[PATCH V6 0/9] Add minimal boot support for IPQ5332

[PATCH V6 0/9] Add minimal boot support for IPQ5332

[Kathiravan T]

The IPQ5332 is Qualcomm's 802.11be SoC for Routers, Gateways and
Access Points.

This series adds minimal board boot support for ipq5332-mi01.2 board.

Changes in V6:
	- Added couple of patches 1/9 and 5/9 in the series to make sure
	  all the dependent patches are together
	- V5 can be found at
	  https://lore.kernel.org/linux-arm-msm/20230217075835.460-1-quic_kathirav@quicinc.com/

Changes in V5:
	- Dropped the clock-names from binding and DTS
	- Detailed change log is present in respective patches
	- V4 can be found at
	  https://lore.kernel.org/linux-arm-msm/20230208155232.11500-1-quic_kathirav@quicinc.com/

Changes in V4:
	- Dropped the pinctrl driver and its binding, since it is
	  already part of linux-next/master
	- Detailed change log is present in respective patches
	- V3 can be found at
	  https://lore.kernel.org/linux-arm-msm/20230206071217.29313-1-quic_kathirav@quicinc.com/

Changes in V3:
	- Detailed change log is present in respective patches
	- V2 can be found at
	  https://lore.kernel.org/linux-arm-msm/20230130114702.20606-1-quic_kathirav@quicinc.com/

Changes in V2:
	- Rebased on linux-next/master
	- Dropped the 'dt-bindings: mmc: sdhci-msm: add IPQ5332 compatible',
	  since it is already part of linux-next/master
	- Added a new patch 'clk: qcom: ipq5332: mark GPLL4 as critical temporarily'
	- Detailed change log is present in respective patches
	- V1 can be found at
	  https://lore.kernel.org/linux-arm-msm/20230125104520.89684-1-quic_kathirav@quicinc.com/

Kathiravan T (8):
  clk: qcom: Add STROMER PLUS PLL type for IPQ5332
  dt-bindings: clock: Add Qualcomm IPQ5332 GCC
  clk: qcom: add Global Clock controller (GCC) driver for IPQ5332 SoC
  clk: qcom: ipq5332: mark GPLL4 as ignore unused temporarily
  dt-bindings: qcom: add ipq5332 boards
  dt-bindings: firmware: qcom,scm: document IPQ5332 SCM
  arm64: dts: qcom: add IPQ5332 SoC and MI01.2 board support
  arm64: defconfig: Enable IPQ5332 SoC base configs

Varadarajan Narayanan (1):
  clk: qcom: clk-alpha-pll: Add support for Stromer PLLs

 .../devicetree/bindings/arm/qcom.yaml         |    7 +
 .../bindings/clock/qcom,ipq5332-gcc.yaml      |   53 +
 .../bindings/firmware/qcom,scm.yaml           |    1 +
 arch/arm64/boot/dts/qcom/Makefile             |    1 +
 arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts   |   75 +
 arch/arm64/boot/dts/qcom/ipq5332.dtsi         |  263 ++
 arch/arm64/configs/defconfig                  |    2 +
 drivers/clk/qcom/Kconfig                      |    8 +
 drivers/clk/qcom/Makefile                     |    1 +
 drivers/clk/qcom/clk-alpha-pll.c              |  139 +-
 drivers/clk/qcom/clk-alpha-pll.h              |   14 +-
 drivers/clk/qcom/gcc-ipq5332.c                | 3824 +++++++++++++++++
 include/dt-bindings/clock/qcom,ipq5332-gcc.h  |  356 ++
 13 files changed, 4742 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/qcom,ipq5332-gcc.yaml
 create mode 100644 arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
 create mode 100644 arch/arm64/boot/dts/qcom/ipq5332.dtsi
 create mode 100644 drivers/clk/qcom/gcc-ipq5332.c
 create mode 100644 include/dt-bindings/clock/qcom,ipq5332-gcc.h


base-commit: dc837c1a5137a8cf2e9432c1891392b6a66f4d8d
-- 
2.17.1

[PATCH V6 1/9] clk: qcom: clk-alpha-pll: Add support for Stromer PLLs

[Kathiravan T]

From: Varadarajan Narayanan <quic_varada@quicinc.com>

Add programming sequence support for managing the Stromer
PLLs.

Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Co-developed-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
---
Changes in V6:
	- This patch newly added in V6
	- Pick up R-b tag

 drivers/clk/qcom/clk-alpha-pll.c | 128 ++++++++++++++++++++++++++++++-
 drivers/clk/qcom/clk-alpha-pll.h |  13 +++-
 2 files changed, 139 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index e266379427f2..14f9436b62fc 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
  * Copyright (c) 2015, 2018, The Linux Foundation. All rights reserved.
- * Copyright (c) 2021, Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2021, 2023, Qualcomm Innovation Center, Inc. All rights reserved.
  */
 
 #include <linux/kernel.h>
@@ -204,6 +204,18 @@ const u8 clk_alpha_pll_regs[][PLL_OFF_MAX_REGS] = {
 		[PLL_OFF_CONFIG_CTL] = 0x1C,
 		[PLL_OFF_STATUS] = 0x20,
 	},
+	[CLK_ALPHA_PLL_TYPE_STROMER] = {
+		[PLL_OFF_L_VAL] = 0x08,
+		[PLL_OFF_ALPHA_VAL] = 0x10,
+		[PLL_OFF_ALPHA_VAL_U] = 0x14,
+		[PLL_OFF_USER_CTL] = 0x18,
+		[PLL_OFF_USER_CTL_U] = 0x1c,
+		[PLL_OFF_CONFIG_CTL] = 0x20,
+		[PLL_OFF_CONFIG_CTL_U] = 0xff,
+		[PLL_OFF_TEST_CTL] = 0x30,
+		[PLL_OFF_TEST_CTL_U] = 0x34,
+		[PLL_OFF_STATUS] = 0x28,
+	},
 };
 EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);
 
@@ -215,6 +227,8 @@ EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);
 #define ALPHA_BITWIDTH		32U
 #define ALPHA_SHIFT(w)		min(w, ALPHA_BITWIDTH)
 
+#define	ALPHA_PLL_STATUS_REG_SHIFT	8
+
 #define PLL_HUAYRA_M_WIDTH		8
 #define PLL_HUAYRA_M_SHIFT		8
 #define PLL_HUAYRA_M_MASK		0xff
@@ -2329,3 +2343,115 @@ const struct clk_ops clk_alpha_pll_rivian_evo_ops = {
 	.round_rate = clk_rivian_evo_pll_round_rate,
 };
 EXPORT_SYMBOL_GPL(clk_alpha_pll_rivian_evo_ops);
+
+void clk_stromer_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
+			       const struct alpha_pll_config *config)
+{
+	u32 val, val_u, mask, mask_u;
+
+	regmap_write(regmap, PLL_L_VAL(pll), config->l);
+	regmap_write(regmap, PLL_ALPHA_VAL(pll), config->alpha);
+	regmap_write(regmap, PLL_CONFIG_CTL(pll), config->config_ctl_val);
+
+	if (pll_has_64bit_config(pll))
+		regmap_write(regmap, PLL_CONFIG_CTL_U(pll),
+			     config->config_ctl_hi_val);
+
+	if (pll_alpha_width(pll) > 32)
+		regmap_write(regmap, PLL_ALPHA_VAL_U(pll), config->alpha_hi);
+
+	val = config->main_output_mask;
+	val |= config->aux_output_mask;
+	val |= config->aux2_output_mask;
+	val |= config->early_output_mask;
+	val |= config->pre_div_val;
+	val |= config->post_div_val;
+	val |= config->vco_val;
+	val |= config->alpha_en_mask;
+	val |= config->alpha_mode_mask;
+
+	mask = config->main_output_mask;
+	mask |= config->aux_output_mask;
+	mask |= config->aux2_output_mask;
+	mask |= config->early_output_mask;
+	mask |= config->pre_div_mask;
+	mask |= config->post_div_mask;
+	mask |= config->vco_mask;
+	mask |= config->alpha_en_mask;
+	mask |= config->alpha_mode_mask;
+
+	regmap_update_bits(regmap, PLL_USER_CTL(pll), mask, val);
+
+	/* Stromer APSS PLL does not enable LOCK_DET by default, so enable it */
+	val_u = config->status_val << ALPHA_PLL_STATUS_REG_SHIFT;
+	val_u |= config->lock_det;
+
+	mask_u = config->status_mask;
+	mask_u |= config->lock_det;
+
+	regmap_update_bits(regmap, PLL_USER_CTL_U(pll), mask_u, val_u);
+	regmap_write(regmap, PLL_TEST_CTL(pll), config->test_ctl_val);
+	regmap_write(regmap, PLL_TEST_CTL_U(pll), config->test_ctl_hi_val);
+
+	if (pll->flags & SUPPORTS_FSM_MODE)
+		qcom_pll_set_fsm_mode(regmap, PLL_MODE(pll), 6, 0);
+}
+EXPORT_SYMBOL_GPL(clk_stromer_pll_configure);
+
+static int clk_alpha_pll_stromer_determine_rate(struct clk_hw *hw,
+						struct clk_rate_request *req)
+{
+	u32 l;
+	u64 a;
+
+	req->rate = alpha_pll_round_rate(req->rate, req->best_parent_rate,
+					 &l, &a, ALPHA_REG_BITWIDTH);
+
+	return 0;
+}
+
+static int clk_alpha_pll_stromer_set_rate(struct clk_hw *hw, unsigned long rate,
+					  unsigned long prate)
+{
+	struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
+	int ret;
+	u32 l;
+	u64 a;
+
+	rate = alpha_pll_round_rate(rate, prate, &l, &a, ALPHA_REG_BITWIDTH);
+
+	regmap_write(pll->clkr.regmap, PLL_L_VAL(pll), l);
+	regmap_write(pll->clkr.regmap, PLL_ALPHA_VAL(pll), a);
+	regmap_write(pll->clkr.regmap, PLL_ALPHA_VAL_U(pll),
+		     a >> ALPHA_BITWIDTH);
+
+	regmap_update_bits(pll->clkr.regmap, PLL_USER_CTL(pll),
+			   PLL_ALPHA_EN, PLL_ALPHA_EN);
+
+	if (!clk_hw_is_enabled(hw))
+		return 0;
+
+	/*
+	 * Stromer PLL supports Dynamic programming.
+	 * It allows the PLL frequency to be changed on-the-fly without first
+	 * execution of a shutdown procedure followed by a bring up procedure.
+	 */
+	regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll), PLL_UPDATE,
+			   PLL_UPDATE);
+
+	ret = wait_for_pll_update(pll);
+	if (ret)
+		return ret;
+
+	return wait_for_pll_enable_lock(pll);
+}
+
+const struct clk_ops clk_alpha_pll_stromer_ops = {
+	.enable = clk_alpha_pll_enable,
+	.disable = clk_alpha_pll_disable,
+	.is_enabled = clk_alpha_pll_is_enabled,
+	.recalc_rate = clk_alpha_pll_recalc_rate,
+	.determine_rate = clk_alpha_pll_stromer_determine_rate,
+	.set_rate = clk_alpha_pll_stromer_set_rate,
+};
+EXPORT_SYMBOL_GPL(clk_alpha_pll_stromer_ops);
diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
index c67cfda27ecb..ff25c7f7b43e 100644
--- a/drivers/clk/qcom/clk-alpha-pll.h
+++ b/drivers/clk/qcom/clk-alpha-pll.h
@@ -1,5 +1,9 @@
 /* SPDX-License-Identifier: GPL-2.0 */
-/* Copyright (c) 2015, 2018, The Linux Foundation. All rights reserved. */
+/*
+ * Copyright (c) 2015, 2018, 2021 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
 
 #ifndef __QCOM_CLK_ALPHA_PLL_H__
 #define __QCOM_CLK_ALPHA_PLL_H__
@@ -22,6 +26,7 @@ enum {
 	CLK_ALPHA_PLL_TYPE_RIVIAN_EVO,
 	CLK_ALPHA_PLL_TYPE_DEFAULT_EVO,
 	CLK_ALPHA_PLL_TYPE_BRAMMO_EVO,
+	CLK_ALPHA_PLL_TYPE_STROMER,
 	CLK_ALPHA_PLL_TYPE_MAX,
 };
 
@@ -131,6 +136,9 @@ struct alpha_pll_config {
 	u32 post_div_mask;
 	u32 vco_val;
 	u32 vco_mask;
+	u32 status_val;
+	u32 status_mask;
+	u32 lock_det;
 };
 
 extern const struct clk_ops clk_alpha_pll_ops;
@@ -139,6 +147,7 @@ extern const struct clk_ops clk_alpha_pll_hwfsm_ops;
 extern const struct clk_ops clk_alpha_pll_postdiv_ops;
 extern const struct clk_ops clk_alpha_pll_huayra_ops;
 extern const struct clk_ops clk_alpha_pll_postdiv_ro_ops;
+extern const struct clk_ops clk_alpha_pll_stromer_ops;
 
 extern const struct clk_ops clk_alpha_pll_fabia_ops;
 extern const struct clk_ops clk_alpha_pll_fixed_fabia_ops;
@@ -188,5 +197,7 @@ void clk_lucid_evo_pll_configure(struct clk_alpha_pll *pll, struct regmap *regma
 				 const struct alpha_pll_config *config);
 void clk_rivian_evo_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
 				  const struct alpha_pll_config *config);
+void clk_stromer_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
+			       const struct alpha_pll_config *config);
 
 #endif
-- 
2.17.1

[PATCH V6 2/9] clk: qcom: Add STROMER PLUS PLL type for IPQ5332

[Kathiravan T]

Add the support for stromer plus pll, which is found on the IPQ5332
SoCs. Programming sequence is same as the stromer pll, so we can re-use
the same.

Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
---
Changes in V6:
	- No changes

Changes in V5:
	- No changes

Changes in V4:
	- No changes

Changes in V3:
	- No changes

Changes in V2:
	- Added the Reviewed-by tag

 drivers/clk/qcom/clk-alpha-pll.c | 11 +++++++++++
 drivers/clk/qcom/clk-alpha-pll.h |  1 +
 2 files changed, 12 insertions(+)

diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index 14f9436b62fc..b9f6535a7ba7 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -216,6 +216,17 @@ const u8 clk_alpha_pll_regs[][PLL_OFF_MAX_REGS] = {
 		[PLL_OFF_TEST_CTL_U] = 0x34,
 		[PLL_OFF_STATUS] = 0x28,
 	},
+	[CLK_ALPHA_PLL_TYPE_STROMER_PLUS] =  {
+		[PLL_OFF_L_VAL] = 0x04,
+		[PLL_OFF_USER_CTL] = 0x08,
+		[PLL_OFF_USER_CTL_U] = 0x0c,
+		[PLL_OFF_CONFIG_CTL] = 0x10,
+		[PLL_OFF_TEST_CTL] = 0x14,
+		[PLL_OFF_TEST_CTL_U] = 0x18,
+		[PLL_OFF_STATUS] = 0x1c,
+		[PLL_OFF_ALPHA_VAL] = 0x24,
+		[PLL_OFF_ALPHA_VAL_U] = 0x28,
+	},
 };
 EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);
 
diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
index ff25c7f7b43e..d07b17186b90 100644
--- a/drivers/clk/qcom/clk-alpha-pll.h
+++ b/drivers/clk/qcom/clk-alpha-pll.h
@@ -27,6 +27,7 @@ enum {
 	CLK_ALPHA_PLL_TYPE_DEFAULT_EVO,
 	CLK_ALPHA_PLL_TYPE_BRAMMO_EVO,
 	CLK_ALPHA_PLL_TYPE_STROMER,
+	CLK_ALPHA_PLL_TYPE_STROMER_PLUS,
 	CLK_ALPHA_PLL_TYPE_MAX,
 };
 
-- 
2.17.1

[PATCH V6 3/9] dt-bindings: clock: Add Qualcomm IPQ5332 GCC

[Kathiravan T]

Add binding for the Qualcomm IPQ5332 Global Clock Controller.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
---
Changes in V6:
	- No changes

Changes in V5:
	- Dropped the clock-names, as suggested by Bjorn in IPQ9574
	  series
	- Made Bjorn as Maintainer

Changes in V4:
	- Pick up the R-b tag

Changes in V3:
	- Actually I missed to remove the clocks in V2 which are
	  supposed to
	  be removed. In V3 I have removed those and they are
	  GCC_APSS_AHB_CLK, GCC_APSS_AHB_CLK_SRC, GCC_APSS_AXI_CLK
	- For the same, didn't add the Reviewed-By tags from Stephen and
	  Krzysztof

Changes in V2:
	- property 'clocks' is marked required
	- Renamed the include file name to match with compatible

 .../bindings/clock/qcom,ipq5332-gcc.yaml      |  53 +++
 include/dt-bindings/clock/qcom,ipq5332-gcc.h  | 356 ++++++++++++++++++
 2 files changed, 409 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/qcom,ipq5332-gcc.yaml
 create mode 100644 include/dt-bindings/clock/qcom,ipq5332-gcc.h

diff --git a/Documentation/devicetree/bindings/clock/qcom,ipq5332-gcc.yaml b/Documentation/devicetree/bindings/clock/qcom,ipq5332-gcc.yaml
new file mode 100644
index 000000000000..718fe0625424
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/qcom,ipq5332-gcc.yaml
@@ -0,0 +1,53 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/qcom,ipq5332-gcc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Global Clock & Reset Controller on IPQ5332
+
+maintainers:
+  - Bjorn Andersson <andersson@kernel.org>
+
+description: |
+  Qualcomm global clock control module provides the clocks, resets and power
+  domains on IPQ5332.
+
+  See also:: include/dt-bindings/clock/qcom,gcc-ipq5332.h
+
+allOf:
+  - $ref: qcom,gcc.yaml#
+
+properties:
+  compatible:
+    const: qcom,ipq5332-gcc
+
+  clocks:
+    items:
+      - description: Board XO clock source
+      - description: Sleep clock source
+      - description: PCIE 2lane PHY pipe clock source
+      - description: PCIE 2lane x1 PHY pipe clock source (For second lane)
+      - description: USB PCIE wrapper pipe clock source
+
+required:
+  - compatible
+  - clocks
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    clock-controller@1800000 {
+      compatible = "qcom,ipq5332-gcc";
+      reg = <0x01800000 0x80000>;
+      clocks = <&xo_board>,
+               <&sleep_clk>,
+               <&pcie_2lane_phy_pipe_clk>,
+               <&pcie_2lane_phy_pipe_clk_x1>,
+               <&usb_pcie_wrapper_pipe_clk>;
+      #clock-cells = <1>;
+      #power-domain-cells = <1>;
+      #reset-cells = <1>;
+    };
+...
diff --git a/include/dt-bindings/clock/qcom,ipq5332-gcc.h b/include/dt-bindings/clock/qcom,ipq5332-gcc.h
new file mode 100644
index 000000000000..8a405a0a96d0
--- /dev/null
+++ b/include/dt-bindings/clock/qcom,ipq5332-gcc.h
@@ -0,0 +1,356 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#ifndef _DT_BINDINGS_CLK_QCOM_GCC_IPQ5332_H
+#define _DT_BINDINGS_CLK_QCOM_GCC_IPQ5332_H
+
+#define GPLL0_MAIN					0
+#define GPLL0						1
+#define GPLL2_MAIN					2
+#define GPLL2						3
+#define GPLL4_MAIN					4
+#define GPLL4						5
+#define GCC_ADSS_PWM_CLK				6
+#define GCC_ADSS_PWM_CLK_SRC				7
+#define GCC_AHB_CLK					8
+#define GCC_APSS_AXI_CLK_SRC				9
+#define GCC_BLSP1_AHB_CLK				10
+#define GCC_BLSP1_QUP1_I2C_APPS_CLK			11
+#define GCC_BLSP1_QUP1_SPI_APPS_CLK			12
+#define GCC_BLSP1_QUP1_SPI_APPS_CLK_SRC			13
+#define GCC_BLSP1_QUP2_I2C_APPS_CLK			14
+#define GCC_BLSP1_QUP2_SPI_APPS_CLK			15
+#define GCC_BLSP1_QUP2_SPI_APPS_CLK_SRC			16
+#define GCC_BLSP1_QUP3_I2C_APPS_CLK			17
+#define GCC_BLSP1_QUP3_SPI_APPS_CLK			18
+#define GCC_BLSP1_QUP3_SPI_APPS_CLK_SRC			19
+#define GCC_BLSP1_SLEEP_CLK				20
+#define GCC_BLSP1_UART1_APPS_CLK			21
+#define GCC_BLSP1_UART1_APPS_CLK_SRC			22
+#define GCC_BLSP1_UART2_APPS_CLK			23
+#define GCC_BLSP1_UART2_APPS_CLK_SRC			24
+#define GCC_BLSP1_UART3_APPS_CLK			25
+#define GCC_BLSP1_UART3_APPS_CLK_SRC			26
+#define GCC_CE_AHB_CLK					27
+#define GCC_CE_AXI_CLK					28
+#define GCC_CE_PCNOC_AHB_CLK				29
+#define GCC_CMN_12GPLL_AHB_CLK				30
+#define GCC_CMN_12GPLL_APU_CLK				31
+#define GCC_CMN_12GPLL_SYS_CLK				32
+#define GCC_GP1_CLK					33
+#define GCC_GP1_CLK_SRC					34
+#define GCC_GP2_CLK					35
+#define GCC_GP2_CLK_SRC					36
+#define GCC_LPASS_CORE_AXIM_CLK				37
+#define GCC_LPASS_SWAY_CLK				38
+#define GCC_LPASS_SWAY_CLK_SRC				39
+#define GCC_MDIO_AHB_CLK				40
+#define GCC_MDIO_SLAVE_AHB_CLK				41
+#define GCC_MEM_NOC_Q6_AXI_CLK				42
+#define GCC_MEM_NOC_TS_CLK				43
+#define GCC_NSS_TS_CLK					44
+#define GCC_NSS_TS_CLK_SRC				45
+#define GCC_NSSCC_CLK					46
+#define GCC_NSSCFG_CLK					47
+#define GCC_NSSNOC_ATB_CLK				48
+#define GCC_NSSNOC_NSSCC_CLK				49
+#define GCC_NSSNOC_QOSGEN_REF_CLK			50
+#define GCC_NSSNOC_SNOC_1_CLK				51
+#define GCC_NSSNOC_SNOC_CLK				52
+#define GCC_NSSNOC_TIMEOUT_REF_CLK			53
+#define GCC_NSSNOC_XO_DCD_CLK				54
+#define GCC_PCIE3X1_0_AHB_CLK				55
+#define GCC_PCIE3X1_0_AUX_CLK				56
+#define GCC_PCIE3X1_0_AXI_CLK_SRC			57
+#define GCC_PCIE3X1_0_AXI_M_CLK				58
+#define GCC_PCIE3X1_0_AXI_S_BRIDGE_CLK			59
+#define GCC_PCIE3X1_0_AXI_S_CLK				60
+#define GCC_PCIE3X1_0_PIPE_CLK				61
+#define GCC_PCIE3X1_0_RCHG_CLK				62
+#define GCC_PCIE3X1_0_RCHG_CLK_SRC			63
+#define GCC_PCIE3X1_1_AHB_CLK				64
+#define GCC_PCIE3X1_1_AUX_CLK				65
+#define GCC_PCIE3X1_1_AXI_CLK_SRC			66
+#define GCC_PCIE3X1_1_AXI_M_CLK				67
+#define GCC_PCIE3X1_1_AXI_S_BRIDGE_CLK			68
+#define GCC_PCIE3X1_1_AXI_S_CLK				69
+#define GCC_PCIE3X1_1_PIPE_CLK				70
+#define GCC_PCIE3X1_1_RCHG_CLK				71
+#define GCC_PCIE3X1_1_RCHG_CLK_SRC			72
+#define GCC_PCIE3X1_PHY_AHB_CLK				73
+#define GCC_PCIE3X2_AHB_CLK				74
+#define GCC_PCIE3X2_AUX_CLK				75
+#define GCC_PCIE3X2_AXI_M_CLK				76
+#define GCC_PCIE3X2_AXI_M_CLK_SRC			77
+#define GCC_PCIE3X2_AXI_S_BRIDGE_CLK			78
+#define GCC_PCIE3X2_AXI_S_CLK				79
+#define GCC_PCIE3X2_AXI_S_CLK_SRC			80
+#define GCC_PCIE3X2_PHY_AHB_CLK				81
+#define GCC_PCIE3X2_PIPE_CLK				82
+#define GCC_PCIE3X2_RCHG_CLK				83
+#define GCC_PCIE3X2_RCHG_CLK_SRC			84
+#define GCC_PCIE_AUX_CLK_SRC				85
+#define GCC_PCNOC_AT_CLK				86
+#define GCC_PCNOC_BFDCD_CLK_SRC				87
+#define GCC_PCNOC_LPASS_CLK				88
+#define GCC_PRNG_AHB_CLK				89
+#define GCC_Q6_AHB_CLK					90
+#define GCC_Q6_AHB_S_CLK				91
+#define GCC_Q6_AXIM_CLK					92
+#define GCC_Q6_AXIM_CLK_SRC				93
+#define GCC_Q6_AXIS_CLK					94
+#define GCC_Q6_TSCTR_1TO2_CLK				95
+#define GCC_Q6SS_ATBM_CLK				96
+#define GCC_Q6SS_PCLKDBG_CLK				97
+#define GCC_Q6SS_TRIG_CLK				98
+#define GCC_QDSS_AT_CLK					99
+#define GCC_QDSS_AT_CLK_SRC				100
+#define GCC_QDSS_CFG_AHB_CLK				101
+#define GCC_QDSS_DAP_AHB_CLK				102
+#define GCC_QDSS_DAP_CLK				103
+#define GCC_QDSS_DAP_DIV_CLK_SRC			104
+#define GCC_QDSS_ETR_USB_CLK				105
+#define GCC_QDSS_EUD_AT_CLK				106
+#define GCC_QDSS_TSCTR_CLK_SRC				107
+#define GCC_QPIC_AHB_CLK				108
+#define GCC_QPIC_CLK					109
+#define GCC_QPIC_IO_MACRO_CLK				110
+#define GCC_QPIC_IO_MACRO_CLK_SRC			111
+#define GCC_QPIC_SLEEP_CLK				112
+#define GCC_SDCC1_AHB_CLK				113
+#define GCC_SDCC1_APPS_CLK				114
+#define GCC_SDCC1_APPS_CLK_SRC				115
+#define GCC_SLEEP_CLK_SRC				116
+#define GCC_SNOC_LPASS_CFG_CLK				117
+#define GCC_SNOC_NSSNOC_1_CLK				118
+#define GCC_SNOC_NSSNOC_CLK				119
+#define GCC_SNOC_PCIE3_1LANE_1_M_CLK			120
+#define GCC_SNOC_PCIE3_1LANE_1_S_CLK			121
+#define GCC_SNOC_PCIE3_1LANE_M_CLK			122
+#define GCC_SNOC_PCIE3_1LANE_S_CLK			123
+#define GCC_SNOC_PCIE3_2LANE_M_CLK			124
+#define GCC_SNOC_PCIE3_2LANE_S_CLK			125
+#define GCC_SNOC_USB_CLK				126
+#define GCC_SYS_NOC_AT_CLK				127
+#define GCC_SYS_NOC_WCSS_AHB_CLK			128
+#define GCC_SYSTEM_NOC_BFDCD_CLK_SRC			129
+#define GCC_UNIPHY0_AHB_CLK				130
+#define GCC_UNIPHY0_SYS_CLK				131
+#define GCC_UNIPHY1_AHB_CLK				132
+#define GCC_UNIPHY1_SYS_CLK				133
+#define GCC_UNIPHY_SYS_CLK_SRC				134
+#define GCC_USB0_AUX_CLK				135
+#define GCC_USB0_AUX_CLK_SRC				136
+#define GCC_USB0_EUD_AT_CLK				137
+#define GCC_USB0_LFPS_CLK				138
+#define GCC_USB0_LFPS_CLK_SRC				139
+#define GCC_USB0_MASTER_CLK				140
+#define GCC_USB0_MASTER_CLK_SRC				141
+#define GCC_USB0_MOCK_UTMI_CLK				142
+#define GCC_USB0_MOCK_UTMI_CLK_SRC			143
+#define GCC_USB0_MOCK_UTMI_DIV_CLK_SRC			144
+#define GCC_USB0_PHY_CFG_AHB_CLK			145
+#define GCC_USB0_PIPE_CLK				146
+#define GCC_USB0_SLEEP_CLK				147
+#define GCC_WCSS_AHB_CLK_SRC				148
+#define GCC_WCSS_AXIM_CLK				149
+#define GCC_WCSS_AXIS_CLK				150
+#define GCC_WCSS_DBG_IFC_APB_BDG_CLK			151
+#define GCC_WCSS_DBG_IFC_APB_CLK			152
+#define GCC_WCSS_DBG_IFC_ATB_BDG_CLK			153
+#define GCC_WCSS_DBG_IFC_ATB_CLK			154
+#define GCC_WCSS_DBG_IFC_NTS_BDG_CLK			155
+#define GCC_WCSS_DBG_IFC_NTS_CLK			156
+#define GCC_WCSS_ECAHB_CLK				157
+#define GCC_WCSS_MST_ASYNC_BDG_CLK			158
+#define GCC_WCSS_SLV_ASYNC_BDG_CLK			159
+#define GCC_XO_CLK					160
+#define GCC_XO_CLK_SRC					161
+#define GCC_XO_DIV4_CLK					162
+#define GCC_IM_SLEEP_CLK				163
+#define GCC_NSSNOC_PCNOC_1_CLK				164
+#define GCC_MEM_NOC_AHB_CLK				165
+#define GCC_MEM_NOC_APSS_AXI_CLK			166
+#define GCC_SNOC_QOSGEN_EXTREF_DIV_CLK_SRC		167
+#define GCC_MEM_NOC_QOSGEN_EXTREF_CLK			168
+#define GCC_PCIE3X2_PIPE_CLK_SRC			169
+#define GCC_PCIE3X1_0_PIPE_CLK_SRC			170
+#define GCC_PCIE3X1_1_PIPE_CLK_SRC			171
+#define GCC_USB0_PIPE_CLK_SRC				172
+
+#define GCC_ADSS_BCR					0
+#define GCC_ADSS_PWM_CLK_ARES				1
+#define GCC_AHB_CLK_ARES				2
+#define GCC_APC0_VOLTAGE_DROOP_DETECTOR_BCR		3
+#define GCC_APC0_VOLTAGE_DROOP_DETECTOR_GPLL0_CLK_ARES	4
+#define GCC_APSS_AHB_CLK_ARES				5
+#define GCC_APSS_AXI_CLK_ARES				6
+#define GCC_BLSP1_AHB_CLK_ARES				7
+#define GCC_BLSP1_BCR					8
+#define GCC_BLSP1_QUP1_BCR				9
+#define GCC_BLSP1_QUP1_I2C_APPS_CLK_ARES		10
+#define GCC_BLSP1_QUP1_SPI_APPS_CLK_ARES		11
+#define GCC_BLSP1_QUP2_BCR				12
+#define GCC_BLSP1_QUP2_I2C_APPS_CLK_ARES		13
+#define GCC_BLSP1_QUP2_SPI_APPS_CLK_ARES		14
+#define GCC_BLSP1_QUP3_BCR				15
+#define GCC_BLSP1_QUP3_I2C_APPS_CLK_ARES		16
+#define GCC_BLSP1_QUP3_SPI_APPS_CLK_ARES		17
+#define GCC_BLSP1_SLEEP_CLK_ARES			18
+#define GCC_BLSP1_UART1_APPS_CLK_ARES			19
+#define GCC_BLSP1_UART1_BCR				20
+#define GCC_BLSP1_UART2_APPS_CLK_ARES			21
+#define GCC_BLSP1_UART2_BCR				22
+#define GCC_BLSP1_UART3_APPS_CLK_ARES			23
+#define GCC_BLSP1_UART3_BCR				24
+#define GCC_CE_BCR					25
+#define GCC_CMN_BLK_BCR					26
+#define GCC_CMN_LDO0_BCR				27
+#define GCC_CMN_LDO1_BCR				28
+#define GCC_DCC_BCR					29
+#define GCC_GP1_CLK_ARES				30
+#define GCC_GP2_CLK_ARES				31
+#define GCC_LPASS_BCR					32
+#define GCC_LPASS_CORE_AXIM_CLK_ARES			33
+#define GCC_LPASS_SWAY_CLK_ARES				34
+#define GCC_MDIOM_BCR					35
+#define GCC_MDIOS_BCR					36
+#define GCC_NSS_BCR					37
+#define GCC_NSS_TS_CLK_ARES				38
+#define GCC_NSSCC_CLK_ARES				39
+#define GCC_NSSCFG_CLK_ARES				40
+#define GCC_NSSNOC_ATB_CLK_ARES				41
+#define GCC_NSSNOC_NSSCC_CLK_ARES			42
+#define GCC_NSSNOC_QOSGEN_REF_CLK_ARES			43
+#define GCC_NSSNOC_SNOC_1_CLK_ARES			44
+#define GCC_NSSNOC_SNOC_CLK_ARES			45
+#define GCC_NSSNOC_TIMEOUT_REF_CLK_ARES			46
+#define GCC_NSSNOC_XO_DCD_CLK_ARES			47
+#define GCC_PCIE3X1_0_AHB_CLK_ARES			48
+#define GCC_PCIE3X1_0_AUX_CLK_ARES			49
+#define GCC_PCIE3X1_0_AXI_M_CLK_ARES			50
+#define GCC_PCIE3X1_0_AXI_S_BRIDGE_CLK_ARES		51
+#define GCC_PCIE3X1_0_AXI_S_CLK_ARES			52
+#define GCC_PCIE3X1_0_BCR				53
+#define GCC_PCIE3X1_0_LINK_DOWN_BCR			54
+#define GCC_PCIE3X1_0_PHY_BCR				55
+#define GCC_PCIE3X1_0_PHY_PHY_BCR			56
+#define GCC_PCIE3X1_1_AHB_CLK_ARES			57
+#define GCC_PCIE3X1_1_AUX_CLK_ARES			58
+#define GCC_PCIE3X1_1_AXI_M_CLK_ARES			59
+#define GCC_PCIE3X1_1_AXI_S_BRIDGE_CLK_ARES		60
+#define GCC_PCIE3X1_1_AXI_S_CLK_ARES			61
+#define GCC_PCIE3X1_1_BCR				62
+#define GCC_PCIE3X1_1_LINK_DOWN_BCR			63
+#define GCC_PCIE3X1_1_PHY_BCR				64
+#define GCC_PCIE3X1_1_PHY_PHY_BCR			65
+#define GCC_PCIE3X1_PHY_AHB_CLK_ARES			66
+#define GCC_PCIE3X2_AHB_CLK_ARES			67
+#define GCC_PCIE3X2_AUX_CLK_ARES			68
+#define GCC_PCIE3X2_AXI_M_CLK_ARES			69
+#define GCC_PCIE3X2_AXI_S_BRIDGE_CLK_ARES		70
+#define GCC_PCIE3X2_AXI_S_CLK_ARES			71
+#define GCC_PCIE3X2_BCR					72
+#define GCC_PCIE3X2_LINK_DOWN_BCR			73
+#define GCC_PCIE3X2_PHY_AHB_CLK_ARES			74
+#define GCC_PCIE3X2_PHY_BCR				75
+#define GCC_PCIE3X2PHY_PHY_BCR				76
+#define GCC_PCNOC_BCR					77
+#define GCC_PCNOC_LPASS_CLK_ARES			78
+#define GCC_PRNG_AHB_CLK_ARES				79
+#define GCC_PRNG_BCR					80
+#define GCC_Q6_AHB_CLK_ARES				81
+#define GCC_Q6_AHB_S_CLK_ARES				82
+#define GCC_Q6_AXIM_CLK_ARES				83
+#define GCC_Q6_AXIS_CLK_ARES				84
+#define GCC_Q6_TSCTR_1TO2_CLK_ARES			85
+#define GCC_Q6SS_ATBM_CLK_ARES				86
+#define GCC_Q6SS_PCLKDBG_CLK_ARES			87
+#define GCC_Q6SS_TRIG_CLK_ARES				88
+#define GCC_QDSS_APB2JTAG_CLK_ARES			89
+#define GCC_QDSS_AT_CLK_ARES				90
+#define GCC_QDSS_BCR					91
+#define GCC_QDSS_CFG_AHB_CLK_ARES			92
+#define GCC_QDSS_DAP_AHB_CLK_ARES			93
+#define GCC_QDSS_DAP_CLK_ARES				94
+#define GCC_QDSS_ETR_USB_CLK_ARES			95
+#define GCC_QDSS_EUD_AT_CLK_ARES			96
+#define GCC_QDSS_STM_CLK_ARES				97
+#define GCC_QDSS_TRACECLKIN_CLK_ARES			98
+#define GCC_QDSS_TS_CLK_ARES				99
+#define GCC_QDSS_TSCTR_DIV16_CLK_ARES			100
+#define GCC_QDSS_TSCTR_DIV2_CLK_ARES			101
+#define GCC_QDSS_TSCTR_DIV3_CLK_ARES			102
+#define GCC_QDSS_TSCTR_DIV4_CLK_ARES			103
+#define GCC_QDSS_TSCTR_DIV8_CLK_ARES			104
+#define GCC_QPIC_AHB_CLK_ARES				105
+#define GCC_QPIC_CLK_ARES				106
+#define GCC_QPIC_BCR					107
+#define GCC_QPIC_IO_MACRO_CLK_ARES			108
+#define GCC_QPIC_SLEEP_CLK_ARES				109
+#define GCC_QUSB2_0_PHY_BCR				110
+#define GCC_SDCC1_AHB_CLK_ARES				111
+#define GCC_SDCC1_APPS_CLK_ARES				112
+#define GCC_SDCC_BCR					113
+#define GCC_SNOC_BCR					114
+#define GCC_SNOC_LPASS_CFG_CLK_ARES			115
+#define GCC_SNOC_NSSNOC_1_CLK_ARES			116
+#define GCC_SNOC_NSSNOC_CLK_ARES			117
+#define GCC_SYS_NOC_QDSS_STM_AXI_CLK_ARES		118
+#define GCC_SYS_NOC_WCSS_AHB_CLK_ARES			119
+#define GCC_UNIPHY0_AHB_CLK_ARES			120
+#define GCC_UNIPHY0_BCR					121
+#define GCC_UNIPHY0_SYS_CLK_ARES			122
+#define GCC_UNIPHY1_AHB_CLK_ARES			123
+#define GCC_UNIPHY1_BCR					124
+#define GCC_UNIPHY1_SYS_CLK_ARES			125
+#define GCC_USB0_AUX_CLK_ARES				126
+#define GCC_USB0_EUD_AT_CLK_ARES			127
+#define GCC_USB0_LFPS_CLK_ARES				128
+#define GCC_USB0_MASTER_CLK_ARES			129
+#define GCC_USB0_MOCK_UTMI_CLK_ARES			130
+#define GCC_USB0_PHY_BCR				131
+#define GCC_USB0_PHY_CFG_AHB_CLK_ARES			132
+#define GCC_USB0_SLEEP_CLK_ARES				133
+#define GCC_USB3PHY_0_PHY_BCR				134
+#define GCC_USB_BCR					135
+#define GCC_WCSS_AXIM_CLK_ARES				136
+#define GCC_WCSS_AXIS_CLK_ARES				137
+#define GCC_WCSS_BCR					138
+#define GCC_WCSS_DBG_IFC_APB_BDG_CLK_ARES		139
+#define GCC_WCSS_DBG_IFC_APB_CLK_ARES			140
+#define GCC_WCSS_DBG_IFC_ATB_BDG_CLK_ARES		141
+#define GCC_WCSS_DBG_IFC_ATB_CLK_ARES			142
+#define GCC_WCSS_DBG_IFC_NTS_BDG_CLK_ARES		143
+#define GCC_WCSS_DBG_IFC_NTS_CLK_ARES			144
+#define GCC_WCSS_ECAHB_CLK_ARES				145
+#define GCC_WCSS_MST_ASYNC_BDG_CLK_ARES			146
+#define GCC_WCSS_Q6_BCR					147
+#define GCC_WCSS_SLV_ASYNC_BDG_CLK_ARES			148
+#define GCC_XO_CLK_ARES					149
+#define GCC_XO_DIV4_CLK_ARES				150
+#define GCC_Q6SS_DBG_ARES				151
+#define GCC_WCSS_DBG_BDG_ARES				152
+#define GCC_WCSS_DBG_ARES				153
+#define GCC_WCSS_AXI_S_ARES				154
+#define GCC_WCSS_AXI_M_ARES				155
+#define GCC_WCSSAON_ARES				156
+#define GCC_PCIE3X2_PIPE_ARES				157
+#define GCC_PCIE3X2_CORE_STICKY_ARES			158
+#define GCC_PCIE3X2_AXI_S_STICKY_ARES			159
+#define GCC_PCIE3X2_AXI_M_STICKY_ARES			160
+#define GCC_PCIE3X1_0_PIPE_ARES				161
+#define GCC_PCIE3X1_0_CORE_STICKY_ARES			162
+#define GCC_PCIE3X1_0_AXI_S_STICKY_ARES			163
+#define GCC_PCIE3X1_0_AXI_M_STICKY_ARES			164
+#define GCC_PCIE3X1_1_PIPE_ARES				165
+#define GCC_PCIE3X1_1_CORE_STICKY_ARES			166
+#define GCC_PCIE3X1_1_AXI_S_STICKY_ARES			167
+#define GCC_PCIE3X1_1_AXI_M_STICKY_ARES			168
+#define GCC_IM_SLEEP_CLK_ARES				169
+#define GCC_NSSNOC_PCNOC_1_CLK_ARES			170
+#define GCC_UNIPHY0_XPCS_ARES				171
+#define GCC_UNIPHY1_XPCS_ARES				172
+#endif
-- 
2.17.1

[PATCH V6 5/9] clk: qcom: ipq5332: mark GPLL4 as ignore unused temporarily

[Kathiravan T]

Clock framework disables the GPLL4 source since there are no active users
for this source currently. Some of the clocks initialized by the
bootloaders uses the GPLL4 as the source. Due to this, when the GPLL4 is
disabled by the clock framework, system is going for the reboot.

To avoid this, mark the GPLL4 as ignore unused so that clock framework
doesn't disable it. Once the users of this source is enabled, we can get
rid of this flag.

Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
---
Changes in V6:
	- Newly added this patch in V6, to keep the dependent patches
	  together

 drivers/clk/qcom/gcc-ipq5332.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/clk/qcom/gcc-ipq5332.c b/drivers/clk/qcom/gcc-ipq5332.c
index 9e4baea33937..bdb4a0a11d07 100644
--- a/drivers/clk/qcom/gcc-ipq5332.c
+++ b/drivers/clk/qcom/gcc-ipq5332.c
@@ -128,6 +128,17 @@ static struct clk_alpha_pll gpll4_main = {
 			.parent_data = &gcc_parent_data_xo,
 			.num_parents = 1,
 			.ops = &clk_alpha_pll_stromer_ops,
+			/*
+			 * There are no consumers for this GPLL in kernel yet,
+			 * (will be added soon), so the clock framework
+			 * disables this source. But some of the clocks
+			 * initialized by boot loaders uses this source. So we
+			 * need to keep this clock ON. Add the
+			 * CLK_IGNORE_UNUSED flag so the clock will not be
+			 * disabled. Once the consumer in kernel is added, we
+			 * can get rid of this flag.
+			 */
+			.flags = CLK_IGNORE_UNUSED,
 		},
 	},
 };
-- 
2.17.1

[PATCH V6 6/9] dt-bindings: qcom: add ipq5332 boards

[Kathiravan T]

Document the new ipq5332 SoC/board device tree bindings

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
---
Changes in V6:
	- No changes

Changes in V5:
	- No changes

Changes in V4:
	- Pick up R-b tag

Changes in V3:
	- Sorted the board name

Changes in V2:
	- No changes

 Documentation/devicetree/bindings/arm/qcom.yaml | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 1bb24d46e4ee..465bb98cb91d 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -30,6 +30,7 @@ description: |
         apq8084
         apq8096
         ipq4018
+        ipq5332
         ipq6018
         ipq8074
         mdm9615
@@ -80,6 +81,7 @@ description: |
   The 'board' element must be one of the following strings:
 
         adp
+        ap-mi01.2
         cdp
         cp01-c1
         dragonboard
@@ -320,6 +322,11 @@ properties:
               - qcom,ipq4019-dk04.1-c1
           - const: qcom,ipq4019
 
+      - items:
+          - enum:
+              - qcom,ipq5332-ap-mi01.2
+          - const: qcom,ipq5332
+
       - items:
           - enum:
               - mikrotik,rb3011
-- 
2.17.1

[PATCH V6 7/9] dt-bindings: firmware: qcom,scm: document IPQ5332 SCM

[Kathiravan T]

Document the compatible for IPQ5332 SCM.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
---
Changes in V6:
	- No changes

Changes in V5:
	- No changes

Changes in V4:
	- No changes

Changes in V3:
	- No changes

Changes in V2:
	- Added the 'Acked-by' tag

 Documentation/devicetree/bindings/firmware/qcom,scm.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
index a66e99812b1f..c1adbb83734b 100644
--- a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
+++ b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
@@ -24,6 +24,7 @@ properties:
           - qcom,scm-apq8064
           - qcom,scm-apq8084
           - qcom,scm-ipq4019
+          - qcom,scm-ipq5332
           - qcom,scm-ipq6018
           - qcom,scm-ipq806x
           - qcom,scm-ipq8074
-- 
2.17.1

[PATCH V6 8/9] arm64: dts: qcom: add IPQ5332 SoC and MI01.2 board support

[Kathiravan T]

Add initial device tree support for the Qualcomm IPQ5332 SoC and
MI01.2 board.

Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
---
Changes in V6:
	- No changes

Changes in V5:
	- Dropped the clock-names property in GCC node

Changes in V4:
	- No changes

Changes in V3:
	- Updated the V2M node name to reflect the proper address
	- In reserved-memory node, changed the order of the 'reg' and
	  'no-map' property
	- Moved the below properties to the board DTS
		bus-width = <4>;
		max-frequency = <192000000>;
		mmc-ddr-1_8v;
		mmc-hs200-1_8v;

Changes in V2:
	- Changed the license to BSD3 in the file ipq5332-mi01.2.dts
	- Updated the model name, not to include the foundry ID
	- Used the decimal notation instead of hex for 'cache-level'
	  property
	- Dropped the blank line
	- Updated the node name for the TZ reserved region
	- Moved the 'compatible' property as first one in the node,
	  wherever applicable
	- Used the decimal notation for *-cells property insrtead of
	  hex
	- Reorganised the properties of memory mapped timer node as
	  below
		- reg
		- interrupts
		- frame-number
	- Fixed the indentation in timer node

 arch/arm64/boot/dts/qcom/Makefile           |   1 +
 arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts |  75 ++++++
 arch/arm64/boot/dts/qcom/ipq5332.dtsi       | 263 ++++++++++++++++++++
 3 files changed, 339 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
 create mode 100644 arch/arm64/boot/dts/qcom/ipq5332.dtsi

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 31aa54f0428c..cfebb1b3c2a2 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= apq8016-sbc.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8094-sony-xperia-kitakami-karin_windy.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8096-db820c.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8096-ifc6640.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= ipq5332-mi01.2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq6018-cp01-c1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk01.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk10-c1.dtb
diff --git a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
new file mode 100644
index 000000000000..702013b867d7
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * IPQ5332 AP-MI01.2 board device tree source
+ *
+ * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "ipq5332.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ5332 MI01.2";
+	compatible = "qcom,ipq5332-ap-mi01.2", "qcom,ipq5332";
+
+	aliases {
+		serial0 = &blsp1_uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+};
+
+&blsp1_uart0 {
+	pinctrl-0 = <&serial_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&sdhc {
+	bus-width = <4>;
+	max-frequency = <192000000>;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	non-removable;
+	pinctrl-0 = <&sdc_default_state>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&sleep_clk {
+	clock-frequency = <32000>;
+};
+
+&xo_board {
+	clock-frequency = <24000000>;
+};
+
+/* PINCTRL */
+
+&tlmm {
+	sdc_default_state: sdc-default-state {
+		clk-pins {
+			pins = "gpio13";
+			function = "sdc_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		cmd-pins {
+			pins = "gpio12";
+			function = "sdc_cmd";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		data-pins {
+			pins = "gpio8", "gpio9", "gpio10", "gpio11";
+			function = "sdc_data";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi b/arch/arm64/boot/dts/qcom/ipq5332.dtsi
new file mode 100644
index 000000000000..a2ed54264d5c
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi
@@ -0,0 +1,263 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * IPQ5332 device tree source
+ *
+ * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,ipq5332-gcc.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	interrupt-parent = <&intc>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	clocks {
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
+
+		xo_board: xo-board-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			enable-method = "psci";
+			next-level-cache = <&L2_0>;
+		};
+
+		CPU1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x1>;
+			enable-method = "psci";
+			next-level-cache = <&L2_0>;
+		};
+
+		CPU2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x2>;
+			enable-method = "psci";
+			next-level-cache = <&L2_0>;
+		};
+
+		CPU3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x3>;
+			enable-method = "psci";
+			next-level-cache = <&L2_0>;
+		};
+
+		L2_0: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-ipq5332", "qcom,scm";
+		};
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the size */
+		reg = <0x0 0x40000000 0x0 0x0>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		tz_mem: tz@4a600000 {
+			reg = <0x0 0x4a600000 0x0 0x200000>;
+			no-map;
+		};
+	};
+
+	soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0 0xffffffff>;
+
+		tlmm: pinctrl@1000000 {
+			compatible = "qcom,ipq5332-tlmm";
+			reg = <0x01000000 0x300000>;
+			interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 53>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			serial_0_pins: serial0-state {
+				pins = "gpio18", "gpio19";
+				function = "blsp0_uart0";
+				drive-strength = <8>;
+				bias-pull-up;
+			};
+		};
+
+		gcc: clock-controller@1800000 {
+			compatible = "qcom,ipq5332-gcc";
+			reg = <0x01800000 0x80000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			clocks = <&xo_board>,
+				 <&sleep_clk>,
+				 <0>,
+				 <0>,
+				 <0>;
+		};
+
+		sdhc: mmc@7804000 {
+			compatible = "qcom,ipq5332-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0x07804000 0x1000>, <0x07805000 0x1000>;
+
+			interrupts = <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			status = "disabled";
+		};
+
+		blsp1_uart0: serial@78af000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078af000 0x200>;
+			interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		intc: interrupt-controller@b000000 {
+			compatible = "qcom,msm-qgic2";
+			reg = <0x0b000000 0x1000>,	/* GICD */
+			      <0x0b002000 0x1000>,	/* GICC */
+			      <0x0b001000 0x1000>,	/* GICH */
+			      <0x0b004000 0x1000>;	/* GICV */
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x0b00c000 0x3000>;
+
+			v2m0: v2m@0 {
+				compatible = "arm,gic-v2m-frame";
+				reg = <0x00000000 0xffd>;
+				msi-controller;
+			};
+
+			v2m1: v2m@1000 {
+				compatible = "arm,gic-v2m-frame";
+				reg = <0x00001000 0xffd>;
+				msi-controller;
+			};
+
+			v2m2: v2m@2000 {
+				compatible = "arm,gic-v2m-frame";
+				reg = <0x00002000 0xffd>;
+				msi-controller;
+			};
+		};
+
+		timer@b120000 {
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x0b120000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			frame@b120000 {
+				reg = <0x0b121000 0x1000>,
+				      <0x0b122000 0x1000>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <0>;
+			};
+
+			frame@b123000 {
+				reg = <0x0b123000 0x1000>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <1>;
+				status = "disabled";
+			};
+
+			frame@b124000 {
+				reg = <0x0b124000 0x1000>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <2>;
+				status = "disabled";
+			};
+
+			frame@b125000 {
+				reg = <0x0b125000 0x1000>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <3>;
+				status = "disabled";
+			};
+
+			frame@b126000 {
+				reg = <0x0b126000 0x1000>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <4>;
+				status = "disabled";
+			};
+
+			frame@b127000 {
+				reg = <0x0b127000 0x1000>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <5>;
+				status = "disabled";
+			};
+
+			frame@b128000 {
+				reg = <0x0b128000 0x1000>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <6>;
+				status = "disabled";
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
-- 
2.17.1

[PATCH V6 9/9] arm64: defconfig: Enable IPQ5332 SoC base configs

[Kathiravan T]

Enable the clock and pinctrl configs for Qualcomm IPQ5332 SoC

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
---
Changed in V6:
	- No changes

Changed in V5:
	- No changes

Changed in V4:
	- Pick up R-b tag

Changes in V3:
	- Updated the commit message

Changed in V2:
	- No changes

 arch/arm64/configs/defconfig | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 7790ee42c68a..4a8b3f5e07be 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -545,6 +545,7 @@ CONFIG_PINCTRL_IMX8ULP=y
 CONFIG_PINCTRL_IMX93=y
 CONFIG_PINCTRL_MSM=y
 CONFIG_PINCTRL_IPQ8074=y
+CONFIG_PINCTRL_IPQ5332=y
 CONFIG_PINCTRL_IPQ6018=y
 CONFIG_PINCTRL_MSM8916=y
 CONFIG_PINCTRL_MSM8953=y
@@ -1122,6 +1123,7 @@ CONFIG_QCOM_CLK_APCS_MSM8916=y
 CONFIG_QCOM_CLK_APCC_MSM8996=y
 CONFIG_QCOM_CLK_SMD_RPM=y
 CONFIG_QCOM_CLK_RPMH=y
+CONFIG_IPQ_GCC_5332=y
 CONFIG_IPQ_GCC_6018=y
 CONFIG_IPQ_GCC_8074=y
 CONFIG_MSM_GCC_8916=y
-- 
2.17.1

Re: [PATCH V6 7/9] dt-bindings: firmware: qcom,scm: document IPQ5332 SCM

[Konrad Dybcio]

On 7.03.2023 07:22, Kathiravan T wrote:
> Document the compatible for IPQ5332 SCM.
> 
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
> ---
Does this board not have a crypto engine / CE1 clock exposed via
RPMCC? It will be enabled by default, but Linux should be aware
of it, so that we don't gate it by accident.

Konrad
> Changes in V6:
> 	- No changes
> 
> Changes in V5:
> 	- No changes
> 
> Changes in V4:
> 	- No changes
> 
> Changes in V3:
> 	- No changes
> 
> Changes in V2:
> 	- Added the 'Acked-by' tag
> 
>  Documentation/devicetree/bindings/firmware/qcom,scm.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
> index a66e99812b1f..c1adbb83734b 100644
> --- a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
> +++ b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
> @@ -24,6 +24,7 @@ properties:
>            - qcom,scm-apq8064
>            - qcom,scm-apq8084
>            - qcom,scm-ipq4019
> +          - qcom,scm-ipq5332
>            - qcom,scm-ipq6018
>            - qcom,scm-ipq806x
>            - qcom,scm-ipq8074

Re: [PATCH V6 7/9] dt-bindings: firmware: qcom,scm: document IPQ5332 SCM

[Kathiravan T]

On 3/8/2023 4:31 PM, Konrad Dybcio wrote:
>
> On 7.03.2023 07:22, Kathiravan T wrote:
>> Document the compatible for IPQ5332 SCM.
>>
>> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>> Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
>> ---
> Does this board not have a crypto engine / CE1 clock exposed via
> RPMCC? It will be enabled by default, but Linux should be aware
> of it, so that we don't gate it by accident.


IPQ5332 doesn't have the crypto engine and also it doesn't have RPMCC. 
Sorry, could you please help to explain how it is related to SCM?

Thanks, Kathiravan T.

Re: [PATCH V6 7/9] dt-bindings: firmware: qcom,scm: document IPQ5332 SCM

[Konrad Dybcio]

On 8.03.2023 16:39, Kathiravan T wrote:
> 
> On 3/8/2023 4:31 PM, Konrad Dybcio wrote:
>>
>> On 7.03.2023 07:22, Kathiravan T wrote:
>>> Document the compatible for IPQ5332 SCM.
>>>
>>> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>>> Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
>>> ---
>> Does this board not have a crypto engine / CE1 clock exposed via
>> RPMCC? It will be enabled by default, but Linux should be aware
>> of it, so that we don't gate it by accident.
> 
> 
> IPQ5332 doesn't have the crypto engine and also it doesn't have RPMCC. Sorry, could you please help to explain how it is related to SCM?
SCM usually requires certain clocks to be up and that often includes
the CE1 clock on fairly recent designs.

Konrad
> 
> Thanks, Kathiravan T.

Re: [PATCH V6 7/9] dt-bindings: firmware: qcom,scm: document IPQ5332 SCM

[Kathiravan T]

On 3/8/2023 9:14 PM, Konrad Dybcio wrote:
>
> On 8.03.2023 16:39, Kathiravan T wrote:
>> On 3/8/2023 4:31 PM, Konrad Dybcio wrote:
>>> On 7.03.2023 07:22, Kathiravan T wrote:
>>>> Document the compatible for IPQ5332 SCM.
>>>>
>>>> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>>>> Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
>>>> ---
>>> Does this board not have a crypto engine / CE1 clock exposed via
>>> RPMCC? It will be enabled by default, but Linux should be aware
>>> of it, so that we don't gate it by accident.
>>
>> IPQ5332 doesn't have the crypto engine and also it doesn't have RPMCC. Sorry, could you please help to explain how it is related to SCM?
> SCM usually requires certain clocks to be up and that often includes
> the CE1 clock on fairly recent designs.


Thanks for the explanation. I don't see such requirements for this SoC.


> Konrad
>> Thanks, Kathiravan T.

Re: (subset) [PATCH V6 0/9] Add minimal boot support for IPQ5332

[Bjorn Andersson]

On Tue, 7 Mar 2023 11:52:23 +0530, Kathiravan T wrote:
> The IPQ5332 is Qualcomm's 802.11be SoC for Routers, Gateways and
> Access Points.
> 
> This series adds minimal board boot support for ipq5332-mi01.2 board.
> 
> Changes in V6:
> 	- Added couple of patches 1/9 and 5/9 in the series to make sure
> 	  all the dependent patches are together
> 	- V5 can be found at
> 	  https://lore.kernel.org/linux-arm-msm/20230217075835.460-1-quic_kathirav@quicinc.com/
> 
> [...]

Applied, thanks!

[9/9] arm64: defconfig: Enable IPQ5332 SoC base configs
      commit: 48adb3be7d617ecc7d9656032e7253406b8040f5

Best regards,
-- 
Bjorn Andersson <andersson@kernel.org>