* [PATCH v6 0/2] add device Xiaomi Mi 6 (codename sagit) and board binding @ 2022-10-05 18:15 Dzmitry Sankouski 2022-10-05 18:15 ` [PATCH v6 1/2] dt-bindings: arm: add xiaomi,sagit board based on msm8998 chip Dzmitry Sankouski 2022-10-05 18:15 ` [PATCH v6 2/2] arm64: dts: qcom: sagit: add initial device tree for sagit Dzmitry Sankouski 0 siblings, 2 replies; 7+ messages in thread From: Dzmitry Sankouski @ 2022-10-05 18:15 UTC (permalink / raw) To: linux-kernel Cc: Dzmitry Sankouski, Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, open list:ARM/QUALCOMM SUPPORT, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS Add initial support for Xiaomi Mi 6 phone (codename sagit) Dzmitry Sankouski (2): dt-bindings: arm: add xiaomi,sagit board based on msm8998 chip arm64: dts: qcom: sagit: add initial device tree for sagit .../devicetree/bindings/arm/qcom.yaml | 1 + arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/msm8998-xiaomi-sagit.dts | 681 ++++++++++++++++++ arch/arm64/boot/dts/qcom/pm8998.dtsi | 8 + 4 files changed, 691 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts -- 2.30.2 ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v6 1/2] dt-bindings: arm: add xiaomi,sagit board based on msm8998 chip 2022-10-05 18:15 [PATCH v6 0/2] add device Xiaomi Mi 6 (codename sagit) and board binding Dzmitry Sankouski @ 2022-10-05 18:15 ` Dzmitry Sankouski 2022-10-06 7:03 ` Krzysztof Kozlowski 2022-10-05 18:15 ` [PATCH v6 2/2] arm64: dts: qcom: sagit: add initial device tree for sagit Dzmitry Sankouski 1 sibling, 1 reply; 7+ messages in thread From: Dzmitry Sankouski @ 2022-10-05 18:15 UTC (permalink / raw) To: linux-kernel Cc: Dzmitry Sankouski, Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, open list:ARM/QUALCOMM SUPPORT, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS Add xiaomi,sagit board (Xiaomi Mi 6) binding. Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com> --- Documentation/devicetree/bindings/arm/qcom.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml index fb1d00bcc847..294075bafb97 100644 --- a/Documentation/devicetree/bindings/arm/qcom.yaml +++ b/Documentation/devicetree/bindings/arm/qcom.yaml @@ -239,6 +239,7 @@ properties: - sony,xperia-lilac - sony,xperia-maple - sony,xperia-poplar + - xiaomi,sagit - const: qcom,msm8998 - items: -- 2.30.2 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: arm: add xiaomi,sagit board based on msm8998 chip 2022-10-05 18:15 ` [PATCH v6 1/2] dt-bindings: arm: add xiaomi,sagit board based on msm8998 chip Dzmitry Sankouski @ 2022-10-06 7:03 ` Krzysztof Kozlowski 0 siblings, 0 replies; 7+ messages in thread From: Krzysztof Kozlowski @ 2022-10-06 7:03 UTC (permalink / raw) To: Dzmitry Sankouski, linux-kernel Cc: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, open list:ARM/QUALCOMM SUPPORT, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS On 05/10/2022 20:15, Dzmitry Sankouski wrote: > Add xiaomi,sagit board (Xiaomi Mi 6) binding. > > Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com> > --- Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Best regards, Krzysztof ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v6 2/2] arm64: dts: qcom: sagit: add initial device tree for sagit 2022-10-05 18:15 [PATCH v6 0/2] add device Xiaomi Mi 6 (codename sagit) and board binding Dzmitry Sankouski 2022-10-05 18:15 ` [PATCH v6 1/2] dt-bindings: arm: add xiaomi,sagit board based on msm8998 chip Dzmitry Sankouski @ 2022-10-05 18:15 ` Dzmitry Sankouski 2022-10-05 18:30 ` Dzmitry Sankouski 2022-10-05 19:13 ` Dzmitry Sankouski 1 sibling, 2 replies; 7+ messages in thread From: Dzmitry Sankouski @ 2022-10-05 18:15 UTC (permalink / raw) To: linux-kernel Cc: Dzmitry Sankouski, Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, open list:ARM/QUALCOMM SUPPORT, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS New device support - Xiaomi Mi6 phone What works: - storage - usb - power regulators Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com> --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/msm8998-xiaomi-sagit.dts | 681 ++++++++++++++++++ arch/arm64/boot/dts/qcom/pm8998.dtsi | 8 + 3 files changed, 690 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 1d86a33de528..0460aabf1b59 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -46,6 +46,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-dumpling.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-lilac.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-maple.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-poplar.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8998-xiaomi-sagit.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb diff --git a/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts new file mode 100644 index 000000000000..e44f6a745a2c --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts @@ -0,0 +1,681 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Xiaomi Mi 6 (sagit) device tree source based on msm8998-mtp.dtsi + * + * Copyright (c) 2022, The Linux Foundation. All rights reserved. + * Copyright (c) 2022, Degdag Mohamed <degdagmohamed@gmail.com> + * Copyright (c) 2022, Dzmitry Sankouski <dsankouski@gmail.com> + */ + +/dts-v1/; + +#include "msm8998.dtsi" +#include "pm8005.dtsi" +#include "pm8998.dtsi" +#include "pmi8998.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> + +/* + * Delete following upstream (msm8998.dtsi) reserved + * memory mappings which are different in this device. + */ +/delete-node/ &mpss_mem; +/delete-node/ &venus_mem; +/delete-node/ &mba_mem; +/delete-node/ &slpi_mem; +/delete-node/ &ipa_fw_mem; +/delete-node/ &ipa_gsi_mem; +/delete-node/ &gpu_mem; +/delete-node/ &wlan_msa_mem; + +/ { + model = "Xiaomi Mi 6"; + compatible = "xiaomi,sagit", "qcom,msm8998"; + chassis-type = "handset"; + /* Required for bootloader to select correct board */ + qcom,board-id = <30 0>; + + reserved-memory { + /* + * The following memory regions on downstream are "dynamically allocated" + * but given the same addresses every time. Hard code them as these addresses + * are where the Xiaomi signed firmware expects them to be. + */ + ipa_fws_region: ipa@f7800000 { + compatible = "shared-dma-pool"; + reg = <0x0 0xf7800000 0x0 0x5000>; + no-map; + }; + + zap_shader_region: gpu@f7900000 { + compatible = "shared-dma-pool"; + reg = <0x0 0xf7900000 0x0 0x2000>; + no-map; + }; + + mpss_mem: memory@8d000000 { + reg = <0x0 0x8d000000 0x0 0x7000000>; + no-map; + }; + + venus_mem: memory@94000000 { + reg = <0x0 0x94000000 0x0 0x500000>; + no-map; + }; + + mba_mem: memory@94500000 { + reg = <0x0 0x94500000 0x0 0x200000>; + no-map; + }; + + slpi_mem: memory@94700000 { + reg = <0x0 0x94700000 0x0 0x10000>; + no-map; + }; + + ipa_fw_mem: memory@95600000 { + reg = <0x0 0x95600000 0x0 0x10000>; + no-map; + }; + + ipa_gsi_mem: memory@95610000 { + reg = <0x0 0x95610000 0x0 0x5000>; + no-map; + }; + + gpu_mem: memory@95615000 { + reg = <0x0 0x95615000 0x0 0x100000>; + no-map; + }; + + wlan_msa_mem: memory@95715000 { + reg = <0x0 0x95715000 0x0 0x100000>; + no-map; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + label = "Volume buttons"; + autorepeat; + + pinctrl-names = "default"; + pinctrl-0 = <&vol_up_key_default>; + + key-vol-up { + label = "Volume up"; + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + debounce-interval = <15>; + wakeup-source; + }; + }; + + gpio-hall-sensor { + compatible = "gpio-keys"; + label = "Hall effect sensor"; + + pinctrl-names = "default"; + pinctrl-0 = <&hall_sensor_default_state>; + + event-hall-sensor { + label = "Hall Effect Sensor"; + gpios = <&tlmm 124 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + linux,can-disable; + wakeup-source; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + regulator-always-on; + regulator-boot-on; + }; + + disp_vddts_vreg: disp-vddts-regulator { + compatible = "regulator-fixed"; + regulator-name = "disp-vddts-regulator"; + gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; +}; + +&blsp1_i2c5 { + pinctrl-names = "default", "sleep"; + + touchscreen@20 { + compatible = "syna,rmi4-i2c"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&tlmm>; + interrupts = <125 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&ts_active_state>; + pinctrl-1 = <&ts_int_suspend_state &ts_reset_suspend_state>; + + vdd-supply = <&disp_vddts_vreg>; + vio-supply = <&vreg_l6a_1p8>; + + syna,reset-delay-ms = <20>; + syna,startup-delay-ms = <20>; + + rmi4-f01@1 { + reg = <0x01>; + syna,nosleep-mode = <1>; + }; + + rmi4-f12@12 { + reg = <0x12>; + touchscreen-x-mm = <64>; + touchscreen-y-mm = <114>; + syna,sensor-type = <1>; + syna,rezero-wait-ms = <20>; + }; + + rmi4-f1a@1a { + reg = <0x1a>; + syna,codes = <KEY_BACK KEY_APPSELECT>; + }; + }; + status = "okay"; +}; + +&blsp1_i2c5_sleep { + /delete-property/ bias-pull-up; + bias-disable; +}; + +&blsp1_uart3 { + bluetooth { + compatible = "qcom,wcn3990-bt"; + + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + }; + status = "okay"; +}; + +&blsp1_uart3_on { + rx { + /delete-property/ bias-disable; + /* + * Configure a pull-up on 46 (RX). This is needed to + * avoid garbage data when the TX pin of the Bluetooth + * module is in tri-state (module powered off or not + * driving the signal yet). + */ + bias-pull-up; + }; + + cts { + /delete-property/ bias-disable; + /* + * Configure a pull-down on 47 (CTS) to match the pull + * of the Bluetooth module. + */ + bias-pull-down; + }; +}; + +&blsp2_uart1 { + status = "okay"; +}; + +&pm8005_regulators { + compatible = "qcom,pm8005-regulators"; + + vdd_s1-supply = <&vph_pwr>; + + pm8005_s1: s1 { /* VDD_GFX supply */ + regulator-min-microvolt = <524000>; + regulator-max-microvolt = <1100000>; + regulator-enable-ramp-delay = <500>; + + /* hack until we rig up the gpu consumer */ + regulator-always-on; + }; +}; + +&pm8998_gpio { + vol_up_key_default: vol-up-key-default-state { + pins = "gpio6"; + function = "normal"; + bias-pull-up; + input-enable; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + }; + + audio_mclk_pin: audio-mclk-pin-active-state { + pins = "gpio13"; + function = "func2"; + power-source = <0>; + }; +}; + +&qusb2phy { + vdda-pll-supply = <&vreg_l12a_1p8>; + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; + status = "okay"; +}; + +&rpm_requests { + regulators-0 { + compatible = "qcom,rpm-pm8998-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + vdd_s7-supply = <&vph_pwr>; + vdd_s8-supply = <&vph_pwr>; + vdd_s9-supply = <&vph_pwr>; + vdd_s10-supply = <&vph_pwr>; + vdd_s11-supply = <&vph_pwr>; + vdd_s12-supply = <&vph_pwr>; + vdd_s13-supply = <&vph_pwr>; + vdd_l1_l27-supply = <&vreg_s7a_1p025>; + vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>; + vdd_l3_l11-supply = <&vreg_s7a_1p025>; + vdd_l4_l5-supply = <&vreg_s7a_1p025>; + vdd_l6-supply = <&vreg_s5a_2p04>; + vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>; + vdd_l9-supply = <&vreg_bob>; + vdd_l10_l23_l25-supply = <&vreg_bob>; + vdd_l13_l19_l21-supply = <&vreg_bob>; + vdd_l16_l28-supply = <&vreg_bob>; + vdd_l18_l22-supply = <&vreg_bob>; + vdd_l20_l24-supply = <&vreg_bob>; + vdd_l26-supply = <&vreg_s3a_1p35>; + vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>; + + vreg_s3a_1p35: s3 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + + vreg_s4a_1p8: s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + }; + + vreg_s5a_2p04: s5 { + regulator-min-microvolt = <1904000>; + regulator-max-microvolt = <2040000>; + }; + + vreg_s7a_1p025: s7 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1028000>; + }; + + vreg_l1a_0p875: l1 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + }; + + vreg_l2a_1p2: l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vreg_l3a_1p0: l3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_l5a_0p8: l5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + }; + + vreg_l6a_1p8: l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l7a_1p8: l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l8a_1p2: l8 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vreg_l9a_1p8: l9 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <2960000>; + }; + + vreg_l10a_1p8: l10 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <2960000>; + }; + + vreg_l11a_1p0: l11 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_l12a_1p8: l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l13a_2p95: l13 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <2960000>; + }; + + vreg_l14a_1p8: l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l15a_1p8: l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l16a_2p7: l16 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + }; + + vreg_l17a_1p3: l17 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + }; + + vreg_l18a_2p7: l18 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + }; + + vreg_l19a_3p0: l19 { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + }; + + vreg_l20a_2p95: l20 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-allow-set-load; + }; + + vreg_l21a_2p95: l21 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-system-load = <800000>; + regulator-allow-set-load; + }; + + vreg_l22a_2p85: l22 { + regulator-min-microvolt = <2864000>; + regulator-max-microvolt = <2864000>; + }; + + vreg_l23a_3p3: l23 { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3312000>; + }; + + vreg_l24a_3p075: l24 { + regulator-min-microvolt = <3088000>; + regulator-max-microvolt = <3088000>; + }; + + vreg_l25a_3p3: l25 { + regulator-min-microvolt = <3104000>; + regulator-max-microvolt = <3312000>; + }; + + vreg_l26a_1p2: l26 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-allow-set-load; + }; + + vreg_l28_3p0: l28 { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + }; + + vreg_lvs1a_1p8: lvs1 { }; + + vreg_lvs2a_1p8: lvs2 { }; + }; + + regulators-1 { + compatible = "qcom,rpm-pmi8998-regulators"; + + vdd_bob-supply = <&vph_pwr>; + + vreg_bob: bob { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3600000>; + }; + }; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>, <81 4>; + + cci1_default_state: cci1-default-state { + pins = "gpio19", "gpio20"; + function = "cci_i2c"; + bias-disable; + drive-strength = <2>; + }; + + cdc_reset_n_state: cdc-reset-n-state { + pins = "gpio64"; + function = "gpio"; + bias-pull-down; + drive-strength = <16>; + output-high; + }; + + hall_sensor_default_state: hall-sensor-default-state { + pins = "gpio124"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + input-enable; + }; + + mdss_dsi_active_state: mdss-dsi-active-state { + pins = "gpio94"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + + mdss_dsi_suspend_state: mdss-dsi-suspend-state { + pins = "gpio94"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + + mdss_te_active_state: mdss-te-active-state { + pins = "gpio10"; + function = "mdp_vsync_a"; + drive-strength = <2>; + bias-pull-down; + }; + + mdss_te_suspend_state: mdss-te-suspend-state { + pins = "gpio10"; + function = "mdp_vsync_a"; + drive-strength = <2>; + bias-pull-down; + }; + + msm_mclk0_active_state: msm-mclk0-active-state { + pins = "gpio13"; + function = "cam_mclk"; + drive-strength = <2>; + bias-disable; + }; + + msm_mclk0_suspend_state: msm-mclk0-suspend-state { + pins = "gpio13"; + function = "cam_mclk"; + drive-strength = <2>; + bias-pull-down; + }; + + msm_mclk1_active_state: msm-mclk1-active-state { + pins = "gpio14"; + function = "cam_mclk"; + drive-strength = <2>; + bias-disable; + }; + + msm_mclk1_suspend_state: msm-mclk1-suspend-state { + pins = "gpio14"; + function = "cam_mclk"; + drive-strength = <2>; + bias-pull-down; + }; + + nfc_int_active_state: nfc-int-active-state { + pins = "gpio92"; + function = "gpio"; + drive-strength = <6>; + bias-pull-up; + }; + + nfc_int_suspend_state: nfc-int-suspend-state { + pins = "gpio92"; + function = "gpio"; + drive-strength = <6>; + bias-pull-up; + }; + + nfc_enable_active_state: nfc-enable-active-state { + pins = "gpio12", "gpio116"; + function = "gpio"; + drive-strength = <6>; + bias-pull-up; + }; + + nfc_enable_suspend_state: nfc-enable-suspend-state { + pins = "gpio12", "gpio116"; + function = "gpio"; + drive-strength = <6>; + bias-disable; + }; + + ts_active_state: ts-active-state { + pins = "gpio89", "gpio125"; + function = "gpio"; + drive-strength = <16>; + bias-pull-up; + input-enable; + }; + + ts_int_suspend_state: ts-int-suspend-state { + pins = "gpio125"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + ts_reset_suspend_state: ts-reset-suspend-state { + pins = "gpio89"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wcd_int_n_state: wcd-int-n-state { + pins = "gpio54"; + function = "gpio"; + bias-pull-down; + drive-strength = <2>; + input-enable; + }; + + wsa_leftspk_pwr_n_state: wsa-leftspk-pwr-n-state { + pins = "gpio65"; + function = "gpio"; + bias-disable; + drive-strength = <2>; + output-low; + }; + + wsa_rightspk_pwr_n_state: wsa-rightspk-pwr-n-state { + pins = "gpio66"; + function = "gpio"; + bias-disable; + drive-strength = <2>; + output-low; + }; +}; + +&pm8998_resin { + linux,code = <KEY_VOLUMEDOWN>; +}; + +&ufshc { + vcc-supply = <&vreg_l20a_2p95>; + vccq-supply = <&vreg_l26a_1p2>; + vccq2-supply = <&vreg_s4a_1p8>; + vcc-max-microamp = <750000>; + vccq-max-microamp = <560000>; + vccq2-max-microamp = <750000>; + status = "okay"; +}; + +&ufsphy { + vdda-phy-supply = <&vreg_l1a_0p875>; + vdda-pll-supply = <&vreg_l2a_1p2>; + vddp-ref-clk-supply = <&vreg_l26a_1p2>; + status = "okay"; +}; + +&usb3 { + /* Disable USB3 clock requirement as the device only supports USB2 */ + qcom,select-utmi-as-pipe-clk; + status = "okay"; +}; + +&usb3_dwc3 { + /* Drop the unused USB 3 PHY */ + phys = <&qusb2phy>; + phy-names = "usb2-phy"; + + /* Fastest mode for USB 2 */ + maximum-speed = "high-speed"; + + /* Force to peripheral until we can switch modes */ + dr_mode = "peripheral"; +}; + +&wifi { + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi index d09f2954b6f9..7929fa64e1ef 100644 --- a/arch/arm64/boot/dts/qcom/pm8998.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi @@ -52,6 +52,14 @@ pm8998_pwrkey: pwrkey { bias-pull-up; linux,code = <KEY_POWER>; }; + + pm8998_resin: resin { + compatible = "qcom,pm8941-resin"; + bias-pull-up; + interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + status = "disabled"; + }; }; pm8998_temp: temp-alarm@2400 { -- 2.30.2 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v6 2/2] arm64: dts: qcom: sagit: add initial device tree for sagit 2022-10-05 18:15 ` [PATCH v6 2/2] arm64: dts: qcom: sagit: add initial device tree for sagit Dzmitry Sankouski @ 2022-10-05 18:30 ` Dzmitry Sankouski 2022-10-07 19:34 ` Konrad Dybcio 2022-10-05 19:13 ` Dzmitry Sankouski 1 sibling, 1 reply; 7+ messages in thread From: Dzmitry Sankouski @ 2022-10-05 18:30 UTC (permalink / raw) To: linux-kernel Cc: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, open list:ARM/QUALCOMM SUPPORT, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS Here is changelogs: Changes for v2: - remove memory nodes before redefining - add board compatible to schema - remove board msm-id, add chassis type - remove common dtsi - move resin to pm8998 dtsi file - dts formatting - unsupported properties removed - add copyright - rebase on latest master(6.0.0-rc6) Changes for v3: - regulators nodes renamed to match pattern 'regulators-[01]' - duplicate cci1-default node deleted - add state suffix to '.*(active|suspend|default)' pinctrl - rebase on latest master(6.0.0) Changes for v4: - fix dts compilation errors(rename pinctrl label usages) Changes for v5: - use pm8005_regulators label Changes for v6: - add state suffix to all pinctrl - move status nodes to last position - disable resin node by default - move the debounce param to pm8998.dtsi file - place this patch after dt-binding patch ср, 5 окт. 2022 г. в 21:15, Dzmitry Sankouski <dsankouski@gmail.com>: > > New device support - Xiaomi Mi6 phone > > What works: > - storage > - usb > - power regulators > > Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../boot/dts/qcom/msm8998-xiaomi-sagit.dts | 681 ++++++++++++++++++ > arch/arm64/boot/dts/qcom/pm8998.dtsi | 8 + > 3 files changed, 690 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 1d86a33de528..0460aabf1b59 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -46,6 +46,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-dumpling.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-lilac.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-maple.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-poplar.dtb > +dtb-$(CONFIG_ARCH_QCOM) += msm8998-xiaomi-sagit.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb > dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb > diff --git a/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts > new file mode 100644 > index 000000000000..e44f6a745a2c > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts > @@ -0,0 +1,681 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Xiaomi Mi 6 (sagit) device tree source based on msm8998-mtp.dtsi > + * > + * Copyright (c) 2022, The Linux Foundation. All rights reserved. > + * Copyright (c) 2022, Degdag Mohamed <degdagmohamed@gmail.com> > + * Copyright (c) 2022, Dzmitry Sankouski <dsankouski@gmail.com> > + */ > + > +/dts-v1/; > + > +#include "msm8998.dtsi" > +#include "pm8005.dtsi" > +#include "pm8998.dtsi" > +#include "pmi8998.dtsi" > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> > + > +/* > + * Delete following upstream (msm8998.dtsi) reserved > + * memory mappings which are different in this device. > + */ > +/delete-node/ &mpss_mem; > +/delete-node/ &venus_mem; > +/delete-node/ &mba_mem; > +/delete-node/ &slpi_mem; > +/delete-node/ &ipa_fw_mem; > +/delete-node/ &ipa_gsi_mem; > +/delete-node/ &gpu_mem; > +/delete-node/ &wlan_msa_mem; > + > +/ { > + model = "Xiaomi Mi 6"; > + compatible = "xiaomi,sagit", "qcom,msm8998"; > + chassis-type = "handset"; > + /* Required for bootloader to select correct board */ > + qcom,board-id = <30 0>; > + > + reserved-memory { > + /* > + * The following memory regions on downstream are "dynamically allocated" > + * but given the same addresses every time. Hard code them as these addresses > + * are where the Xiaomi signed firmware expects them to be. > + */ > + ipa_fws_region: ipa@f7800000 { > + compatible = "shared-dma-pool"; > + reg = <0x0 0xf7800000 0x0 0x5000>; > + no-map; > + }; > + > + zap_shader_region: gpu@f7900000 { > + compatible = "shared-dma-pool"; > + reg = <0x0 0xf7900000 0x0 0x2000>; > + no-map; > + }; > + > + mpss_mem: memory@8d000000 { > + reg = <0x0 0x8d000000 0x0 0x7000000>; > + no-map; > + }; > + > + venus_mem: memory@94000000 { > + reg = <0x0 0x94000000 0x0 0x500000>; > + no-map; > + }; > + > + mba_mem: memory@94500000 { > + reg = <0x0 0x94500000 0x0 0x200000>; > + no-map; > + }; > + > + slpi_mem: memory@94700000 { > + reg = <0x0 0x94700000 0x0 0x10000>; > + no-map; > + }; > + > + ipa_fw_mem: memory@95600000 { > + reg = <0x0 0x95600000 0x0 0x10000>; > + no-map; > + }; > + > + ipa_gsi_mem: memory@95610000 { > + reg = <0x0 0x95610000 0x0 0x5000>; > + no-map; > + }; > + > + gpu_mem: memory@95615000 { > + reg = <0x0 0x95615000 0x0 0x100000>; > + no-map; > + }; > + > + wlan_msa_mem: memory@95715000 { > + reg = <0x0 0x95715000 0x0 0x100000>; > + no-map; > + }; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + label = "Volume buttons"; > + autorepeat; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&vol_up_key_default>; > + > + key-vol-up { > + label = "Volume up"; > + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEUP>; > + debounce-interval = <15>; > + wakeup-source; > + }; > + }; > + > + gpio-hall-sensor { > + compatible = "gpio-keys"; > + label = "Hall effect sensor"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&hall_sensor_default_state>; > + > + event-hall-sensor { > + label = "Hall Effect Sensor"; > + gpios = <&tlmm 124 GPIO_ACTIVE_LOW>; > + linux,input-type = <EV_SW>; > + linux,code = <SW_LID>; > + linux,can-disable; > + wakeup-source; > + }; > + }; > + > + vph_pwr: vph-pwr-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vph_pwr"; > + regulator-min-microvolt = <3700000>; > + regulator-max-microvolt = <3700000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + disp_vddts_vreg: disp-vddts-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "disp-vddts-regulator"; > + gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-boot-on; > + }; > +}; > + > +&blsp1_i2c5 { > + pinctrl-names = "default", "sleep"; > + > + touchscreen@20 { > + compatible = "syna,rmi4-i2c"; > + reg = <0x20>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + interrupt-parent = <&tlmm>; > + interrupts = <125 IRQ_TYPE_EDGE_FALLING>; > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&ts_active_state>; > + pinctrl-1 = <&ts_int_suspend_state &ts_reset_suspend_state>; > + > + vdd-supply = <&disp_vddts_vreg>; > + vio-supply = <&vreg_l6a_1p8>; > + > + syna,reset-delay-ms = <20>; > + syna,startup-delay-ms = <20>; > + > + rmi4-f01@1 { > + reg = <0x01>; > + syna,nosleep-mode = <1>; > + }; > + > + rmi4-f12@12 { > + reg = <0x12>; > + touchscreen-x-mm = <64>; > + touchscreen-y-mm = <114>; > + syna,sensor-type = <1>; > + syna,rezero-wait-ms = <20>; > + }; > + > + rmi4-f1a@1a { > + reg = <0x1a>; > + syna,codes = <KEY_BACK KEY_APPSELECT>; > + }; > + }; > + status = "okay"; > +}; > + > +&blsp1_i2c5_sleep { > + /delete-property/ bias-pull-up; > + bias-disable; > +}; > + > +&blsp1_uart3 { > + bluetooth { > + compatible = "qcom,wcn3990-bt"; > + > + vddio-supply = <&vreg_s4a_1p8>; > + vddxo-supply = <&vreg_l7a_1p8>; > + vddrf-supply = <&vreg_l17a_1p3>; > + vddch0-supply = <&vreg_l25a_3p3>; > + max-speed = <3200000>; > + }; > + status = "okay"; > +}; > + > +&blsp1_uart3_on { > + rx { > + /delete-property/ bias-disable; > + /* > + * Configure a pull-up on 46 (RX). This is needed to > + * avoid garbage data when the TX pin of the Bluetooth > + * module is in tri-state (module powered off or not > + * driving the signal yet). > + */ > + bias-pull-up; > + }; > + > + cts { > + /delete-property/ bias-disable; > + /* > + * Configure a pull-down on 47 (CTS) to match the pull > + * of the Bluetooth module. > + */ > + bias-pull-down; > + }; > +}; > + > +&blsp2_uart1 { > + status = "okay"; > +}; > + > +&pm8005_regulators { > + compatible = "qcom,pm8005-regulators"; > + > + vdd_s1-supply = <&vph_pwr>; > + > + pm8005_s1: s1 { /* VDD_GFX supply */ > + regulator-min-microvolt = <524000>; > + regulator-max-microvolt = <1100000>; > + regulator-enable-ramp-delay = <500>; > + > + /* hack until we rig up the gpu consumer */ > + regulator-always-on; > + }; > +}; > + > +&pm8998_gpio { > + vol_up_key_default: vol-up-key-default-state { > + pins = "gpio6"; > + function = "normal"; > + bias-pull-up; > + input-enable; > + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; > + }; > + > + audio_mclk_pin: audio-mclk-pin-active-state { > + pins = "gpio13"; > + function = "func2"; > + power-source = <0>; > + }; > +}; > + > +&qusb2phy { > + vdda-pll-supply = <&vreg_l12a_1p8>; > + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; > + status = "okay"; > +}; > + > +&rpm_requests { > + regulators-0 { > + compatible = "qcom,rpm-pm8998-regulators"; > + > + vdd_s1-supply = <&vph_pwr>; > + vdd_s2-supply = <&vph_pwr>; > + vdd_s3-supply = <&vph_pwr>; > + vdd_s4-supply = <&vph_pwr>; > + vdd_s5-supply = <&vph_pwr>; > + vdd_s6-supply = <&vph_pwr>; > + vdd_s7-supply = <&vph_pwr>; > + vdd_s8-supply = <&vph_pwr>; > + vdd_s9-supply = <&vph_pwr>; > + vdd_s10-supply = <&vph_pwr>; > + vdd_s11-supply = <&vph_pwr>; > + vdd_s12-supply = <&vph_pwr>; > + vdd_s13-supply = <&vph_pwr>; > + vdd_l1_l27-supply = <&vreg_s7a_1p025>; > + vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>; > + vdd_l3_l11-supply = <&vreg_s7a_1p025>; > + vdd_l4_l5-supply = <&vreg_s7a_1p025>; > + vdd_l6-supply = <&vreg_s5a_2p04>; > + vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>; > + vdd_l9-supply = <&vreg_bob>; > + vdd_l10_l23_l25-supply = <&vreg_bob>; > + vdd_l13_l19_l21-supply = <&vreg_bob>; > + vdd_l16_l28-supply = <&vreg_bob>; > + vdd_l18_l22-supply = <&vreg_bob>; > + vdd_l20_l24-supply = <&vreg_bob>; > + vdd_l26-supply = <&vreg_s3a_1p35>; > + vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>; > + > + vreg_s3a_1p35: s3 { > + regulator-min-microvolt = <1352000>; > + regulator-max-microvolt = <1352000>; > + }; > + > + vreg_s4a_1p8: s4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-allow-set-load; > + }; > + > + vreg_s5a_2p04: s5 { > + regulator-min-microvolt = <1904000>; > + regulator-max-microvolt = <2040000>; > + }; > + > + vreg_s7a_1p025: s7 { > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <1028000>; > + }; > + > + vreg_l1a_0p875: l1 { > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <880000>; > + }; > + > + vreg_l2a_1p2: l2 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + }; > + > + vreg_l3a_1p0: l3 { > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + }; > + > + vreg_l5a_0p8: l5 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <800000>; > + }; > + > + vreg_l6a_1p8: l6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + vreg_l7a_1p8: l7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + vreg_l8a_1p2: l8 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + }; > + > + vreg_l9a_1p8: l9 { > + regulator-min-microvolt = <1808000>; > + regulator-max-microvolt = <2960000>; > + }; > + > + vreg_l10a_1p8: l10 { > + regulator-min-microvolt = <1808000>; > + regulator-max-microvolt = <2960000>; > + }; > + > + vreg_l11a_1p0: l11 { > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + }; > + > + vreg_l12a_1p8: l12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + vreg_l13a_2p95: l13 { > + regulator-min-microvolt = <1808000>; > + regulator-max-microvolt = <2960000>; > + }; > + > + vreg_l14a_1p8: l14 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + vreg_l15a_1p8: l15 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + vreg_l16a_2p7: l16 { > + regulator-min-microvolt = <2704000>; > + regulator-max-microvolt = <2704000>; > + }; > + > + vreg_l17a_1p3: l17 { > + regulator-min-microvolt = <1304000>; > + regulator-max-microvolt = <1304000>; > + }; > + > + vreg_l18a_2p7: l18 { > + regulator-min-microvolt = <2704000>; > + regulator-max-microvolt = <2704000>; > + }; > + > + vreg_l19a_3p0: l19 { > + regulator-min-microvolt = <3008000>; > + regulator-max-microvolt = <3008000>; > + }; > + > + vreg_l20a_2p95: l20 { > + regulator-min-microvolt = <2960000>; > + regulator-max-microvolt = <2960000>; > + regulator-allow-set-load; > + }; > + > + vreg_l21a_2p95: l21 { > + regulator-min-microvolt = <2960000>; > + regulator-max-microvolt = <2960000>; > + regulator-system-load = <800000>; > + regulator-allow-set-load; > + }; > + > + vreg_l22a_2p85: l22 { > + regulator-min-microvolt = <2864000>; > + regulator-max-microvolt = <2864000>; > + }; > + > + vreg_l23a_3p3: l23 { > + regulator-min-microvolt = <3312000>; > + regulator-max-microvolt = <3312000>; > + }; > + > + vreg_l24a_3p075: l24 { > + regulator-min-microvolt = <3088000>; > + regulator-max-microvolt = <3088000>; > + }; > + > + vreg_l25a_3p3: l25 { > + regulator-min-microvolt = <3104000>; > + regulator-max-microvolt = <3312000>; > + }; > + > + vreg_l26a_1p2: l26 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-allow-set-load; > + }; > + > + vreg_l28_3p0: l28 { > + regulator-min-microvolt = <3008000>; > + regulator-max-microvolt = <3008000>; > + }; > + > + vreg_lvs1a_1p8: lvs1 { }; > + > + vreg_lvs2a_1p8: lvs2 { }; > + }; > + > + regulators-1 { > + compatible = "qcom,rpm-pmi8998-regulators"; > + > + vdd_bob-supply = <&vph_pwr>; > + > + vreg_bob: bob { > + regulator-min-microvolt = <3312000>; > + regulator-max-microvolt = <3600000>; > + }; > + }; > +}; > + > +&tlmm { > + gpio-reserved-ranges = <0 4>, <81 4>; > + > + cci1_default_state: cci1-default-state { > + pins = "gpio19", "gpio20"; > + function = "cci_i2c"; > + bias-disable; > + drive-strength = <2>; > + }; > + > + cdc_reset_n_state: cdc-reset-n-state { > + pins = "gpio64"; > + function = "gpio"; > + bias-pull-down; > + drive-strength = <16>; > + output-high; > + }; > + > + hall_sensor_default_state: hall-sensor-default-state { > + pins = "gpio124"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + input-enable; > + }; > + > + mdss_dsi_active_state: mdss-dsi-active-state { > + pins = "gpio94"; > + function = "gpio"; > + drive-strength = <8>; > + bias-disable; > + }; > + > + mdss_dsi_suspend_state: mdss-dsi-suspend-state { > + pins = "gpio94"; > + function = "gpio"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > + mdss_te_active_state: mdss-te-active-state { > + pins = "gpio10"; > + function = "mdp_vsync_a"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > + mdss_te_suspend_state: mdss-te-suspend-state { > + pins = "gpio10"; > + function = "mdp_vsync_a"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > + msm_mclk0_active_state: msm-mclk0-active-state { > + pins = "gpio13"; > + function = "cam_mclk"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + msm_mclk0_suspend_state: msm-mclk0-suspend-state { > + pins = "gpio13"; > + function = "cam_mclk"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > + msm_mclk1_active_state: msm-mclk1-active-state { > + pins = "gpio14"; > + function = "cam_mclk"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + msm_mclk1_suspend_state: msm-mclk1-suspend-state { > + pins = "gpio14"; > + function = "cam_mclk"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > + nfc_int_active_state: nfc-int-active-state { > + pins = "gpio92"; > + function = "gpio"; > + drive-strength = <6>; > + bias-pull-up; > + }; > + > + nfc_int_suspend_state: nfc-int-suspend-state { > + pins = "gpio92"; > + function = "gpio"; > + drive-strength = <6>; > + bias-pull-up; > + }; > + > + nfc_enable_active_state: nfc-enable-active-state { > + pins = "gpio12", "gpio116"; > + function = "gpio"; > + drive-strength = <6>; > + bias-pull-up; > + }; > + > + nfc_enable_suspend_state: nfc-enable-suspend-state { > + pins = "gpio12", "gpio116"; > + function = "gpio"; > + drive-strength = <6>; > + bias-disable; > + }; > + > + ts_active_state: ts-active-state { > + pins = "gpio89", "gpio125"; > + function = "gpio"; > + drive-strength = <16>; > + bias-pull-up; > + input-enable; > + }; > + > + ts_int_suspend_state: ts-int-suspend-state { > + pins = "gpio125"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + ts_reset_suspend_state: ts-reset-suspend-state { > + pins = "gpio89"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + wcd_int_n_state: wcd-int-n-state { > + pins = "gpio54"; > + function = "gpio"; > + bias-pull-down; > + drive-strength = <2>; > + input-enable; > + }; > + > + wsa_leftspk_pwr_n_state: wsa-leftspk-pwr-n-state { > + pins = "gpio65"; > + function = "gpio"; > + bias-disable; > + drive-strength = <2>; > + output-low; > + }; > + > + wsa_rightspk_pwr_n_state: wsa-rightspk-pwr-n-state { > + pins = "gpio66"; > + function = "gpio"; > + bias-disable; > + drive-strength = <2>; > + output-low; > + }; > +}; > + > +&pm8998_resin { > + linux,code = <KEY_VOLUMEDOWN>; > +}; > + > +&ufshc { > + vcc-supply = <&vreg_l20a_2p95>; > + vccq-supply = <&vreg_l26a_1p2>; > + vccq2-supply = <&vreg_s4a_1p8>; > + vcc-max-microamp = <750000>; > + vccq-max-microamp = <560000>; > + vccq2-max-microamp = <750000>; > + status = "okay"; > +}; > + > +&ufsphy { > + vdda-phy-supply = <&vreg_l1a_0p875>; > + vdda-pll-supply = <&vreg_l2a_1p2>; > + vddp-ref-clk-supply = <&vreg_l26a_1p2>; > + status = "okay"; > +}; > + > +&usb3 { > + /* Disable USB3 clock requirement as the device only supports USB2 */ > + qcom,select-utmi-as-pipe-clk; > + status = "okay"; > +}; > + > +&usb3_dwc3 { > + /* Drop the unused USB 3 PHY */ > + phys = <&qusb2phy>; > + phy-names = "usb2-phy"; > + > + /* Fastest mode for USB 2 */ > + maximum-speed = "high-speed"; > + > + /* Force to peripheral until we can switch modes */ > + dr_mode = "peripheral"; > +}; > + > +&wifi { > + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; > + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; > + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; > + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; > + status = "okay"; > +}; > diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi > index d09f2954b6f9..7929fa64e1ef 100644 > --- a/arch/arm64/boot/dts/qcom/pm8998.dtsi > +++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi > @@ -52,6 +52,14 @@ pm8998_pwrkey: pwrkey { > bias-pull-up; > linux,code = <KEY_POWER>; > }; > + > + pm8998_resin: resin { > + compatible = "qcom,pm8941-resin"; > + bias-pull-up; > + interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>; > + debounce = <15625>; > + status = "disabled"; > + }; > }; > > pm8998_temp: temp-alarm@2400 { > -- > 2.30.2 > ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v6 2/2] arm64: dts: qcom: sagit: add initial device tree for sagit 2022-10-05 18:30 ` Dzmitry Sankouski @ 2022-10-07 19:34 ` Konrad Dybcio 0 siblings, 0 replies; 7+ messages in thread From: Konrad Dybcio @ 2022-10-07 19:34 UTC (permalink / raw) To: Dzmitry Sankouski, linux-kernel Cc: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski, open list:ARM/QUALCOMM SUPPORT, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS On 5.10.2022 20:30, Dzmitry Sankouski wrote: > Here is changelogs: > > Changes for v2: > - remove memory nodes before redefining > - add board compatible to schema > - remove board msm-id, add chassis type > - remove common dtsi > - move resin to pm8998 dtsi file > - dts formatting > - unsupported properties removed > - add copyright > - rebase on latest master(6.0.0-rc6) > Changes for v3: > - regulators nodes renamed to match pattern 'regulators-[01]' > - duplicate cci1-default node deleted > - add state suffix to '.*(active|suspend|default)' pinctrl > - rebase on latest master(6.0.0) > Changes for v4: > - fix dts compilation errors(rename pinctrl label usages) > Changes for v5: > - use pm8005_regulators label > Changes for v6: > - add state suffix to all pinctrl > - move status nodes to last position > - disable resin node by default > - move the debounce param to pm8998.dtsi file > - place this patch after dt-binding patch > > > ср, 5 окт. 2022 г. в 21:15, Dzmitry Sankouski <dsankouski@gmail.com>: >> >> New device support - Xiaomi Mi6 phone >> >> What works: >> - storage >> - usb >> - power regulators >> >> Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com> >> --- >> arch/arm64/boot/dts/qcom/Makefile | 1 + >> .../boot/dts/qcom/msm8998-xiaomi-sagit.dts | 681 ++++++++++++++++++ >> arch/arm64/boot/dts/qcom/pm8998.dtsi | 8 + >> 3 files changed, 690 insertions(+) >> create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts >> >> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile >> index 1d86a33de528..0460aabf1b59 100644 >> --- a/arch/arm64/boot/dts/qcom/Makefile >> +++ b/arch/arm64/boot/dts/qcom/Makefile >> @@ -46,6 +46,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-dumpling.dtb >> dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-lilac.dtb >> dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-maple.dtb >> dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-poplar.dtb >> +dtb-$(CONFIG_ARCH_QCOM) += msm8998-xiaomi-sagit.dtb >> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb >> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb >> dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb >> diff --git a/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts >> new file mode 100644 >> index 000000000000..e44f6a745a2c >> --- /dev/null >> +++ b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts >> @@ -0,0 +1,681 @@ >> +// SPDX-License-Identifier: BSD-3-Clause >> +/* >> + * Xiaomi Mi 6 (sagit) device tree source based on msm8998-mtp.dtsi >> + * >> + * Copyright (c) 2022, The Linux Foundation. All rights reserved. >> + * Copyright (c) 2022, Degdag Mohamed <degdagmohamed@gmail.com> >> + * Copyright (c) 2022, Dzmitry Sankouski <dsankouski@gmail.com> >> + */ >> + >> +/dts-v1/; >> + >> +#include "msm8998.dtsi" >> +#include "pm8005.dtsi" >> +#include "pm8998.dtsi" >> +#include "pmi8998.dtsi" >> +#include <dt-bindings/input/input.h> >> +#include <dt-bindings/leds/common.h> >> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> >> + >> +/* >> + * Delete following upstream (msm8998.dtsi) reserved >> + * memory mappings which are different in this device. >> + */ >> +/delete-node/ &mpss_mem; >> +/delete-node/ &venus_mem; >> +/delete-node/ &mba_mem; >> +/delete-node/ &slpi_mem; >> +/delete-node/ &ipa_fw_mem; >> +/delete-node/ &ipa_gsi_mem; >> +/delete-node/ &gpu_mem; >> +/delete-node/ &wlan_msa_mem; >> + >> +/ { >> + model = "Xiaomi Mi 6"; >> + compatible = "xiaomi,sagit", "qcom,msm8998"; >> + chassis-type = "handset"; >> + /* Required for bootloader to select correct board */ >> + qcom,board-id = <30 0>; >> + >> + reserved-memory { >> + /* >> + * The following memory regions on downstream are "dynamically allocated" >> + * but given the same addresses every time. Hard code them as these addresses >> + * are where the Xiaomi signed firmware expects them to be. >> + */ >> + ipa_fws_region: ipa@f7800000 { memory@ >> + compatible = "shared-dma-pool"; >> + reg = <0x0 0xf7800000 0x0 0x5000>; >> + no-map; >> + }; >> + >> + zap_shader_region: gpu@f7900000 { memory@ >> + compatible = "shared-dma-pool"; >> + reg = <0x0 0xf7900000 0x0 0x2000>; >> + no-map; >> + }; >> + >> + mpss_mem: memory@8d000000 { >> + reg = <0x0 0x8d000000 0x0 0x7000000>; >> + no-map; >> + }; >> + >> + venus_mem: memory@94000000 { >> + reg = <0x0 0x94000000 0x0 0x500000>; >> + no-map; >> + }; >> + >> + mba_mem: memory@94500000 { >> + reg = <0x0 0x94500000 0x0 0x200000>; >> + no-map; >> + }; >> + >> + slpi_mem: memory@94700000 { >> + reg = <0x0 0x94700000 0x0 0x10000>; >> + no-map; >> + }; >> + >> + ipa_fw_mem: memory@95600000 { >> + reg = <0x0 0x95600000 0x0 0x10000>; >> + no-map; >> + }; >> + >> + ipa_gsi_mem: memory@95610000 { >> + reg = <0x0 0x95610000 0x0 0x5000>; >> + no-map; >> + }; >> + >> + gpu_mem: memory@95615000 { >> + reg = <0x0 0x95615000 0x0 0x100000>; >> + no-map; >> + }; >> + >> + wlan_msa_mem: memory@95715000 { >> + reg = <0x0 0x95715000 0x0 0x100000>; >> + no-map; >> + }; >> + }; >> + >> + gpio-keys { >> + compatible = "gpio-keys"; >> + label = "Volume buttons"; >> + autorepeat; >> + >> + pinctrl-names = "default"; >> + pinctrl-0 = <&vol_up_key_default>; >> + >> + key-vol-up { >> + label = "Volume up"; >> + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; >> + linux,code = <KEY_VOLUMEUP>; >> + debounce-interval = <15>; >> + wakeup-source; >> + }; >> + }; >> + >> + gpio-hall-sensor { >> + compatible = "gpio-keys"; >> + label = "Hall effect sensor"; >> + >> + pinctrl-names = "default"; >> + pinctrl-0 = <&hall_sensor_default_state>; >> + >> + event-hall-sensor { >> + label = "Hall Effect Sensor"; >> + gpios = <&tlmm 124 GPIO_ACTIVE_LOW>; >> + linux,input-type = <EV_SW>; >> + linux,code = <SW_LID>; >> + linux,can-disable; >> + wakeup-source; >> + }; >> + }; >> + >> + vph_pwr: vph-pwr-regulator { >> + compatible = "regulator-fixed"; >> + regulator-name = "vph_pwr"; >> + regulator-min-microvolt = <3700000>; >> + regulator-max-microvolt = <3700000>; >> + regulator-always-on; >> + regulator-boot-on; >> + }; >> + >> + disp_vddts_vreg: disp-vddts-regulator { >> + compatible = "regulator-fixed"; >> + regulator-name = "disp-vddts-regulator"; >> + gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>; >> + enable-active-high; >> + regulator-boot-on; >> + }; >> +}; >> + >> +&blsp1_i2c5 { >> + pinctrl-names = "default", "sleep"; >> + >> + touchscreen@20 { >> + compatible = "syna,rmi4-i2c"; >> + reg = <0x20>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + interrupt-parent = <&tlmm>; >> + interrupts = <125 IRQ_TYPE_EDGE_FALLING>; >> + >> + pinctrl-names = "default", "sleep"; >> + pinctrl-0 = <&ts_active_state>; >> + pinctrl-1 = <&ts_int_suspend_state &ts_reset_suspend_state>; >> + >> + vdd-supply = <&disp_vddts_vreg>; >> + vio-supply = <&vreg_l6a_1p8>; >> + >> + syna,reset-delay-ms = <20>; >> + syna,startup-delay-ms = <20>; >> + >> + rmi4-f01@1 { >> + reg = <0x01>; >> + syna,nosleep-mode = <1>; >> + }; >> + >> + rmi4-f12@12 { >> + reg = <0x12>; >> + touchscreen-x-mm = <64>; >> + touchscreen-y-mm = <114>; >> + syna,sensor-type = <1>; >> + syna,rezero-wait-ms = <20>; >> + }; >> + >> + rmi4-f1a@1a { >> + reg = <0x1a>; >> + syna,codes = <KEY_BACK KEY_APPSELECT>; >> + }; >> + }; >> + status = "okay"; This generates a DTC warning. Status should be the last *property*. However, properties must precede subnodes. This applies to all occurences. >> +}; >> + >> +&blsp1_i2c5_sleep { >> + /delete-property/ bias-pull-up; >> + bias-disable; >> +}; >> + >> +&blsp1_uart3 { >> + bluetooth { >> + compatible = "qcom,wcn3990-bt"; >> + >> + vddio-supply = <&vreg_s4a_1p8>; >> + vddxo-supply = <&vreg_l7a_1p8>; >> + vddrf-supply = <&vreg_l17a_1p3>; >> + vddch0-supply = <&vreg_l25a_3p3>; >> + max-speed = <3200000>; >> + }; >> + status = "okay"; >> +}; >> + >> +&blsp1_uart3_on { >> + rx { >> + /delete-property/ bias-disable; >> + /* >> + * Configure a pull-up on 46 (RX). This is needed to >> + * avoid garbage data when the TX pin of the Bluetooth >> + * module is in tri-state (module powered off or not >> + * driving the signal yet). >> + */ >> + bias-pull-up; >> + }; >> + >> + cts { >> + /delete-property/ bias-disable; >> + /* >> + * Configure a pull-down on 47 (CTS) to match the pull >> + * of the Bluetooth module. >> + */ >> + bias-pull-down; >> + }; >> +}; >> + >> +&blsp2_uart1 { >> + status = "okay"; >> +}; >> + >> +&pm8005_regulators { >> + compatible = "qcom,pm8005-regulators"; >> + >> + vdd_s1-supply = <&vph_pwr>; >> + >> + pm8005_s1: s1 { /* VDD_GFX supply */ >> + regulator-min-microvolt = <524000>; >> + regulator-max-microvolt = <1100000>; >> + regulator-enable-ramp-delay = <500>; >> + >> + /* hack until we rig up the gpu consumer */ >> + regulator-always-on; >> + }; >> +}; >> + >> +&pm8998_gpio { >> + vol_up_key_default: vol-up-key-default-state { >> + pins = "gpio6"; >> + function = "normal"; >> + bias-pull-up; >> + input-enable; >> + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; >> + }; >> + >> + audio_mclk_pin: audio-mclk-pin-active-state { >> + pins = "gpio13"; >> + function = "func2"; >> + power-source = <0>; >> + }; >> +}; >> + >> +&qusb2phy { >> + vdda-pll-supply = <&vreg_l12a_1p8>; >> + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; >> + status = "okay"; >> +}; >> + >> +&rpm_requests { >> + regulators-0 { >> + compatible = "qcom,rpm-pm8998-regulators"; >> + >> + vdd_s1-supply = <&vph_pwr>; >> + vdd_s2-supply = <&vph_pwr>; >> + vdd_s3-supply = <&vph_pwr>; >> + vdd_s4-supply = <&vph_pwr>; >> + vdd_s5-supply = <&vph_pwr>; >> + vdd_s6-supply = <&vph_pwr>; >> + vdd_s7-supply = <&vph_pwr>; >> + vdd_s8-supply = <&vph_pwr>; >> + vdd_s9-supply = <&vph_pwr>; >> + vdd_s10-supply = <&vph_pwr>; >> + vdd_s11-supply = <&vph_pwr>; >> + vdd_s12-supply = <&vph_pwr>; >> + vdd_s13-supply = <&vph_pwr>; >> + vdd_l1_l27-supply = <&vreg_s7a_1p025>; >> + vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>; >> + vdd_l3_l11-supply = <&vreg_s7a_1p025>; >> + vdd_l4_l5-supply = <&vreg_s7a_1p025>; >> + vdd_l6-supply = <&vreg_s5a_2p04>; >> + vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>; >> + vdd_l9-supply = <&vreg_bob>; >> + vdd_l10_l23_l25-supply = <&vreg_bob>; >> + vdd_l13_l19_l21-supply = <&vreg_bob>; >> + vdd_l16_l28-supply = <&vreg_bob>; >> + vdd_l18_l22-supply = <&vreg_bob>; >> + vdd_l20_l24-supply = <&vreg_bob>; >> + vdd_l26-supply = <&vreg_s3a_1p35>; >> + vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>; >> + >> + vreg_s3a_1p35: s3 { >> + regulator-min-microvolt = <1352000>; >> + regulator-max-microvolt = <1352000>; >> + }; >> + >> + vreg_s4a_1p8: s4 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-allow-set-load; >> + }; >> + >> + vreg_s5a_2p04: s5 { >> + regulator-min-microvolt = <1904000>; >> + regulator-max-microvolt = <2040000>; >> + }; >> + >> + vreg_s7a_1p025: s7 { >> + regulator-min-microvolt = <900000>; >> + regulator-max-microvolt = <1028000>; >> + }; >> + >> + vreg_l1a_0p875: l1 { >> + regulator-min-microvolt = <880000>; >> + regulator-max-microvolt = <880000>; >> + }; >> + >> + vreg_l2a_1p2: l2 { >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + }; >> + >> + vreg_l3a_1p0: l3 { >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1000000>; >> + }; >> + >> + vreg_l5a_0p8: l5 { >> + regulator-min-microvolt = <800000>; >> + regulator-max-microvolt = <800000>; >> + }; >> + >> + vreg_l6a_1p8: l6 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + }; >> + >> + vreg_l7a_1p8: l7 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + }; >> + >> + vreg_l8a_1p2: l8 { >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + }; >> + >> + vreg_l9a_1p8: l9 { >> + regulator-min-microvolt = <1808000>; >> + regulator-max-microvolt = <2960000>; >> + }; >> + >> + vreg_l10a_1p8: l10 { >> + regulator-min-microvolt = <1808000>; >> + regulator-max-microvolt = <2960000>; >> + }; >> + >> + vreg_l11a_1p0: l11 { >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1000000>; >> + }; >> + >> + vreg_l12a_1p8: l12 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + }; >> + >> + vreg_l13a_2p95: l13 { >> + regulator-min-microvolt = <1808000>; >> + regulator-max-microvolt = <2960000>; >> + }; >> + >> + vreg_l14a_1p8: l14 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + }; >> + >> + vreg_l15a_1p8: l15 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + }; >> + >> + vreg_l16a_2p7: l16 { >> + regulator-min-microvolt = <2704000>; >> + regulator-max-microvolt = <2704000>; >> + }; >> + >> + vreg_l17a_1p3: l17 { >> + regulator-min-microvolt = <1304000>; >> + regulator-max-microvolt = <1304000>; >> + }; >> + >> + vreg_l18a_2p7: l18 { >> + regulator-min-microvolt = <2704000>; >> + regulator-max-microvolt = <2704000>; >> + }; >> + >> + vreg_l19a_3p0: l19 { >> + regulator-min-microvolt = <3008000>; >> + regulator-max-microvolt = <3008000>; >> + }; >> + >> + vreg_l20a_2p95: l20 { >> + regulator-min-microvolt = <2960000>; >> + regulator-max-microvolt = <2960000>; >> + regulator-allow-set-load; >> + }; >> + >> + vreg_l21a_2p95: l21 { >> + regulator-min-microvolt = <2960000>; >> + regulator-max-microvolt = <2960000>; >> + regulator-system-load = <800000>; >> + regulator-allow-set-load; >> + }; >> + >> + vreg_l22a_2p85: l22 { >> + regulator-min-microvolt = <2864000>; >> + regulator-max-microvolt = <2864000>; >> + }; >> + >> + vreg_l23a_3p3: l23 { >> + regulator-min-microvolt = <3312000>; >> + regulator-max-microvolt = <3312000>; >> + }; >> + >> + vreg_l24a_3p075: l24 { >> + regulator-min-microvolt = <3088000>; >> + regulator-max-microvolt = <3088000>; >> + }; >> + >> + vreg_l25a_3p3: l25 { >> + regulator-min-microvolt = <3104000>; >> + regulator-max-microvolt = <3312000>; >> + }; >> + >> + vreg_l26a_1p2: l26 { >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-allow-set-load; >> + }; >> + >> + vreg_l28_3p0: l28 { >> + regulator-min-microvolt = <3008000>; >> + regulator-max-microvolt = <3008000>; >> + }; >> + >> + vreg_lvs1a_1p8: lvs1 { }; >> + >> + vreg_lvs2a_1p8: lvs2 { }; >> + }; >> + >> + regulators-1 { >> + compatible = "qcom,rpm-pmi8998-regulators"; >> + >> + vdd_bob-supply = <&vph_pwr>; >> + >> + vreg_bob: bob { >> + regulator-min-microvolt = <3312000>; >> + regulator-max-microvolt = <3600000>; >> + }; >> + }; >> +}; >> + >> +&tlmm { >> + gpio-reserved-ranges = <0 4>, <81 4>; >> + >> + cci1_default_state: cci1-default-state { >> + pins = "gpio19", "gpio20"; >> + function = "cci_i2c"; >> + bias-disable; >> + drive-strength = <2>; >> + }; >> + >> + cdc_reset_n_state: cdc-reset-n-state { >> + pins = "gpio64"; >> + function = "gpio"; >> + bias-pull-down; >> + drive-strength = <16>; >> + output-high; >> + }; >> + >> + hall_sensor_default_state: hall-sensor-default-state { >> + pins = "gpio124"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-disable; >> + input-enable; >> + }; >> + >> + mdss_dsi_active_state: mdss-dsi-active-state { >> + pins = "gpio94"; >> + function = "gpio"; >> + drive-strength = <8>; >> + bias-disable; >> + }; >> + >> + mdss_dsi_suspend_state: mdss-dsi-suspend-state { >> + pins = "gpio94"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-pull-down; >> + }; >> + >> + mdss_te_active_state: mdss-te-active-state { >> + pins = "gpio10"; >> + function = "mdp_vsync_a"; >> + drive-strength = <2>; >> + bias-pull-down; >> + }; >> + >> + mdss_te_suspend_state: mdss-te-suspend-state { >> + pins = "gpio10"; >> + function = "mdp_vsync_a"; >> + drive-strength = <2>; >> + bias-pull-down; >> + }; >> + >> + msm_mclk0_active_state: msm-mclk0-active-state { >> + pins = "gpio13"; >> + function = "cam_mclk"; >> + drive-strength = <2>; >> + bias-disable; >> + }; >> + >> + msm_mclk0_suspend_state: msm-mclk0-suspend-state { >> + pins = "gpio13"; >> + function = "cam_mclk"; >> + drive-strength = <2>; >> + bias-pull-down; >> + }; >> + >> + msm_mclk1_active_state: msm-mclk1-active-state { >> + pins = "gpio14"; >> + function = "cam_mclk"; >> + drive-strength = <2>; >> + bias-disable; >> + }; >> + >> + msm_mclk1_suspend_state: msm-mclk1-suspend-state { >> + pins = "gpio14"; >> + function = "cam_mclk"; >> + drive-strength = <2>; >> + bias-pull-down; >> + }; >> + >> + nfc_int_active_state: nfc-int-active-state { >> + pins = "gpio92"; >> + function = "gpio"; >> + drive-strength = <6>; >> + bias-pull-up; >> + }; >> + >> + nfc_int_suspend_state: nfc-int-suspend-state { >> + pins = "gpio92"; >> + function = "gpio"; >> + drive-strength = <6>; >> + bias-pull-up; >> + }; >> + >> + nfc_enable_active_state: nfc-enable-active-state { >> + pins = "gpio12", "gpio116"; >> + function = "gpio"; >> + drive-strength = <6>; >> + bias-pull-up; >> + }; >> + >> + nfc_enable_suspend_state: nfc-enable-suspend-state { >> + pins = "gpio12", "gpio116"; >> + function = "gpio"; >> + drive-strength = <6>; >> + bias-disable; >> + }; >> + >> + ts_active_state: ts-active-state { >> + pins = "gpio89", "gpio125"; >> + function = "gpio"; >> + drive-strength = <16>; >> + bias-pull-up; >> + input-enable; >> + }; >> + >> + ts_int_suspend_state: ts-int-suspend-state { >> + pins = "gpio125"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-disable; >> + }; >> + >> + ts_reset_suspend_state: ts-reset-suspend-state { >> + pins = "gpio89"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-disable; >> + }; >> + >> + wcd_int_n_state: wcd-int-n-state { >> + pins = "gpio54"; >> + function = "gpio"; >> + bias-pull-down; >> + drive-strength = <2>; >> + input-enable; >> + }; >> + >> + wsa_leftspk_pwr_n_state: wsa-leftspk-pwr-n-state { >> + pins = "gpio65"; >> + function = "gpio"; >> + bias-disable; >> + drive-strength = <2>; >> + output-low; >> + }; >> + >> + wsa_rightspk_pwr_n_state: wsa-rightspk-pwr-n-state { >> + pins = "gpio66"; >> + function = "gpio"; >> + bias-disable; >> + drive-strength = <2>; >> + output-low; >> + }; >> +}; >> + >> +&pm8998_resin { >> + linux,code = <KEY_VOLUMEDOWN>; >> +}; You forgot to enable it. Konrad >> + >> +&ufshc { >> + vcc-supply = <&vreg_l20a_2p95>; >> + vccq-supply = <&vreg_l26a_1p2>; >> + vccq2-supply = <&vreg_s4a_1p8>; >> + vcc-max-microamp = <750000>; >> + vccq-max-microamp = <560000>; >> + vccq2-max-microamp = <750000>; >> + status = "okay"; >> +}; >> + >> +&ufsphy { >> + vdda-phy-supply = <&vreg_l1a_0p875>; >> + vdda-pll-supply = <&vreg_l2a_1p2>; >> + vddp-ref-clk-supply = <&vreg_l26a_1p2>; >> + status = "okay"; >> +}; >> + >> +&usb3 { >> + /* Disable USB3 clock requirement as the device only supports USB2 */ >> + qcom,select-utmi-as-pipe-clk; >> + status = "okay"; >> +}; >> + >> +&usb3_dwc3 { >> + /* Drop the unused USB 3 PHY */ >> + phys = <&qusb2phy>; >> + phy-names = "usb2-phy"; >> + >> + /* Fastest mode for USB 2 */ >> + maximum-speed = "high-speed"; >> + >> + /* Force to peripheral until we can switch modes */ >> + dr_mode = "peripheral"; >> +}; >> + >> +&wifi { >> + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; >> + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; >> + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; >> + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; >> + status = "okay"; >> +}; >> diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi >> index d09f2954b6f9..7929fa64e1ef 100644 >> --- a/arch/arm64/boot/dts/qcom/pm8998.dtsi >> +++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi >> @@ -52,6 +52,14 @@ pm8998_pwrkey: pwrkey { >> bias-pull-up; >> linux,code = <KEY_POWER>; >> }; >> + >> + pm8998_resin: resin { >> + compatible = "qcom,pm8941-resin"; >> + bias-pull-up; >> + interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>; >> + debounce = <15625>; >> + status = "disabled"; >> + }; >> }; >> >> pm8998_temp: temp-alarm@2400 { >> -- >> 2.30.2 >> ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v6 2/2] arm64: dts: qcom: sagit: add initial device tree for sagit 2022-10-05 18:15 ` [PATCH v6 2/2] arm64: dts: qcom: sagit: add initial device tree for sagit Dzmitry Sankouski 2022-10-05 18:30 ` Dzmitry Sankouski @ 2022-10-05 19:13 ` Dzmitry Sankouski 1 sibling, 0 replies; 7+ messages in thread From: Dzmitry Sankouski @ 2022-10-05 19:13 UTC (permalink / raw) To: linux-kernel Cc: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, open list:ARM/QUALCOMM SUPPORT, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS compilation fails for this patch version, please, heed on to version 7 series ср, 5 окт. 2022 г. в 21:15, Dzmitry Sankouski <dsankouski@gmail.com>: > > New device support - Xiaomi Mi6 phone > > What works: > - storage > - usb > - power regulators > > Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../boot/dts/qcom/msm8998-xiaomi-sagit.dts | 681 ++++++++++++++++++ > arch/arm64/boot/dts/qcom/pm8998.dtsi | 8 + > 3 files changed, 690 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 1d86a33de528..0460aabf1b59 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -46,6 +46,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-dumpling.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-lilac.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-maple.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-poplar.dtb > +dtb-$(CONFIG_ARCH_QCOM) += msm8998-xiaomi-sagit.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb > dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb > diff --git a/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts > new file mode 100644 > index 000000000000..e44f6a745a2c > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts > @@ -0,0 +1,681 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Xiaomi Mi 6 (sagit) device tree source based on msm8998-mtp.dtsi > + * > + * Copyright (c) 2022, The Linux Foundation. All rights reserved. > + * Copyright (c) 2022, Degdag Mohamed <degdagmohamed@gmail.com> > + * Copyright (c) 2022, Dzmitry Sankouski <dsankouski@gmail.com> > + */ > + > +/dts-v1/; > + > +#include "msm8998.dtsi" > +#include "pm8005.dtsi" > +#include "pm8998.dtsi" > +#include "pmi8998.dtsi" > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> > + > +/* > + * Delete following upstream (msm8998.dtsi) reserved > + * memory mappings which are different in this device. > + */ > +/delete-node/ &mpss_mem; > +/delete-node/ &venus_mem; > +/delete-node/ &mba_mem; > +/delete-node/ &slpi_mem; > +/delete-node/ &ipa_fw_mem; > +/delete-node/ &ipa_gsi_mem; > +/delete-node/ &gpu_mem; > +/delete-node/ &wlan_msa_mem; > + > +/ { > + model = "Xiaomi Mi 6"; > + compatible = "xiaomi,sagit", "qcom,msm8998"; > + chassis-type = "handset"; > + /* Required for bootloader to select correct board */ > + qcom,board-id = <30 0>; > + > + reserved-memory { > + /* > + * The following memory regions on downstream are "dynamically allocated" > + * but given the same addresses every time. Hard code them as these addresses > + * are where the Xiaomi signed firmware expects them to be. > + */ > + ipa_fws_region: ipa@f7800000 { > + compatible = "shared-dma-pool"; > + reg = <0x0 0xf7800000 0x0 0x5000>; > + no-map; > + }; > + > + zap_shader_region: gpu@f7900000 { > + compatible = "shared-dma-pool"; > + reg = <0x0 0xf7900000 0x0 0x2000>; > + no-map; > + }; > + > + mpss_mem: memory@8d000000 { > + reg = <0x0 0x8d000000 0x0 0x7000000>; > + no-map; > + }; > + > + venus_mem: memory@94000000 { > + reg = <0x0 0x94000000 0x0 0x500000>; > + no-map; > + }; > + > + mba_mem: memory@94500000 { > + reg = <0x0 0x94500000 0x0 0x200000>; > + no-map; > + }; > + > + slpi_mem: memory@94700000 { > + reg = <0x0 0x94700000 0x0 0x10000>; > + no-map; > + }; > + > + ipa_fw_mem: memory@95600000 { > + reg = <0x0 0x95600000 0x0 0x10000>; > + no-map; > + }; > + > + ipa_gsi_mem: memory@95610000 { > + reg = <0x0 0x95610000 0x0 0x5000>; > + no-map; > + }; > + > + gpu_mem: memory@95615000 { > + reg = <0x0 0x95615000 0x0 0x100000>; > + no-map; > + }; > + > + wlan_msa_mem: memory@95715000 { > + reg = <0x0 0x95715000 0x0 0x100000>; > + no-map; > + }; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + label = "Volume buttons"; > + autorepeat; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&vol_up_key_default>; > + > + key-vol-up { > + label = "Volume up"; > + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEUP>; > + debounce-interval = <15>; > + wakeup-source; > + }; > + }; > + > + gpio-hall-sensor { > + compatible = "gpio-keys"; > + label = "Hall effect sensor"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&hall_sensor_default_state>; > + > + event-hall-sensor { > + label = "Hall Effect Sensor"; > + gpios = <&tlmm 124 GPIO_ACTIVE_LOW>; > + linux,input-type = <EV_SW>; > + linux,code = <SW_LID>; > + linux,can-disable; > + wakeup-source; > + }; > + }; > + > + vph_pwr: vph-pwr-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vph_pwr"; > + regulator-min-microvolt = <3700000>; > + regulator-max-microvolt = <3700000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + disp_vddts_vreg: disp-vddts-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "disp-vddts-regulator"; > + gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-boot-on; > + }; > +}; > + > +&blsp1_i2c5 { > + pinctrl-names = "default", "sleep"; > + > + touchscreen@20 { > + compatible = "syna,rmi4-i2c"; > + reg = <0x20>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + interrupt-parent = <&tlmm>; > + interrupts = <125 IRQ_TYPE_EDGE_FALLING>; > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&ts_active_state>; > + pinctrl-1 = <&ts_int_suspend_state &ts_reset_suspend_state>; > + > + vdd-supply = <&disp_vddts_vreg>; > + vio-supply = <&vreg_l6a_1p8>; > + > + syna,reset-delay-ms = <20>; > + syna,startup-delay-ms = <20>; > + > + rmi4-f01@1 { > + reg = <0x01>; > + syna,nosleep-mode = <1>; > + }; > + > + rmi4-f12@12 { > + reg = <0x12>; > + touchscreen-x-mm = <64>; > + touchscreen-y-mm = <114>; > + syna,sensor-type = <1>; > + syna,rezero-wait-ms = <20>; > + }; > + > + rmi4-f1a@1a { > + reg = <0x1a>; > + syna,codes = <KEY_BACK KEY_APPSELECT>; > + }; > + }; > + status = "okay"; > +}; > + > +&blsp1_i2c5_sleep { > + /delete-property/ bias-pull-up; > + bias-disable; > +}; > + > +&blsp1_uart3 { > + bluetooth { > + compatible = "qcom,wcn3990-bt"; > + > + vddio-supply = <&vreg_s4a_1p8>; > + vddxo-supply = <&vreg_l7a_1p8>; > + vddrf-supply = <&vreg_l17a_1p3>; > + vddch0-supply = <&vreg_l25a_3p3>; > + max-speed = <3200000>; > + }; > + status = "okay"; > +}; > + > +&blsp1_uart3_on { > + rx { > + /delete-property/ bias-disable; > + /* > + * Configure a pull-up on 46 (RX). This is needed to > + * avoid garbage data when the TX pin of the Bluetooth > + * module is in tri-state (module powered off or not > + * driving the signal yet). > + */ > + bias-pull-up; > + }; > + > + cts { > + /delete-property/ bias-disable; > + /* > + * Configure a pull-down on 47 (CTS) to match the pull > + * of the Bluetooth module. > + */ > + bias-pull-down; > + }; > +}; > + > +&blsp2_uart1 { > + status = "okay"; > +}; > + > +&pm8005_regulators { > + compatible = "qcom,pm8005-regulators"; > + > + vdd_s1-supply = <&vph_pwr>; > + > + pm8005_s1: s1 { /* VDD_GFX supply */ > + regulator-min-microvolt = <524000>; > + regulator-max-microvolt = <1100000>; > + regulator-enable-ramp-delay = <500>; > + > + /* hack until we rig up the gpu consumer */ > + regulator-always-on; > + }; > +}; > + > +&pm8998_gpio { > + vol_up_key_default: vol-up-key-default-state { > + pins = "gpio6"; > + function = "normal"; > + bias-pull-up; > + input-enable; > + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; > + }; > + > + audio_mclk_pin: audio-mclk-pin-active-state { > + pins = "gpio13"; > + function = "func2"; > + power-source = <0>; > + }; > +}; > + > +&qusb2phy { > + vdda-pll-supply = <&vreg_l12a_1p8>; > + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; > + status = "okay"; > +}; > + > +&rpm_requests { > + regulators-0 { > + compatible = "qcom,rpm-pm8998-regulators"; > + > + vdd_s1-supply = <&vph_pwr>; > + vdd_s2-supply = <&vph_pwr>; > + vdd_s3-supply = <&vph_pwr>; > + vdd_s4-supply = <&vph_pwr>; > + vdd_s5-supply = <&vph_pwr>; > + vdd_s6-supply = <&vph_pwr>; > + vdd_s7-supply = <&vph_pwr>; > + vdd_s8-supply = <&vph_pwr>; > + vdd_s9-supply = <&vph_pwr>; > + vdd_s10-supply = <&vph_pwr>; > + vdd_s11-supply = <&vph_pwr>; > + vdd_s12-supply = <&vph_pwr>; > + vdd_s13-supply = <&vph_pwr>; > + vdd_l1_l27-supply = <&vreg_s7a_1p025>; > + vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>; > + vdd_l3_l11-supply = <&vreg_s7a_1p025>; > + vdd_l4_l5-supply = <&vreg_s7a_1p025>; > + vdd_l6-supply = <&vreg_s5a_2p04>; > + vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>; > + vdd_l9-supply = <&vreg_bob>; > + vdd_l10_l23_l25-supply = <&vreg_bob>; > + vdd_l13_l19_l21-supply = <&vreg_bob>; > + vdd_l16_l28-supply = <&vreg_bob>; > + vdd_l18_l22-supply = <&vreg_bob>; > + vdd_l20_l24-supply = <&vreg_bob>; > + vdd_l26-supply = <&vreg_s3a_1p35>; > + vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>; > + > + vreg_s3a_1p35: s3 { > + regulator-min-microvolt = <1352000>; > + regulator-max-microvolt = <1352000>; > + }; > + > + vreg_s4a_1p8: s4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-allow-set-load; > + }; > + > + vreg_s5a_2p04: s5 { > + regulator-min-microvolt = <1904000>; > + regulator-max-microvolt = <2040000>; > + }; > + > + vreg_s7a_1p025: s7 { > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <1028000>; > + }; > + > + vreg_l1a_0p875: l1 { > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <880000>; > + }; > + > + vreg_l2a_1p2: l2 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + }; > + > + vreg_l3a_1p0: l3 { > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + }; > + > + vreg_l5a_0p8: l5 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <800000>; > + }; > + > + vreg_l6a_1p8: l6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + vreg_l7a_1p8: l7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + vreg_l8a_1p2: l8 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + }; > + > + vreg_l9a_1p8: l9 { > + regulator-min-microvolt = <1808000>; > + regulator-max-microvolt = <2960000>; > + }; > + > + vreg_l10a_1p8: l10 { > + regulator-min-microvolt = <1808000>; > + regulator-max-microvolt = <2960000>; > + }; > + > + vreg_l11a_1p0: l11 { > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + }; > + > + vreg_l12a_1p8: l12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + vreg_l13a_2p95: l13 { > + regulator-min-microvolt = <1808000>; > + regulator-max-microvolt = <2960000>; > + }; > + > + vreg_l14a_1p8: l14 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + vreg_l15a_1p8: l15 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + vreg_l16a_2p7: l16 { > + regulator-min-microvolt = <2704000>; > + regulator-max-microvolt = <2704000>; > + }; > + > + vreg_l17a_1p3: l17 { > + regulator-min-microvolt = <1304000>; > + regulator-max-microvolt = <1304000>; > + }; > + > + vreg_l18a_2p7: l18 { > + regulator-min-microvolt = <2704000>; > + regulator-max-microvolt = <2704000>; > + }; > + > + vreg_l19a_3p0: l19 { > + regulator-min-microvolt = <3008000>; > + regulator-max-microvolt = <3008000>; > + }; > + > + vreg_l20a_2p95: l20 { > + regulator-min-microvolt = <2960000>; > + regulator-max-microvolt = <2960000>; > + regulator-allow-set-load; > + }; > + > + vreg_l21a_2p95: l21 { > + regulator-min-microvolt = <2960000>; > + regulator-max-microvolt = <2960000>; > + regulator-system-load = <800000>; > + regulator-allow-set-load; > + }; > + > + vreg_l22a_2p85: l22 { > + regulator-min-microvolt = <2864000>; > + regulator-max-microvolt = <2864000>; > + }; > + > + vreg_l23a_3p3: l23 { > + regulator-min-microvolt = <3312000>; > + regulator-max-microvolt = <3312000>; > + }; > + > + vreg_l24a_3p075: l24 { > + regulator-min-microvolt = <3088000>; > + regulator-max-microvolt = <3088000>; > + }; > + > + vreg_l25a_3p3: l25 { > + regulator-min-microvolt = <3104000>; > + regulator-max-microvolt = <3312000>; > + }; > + > + vreg_l26a_1p2: l26 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-allow-set-load; > + }; > + > + vreg_l28_3p0: l28 { > + regulator-min-microvolt = <3008000>; > + regulator-max-microvolt = <3008000>; > + }; > + > + vreg_lvs1a_1p8: lvs1 { }; > + > + vreg_lvs2a_1p8: lvs2 { }; > + }; > + > + regulators-1 { > + compatible = "qcom,rpm-pmi8998-regulators"; > + > + vdd_bob-supply = <&vph_pwr>; > + > + vreg_bob: bob { > + regulator-min-microvolt = <3312000>; > + regulator-max-microvolt = <3600000>; > + }; > + }; > +}; > + > +&tlmm { > + gpio-reserved-ranges = <0 4>, <81 4>; > + > + cci1_default_state: cci1-default-state { > + pins = "gpio19", "gpio20"; > + function = "cci_i2c"; > + bias-disable; > + drive-strength = <2>; > + }; > + > + cdc_reset_n_state: cdc-reset-n-state { > + pins = "gpio64"; > + function = "gpio"; > + bias-pull-down; > + drive-strength = <16>; > + output-high; > + }; > + > + hall_sensor_default_state: hall-sensor-default-state { > + pins = "gpio124"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + input-enable; > + }; > + > + mdss_dsi_active_state: mdss-dsi-active-state { > + pins = "gpio94"; > + function = "gpio"; > + drive-strength = <8>; > + bias-disable; > + }; > + > + mdss_dsi_suspend_state: mdss-dsi-suspend-state { > + pins = "gpio94"; > + function = "gpio"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > + mdss_te_active_state: mdss-te-active-state { > + pins = "gpio10"; > + function = "mdp_vsync_a"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > + mdss_te_suspend_state: mdss-te-suspend-state { > + pins = "gpio10"; > + function = "mdp_vsync_a"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > + msm_mclk0_active_state: msm-mclk0-active-state { > + pins = "gpio13"; > + function = "cam_mclk"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + msm_mclk0_suspend_state: msm-mclk0-suspend-state { > + pins = "gpio13"; > + function = "cam_mclk"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > + msm_mclk1_active_state: msm-mclk1-active-state { > + pins = "gpio14"; > + function = "cam_mclk"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + msm_mclk1_suspend_state: msm-mclk1-suspend-state { > + pins = "gpio14"; > + function = "cam_mclk"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > + nfc_int_active_state: nfc-int-active-state { > + pins = "gpio92"; > + function = "gpio"; > + drive-strength = <6>; > + bias-pull-up; > + }; > + > + nfc_int_suspend_state: nfc-int-suspend-state { > + pins = "gpio92"; > + function = "gpio"; > + drive-strength = <6>; > + bias-pull-up; > + }; > + > + nfc_enable_active_state: nfc-enable-active-state { > + pins = "gpio12", "gpio116"; > + function = "gpio"; > + drive-strength = <6>; > + bias-pull-up; > + }; > + > + nfc_enable_suspend_state: nfc-enable-suspend-state { > + pins = "gpio12", "gpio116"; > + function = "gpio"; > + drive-strength = <6>; > + bias-disable; > + }; > + > + ts_active_state: ts-active-state { > + pins = "gpio89", "gpio125"; > + function = "gpio"; > + drive-strength = <16>; > + bias-pull-up; > + input-enable; > + }; > + > + ts_int_suspend_state: ts-int-suspend-state { > + pins = "gpio125"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + ts_reset_suspend_state: ts-reset-suspend-state { > + pins = "gpio89"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + wcd_int_n_state: wcd-int-n-state { > + pins = "gpio54"; > + function = "gpio"; > + bias-pull-down; > + drive-strength = <2>; > + input-enable; > + }; > + > + wsa_leftspk_pwr_n_state: wsa-leftspk-pwr-n-state { > + pins = "gpio65"; > + function = "gpio"; > + bias-disable; > + drive-strength = <2>; > + output-low; > + }; > + > + wsa_rightspk_pwr_n_state: wsa-rightspk-pwr-n-state { > + pins = "gpio66"; > + function = "gpio"; > + bias-disable; > + drive-strength = <2>; > + output-low; > + }; > +}; > + > +&pm8998_resin { > + linux,code = <KEY_VOLUMEDOWN>; > +}; > + > +&ufshc { > + vcc-supply = <&vreg_l20a_2p95>; > + vccq-supply = <&vreg_l26a_1p2>; > + vccq2-supply = <&vreg_s4a_1p8>; > + vcc-max-microamp = <750000>; > + vccq-max-microamp = <560000>; > + vccq2-max-microamp = <750000>; > + status = "okay"; > +}; > + > +&ufsphy { > + vdda-phy-supply = <&vreg_l1a_0p875>; > + vdda-pll-supply = <&vreg_l2a_1p2>; > + vddp-ref-clk-supply = <&vreg_l26a_1p2>; > + status = "okay"; > +}; > + > +&usb3 { > + /* Disable USB3 clock requirement as the device only supports USB2 */ > + qcom,select-utmi-as-pipe-clk; > + status = "okay"; > +}; > + > +&usb3_dwc3 { > + /* Drop the unused USB 3 PHY */ > + phys = <&qusb2phy>; > + phy-names = "usb2-phy"; > + > + /* Fastest mode for USB 2 */ > + maximum-speed = "high-speed"; > + > + /* Force to peripheral until we can switch modes */ > + dr_mode = "peripheral"; > +}; > + > +&wifi { > + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; > + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; > + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; > + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; > + status = "okay"; > +}; > diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi > index d09f2954b6f9..7929fa64e1ef 100644 > --- a/arch/arm64/boot/dts/qcom/pm8998.dtsi > +++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi > @@ -52,6 +52,14 @@ pm8998_pwrkey: pwrkey { > bias-pull-up; > linux,code = <KEY_POWER>; > }; > + > + pm8998_resin: resin { > + compatible = "qcom,pm8941-resin"; > + bias-pull-up; > + interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>; > + debounce = <15625>; > + status = "disabled"; > + }; > }; > > pm8998_temp: temp-alarm@2400 { > -- > 2.30.2 > ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2022-10-07 19:35 UTC | newest] Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2022-10-05 18:15 [PATCH v6 0/2] add device Xiaomi Mi 6 (codename sagit) and board binding Dzmitry Sankouski 2022-10-05 18:15 ` [PATCH v6 1/2] dt-bindings: arm: add xiaomi,sagit board based on msm8998 chip Dzmitry Sankouski 2022-10-06 7:03 ` Krzysztof Kozlowski 2022-10-05 18:15 ` [PATCH v6 2/2] arm64: dts: qcom: sagit: add initial device tree for sagit Dzmitry Sankouski 2022-10-05 18:30 ` Dzmitry Sankouski 2022-10-07 19:34 ` Konrad Dybcio 2022-10-05 19:13 ` Dzmitry Sankouski
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).