peter Meerwald-Stadler
  Cc: linux-arm-msm, linux-pm, devicetree, linux-iio,
	Manivannan Sadhasivam, Jishnu Prakash



This patch serie adds support for thermal monitoring block on Qualcomm's
PMIC5 chips. PM8150{,b,l} and sm8250-mtp board device trees are extended
to support thermal zones provided by this thermal monitoring block.
Unlike the rest of PMIC thermal senses, these thermal zones describe
particular thermistors, which differ between from board to board.

Changes since v7:
 - Move qcom-vadc-common.h header to include/linux/iio/adc/ dir.
 - Use explicit sizeof(var) instead of hand-coding 1 when accessing
   adc-tm registers.
 - Remove buffer read from adc_tm5_init().
 - Remove extra on-stack var from adc_tm5_get_temp().
 - Minor formatting changes as suggested Daniel.

Changes since v6:
 - Added include <linux/bitfield.h> as noted by Jishnu Prakash.

Changes since v5:
 - Reworked DT bindings:
   * Removed qcom,adc-channel, instead it is parsed from io-channels
   * Renamed qcom,hw-settle-time to include -us suffix
 - Re-added monitor enabling which got lost during refactored. Noted by
   Jishnu Prakash.
 - Use threaded IRQ handler as susggested by Jishnu.

Changes since v4:
 - Added kernel-doc comments to ADC-TM structures
 - Used several sizeof(buf) instead of hand-conding register size

Changes since v3:
 - Fix DT description to spell "thermal monitoring" instead of just TM
 - Fix warnings in DT example
 - Add EXPORT_SYMBOL_GPL(of_iio_channel_get_by_name)
 - Fixed whitespace chanes in qcom-vadc-common.c
 - Removed error message if IIO chanel get returns -EPROBE_DEFER

Changes since v2:
 - IIO: export of_iio_channel_get_by_name() function
 - dt-bindings: move individual io-channels to each thermal monitoring
   channel rather than listing them all in device node
 - added fallback defaults to of_device_get_match_data calls in
   qcom-spmi-adc5 and qcom-spmi-adc-tm5 drivers
 - minor typo fixes

Changes since v1:
 - Introduce fixp_linear_interpolate() by Craig Tatlor
 - Lots of syntax/whitespace changes
 - Cleaned up register definitions per Jonathan's suggestion
 - Implemented most of the suggestions from Bjorn's and Jonathan's
   review






^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v8 01/11] dt-bindings: thermal: qcom: add adc-thermal monitor bindings
  2020-10-09 15:44 [PATCH v8 00/11] qcom: pm8150: add support for thermal monitoring Dmitry Baryshkov
@ 2020-10-09 15:44 ` Dmitry Baryshkov
  2020-10-09 15:44 ` [PATCH v8 02/11] fixp-arith: add a linear interpolation function Dmitry Baryshkov
                   ` (9 subsequent siblings)
  10 siblings, 0 replies; 13+ messages in thread
From: Dmitry Baryshkov @ 2020-10-09 15:44 UTC (permalink / raw)
  To: Andy Gross, Bjorn Andersson, Rob Herring, Zhang Rui,
	Daniel Lezcano, Amit Kucheria, Jonathan Cameron, Hartmut Knaack,
	Lars-Peter Clausen, Peter Meerwald-Stadler
  Cc: linux-arm-msm, linux-pm, devicetree, linux-iio,
	Manivannan Sadhasivam, Jishnu Prakash, Rob Herring

Add bindings for thermal monitor, part of Qualcomm PMIC5 chips. It is a
close counterpart of VADC part of those PMICs.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../bindings/thermal/qcom-spmi-adc-tm5.yaml   | 154 ++++++++++++++++++
 1 file changed, 154 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm5.yaml

diff --git a/Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm5.yaml b/Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm5.yaml
new file mode 100644
index 000000000000..9da2b349030d
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm5.yaml
@@ -0,0 +1,154 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/qcom-spmi-adc-tm5.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm's SPMI PMIC ADC Thermal Monitoring
+maintainers:
+  - Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
+
+properties:
+  compatible:
+    const: qcom,spmi-adc-tm5
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  "#thermal-sensor-cells":
+    const: 1
+    description:
+      Number of cells required to uniquely identify the thermal sensors. Since
+      we have multiple sensors this is set to 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  qcom,avg-samples:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Number of samples to be used for measurement.
+    enum:
+      - 1
+      - 2
+      - 4
+      - 8
+      - 16
+    default: 1
+
+  qcom,decimation:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: This parameter is used to decrease ADC sampling rate.
+            Quicker measurements can be made by reducing decimation ratio.
+    enum:
+      - 250
+      - 420
+      - 840
+    default: 840
+
+patternProperties:
+  "^([-a-z0-9]*)@[0-7]$":
+    type: object
+    description:
+      Represent one thermal sensor.
+
+    properties:
+      reg:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Specify the sensor channel. There are 8 channels in PMIC5's ADC TM
+        minimum: 0
+        maximum: 7
+
+      io-channels:
+        description:
+          From common IIO binding. Used to pipe PMIC ADC channel to thermal monitor
+
+      qcom,ratiometric:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Channel calibration type.
+          If this property is specified VADC will use the VDD reference
+          (1.875V) and GND for channel calibration. If property is not found,
+          channel will be calibrated with 0V and 1.25V reference channels,
+          also known as absolute calibration.
+
+      qcom,hw-settle-time-us:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Time between AMUX getting configured and the ADC starting conversion.
+        enum: [15, 100, 200, 300, 400, 500, 600, 700, 1000, 2000, 4000, 8000, 16000, 32000, 64000, 128000]
+
+      qcom,pre-scaling:
+        $ref: /schemas/types.yaml#/definitions/uint32-array
+        description: Used for scaling the channel input signal before the
+          signal is fed to VADC. The configuration for this node is to know the
+          pre-determined ratio and use it for post scaling. It is a pair of
+          integers, denoting the numerator and denominator of the fraction by
+          which input signal is multiplied. For example, <1 3> indicates the
+          signal is scaled down to 1/3 of its value before ADC measurement.  If
+          property is not found default value depending on chip will be used.
+        items:
+          - const: 1
+          - enum: [ 1, 3, 4, 6, 20, 8, 10 ]
+
+    required:
+      - reg
+      - io-channels
+
+    additionalProperties:
+      false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - "#address-cells"
+  - "#size-cells"
+  - "#thermal-sensor-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/iio/qcom,spmi-vadc.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    spmi_bus {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        pm8150b_adc: adc@3100 {
+            reg = <0x3100>;
+            compatible = "qcom,spmi-adc5";
+            #address-cells = <1>;
+            #size-cells = <0>;
+            #io-channel-cells = <1>;
+            io-channel-ranges;
+
+            /* Other propreties are omitted */
+            conn-therm@4f {
+                reg = <ADC5_AMUX_THM3_100K_PU>;
+                qcom,ratiometric;
+                qcom,hw-settle-time = <200>;
+            };
+        };
+
+        pm8150b_adc_tm: adc-tm@3500 {
+            compatible = "qcom,spmi-adc-tm5";
+            reg = <0x3500>;
+            interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+            #thermal-sensor-cells = <1>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            conn-therm@0 {
+                reg = <0>;
+                io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>;
+                qcom,ratiometric;
+                qcom,hw-settle-time-us = <200>;
+            };
+        };
+    };
+...
-- 
2.28.0


^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v8 02/11] fixp-arith: add a linear interpolation function
  2020-10-09 15:44 [PATCH v8 00/11] qcom: pm8150: add support for thermal monitoring Dmitry Baryshkov
  2020-10-09 15:44 ` [PATCH v8 01/11] dt-bindings: thermal: qcom: add adc-thermal monitor bindings Dmitry Baryshkov
@ 2020-10-09 15:44 ` Dmitry Baryshkov
  2020-10-09 15:44 ` [PATCH v8 03/11] iio: adc: qcom-vadc: move several adc5 functions to common file Dmitry Baryshkov
                   ` (8 subsequent siblings)
  10 siblings, 0 replies; 13+ messages in thread
From: Dmitry Baryshkov @ 2020-10-09 15:44 UTC (permalink / raw)
  To: Andy Gross, Bjorn Andersson, Rob Herring, Zhang Rui,
	Daniel Lezcano, Amit Kucheria, Jonathan Cameron, Hartmut Knaack,
	Lars-Peter Clausen, Peter Meerwald-Stadler
  Cc: linux-arm-msm, linux-pm, devicetree, linux-iio,
	Manivannan Sadhasivam, Jishnu Prakash, Craig Tatlor,
	Jonathan Cameron

From: Craig Tatlor <ctatlor97@gmail.com>

Adds a function to interpolate against two points,
this is carried arount as a helper function by tons of drivers.

Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
---
 include/linux/fixp-arith.h | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/include/linux/fixp-arith.h b/include/linux/fixp-arith.h
index 8396013785ef..281cb4f83dbe 100644
--- a/include/linux/fixp-arith.h
+++ b/include/linux/fixp-arith.h
@@ -141,4 +141,23 @@ static inline s32 fixp_sin32_rad(u32 radians, u32 twopi)
 #define fixp_cos32_rad(rad, twopi)	\
 	fixp_sin32_rad(rad + twopi / 4, twopi)
 
+/**
+ * fixp_linear_interpolate() - interpolates a value from two known points
+ *
+ * @x0: x value of point 0
+ * @y0: y value of point 0
+ * @x1: x value of point 1
+ * @y1: y value of point 1
+ * @x: the linear interpolant
+ */
+static inline int fixp_linear_interpolate(int x0, int y0, int x1, int y1, int x)
+{
+	if (y0 == y1 || x == x0)
+		return y0;
+	if (x1 == x0 || x == x1)
+		return y1;
+
+	return y0 + ((y1 - y0) * (x - x0) / (x1 - x0));
+}
+
 #endif
-- 
2.28.0


^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v8 03/11] iio: adc: qcom-vadc: move several adc5 functions to common file
  2020-10-09 15:44 [PATCH v8 00/11] qcom: pm8150: add support for thermal monitoring Dmitry Baryshkov
  2020-10-09 15:44 ` [PATCH v8 01/11] dt-bindings: thermal: qcom: add adc-thermal monitor bindings Dmitry Baryshkov
  2020-10-09 15:44 ` [PATCH v8 02/11] fixp-arith: add a linear interpolation function Dmitry Baryshkov
@ 2020-10-09 15:44 ` Dmitry Baryshkov
  2020-10-09 15:44 ` [PATCH v8 04/11] iio: adc: qcom-vadc-common: use fixp_linear_interpolate Dmitry Baryshkov
                   ` (7 subsequent siblings)
  10 siblings, 0 replies; 13+ messages in thread
From: Dmitry Baryshkov @ 2020-10-09 15:44 UTC (permalink / raw)
  To: Andy Gross, Bjorn Andersson, Rob Herring, Zhang Rui,
	Daniel Lezcano, Amit Kucheria, Jonathan Cameron, Hartmut Knaack,
	Lars-Peter Clausen, Peter Meerwald-Stadler
  Cc: linux-arm-msm, linux-pm, devicetree, linux-iio,
	Manivannan Sadhasivam, Jishnu Prakash, Jonathan Cameron

ADC-TM5 driver will make use of several functions from ADC5 driver. Move
them to qcom-vadc-common driver.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
---
 drivers/iio/adc/qcom-spmi-adc5.c   | 75 +++---------------------------
 drivers/iio/adc/qcom-vadc-common.c | 68 ++++++++++++++++++++++++++-
 drivers/iio/adc/qcom-vadc-common.h | 10 +++-
 3 files changed, 82 insertions(+), 71 deletions(-)

diff --git a/drivers/iio/adc/qcom-spmi-adc5.c b/drivers/iio/adc/qcom-spmi-adc5.c
index c10aa28be70a..c2da8f068b87 100644
--- a/drivers/iio/adc/qcom-spmi-adc5.c
+++ b/drivers/iio/adc/qcom-spmi-adc5.c
@@ -154,18 +154,6 @@ struct adc5_chip {
 	const struct adc5_data	*data;
 };
 
-static const struct vadc_prescale_ratio adc5_prescale_ratios[] = {
-	{.num =  1, .den =  1},
-	{.num =  1, .den =  3},
-	{.num =  1, .den =  4},
-	{.num =  1, .den =  6},
-	{.num =  1, .den = 20},
-	{.num =  1, .den =  8},
-	{.num = 10, .den = 81},
-	{.num =  1, .den = 10},
-	{.num =  1, .den = 16}
-};
-
 static int adc5_read(struct adc5_chip *adc, u16 offset, u8 *data, int len)
 {
 	return regmap_bulk_read(adc->regmap, adc->base + offset, data, len);
@@ -181,55 +169,6 @@ static int adc5_masked_write(struct adc5_chip *adc, u16 offset, u8 mask, u8 val)
 	return regmap_update_bits(adc->regmap, adc->base + offset, mask, val);
 }
 
-static int adc5_prescaling_from_dt(u32 num, u32 den)
-{
-	unsigned int pre;
-
-	for (pre = 0; pre < ARRAY_SIZE(adc5_prescale_ratios); pre++)
-		if (adc5_prescale_ratios[pre].num == num &&
-		    adc5_prescale_ratios[pre].den == den)
-			break;
-
-	if (pre == ARRAY_SIZE(adc5_prescale_ratios))
-		return -EINVAL;
-
-	return pre;
-}
-
-static int adc5_hw_settle_time_from_dt(u32 value,
-					const unsigned int *hw_settle)
-{
-	unsigned int i;
-
-	for (i = 0; i < VADC_HW_SETTLE_SAMPLES_MAX; i++) {
-		if (value == hw_settle[i])
-			return i;
-	}
-
-	return -EINVAL;
-}
-
-static int adc5_avg_samples_from_dt(u32 value)
-{
-	if (!is_power_of_2(value) || value > ADC5_AVG_SAMPLES_MAX)
-		return -EINVAL;
-
-	return __ffs(value);
-}
-
-static int adc5_decimation_from_dt(u32 value,
-					const unsigned int *decimation)
-{
-	unsigned int i;
-
-	for (i = 0; i < ADC5_DECIMATION_SAMPLES_MAX; i++) {
-		if (value == decimation[i])
-			return i;
-	}
-
-	return -EINVAL;
-}
-
 static int adc5_read_voltage_data(struct adc5_chip *adc, u16 *data)
 {
 	int ret;
@@ -511,7 +450,7 @@ static int adc_read_raw_common(struct iio_dev *indio_dev,
 			return ret;
 
 		ret = qcom_adc5_hw_scale(prop->scale_fn_type,
-			&adc5_prescale_ratios[prop->prescale],
+			prop->prescale,
 			adc->data,
 			adc_code_volt, val);
 		if (ret)
@@ -717,7 +656,7 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
 
 	ret = of_property_read_u32(node, "qcom,decimation", &value);
 	if (!ret) {
-		ret = adc5_decimation_from_dt(value, data->decimation);
+		ret = qcom_adc5_decimation_from_dt(value, data->decimation);
 		if (ret < 0) {
 			dev_err(dev, "%02x invalid decimation %d\n",
 				chan, value);
@@ -730,7 +669,7 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
 
 	ret = of_property_read_u32_array(node, "qcom,pre-scaling", varr, 2);
 	if (!ret) {
-		ret = adc5_prescaling_from_dt(varr[0], varr[1]);
+		ret = qcom_adc5_prescaling_from_dt(varr[0], varr[1]);
 		if (ret < 0) {
 			dev_err(dev, "%02x invalid pre-scaling <%d %d>\n",
 				chan, varr[0], varr[1]);
@@ -759,11 +698,9 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
 		if ((dig_version[0] >= ADC5_HW_SETTLE_DIFF_MINOR &&
 			dig_version[1] >= ADC5_HW_SETTLE_DIFF_MAJOR) ||
 			adc->data->info == &adc7_info)
-			ret = adc5_hw_settle_time_from_dt(value,
-							data->hw_settle_2);
+			ret = qcom_adc5_hw_settle_time_from_dt(value, data->hw_settle_2);
 		else
-			ret = adc5_hw_settle_time_from_dt(value,
-							data->hw_settle_1);
+			ret = qcom_adc5_hw_settle_time_from_dt(value, data->hw_settle_1);
 
 		if (ret < 0) {
 			dev_err(dev, "%02x invalid hw-settle-time %d us\n",
@@ -777,7 +714,7 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
 
 	ret = of_property_read_u32(node, "qcom,avg-samples", &value);
 	if (!ret) {
-		ret = adc5_avg_samples_from_dt(value);
+		ret = qcom_adc5_avg_samples_from_dt(value);
 		if (ret < 0) {
 			dev_err(dev, "%02x invalid avg-samples %d\n",
 				chan, value);
diff --git a/drivers/iio/adc/qcom-vadc-common.c b/drivers/iio/adc/qcom-vadc-common.c
index 5113aaa6ba67..d11f3343ad52 100644
--- a/drivers/iio/adc/qcom-vadc-common.c
+++ b/drivers/iio/adc/qcom-vadc-common.c
@@ -278,6 +278,18 @@ static const struct vadc_map_pt adcmap7_100k[] = {
 	{ 2420, 130048 }
 };
 
+static const struct vadc_prescale_ratio adc5_prescale_ratios[] = {
+	{.num =  1, .den =  1},
+	{.num =  1, .den =  3},
+	{.num =  1, .den =  4},
+	{.num =  1, .den =  6},
+	{.num =  1, .den = 20},
+	{.num =  1, .den =  8},
+	{.num = 10, .den = 81},
+	{.num =  1, .den = 10},
+	{.num =  1, .den = 16}
+};
+
 static int qcom_vadc_scale_hw_calib_volt(
 				const struct vadc_prescale_ratio *prescale,
 				const struct adc5_data *data,
@@ -647,10 +659,12 @@ int qcom_vadc_scale(enum vadc_scale_fn_type scaletype,
 EXPORT_SYMBOL(qcom_vadc_scale);
 
 int qcom_adc5_hw_scale(enum vadc_scale_fn_type scaletype,
-		    const struct vadc_prescale_ratio *prescale,
+		    unsigned int prescale_ratio,
 		    const struct adc5_data *data,
 		    u16 adc_code, int *result)
 {
+	const struct vadc_prescale_ratio *prescale = &adc5_prescale_ratios[prescale_ratio];
+
 	if (!(scaletype >= SCALE_HW_CALIB_DEFAULT &&
 		scaletype < SCALE_HW_CALIB_INVALID)) {
 		pr_err("Invalid scale type %d\n", scaletype);
@@ -662,6 +676,58 @@ int qcom_adc5_hw_scale(enum vadc_scale_fn_type scaletype,
 }
 EXPORT_SYMBOL(qcom_adc5_hw_scale);
 
+int qcom_adc5_prescaling_from_dt(u32 num, u32 den)
+{
+	unsigned int pre;
+
+	for (pre = 0; pre < ARRAY_SIZE(adc5_prescale_ratios); pre++)
+		if (adc5_prescale_ratios[pre].num == num &&
+		    adc5_prescale_ratios[pre].den == den)
+			break;
+
+	if (pre == ARRAY_SIZE(adc5_prescale_ratios))
+		return -EINVAL;
+
+	return pre;
+}
+EXPORT_SYMBOL(qcom_adc5_prescaling_from_dt);
+
+int qcom_adc5_hw_settle_time_from_dt(u32 value,
+				     const unsigned int *hw_settle)
+{
+	unsigned int i;
+
+	for (i = 0; i < VADC_HW_SETTLE_SAMPLES_MAX; i++) {
+		if (value == hw_settle[i])
+			return i;
+	}
+
+	return -EINVAL;
+}
+EXPORT_SYMBOL(qcom_adc5_hw_settle_time_from_dt);
+
+int qcom_adc5_avg_samples_from_dt(u32 value)
+{
+	if (!is_power_of_2(value) || value > ADC5_AVG_SAMPLES_MAX)
+		return -EINVAL;
+
+	return __ffs(value);
+}
+EXPORT_SYMBOL(qcom_adc5_avg_samples_from_dt);
+
+int qcom_adc5_decimation_from_dt(u32 value, const unsigned int *decimation)
+{
+	unsigned int i;
+
+	for (i = 0; i < ADC5_DECIMATION_SAMPLES_MAX; i++) {
+		if (value == decimation[i])
+			return i;
+	}
+
+	return -EINVAL;
+}
+EXPORT_SYMBOL(qcom_adc5_decimation_from_dt);
+
 int qcom_vadc_decimation_from_dt(u32 value)
 {
 	if (!is_power_of_2(value) || value < VADC_DECIMATION_MIN ||
diff --git a/drivers/iio/adc/qcom-vadc-common.h b/drivers/iio/adc/qcom-vadc-common.h
index 17b2fc4d8bf2..7e5f6428e311 100644
--- a/drivers/iio/adc/qcom-vadc-common.h
+++ b/drivers/iio/adc/qcom-vadc-common.h
@@ -168,10 +168,18 @@ struct qcom_adc5_scale_type {
 };
 
 int qcom_adc5_hw_scale(enum vadc_scale_fn_type scaletype,
-		    const struct vadc_prescale_ratio *prescale,
+		    unsigned int prescale_ratio,
 		    const struct adc5_data *data,
 		    u16 adc_code, int *result_mdec);
 
+int qcom_adc5_prescaling_from_dt(u32 num, u32 den);
+
+int qcom_adc5_hw_settle_time_from_dt(u32 value, const unsigned int *hw_settle);
+
+int qcom_adc5_avg_samples_from_dt(u32 value);
+
+int qcom_adc5_decimation_from_dt(u32 value, const unsigned int *decimation);
+
 int qcom_vadc_decimation_from_dt(u32 value);
 
 #endif /* QCOM_VADC_COMMON_H */
-- 
2.28.0


^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v8 04/11] iio: adc: qcom-vadc-common: use fixp_linear_interpolate
  2020-10-09 15:44 [PATCH v8 00/11] qcom: pm8150: add support for thermal monitoring Dmitry Baryshkov
                   ` (2 preceding siblings ...)
  2020-10-09 15:44 ` [PATCH v8 03/11] iio: adc: qcom-vadc: move several adc5 functions to common file Dmitry Baryshkov
@ 2020-10-09 15:44 ` Dmitry Baryshkov
  2020-10-09 15:44 ` [PATCH v8 05/11] iio: adc: move qcom-vadc-common.h to include dir Dmitry Baryshkov
                   ` (6 subsequent siblings)
  10 siblings, 0 replies; 13+ messages in thread
From: Dmitry Baryshkov @ 2020-10-09 15:44 UTC (permalink / raw)
  To: Andy Gross, Bjorn Andersson, Rob Herring, Zhang Rui,
	Daniel Lezcano, Amit Kucheria, Jonathan Cameron, Hartmut Knaack,
	Lars-Peter Clausen, Peter Meerwald-Stadler
  Cc: linux-arm-msm, linux-pm, devicetree, linux-iio,
	Manivannan Sadhasivam, Jishnu Prakash, Jonathan Cameron

Use new function fixp_linear_interpolate() instead of hand-coding the
linear interpolation.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
---
 drivers/iio/adc/qcom-vadc-common.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/iio/adc/qcom-vadc-common.c b/drivers/iio/adc/qcom-vadc-common.c
index d11f3343ad52..40d77b3af1bb 100644
--- a/drivers/iio/adc/qcom-vadc-common.c
+++ b/drivers/iio/adc/qcom-vadc-common.c
@@ -2,6 +2,7 @@
 #include <linux/bug.h>
 #include <linux/kernel.h>
 #include <linux/bitops.h>
+#include <linux/fixp-arith.h>
 #include <linux/math64.h>
 #include <linux/log2.h>
 #include <linux/err.h>
@@ -368,10 +369,9 @@ static int qcom_vadc_map_voltage_temp(const struct vadc_map_pt *pts,
 	} else {
 		/* result is between search_index and search_index-1 */
 		/* interpolate linearly */
-		*output = (((s32)((pts[i].y - pts[i - 1].y) *
-			(input - pts[i - 1].x)) /
-			(pts[i].x - pts[i - 1].x)) +
-			pts[i - 1].y);
+		*output = fixp_linear_interpolate(pts[i - 1].x, pts[i - 1].y,
+						  pts[i].x, pts[i].y,
+						  input);
 	}
 
 	return 0;
-- 
2.28.0


^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v8 05/11] iio: adc: move qcom-vadc-common.h to include dir
  2020-10-09 15:44 [PATCH v8 00/11] qcom: pm8150: add support for thermal monitoring Dmitry Baryshkov
                   ` (3 preceding siblings ...)
  2020-10-09 15:44 ` [PATCH v8 04/11] iio: adc: qcom-vadc-common: use fixp_linear_interpolate Dmitry Baryshkov
@ 2020-10-09 15:44 ` Dmitry Baryshkov
  2020-10-09 15:44 ` [PATCH v8 06/11] iio: adc: qcom-spmi-adc5: use of_device_get_match_data Dmitry Baryshkov
                   ` (5 subsequent siblings)
  10 siblings, 0 replies; 13+ messages in thread
From: Dmitry Baryshkov @ 2020-10-09 15:44 UTC (permalink / raw)
  To: Andy Gross, Bjorn Andersson, Rob Herring, Zhang Rui,
	Daniel Lezcano, Amit Kucheria, Jonathan Cameron, Hartmut Knaack,
	Lars-Peter Clausen, Peter Meerwald-Stadler
  Cc: linux-arm-msm, linux-pm, devicetree, linux-iio,
	Manivannan Sadhasivam, Jishnu Prakash

qcom-vadc-common module will be used by ADC thermal monitoring driver,
so move it to global include dir.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 drivers/iio/adc/qcom-pm8xxx-xoadc.c                   | 3 +--
 drivers/iio/adc/qcom-spmi-adc5.c                      | 2 +-
 drivers/iio/adc/qcom-spmi-vadc.c                      | 3 +--
 drivers/iio/adc/qcom-vadc-common.c                    | 3 +--
 {drivers => include/linux}/iio/adc/qcom-vadc-common.h | 2 ++
 5 files changed, 6 insertions(+), 7 deletions(-)
 rename {drivers => include/linux}/iio/adc/qcom-vadc-common.h (99%)

diff --git a/drivers/iio/adc/qcom-pm8xxx-xoadc.c b/drivers/iio/adc/qcom-pm8xxx-xoadc.c
index 7e108da7d255..0610bf254771 100644
--- a/drivers/iio/adc/qcom-pm8xxx-xoadc.c
+++ b/drivers/iio/adc/qcom-pm8xxx-xoadc.c
@@ -10,6 +10,7 @@
  * Author: Linus Walleij <linus.walleij@linaro.org>
  */
 
+#include <linux/iio/adc/qcom-vadc-common.h>
 #include <linux/iio/iio.h>
 #include <linux/iio/sysfs.h>
 #include <linux/module.h>
@@ -21,8 +22,6 @@
 #include <linux/interrupt.h>
 #include <linux/regulator/consumer.h>
 
-#include "qcom-vadc-common.h"
-
 /*
  * Definitions for the "user processor" registers lifted from the v3.4
  * Qualcomm tree. Their kernel has two out-of-tree drivers for the ADC:
diff --git a/drivers/iio/adc/qcom-spmi-adc5.c b/drivers/iio/adc/qcom-spmi-adc5.c
index c2da8f068b87..b10a0fcf09dc 100644
--- a/drivers/iio/adc/qcom-spmi-adc5.c
+++ b/drivers/iio/adc/qcom-spmi-adc5.c
@@ -7,6 +7,7 @@
 #include <linux/completion.h>
 #include <linux/delay.h>
 #include <linux/err.h>
+#include <linux/iio/adc/qcom-vadc-common.h>
 #include <linux/iio/iio.h>
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
@@ -19,7 +20,6 @@
 #include <linux/slab.h>
 
 #include <dt-bindings/iio/qcom,spmi-vadc.h>
-#include "qcom-vadc-common.h"
 
 #define ADC5_USR_REVISION1			0x0
 #define ADC5_USR_STATUS1			0x8
diff --git a/drivers/iio/adc/qcom-spmi-vadc.c b/drivers/iio/adc/qcom-spmi-vadc.c
index b0388f8a69f4..05ff948372b3 100644
--- a/drivers/iio/adc/qcom-spmi-vadc.c
+++ b/drivers/iio/adc/qcom-spmi-vadc.c
@@ -7,6 +7,7 @@
 #include <linux/completion.h>
 #include <linux/delay.h>
 #include <linux/err.h>
+#include <linux/iio/adc/qcom-vadc-common.h>
 #include <linux/iio/iio.h>
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
@@ -20,8 +21,6 @@
 
 #include <dt-bindings/iio/qcom,spmi-vadc.h>
 
-#include "qcom-vadc-common.h"
-
 /* VADC register and bit definitions */
 #define VADC_REVISION2				0x1
 #define VADC_REVISION2_SUPPORTED_VADC		1
diff --git a/drivers/iio/adc/qcom-vadc-common.c b/drivers/iio/adc/qcom-vadc-common.c
index 40d77b3af1bb..ee94774b72e6 100644
--- a/drivers/iio/adc/qcom-vadc-common.c
+++ b/drivers/iio/adc/qcom-vadc-common.c
@@ -3,14 +3,13 @@
 #include <linux/kernel.h>
 #include <linux/bitops.h>
 #include <linux/fixp-arith.h>
+#include <linux/iio/adc/qcom-vadc-common.h>
 #include <linux/math64.h>
 #include <linux/log2.h>
 #include <linux/err.h>
 #include <linux/module.h>
 #include <linux/units.h>
 
-#include "qcom-vadc-common.h"
-
 /* Voltage to temperature */
 static const struct vadc_map_pt adcmap_100k_104ef_104fb[] = {
 	{1758,	-40},
diff --git a/drivers/iio/adc/qcom-vadc-common.h b/include/linux/iio/adc/qcom-vadc-common.h
similarity index 99%
rename from drivers/iio/adc/qcom-vadc-common.h
rename to include/linux/iio/adc/qcom-vadc-common.h
index 7e5f6428e311..03a9119edc71 100644
--- a/drivers/iio/adc/qcom-vadc-common.h
+++ b/include/linux/iio/adc/qcom-vadc-common.h
@@ -6,6 +6,8 @@
 #ifndef QCOM_VADC_COMMON_H
 #define QCOM_VADC_COMMON_H
 
+#include <linux/types.h>
+
 #define VADC_CONV_TIME_MIN_US			2000
 #define VADC_CONV_TIME_MAX_US			2100
 
-- 
2.28.0


^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v8 06/11] iio: adc: qcom-spmi-adc5: use of_device_get_match_data
  2020-10-09 15:44 [PATCH v8 00/11] qcom: pm8150: add support for thermal monitoring Dmitry Baryshkov
                   ` (4 preceding siblings ...)
  2020-10-09 15:44 ` [PATCH v8 05/11] iio: adc: move qcom-vadc-common.h to include dir Dmitry Baryshkov
@ 2020-10-09 15:44 ` Dmitry Baryshkov
  2020-10-09 15:44 ` [PATCH v8 07/11] iio: provide of_iio_channel_get_by_name() and devm_ version it Dmitry Baryshkov
                   ` (4 subsequent siblings)
  10 siblings, 0 replies; 13+ messages in thread
From: Dmitry Baryshkov @ 2020-10-09 15:44 UTC (permalink / raw)
  To: Andy Gross, Bjorn Andersson, Rob Herring, Zhang Rui,
	Daniel Lezcano, Amit Kucheria, Jonathan Cameron, Hartmut Knaack,
	Lars-Peter Clausen, Peter Meerwald-Stadler
  Cc: linux-arm-msm, linux-pm, devicetree, linux-iio,
	Manivannan Sadhasivam, Jishnu Prakash, Jonathan Cameron

Use of_device_get_match_data() instead of hand-coding it manually.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 drivers/iio/adc/qcom-spmi-adc5.c | 18 +++++++-----------
 1 file changed, 7 insertions(+), 11 deletions(-)

diff --git a/drivers/iio/adc/qcom-spmi-adc5.c b/drivers/iio/adc/qcom-spmi-adc5.c
index b10a0fcf09dc..87438d1e5c0b 100644
--- a/drivers/iio/adc/qcom-spmi-adc5.c
+++ b/drivers/iio/adc/qcom-spmi-adc5.c
@@ -15,6 +15,7 @@
 #include <linux/math64.h>
 #include <linux/module.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
 #include <linux/slab.h>
@@ -807,8 +808,6 @@ static int adc5_get_dt_data(struct adc5_chip *adc, struct device_node *node)
 	struct adc5_channel_prop prop, *chan_props;
 	struct device_node *child;
 	unsigned int index = 0;
-	const struct of_device_id *id;
-	const struct adc5_data *data;
 	int ret;
 
 	adc->nchannels = of_get_available_child_count(node);
@@ -827,24 +826,21 @@ static int adc5_get_dt_data(struct adc5_chip *adc, struct device_node *node)
 
 	chan_props = adc->chan_props;
 	iio_chan = adc->iio_chans;
-	id = of_match_node(adc5_match_table, node);
-	if (id)
-		data = id->data;
-	else
-		data = &adc5_data_pmic;
-	adc->data = data;
+	adc->data = of_device_get_match_data(adc->dev);
+	if (!adc->data)
+		adc->data = &adc5_data_pmic;
 
 	for_each_available_child_of_node(node, child) {
-		ret = adc5_get_dt_channel_data(adc, &prop, child, data);
+		ret = adc5_get_dt_channel_data(adc, &prop, child, adc->data);
 		if (ret) {
 			of_node_put(child);
 			return ret;
 		}
 
 		prop.scale_fn_type =
-			data->adc_chans[prop.channel].scale_fn_type;
+			adc->data->adc_chans[prop.channel].scale_fn_type;
 		*chan_props = prop;
-		adc_chan = &data->adc_chans[prop.channel];
+		adc_chan = &adc->data->adc_chans[prop.channel];
 
 		iio_chan->channel = prop.channel;
 		iio_chan->datasheet_name = prop.datasheet_name;
-- 
2.28.0


^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v8 07/11] iio: provide of_iio_channel_get_by_name() and devm_ version it
  2020-10-09 15:44 [PATCH v8 00/11] qcom: pm8150: add support for thermal monitoring Dmitry Baryshkov
                   ` (5 preceding siblings ...)
  2020-10-09 15:44 ` [PATCH v8 06/11] iio: adc: qcom-spmi-adc5: use of_device_get_match_data Dmitry Baryshkov
@ 2020-10-09 15:44 ` Dmitry Baryshkov
  2020-10-09 15:44 ` [PATCH v8 08/11] thermal: qcom: add support for adc-tm5 PMIC thermal monitor Dmitry Baryshkov
                   ` (3 subsequent siblings)
  10 siblings, 0 replies; 13+ messages in thread
From: Dmitry Baryshkov @ 2020-10-09 15:44 UTC (permalink / raw)
  To: Andy Gross, Bjorn Andersson, Rob Herring, Zhang Rui,
	Daniel Lezcano, Amit Kucheria, Jonathan Cameron, Hartmut Knaack,
	Lars-Peter Clausen, Peter Meerwald-Stadler
  Cc: linux-arm-msm, linux-pm, devicetree, linux-iio,
	Manivannan Sadhasivam, Jishnu Prakash, Jonathan Cameron

There might be cases when the IIO channel is attached to the device
subnode instead of being attached to the main device node. Allow drivers
to query IIO channels by using device tree nodes.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
---
 drivers/iio/inkern.c         | 34 ++++++++++++++++++++++++++--------
 include/linux/iio/consumer.h | 36 ++++++++++++++++++++++++++++++++++++
 2 files changed, 62 insertions(+), 8 deletions(-)

diff --git a/drivers/iio/inkern.c b/drivers/iio/inkern.c
index ede99e0d5371..8ff0ac472de3 100644
--- a/drivers/iio/inkern.c
+++ b/drivers/iio/inkern.c
@@ -180,8 +180,8 @@ static struct iio_channel *of_iio_channel_get(struct device_node *np, int index)
 	return ERR_PTR(err);
 }
 
-static struct iio_channel *of_iio_channel_get_by_name(struct device_node *np,
-						      const char *name)
+struct iio_channel *of_iio_channel_get_by_name(struct device_node *np,
+					       const char *name)
 {
 	struct iio_channel *chan = NULL;
 
@@ -219,6 +219,7 @@ static struct iio_channel *of_iio_channel_get_by_name(struct device_node *np,
 
 	return chan;
 }
+EXPORT_SYMBOL_GPL(of_iio_channel_get_by_name);
 
 static struct iio_channel *of_iio_channel_get_all(struct device *dev)
 {
@@ -261,12 +262,6 @@ static struct iio_channel *of_iio_channel_get_all(struct device *dev)
 
 #else /* CONFIG_OF */
 
-static inline struct iio_channel *
-of_iio_channel_get_by_name(struct device_node *np, const char *name)
-{
-	return NULL;
-}
-
 static inline struct iio_channel *of_iio_channel_get_all(struct device *dev)
 {
 	return NULL;
@@ -382,6 +377,29 @@ struct iio_channel *devm_iio_channel_get(struct device *dev,
 }
 EXPORT_SYMBOL_GPL(devm_iio_channel_get);
 
+struct iio_channel *devm_of_iio_channel_get_by_name(struct device *dev,
+						    struct device_node *np,
+						    const char *channel_name)
+{
+	struct iio_channel **ptr, *channel;
+
+	ptr = devres_alloc(devm_iio_channel_free, sizeof(*ptr), GFP_KERNEL);
+	if (!ptr)
+		return ERR_PTR(-ENOMEM);
+
+	channel = of_iio_channel_get_by_name(np, channel_name);
+	if (IS_ERR(channel)) {
+		devres_free(ptr);
+		return channel;
+	}
+
+	*ptr = channel;
+	devres_add(dev, ptr);
+
+	return channel;
+}
+EXPORT_SYMBOL_GPL(devm_of_iio_channel_get_by_name);
+
 struct iio_channel *iio_channel_get_all(struct device *dev)
 {
 	const char *name;
diff --git a/include/linux/iio/consumer.h b/include/linux/iio/consumer.h
index c4118dcb8e05..0a90ba8fa1bb 100644
--- a/include/linux/iio/consumer.h
+++ b/include/linux/iio/consumer.h
@@ -13,6 +13,7 @@
 struct iio_dev;
 struct iio_chan_spec;
 struct device;
+struct device_node;
 
 /**
  * struct iio_channel - everything needed for a consumer to use a channel
@@ -97,6 +98,41 @@ void iio_channel_release_all(struct iio_channel *chan);
  */
 struct iio_channel *devm_iio_channel_get_all(struct device *dev);
 
+/**
+ * of_iio_channel_get_by_name() - get description of all that is needed to access channel.
+ * @np:			Pointer to consumer device tree node
+ * @consumer_channel:	Unique name to identify the channel on the consumer
+ *			side. This typically describes the channels use within
+ *			the consumer. E.g. 'battery_voltage'
+ */
+#ifdef CONFIG_OF
+struct iio_channel *of_iio_channel_get_by_name(struct device_node *np, const char *name);
+#else
+static inline struct iio_channel *
+of_iio_channel_get_by_name(struct device_node *np, const char *name)
+{
+	return NULL;
+}
+#endif
+
+/**
+ * devm_of_iio_channel_get_by_name() - Resource managed version of of_iio_channel_get_by_name().
+ * @dev:		Pointer to consumer device.
+ * @np:			Pointer to consumer device tree node
+ * @consumer_channel:	Unique name to identify the channel on the consumer
+ *			side. This typically describes the channels use within
+ *			the consumer. E.g. 'battery_voltage'
+ *
+ * Returns a pointer to negative errno if it is not able to get the iio channel
+ * otherwise returns valid pointer for iio channel.
+ *
+ * The allocated iio channel is automatically released when the device is
+ * unbound.
+ */
+struct iio_channel *devm_of_iio_channel_get_by_name(struct device *dev,
+						    struct device_node *np,
+						    const char *consumer_channel);
+
 struct iio_cb_buffer;
 /**
  * iio_channel_get_all_cb() - register callback for triggered capture
-- 
2.28.0


^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v8 08/11] thermal: qcom: add support for adc-tm5 PMIC thermal monitor
  2020-10-09 15:44 [PATCH v8 00/11] qcom: pm8150: add support for thermal monitoring Dmitry Baryshkov
                   ` (6 preceding siblings ...)
  2020-10-09 15:44 ` [PATCH v8 07/11] iio: provide of_iio_channel_get_by_name() and devm_ version it Dmitry Baryshkov
@ 2020-10-09 15:44 ` Dmitry Baryshkov
  2020-10-14 16:32   ` mka
  2020-10-09 15:44 ` [PATCH v8 09/11] arm64: dts: qcom: pm8150x: add definitions for adc-tm5 part Dmitry Baryshkov
                   ` (2 subsequent siblings)
  10 siblings, 1 reply; 13+ messages in thread
From: Dmitry Baryshkov @ 2020-10-09 15:44 UTC (permalink / raw)
  To: Andy Gross, Bjorn Andersson, Rob Herring, Zhang Rui,
	Daniel Lezcano, Amit Kucheria, Jonathan Cameron, Hartmut Knaack,
	Lars-Peter Clausen, Peter Meerwald-Stadler
  Cc: linux-arm-msm, linux-pm, devicetree, linux-iio,
	Manivannan Sadhasivam, Jishnu Prakash

Add support for Thermal Monitoring part of PMIC5. This part is closely
coupled with ADC, using it's channels directly. ADC-TM support
generating interrupts on ADC value crossing low or high voltage bounds,
which is used to support thermal trip points.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 drivers/iio/adc/qcom-vadc-common.c       |  62 +++
 drivers/thermal/qcom/Kconfig             |  11 +
 drivers/thermal/qcom/Makefile            |   1 +
 drivers/thermal/qcom/qcom-spmi-adc-tm5.c | 619 +++++++++++++++++++++++
 include/linux/iio/adc/qcom-vadc-common.h |   3 +
 5 files changed, 696 insertions(+)
 create mode 100644 drivers/thermal/qcom/qcom-spmi-adc-tm5.c

diff --git a/drivers/iio/adc/qcom-vadc-common.c b/drivers/iio/adc/qcom-vadc-common.c
index ee94774b72e6..8ceefb079712 100644
--- a/drivers/iio/adc/qcom-vadc-common.c
+++ b/drivers/iio/adc/qcom-vadc-common.c
@@ -376,6 +376,42 @@ static int qcom_vadc_map_voltage_temp(const struct vadc_map_pt *pts,
 	return 0;
 }
 
+static s32 qcom_vadc_map_temp_voltage(const struct vadc_map_pt *pts,
+				      u32 tablesize, int input)
+{
+	bool descending = 1;
+	u32 i = 0;
+
+	/* Check if table is descending or ascending */
+	if (tablesize > 1) {
+		if (pts[0].y < pts[1].y)
+			descending = 0;
+	}
+
+	while (i < tablesize) {
+		if (descending && pts[i].y < input) {
+			/* table entry is less than measured*/
+			 /* value and table is descending, stop */
+			break;
+		} else if ((!descending) && pts[i].y > input) {
+			/* table entry is greater than measured*/
+			/*value and table is ascending, stop */
+			break;
+		}
+		i++;
+	}
+
+	if (i == 0)
+		return pts[0].x;
+	if (i == tablesize)
+		return pts[tablesize - 1].x;
+
+	/* result is between search_index and search_index-1 */
+	/* interpolate linearly */
+	return fixp_linear_interpolate(pts[i - 1].y, pts[i - 1].x,
+			pts[i].y, pts[i].x, input);
+}
+
 static void qcom_vadc_scale_calib(const struct vadc_linear_graph *calib_graph,
 				  u16 adc_code,
 				  bool absolute,
@@ -473,6 +509,19 @@ static int qcom_vadc_scale_chg_temp(const struct vadc_linear_graph *calib_graph,
 	return 0;
 }
 
+static u16 qcom_vadc_scale_voltage_code(int voltage,
+					const struct vadc_prescale_ratio *prescale,
+					const u32 full_scale_code_volt,
+					unsigned int factor)
+{
+	s64 volt = voltage, adc_vdd_ref_mv = 1875;
+
+	volt *= prescale->num * factor * full_scale_code_volt;
+	volt = div64_s64(volt, (s64)prescale->den * adc_vdd_ref_mv * 1000);
+
+	return volt;
+}
+
 static int qcom_vadc_scale_code_voltage_factor(u16 adc_code,
 				const struct vadc_prescale_ratio *prescale,
 				const struct adc5_data *data,
@@ -657,6 +706,19 @@ int qcom_vadc_scale(enum vadc_scale_fn_type scaletype,
 }
 EXPORT_SYMBOL(qcom_vadc_scale);
 
+u16 qcom_adc_tm5_temp_volt_scale(unsigned int prescale_ratio,
+				 u32 full_scale_code_volt, int temp)
+{
+	const struct vadc_prescale_ratio *prescale = &adc5_prescale_ratios[prescale_ratio];
+	s32 voltage;
+
+	voltage = qcom_vadc_map_temp_voltage(adcmap_100k_104ef_104fb_1875_vref,
+					     ARRAY_SIZE(adcmap_100k_104ef_104fb_1875_vref),
+					     temp);
+	return qcom_vadc_scale_voltage_code(voltage, prescale, full_scale_code_volt, 1000);
+}
+EXPORT_SYMBOL(qcom_adc_tm5_temp_volt_scale);
+
 int qcom_adc5_hw_scale(enum vadc_scale_fn_type scaletype,
 		    unsigned int prescale_ratio,
 		    const struct adc5_data *data,
diff --git a/drivers/thermal/qcom/Kconfig b/drivers/thermal/qcom/Kconfig
index aa9c1d80fae4..8d5ac2df26dc 100644
--- a/drivers/thermal/qcom/Kconfig
+++ b/drivers/thermal/qcom/Kconfig
@@ -10,6 +10,17 @@ config QCOM_TSENS
 	  Also able to set threshold temperature for both hot and cold and update
 	  when a threshold is reached.
 
+config QCOM_SPMI_ADC_TM5
+	tristate "Qualcomm SPMI PMIC Thermal Monitor ADC5"
+	depends on OF && SPMI && IIO
+	select REGMAP_SPMI
+	select QCOM_VADC_COMMON
+	help
+	  This enables the thermal driver for the ADC thermal monitoring
+	  device. It shows up as a thermal zone with multiple trip points.
+	  Thermal client sets threshold temperature for both warm and cool and
+	  gets updated when a threshold is reached.
+
 config QCOM_SPMI_TEMP_ALARM
 	tristate "Qualcomm SPMI PMIC Temperature Alarm"
 	depends on OF && SPMI && IIO
diff --git a/drivers/thermal/qcom/Makefile b/drivers/thermal/qcom/Makefile
index ec86eef7f6a6..252ea7d9da0b 100644
--- a/drivers/thermal/qcom/Makefile
+++ b/drivers/thermal/qcom/Makefile
@@ -3,4 +3,5 @@ obj-$(CONFIG_QCOM_TSENS)	+= qcom_tsens.o
 
 qcom_tsens-y			+= tsens.o tsens-v2.o tsens-v1.o tsens-v0_1.o \
 				   tsens-8960.o
+obj-$(CONFIG_QCOM_SPMI_ADC_TM5)	+= qcom-spmi-adc-tm5.o
 obj-$(CONFIG_QCOM_SPMI_TEMP_ALARM)	+= qcom-spmi-temp-alarm.o
diff --git a/drivers/thermal/qcom/qcom-spmi-adc-tm5.c b/drivers/thermal/qcom/qcom-spmi-adc-tm5.c
new file mode 100644
index 000000000000..9e4d5ae5fe33
--- /dev/null
+++ b/drivers/thermal/qcom/qcom-spmi-adc-tm5.c
@@ -0,0 +1,619 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2012-2020, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020 Linaro Limited
+ */
+
+#include <linux/bitfield.h>
+#include <linux/iio/adc/qcom-vadc-common.h>
+#include <linux/iio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/thermal.h>
+
+#define ADC5_MAX_CHANNEL                        0xc0
+#define ADC_TM5_NUM_CHANNELS		8
+
+#define ADC_TM5_STATUS_LOW			0x0a
+
+#define ADC_TM5_STATUS_HIGH			0x0b
+
+#define ADC_TM5_NUM_BTM				0x0f
+
+#define ADC_TM5_ADC_DIG_PARAM			0x42
+
+#define ADC_TM5_FAST_AVG_CTL			(ADC_TM5_ADC_DIG_PARAM + 1)
+#define ADC_TM5_FAST_AVG_EN				BIT(7)
+
+#define ADC_TM5_MEAS_INTERVAL_CTL		(ADC_TM5_ADC_DIG_PARAM + 2)
+#define ADC_TM5_TIMER1					3 /* 3.9ms */
+
+#define ADC_TM5_MEAS_INTERVAL_CTL2		(ADC_TM5_ADC_DIG_PARAM + 3)
+#define ADC_TM5_MEAS_INTERVAL_CTL2_MASK			0xf0
+#define ADC_TM5_TIMER2					10 /* 1 second */
+#define ADC_TM5_MEAS_INTERVAL_CTL3_MASK			0xf
+#define ADC_TM5_TIMER3					4 /* 4 second */
+
+#define ADC_TM_EN_CTL1				0x46
+#define ADC_TM_EN					BIT(7)
+#define ADC_TM_CONV_REQ				0x47
+#define ADC_TM_CONV_REQ_EN				BIT(7)
+
+#define ADC_TM5_M_CHAN_BASE			0x60
+
+#define ADC_TM5_M_ADC_CH_SEL_CTL(n)		(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 0)
+#define ADC_TM5_M_LOW_THR0(n)			(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 1)
+#define ADC_TM5_M_LOW_THR1(n)			(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 2)
+#define ADC_TM5_M_HIGH_THR0(n)			(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 3)
+#define ADC_TM5_M_HIGH_THR1(n)			(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 4)
+#define ADC_TM5_M_MEAS_INTERVAL_CTL(n)		(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 5)
+#define ADC_TM5_M_CTL(n)			(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 6)
+#define ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK		0xf
+#define ADC_TM5_M_CTL_CAL_SEL_MASK			0x30
+#define ADC_TM5_M_CTL_CAL_VAL				0x40
+#define ADC_TM5_M_EN(n)				(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 7)
+#define ADC_TM5_M_MEAS_EN				BIT(7)
+#define ADC_TM5_M_HIGH_THR_INT_EN			BIT(1)
+#define ADC_TM5_M_LOW_THR_INT_EN			BIT(0)
+
+enum adc5_timer_select {
+	ADC5_TIMER_SEL_1 = 0,
+	ADC5_TIMER_SEL_2,
+	ADC5_TIMER_SEL_3,
+	ADC5_TIMER_SEL_NONE,
+};
+
+struct adc_tm5_data {
+	const u32	full_scale_code_volt;
+	unsigned int	*decimation;
+	unsigned int	*hw_settle;
+};
+
+enum adc_tm5_cal_method {
+	ADC_TM5_NO_CAL = 0,
+	ADC_TM5_RATIOMETRIC_CAL,
+	ADC_TM5_ABSOLUTE_CAL
+};
+
+struct adc_tm5_chip;
+
+/**
+ * struct adc_tm5_channel - ADC Thermal Monitoring channel data.
+ * @channel: channel number.
+ * @adc_channel: corresponding ADC channel number.
+ * @cal_method: calibration method.
+ * @prescale: channel scaling performed on the input signal.
+ * @hw_settle_time: the time between AMUX being configured and the
+ *	start of conversion.
+ * @iio: IIO channel instance used by this channel.
+ * @chip: ADC TM chip instance.
+ * @tzd: thermal zone device used by this channel.
+ */
+struct adc_tm5_channel {
+	unsigned int		channel;
+	unsigned int		adc_channel;
+	enum adc_tm5_cal_method	cal_method;
+	unsigned int		prescale;
+	unsigned int		hw_settle_time;
+	struct iio_channel	*iio;
+	struct adc_tm5_chip	*chip;
+	struct thermal_zone_device *tzd;
+};
+
+/**
+ * struct adc_tm5_chip - ADC Thermal Monitoring properties
+ * @regmap: SPMI ADC5 Thermal Monitoring  peripheral register map field.
+ * @dev: SPMI ADC5 device.
+ * @data: software configuration data.
+ * @channels: array of ADC TM channel data.
+ * @nchannels: amount of channels defined/allocated
+ * @decimation: sampling rate supported for the channel.
+ * @avg_samples: ability to provide single result from the ADC
+ *	that is an average of multiple measurements.
+ * @base: base address of TM registers.
+ */
+struct adc_tm5_chip {
+	struct regmap		*regmap;
+	struct device		*dev;
+	const struct adc_tm5_data	*data;
+	struct adc_tm5_channel	*channels;
+	unsigned int		nchannels;
+	unsigned int		decimation;
+	unsigned int		avg_samples;
+	u16			base;
+};
+
+static const struct adc_tm5_data adc_tm5_data_pmic = {
+	.full_scale_code_volt = 0x70e4,
+	.decimation = (unsigned int []) { 250, 420, 840 },
+	.hw_settle = (unsigned int []) { 15, 100, 200, 300, 400, 500, 600, 700,
+					 1000, 2000, 4000, 8000, 16000, 32000,
+					 64000, 128000 },
+};
+
+static int adc_tm5_read(struct adc_tm5_chip *adc_tm, u16 offset, u8 *data, int len)
+{
+	return regmap_bulk_read(adc_tm->regmap, adc_tm->base + offset, data, len);
+}
+
+static int adc_tm5_write(struct adc_tm5_chip *adc_tm, u16 offset, u8 *data, int len)
+{
+	return regmap_bulk_write(adc_tm->regmap, adc_tm->base + offset, data, len);
+}
+
+static int adc_tm5_reg_update(struct adc_tm5_chip *adc_tm, u16 offset, u8 mask, u8 val)
+{
+	return regmap_write_bits(adc_tm->regmap, adc_tm->base + offset, mask, val);
+}
+
+static irqreturn_t adc_tm5_isr(int irq, void *data)
+{
+	struct adc_tm5_chip *chip = data;
+	u8 status_low, status_high, ctl;
+	int ret = 0, i = 0;
+
+	ret = adc_tm5_read(chip, ADC_TM5_STATUS_LOW, &status_low, sizeof(status_low));
+	if (unlikely(ret)) {
+		dev_err(chip->dev, "read status low failed with %d\n", ret);
+		return IRQ_HANDLED;
+	}
+
+	ret = adc_tm5_read(chip, ADC_TM5_STATUS_HIGH, &status_high, sizeof(status_high));
+	if (unlikely(ret)) {
+		dev_err(chip->dev, "read status high failed with %d\n", ret);
+		return IRQ_HANDLED;
+	}
+
+	for (i = 0; i < chip->nchannels; i++) {
+		bool upper_set = false, lower_set = false;
+		unsigned int ch = chip->channels[i].channel;
+
+		if (!chip->channels[i].tzd) {
+			dev_err_once(chip->dev, "thermal device not found\n");
+			continue;
+		}
+
+		ret = adc_tm5_read(chip, ADC_TM5_M_EN(ch), &ctl, sizeof(ctl));
+		if (unlikely(ret)) {
+			dev_err(chip->dev, "ctl read failed with %d\n", ret);
+			continue;
+		}
+
+		if (!(ctl & ADC_TM5_M_MEAS_EN))
+			continue;
+
+		lower_set = (status_low & BIT(ch)) &&
+			(ctl & ADC_TM5_M_LOW_THR_INT_EN);
+
+		upper_set = (status_high & BIT(ch)) &&
+			(ctl & ADC_TM5_M_HIGH_THR_INT_EN);
+
+		if (upper_set || lower_set)
+			thermal_zone_device_update(chip->channels[i].tzd,
+						   THERMAL_EVENT_UNSPECIFIED);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int adc_tm5_get_temp(void *data, int *temp)
+{
+	struct adc_tm5_channel *channel = data;
+	int ret;
+
+	if (!channel || !channel->iio)
+		return -EINVAL;
+
+	ret = iio_read_channel_processed(channel->iio, temp);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static int adc_tm5_disable_channel(struct adc_tm5_channel *channel)
+{
+	struct adc_tm5_chip *chip = channel->chip;
+	unsigned int reg = ADC_TM5_M_EN(channel->channel);
+
+	return adc_tm5_reg_update(chip, reg,
+				  ADC_TM5_M_MEAS_EN |
+				  ADC_TM5_M_HIGH_THR_INT_EN |
+				  ADC_TM5_M_LOW_THR_INT_EN,
+				  0);
+}
+
+static int adc_tm5_enable(struct adc_tm5_chip *chip)
+{
+	int ret = 0;
+	u8 data = 0;
+
+	data = ADC_TM_EN;
+	ret = adc_tm5_write(chip, ADC_TM_EN_CTL1, &data, sizeof(data));
+	if (ret < 0) {
+		pr_err("adc-tm enable failed\n");
+		return ret;
+	}
+
+	data = ADC_TM_CONV_REQ_EN;
+	ret = adc_tm5_write(chip, ADC_TM_CONV_REQ, &data, sizeof(data));
+	if (ret < 0) {
+		pr_err("adc-tm request conversion failed\n");
+		return ret;
+	}
+
+	return ret;
+}
+
+static int adc_tm5_configure(struct adc_tm5_channel *channel, int low_temp, int high_temp)
+{
+	struct adc_tm5_chip *chip = channel->chip;
+	u8 buf[8];
+	u16 reg = ADC_TM5_M_ADC_CH_SEL_CTL(channel->channel);
+	int ret = 0;
+
+	ret = adc_tm5_read(chip, reg, buf, sizeof(buf));
+	if (ret) {
+		dev_err(chip->dev, "block read failed with %d\n", ret);
+		return ret;
+	}
+
+	/* Update ADC channel select */
+	buf[0] = channel->adc_channel;
+
+	/* Warm temperature corresponds to low voltage threshold */
+	if (high_temp != INT_MAX) {
+		u16 adc_code = qcom_adc_tm5_temp_volt_scale(channel->prescale,
+				chip->data->full_scale_code_volt, high_temp);
+
+		buf[1] = adc_code & 0xff;
+		buf[2] = adc_code >> 8;
+		buf[7] |= ADC_TM5_M_LOW_THR_INT_EN;
+	} else {
+		buf[7] &= ~ADC_TM5_M_LOW_THR_INT_EN;
+	}
+
+	/* Cool temperature corresponds to high voltage threshold */
+	if (low_temp != -INT_MAX) {
+		u16 adc_code = qcom_adc_tm5_temp_volt_scale(channel->prescale,
+				chip->data->full_scale_code_volt, low_temp);
+
+		buf[3] = adc_code & 0xff;
+		buf[4] = adc_code >> 8;
+		buf[7] |= ADC_TM5_M_HIGH_THR_INT_EN;
+	} else {
+		buf[7] &= ~ADC_TM5_M_HIGH_THR_INT_EN;
+	}
+
+	/* Update timer select */
+	buf[5] = ADC5_TIMER_SEL_2;
+
+	/* Set calibration select, hw_settle delay */
+	buf[6] &= ~ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK;
+	buf[6] |= FIELD_PREP(ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK, channel->hw_settle_time);
+	buf[6] &= ~ADC_TM5_M_CTL_CAL_SEL_MASK;
+	buf[6] |= FIELD_PREP(ADC_TM5_M_CTL_CAL_SEL_MASK, channel->cal_method);
+
+	buf[7] |= ADC_TM5_M_MEAS_EN;
+
+	ret = adc_tm5_write(chip, reg, buf, sizeof(buf));
+	if (ret) {
+		dev_err(chip->dev, "buf write failed\n");
+		return ret;
+	}
+
+	return adc_tm5_enable(chip);
+}
+
+static int adc_tm5_set_trips(void *data, int low_temp, int high_temp)
+{
+	struct adc_tm5_channel *channel = data;
+	struct adc_tm5_chip *chip;
+	int ret;
+
+	if (!channel)
+		return -EINVAL;
+
+	chip = channel->chip;
+	dev_dbg(chip->dev, "%d:low_temp(mdegC):%d, high_temp(mdegC):%d\n",
+		channel->channel, low_temp, high_temp);
+
+	if (high_temp == INT_MAX && low_temp <= -INT_MAX)
+		ret = adc_tm5_disable_channel(channel);
+	else
+		ret = adc_tm5_configure(channel, low_temp, high_temp);
+
+	return ret;
+}
+
+static struct thermal_zone_of_device_ops adc_tm5_ops = {
+	.get_temp = adc_tm5_get_temp,
+	.set_trips = adc_tm5_set_trips,
+};
+
+static int adc_tm5_register_tzd(struct adc_tm5_chip *adc_tm)
+{
+	unsigned int i;
+	struct thermal_zone_device *tzd;
+
+	for (i = 0; i < adc_tm->nchannels; i++) {
+		adc_tm->channels[i].chip = adc_tm;
+
+		tzd = devm_thermal_zone_of_sensor_register(adc_tm->dev,
+							   adc_tm->channels[i].channel,
+							   &adc_tm->channels[i],
+							   &adc_tm5_ops);
+		if (IS_ERR(tzd)) {
+			dev_err(adc_tm->dev, "Error registering TZ zone:%ld for channel:%d\n",
+				PTR_ERR(tzd), adc_tm->channels[i].channel);
+			continue;
+		}
+		adc_tm->channels[i].tzd = tzd;
+	}
+
+	return 0;
+}
+
+static int adc_tm5_init(struct adc_tm5_chip *chip)
+{
+	u8 buf[4], channels_available;
+	int ret;
+	unsigned int i;
+
+	ret = adc_tm5_read(chip, ADC_TM5_NUM_BTM,
+			   &channels_available, sizeof(channels_available));
+	if (ret) {
+		dev_err(chip->dev, "read failed for BTM channels\n");
+		return ret;
+	}
+
+	/* Select decimation */
+	buf[0] = chip->decimation;
+
+	/* Select number of samples in fast average mode */
+	buf[1] = chip->avg_samples | ADC_TM5_FAST_AVG_EN;
+
+	/* Select timer1 */
+	buf[2] = ADC_TM5_TIMER1;
+
+	/* Select timer2 and timer3 */
+	buf[3] = FIELD_PREP(ADC_TM5_MEAS_INTERVAL_CTL2_MASK, ADC_TM5_TIMER2) |
+		 FIELD_PREP(ADC_TM5_MEAS_INTERVAL_CTL3_MASK, ADC_TM5_TIMER3);
+
+	ret = adc_tm5_write(chip, ADC_TM5_ADC_DIG_PARAM, buf, sizeof(buf));
+	if (ret)
+		dev_err(chip->dev, "block write failed with %d\n", ret);
+
+	for (i = 0; i < chip->nchannels; i++) {
+		if (chip->channels[i].channel >= channels_available) {
+			dev_err(chip->dev, "Invalid channel %d\n", chip->channels[i].channel);
+			return -EINVAL;
+		}
+	}
+
+	return ret;
+}
+
+static int adc_tm5_get_dt_channel_data(struct adc_tm5_chip *adc_tm,
+				       struct adc_tm5_channel *channel,
+				       struct device_node *node)
+{
+	const char *name = node->name;
+	u32 chan, value, varr[2];
+	int ret;
+	struct device *dev = adc_tm->dev;
+	struct of_phandle_args args;
+
+	ret = of_property_read_u32(node, "reg", &chan);
+	if (ret) {
+		dev_err(dev, "%s: invalid channel number (%d)\n", name, ret);
+		return ret;
+	}
+
+	if (chan >= ADC_TM5_NUM_CHANNELS) {
+		dev_err(dev, "%s: invalid channel number %d\n", name, chan);
+		return -EINVAL;
+	}
+
+	/* the channel has DT description */
+	channel->channel = chan;
+
+	/*
+	 * We are tied to PMIC's ADC controller, which always use single
+	 * argument for channel number.  So don't bother parsing
+	 * #io-channel-cells, just enforce cell_count = 1.
+	 */
+	ret = of_parse_phandle_with_fixed_args(node, "io-channels", 1, 0, &args);
+	if (ret < 0) {
+		dev_err(dev, "%s: invalid ADC channel number %d: %d\n", name, chan, ret);
+		return ret;
+	}
+	of_node_put(args.np);
+
+	if (args.args_count != 1 || args.args[0] >= ADC5_MAX_CHANNEL) {
+		dev_err(dev, "%s: invalid ADC channel number %d\n", name, chan);
+		return ret;
+	}
+	channel->adc_channel = args.args[0];
+
+	channel->iio = devm_of_iio_channel_get_by_name(adc_tm->dev, node, NULL);
+	if (IS_ERR(channel->iio)) {
+		ret = PTR_ERR(channel->iio);
+		channel->iio = NULL;
+		if (ret != -EPROBE_DEFER)
+			dev_err(dev, "%s: error getting channel: %d\n", name, ret);
+		return ret;
+	}
+
+	ret = of_property_read_u32_array(node, "qcom,pre-scaling", varr, 2);
+	if (!ret) {
+		ret = qcom_adc5_prescaling_from_dt(varr[0], varr[1]);
+		if (ret < 0) {
+			dev_err(dev, "%s: invalid pre-scaling <%d %d>\n",
+				name, varr[0], varr[1]);
+			return ret;
+		}
+		channel->prescale = ret;
+	} else {
+		/* 1:1 prescale is index 0 */
+		channel->prescale = 0;
+	}
+
+	ret = of_property_read_u32(node, "qcom,hw-settle-time-us", &value);
+	if (!ret) {
+		ret = qcom_adc5_hw_settle_time_from_dt(value, adc_tm->data->hw_settle);
+		if (ret < 0) {
+			dev_err(dev, "%s invalid hw-settle-time-us %d us\n",
+				name, value);
+			return ret;
+		}
+		channel->hw_settle_time = ret;
+	} else {
+		channel->hw_settle_time = VADC_DEF_HW_SETTLE_TIME;
+	}
+
+	if (of_property_read_bool(node, "qcom,ratiometric"))
+		channel->cal_method = ADC_TM5_RATIOMETRIC_CAL;
+	else
+		channel->cal_method = ADC_TM5_ABSOLUTE_CAL;
+
+	return 0;
+}
+
+static int adc_tm5_get_dt_data(struct adc_tm5_chip *adc_tm, struct device_node *node)
+{
+	struct adc_tm5_channel *channels;
+	struct device_node *child;
+	u32 value;
+	int ret;
+	struct device *dev = adc_tm->dev;
+
+	adc_tm->nchannels = of_get_available_child_count(node);
+	if (!adc_tm->nchannels)
+		return -EINVAL;
+
+	adc_tm->channels = devm_kcalloc(dev, adc_tm->nchannels,
+					sizeof(*adc_tm->channels), GFP_KERNEL);
+	if (!adc_tm->channels)
+		return -ENOMEM;
+
+	channels = adc_tm->channels;
+
+	adc_tm->data = of_device_get_match_data(dev);
+	if (!adc_tm->data)
+		adc_tm->data = &adc_tm5_data_pmic;
+
+	ret = of_property_read_u32(node, "qcom,decimation", &value);
+	if (!ret) {
+		ret = qcom_adc5_decimation_from_dt(value, adc_tm->data->decimation);
+		if (ret < 0) {
+			dev_err(dev, "invalid decimation %d\n", value);
+			return ret;
+		}
+		adc_tm->decimation = ret;
+	} else {
+		adc_tm->decimation = ADC5_DECIMATION_DEFAULT;
+	}
+
+	ret = of_property_read_u32(node, "qcom,avg-samples", &value);
+	if (!ret) {
+		ret = qcom_adc5_avg_samples_from_dt(value);
+		if (ret < 0) {
+			dev_err(dev, "invalid avg-samples %d\n", value);
+			return ret;
+		}
+		adc_tm->avg_samples = ret;
+	} else {
+		adc_tm->avg_samples = VADC_DEF_AVG_SAMPLES;
+	}
+
+	for_each_available_child_of_node(node, child) {
+		ret = adc_tm5_get_dt_channel_data(adc_tm, channels, child);
+		if (ret) {
+			of_node_put(child);
+			return ret;
+		}
+
+		channels++;
+	}
+
+	return 0;
+}
+
+static int adc_tm5_probe(struct platform_device *pdev)
+{
+	struct device_node *node = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	struct adc_tm5_chip *adc_tm;
+	struct regmap *regmap;
+	int ret, irq;
+	u32 reg;
+
+	regmap = dev_get_regmap(dev->parent, NULL);
+	if (!regmap)
+		return -ENODEV;
+
+	ret = of_property_read_u32(node, "reg", &reg);
+	if (ret)
+		return ret;
+
+	adc_tm = devm_kzalloc(&pdev->dev, sizeof(*adc_tm), GFP_KERNEL);
+	if (!adc_tm)
+		return -ENOMEM;
+
+	adc_tm->regmap = regmap;
+	adc_tm->dev = dev;
+	adc_tm->base = reg;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(dev, "get_irq failed: %d\n", irq);
+		return irq;
+	}
+
+	ret = adc_tm5_get_dt_data(adc_tm, node);
+	if (ret) {
+		dev_err(dev, "get dt data failed: %d\n", ret);
+		return ret;
+	}
+
+	ret = adc_tm5_init(adc_tm);
+	if (ret) {
+		dev_err(dev, "adc-tm init failed\n");
+		return ret;
+	}
+
+	ret = adc_tm5_register_tzd(adc_tm);
+	if (ret) {
+		dev_err(dev, "tzd register failed\n");
+		return ret;
+	}
+
+	return devm_request_threaded_irq(dev, irq, NULL, adc_tm5_isr,
+					 IRQF_ONESHOT, "pm-adc-tm5", adc_tm);
+}
+
+static const struct of_device_id adc_tm5_match_table[] = {
+	{
+		.compatible = "qcom,spmi-adc-tm5",
+		.data = &adc_tm5_data_pmic,
+	},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, adc_tm5_match_table);
+
+static struct platform_driver adc_tm5_driver = {
+	.driver = {
+		.name = "qcom-spmi-adc-tm5",
+		.of_match_table = adc_tm5_match_table,
+	},
+	.probe = adc_tm5_probe,
+};
+module_platform_driver(adc_tm5_driver);
+
+MODULE_DESCRIPTION("SPMI PMIC Thermal Monitor ADC driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/iio/adc/qcom-vadc-common.h b/include/linux/iio/adc/qcom-vadc-common.h
index 03a9119edc71..041d1397995e 100644
--- a/include/linux/iio/adc/qcom-vadc-common.h
+++ b/include/linux/iio/adc/qcom-vadc-common.h
@@ -174,6 +174,9 @@ int qcom_adc5_hw_scale(enum vadc_scale_fn_type scaletype,
 		    const struct adc5_data *data,
 		    u16 adc_code, int *result_mdec);
 
+u16 qcom_adc_tm5_temp_volt_scale(unsigned int prescale_ratio,
+				 u32 full_scale_code_volt, int temp);
+
 int qcom_adc5_prescaling_from_dt(u32 num, u32 den);
 
 int qcom_adc5_hw_settle_time_from_dt(u32 value, const unsigned int *hw_settle);
-- 
2.28.0


^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v8 09/11] arm64: dts: qcom: pm8150x: add definitions for adc-tm5 part
  2020-10-09 15:44 [PATCH v8 00/11] qcom: pm8150: add support for thermal monitoring Dmitry Baryshkov
                   ` (7 preceding siblings ...)
  2020-10-09 15:44 ` [PATCH v8 08/11] thermal: qcom: add support for adc-tm5 PMIC thermal monitor Dmitry Baryshkov
@ 2020-10-09 15:44 ` Dmitry Baryshkov
  2020-10-09 15:44 ` [PATCH v8 10/11] arm64: dts: sm8250-mtp: add thermal zones using pmic's adc-tm5 Dmitry Baryshkov
  2020-10-09 15:44 ` [PATCH v8 11/11] arm64: dts: qrb5165-rb5: port thermal zone definitions Dmitry Baryshkov
  10 siblings, 0 replies; 13+ messages in thread
From: Dmitry Baryshkov @ 2020-10-09 15:44 UTC (permalink / raw)
  To: Andy Gross, Bjorn Andersson, Rob Herring, Zhang Rui,
	Daniel Lezcano, Amit Kucheria, Jonathan Cameron, Hartmut Knaack,
	Lars-Peter Clausen, Peter Meerwald-Stadler
  Cc: linux-arm-msm, linux-pm, devicetree, linux-iio,
	Manivannan Sadhasivam, Jishnu Prakash

Define adc-tm5 thermal monitoring part. Individual channes and thermal
zones are to be configured in per-device dts files.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 arch/arm64/boot/dts/qcom/pm8150.dtsi  | 10 ++++++++++
 arch/arm64/boot/dts/qcom/pm8150b.dtsi | 10 ++++++++++
 arch/arm64/boot/dts/qcom/pm8150l.dtsi | 10 ++++++++++
 3 files changed, 30 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/pm8150.dtsi b/arch/arm64/boot/dts/qcom/pm8150.dtsi
index 1b6406927509..b1b518c6a2c9 100644
--- a/arch/arm64/boot/dts/qcom/pm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8150.dtsi
@@ -97,6 +97,16 @@ die-temp@6 {
 			};
 		};
 
+		pm8150_adc_tm: adc-tm@3500 {
+			compatible = "qcom,spmi-adc-tm5";
+			reg = <0x3500>;
+			interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		rtc@6000 {
 			compatible = "qcom,pm8941-rtc";
 			reg = <0x6000>;
diff --git a/arch/arm64/boot/dts/qcom/pm8150b.dtsi b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
index e112e8876db6..8e2f3250c914 100644
--- a/arch/arm64/boot/dts/qcom/pm8150b.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
@@ -95,6 +95,16 @@ chg-temp@9 {
 			};
 		};
 
+		pm8150b_adc_tm: adc-tm@3500 {
+			compatible = "qcom,spmi-adc-tm5";
+			reg = <0x3500>;
+			interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		pm8150b_gpios: gpio@c000 {
 			compatible = "qcom,pm8150b-gpio";
 			reg = <0xc000>;
diff --git a/arch/arm64/boot/dts/qcom/pm8150l.dtsi b/arch/arm64/boot/dts/qcom/pm8150l.dtsi
index 62139538b7d9..9f214ceec2b7 100644
--- a/arch/arm64/boot/dts/qcom/pm8150l.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8150l.dtsi
@@ -89,6 +89,16 @@ die-temp@6 {
 			};
 		};
 
+		pm8150l_adc_tm: adc-tm@3500 {
+			compatible = "qcom,spmi-adc-tm5";
+			reg = <0x3500>;
+			interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		pm8150l_gpios: gpio@c000 {
 			compatible = "qcom,pm8150l-gpio";
 			reg = <0xc000>;
-- 
2.28.0


^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v8 10/11] arm64: dts: sm8250-mtp: add thermal zones using pmic's adc-tm5
  2020-10-09 15:44 [PATCH v8 00/11] qcom: pm8150: add support for thermal monitoring Dmitry Baryshkov
                   ` (8 preceding siblings ...)
  2020-10-09 15:44 ` [PATCH v8 09/11] arm64: dts: qcom: pm8150x: add definitions for adc-tm5 part Dmitry Baryshkov
@ 2020-10-09 15:44 ` Dmitry Baryshkov
  2020-10-09 15:44 ` [PATCH v8 11/11] arm64: dts: qrb5165-rb5: port thermal zone definitions Dmitry Baryshkov
  10 siblings, 0 replies; 13+ messages in thread
From: Dmitry Baryshkov @ 2020-10-09 15:44 UTC (permalink / raw)
  To: Andy Gross, Bjorn Andersson, Rob Herring, Zhang Rui,
	Daniel Lezcano, Amit Kucheria, Jonathan Cameron, Hartmut Knaack,
	Lars-Peter Clausen, Peter Meerwald-Stadler
  Cc: linux-arm-msm, linux-pm, devicetree, linux-iio,
	Manivannan Sadhasivam, Jishnu Prakash

Port thermal zones definitions from msm-4.19 tree. Enable and add
channel configuration to PMIC's ADC-TM definitions. Declare thermal
zones and respective trip points.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8250-mtp.dts | 207 ++++++++++++++++++++++++
 1 file changed, 207 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
index 98675e1f8204..95050f7d11f2 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
@@ -24,6 +24,104 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	thermal-zones {
+		xo-therm {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8150_adc_tm 0>;
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		skin-therm {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8150_adc_tm 1>;
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		mmw-pa1 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8150_adc_tm 2>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		conn-therm {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8150b_adc_tm 0>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		camera-therm {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8150l_adc_tm 0>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		skin-msm-therm {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8150l_adc_tm 1>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		mmw-pa2 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8150l_adc_tm 2>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+	};
+
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vph_pwr";
@@ -378,6 +476,115 @@ &i2c15 {
 	/* rtc6226 @ 64 */
 };
 
+&pm8150_adc {
+	xo-therm@4c {
+		reg = <ADC5_XO_THERM_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+
+	skin-therm@4d {
+		reg = <ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+
+	pa-therm1@4e {
+		reg = <ADC5_AMUX_THM2_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+};
+
+&pm8150b_adc {
+	conn-therm@4f {
+		reg = <ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+};
+
+&pm8150l_adc {
+	camera-flash-therm@4d {
+		reg = <ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+
+	skin-msm-therm@4e {
+		reg = <ADC5_AMUX_THM2_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+
+	pa-therm2@4f {
+		reg = <ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+};
+
+&pm8150_adc_tm {
+	status = "okay";
+
+	xo-therm@0 {
+		reg = <0>;
+		io-channels = <&pm8150_adc ADC5_XO_THERM_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	skin-therm@1 {
+		reg = <1>;
+		io-channels = <&pm8150_adc ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	pa-therm1@2 {
+		reg = <2>;
+		io-channels = <&pm8150_adc ADC5_AMUX_THM2_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
+&pm8150b_adc_tm {
+	status = "okay";
+
+	conn-therm@0 {
+		reg = <0>;
+		io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
+&pm8150l_adc_tm {
+	status = "okay";
+
+	camera-flash-therm@0 {
+		reg = <0>;
+		io-channels = <&pm8150l_adc ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	skin-msm-therm@1 {
+		reg = <1>;
+		io-channels = <&pm8150l_adc ADC5_AMUX_THM2_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	pa-therm2@2 {
+		reg = <2>;
+		io-channels = <&pm8150l_adc ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };
-- 
2.28.0


^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v8 11/11] arm64: dts: qrb5165-rb5: port thermal zone definitions
  2020-10-09 15:44 [PATCH v8 00/11] qcom: pm8150: add support for thermal monitoring Dmitry Baryshkov
                   ` (9 preceding siblings ...)
  2020-10-09 15:44 ` [PATCH v8 10/11] arm64: dts: sm8250-mtp: add thermal zones using pmic's adc-tm5 Dmitry Baryshkov
@ 2020-10-09 15:44 ` Dmitry Baryshkov
  10 siblings, 0 replies; 13+ messages in thread
From: Dmitry Baryshkov @ 2020-10-09 15:44 UTC (permalink / raw)
  To: Andy Gross, Bjorn Andersson, Rob Herring, Zhang Rui,
	Daniel Lezcano, Amit Kucheria, Jonathan Cameron, Hartmut Knaack,
	Lars-Peter Clausen, Peter Meerwald-Stadler
  Cc: linux-arm-msm, linux-pm, devicetree, linux-iio,
	Manivannan Sadhasivam, Jishnu Prakash

Add thermal zones definitions basing on the downstream kernel.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 154 +++++++++++++++++++++++
 1 file changed, 154 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
index 1528a865f1f8..6cb8688910a2 100644
--- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
+++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
@@ -58,6 +58,77 @@ bt {
 
 	};
 
+	thermal-zones {
+		xo-therm {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8150_adc_tm 0>;
+			trips {
+				active-config0 {
+					temperature = <50000>;
+					hysteresis = <4000>;
+					type = "passive";
+				};
+			};
+		};
+
+		wifi-therm {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8150_adc_tm 1>;
+			trips {
+				active-config0 {
+					temperature = <52000>;
+					hysteresis = <4000>;
+					type = "passive";
+				};
+			};
+		};
+
+		conn-therm {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8150b_adc_tm 0>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		skin-msm-therm {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8150l_adc_tm 0>;
+
+			trips {
+				active-config0 {
+					temperature = <50000>;
+					hysteresis = <4000>;
+					type = "passive";
+				};
+			};
+		};
+
+		pm8150l-therm {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8150l_adc_tm 1>;
+
+			trips {
+				active-config0 {
+					temperature = <50000>;
+					hysteresis = <4000>;
+					type = "passive";
+				};
+			};
+		};
+
+	};
+
 	vbat: vbat-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "VBAT";
@@ -412,6 +483,89 @@ &i2c15 {
 	status = "okay";
 };
 
+&pm8150_adc {
+	xo-therm@4c {
+		reg = <ADC5_XO_THERM_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+
+	wifi-therm@4e {
+		reg = <ADC5_AMUX_THM2_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+};
+
+&pm8150b_adc {
+	conn-therm@4f {
+		reg = <ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+};
+
+&pm8150l_adc {
+	skin-msm-therm@4e {
+		reg = <ADC5_AMUX_THM2_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+
+	pm8150l-therm@4f {
+		reg = <ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+};
+
+&pm8150_adc_tm {
+	status = "okay";
+
+	xo-therm@0 {
+		reg = <0>;
+		io-channels = <&pm8150_adc ADC5_XO_THERM_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	wifi-therm@1 {
+		reg = <1>;
+		io-channels = <&pm8150_adc ADC5_AMUX_THM2_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
+&pm8150b_adc_tm {
+	status = "okay";
+
+	conn-therm@0 {
+		reg = <0>;
+		io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
+&pm8150l_adc_tm {
+	status = "okay";
+
+	skin-msm-therm@0 {
+		reg = <0>;
+		io-channels = <&pm8150l_adc ADC5_AMUX_THM2_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	pm8150l-therm@1 {
+		reg = <1>;
+		io-channels = <&pm8150l_adc ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
 &pm8150_gpios {
 	gpio-reserved-ranges = <1 1>, <3 2>, <7 1>;
 	gpio-line-names =
-- 
2.28.0


^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: [PATCH v8 08/11] thermal: qcom: add support for adc-tm5 PMIC thermal monitor
  2020-10-09 15:44 ` [PATCH v8 08/11] thermal: qcom: add support for adc-tm5 PMIC thermal monitor Dmitry Baryshkov
@ 2020-10-14 16:32   ` mka
  0 siblings, 0 replies; 13+ messages in thread
From: mka @ 2020-10-14 16:32 UTC (permalink / raw)
  To: Dmitry Baryshkov
  Cc: Andy Gross, Bjorn Andersson, Rob Herring, Zhang Rui,
	Daniel Lezcano, Amit Kucheria, Jonathan Cameron, Hartmut Knaack,
	Lars-Peter Clausen, Peter Meerwald-Stadler, linux-arm-msm,
	linux-pm, devicetree, linux-iio, Manivannan Sadhasivam,
	Jishnu Prakash

Hi,

only a shallow review, I'm not an expert in the area and didn't look into all
aspects of this patch.

On Fri, Oct 09, 2020 at 06:44:56PM +0300, Dmitry Baryshkov wrote:
> Add support for Thermal Monitoring part of PMIC5. This part is closely
> coupled with ADC, using it's channels directly. ADC-TM support
> generating interrupts on ADC value crossing low or high voltage bounds,
> which is used to support thermal trip points.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>  drivers/iio/adc/qcom-vadc-common.c       |  62 +++
>  drivers/thermal/qcom/Kconfig             |  11 +
>  drivers/thermal/qcom/Makefile            |   1 +
>  drivers/thermal/qcom/qcom-spmi-adc-tm5.c | 619 +++++++++++++++++++++++
>  include/linux/iio/adc/qcom-vadc-common.h |   3 +
>  5 files changed, 696 insertions(+)
>  create mode 100644 drivers/thermal/qcom/qcom-spmi-adc-tm5.c
> 
> diff --git a/drivers/iio/adc/qcom-vadc-common.c b/drivers/iio/adc/qcom-vadc-common.c
> index ee94774b72e6..8ceefb079712 100644
> --- a/drivers/iio/adc/qcom-vadc-common.c
> +++ b/drivers/iio/adc/qcom-vadc-common.c
> @@ -376,6 +376,42 @@ static int qcom_vadc_map_voltage_temp(const struct vadc_map_pt *pts,
>  	return 0;
>  }
>  
> +static s32 qcom_vadc_map_temp_voltage(const struct vadc_map_pt *pts,
> +				      u32 tablesize, int input)
> +{
> +	bool descending = 1;

s/1/true

Consider changing to 'ascending' which probably is the more common case, at
least for folks reading the code it's more straightforward to first handle
the 'normal' case and then the odd one.


> +	u32 i = 0;
> +
> +	/* Check if table is descending or ascending */

Comment doesn't add much value, it's evident from the code/assignment of
'descending'

> +	if (tablesize > 1) {
> +		if (pts[0].y < pts[1].y)
> +			descending = 0;

s/0/false/

> +	}
> +
> +	while (i < tablesize) {
> +		if (descending && pts[i].y < input) {
> +			/* table entry is less than measured*/
> +			 /* value and table is descending, stop */

Multiline comment format (https://www.kernel.org/doc/html/v5.9/process/coding-style.html#commenting)

Besides that, the comment is a literal translation of the condition to English,
which isn't useful. 

> +			break;
> +		} else if ((!descending) && pts[i].y > input) {

no need for parentheses around '!descending'

> +			/* table entry is greater than measured*/
> +			/*value and table is ascending, stop */

ditto

> +			break;
> +		}
> +		i++;
> +	}
> +
> +	if (i == 0)
> +		return pts[0].x;
> +	if (i == tablesize)
> +		return pts[tablesize - 1].x;
> +
> +	/* result is between search_index and search_index-1 */
> +	/* interpolate linearly */

Comment doesn't add any value, the name of the function makes it clear that
a linear interpolation is done.

> +	return fixp_linear_interpolate(pts[i - 1].y, pts[i - 1].x,
> +			pts[i].y, pts[i].x, input);
> +}
> +
>  static void qcom_vadc_scale_calib(const struct vadc_linear_graph *calib_graph,
>  				  u16 adc_code,
>  				  bool absolute,
> @@ -473,6 +509,19 @@ static int qcom_vadc_scale_chg_temp(const struct vadc_linear_graph *calib_graph,
>  	return 0;
>  }
>  
> +static u16 qcom_vadc_scale_voltage_code(int voltage,
> +					const struct vadc_prescale_ratio *prescale,
> +					const u32 full_scale_code_volt,
> +					unsigned int factor)
> +{
> +	s64 volt = voltage, adc_vdd_ref_mv = 1875;

This is hard to read, I'd suggest to declare 'volt' and 'adc_vdd_ref_mv'
in separate lines. Actually there is no need for 'adc_vdd_ref_mv', just define
a constant for it.

> +
> +	volt *= prescale->num * factor * full_scale_code_volt;
> +	volt = div64_s64(volt, (s64)prescale->den * adc_vdd_ref_mv * 1000);
> +
> +	return volt;
> +}
> +
>  static int qcom_vadc_scale_code_voltage_factor(u16 adc_code,
>  				const struct vadc_prescale_ratio *prescale,
>  				const struct adc5_data *data,
> @@ -657,6 +706,19 @@ int qcom_vadc_scale(enum vadc_scale_fn_type scaletype,
>  }
>  EXPORT_SYMBOL(qcom_vadc_scale);
>  
> +u16 qcom_adc_tm5_temp_volt_scale(unsigned int prescale_ratio,
> +				 u32 full_scale_code_volt, int temp)
> +{
> +	const struct vadc_prescale_ratio *prescale = &adc5_prescale_ratios[prescale_ratio];
> +	s32 voltage;
> +
> +	voltage = qcom_vadc_map_temp_voltage(adcmap_100k_104ef_104fb_1875_vref,
> +					     ARRAY_SIZE(adcmap_100k_104ef_104fb_1875_vref),
> +					     temp);
> +	return qcom_vadc_scale_voltage_code(voltage, prescale, full_scale_code_volt, 1000);
> +}
> +EXPORT_SYMBOL(qcom_adc_tm5_temp_volt_scale);
> +
>  int qcom_adc5_hw_scale(enum vadc_scale_fn_type scaletype,
>  		    unsigned int prescale_ratio,
>  		    const struct adc5_data *data,
> diff --git a/drivers/thermal/qcom/Kconfig b/drivers/thermal/qcom/Kconfig
> index aa9c1d80fae4..8d5ac2df26dc 100644
> --- a/drivers/thermal/qcom/Kconfig
> +++ b/drivers/thermal/qcom/Kconfig
> @@ -10,6 +10,17 @@ config QCOM_TSENS
>  	  Also able to set threshold temperature for both hot and cold and update
>  	  when a threshold is reached.
>  
> +config QCOM_SPMI_ADC_TM5
> +	tristate "Qualcomm SPMI PMIC Thermal Monitor ADC5"
> +	depends on OF && SPMI && IIO
> +	select REGMAP_SPMI
> +	select QCOM_VADC_COMMON
> +	help
> +	  This enables the thermal driver for the ADC thermal monitoring
> +	  device. It shows up as a thermal zone with multiple trip points.
> +	  Thermal client sets threshold temperature for both warm and cool and
> +	  gets updated when a threshold is reached.
> +
>  config QCOM_SPMI_TEMP_ALARM
>  	tristate "Qualcomm SPMI PMIC Temperature Alarm"
>  	depends on OF && SPMI && IIO
> diff --git a/drivers/thermal/qcom/Makefile b/drivers/thermal/qcom/Makefile
> index ec86eef7f6a6..252ea7d9da0b 100644
> --- a/drivers/thermal/qcom/Makefile
> +++ b/drivers/thermal/qcom/Makefile
> @@ -3,4 +3,5 @@ obj-$(CONFIG_QCOM_TSENS)	+= qcom_tsens.o
>  
>  qcom_tsens-y			+= tsens.o tsens-v2.o tsens-v1.o tsens-v0_1.o \
>  				   tsens-8960.o
> +obj-$(CONFIG_QCOM_SPMI_ADC_TM5)	+= qcom-spmi-adc-tm5.o
>  obj-$(CONFIG_QCOM_SPMI_TEMP_ALARM)	+= qcom-spmi-temp-alarm.o
> diff --git a/drivers/thermal/qcom/qcom-spmi-adc-tm5.c b/drivers/thermal/qcom/qcom-spmi-adc-tm5.c
> new file mode 100644
> index 000000000000..9e4d5ae5fe33
> --- /dev/null
> +++ b/drivers/thermal/qcom/qcom-spmi-adc-tm5.c
> @@ -0,0 +1,619 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2012-2020, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2020 Linaro Limited
> + */
> +
> +#include <linux/bitfield.h>
> +#include <linux/iio/adc/qcom-vadc-common.h>
> +#include <linux/iio/consumer.h>
> +#include <linux/interrupt.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/thermal.h>
> +
> +#define ADC5_MAX_CHANNEL                        0xc0
> +#define ADC_TM5_NUM_CHANNELS		8
> +
> +#define ADC_TM5_STATUS_LOW			0x0a
> +
> +#define ADC_TM5_STATUS_HIGH			0x0b
> +
> +#define ADC_TM5_NUM_BTM				0x0f
> +
> +#define ADC_TM5_ADC_DIG_PARAM			0x42
> +
> +#define ADC_TM5_FAST_AVG_CTL			(ADC_TM5_ADC_DIG_PARAM + 1)
> +#define ADC_TM5_FAST_AVG_EN				BIT(7)
> +
> +#define ADC_TM5_MEAS_INTERVAL_CTL		(ADC_TM5_ADC_DIG_PARAM + 2)
> +#define ADC_TM5_TIMER1					3 /* 3.9ms */
> +
> +#define ADC_TM5_MEAS_INTERVAL_CTL2		(ADC_TM5_ADC_DIG_PARAM + 3)
> +#define ADC_TM5_MEAS_INTERVAL_CTL2_MASK			0xf0
> +#define ADC_TM5_TIMER2					10 /* 1 second */
> +#define ADC_TM5_MEAS_INTERVAL_CTL3_MASK			0xf
> +#define ADC_TM5_TIMER3					4 /* 4 second */
> +
> +#define ADC_TM_EN_CTL1				0x46
> +#define ADC_TM_EN					BIT(7)
> +#define ADC_TM_CONV_REQ				0x47
> +#define ADC_TM_CONV_REQ_EN				BIT(7)
> +
> +#define ADC_TM5_M_CHAN_BASE			0x60
> +
> +#define ADC_TM5_M_ADC_CH_SEL_CTL(n)		(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 0)
> +#define ADC_TM5_M_LOW_THR0(n)			(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 1)
> +#define ADC_TM5_M_LOW_THR1(n)			(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 2)
> +#define ADC_TM5_M_HIGH_THR0(n)			(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 3)
> +#define ADC_TM5_M_HIGH_THR1(n)			(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 4)
> +#define ADC_TM5_M_MEAS_INTERVAL_CTL(n)		(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 5)
> +#define ADC_TM5_M_CTL(n)			(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 6)
> +#define ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK		0xf
> +#define ADC_TM5_M_CTL_CAL_SEL_MASK			0x30
> +#define ADC_TM5_M_CTL_CAL_VAL				0x40
> +#define ADC_TM5_M_EN(n)				(ADC_TM5_M_CHAN_BASE + ((n) * 8) + 7)
> +#define ADC_TM5_M_MEAS_EN				BIT(7)
> +#define ADC_TM5_M_HIGH_THR_INT_EN			BIT(1)
> +#define ADC_TM5_M_LOW_THR_INT_EN			BIT(0)
> +
> +enum adc5_timer_select {
> +	ADC5_TIMER_SEL_1 = 0,
> +	ADC5_TIMER_SEL_2,
> +	ADC5_TIMER_SEL_3,
> +	ADC5_TIMER_SEL_NONE,
> +};
> +
> +struct adc_tm5_data {
> +	const u32	full_scale_code_volt;
> +	unsigned int	*decimation;
> +	unsigned int	*hw_settle;
> +};
> +
> +enum adc_tm5_cal_method {
> +	ADC_TM5_NO_CAL = 0,
> +	ADC_TM5_RATIOMETRIC_CAL,
> +	ADC_TM5_ABSOLUTE_CAL
> +};
> +
> +struct adc_tm5_chip;
> +
> +/**
> + * struct adc_tm5_channel - ADC Thermal Monitoring channel data.
> + * @channel: channel number.
> + * @adc_channel: corresponding ADC channel number.
> + * @cal_method: calibration method.
> + * @prescale: channel scaling performed on the input signal.
> + * @hw_settle_time: the time between AMUX being configured and the
> + *	start of conversion.
> + * @iio: IIO channel instance used by this channel.
> + * @chip: ADC TM chip instance.
> + * @tzd: thermal zone device used by this channel.
> + */
> +struct adc_tm5_channel {
> +	unsigned int		channel;
> +	unsigned int		adc_channel;
> +	enum adc_tm5_cal_method	cal_method;
> +	unsigned int		prescale;
> +	unsigned int		hw_settle_time;
> +	struct iio_channel	*iio;
> +	struct adc_tm5_chip	*chip;
> +	struct thermal_zone_device *tzd;
> +};
> +
> +/**
> + * struct adc_tm5_chip - ADC Thermal Monitoring properties
> + * @regmap: SPMI ADC5 Thermal Monitoring  peripheral register map field.
> + * @dev: SPMI ADC5 device.
> + * @data: software configuration data.
> + * @channels: array of ADC TM channel data.
> + * @nchannels: amount of channels defined/allocated
> + * @decimation: sampling rate supported for the channel.
> + * @avg_samples: ability to provide single result from the ADC
> + *	that is an average of multiple measurements.
> + * @base: base address of TM registers.
> + */
> +struct adc_tm5_chip {
> +	struct regmap		*regmap;
> +	struct device		*dev;
> +	const struct adc_tm5_data	*data;
> +	struct adc_tm5_channel	*channels;
> +	unsigned int		nchannels;
> +	unsigned int		decimation;
> +	unsigned int		avg_samples;
> +	u16			base;
> +};
> +
> +static const struct adc_tm5_data adc_tm5_data_pmic = {
> +	.full_scale_code_volt = 0x70e4,
> +	.decimation = (unsigned int []) { 250, 420, 840 },
> +	.hw_settle = (unsigned int []) { 15, 100, 200, 300, 400, 500, 600, 700,
> +					 1000, 2000, 4000, 8000, 16000, 32000,
> +					 64000, 128000 },
> +};
> +
> +static int adc_tm5_read(struct adc_tm5_chip *adc_tm, u16 offset, u8 *data, int len)
> +{
> +	return regmap_bulk_read(adc_tm->regmap, adc_tm->base + offset, data, len);
> +}
> +
> +static int adc_tm5_write(struct adc_tm5_chip *adc_tm, u16 offset, u8 *data, int len)
> +{
> +	return regmap_bulk_write(adc_tm->regmap, adc_tm->base + offset, data, len);
> +}
> +
> +static int adc_tm5_reg_update(struct adc_tm5_chip *adc_tm, u16 offset, u8 mask, u8 val)
> +{
> +	return regmap_write_bits(adc_tm->regmap, adc_tm->base + offset, mask, val);
> +}
> +
> +static irqreturn_t adc_tm5_isr(int irq, void *data)
> +{
> +	struct adc_tm5_chip *chip = data;
> +	u8 status_low, status_high, ctl;
> +	int ret = 0, i = 0;

no need for initialization

> +
> +	ret = adc_tm5_read(chip, ADC_TM5_STATUS_LOW, &status_low, sizeof(status_low));
> +	if (unlikely(ret)) {
> +		dev_err(chip->dev, "read status low failed with %d\n", ret);

s/ with %d/: %d/
> +		return IRQ_HANDLED;
> +	}
> +
> +	ret = adc_tm5_read(chip, ADC_TM5_STATUS_HIGH, &status_high, sizeof(status_high));
> +	if (unlikely(ret)) {
> +		dev_err(chip->dev, "read status high failed with %d\n", ret);

s/ with %d/: %d/

> +		return IRQ_HANDLED;
> +	}
> +
> +	for (i = 0; i < chip->nchannels; i++) {
> +		bool upper_set = false, lower_set = false;
> +		unsigned int ch = chip->channels[i].channel;
> +
> +		if (!chip->channels[i].tzd) {
> +			dev_err_once(chip->dev, "thermal device not found\n");

Add channel number?

I understand that you use 'dev_err_once' to avoid spamming the log. Note that
this creates a single log entry, even when different channels don't have a tzd.

> +			continue;
> +		}
> +
> +		ret = adc_tm5_read(chip, ADC_TM5_M_EN(ch), &ctl, sizeof(ctl));
> +		if (unlikely(ret)) {
> +			dev_err(chip->dev, "ctl read failed with %d\n", ret);

s/ with %d/: %d/

Add channel number?

> +			continue;
> +		}
> +
> +		if (!(ctl & ADC_TM5_M_MEAS_EN))
> +			continue;
> +
> +		lower_set = (status_low & BIT(ch)) &&
> +			(ctl & ADC_TM5_M_LOW_THR_INT_EN);
> +
> +		upper_set = (status_high & BIT(ch)) &&
> +			(ctl & ADC_TM5_M_HIGH_THR_INT_EN);
> +
> +		if (upper_set || lower_set)
> +			thermal_zone_device_update(chip->channels[i].tzd,
> +						   THERMAL_EVENT_UNSPECIFIED);
> +	}
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static int adc_tm5_get_temp(void *data, int *temp)
> +{
> +	struct adc_tm5_channel *channel = data;
> +	int ret;
> +
> +	if (!channel || !channel->iio)
> +		return -EINVAL;
> +
> +	ret = iio_read_channel_processed(channel->iio, temp);
> +	if (ret < 0)
> +		return ret;
> +
> +	return 0;


	return iio_read_channel_processed(channel->iio, temp);

> +}
> +
> +static int adc_tm5_disable_channel(struct adc_tm5_channel *channel)
> +{
> +	struct adc_tm5_chip *chip = channel->chip;
> +	unsigned int reg = ADC_TM5_M_EN(channel->channel);
> +
> +	return adc_tm5_reg_update(chip, reg,
> +				  ADC_TM5_M_MEAS_EN |
> +				  ADC_TM5_M_HIGH_THR_INT_EN |
> +				  ADC_TM5_M_LOW_THR_INT_EN,
> +				  0);
> +}
> +
> +static int adc_tm5_enable(struct adc_tm5_chip *chip)
> +{
> +	int ret = 0;
> +	u8 data = 0;

no need for initializations

> +
> +	data = ADC_TM_EN;
> +	ret = adc_tm5_write(chip, ADC_TM_EN_CTL1, &data, sizeof(data));
> +	if (ret < 0) {
> +		pr_err("adc-tm enable failed\n");

		dev_err(chip->dev, "adc-tm enable failed: %d\n", ret);

> +		return ret;
> +	}
> +
> +	data = ADC_TM_CONV_REQ_EN;
> +	ret = adc_tm5_write(chip, ADC_TM_CONV_REQ, &data, sizeof(data));
> +	if (ret < 0) {
> +		pr_err("adc-tm request conversion failed\n");

		dev_err(chip->dev, "adc-tm request conversion failed: %d\n", ret);

> +		return ret;
> +	}
> +
> +	return ret;

	return 0;
> +}
> +
> +static int adc_tm5_configure(struct adc_tm5_channel *channel, int low_temp, int high_temp)
> +{
> +	struct adc_tm5_chip *chip = channel->chip;
> +	u8 buf[8];
> +	u16 reg = ADC_TM5_M_ADC_CH_SEL_CTL(channel->channel);
> +	int ret = 0;

initialization not needed

> +
> +	ret = adc_tm5_read(chip, reg, buf, sizeof(buf));
> +	if (ret) {
> +		dev_err(chip->dev, "block read failed with %d\n", ret);
> +		return ret;
> +	}
> +
> +	/* Update ADC channel select */

Comment does not add any value

> +	buf[0] = channel->adc_channel;
> +
> +	/* Warm temperature corresponds to low voltage threshold */

Not sure if the comment is useful. In any case use a consistent terminology, the
parameters are called 'low_temp' and 'high_temp', but the comments talk about
warm and cool.

> +	if (high_temp != INT_MAX) {
> +		u16 adc_code = qcom_adc_tm5_temp_volt_scale(channel->prescale,
> +				chip->data->full_scale_code_volt, high_temp);
> +
> +		buf[1] = adc_code & 0xff;
> +		buf[2] = adc_code >> 8;
> +		buf[7] |= ADC_TM5_M_LOW_THR_INT_EN;
> +	} else {
> +		buf[7] &= ~ADC_TM5_M_LOW_THR_INT_EN;
> +	}
> +
> +	/* Cool temperature corresponds to high voltage threshold */
> +	if (low_temp != -INT_MAX) {
> +		u16 adc_code = qcom_adc_tm5_temp_volt_scale(channel->prescale,
> +				chip->data->full_scale_code_volt, low_temp);
> +
> +		buf[3] = adc_code & 0xff;
> +		buf[4] = adc_code >> 8;
> +		buf[7] |= ADC_TM5_M_HIGH_THR_INT_EN;
> +	} else {
> +		buf[7] &= ~ADC_TM5_M_HIGH_THR_INT_EN;
> +	}
> +
> +	/* Update timer select */

Comment not useful

> +	buf[5] = ADC5_TIMER_SEL_2;
> +
> +	/* Set calibration select, hw_settle delay */
> +	buf[6] &= ~ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK;
> +	buf[6] |= FIELD_PREP(ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK, channel->hw_settle_time);
> +	buf[6] &= ~ADC_TM5_M_CTL_CAL_SEL_MASK;
> +	buf[6] |= FIELD_PREP(ADC_TM5_M_CTL_CAL_SEL_MASK, channel->cal_method);
> +
> +	buf[7] |= ADC_TM5_M_MEAS_EN;
> +
> +	ret = adc_tm5_write(chip, reg, buf, sizeof(buf));
> +	if (ret) {
> +		dev_err(chip->dev, "buf write failed\n");

'buf write' isn't very useful information. This writes ADC_TM5_M_ADC_CH_SEL_CTL
for 'channel->channel', right? The message should convey that. Also include the
error in the log.

> +		return ret;
> +	}
> +
> +	return adc_tm5_enable(chip);
> +}
> +
> +static int adc_tm5_set_trips(void *data, int low_temp, int high_temp)

nit: consider naming the parameters 'high'/'low' (like other drivers do),
from the function name it's evident that these are trip point temperatures.


> +{
> +	struct adc_tm5_channel *channel = data;
> +	struct adc_tm5_chip *chip;
> +	int ret;
> +
> +	if (!channel)
> +		return -EINVAL;

Judging from other drivers it doesn't seem this check is needed.

> +
> +	chip = channel->chip;
> +	dev_dbg(chip->dev, "%d:low_temp(mdegC):%d, high_temp(mdegC):%d\n",
> +		channel->channel, low_temp, high_temp);
> +
> +	if (high_temp == INT_MAX && low_temp <= -INT_MAX)
> +		ret = adc_tm5_disable_channel(channel);
> +	else
> +		ret = adc_tm5_configure(channel, low_temp, high_temp);
> +
> +	return ret;
> +}
> +
> +static struct thermal_zone_of_device_ops adc_tm5_ops = {
> +	.get_temp = adc_tm5_get_temp,
> +	.set_trips = adc_tm5_set_trips,
> +};
> +
> +static int adc_tm5_register_tzd(struct adc_tm5_chip *adc_tm)
> +{
> +	unsigned int i;
> +	struct thermal_zone_device *tzd;
> +
> +	for (i = 0; i < adc_tm->nchannels; i++) {
> +		adc_tm->channels[i].chip = adc_tm;
> +
> +		tzd = devm_thermal_zone_of_sensor_register(adc_tm->dev,
> +							   adc_tm->channels[i].channel,
> +							   &adc_tm->channels[i],
> +							   &adc_tm5_ops);
> +		if (IS_ERR(tzd)) {
> +			dev_err(adc_tm->dev, "Error registering TZ zone:%ld for channel:%d\n",
> +				PTR_ERR(tzd), adc_tm->channels[i].channel);
> +			continue;
> +		}
> +		adc_tm->channels[i].tzd = tzd;
> +	}
> +
> +	return 0;
> +}
> +
> +static int adc_tm5_init(struct adc_tm5_chip *chip)
> +{
> +	u8 buf[4], channels_available;
> +	int ret;
> +	unsigned int i;
> +
> +	ret = adc_tm5_read(chip, ADC_TM5_NUM_BTM,
> +			   &channels_available, sizeof(channels_available));
> +	if (ret) {
> +		dev_err(chip->dev, "read failed for BTM channels\n");
> +		return ret;
> +	}
> +
> +	/* Select decimation */

Comment does not add any value

> +	buf[0] = chip->decimation;
> +
> +	/* Select number of samples in fast average mode */

ditto

> +	buf[1] = chip->avg_samples | ADC_TM5_FAST_AVG_EN;
> +
> +	/* Select timer1 */

ditto

> +	buf[2] = ADC_TM5_TIMER1;
> +
> +	/* Select timer2 and timer3 */

ditto

> +	buf[3] = FIELD_PREP(ADC_TM5_MEAS_INTERVAL_CTL2_MASK, ADC_TM5_TIMER2) |
> +		 FIELD_PREP(ADC_TM5_MEAS_INTERVAL_CTL3_MASK, ADC_TM5_TIMER3);
> +
> +	ret = adc_tm5_write(chip, ADC_TM5_ADC_DIG_PARAM, buf, sizeof(buf));
> +	if (ret)
> +		dev_err(chip->dev, "block write failed with %d\n", ret);

Does it make sense to continue after this?

> +
> +	for (i = 0; i < chip->nchannels; i++) {
> +		if (chip->channels[i].channel >= channels_available) {
> +			dev_err(chip->dev, "Invalid channel %d\n", chip->channels[i].channel);
> +			return -EINVAL;
> +		}
> +	}

Shouldn't this be done directly after reading the channel info above, before
writing ADC_TM5_ADC_DIG_PARAM?

> +
> +	return ret;
> +}
> +
> +static int adc_tm5_get_dt_channel_data(struct adc_tm5_chip *adc_tm,
> +				       struct adc_tm5_channel *channel,
> +				       struct device_node *node)
> +{
> +	const char *name = node->name;
> +	u32 chan, value, varr[2];
> +	int ret;
> +	struct device *dev = adc_tm->dev;
> +	struct of_phandle_args args;
> +
> +	ret = of_property_read_u32(node, "reg", &chan);
> +	if (ret) {
> +		dev_err(dev, "%s: invalid channel number (%d)\n", name, ret);
> +		return ret;
> +	}
> +
> +	if (chan >= ADC_TM5_NUM_CHANNELS) {
> +		dev_err(dev, "%s: invalid channel number %d\n", name, chan);
> +		return -EINVAL;
> +	}

Use a consistent log format for invalid channel numbers ('channel number (%d)'
vs 'channel number %d').

> +
> +	/* the channel has DT description */

Comment it useless

> +	channel->channel = chan;
> +
> +	/*
> +	 * We are tied to PMIC's ADC controller, which always use single
> +	 * argument for channel number.  So don't bother parsing
> +	 * #io-channel-cells, just enforce cell_count = 1.
> +	 */
> +	ret = of_parse_phandle_with_fixed_args(node, "io-channels", 1, 0, &args);
> +	if (ret < 0) {
> +		dev_err(dev, "%s: invalid ADC channel number %d: %d\n", name, chan, ret);

Is the problem really an invalid channel number or to parse 'io-channels'?

> +		return ret;
> +	}
> +	of_node_put(args.np);
> +
> +	if (args.args_count != 1 || args.args[0] >= ADC5_MAX_CHANNEL) {
> +		dev_err(dev, "%s: invalid ADC channel number %d\n", name, chan);
> +		return ret;
> +	}
> +	channel->adc_channel = args.args[0];
> +
> +	channel->iio = devm_of_iio_channel_get_by_name(adc_tm->dev, node, NULL);
> +	if (IS_ERR(channel->iio)) {
> +		ret = PTR_ERR(channel->iio);
> +		channel->iio = NULL;

Is this assignement to NULL really necessary? probe() is aborted when
adc_tm5_get_dt_data() fails

> +		if (ret != -EPROBE_DEFER)
> +			dev_err(dev, "%s: error getting channel: %d\n", name, ret);
> +		return ret;
> +	}
> +
> +	ret = of_property_read_u32_array(node, "qcom,pre-scaling", varr, 2);
> +	if (!ret) {
> +		ret = qcom_adc5_prescaling_from_dt(varr[0], varr[1]);
> +		if (ret < 0) {
> +			dev_err(dev, "%s: invalid pre-scaling <%d %d>\n",
> +				name, varr[0], varr[1]);
> +			return ret;
> +		}
> +		channel->prescale = ret;
> +	} else {
> +		/* 1:1 prescale is index 0 */
> +		channel->prescale = 0;
> +	}
> +
> +	ret = of_property_read_u32(node, "qcom,hw-settle-time-us", &value);
> +	if (!ret) {
> +		ret = qcom_adc5_hw_settle_time_from_dt(value, adc_tm->data->hw_settle);
> +		if (ret < 0) {
> +			dev_err(dev, "%s invalid hw-settle-time-us %d us\n",
> +				name, value);
> +			return ret;
> +		}
> +		channel->hw_settle_time = ret;
> +	} else {
> +		channel->hw_settle_time = VADC_DEF_HW_SETTLE_TIME;
> +	}
> +
> +	if (of_property_read_bool(node, "qcom,ratiometric"))
> +		channel->cal_method = ADC_TM5_RATIOMETRIC_CAL;
> +	else
> +		channel->cal_method = ADC_TM5_ABSOLUTE_CAL;
> +
> +	return 0;
> +}
> +
> +static int adc_tm5_get_dt_data(struct adc_tm5_chip *adc_tm, struct device_node *node)
> +{
> +	struct adc_tm5_channel *channels;
> +	struct device_node *child;
> +	u32 value;
> +	int ret;
> +	struct device *dev = adc_tm->dev;
> +
> +	adc_tm->nchannels = of_get_available_child_count(node);
> +	if (!adc_tm->nchannels)
> +		return -EINVAL;
> +
> +	adc_tm->channels = devm_kcalloc(dev, adc_tm->nchannels,
> +					sizeof(*adc_tm->channels), GFP_KERNEL);
> +	if (!adc_tm->channels)
> +		return -ENOMEM;
> +
> +	channels = adc_tm->channels;

Most of the above could be moved before the loop that reads
adc_tm5_get_dt_channel_data(). This would skip the allocation in case of DT
errors and move the variables closer to the context where they are used.

> +
> +	adc_tm->data = of_device_get_match_data(dev);
> +	if (!adc_tm->data)
> +		adc_tm->data = &adc_tm5_data_pmic;
> +
> +	ret = of_property_read_u32(node, "qcom,decimation", &value);
> +	if (!ret) {
> +		ret = qcom_adc5_decimation_from_dt(value, adc_tm->data->decimation);
> +		if (ret < 0) {
> +			dev_err(dev, "invalid decimation %d\n", value);
> +			return ret;
> +		}
> +		adc_tm->decimation = ret;
> +	} else {
> +		adc_tm->decimation = ADC5_DECIMATION_DEFAULT;
> +	}
> +
> +	ret = of_property_read_u32(node, "qcom,avg-samples", &value);
> +	if (!ret) {
> +		ret = qcom_adc5_avg_samples_from_dt(value);
> +		if (ret < 0) {
> +			dev_err(dev, "invalid avg-samples %d\n", value);
> +			return ret;
> +		}
> +		adc_tm->avg_samples = ret;
> +	} else {
> +		adc_tm->avg_samples = VADC_DEF_AVG_SAMPLES;
> +	}
> +
> +	for_each_available_child_of_node(node, child) {
> +		ret = adc_tm5_get_dt_channel_data(adc_tm, channels, child);
> +		if (ret) {
> +			of_node_put(child);
> +			return ret;
> +		}
> +
> +		channels++;
> +	}
> +
> +	return 0;
> +}
> +
> +static int adc_tm5_probe(struct platform_device *pdev)
> +{
> +	struct device_node *node = pdev->dev.of_node;
> +	struct device *dev = &pdev->dev;
> +	struct adc_tm5_chip *adc_tm;
> +	struct regmap *regmap;
> +	int ret, irq;
> +	u32 reg;
> +
> +	regmap = dev_get_regmap(dev->parent, NULL);
> +	if (!regmap)
> +		return -ENODEV;
> +
> +	ret = of_property_read_u32(node, "reg", &reg);
> +	if (ret)
> +		return ret;
> +
> +	adc_tm = devm_kzalloc(&pdev->dev, sizeof(*adc_tm), GFP_KERNEL);
> +	if (!adc_tm)
> +		return -ENOMEM;
> +
> +	adc_tm->regmap = regmap;
> +	adc_tm->dev = dev;
> +	adc_tm->base = reg;
> +
> +	irq = platform_get_irq(pdev, 0);
> +	if (irq < 0) {
> +		dev_err(dev, "get_irq failed: %d\n", irq);
> +		return irq;
> +	}
> +
> +	ret = adc_tm5_get_dt_data(adc_tm, node);
> +	if (ret) {
> +		dev_err(dev, "get dt data failed: %d\n", ret);
> +		return ret;
> +	}
> +
> +	ret = adc_tm5_init(adc_tm);
> +	if (ret) {
> +		dev_err(dev, "adc-tm init failed\n");
> +		return ret;
> +	}
> +
> +	ret = adc_tm5_register_tzd(adc_tm);
> +	if (ret) {
> +		dev_err(dev, "tzd register failed\n");

Is there anything from adc_tm5_init() that needs to be undone?

> +		return ret;
> +	}
> +
> +	return devm_request_threaded_irq(dev, irq, NULL, adc_tm5_isr,
> +					 IRQF_ONESHOT, "pm-adc-tm5", adc_tm);
> +}
> +
> +static const struct of_device_id adc_tm5_match_table[] = {
> +	{
> +		.compatible = "qcom,spmi-adc-tm5",
> +		.data = &adc_tm5_data_pmic,
> +	},
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, adc_tm5_match_table);
> +
> +static struct platform_driver adc_tm5_driver = {
> +	.driver = {
> +		.name = "qcom-spmi-adc-tm5",
> +		.of_match_table = adc_tm5_match_table,
> +	},
> +	.probe = adc_tm5_probe,
> +};
> +module_platform_driver(adc_tm5_driver);
> +
> +MODULE_DESCRIPTION("SPMI PMIC Thermal Monitor ADC driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/include/linux/iio/adc/qcom-vadc-common.h b/include/linux/iio/adc/qcom-vadc-common.h
> index 03a9119edc71..041d1397995e 100644
> --- a/include/linux/iio/adc/qcom-vadc-common.h
> +++ b/include/linux/iio/adc/qcom-vadc-common.h
> @@ -174,6 +174,9 @@ int qcom_adc5_hw_scale(enum vadc_scale_fn_type scaletype,
>  		    const struct adc5_data *data,
>  		    u16 adc_code, int *result_mdec);
>  
> +u16 qcom_adc_tm5_temp_volt_scale(unsigned int prescale_ratio,
> +				 u32 full_scale_code_volt, int temp);
> +
>  int qcom_adc5_prescaling_from_dt(u32 num, u32 den);
>  
>  int qcom_adc5_hw_settle_time_from_dt(u32 value, const unsigned int *hw_settle);
> -- 
> 2.28.0
> 

^ permalink raw reply	[flat|nested] 13+ messages in thread

end of thread, back to index

Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-10-09 15:44 [PATCH v8 00/11] qcom: pm8150: add support for thermal monitoring Dmitry Baryshkov
2020-10-09 15:44 ` [PATCH v8 01/11] dt-bindings: thermal: qcom: add adc-thermal monitor bindings Dmitry Baryshkov
2020-10-09 15:44 ` [PATCH v8 02/11] fixp-arith: add a linear interpolation function Dmitry Baryshkov
2020-10-09 15:44 ` [PATCH v8 03/11] iio: adc: qcom-vadc: move several adc5 functions to common file Dmitry Baryshkov
2020-10-09 15:44 ` [PATCH v8 04/11] iio: adc: qcom-vadc-common: use fixp_linear_interpolate Dmitry Baryshkov
2020-10-09 15:44 ` [PATCH v8 05/11] iio: adc: move qcom-vadc-common.h to include dir Dmitry Baryshkov
2020-10-09 15:44 ` [PATCH v8 06/11] iio: adc: qcom-spmi-adc5: use of_device_get_match_data Dmitry Baryshkov
2020-10-09 15:44 ` [PATCH v8 07/11] iio: provide of_iio_channel_get_by_name() and devm_ version it Dmitry Baryshkov
2020-10-09 15:44 ` [PATCH v8 08/11] thermal: qcom: add support for adc-tm5 PMIC thermal monitor Dmitry Baryshkov
2020-10-14 16:32   ` mka
2020-10-09 15:44 ` [PATCH v8 09/11] arm64: dts: qcom: pm8150x: add definitions for adc-tm5 part Dmitry Baryshkov
2020-10-09 15:44 ` [PATCH v8 10/11] arm64: dts: sm8250-mtp: add thermal zones using pmic's adc-tm5 Dmitry Baryshkov
2020-10-09 15:44 ` [PATCH v8 11/11] arm64: dts: qrb5165-rb5: port thermal zone definitions Dmitry Baryshkov

Linux-ARM-MSM Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-msm/0 linux-arm-msm/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-msm linux-arm-msm/ https://lore.kernel.org/linux-arm-msm \
		linux-arm-msm@vger.kernel.org
	public-inbox-index linux-arm-msm

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-arm-msm


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git