* [PATCH 0/2] arm64: dts: qcom: sm8250: fix display nodes @ 2021-02-11 18:09 Jonathan Marek 2021-02-11 18:09 ` [PATCH 1/2] drm/msm: add compatibles for sm8150/sm8250 display Jonathan Marek 2021-02-11 18:09 ` [PATCH 2/2] arm64: dts: qcom: sm8250: fix display nodes Jonathan Marek 0 siblings, 2 replies; 6+ messages in thread From: Jonathan Marek @ 2021-02-11 18:09 UTC (permalink / raw) To: linux-arm-msm Cc: Andy Gross, Bjorn Andersson, Daniel Vetter, David Airlie, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, Dmitry Baryshkov, Drew Davenport, open list:DRM DRIVER FOR MSM ADRENO GPU, Eric Anholt, open list:DRM DRIVER FOR MSM ADRENO GPU, Jeykumar Sankaran, Jordan Crouse, Kalyan Thota, open list, Qinglang Miao, Rajendra Nayak, Rob Clark, Rob Herring, Sean Paul, Tanmay Shah, tongtiangen Add sm8150/sm8250 compatibles to drm/msm and fix the sm8250 display nodes. Jonathan Marek (2): drm/msm: add compatibles for sm8150/sm8250 display arm64: dts: qcom: sm8250: fix display nodes .../devicetree/bindings/display/msm/dpu.txt | 4 +-- arch/arm64/boot/dts/qcom/sm8250.dtsi | 34 +++++-------------- drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c | 2 ++ drivers/gpu/drm/msm/msm_drv.c | 6 ++-- 4 files changed, 16 insertions(+), 30 deletions(-) -- 2.26.1 ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 1/2] drm/msm: add compatibles for sm8150/sm8250 display 2021-02-11 18:09 [PATCH 0/2] arm64: dts: qcom: sm8250: fix display nodes Jonathan Marek @ 2021-02-11 18:09 ` Jonathan Marek 2021-02-11 18:09 ` [PATCH 2/2] arm64: dts: qcom: sm8250: fix display nodes Jonathan Marek 1 sibling, 0 replies; 6+ messages in thread From: Jonathan Marek @ 2021-02-11 18:09 UTC (permalink / raw) To: linux-arm-msm Cc: Rob Clark, Sean Paul, David Airlie, Daniel Vetter, Rob Herring, Jordan Crouse, Kalyan Thota, Tanmay Shah, Eric Anholt, Drew Davenport, Jeykumar Sankaran, Rajendra Nayak, tongtiangen, Qinglang Miao, open list:DRM DRIVER FOR MSM ADRENO GPU, open list:DRM DRIVER FOR MSM ADRENO GPU, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, open list The driver already has support for sm8150/sm8250, but the compatibles were never added. Also inverse the non-mdp4 condition in add_display_components() to avoid having to check every new compatible in the condition. Signed-off-by: Jonathan Marek <jonathan@marek.ca> --- Documentation/devicetree/bindings/display/msm/dpu.txt | 4 ++-- drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c | 2 ++ drivers/gpu/drm/msm/msm_drv.c | 6 +++--- 3 files changed, 7 insertions(+), 5 deletions(-) diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt index 551ae26f60da..5763f43200a0 100644 --- a/Documentation/devicetree/bindings/display/msm/dpu.txt +++ b/Documentation/devicetree/bindings/display/msm/dpu.txt @@ -8,7 +8,7 @@ The DPU display controller is found in SDM845 SoC. MDSS: Required properties: -- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss" +- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss", "qcom,sm8150-mdss", "qcom,sm8250-mdss" - reg: physical base address and length of contoller's registers. - reg-names: register region names. The following region is required: * "mdss" @@ -41,7 +41,7 @@ Optional properties: MDP: Required properties: -- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu" +- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu", "qcom,sm8150-dpu", "qcom,sm8250-dpu" - reg: physical base address and length of controller's registers. - reg-names : register region names. The following region is required: * "mdp" diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c index 5a8e3e1fc48c..fff12a4c8bfc 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c @@ -1219,6 +1219,8 @@ static const struct dev_pm_ops dpu_pm_ops = { static const struct of_device_id dpu_dt_match[] = { { .compatible = "qcom,sdm845-dpu", }, { .compatible = "qcom,sc7180-dpu", }, + { .compatible = "qcom,sm8150-dpu", }, + { .compatible = "qcom,sm8250-dpu", }, {} }; MODULE_DEVICE_TABLE(of, dpu_dt_match); diff --git a/drivers/gpu/drm/msm/msm_drv.c b/drivers/gpu/drm/msm/msm_drv.c index 94525ac76d4e..928f13d4bfbc 100644 --- a/drivers/gpu/drm/msm/msm_drv.c +++ b/drivers/gpu/drm/msm/msm_drv.c @@ -1185,9 +1185,7 @@ static int add_display_components(struct device *dev, * Populate the children devices, find the MDP5/DPU node, and then add * the interfaces to our components list. */ - if (of_device_is_compatible(dev->of_node, "qcom,mdss") || - of_device_is_compatible(dev->of_node, "qcom,sdm845-mdss") || - of_device_is_compatible(dev->of_node, "qcom,sc7180-mdss")) { + if (!of_device_is_compatible(dev->of_node, "qcom,mdp4")) { ret = of_platform_populate(dev->of_node, NULL, NULL, dev); if (ret) { DRM_DEV_ERROR(dev, "failed to populate children devices\n"); @@ -1320,6 +1318,8 @@ static const struct of_device_id dt_match[] = { { .compatible = "qcom,mdss", .data = (void *)KMS_MDP5 }, { .compatible = "qcom,sdm845-mdss", .data = (void *)KMS_DPU }, { .compatible = "qcom,sc7180-mdss", .data = (void *)KMS_DPU }, + { .compatible = "qcom,sm8150-mdss", .data = (void *)KMS_DPU }, + { .compatible = "qcom,sm8250-mdss", .data = (void *)KMS_DPU }, {} }; MODULE_DEVICE_TABLE(of, dt_match); -- 2.26.1 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/2] arm64: dts: qcom: sm8250: fix display nodes 2021-02-11 18:09 [PATCH 0/2] arm64: dts: qcom: sm8250: fix display nodes Jonathan Marek 2021-02-11 18:09 ` [PATCH 1/2] drm/msm: add compatibles for sm8150/sm8250 display Jonathan Marek @ 2021-02-11 18:09 ` Jonathan Marek 2021-02-11 20:05 ` Dmitry Baryshkov 2021-02-11 20:14 ` kernel test robot 1 sibling, 2 replies; 6+ messages in thread From: Jonathan Marek @ 2021-02-11 18:09 UTC (permalink / raw) To: linux-arm-msm Cc: Andy Gross, Bjorn Andersson, Rob Herring, Dmitry Baryshkov, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, open list Apply these fixes to the newly added sm8250 display ndoes - Use sm8250 compatibles instead of sdm845 compatibles - Remove "notused" interconnect (which apparently was blindly copied from my old patches) - Use dispcc node example from dt-bindings, removing clocks which aren't documented or used by the driver and fixing the region size. Note: also removed the mmcx-supply for dispcc which wasn't documented when it was added. I would have left it there but it is also breaking my use-case (setting a lower power level than what the bootloader sets?). Fixes: 7c1dffd471b1 ("arm64: dts: qcom: sm8250.dtsi: add display system nodes") Signed-off-by: Jonathan Marek <jonathan@marek.ca> --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 34 ++++++++-------------------- 1 file changed, 9 insertions(+), 25 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 947e1accae3a..20a3ff30e924 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -2323,14 +2323,13 @@ usb_2_dwc3: dwc3@a800000 { }; mdss: mdss@ae00000 { - compatible = "qcom,sdm845-mdss"; + compatible = "qcom,sm8250-mdss"; reg = <0 0x0ae00000 0 0x1000>; reg-names = "mdss"; - interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_DISPLAY_CFG>, - <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>, + interconnects = <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>, <&mmss_noc MASTER_MDP_PORT1 &mc_virt SLAVE_EBI_CH0>; - interconnect-names = "notused", "mdp0-mem", "mdp1-mem"; + interconnect-names = "mdp0-mem", "mdp1-mem"; power-domains = <&dispcc MDSS_GDSC>; @@ -2356,7 +2355,7 @@ mdss: mdss@ae00000 { ranges; mdss_mdp: mdp@ae01000 { - compatible = "qcom,sdm845-dpu"; + compatible = "qcom,sm8250-dpu"; reg = <0 0x0ae01000 0 0x8f000>, <0 0x0aeb0000 0 0x2008>; reg-names = "mdp", "vbif"; @@ -2580,36 +2579,21 @@ opp-358000000 { dispcc: clock-controller@af00000 { compatible = "qcom,sm8250-dispcc"; - reg = <0 0x0af00000 0 0x20000>; - mmcx-supply = <&mmcx_reg>; + reg = <0 0x0af00000 0 0x10000>; clocks = <&rpmhcc RPMH_CXO_CLK>, <&dsi0_phy 0>, <&dsi0_phy 1>, <&dsi1_phy 0>, <&dsi1_phy 1>, - <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <&sleep_clk>; + <&dp_phy 0>, + <&dp_phy 1>; clock-names = "bi_tcxo", "dsi0_phy_pll_out_byteclk", "dsi0_phy_pll_out_dsiclk", "dsi1_phy_pll_out_byteclk", "dsi1_phy_pll_out_dsiclk", - "dp_link_clk_divsel_ten", - "dp_vco_divided_clk_src_mux", - "dptx1_phy_pll_link_clk", - "dptx1_phy_pll_vco_div_clk", - "dptx2_phy_pll_link_clk", - "dptx2_phy_pll_vco_div_clk", - "edp_phy_pll_link_clk", - "edp_phy_pll_vco_div_clk", - "sleep_clk"; + "dp_phy_pll_link_clk", + "dp_phy_pll_vco_div_clk"; #clock-cells = <1>; #reset-cells = <1>; #power-domain-cells = <1>; -- 2.26.1 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] arm64: dts: qcom: sm8250: fix display nodes 2021-02-11 18:09 ` [PATCH 2/2] arm64: dts: qcom: sm8250: fix display nodes Jonathan Marek @ 2021-02-11 20:05 ` Dmitry Baryshkov 2021-02-15 16:27 ` Jonathan Marek 2021-02-11 20:14 ` kernel test robot 1 sibling, 1 reply; 6+ messages in thread From: Dmitry Baryshkov @ 2021-02-11 20:05 UTC (permalink / raw) To: Jonathan Marek Cc: open list:DRM DRIVER FOR MSM ADRENO GPU, Andy Gross, Bjorn Andersson, Rob Herring, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, open list On Thu, 11 Feb 2021 at 21:11, Jonathan Marek <jonathan@marek.ca> wrote: > > Apply these fixes to the newly added sm8250 display ndoes > - Use sm8250 compatibles instead of sdm845 compatibles > - Remove "notused" interconnect (which apparently was blindly copied from > my old patches) > - Use dispcc node example from dt-bindings, removing clocks which aren't > documented or used by the driver and fixing the region size. > > Note: also removed the mmcx-supply for dispcc which wasn't documented when > it was added. I would have left it there but it is also breaking my > use-case (setting a lower power level than what the bootloader sets?). In our use case dispcc does not work w/o mmcx-supply. Compare this with the downstream kernel, which actively uses MMCX domain. > Fixes: 7c1dffd471b1 ("arm64: dts: qcom: sm8250.dtsi: add display system nodes") > Signed-off-by: Jonathan Marek <jonathan@marek.ca> > --- > arch/arm64/boot/dts/qcom/sm8250.dtsi | 34 ++++++++-------------------- > 1 file changed, 9 insertions(+), 25 deletions(-) > > diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi > index 947e1accae3a..20a3ff30e924 100644 > --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi > +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi > @@ -2323,14 +2323,13 @@ usb_2_dwc3: dwc3@a800000 { > }; > > mdss: mdss@ae00000 { > - compatible = "qcom,sdm845-mdss"; > + compatible = "qcom,sm8250-mdss"; > reg = <0 0x0ae00000 0 0x1000>; > reg-names = "mdss"; > > - interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_DISPLAY_CFG>, > - <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>, > + interconnects = <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>, > <&mmss_noc MASTER_MDP_PORT1 &mc_virt SLAVE_EBI_CH0>; > - interconnect-names = "notused", "mdp0-mem", "mdp1-mem"; > + interconnect-names = "mdp0-mem", "mdp1-mem"; > > power-domains = <&dispcc MDSS_GDSC>; > > @@ -2356,7 +2355,7 @@ mdss: mdss@ae00000 { > ranges; > > mdss_mdp: mdp@ae01000 { > - compatible = "qcom,sdm845-dpu"; > + compatible = "qcom,sm8250-dpu"; > reg = <0 0x0ae01000 0 0x8f000>, > <0 0x0aeb0000 0 0x2008>; > reg-names = "mdp", "vbif"; > @@ -2580,36 +2579,21 @@ opp-358000000 { > > dispcc: clock-controller@af00000 { > compatible = "qcom,sm8250-dispcc"; > - reg = <0 0x0af00000 0 0x20000>; > - mmcx-supply = <&mmcx_reg>; > + reg = <0 0x0af00000 0 0x10000>; > clocks = <&rpmhcc RPMH_CXO_CLK>, > <&dsi0_phy 0>, > <&dsi0_phy 1>, > <&dsi1_phy 0>, > <&dsi1_phy 1>, > - <0>, > - <0>, > - <0>, > - <0>, > - <0>, > - <0>, > - <0>, > - <0>, > - <&sleep_clk>; > + <&dp_phy 0>, > + <&dp_phy 1>; There is no dp_phy on sm8250 yet. > clock-names = "bi_tcxo", > "dsi0_phy_pll_out_byteclk", > "dsi0_phy_pll_out_dsiclk", > "dsi1_phy_pll_out_byteclk", > "dsi1_phy_pll_out_dsiclk", > - "dp_link_clk_divsel_ten", > - "dp_vco_divided_clk_src_mux", > - "dptx1_phy_pll_link_clk", > - "dptx1_phy_pll_vco_div_clk", > - "dptx2_phy_pll_link_clk", > - "dptx2_phy_pll_vco_div_clk", > - "edp_phy_pll_link_clk", > - "edp_phy_pll_vco_div_clk", > - "sleep_clk"; > + "dp_phy_pll_link_clk", > + "dp_phy_pll_vco_div_clk"; > #clock-cells = <1>; > #reset-cells = <1>; > #power-domain-cells = <1>; -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] arm64: dts: qcom: sm8250: fix display nodes 2021-02-11 20:05 ` Dmitry Baryshkov @ 2021-02-15 16:27 ` Jonathan Marek 0 siblings, 0 replies; 6+ messages in thread From: Jonathan Marek @ 2021-02-15 16:27 UTC (permalink / raw) To: Dmitry Baryshkov Cc: open list:DRM DRIVER FOR MSM ADRENO GPU, Andy Gross, Bjorn Andersson, Rob Herring, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, open list On 2/11/21 3:05 PM, Dmitry Baryshkov wrote: > On Thu, 11 Feb 2021 at 21:11, Jonathan Marek <jonathan@marek.ca> wrote: >> >> Apply these fixes to the newly added sm8250 display ndoes >> - Use sm8250 compatibles instead of sdm845 compatibles >> - Remove "notused" interconnect (which apparently was blindly copied from >> my old patches) >> - Use dispcc node example from dt-bindings, removing clocks which aren't >> documented or used by the driver and fixing the region size. >> >> Note: also removed the mmcx-supply for dispcc which wasn't documented when >> it was added. I would have left it there but it is also breaking my >> use-case (setting a lower power level than what the bootloader sets?). > > In our use case dispcc does not work w/o mmcx-supply. Compare this > with the downstream kernel, which actively uses MMCX domain. > I sent a v2/v3 leaving the mmcx-supply untouched (I can fix my problem by using rpmhpd_opp_nom in the mmcx-supply instead, so its not a problem with adding it to dispcc). But mmcx-supply still needs to be added to documentation. >> Fixes: 7c1dffd471b1 ("arm64: dts: qcom: sm8250.dtsi: add display system nodes") >> Signed-off-by: Jonathan Marek <jonathan@marek.ca> >> --- >> arch/arm64/boot/dts/qcom/sm8250.dtsi | 34 ++++++++-------------------- >> 1 file changed, 9 insertions(+), 25 deletions(-) >> >> diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi >> index 947e1accae3a..20a3ff30e924 100644 >> --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi >> +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi >> @@ -2323,14 +2323,13 @@ usb_2_dwc3: dwc3@a800000 { >> }; >> >> mdss: mdss@ae00000 { >> - compatible = "qcom,sdm845-mdss"; >> + compatible = "qcom,sm8250-mdss"; >> reg = <0 0x0ae00000 0 0x1000>; >> reg-names = "mdss"; >> >> - interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_DISPLAY_CFG>, >> - <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>, >> + interconnects = <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>, >> <&mmss_noc MASTER_MDP_PORT1 &mc_virt SLAVE_EBI_CH0>; >> - interconnect-names = "notused", "mdp0-mem", "mdp1-mem"; >> + interconnect-names = "mdp0-mem", "mdp1-mem"; >> >> power-domains = <&dispcc MDSS_GDSC>; >> >> @@ -2356,7 +2355,7 @@ mdss: mdss@ae00000 { >> ranges; >> >> mdss_mdp: mdp@ae01000 { >> - compatible = "qcom,sdm845-dpu"; >> + compatible = "qcom,sm8250-dpu"; >> reg = <0 0x0ae01000 0 0x8f000>, >> <0 0x0aeb0000 0 0x2008>; >> reg-names = "mdp", "vbif"; >> @@ -2580,36 +2579,21 @@ opp-358000000 { >> >> dispcc: clock-controller@af00000 { >> compatible = "qcom,sm8250-dispcc"; >> - reg = <0 0x0af00000 0 0x20000>; >> - mmcx-supply = <&mmcx_reg>; >> + reg = <0 0x0af00000 0 0x10000>; >> clocks = <&rpmhcc RPMH_CXO_CLK>, >> <&dsi0_phy 0>, >> <&dsi0_phy 1>, >> <&dsi1_phy 0>, >> <&dsi1_phy 1>, >> - <0>, >> - <0>, >> - <0>, >> - <0>, >> - <0>, >> - <0>, >> - <0>, >> - <0>, >> - <&sleep_clk>; >> + <&dp_phy 0>, >> + <&dp_phy 1>; > > There is no dp_phy on sm8250 yet. > >> clock-names = "bi_tcxo", >> "dsi0_phy_pll_out_byteclk", >> "dsi0_phy_pll_out_dsiclk", >> "dsi1_phy_pll_out_byteclk", >> "dsi1_phy_pll_out_dsiclk", >> - "dp_link_clk_divsel_ten", >> - "dp_vco_divided_clk_src_mux", >> - "dptx1_phy_pll_link_clk", >> - "dptx1_phy_pll_vco_div_clk", >> - "dptx2_phy_pll_link_clk", >> - "dptx2_phy_pll_vco_div_clk", >> - "edp_phy_pll_link_clk", >> - "edp_phy_pll_vco_div_clk", >> - "sleep_clk"; >> + "dp_phy_pll_link_clk", >> + "dp_phy_pll_vco_div_clk"; >> #clock-cells = <1>; >> #reset-cells = <1>; >> #power-domain-cells = <1>; > > > ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] arm64: dts: qcom: sm8250: fix display nodes 2021-02-11 18:09 ` [PATCH 2/2] arm64: dts: qcom: sm8250: fix display nodes Jonathan Marek 2021-02-11 20:05 ` Dmitry Baryshkov @ 2021-02-11 20:14 ` kernel test robot 1 sibling, 0 replies; 6+ messages in thread From: kernel test robot @ 2021-02-11 20:14 UTC (permalink / raw) To: Jonathan Marek, linux-arm-msm; +Cc: linux-kernel [-- Attachment #1: Type: text/plain, Size: 1862 bytes --] Hi Jonathan, Thank you for the patch! Yet something to improve: [auto build test ERROR on linux-next/master] [cannot apply to robh/for-next linux/master linus/master v5.11-rc7] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch] url: https://github.com/0day-ci/linux/commits/Jonathan-Marek/arm64-dts-qcom-sm8250-fix-display-nodes/20210212-021729 base: https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git 671176b0016c80b3943cb5387312c886aba3308d config: arm64-randconfig-r025-20210209 (attached as .config) compiler: clang version 12.0.0 (https://github.com/llvm/llvm-project c9439ca36342fb6013187d0a69aef92736951476) reproduce (this is a W=1 build): wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # install arm64 cross compiling tool for clang build # apt-get install binutils-aarch64-linux-gnu # https://github.com/0day-ci/linux/commit/5dfea33502f2797f0d94037a7987da8e8c9e2789 git remote add linux-review https://github.com/0day-ci/linux git fetch --no-tags linux-review Jonathan-Marek/arm64-dts-qcom-sm8250-fix-display-nodes/20210212-021729 git checkout 5dfea33502f2797f0d94037a7987da8e8c9e2789 # save the attached .config to linux build tree COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross ARCH=arm64 If you fix the issue, kindly add following tag as appropriate Reported-by: kernel test robot <lkp@intel.com> All errors (new ones prefixed by >>): >> ERROR: Input tree has errors, aborting (use -f to force output) --- 0-DAY CI Kernel Test Service, Intel Corporation https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org [-- Attachment #2: .config.gz --] [-- Type: application/gzip, Size: 29143 bytes --] ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2021-02-15 16:30 UTC | newest] Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2021-02-11 18:09 [PATCH 0/2] arm64: dts: qcom: sm8250: fix display nodes Jonathan Marek 2021-02-11 18:09 ` [PATCH 1/2] drm/msm: add compatibles for sm8150/sm8250 display Jonathan Marek 2021-02-11 18:09 ` [PATCH 2/2] arm64: dts: qcom: sm8250: fix display nodes Jonathan Marek 2021-02-11 20:05 ` Dmitry Baryshkov 2021-02-15 16:27 ` Jonathan Marek 2021-02-11 20:14 ` kernel test robot
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).