* [PATCH v2 0/5] RB1 + QCM2290 support
@ 2023-04-05 15:50 Konrad Dybcio
2023-04-05 15:50 ` [PATCH v2 1/5] dt-bindings: firmware: document Qualcomm QCM2290 SCM Konrad Dybcio
` (5 more replies)
0 siblings, 6 replies; 10+ messages in thread
From: Konrad Dybcio @ 2023-04-05 15:50 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Robert Marko, Das Srinagesh
Cc: Bhupesh Sharma, Vladimir Zapolskiy, Marijn Suijten,
linux-arm-msm, devicetree, linux-kernel, Konrad Dybcio,
Krzysztof Kozlowski
v1 -> v2:
- Fix missing newline in pm2250.dtsi
- Use an enum in [2/5] to allow for more QRB2210 boards
- Squash the dt patches into one per SoC, PMIC and board
- pick up rb on [1/5]
v1: https://lore.kernel.org/r/20230403-topic-rb1_qcm-v1-0-ca849b62ba07@linaro.org
This series brings basic support for the Qualcomm Robotics RB1 board,
including but not limited to:
- TSENS-connected thermal management
- USB2
- eMMC (uSD depends requires regulators to work, will be sent separately)
- the necessary plumbing for *DSP + Wi-Fi (that also needs regulators)
- buttons
A compatible in the SCM C driver is not added on purpose, as:
1. it's not neccessary before we figure out disabling rpmcc, the dt
part is in regardless (the clock it consumes is always-on today)
2. a point to get rid of SoC-specific compatibles in there was raised
See also:
https://www.thundercomm.com/product/qualcomm-robotics-rb1-platform/
https://www.qualcomm.com/products/internet-of-things/industrial/industrial-automation/qualcomm-robotics-rb1-platform
Dependencies:
- https://lore.kernel.org/linux-arm-msm/20230314-topic-2290_compats-v1-0-47e26c3c0365@linaro.org/
- https://lore.kernel.org/linux-arm-msm/20230315183231.3562580-1-konrad.dybcio@linaro.org/
- https://lore.kernel.org/linux-arm-msm/20230323173019.3706069-1-dianders@chromium.org/
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
Konrad Dybcio (5):
dt-bindings: firmware: document Qualcomm QCM2290 SCM
dt-bindings: arm: qcom: Add QRB2210/QCM2290 and RB1 board
arm64: dts: qcom: Add initial QCM2290 device tree
arm64: dts: qcom: Add initial PM2250 device tree
arm64: dts: qcom: Add initial QTI RB1 device tree
Documentation/devicetree/bindings/arm/qcom.yaml | 9 +
.../devicetree/bindings/firmware/qcom,scm.yaml | 3 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/pm2250.dtsi | 63 +
arch/arm64/boot/dts/qcom/qcm2290.dtsi | 1561 ++++++++++++++++++++
arch/arm64/boot/dts/qcom/qrb2210-rb1.dts | 112 ++
6 files changed, 1749 insertions(+)
---
base-commit: 8417c8f5007bf4567ccffda850a3157c7d905f67
change-id: 20230403-topic-rb1_qcm-78a8826b34b6
Best regards,
--
Konrad Dybcio <konrad.dybcio@linaro.org>
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v2 1/5] dt-bindings: firmware: document Qualcomm QCM2290 SCM
2023-04-05 15:50 [PATCH v2 0/5] RB1 + QCM2290 support Konrad Dybcio
@ 2023-04-05 15:50 ` Konrad Dybcio
2023-04-05 15:50 ` [PATCH v2 2/5] dt-bindings: arm: qcom: Add QRB2210/QCM2290 and RB1 board Konrad Dybcio
` (4 subsequent siblings)
5 siblings, 0 replies; 10+ messages in thread
From: Konrad Dybcio @ 2023-04-05 15:50 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Robert Marko, Das Srinagesh
Cc: Bhupesh Sharma, Vladimir Zapolskiy, Marijn Suijten,
linux-arm-msm, devicetree, linux-kernel, Konrad Dybcio,
Krzysztof Kozlowski
Add a compatible for Qualcomm QCM2290 SCM and add it to the core clock
users list.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
Documentation/devicetree/bindings/firmware/qcom,scm.yaml | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
index 543feb3b6c58..35540f292bfd 100644
--- a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
+++ b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
@@ -40,6 +40,7 @@ properties:
- qcom,scm-msm8994
- qcom,scm-msm8996
- qcom,scm-msm8998
+ - qcom,scm-qcm2290
- qcom,scm-qdu1000
- qcom,scm-sa8775p
- qcom,scm-sc7180
@@ -109,6 +110,7 @@ allOf:
- qcom,scm-msm8960
- qcom,scm-msm8974
- qcom,scm-msm8976
+ - qcom,scm-qcm2290
- qcom,scm-sm6375
then:
required:
@@ -127,6 +129,7 @@ allOf:
- qcom,scm-apq8064
- qcom,scm-msm8660
- qcom,scm-msm8960
+ - qcom,scm-qcm2290
- qcom,scm-sm6375
then:
properties:
--
2.40.0
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 2/5] dt-bindings: arm: qcom: Add QRB2210/QCM2290 and RB1 board
2023-04-05 15:50 [PATCH v2 0/5] RB1 + QCM2290 support Konrad Dybcio
2023-04-05 15:50 ` [PATCH v2 1/5] dt-bindings: firmware: document Qualcomm QCM2290 SCM Konrad Dybcio
@ 2023-04-05 15:50 ` Konrad Dybcio
2023-04-07 18:59 ` Krzysztof Kozlowski
2023-04-05 15:50 ` [PATCH v2 3/5] arm64: dts: qcom: Add initial QCM2290 device tree Konrad Dybcio
` (3 subsequent siblings)
5 siblings, 1 reply; 10+ messages in thread
From: Konrad Dybcio @ 2023-04-05 15:50 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Robert Marko, Das Srinagesh
Cc: Bhupesh Sharma, Vladimir Zapolskiy, Marijn Suijten,
linux-arm-msm, devicetree, linux-kernel, Konrad Dybcio
Document QRB210, a QRB version of QCM2290.
Document QTI Robotics RB1 as a QRB2210 device.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 05badce5fedc..236ea55aee96 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -47,6 +47,8 @@ description: |
msm8996
msm8998
qcs404
+ qcm2290
+ qrb2210
qdu1000
qru1000
sa8155p
@@ -353,6 +355,13 @@ properties:
- const: swir,wp8548
- const: qcom,mdm9615
+ - description: Qualcomm Technologies, Inc. Robotics RB1
+ items:
+ - enum:
+ - qcom,qrb2210-rb1
+ - const: qcom,qrb2210
+ - const: qcom,qcm2290
+
- description: Qualcomm Technologies, Inc. Distributed Unit 1000 platform
items:
- enum:
--
2.40.0
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 3/5] arm64: dts: qcom: Add initial QCM2290 device tree
2023-04-05 15:50 [PATCH v2 0/5] RB1 + QCM2290 support Konrad Dybcio
2023-04-05 15:50 ` [PATCH v2 1/5] dt-bindings: firmware: document Qualcomm QCM2290 SCM Konrad Dybcio
2023-04-05 15:50 ` [PATCH v2 2/5] dt-bindings: arm: qcom: Add QRB2210/QCM2290 and RB1 board Konrad Dybcio
@ 2023-04-05 15:50 ` Konrad Dybcio
2023-04-07 18:35 ` Bjorn Andersson
2023-04-05 15:50 ` [PATCH v2 4/5] arm64: dts: qcom: Add initial PM2250 " Konrad Dybcio
` (2 subsequent siblings)
5 siblings, 1 reply; 10+ messages in thread
From: Konrad Dybcio @ 2023-04-05 15:50 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Robert Marko, Das Srinagesh
Cc: Bhupesh Sharma, Vladimir Zapolskiy, Marijn Suijten,
linux-arm-msm, devicetree, linux-kernel, Konrad Dybcio
Add an initial device tree for the QCM2290 low-end SoC, featuring 4
"customized" Cortex-A53 cores and up to 4 GiB of LPDDR(3/4X).
This revision brings support for:
- TSENS & thermal zones
- SDHCI1/2
- I2C, SPI, UART
- MPSS
- ADSP
- Wi-Fi
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/qcm2290.dtsi | 1561 +++++++++++++++++++++++++++++++++
2 files changed, 1562 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 1a29403400b7..6fc8d6664f0c 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -70,6 +70,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-xiaomi-sagit.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
+dtb-$(CONFIG_ARCH_QCOM) += qrb2210-rb1.dtb
dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5-vision-mezzanine.dtb
dtb-$(CONFIG_ARCH_QCOM) += qru1000-idp.dtb
diff --git a/arch/arm64/boot/dts/qcom/qcm2290.dtsi b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
new file mode 100644
index 000000000000..ae5abc76bcc7
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
@@ -0,0 +1,1561 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) 2023, Linaro Ltd
+ *
+ * Based on sm6115.dtsi and previous efforts by Shawn Guo & Loic Poulain.
+ */
+
+#include <dt-bindings/clock/qcom,gcc-qcm2290.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/dma/qcom-gpi.h>
+#include <dt-bindings/firmware/qcom,scm.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+
+/ {
+ interrupt-parent = <&intc>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ chosen { };
+
+ clocks {
+ xo_board: xo-board {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
+
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32764>;
+ #clock-cells = <0>;
+ };
+ };
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ CPU0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0 0x0>;
+ clocks = <&cpufreq_hw 0>;
+ capacity-dmips-mhz = <1024>;
+ dynamic-power-coefficient = <100>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
+ L2_0: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ CPU1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0 0x1>;
+ clocks = <&cpufreq_hw 0>;
+ capacity-dmips-mhz = <1024>;
+ dynamic-power-coefficient = <100>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
+ };
+
+ CPU2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0 0x2>;
+ clocks = <&cpufreq_hw 0>;
+ capacity-dmips-mhz = <1024>;
+ dynamic-power-coefficient = <100>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
+ };
+
+ CPU3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0 0x3>;
+ clocks = <&cpufreq_hw 0>;
+ capacity-dmips-mhz = <1024>;
+ dynamic-power-coefficient = <100>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&CPU0>;
+ };
+
+ core1 {
+ cpu = <&CPU1>;
+ };
+
+ core2 {
+ cpu = <&CPU2>;
+ };
+
+ core3 {
+ cpu = <&CPU3>;
+ };
+ };
+ };
+ };
+
+ firmware {
+ scm: scm {
+ compatible = "qcom,scm-qcm2290", "qcom,scm";
+ clocks = <&rpmcc RPM_SMD_CE1_CLK>;
+ clock-names = "core";
+ #reset-cells = <1>;
+ };
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the size */
+ reg = <0 0x40000000 0 0>;
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ reserved_memory: reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ hyp_mem: hyp@45700000 {
+ reg = <0x0 0x45700000 0x0 0x600000>;
+ no-map;
+ };
+
+ xbl_aop_mem: xbl-aop@45e00000 {
+ reg = <0x0 0x45e00000 0x0 0x140000>;
+ no-map;
+ };
+
+ sec_apps_mem: sec-apps@45fff000 {
+ reg = <0x0 0x45fff000 0x0 0x1000>;
+ no-map;
+ };
+
+ smem_mem: smem@46000000 {
+ compatible = "qcom,smem";
+ reg = <0x0 0x46000000 0x0 0x200000>;
+ no-map;
+
+ hwlocks = <&tcsr_mutex 3>;
+ qcom,rpm-msg-ram = <&rpm_msg_ram>;
+ };
+
+ pil_modem_mem: modem@4ab00000 {
+ reg = <0x0 0x4ab00000 0x0 0x6900000>;
+ no-map;
+ };
+
+ pil_video_mem: video@51400000 {
+ reg = <0x0 0x51400000 0x0 0x500000>;
+ no-map;
+ };
+
+ wlan_msa_mem: wlan-msa@51900000 {
+ reg = <0x0 0x51900000 0x0 0x100000>;
+ no-map;
+ };
+
+ pil_adsp_mem: adsp@51a00000 {
+ reg = <0x0 0x51a00000 0x0 0x1c00000>;
+ no-map;
+ };
+
+ pil_ipa_fw_mem: ipa-fw@53600000 {
+ reg = <0x0 0x53600000 0x0 0x10000>;
+ no-map;
+ };
+
+ pil_ipa_gsi_mem: ipa-gsi@53610000 {
+ reg = <0x0 0x53610000 0x0 0x5000>;
+ no-map;
+ };
+
+ pil_gpu_mem: zap@53615000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0x53615000 0x0 0x2000>;
+ no-map;
+ };
+
+ cont_splash_memory: framebuffer@5c000000 {
+ reg = <0x0 0x5c000000 0x0 0x00f00000>;
+ no-map;
+ };
+
+ dfps_data_memory: dpfs-data@5cf00000 {
+ reg = <0x0 0x5cf00000 0x0 0x0100000>;
+ no-map;
+ };
+
+ removed_mem: reserved@60000000 {
+ reg = <0x0 0x60000000 0x0 0x3900000>;
+ no-map;
+ };
+
+ rmtfs_mem: memory@89b01000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0x0 0x89b01000 0x0 0x200000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ qcom,vmid = <QCOM_SCM_VMID_MSS_MSA QCOM_SCM_VMID_NAV>;
+ };
+ };
+
+ rpm-glink {
+ compatible = "qcom,glink-rpm";
+ interrupts = <GIC_SPI 194 IRQ_TYPE_EDGE_RISING>;
+ qcom,rpm-msg-ram = <&rpm_msg_ram>;
+ mboxes = <&apcs_glb 0>;
+
+ rpm_requests: rpm-requests {
+ compatible = "qcom,rpm-qcm2290";
+ qcom,glink-channels = "rpm_requests";
+
+ rpmcc: clock-controller {
+ compatible = "qcom,rpmcc-qcm2290", "qcom,rpmcc";
+ clocks = <&xo_board>;
+ clock-names = "xo";
+ #clock-cells = <1>;
+ };
+
+ rpmpd: power-controller {
+ compatible = "qcom,qcm2290-rpmpd";
+ #power-domain-cells = <1>;
+ operating-points-v2 = <&rpmpd_opp_table>;
+
+ rpmpd_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ rpmpd_opp_min_svs: opp1 {
+ opp-level = <RPM_SMD_LEVEL_MIN_SVS>;
+ };
+
+ rpmpd_opp_low_svs: opp2 {
+ opp-level = <RPM_SMD_LEVEL_LOW_SVS>;
+ };
+
+ rpmpd_opp_svs: opp3 {
+ opp-level = <RPM_SMD_LEVEL_SVS>;
+ };
+
+ rpmpd_opp_svs_plus: opp4 {
+ opp-level = <RPM_SMD_LEVEL_SVS_PLUS>;
+ };
+
+ rpmpd_opp_nom: opp5 {
+ opp-level = <RPM_SMD_LEVEL_NOM>;
+ };
+
+ rpmpd_opp_nom_plus: opp6 {
+ opp-level = <RPM_SMD_LEVEL_NOM_PLUS>;
+ };
+
+ rpmpd_opp_turbo: opp7 {
+ opp-level = <RPM_SMD_LEVEL_TURBO>;
+ };
+
+ rpmpd_opp_turbo_plus: opp8 {
+ opp-level = <RPM_SMD_LEVEL_TURBO_NO_CPR>;
+ };
+ };
+ };
+ };
+ };
+
+ smp2p-adsp {
+ compatible = "qcom,smp2p";
+ qcom,smem = <443>, <429>;
+
+ interrupts = <GIC_SPI 279 IRQ_TYPE_EDGE_RISING>;
+
+ mboxes = <&apcs_glb 10>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <2>;
+
+ adsp_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ adsp_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ smp2p-mpss {
+ compatible = "qcom,smp2p";
+ qcom,smem = <435>, <428>;
+
+ interrupts = <GIC_SPI 70 IRQ_TYPE_EDGE_RISING>;
+
+ mboxes = <&apcs_glb 14>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <1>;
+
+ modem_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ modem_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ wlan_smp2p_in: wlan-wpss-to-ap {
+ qcom,entry-name = "wlan";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ soc: soc@0 {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0 0 0 0 0x10 0>;
+ dma-ranges = <0 0 0 0 0x10 0>;
+
+ tcsr_mutex: hwlock@340000 {
+ compatible = "qcom,tcsr-mutex";
+ reg = <0x0 0x00340000 0x0 0x20000>;
+ #hwlock-cells = <1>;
+ };
+
+ tlmm: pinctrl@500000 {
+ compatible = "qcom,qcm2290-tlmm";
+ reg = <0x0 0x00500000 0x0 0x300000>;
+ interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ gpio-ranges = <&tlmm 0 0 127>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ qup_i2c0_default: qup-i2c0-default-state {
+ pins = "gpio0", "gpio1";
+ function = "qup0";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c1_default: qup-i2c1-default-state {
+ pins = "gpio4", "gpio5";
+ function = "qup1";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c2_default: qup-i2c2-default-state {
+ pins = "gpio6", "gpio7";
+ function = "qup2";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c3_default: qup-i2c3-default-state {
+ pins = "gpio8", "gpio9";
+ function = "qup3";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c4_default: qup-i2c4-default-state {
+ pins = "gpio12", "gpio13";
+ function = "qup4";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c5_default: qup-i2c5-default-state {
+ pins = "gpio14", "gpio15";
+ function = "qup5";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi0_default: qup-spi0-default-state {
+ pins = "gpio0", "gpio1","gpio2", "gpio3";
+ function = "qup0";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi1_default: qup-spi1-default-state {
+ pins = "gpio4", "gpio5", "gpio69", "gpio70";
+ function = "qup1";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi2_default: qup-spi2-default-state {
+ pins = "gpio6", "gpio7", "gpio71", "gpio80";
+ function = "qup2";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi3_default: qup-spi3-default-state {
+ pins = "gpio8", "gpio9", "gpio10", "gpio11";
+ function = "qup3";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi4_default: qup-spi4-default-state {
+ pins = "gpio12", "gpio13", "gpio96", "gpio97";
+ function = "qup4";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi5_default: qup-spi5-default-state {
+ pins = "gpio14", "gpio15", "gpio16", "gpio17";
+ function = "qup5";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_uart0_default: qup-uart0-default-state {
+ pins = "gpio0", "gpio1", "gpio2", "gpio3";
+ function = "qup0";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ qup_uart4_default: qup-uart4-default-state {
+ pins = "gpio12", "gpio13";
+ function = "qup4";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ sdc1_state_on: sdc1-on-state {
+ clk-pins {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ cmd-pins {
+ pins = "sdc1_cmd";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ data-pins {
+ pins = "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ rclk-pins {
+ pins = "sdc1_rclk";
+ bias-pull-down;
+ };
+ };
+
+ sdc1_state_off: sdc1-off-state {
+ clk-pins {
+ pins = "sdc1_clk";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ cmd-pins {
+ pins = "sdc1_cmd";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ data-pins {
+ pins = "sdc1_data";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ rclk-pins {
+ pins = "sdc1_rclk";
+ bias-pull-down;
+ };
+ };
+
+ sdc2_state_on: sdc2-on-state {
+ clk-pins {
+ pins = "sdc2_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ cmd-pins {
+ pins = "sdc2_cmd";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ data-pins {
+ pins = "sdc2_data";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ sdc2_state_off: sdc2-off-state {
+ clk-pins {
+ pins = "sdc2_clk";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ cmd-pins {
+ pins = "sdc2_cmd";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ data-pins {
+ pins = "sdc2_data";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+ };
+
+ gcc: clock-controller@1400000 {
+ compatible = "qcom,gcc-qcm2290";
+ reg = <0x0 0x01400000 0x0 0x1f0000>;
+ clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, <&sleep_clk>;
+ clock-names = "bi_tcxo", "sleep_clk";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+
+ usb_hsphy: phy@1613000 {
+ compatible = "qcom,qcm2290-qusb2-phy";
+ reg = <0x0 0x01613000 0x0 0x180>;
+
+ clocks = <&gcc GCC_AHB2PHY_USB_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+ nvmem-cells = <&qusb2_hstx_trim>;
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ qfprom@1b44000 {
+ compatible = "qcom,qcm2290-qfprom", "qcom,qfprom";
+ reg = <0x0 0x01b44000 0x0 0x3000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qusb2_hstx_trim: hstx-trim@25b {
+ reg = <0x25b 0x1>;
+ bits = <1 4>;
+ };
+ };
+
+ spmi_bus: spmi@1c40000 {
+ compatible = "qcom,spmi-pmic-arb";
+ reg = <0x0 0x01c40000 0x0 0x1100>,
+ <0x0 0x01e00000 0x0 0x2000000>,
+ <0x0 0x03e00000 0x0 0x100000>,
+ <0x0 0x03f00000 0x0 0xa0000>,
+ <0x0 0x01c0a000 0x0 0x26000>;
+ reg-names = "core",
+ "chnls",
+ "obsrvr",
+ "intr",
+ "cnfg";
+ interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "periph_irq";
+ qcom,ee = <0>;
+ qcom,channel = <0>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <4>;
+ };
+
+ tsens0: thermal-sensor@4411000 {
+ compatible = "qcom,qcm2290-tsens", "qcom,tsens-v2";
+ reg = <0x0 0x04411000 0x0 0x1ff>,
+ <0x0 0x04410000 0x0 0x8>;
+ #qcom,sensors = <10>;
+ interrupts = <GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow", "critical";
+ #thermal-sensor-cells = <1>;
+ };
+
+ rng: rng@4453000 {
+ compatible = "qcom,prng-ee";
+ reg = <0x0 0x04453000 0x0 0x1000>;
+ clocks = <&rpmcc RPM_SMD_HWKM_CLK>;
+ clock-names = "core";
+ };
+
+ rpm_msg_ram: sram@45f0000 {
+ compatible = "qcom,rpm-msg-ram";
+ reg = <0x0 0x045f0000 0x0 0x7000>;
+ };
+
+ sram@4690000 {
+ compatible = "qcom,rpm-stats";
+ reg = <0x0 0x04690000 0x0 0x10000>;
+ };
+
+ sdhc_1: mmc@4744000 {
+ compatible = "qcom,qcm2290-sdhci", "qcom,sdhci-msm-v5";
+ reg = <0x0 0x04744000 0x0 0x1000>,
+ <0x0 0x04745000 0x0 0x1000>,
+ <0x0 0x04748000 0x0 0x8000>;
+ reg-names = "hc",
+ "cqhci",
+ "ice";
+
+ interrupts = <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+ <&gcc GCC_SDCC1_APPS_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>,
+ <&gcc GCC_SDCC1_ICE_CORE_CLK>;
+ clock-names = "iface",
+ "core",
+ "xo",
+ "ice";
+
+ resets = <&gcc GCC_SDCC1_BCR>;
+
+ power-domains = <&rpmpd QCM2290_VDDCX>;
+ iommus = <&apps_smmu 0xc0 0x0>;
+
+ qcom,dll-config = <0x000f642c>;
+ qcom,ddr-config = <0x80040868>;
+ bus-width = <8>;
+
+ status = "disabled";
+ };
+
+ sdhc_2: mmc@4784000 {
+ compatible = "qcom,qcm2290-sdhci", "qcom,sdhci-msm-v5";
+ reg = <0x0 0x04784000 0x0 0x1000>;
+ reg-names = "hc";
+
+ interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+ <&gcc GCC_SDCC2_APPS_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface",
+ "core",
+ "xo";
+
+ resets = <&gcc GCC_SDCC2_BCR>;
+
+ power-domains = <&rpmpd QCM2290_VDDCX>;
+ operating-points-v2 = <&sdhc2_opp_table>;
+ iommus = <&apps_smmu 0xa0 0x0>;
+
+ qcom,dll-config = <0x0007642c>;
+ qcom,ddr-config = <0x80040868>;
+ bus-width = <4>;
+
+ status = "disabled";
+
+ sdhc2_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmpd_opp_low_svs>;
+ };
+
+ opp-202000000 {
+ opp-hz = /bits/ 64 <202000000>;
+ required-opps = <&rpmpd_opp_svs_plus>;
+ };
+ };
+ };
+
+ gpi_dma0: dma-controller@4a00000 {
+ compatible = "qcom,qcm2290-gpi-dma", "qcom,sm6350-gpi-dma";
+ reg = <0x0 0x04a00000 0x0 0x60000>;
+ interrupts = <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>;
+ dma-channels = <10>;
+ dma-channel-mask = <0x1f>;
+ iommus = <&apps_smmu 0xf6 0x0>;
+ #dma-cells = <3>;
+ status = "disabled";
+ };
+
+ qupv3_id_0: geniqup@4ac0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0x0 0x04ac0000 0x0 0x2000>;
+ clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+ clock-names = "m-ahb", "s-ahb";
+ iommus = <&apps_smmu 0xe3 0x0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ i2c0: i2c@4a80000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a80000 0x0 0x4000>;
+ interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c0_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi0: spi@4a80000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a80000 0x0 0x4000>;
+ interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi0_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 0 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart0: serial@4a80000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0x04a80000 0x0 0x4000>;
+ interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart0_default>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ i2c1: i2c@4a84000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a84000 0x0 0x4000>;
+ interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c1_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi1: spi@4a84000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a84000 0x0 0x4000>;
+ interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi1_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 1 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@4a88000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a88000 0x0 0x4000>;
+ interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c2_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi2: spi@4a88000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a88000 0x0 0x4000>;
+ interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi2_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 2 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@4a8c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a8c000 0x0 0x4000>;
+ interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c3_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 3 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi3: spi@4a8c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a8c000 0x0 0x4000>;
+ interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi3_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 3 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@4a90000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a90000 0x0 0x4000>;
+ interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c4_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 4 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi4: spi@4a90000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a90000 0x0 0x4000>;
+ interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi4_default>;
+ dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 4 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart4: serial@4a90000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0x04a90000 0x0 0x4000>;
+ interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart4_default>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ i2c5: i2c@4a94000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a94000 0x0 0x4000>;
+ interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c5_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 5 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi5: spi@4a94000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a94000 0x0 0x4000>;
+ interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi5_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 5 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+ };
+
+ usb: usb@4ef8800 {
+ compatible = "qcom,qcm2290-dwc3", "qcom,dwc3";
+ reg = <0x0 0x04ef8800 0x0 0x400>;
+ interrupts = <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hs_phy_irq", "ss_phy_irq";
+
+ clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+ <&gcc GCC_SYS_NOC_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+ <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB3_PRIM_CLKREF_CLK>;
+ clock-names = "cfg_noc",
+ "core",
+ "iface",
+ "sleep",
+ "mock_utmi",
+ "xo";
+
+ assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+ assigned-clock-rates = <19200000>, <133333333>;
+
+ resets = <&gcc GCC_USB30_PRIM_BCR>;
+ power-domains = <&gcc GCC_USB30_PRIM_GDSC>;
+ wakeup-source;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ status = "disabled";
+
+ usb_dwc3: usb@4e00000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0x04e00000 0x0 0xcd00>;
+ interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb_hsphy>;
+ phy-names = "usb2-phy";
+ iommus = <&apps_smmu 0x120 0x0>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_enblslpm_quirk;
+ snps,has-lpm-erratum;
+ snps,hird-threshold = /bits/ 8 <0x10>;
+ snps,usb3_lpm_capable;
+ maximum-speed = "super-speed";
+ dr_mode = "otg";
+ };
+ };
+
+ remoteproc_mpss: remoteproc@6080000 {
+ compatible = "qcom,qcm2290-mpss-pas", "qcom,sm6115-mpss-pas";
+ reg = <0x0 0x06080000 0x0 0x100>;
+
+ interrupts-extended = <&intc GIC_SPI 307 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog",
+ "fatal",
+ "ready",
+ "handover",
+ "stop-ack",
+ "shutdown-ack";
+
+ clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "xo";
+
+ power-domains = <&rpmpd QCM2290_VDDCX>;
+
+ memory-region = <&pil_modem_mem>;
+
+ qcom,smem-states = <&modem_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts = <GIC_SPI 68 IRQ_TYPE_EDGE_RISING>;
+ label = "mpss";
+ qcom,remote-pid = <1>;
+ mboxes = <&apcs_glb 12>;
+ };
+ };
+
+ remoteproc_adsp: remoteproc@ab00000 {
+ compatible = "qcom,qcm2290-adsp-pas", "qcom,sm6115-adsp-pas";
+ reg = <0x0 0x0ab00000 0x0 0x100>;
+
+ interrupts-extended = <&intc GIC_SPI 282 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog",
+ "fatal",
+ "ready",
+ "handover",
+ "stop-ack";
+
+ clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "xo";
+
+ power-domains = <&rpmpd QCM2290_VDD_LPI_CX>,
+ <&rpmpd QCM2290_VDD_LPI_MX>;
+
+ memory-region = <&pil_adsp_mem>;
+
+ qcom,smem-states = <&adsp_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts = <GIC_SPI 277 IRQ_TYPE_EDGE_RISING>;
+ label = "lpass";
+ qcom,remote-pid = <2>;
+ mboxes = <&apcs_glb 8>;
+ };
+ };
+
+ apps_smmu: iommu@c600000 {
+ compatible = "qcom,qcm2290-smmu-500", "qcom,smmu-500", "arm,mmu-500";
+ reg = <0x0 0x0c600000 0x0 0x80000>;
+ #iommu-cells = <2>;
+ #global-interrupts = <1>;
+
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ wifi: wifi@c800000 {
+ compatible = "qcom,wcn3990-wifi";
+ reg = <0x0 0x0c800000 0x0 0x800000>;
+ reg-names = "membase";
+ memory-region = <&wlan_msa_mem>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 362 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 364 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 366 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 367 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&apps_smmu 0x1a0 0x1>;
+ qcom,msa-fixed-perm;
+ status = "disabled";
+ };
+
+ watchdog@f017000 {
+ compatible = "qcom,apss-wdt-qcm2290", "qcom,kpss-wdt";
+ reg = <0x0 0x0f017000 0x0 0x1000>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sleep_clk>;
+ };
+
+ apcs_glb: mailbox@f111000 {
+ compatible = "qcom,qcm2290-apcs-hmss-global";
+ reg = <0x0 0x0f111000 0x0 0x1000>;
+ #mbox-cells = <1>;
+ };
+
+ timer@f120000 {
+ compatible = "arm,armv7-timer-mem";
+ reg = <0x0 0x0f120000 0x0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x0 0x0f121000 0x8000>;
+
+ frame@0 {
+ reg = <0x0 0x1000>,
+ <0x1000 0x1000>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <0>;
+ };
+
+ frame@2000 {
+ reg = <0x2000 0x1000>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <1>;
+ status = "disabled";
+ };
+
+ frame@3000 {
+ reg = <0x3000 0x1000>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <2>;
+ status = "disabled";
+ };
+
+ frame@4000 {
+ reg = <0x4000 0x1000>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <3>;
+ status = "disabled";
+ };
+
+ frame@5000 {
+ reg = <0x5000 0x1000>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <4>;
+ status = "disabled";
+ };
+
+ frame@6000 {
+ reg = <0x6000 0x1000>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <5>;
+ status = "disabled";
+ };
+
+ frame@7000 {
+ reg = <0x7000 0x1000>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <6>;
+ status = "disabled";
+ };
+ };
+
+ intc: interrupt-controller@f200000 {
+ compatible = "arm,gic-v3";
+ reg = <0x0 0x0f200000 0x0 0x10000>,
+ <0x0 0x0f300000 0x0 0x100000>;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ interrupt-parent = <&intc>;
+ #redistributor-regions = <1>;
+ redistributor-stride = <0x0 0x20000>;
+ };
+
+ cpufreq_hw: cpufreq@f521000 {
+ compatible = "qcom,qcm2290-cpufreq-hw", "qcom,cpufreq-hw";
+ reg = <0x0 0x0f521000 0x0 0x1000>;
+ reg-names = "freq-domain0";
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "dcvsh-irq-0";
+ clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, <&gcc GPLL0>;
+ clock-names = "xo", "alternate";
+
+ #freq-domain-cells = <1>;
+ #clock-cells = <1>;
+ };
+ };
+
+ thermal-zones {
+ mapss-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&tsens0 0>;
+
+ trips {
+ mapss_alert0: trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ mapss_alert1: trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ mapss_crit: mapss-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ video-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&tsens0 1>;
+
+ trips {
+ video_alert0: trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ video_alert1: trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ video_crit: video-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ wlan-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&tsens0 2>;
+
+ trips {
+ wlan_alert0: trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ wlan_alert1: trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ wlan_crit: wlan-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpuss0-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&tsens0 3>;
+
+ trips {
+ cpuss0_alert0: trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpuss0_alert1: trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpuss0_crit: cpuss0-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpuss1-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&tsens0 4>;
+
+ trips {
+ cpuss1_alert0: trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpuss1_alert1: trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpuss1_crit: cpuss1-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ mdm0-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&tsens0 5>;
+
+ trips {
+ mdm0_alert0: trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ mdm0_alert1: trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ mdm0_crit: mdm0-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ mdm1-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&tsens0 6>;
+
+ trips {
+ mdm1_alert0: trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ mdm1_alert1: trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ mdm1_crit: mdm1-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ gpu-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&tsens0 7>;
+
+ trips {
+ gpu_alert0: trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ gpu_alert1: trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ gpu_crit: gpu-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ hm-center-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&tsens0 8>;
+
+ trips {
+ hm_center_alert0: trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ hm_center_alert1: trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ hm_center_crit: hm-center-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ camera-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&tsens0 9>;
+
+ trips {
+ camera_alert0: trip-point0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ camera_alert1: trip-point1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ camera_crit: camera-crit {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
--
2.40.0
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 4/5] arm64: dts: qcom: Add initial PM2250 device tree
2023-04-05 15:50 [PATCH v2 0/5] RB1 + QCM2290 support Konrad Dybcio
` (2 preceding siblings ...)
2023-04-05 15:50 ` [PATCH v2 3/5] arm64: dts: qcom: Add initial QCM2290 device tree Konrad Dybcio
@ 2023-04-05 15:50 ` Konrad Dybcio
2023-04-05 15:50 ` [PATCH v2 5/5] arm64: dts: qcom: Add initial QTI RB1 " Konrad Dybcio
2023-04-07 18:36 ` (subset) [PATCH v2 0/5] RB1 + QCM2290 support Bjorn Andersson
5 siblings, 0 replies; 10+ messages in thread
From: Konrad Dybcio @ 2023-04-05 15:50 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Robert Marko, Das Srinagesh
Cc: Bhupesh Sharma, Vladimir Zapolskiy, Marijn Suijten,
linux-arm-msm, devicetree, linux-kernel, Konrad Dybcio
Introduce an initial device tree for the PM2250 (sometimes known as
PM4125) PMIC.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
arch/arm64/boot/dts/qcom/pm2250.dtsi | 63 ++++++++++++++++++++++++++++++++++++
1 file changed, 63 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/pm2250.dtsi b/arch/arm64/boot/dts/qcom/pm2250.dtsi
new file mode 100644
index 000000000000..5f1d15db5c99
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm2250.dtsi
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) 2023, Linaro Ltd
+ */
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+ pmic@0 {
+ compatible = "qcom,pm2250", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pon@800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x800>;
+
+ pm2250_pwrkey: pwrkey {
+ compatible = "qcom,pm8941-pwrkey";
+ interrupts-extended = <&spmi_bus 0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+ linux,code = <KEY_POWER>;
+ debounce = <15625>;
+ bias-pull-up;
+ };
+
+ pm2250_resin: resin {
+ compatible = "qcom,pm8941-resin";
+ interrupts-extended = <&spmi_bus 0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ status = "disabled";
+ };
+ };
+
+ rtc@6000 {
+ compatible = "qcom,pm8941-rtc";
+ reg = <0x6000>, <0x6100>;
+ reg-names = "rtc", "alarm";
+ interrupts-extended = <&spmi_bus 0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+ };
+
+ pm2250_gpios: gpio@c000 {
+ compatible = "qcom,pm2250-gpio", "qcom,spmi-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ gpio-ranges = <&pm2250_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmic@1 {
+ compatible = "qcom,pm2250", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
--
2.40.0
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v2 5/5] arm64: dts: qcom: Add initial QTI RB1 device tree
2023-04-05 15:50 [PATCH v2 0/5] RB1 + QCM2290 support Konrad Dybcio
` (3 preceding siblings ...)
2023-04-05 15:50 ` [PATCH v2 4/5] arm64: dts: qcom: Add initial PM2250 " Konrad Dybcio
@ 2023-04-05 15:50 ` Konrad Dybcio
2023-04-07 18:36 ` (subset) [PATCH v2 0/5] RB1 + QCM2290 support Bjorn Andersson
5 siblings, 0 replies; 10+ messages in thread
From: Konrad Dybcio @ 2023-04-05 15:50 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Robert Marko, Das Srinagesh
Cc: Bhupesh Sharma, Vladimir Zapolskiy, Marijn Suijten,
linux-arm-msm, devicetree, linux-kernel, Konrad Dybcio
Add an initial device tree for the QTI RB1 development board, based on
the QRB2210 (QCM2290 derivative) SoC. This device tree targets the SoM
revision 4, a.k.a. the Mass Production SKU.
To get a successful boot, run:
cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/qrb2210-rb1.dtb >\
.Image.gz-dtb
mkbootimg \
--kernel .Image.gz-dtb \
--ramdisk some_initrd \
--output rb1-boot.img \
--pagesize 4096 \
--base 0x8000 \
--cmdline 'some cmdline'
fastboot boot rb1-boot.img
There's no dtbo or other craziness to worry about.
For the best dev experience, you can erase boot and use fastboot boot
everytime, so that the bootloader doesn't mess with you.
If you have a SoM revision 3 or older (there should be a sticker on it
with text like -r00, where r is the revision), you will need to apply
this additional diff:
aliases {
- serial0 = &uart0;
+ serial0 = &uart4;
/* UART connected to the Micro-USB port via a FTDI chip */
- &uart0 {
+ &uart4 {
That should however only concern preproduction boards.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
arch/arm64/boot/dts/qcom/qrb2210-rb1.dts | 112 +++++++++++++++++++++++++++++++
1 file changed, 112 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts b/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts
new file mode 100644
index 000000000000..ef3616093289
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) 2023, Linaro Ltd
+ */
+
+/dts-v1/;
+
+#include "qcm2290.dtsi"
+#include "pm2250.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. Robotics RB1";
+ compatible = "qcom,qrb2210-rb1", "qcom,qrb2210", "qcom,qcm2290";
+
+ aliases {
+ serial0 = &uart0;
+ sdhc1 = &sdhc_1;
+ sdhc2 = &sdhc_2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ label = "gpio-keys";
+
+ pinctrl-0 = <&key_volp_n>;
+ pinctrl-names = "default";
+
+ key-volume-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
+ debounce-interval = <15>;
+ linux,can-disable;
+ wakeup-source;
+ };
+ };
+};
+
+&pm2250_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+ status = "okay";
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&sdhc_1 {
+ pinctrl-0 = <&sdc1_state_on>;
+ pinctrl-1 = <&sdc1_state_off>;
+ pinctrl-names = "default", "sleep";
+ non-removable;
+ supports-cqe;
+ no-sdio;
+ no-sd;
+ status = "okay";
+};
+
+&sdhc_2 {
+ cd-gpios = <&tlmm 88 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&sdc2_state_on &sd_det_in_on>;
+ pinctrl-1 = <&sdc2_state_off &sd_det_in_off>;
+ pinctrl-names = "default", "sleep";
+ no-sdio;
+ no-mmc;
+ status = "okay";
+};
+
+&tlmm {
+ sd_det_in_on: sd-det-in-on-state {
+ pins = "gpio88";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ sd_det_in_off: sd-det-in-off-state {
+ pins = "gpio88";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ key_volp_n: key-volp-n-state {
+ pins = "gpio96";
+ function = "gpio";
+ bias-pull-up;
+ output-disable;
+ };
+};
+
+/* UART connected to the Micro-USB port via a FTDI chip */
+&uart0 {
+ compatible = "qcom,geni-debug-uart";
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb_hsphy {
+ status = "okay";
+};
+
+&xo_board {
+ clock-frequency = <38400000>;
+};
--
2.40.0
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH v2 3/5] arm64: dts: qcom: Add initial QCM2290 device tree
2023-04-05 15:50 ` [PATCH v2 3/5] arm64: dts: qcom: Add initial QCM2290 device tree Konrad Dybcio
@ 2023-04-07 18:35 ` Bjorn Andersson
2023-04-07 18:47 ` Konrad Dybcio
0 siblings, 1 reply; 10+ messages in thread
From: Bjorn Andersson @ 2023-04-07 18:35 UTC (permalink / raw)
To: Konrad Dybcio
Cc: Andy Gross, Rob Herring, Krzysztof Kozlowski, Robert Marko,
Das Srinagesh, Bhupesh Sharma, Vladimir Zapolskiy,
Marijn Suijten, linux-arm-msm, devicetree, linux-kernel
On Wed, Apr 05, 2023 at 05:50:32PM +0200, Konrad Dybcio wrote:
> Add an initial device tree for the QCM2290 low-end SoC, featuring 4
> "customized" Cortex-A53 cores and up to 4 GiB of LPDDR(3/4X).
>
> This revision brings support for:
> - TSENS & thermal zones
> - SDHCI1/2
> - I2C, SPI, UART
> - MPSS
> - ADSP
> - Wi-Fi
>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/qcm2290.dtsi | 1561 +++++++++++++++++++++++++++++++++
> 2 files changed, 1562 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 1a29403400b7..6fc8d6664f0c 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -70,6 +70,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-xiaomi-sagit.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += qrb2210-rb1.dtb
I moved this to the patch that actually introduces rb1.dts
Thanks,
Bjorn
> dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5-vision-mezzanine.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qru1000-idp.dtb
> diff --git a/arch/arm64/boot/dts/qcom/qcm2290.dtsi b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
> new file mode 100644
> index 000000000000..ae5abc76bcc7
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
> @@ -0,0 +1,1561 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (c) 2023, Linaro Ltd
> + *
> + * Based on sm6115.dtsi and previous efforts by Shawn Guo & Loic Poulain.
> + */
> +
> +#include <dt-bindings/clock/qcom,gcc-qcm2290.h>
> +#include <dt-bindings/clock/qcom,rpmcc.h>
> +#include <dt-bindings/dma/qcom-gpi.h>
> +#include <dt-bindings/firmware/qcom,scm.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/power/qcom-rpmpd.h>
> +
> +/ {
> + interrupt-parent = <&intc>;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + chosen { };
> +
> + clocks {
> + xo_board: xo-board {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + };
> +
> + sleep_clk: sleep-clk {
> + compatible = "fixed-clock";
> + clock-frequency = <32764>;
> + #clock-cells = <0>;
> + };
> + };
> +
> + cpus {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + CPU0: cpu@0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x0 0x0>;
> + clocks = <&cpufreq_hw 0>;
> + capacity-dmips-mhz = <1024>;
> + dynamic-power-coefficient = <100>;
> + enable-method = "psci";
> + next-level-cache = <&L2_0>;
> + qcom,freq-domain = <&cpufreq_hw 0>;
> + L2_0: l2-cache {
> + compatible = "cache";
> + cache-level = <2>;
> + };
> + };
> +
> + CPU1: cpu@1 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x0 0x1>;
> + clocks = <&cpufreq_hw 0>;
> + capacity-dmips-mhz = <1024>;
> + dynamic-power-coefficient = <100>;
> + enable-method = "psci";
> + next-level-cache = <&L2_0>;
> + qcom,freq-domain = <&cpufreq_hw 0>;
> + };
> +
> + CPU2: cpu@2 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x0 0x2>;
> + clocks = <&cpufreq_hw 0>;
> + capacity-dmips-mhz = <1024>;
> + dynamic-power-coefficient = <100>;
> + enable-method = "psci";
> + next-level-cache = <&L2_0>;
> + qcom,freq-domain = <&cpufreq_hw 0>;
> + };
> +
> + CPU3: cpu@3 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x0 0x3>;
> + clocks = <&cpufreq_hw 0>;
> + capacity-dmips-mhz = <1024>;
> + dynamic-power-coefficient = <100>;
> + enable-method = "psci";
> + next-level-cache = <&L2_0>;
> + qcom,freq-domain = <&cpufreq_hw 0>;
> + };
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&CPU0>;
> + };
> +
> + core1 {
> + cpu = <&CPU1>;
> + };
> +
> + core2 {
> + cpu = <&CPU2>;
> + };
> +
> + core3 {
> + cpu = <&CPU3>;
> + };
> + };
> + };
> + };
> +
> + firmware {
> + scm: scm {
> + compatible = "qcom,scm-qcm2290", "qcom,scm";
> + clocks = <&rpmcc RPM_SMD_CE1_CLK>;
> + clock-names = "core";
> + #reset-cells = <1>;
> + };
> + };
> +
> + memory@40000000 {
> + device_type = "memory";
> + /* We expect the bootloader to fill in the size */
> + reg = <0 0x40000000 0 0>;
> + };
> +
> + pmu {
> + compatible = "arm,armv8-pmuv3";
> + interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + psci {
> + compatible = "arm,psci-1.0";
> + method = "smc";
> + };
> +
> + reserved_memory: reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + hyp_mem: hyp@45700000 {
> + reg = <0x0 0x45700000 0x0 0x600000>;
> + no-map;
> + };
> +
> + xbl_aop_mem: xbl-aop@45e00000 {
> + reg = <0x0 0x45e00000 0x0 0x140000>;
> + no-map;
> + };
> +
> + sec_apps_mem: sec-apps@45fff000 {
> + reg = <0x0 0x45fff000 0x0 0x1000>;
> + no-map;
> + };
> +
> + smem_mem: smem@46000000 {
> + compatible = "qcom,smem";
> + reg = <0x0 0x46000000 0x0 0x200000>;
> + no-map;
> +
> + hwlocks = <&tcsr_mutex 3>;
> + qcom,rpm-msg-ram = <&rpm_msg_ram>;
> + };
> +
> + pil_modem_mem: modem@4ab00000 {
> + reg = <0x0 0x4ab00000 0x0 0x6900000>;
> + no-map;
> + };
> +
> + pil_video_mem: video@51400000 {
> + reg = <0x0 0x51400000 0x0 0x500000>;
> + no-map;
> + };
> +
> + wlan_msa_mem: wlan-msa@51900000 {
> + reg = <0x0 0x51900000 0x0 0x100000>;
> + no-map;
> + };
> +
> + pil_adsp_mem: adsp@51a00000 {
> + reg = <0x0 0x51a00000 0x0 0x1c00000>;
> + no-map;
> + };
> +
> + pil_ipa_fw_mem: ipa-fw@53600000 {
> + reg = <0x0 0x53600000 0x0 0x10000>;
> + no-map;
> + };
> +
> + pil_ipa_gsi_mem: ipa-gsi@53610000 {
> + reg = <0x0 0x53610000 0x0 0x5000>;
> + no-map;
> + };
> +
> + pil_gpu_mem: zap@53615000 {
> + compatible = "shared-dma-pool";
> + reg = <0x0 0x53615000 0x0 0x2000>;
> + no-map;
> + };
> +
> + cont_splash_memory: framebuffer@5c000000 {
> + reg = <0x0 0x5c000000 0x0 0x00f00000>;
> + no-map;
> + };
> +
> + dfps_data_memory: dpfs-data@5cf00000 {
> + reg = <0x0 0x5cf00000 0x0 0x0100000>;
> + no-map;
> + };
> +
> + removed_mem: reserved@60000000 {
> + reg = <0x0 0x60000000 0x0 0x3900000>;
> + no-map;
> + };
> +
> + rmtfs_mem: memory@89b01000 {
> + compatible = "qcom,rmtfs-mem";
> + reg = <0x0 0x89b01000 0x0 0x200000>;
> + no-map;
> +
> + qcom,client-id = <1>;
> + qcom,vmid = <QCOM_SCM_VMID_MSS_MSA QCOM_SCM_VMID_NAV>;
> + };
> + };
> +
> + rpm-glink {
> + compatible = "qcom,glink-rpm";
> + interrupts = <GIC_SPI 194 IRQ_TYPE_EDGE_RISING>;
> + qcom,rpm-msg-ram = <&rpm_msg_ram>;
> + mboxes = <&apcs_glb 0>;
> +
> + rpm_requests: rpm-requests {
> + compatible = "qcom,rpm-qcm2290";
> + qcom,glink-channels = "rpm_requests";
> +
> + rpmcc: clock-controller {
> + compatible = "qcom,rpmcc-qcm2290", "qcom,rpmcc";
> + clocks = <&xo_board>;
> + clock-names = "xo";
> + #clock-cells = <1>;
> + };
> +
> + rpmpd: power-controller {
> + compatible = "qcom,qcm2290-rpmpd";
> + #power-domain-cells = <1>;
> + operating-points-v2 = <&rpmpd_opp_table>;
> +
> + rpmpd_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + rpmpd_opp_min_svs: opp1 {
> + opp-level = <RPM_SMD_LEVEL_MIN_SVS>;
> + };
> +
> + rpmpd_opp_low_svs: opp2 {
> + opp-level = <RPM_SMD_LEVEL_LOW_SVS>;
> + };
> +
> + rpmpd_opp_svs: opp3 {
> + opp-level = <RPM_SMD_LEVEL_SVS>;
> + };
> +
> + rpmpd_opp_svs_plus: opp4 {
> + opp-level = <RPM_SMD_LEVEL_SVS_PLUS>;
> + };
> +
> + rpmpd_opp_nom: opp5 {
> + opp-level = <RPM_SMD_LEVEL_NOM>;
> + };
> +
> + rpmpd_opp_nom_plus: opp6 {
> + opp-level = <RPM_SMD_LEVEL_NOM_PLUS>;
> + };
> +
> + rpmpd_opp_turbo: opp7 {
> + opp-level = <RPM_SMD_LEVEL_TURBO>;
> + };
> +
> + rpmpd_opp_turbo_plus: opp8 {
> + opp-level = <RPM_SMD_LEVEL_TURBO_NO_CPR>;
> + };
> + };
> + };
> + };
> + };
> +
> + smp2p-adsp {
> + compatible = "qcom,smp2p";
> + qcom,smem = <443>, <429>;
> +
> + interrupts = <GIC_SPI 279 IRQ_TYPE_EDGE_RISING>;
> +
> + mboxes = <&apcs_glb 10>;
> +
> + qcom,local-pid = <0>;
> + qcom,remote-pid = <2>;
> +
> + adsp_smp2p_out: master-kernel {
> + qcom,entry-name = "master-kernel";
> + #qcom,smem-state-cells = <1>;
> + };
> +
> + adsp_smp2p_in: slave-kernel {
> + qcom,entry-name = "slave-kernel";
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + smp2p-mpss {
> + compatible = "qcom,smp2p";
> + qcom,smem = <435>, <428>;
> +
> + interrupts = <GIC_SPI 70 IRQ_TYPE_EDGE_RISING>;
> +
> + mboxes = <&apcs_glb 14>;
> +
> + qcom,local-pid = <0>;
> + qcom,remote-pid = <1>;
> +
> + modem_smp2p_out: master-kernel {
> + qcom,entry-name = "master-kernel";
> + #qcom,smem-state-cells = <1>;
> + };
> +
> + modem_smp2p_in: slave-kernel {
> + qcom,entry-name = "slave-kernel";
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + wlan_smp2p_in: wlan-wpss-to-ap {
> + qcom,entry-name = "wlan";
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + soc: soc@0 {
> + compatible = "simple-bus";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges = <0 0 0 0 0x10 0>;
> + dma-ranges = <0 0 0 0 0x10 0>;
> +
> + tcsr_mutex: hwlock@340000 {
> + compatible = "qcom,tcsr-mutex";
> + reg = <0x0 0x00340000 0x0 0x20000>;
> + #hwlock-cells = <1>;
> + };
> +
> + tlmm: pinctrl@500000 {
> + compatible = "qcom,qcm2290-tlmm";
> + reg = <0x0 0x00500000 0x0 0x300000>;
> + interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + gpio-ranges = <&tlmm 0 0 127>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + qup_i2c0_default: qup-i2c0-default-state {
> + pins = "gpio0", "gpio1";
> + function = "qup0";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_i2c1_default: qup-i2c1-default-state {
> + pins = "gpio4", "gpio5";
> + function = "qup1";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_i2c2_default: qup-i2c2-default-state {
> + pins = "gpio6", "gpio7";
> + function = "qup2";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_i2c3_default: qup-i2c3-default-state {
> + pins = "gpio8", "gpio9";
> + function = "qup3";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_i2c4_default: qup-i2c4-default-state {
> + pins = "gpio12", "gpio13";
> + function = "qup4";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_i2c5_default: qup-i2c5-default-state {
> + pins = "gpio14", "gpio15";
> + function = "qup5";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_spi0_default: qup-spi0-default-state {
> + pins = "gpio0", "gpio1","gpio2", "gpio3";
> + function = "qup0";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_spi1_default: qup-spi1-default-state {
> + pins = "gpio4", "gpio5", "gpio69", "gpio70";
> + function = "qup1";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_spi2_default: qup-spi2-default-state {
> + pins = "gpio6", "gpio7", "gpio71", "gpio80";
> + function = "qup2";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_spi3_default: qup-spi3-default-state {
> + pins = "gpio8", "gpio9", "gpio10", "gpio11";
> + function = "qup3";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_spi4_default: qup-spi4-default-state {
> + pins = "gpio12", "gpio13", "gpio96", "gpio97";
> + function = "qup4";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_spi5_default: qup-spi5-default-state {
> + pins = "gpio14", "gpio15", "gpio16", "gpio17";
> + function = "qup5";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + qup_uart0_default: qup-uart0-default-state {
> + pins = "gpio0", "gpio1", "gpio2", "gpio3";
> + function = "qup0";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + qup_uart4_default: qup-uart4-default-state {
> + pins = "gpio12", "gpio13";
> + function = "qup4";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + sdc1_state_on: sdc1-on-state {
> + clk-pins {
> + pins = "sdc1_clk";
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + cmd-pins {
> + pins = "sdc1_cmd";
> + drive-strength = <10>;
> + bias-pull-up;
> + };
> +
> + data-pins {
> + pins = "sdc1_data";
> + drive-strength = <10>;
> + bias-pull-up;
> + };
> +
> + rclk-pins {
> + pins = "sdc1_rclk";
> + bias-pull-down;
> + };
> + };
> +
> + sdc1_state_off: sdc1-off-state {
> + clk-pins {
> + pins = "sdc1_clk";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + cmd-pins {
> + pins = "sdc1_cmd";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + data-pins {
> + pins = "sdc1_data";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + rclk-pins {
> + pins = "sdc1_rclk";
> + bias-pull-down;
> + };
> + };
> +
> + sdc2_state_on: sdc2-on-state {
> + clk-pins {
> + pins = "sdc2_clk";
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + cmd-pins {
> + pins = "sdc2_cmd";
> + drive-strength = <10>;
> + bias-pull-up;
> + };
> +
> + data-pins {
> + pins = "sdc2_data";
> + drive-strength = <10>;
> + bias-pull-up;
> + };
> + };
> +
> + sdc2_state_off: sdc2-off-state {
> + clk-pins {
> + pins = "sdc2_clk";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + cmd-pins {
> + pins = "sdc2_cmd";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + data-pins {
> + pins = "sdc2_data";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> + };
> + };
> +
> + gcc: clock-controller@1400000 {
> + compatible = "qcom,gcc-qcm2290";
> + reg = <0x0 0x01400000 0x0 0x1f0000>;
> + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, <&sleep_clk>;
> + clock-names = "bi_tcxo", "sleep_clk";
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + #power-domain-cells = <1>;
> + };
> +
> + usb_hsphy: phy@1613000 {
> + compatible = "qcom,qcm2290-qusb2-phy";
> + reg = <0x0 0x01613000 0x0 0x180>;
> +
> + clocks = <&gcc GCC_AHB2PHY_USB_CLK>,
> + <&rpmcc RPM_SMD_XO_CLK_SRC>;
> + clock-names = "cfg_ahb", "ref";
> +
> + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
> + nvmem-cells = <&qusb2_hstx_trim>;
> + #phy-cells = <0>;
> +
> + status = "disabled";
> + };
> +
> + qfprom@1b44000 {
> + compatible = "qcom,qcm2290-qfprom", "qcom,qfprom";
> + reg = <0x0 0x01b44000 0x0 0x3000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + qusb2_hstx_trim: hstx-trim@25b {
> + reg = <0x25b 0x1>;
> + bits = <1 4>;
> + };
> + };
> +
> + spmi_bus: spmi@1c40000 {
> + compatible = "qcom,spmi-pmic-arb";
> + reg = <0x0 0x01c40000 0x0 0x1100>,
> + <0x0 0x01e00000 0x0 0x2000000>,
> + <0x0 0x03e00000 0x0 0x100000>,
> + <0x0 0x03f00000 0x0 0xa0000>,
> + <0x0 0x01c0a000 0x0 0x26000>;
> + reg-names = "core",
> + "chnls",
> + "obsrvr",
> + "intr",
> + "cnfg";
> + interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "periph_irq";
> + qcom,ee = <0>;
> + qcom,channel = <0>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> + interrupt-controller;
> + #interrupt-cells = <4>;
> + };
> +
> + tsens0: thermal-sensor@4411000 {
> + compatible = "qcom,qcm2290-tsens", "qcom,tsens-v2";
> + reg = <0x0 0x04411000 0x0 0x1ff>,
> + <0x0 0x04410000 0x0 0x8>;
> + #qcom,sensors = <10>;
> + interrupts = <GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "uplow", "critical";
> + #thermal-sensor-cells = <1>;
> + };
> +
> + rng: rng@4453000 {
> + compatible = "qcom,prng-ee";
> + reg = <0x0 0x04453000 0x0 0x1000>;
> + clocks = <&rpmcc RPM_SMD_HWKM_CLK>;
> + clock-names = "core";
> + };
> +
> + rpm_msg_ram: sram@45f0000 {
> + compatible = "qcom,rpm-msg-ram";
> + reg = <0x0 0x045f0000 0x0 0x7000>;
> + };
> +
> + sram@4690000 {
> + compatible = "qcom,rpm-stats";
> + reg = <0x0 0x04690000 0x0 0x10000>;
> + };
> +
> + sdhc_1: mmc@4744000 {
> + compatible = "qcom,qcm2290-sdhci", "qcom,sdhci-msm-v5";
> + reg = <0x0 0x04744000 0x0 0x1000>,
> + <0x0 0x04745000 0x0 0x1000>,
> + <0x0 0x04748000 0x0 0x8000>;
> + reg-names = "hc",
> + "cqhci",
> + "ice";
> +
> + interrupts = <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "hc_irq", "pwr_irq";
> +
> + clocks = <&gcc GCC_SDCC1_AHB_CLK>,
> + <&gcc GCC_SDCC1_APPS_CLK>,
> + <&rpmcc RPM_SMD_XO_CLK_SRC>,
> + <&gcc GCC_SDCC1_ICE_CORE_CLK>;
> + clock-names = "iface",
> + "core",
> + "xo",
> + "ice";
> +
> + resets = <&gcc GCC_SDCC1_BCR>;
> +
> + power-domains = <&rpmpd QCM2290_VDDCX>;
> + iommus = <&apps_smmu 0xc0 0x0>;
> +
> + qcom,dll-config = <0x000f642c>;
> + qcom,ddr-config = <0x80040868>;
> + bus-width = <8>;
> +
> + status = "disabled";
> + };
> +
> + sdhc_2: mmc@4784000 {
> + compatible = "qcom,qcm2290-sdhci", "qcom,sdhci-msm-v5";
> + reg = <0x0 0x04784000 0x0 0x1000>;
> + reg-names = "hc";
> +
> + interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "hc_irq", "pwr_irq";
> +
> + clocks = <&gcc GCC_SDCC2_AHB_CLK>,
> + <&gcc GCC_SDCC2_APPS_CLK>,
> + <&rpmcc RPM_SMD_XO_CLK_SRC>;
> + clock-names = "iface",
> + "core",
> + "xo";
> +
> + resets = <&gcc GCC_SDCC2_BCR>;
> +
> + power-domains = <&rpmpd QCM2290_VDDCX>;
> + operating-points-v2 = <&sdhc2_opp_table>;
> + iommus = <&apps_smmu 0xa0 0x0>;
> +
> + qcom,dll-config = <0x0007642c>;
> + qcom,ddr-config = <0x80040868>;
> + bus-width = <4>;
> +
> + status = "disabled";
> +
> + sdhc2_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-100000000 {
> + opp-hz = /bits/ 64 <100000000>;
> + required-opps = <&rpmpd_opp_low_svs>;
> + };
> +
> + opp-202000000 {
> + opp-hz = /bits/ 64 <202000000>;
> + required-opps = <&rpmpd_opp_svs_plus>;
> + };
> + };
> + };
> +
> + gpi_dma0: dma-controller@4a00000 {
> + compatible = "qcom,qcm2290-gpi-dma", "qcom,sm6350-gpi-dma";
> + reg = <0x0 0x04a00000 0x0 0x60000>;
> + interrupts = <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>;
> + dma-channels = <10>;
> + dma-channel-mask = <0x1f>;
> + iommus = <&apps_smmu 0xf6 0x0>;
> + #dma-cells = <3>;
> + status = "disabled";
> + };
> +
> + qupv3_id_0: geniqup@4ac0000 {
> + compatible = "qcom,geni-se-qup";
> + reg = <0x0 0x04ac0000 0x0 0x2000>;
> + clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
> + <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
> + clock-names = "m-ahb", "s-ahb";
> + iommus = <&apps_smmu 0xe3 0x0>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> + status = "disabled";
> +
> + i2c0: i2c@4a80000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0x04a80000 0x0 0x4000>;
> + interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
> + clock-names = "se";
> + pinctrl-0 = <&qup_i2c0_default>;
> + pinctrl-names = "default";
> + dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
> + <&gpi_dma0 1 0 QCOM_GPI_I2C>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi0: spi@4a80000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0x04a80000 0x0 0x4000>;
> + interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
> + clock-names = "se";
> + pinctrl-0 = <&qup_spi0_default>;
> + pinctrl-names = "default";
> + dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
> + <&gpi_dma0 1 0 QCOM_GPI_SPI>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + uart0: serial@4a80000 {
> + compatible = "qcom,geni-uart";
> + reg = <0x0 0x04a80000 0x0 0x4000>;
> + interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
> + clock-names = "se";
> + pinctrl-0 = <&qup_uart0_default>;
> + pinctrl-names = "default";
> + status = "disabled";
> + };
> +
> + i2c1: i2c@4a84000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0x04a84000 0x0 0x4000>;
> + interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
> + clock-names = "se";
> + pinctrl-0 = <&qup_i2c1_default>;
> + pinctrl-names = "default";
> + dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
> + <&gpi_dma0 1 1 QCOM_GPI_I2C>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi1: spi@4a84000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0x04a84000 0x0 0x4000>;
> + interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
> + clock-names = "se";
> + pinctrl-0 = <&qup_spi1_default>;
> + pinctrl-names = "default";
> + dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
> + <&gpi_dma0 1 1 QCOM_GPI_SPI>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c2: i2c@4a88000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0x04a88000 0x0 0x4000>;
> + interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
> + clock-names = "se";
> + pinctrl-0 = <&qup_i2c2_default>;
> + pinctrl-names = "default";
> + dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
> + <&gpi_dma0 1 2 QCOM_GPI_I2C>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi2: spi@4a88000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0x04a88000 0x0 0x4000>;
> + interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
> + clock-names = "se";
> + pinctrl-0 = <&qup_spi2_default>;
> + pinctrl-names = "default";
> + dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
> + <&gpi_dma0 1 2 QCOM_GPI_SPI>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c3: i2c@4a8c000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0x04a8c000 0x0 0x4000>;
> + interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
> + clock-names = "se";
> + pinctrl-0 = <&qup_i2c3_default>;
> + pinctrl-names = "default";
> + dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
> + <&gpi_dma0 1 3 QCOM_GPI_I2C>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi3: spi@4a8c000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0x04a8c000 0x0 0x4000>;
> + interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
> + clock-names = "se";
> + pinctrl-0 = <&qup_spi3_default>;
> + pinctrl-names = "default";
> + dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
> + <&gpi_dma0 1 3 QCOM_GPI_SPI>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c4: i2c@4a90000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0x04a90000 0x0 0x4000>;
> + interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
> + clock-names = "se";
> + pinctrl-0 = <&qup_i2c4_default>;
> + pinctrl-names = "default";
> + dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
> + <&gpi_dma0 1 4 QCOM_GPI_I2C>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi4: spi@4a90000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0x04a90000 0x0 0x4000>;
> + interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi4_default>;
> + dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
> + <&gpi_dma0 1 4 QCOM_GPI_SPI>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + uart4: serial@4a90000 {
> + compatible = "qcom,geni-uart";
> + reg = <0x0 0x04a90000 0x0 0x4000>;
> + interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
> + clock-names = "se";
> + pinctrl-0 = <&qup_uart4_default>;
> + pinctrl-names = "default";
> + status = "disabled";
> + };
> +
> + i2c5: i2c@4a94000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0x04a94000 0x0 0x4000>;
> + interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
> + clock-names = "se";
> + pinctrl-0 = <&qup_i2c5_default>;
> + pinctrl-names = "default";
> + dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
> + <&gpi_dma0 1 5 QCOM_GPI_I2C>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi5: spi@4a94000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0x04a94000 0x0 0x4000>;
> + interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
> + clock-names = "se";
> + pinctrl-0 = <&qup_spi5_default>;
> + pinctrl-names = "default";
> + dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
> + <&gpi_dma0 1 5 QCOM_GPI_SPI>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> + };
> +
> + usb: usb@4ef8800 {
> + compatible = "qcom,qcm2290-dwc3", "qcom,dwc3";
> + reg = <0x0 0x04ef8800 0x0 0x400>;
> + interrupts = <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "hs_phy_irq", "ss_phy_irq";
> +
> + clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
> + <&gcc GCC_USB30_PRIM_MASTER_CLK>,
> + <&gcc GCC_SYS_NOC_USB3_PRIM_AXI_CLK>,
> + <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
> + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
> + <&gcc GCC_USB3_PRIM_CLKREF_CLK>;
> + clock-names = "cfg_noc",
> + "core",
> + "iface",
> + "sleep",
> + "mock_utmi",
> + "xo";
> +
> + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
> + <&gcc GCC_USB30_PRIM_MASTER_CLK>;
> + assigned-clock-rates = <19200000>, <133333333>;
> +
> + resets = <&gcc GCC_USB30_PRIM_BCR>;
> + power-domains = <&gcc GCC_USB30_PRIM_GDSC>;
> + wakeup-source;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + status = "disabled";
> +
> + usb_dwc3: usb@4e00000 {
> + compatible = "snps,dwc3";
> + reg = <0x0 0x04e00000 0x0 0xcd00>;
> + interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
> + phys = <&usb_hsphy>;
> + phy-names = "usb2-phy";
> + iommus = <&apps_smmu 0x120 0x0>;
> + snps,dis_u2_susphy_quirk;
> + snps,dis_enblslpm_quirk;
> + snps,has-lpm-erratum;
> + snps,hird-threshold = /bits/ 8 <0x10>;
> + snps,usb3_lpm_capable;
> + maximum-speed = "super-speed";
> + dr_mode = "otg";
> + };
> + };
> +
> + remoteproc_mpss: remoteproc@6080000 {
> + compatible = "qcom,qcm2290-mpss-pas", "qcom,sm6115-mpss-pas";
> + reg = <0x0 0x06080000 0x0 0x100>;
> +
> + interrupts-extended = <&intc GIC_SPI 307 IRQ_TYPE_EDGE_RISING>,
> + <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> + <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> + <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> + <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
> + <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "wdog",
> + "fatal",
> + "ready",
> + "handover",
> + "stop-ack",
> + "shutdown-ack";
> +
> + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
> + clock-names = "xo";
> +
> + power-domains = <&rpmpd QCM2290_VDDCX>;
> +
> + memory-region = <&pil_modem_mem>;
> +
> + qcom,smem-states = <&modem_smp2p_out 0>;
> + qcom,smem-state-names = "stop";
> +
> + status = "disabled";
> +
> + glink-edge {
> + interrupts = <GIC_SPI 68 IRQ_TYPE_EDGE_RISING>;
> + label = "mpss";
> + qcom,remote-pid = <1>;
> + mboxes = <&apcs_glb 12>;
> + };
> + };
> +
> + remoteproc_adsp: remoteproc@ab00000 {
> + compatible = "qcom,qcm2290-adsp-pas", "qcom,sm6115-adsp-pas";
> + reg = <0x0 0x0ab00000 0x0 0x100>;
> +
> + interrupts-extended = <&intc GIC_SPI 282 IRQ_TYPE_EDGE_RISING>,
> + <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> + <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> + <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> + <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "wdog",
> + "fatal",
> + "ready",
> + "handover",
> + "stop-ack";
> +
> + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
> + clock-names = "xo";
> +
> + power-domains = <&rpmpd QCM2290_VDD_LPI_CX>,
> + <&rpmpd QCM2290_VDD_LPI_MX>;
> +
> + memory-region = <&pil_adsp_mem>;
> +
> + qcom,smem-states = <&adsp_smp2p_out 0>;
> + qcom,smem-state-names = "stop";
> +
> + status = "disabled";
> +
> + glink-edge {
> + interrupts = <GIC_SPI 277 IRQ_TYPE_EDGE_RISING>;
> + label = "lpass";
> + qcom,remote-pid = <2>;
> + mboxes = <&apcs_glb 8>;
> + };
> + };
> +
> + apps_smmu: iommu@c600000 {
> + compatible = "qcom,qcm2290-smmu-500", "qcom,smmu-500", "arm,mmu-500";
> + reg = <0x0 0x0c600000 0x0 0x80000>;
> + #iommu-cells = <2>;
> + #global-interrupts = <1>;
> +
> + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + wifi: wifi@c800000 {
> + compatible = "qcom,wcn3990-wifi";
> + reg = <0x0 0x0c800000 0x0 0x800000>;
> + reg-names = "membase";
> + memory-region = <&wlan_msa_mem>;
> + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 362 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 364 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 366 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 367 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
> + iommus = <&apps_smmu 0x1a0 0x1>;
> + qcom,msa-fixed-perm;
> + status = "disabled";
> + };
> +
> + watchdog@f017000 {
> + compatible = "qcom,apss-wdt-qcm2290", "qcom,kpss-wdt";
> + reg = <0x0 0x0f017000 0x0 0x1000>;
> + interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&sleep_clk>;
> + };
> +
> + apcs_glb: mailbox@f111000 {
> + compatible = "qcom,qcm2290-apcs-hmss-global";
> + reg = <0x0 0x0f111000 0x0 0x1000>;
> + #mbox-cells = <1>;
> + };
> +
> + timer@f120000 {
> + compatible = "arm,armv7-timer-mem";
> + reg = <0x0 0x0f120000 0x0 0x1000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0x0 0x0f121000 0x8000>;
> +
> + frame@0 {
> + reg = <0x0 0x1000>,
> + <0x1000 0x1000>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> + frame-number = <0>;
> + };
> +
> + frame@2000 {
> + reg = <0x2000 0x1000>;
> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> + frame-number = <1>;
> + status = "disabled";
> + };
> +
> + frame@3000 {
> + reg = <0x3000 0x1000>;
> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> + frame-number = <2>;
> + status = "disabled";
> + };
> +
> + frame@4000 {
> + reg = <0x4000 0x1000>;
> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> + frame-number = <3>;
> + status = "disabled";
> + };
> +
> + frame@5000 {
> + reg = <0x5000 0x1000>;
> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> + frame-number = <4>;
> + status = "disabled";
> + };
> +
> + frame@6000 {
> + reg = <0x6000 0x1000>;
> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> + frame-number = <5>;
> + status = "disabled";
> + };
> +
> + frame@7000 {
> + reg = <0x7000 0x1000>;
> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> + frame-number = <6>;
> + status = "disabled";
> + };
> + };
> +
> + intc: interrupt-controller@f200000 {
> + compatible = "arm,gic-v3";
> + reg = <0x0 0x0f200000 0x0 0x10000>,
> + <0x0 0x0f300000 0x0 0x100000>;
> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
> + #interrupt-cells = <3>;
> + interrupt-controller;
> + interrupt-parent = <&intc>;
> + #redistributor-regions = <1>;
> + redistributor-stride = <0x0 0x20000>;
> + };
> +
> + cpufreq_hw: cpufreq@f521000 {
> + compatible = "qcom,qcm2290-cpufreq-hw", "qcom,cpufreq-hw";
> + reg = <0x0 0x0f521000 0x0 0x1000>;
> + reg-names = "freq-domain0";
> + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "dcvsh-irq-0";
> + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, <&gcc GPLL0>;
> + clock-names = "xo", "alternate";
> +
> + #freq-domain-cells = <1>;
> + #clock-cells = <1>;
> + };
> + };
> +
> + thermal-zones {
> + mapss-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&tsens0 0>;
> +
> + trips {
> + mapss_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + mapss_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + mapss_crit: mapss-crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + video-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&tsens0 1>;
> +
> + trips {
> + video_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + video_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + video_crit: video-crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + wlan-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&tsens0 2>;
> +
> + trips {
> + wlan_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + wlan_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + wlan_crit: wlan-crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + cpuss0-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&tsens0 3>;
> +
> + trips {
> + cpuss0_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpuss0_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpuss0_crit: cpuss0-crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + cpuss1-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&tsens0 4>;
> +
> + trips {
> + cpuss1_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpuss1_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpuss1_crit: cpuss1-crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + mdm0-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&tsens0 5>;
> +
> + trips {
> + mdm0_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + mdm0_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + mdm0_crit: mdm0-crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + mdm1-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&tsens0 6>;
> +
> + trips {
> + mdm1_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + mdm1_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + mdm1_crit: mdm1-crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + gpu-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&tsens0 7>;
> +
> + trips {
> + gpu_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + gpu_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + gpu_crit: gpu-crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + hm-center-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&tsens0 8>;
> +
> + trips {
> + hm_center_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + hm_center_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + hm_center_crit: hm-center-crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + camera-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&tsens0 9>;
> +
> + trips {
> + camera_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + camera_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + camera_crit: camera-crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +};
>
> --
> 2.40.0
>
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: (subset) [PATCH v2 0/5] RB1 + QCM2290 support
2023-04-05 15:50 [PATCH v2 0/5] RB1 + QCM2290 support Konrad Dybcio
` (4 preceding siblings ...)
2023-04-05 15:50 ` [PATCH v2 5/5] arm64: dts: qcom: Add initial QTI RB1 " Konrad Dybcio
@ 2023-04-07 18:36 ` Bjorn Andersson
5 siblings, 0 replies; 10+ messages in thread
From: Bjorn Andersson @ 2023-04-07 18:36 UTC (permalink / raw)
To: Das Srinagesh, Robert Marko, Andy Gross, Rob Herring,
Krzysztof Kozlowski, Konrad Dybcio
Cc: Bhupesh Sharma, devicetree, Krzysztof Kozlowski, linux-kernel,
Marijn Suijten, linux-arm-msm, Vladimir Zapolskiy
On Wed, 05 Apr 2023 17:50:29 +0200, Konrad Dybcio wrote:
> v1 -> v2:
> - Fix missing newline in pm2250.dtsi
> - Use an enum in [2/5] to allow for more QRB2210 boards
> - Squash the dt patches into one per SoC, PMIC and board
> - pick up rb on [1/5]
>
> v1: https://lore.kernel.org/r/20230403-topic-rb1_qcm-v1-0-ca849b62ba07@linaro.org
>
> [...]
Applied, thanks!
[3/5] arm64: dts: qcom: Add initial QCM2290 device tree
commit: a64a0192b70cfe7537072ae61a5e0d1d99f976bc
[4/5] arm64: dts: qcom: Add initial PM2250 device tree
commit: c309b9a54039053892cc5417193e9f0089073ae3
[5/5] arm64: dts: qcom: Add initial QTI RB1 device tree
commit: e18771961336647121c40cad4585caa794980887
Best regards,
--
Bjorn Andersson <andersson@kernel.org>
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v2 3/5] arm64: dts: qcom: Add initial QCM2290 device tree
2023-04-07 18:35 ` Bjorn Andersson
@ 2023-04-07 18:47 ` Konrad Dybcio
0 siblings, 0 replies; 10+ messages in thread
From: Konrad Dybcio @ 2023-04-07 18:47 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Andy Gross, Rob Herring, Krzysztof Kozlowski, Robert Marko,
Das Srinagesh, Bhupesh Sharma, Vladimir Zapolskiy,
Marijn Suijten, linux-arm-msm, devicetree, linux-kernel
On 7.04.2023 20:35, Bjorn Andersson wrote:
> On Wed, Apr 05, 2023 at 05:50:32PM +0200, Konrad Dybcio wrote:
>> Add an initial device tree for the QCM2290 low-end SoC, featuring 4
>> "customized" Cortex-A53 cores and up to 4 GiB of LPDDR(3/4X).
>>
>> This revision brings support for:
>> - TSENS & thermal zones
>> - SDHCI1/2
>> - I2C, SPI, UART
>> - MPSS
>> - ADSP
>> - Wi-Fi
>>
>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>> ---
>> arch/arm64/boot/dts/qcom/Makefile | 1 +
>> arch/arm64/boot/dts/qcom/qcm2290.dtsi | 1561 +++++++++++++++++++++++++++++++++
>> 2 files changed, 1562 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>> index 1a29403400b7..6fc8d6664f0c 100644
>> --- a/arch/arm64/boot/dts/qcom/Makefile
>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>> @@ -70,6 +70,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-xiaomi-sagit.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
>> +dtb-$(CONFIG_ARCH_QCOM) += qrb2210-rb1.dtb
>
> I moved this to the patch that actually introduces rb1.dts
Thanks for spotting this!
Konrad
>
> Thanks,
> Bjorn
>
>> dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5-vision-mezzanine.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qru1000-idp.dtb
>> diff --git a/arch/arm64/boot/dts/qcom/qcm2290.dtsi b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
>> new file mode 100644
>> index 000000000000..ae5abc76bcc7
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
>> @@ -0,0 +1,1561 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
>> +/*
>> + * Copyright (c) 2023, Linaro Ltd
>> + *
>> + * Based on sm6115.dtsi and previous efforts by Shawn Guo & Loic Poulain.
>> + */
>> +
>> +#include <dt-bindings/clock/qcom,gcc-qcm2290.h>
>> +#include <dt-bindings/clock/qcom,rpmcc.h>
>> +#include <dt-bindings/dma/qcom-gpi.h>
>> +#include <dt-bindings/firmware/qcom,scm.h>
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/power/qcom-rpmpd.h>
>> +
>> +/ {
>> + interrupt-parent = <&intc>;
>> +
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> +
>> + chosen { };
>> +
>> + clocks {
>> + xo_board: xo-board {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + };
>> +
>> + sleep_clk: sleep-clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <32764>;
>> + #clock-cells = <0>;
>> + };
>> + };
>> +
>> + cpus {
>> + #address-cells = <2>;
>> + #size-cells = <0>;
>> +
>> + CPU0: cpu@0 {
>> + device_type = "cpu";
>> + compatible = "arm,cortex-a53";
>> + reg = <0x0 0x0>;
>> + clocks = <&cpufreq_hw 0>;
>> + capacity-dmips-mhz = <1024>;
>> + dynamic-power-coefficient = <100>;
>> + enable-method = "psci";
>> + next-level-cache = <&L2_0>;
>> + qcom,freq-domain = <&cpufreq_hw 0>;
>> + L2_0: l2-cache {
>> + compatible = "cache";
>> + cache-level = <2>;
>> + };
>> + };
>> +
>> + CPU1: cpu@1 {
>> + device_type = "cpu";
>> + compatible = "arm,cortex-a53";
>> + reg = <0x0 0x1>;
>> + clocks = <&cpufreq_hw 0>;
>> + capacity-dmips-mhz = <1024>;
>> + dynamic-power-coefficient = <100>;
>> + enable-method = "psci";
>> + next-level-cache = <&L2_0>;
>> + qcom,freq-domain = <&cpufreq_hw 0>;
>> + };
>> +
>> + CPU2: cpu@2 {
>> + device_type = "cpu";
>> + compatible = "arm,cortex-a53";
>> + reg = <0x0 0x2>;
>> + clocks = <&cpufreq_hw 0>;
>> + capacity-dmips-mhz = <1024>;
>> + dynamic-power-coefficient = <100>;
>> + enable-method = "psci";
>> + next-level-cache = <&L2_0>;
>> + qcom,freq-domain = <&cpufreq_hw 0>;
>> + };
>> +
>> + CPU3: cpu@3 {
>> + device_type = "cpu";
>> + compatible = "arm,cortex-a53";
>> + reg = <0x0 0x3>;
>> + clocks = <&cpufreq_hw 0>;
>> + capacity-dmips-mhz = <1024>;
>> + dynamic-power-coefficient = <100>;
>> + enable-method = "psci";
>> + next-level-cache = <&L2_0>;
>> + qcom,freq-domain = <&cpufreq_hw 0>;
>> + };
>> +
>> + cpu-map {
>> + cluster0 {
>> + core0 {
>> + cpu = <&CPU0>;
>> + };
>> +
>> + core1 {
>> + cpu = <&CPU1>;
>> + };
>> +
>> + core2 {
>> + cpu = <&CPU2>;
>> + };
>> +
>> + core3 {
>> + cpu = <&CPU3>;
>> + };
>> + };
>> + };
>> + };
>> +
>> + firmware {
>> + scm: scm {
>> + compatible = "qcom,scm-qcm2290", "qcom,scm";
>> + clocks = <&rpmcc RPM_SMD_CE1_CLK>;
>> + clock-names = "core";
>> + #reset-cells = <1>;
>> + };
>> + };
>> +
>> + memory@40000000 {
>> + device_type = "memory";
>> + /* We expect the bootloader to fill in the size */
>> + reg = <0 0x40000000 0 0>;
>> + };
>> +
>> + pmu {
>> + compatible = "arm,armv8-pmuv3";
>> + interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>;
>> + };
>> +
>> + psci {
>> + compatible = "arm,psci-1.0";
>> + method = "smc";
>> + };
>> +
>> + reserved_memory: reserved-memory {
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> + ranges;
>> +
>> + hyp_mem: hyp@45700000 {
>> + reg = <0x0 0x45700000 0x0 0x600000>;
>> + no-map;
>> + };
>> +
>> + xbl_aop_mem: xbl-aop@45e00000 {
>> + reg = <0x0 0x45e00000 0x0 0x140000>;
>> + no-map;
>> + };
>> +
>> + sec_apps_mem: sec-apps@45fff000 {
>> + reg = <0x0 0x45fff000 0x0 0x1000>;
>> + no-map;
>> + };
>> +
>> + smem_mem: smem@46000000 {
>> + compatible = "qcom,smem";
>> + reg = <0x0 0x46000000 0x0 0x200000>;
>> + no-map;
>> +
>> + hwlocks = <&tcsr_mutex 3>;
>> + qcom,rpm-msg-ram = <&rpm_msg_ram>;
>> + };
>> +
>> + pil_modem_mem: modem@4ab00000 {
>> + reg = <0x0 0x4ab00000 0x0 0x6900000>;
>> + no-map;
>> + };
>> +
>> + pil_video_mem: video@51400000 {
>> + reg = <0x0 0x51400000 0x0 0x500000>;
>> + no-map;
>> + };
>> +
>> + wlan_msa_mem: wlan-msa@51900000 {
>> + reg = <0x0 0x51900000 0x0 0x100000>;
>> + no-map;
>> + };
>> +
>> + pil_adsp_mem: adsp@51a00000 {
>> + reg = <0x0 0x51a00000 0x0 0x1c00000>;
>> + no-map;
>> + };
>> +
>> + pil_ipa_fw_mem: ipa-fw@53600000 {
>> + reg = <0x0 0x53600000 0x0 0x10000>;
>> + no-map;
>> + };
>> +
>> + pil_ipa_gsi_mem: ipa-gsi@53610000 {
>> + reg = <0x0 0x53610000 0x0 0x5000>;
>> + no-map;
>> + };
>> +
>> + pil_gpu_mem: zap@53615000 {
>> + compatible = "shared-dma-pool";
>> + reg = <0x0 0x53615000 0x0 0x2000>;
>> + no-map;
>> + };
>> +
>> + cont_splash_memory: framebuffer@5c000000 {
>> + reg = <0x0 0x5c000000 0x0 0x00f00000>;
>> + no-map;
>> + };
>> +
>> + dfps_data_memory: dpfs-data@5cf00000 {
>> + reg = <0x0 0x5cf00000 0x0 0x0100000>;
>> + no-map;
>> + };
>> +
>> + removed_mem: reserved@60000000 {
>> + reg = <0x0 0x60000000 0x0 0x3900000>;
>> + no-map;
>> + };
>> +
>> + rmtfs_mem: memory@89b01000 {
>> + compatible = "qcom,rmtfs-mem";
>> + reg = <0x0 0x89b01000 0x0 0x200000>;
>> + no-map;
>> +
>> + qcom,client-id = <1>;
>> + qcom,vmid = <QCOM_SCM_VMID_MSS_MSA QCOM_SCM_VMID_NAV>;
>> + };
>> + };
>> +
>> + rpm-glink {
>> + compatible = "qcom,glink-rpm";
>> + interrupts = <GIC_SPI 194 IRQ_TYPE_EDGE_RISING>;
>> + qcom,rpm-msg-ram = <&rpm_msg_ram>;
>> + mboxes = <&apcs_glb 0>;
>> +
>> + rpm_requests: rpm-requests {
>> + compatible = "qcom,rpm-qcm2290";
>> + qcom,glink-channels = "rpm_requests";
>> +
>> + rpmcc: clock-controller {
>> + compatible = "qcom,rpmcc-qcm2290", "qcom,rpmcc";
>> + clocks = <&xo_board>;
>> + clock-names = "xo";
>> + #clock-cells = <1>;
>> + };
>> +
>> + rpmpd: power-controller {
>> + compatible = "qcom,qcm2290-rpmpd";
>> + #power-domain-cells = <1>;
>> + operating-points-v2 = <&rpmpd_opp_table>;
>> +
>> + rpmpd_opp_table: opp-table {
>> + compatible = "operating-points-v2";
>> +
>> + rpmpd_opp_min_svs: opp1 {
>> + opp-level = <RPM_SMD_LEVEL_MIN_SVS>;
>> + };
>> +
>> + rpmpd_opp_low_svs: opp2 {
>> + opp-level = <RPM_SMD_LEVEL_LOW_SVS>;
>> + };
>> +
>> + rpmpd_opp_svs: opp3 {
>> + opp-level = <RPM_SMD_LEVEL_SVS>;
>> + };
>> +
>> + rpmpd_opp_svs_plus: opp4 {
>> + opp-level = <RPM_SMD_LEVEL_SVS_PLUS>;
>> + };
>> +
>> + rpmpd_opp_nom: opp5 {
>> + opp-level = <RPM_SMD_LEVEL_NOM>;
>> + };
>> +
>> + rpmpd_opp_nom_plus: opp6 {
>> + opp-level = <RPM_SMD_LEVEL_NOM_PLUS>;
>> + };
>> +
>> + rpmpd_opp_turbo: opp7 {
>> + opp-level = <RPM_SMD_LEVEL_TURBO>;
>> + };
>> +
>> + rpmpd_opp_turbo_plus: opp8 {
>> + opp-level = <RPM_SMD_LEVEL_TURBO_NO_CPR>;
>> + };
>> + };
>> + };
>> + };
>> + };
>> +
>> + smp2p-adsp {
>> + compatible = "qcom,smp2p";
>> + qcom,smem = <443>, <429>;
>> +
>> + interrupts = <GIC_SPI 279 IRQ_TYPE_EDGE_RISING>;
>> +
>> + mboxes = <&apcs_glb 10>;
>> +
>> + qcom,local-pid = <0>;
>> + qcom,remote-pid = <2>;
>> +
>> + adsp_smp2p_out: master-kernel {
>> + qcom,entry-name = "master-kernel";
>> + #qcom,smem-state-cells = <1>;
>> + };
>> +
>> + adsp_smp2p_in: slave-kernel {
>> + qcom,entry-name = "slave-kernel";
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + };
>> + };
>> +
>> + smp2p-mpss {
>> + compatible = "qcom,smp2p";
>> + qcom,smem = <435>, <428>;
>> +
>> + interrupts = <GIC_SPI 70 IRQ_TYPE_EDGE_RISING>;
>> +
>> + mboxes = <&apcs_glb 14>;
>> +
>> + qcom,local-pid = <0>;
>> + qcom,remote-pid = <1>;
>> +
>> + modem_smp2p_out: master-kernel {
>> + qcom,entry-name = "master-kernel";
>> + #qcom,smem-state-cells = <1>;
>> + };
>> +
>> + modem_smp2p_in: slave-kernel {
>> + qcom,entry-name = "slave-kernel";
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + };
>> +
>> + wlan_smp2p_in: wlan-wpss-to-ap {
>> + qcom,entry-name = "wlan";
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + };
>> + };
>> +
>> + soc: soc@0 {
>> + compatible = "simple-bus";
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> + ranges = <0 0 0 0 0x10 0>;
>> + dma-ranges = <0 0 0 0 0x10 0>;
>> +
>> + tcsr_mutex: hwlock@340000 {
>> + compatible = "qcom,tcsr-mutex";
>> + reg = <0x0 0x00340000 0x0 0x20000>;
>> + #hwlock-cells = <1>;
>> + };
>> +
>> + tlmm: pinctrl@500000 {
>> + compatible = "qcom,qcm2290-tlmm";
>> + reg = <0x0 0x00500000 0x0 0x300000>;
>> + interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
>> + gpio-controller;
>> + gpio-ranges = <&tlmm 0 0 127>;
>> + #gpio-cells = <2>;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> +
>> + qup_i2c0_default: qup-i2c0-default-state {
>> + pins = "gpio0", "gpio1";
>> + function = "qup0";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> +
>> + qup_i2c1_default: qup-i2c1-default-state {
>> + pins = "gpio4", "gpio5";
>> + function = "qup1";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> +
>> + qup_i2c2_default: qup-i2c2-default-state {
>> + pins = "gpio6", "gpio7";
>> + function = "qup2";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> +
>> + qup_i2c3_default: qup-i2c3-default-state {
>> + pins = "gpio8", "gpio9";
>> + function = "qup3";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> +
>> + qup_i2c4_default: qup-i2c4-default-state {
>> + pins = "gpio12", "gpio13";
>> + function = "qup4";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> +
>> + qup_i2c5_default: qup-i2c5-default-state {
>> + pins = "gpio14", "gpio15";
>> + function = "qup5";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> +
>> + qup_spi0_default: qup-spi0-default-state {
>> + pins = "gpio0", "gpio1","gpio2", "gpio3";
>> + function = "qup0";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> +
>> + qup_spi1_default: qup-spi1-default-state {
>> + pins = "gpio4", "gpio5", "gpio69", "gpio70";
>> + function = "qup1";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> +
>> + qup_spi2_default: qup-spi2-default-state {
>> + pins = "gpio6", "gpio7", "gpio71", "gpio80";
>> + function = "qup2";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> +
>> + qup_spi3_default: qup-spi3-default-state {
>> + pins = "gpio8", "gpio9", "gpio10", "gpio11";
>> + function = "qup3";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> +
>> + qup_spi4_default: qup-spi4-default-state {
>> + pins = "gpio12", "gpio13", "gpio96", "gpio97";
>> + function = "qup4";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> +
>> + qup_spi5_default: qup-spi5-default-state {
>> + pins = "gpio14", "gpio15", "gpio16", "gpio17";
>> + function = "qup5";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> +
>> + qup_uart0_default: qup-uart0-default-state {
>> + pins = "gpio0", "gpio1", "gpio2", "gpio3";
>> + function = "qup0";
>> + drive-strength = <2>;
>> + bias-disable;
>> + };
>> +
>> + qup_uart4_default: qup-uart4-default-state {
>> + pins = "gpio12", "gpio13";
>> + function = "qup4";
>> + drive-strength = <2>;
>> + bias-disable;
>> + };
>> +
>> + sdc1_state_on: sdc1-on-state {
>> + clk-pins {
>> + pins = "sdc1_clk";
>> + drive-strength = <16>;
>> + bias-disable;
>> + };
>> +
>> + cmd-pins {
>> + pins = "sdc1_cmd";
>> + drive-strength = <10>;
>> + bias-pull-up;
>> + };
>> +
>> + data-pins {
>> + pins = "sdc1_data";
>> + drive-strength = <10>;
>> + bias-pull-up;
>> + };
>> +
>> + rclk-pins {
>> + pins = "sdc1_rclk";
>> + bias-pull-down;
>> + };
>> + };
>> +
>> + sdc1_state_off: sdc1-off-state {
>> + clk-pins {
>> + pins = "sdc1_clk";
>> + drive-strength = <2>;
>> + bias-disable;
>> + };
>> +
>> + cmd-pins {
>> + pins = "sdc1_cmd";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> +
>> + data-pins {
>> + pins = "sdc1_data";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> +
>> + rclk-pins {
>> + pins = "sdc1_rclk";
>> + bias-pull-down;
>> + };
>> + };
>> +
>> + sdc2_state_on: sdc2-on-state {
>> + clk-pins {
>> + pins = "sdc2_clk";
>> + drive-strength = <16>;
>> + bias-disable;
>> + };
>> +
>> + cmd-pins {
>> + pins = "sdc2_cmd";
>> + drive-strength = <10>;
>> + bias-pull-up;
>> + };
>> +
>> + data-pins {
>> + pins = "sdc2_data";
>> + drive-strength = <10>;
>> + bias-pull-up;
>> + };
>> + };
>> +
>> + sdc2_state_off: sdc2-off-state {
>> + clk-pins {
>> + pins = "sdc2_clk";
>> + drive-strength = <2>;
>> + bias-disable;
>> + };
>> +
>> + cmd-pins {
>> + pins = "sdc2_cmd";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> +
>> + data-pins {
>> + pins = "sdc2_data";
>> + drive-strength = <2>;
>> + bias-pull-up;
>> + };
>> + };
>> + };
>> +
>> + gcc: clock-controller@1400000 {
>> + compatible = "qcom,gcc-qcm2290";
>> + reg = <0x0 0x01400000 0x0 0x1f0000>;
>> + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, <&sleep_clk>;
>> + clock-names = "bi_tcxo", "sleep_clk";
>> + #clock-cells = <1>;
>> + #reset-cells = <1>;
>> + #power-domain-cells = <1>;
>> + };
>> +
>> + usb_hsphy: phy@1613000 {
>> + compatible = "qcom,qcm2290-qusb2-phy";
>> + reg = <0x0 0x01613000 0x0 0x180>;
>> +
>> + clocks = <&gcc GCC_AHB2PHY_USB_CLK>,
>> + <&rpmcc RPM_SMD_XO_CLK_SRC>;
>> + clock-names = "cfg_ahb", "ref";
>> +
>> + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
>> + nvmem-cells = <&qusb2_hstx_trim>;
>> + #phy-cells = <0>;
>> +
>> + status = "disabled";
>> + };
>> +
>> + qfprom@1b44000 {
>> + compatible = "qcom,qcm2290-qfprom", "qcom,qfprom";
>> + reg = <0x0 0x01b44000 0x0 0x3000>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> +
>> + qusb2_hstx_trim: hstx-trim@25b {
>> + reg = <0x25b 0x1>;
>> + bits = <1 4>;
>> + };
>> + };
>> +
>> + spmi_bus: spmi@1c40000 {
>> + compatible = "qcom,spmi-pmic-arb";
>> + reg = <0x0 0x01c40000 0x0 0x1100>,
>> + <0x0 0x01e00000 0x0 0x2000000>,
>> + <0x0 0x03e00000 0x0 0x100000>,
>> + <0x0 0x03f00000 0x0 0xa0000>,
>> + <0x0 0x01c0a000 0x0 0x26000>;
>> + reg-names = "core",
>> + "chnls",
>> + "obsrvr",
>> + "intr",
>> + "cnfg";
>> + interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "periph_irq";
>> + qcom,ee = <0>;
>> + qcom,channel = <0>;
>> + #address-cells = <2>;
>> + #size-cells = <0>;
>> + interrupt-controller;
>> + #interrupt-cells = <4>;
>> + };
>> +
>> + tsens0: thermal-sensor@4411000 {
>> + compatible = "qcom,qcm2290-tsens", "qcom,tsens-v2";
>> + reg = <0x0 0x04411000 0x0 0x1ff>,
>> + <0x0 0x04410000 0x0 0x8>;
>> + #qcom,sensors = <10>;
>> + interrupts = <GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "uplow", "critical";
>> + #thermal-sensor-cells = <1>;
>> + };
>> +
>> + rng: rng@4453000 {
>> + compatible = "qcom,prng-ee";
>> + reg = <0x0 0x04453000 0x0 0x1000>;
>> + clocks = <&rpmcc RPM_SMD_HWKM_CLK>;
>> + clock-names = "core";
>> + };
>> +
>> + rpm_msg_ram: sram@45f0000 {
>> + compatible = "qcom,rpm-msg-ram";
>> + reg = <0x0 0x045f0000 0x0 0x7000>;
>> + };
>> +
>> + sram@4690000 {
>> + compatible = "qcom,rpm-stats";
>> + reg = <0x0 0x04690000 0x0 0x10000>;
>> + };
>> +
>> + sdhc_1: mmc@4744000 {
>> + compatible = "qcom,qcm2290-sdhci", "qcom,sdhci-msm-v5";
>> + reg = <0x0 0x04744000 0x0 0x1000>,
>> + <0x0 0x04745000 0x0 0x1000>,
>> + <0x0 0x04748000 0x0 0x8000>;
>> + reg-names = "hc",
>> + "cqhci",
>> + "ice";
>> +
>> + interrupts = <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "hc_irq", "pwr_irq";
>> +
>> + clocks = <&gcc GCC_SDCC1_AHB_CLK>,
>> + <&gcc GCC_SDCC1_APPS_CLK>,
>> + <&rpmcc RPM_SMD_XO_CLK_SRC>,
>> + <&gcc GCC_SDCC1_ICE_CORE_CLK>;
>> + clock-names = "iface",
>> + "core",
>> + "xo",
>> + "ice";
>> +
>> + resets = <&gcc GCC_SDCC1_BCR>;
>> +
>> + power-domains = <&rpmpd QCM2290_VDDCX>;
>> + iommus = <&apps_smmu 0xc0 0x0>;
>> +
>> + qcom,dll-config = <0x000f642c>;
>> + qcom,ddr-config = <0x80040868>;
>> + bus-width = <8>;
>> +
>> + status = "disabled";
>> + };
>> +
>> + sdhc_2: mmc@4784000 {
>> + compatible = "qcom,qcm2290-sdhci", "qcom,sdhci-msm-v5";
>> + reg = <0x0 0x04784000 0x0 0x1000>;
>> + reg-names = "hc";
>> +
>> + interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "hc_irq", "pwr_irq";
>> +
>> + clocks = <&gcc GCC_SDCC2_AHB_CLK>,
>> + <&gcc GCC_SDCC2_APPS_CLK>,
>> + <&rpmcc RPM_SMD_XO_CLK_SRC>;
>> + clock-names = "iface",
>> + "core",
>> + "xo";
>> +
>> + resets = <&gcc GCC_SDCC2_BCR>;
>> +
>> + power-domains = <&rpmpd QCM2290_VDDCX>;
>> + operating-points-v2 = <&sdhc2_opp_table>;
>> + iommus = <&apps_smmu 0xa0 0x0>;
>> +
>> + qcom,dll-config = <0x0007642c>;
>> + qcom,ddr-config = <0x80040868>;
>> + bus-width = <4>;
>> +
>> + status = "disabled";
>> +
>> + sdhc2_opp_table: opp-table {
>> + compatible = "operating-points-v2";
>> +
>> + opp-100000000 {
>> + opp-hz = /bits/ 64 <100000000>;
>> + required-opps = <&rpmpd_opp_low_svs>;
>> + };
>> +
>> + opp-202000000 {
>> + opp-hz = /bits/ 64 <202000000>;
>> + required-opps = <&rpmpd_opp_svs_plus>;
>> + };
>> + };
>> + };
>> +
>> + gpi_dma0: dma-controller@4a00000 {
>> + compatible = "qcom,qcm2290-gpi-dma", "qcom,sm6350-gpi-dma";
>> + reg = <0x0 0x04a00000 0x0 0x60000>;
>> + interrupts = <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>;
>> + dma-channels = <10>;
>> + dma-channel-mask = <0x1f>;
>> + iommus = <&apps_smmu 0xf6 0x0>;
>> + #dma-cells = <3>;
>> + status = "disabled";
>> + };
>> +
>> + qupv3_id_0: geniqup@4ac0000 {
>> + compatible = "qcom,geni-se-qup";
>> + reg = <0x0 0x04ac0000 0x0 0x2000>;
>> + clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
>> + <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
>> + clock-names = "m-ahb", "s-ahb";
>> + iommus = <&apps_smmu 0xe3 0x0>;
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> + ranges;
>> + status = "disabled";
>> +
>> + i2c0: i2c@4a80000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0x04a80000 0x0 0x4000>;
>> + interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
>> + clock-names = "se";
>> + pinctrl-0 = <&qup_i2c0_default>;
>> + pinctrl-names = "default";
>> + dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
>> + <&gpi_dma0 1 0 QCOM_GPI_I2C>;
>> + dma-names = "tx", "rx";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi0: spi@4a80000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0x04a80000 0x0 0x4000>;
>> + interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
>> + clock-names = "se";
>> + pinctrl-0 = <&qup_spi0_default>;
>> + pinctrl-names = "default";
>> + dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
>> + <&gpi_dma0 1 0 QCOM_GPI_SPI>;
>> + dma-names = "tx", "rx";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + uart0: serial@4a80000 {
>> + compatible = "qcom,geni-uart";
>> + reg = <0x0 0x04a80000 0x0 0x4000>;
>> + interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
>> + clock-names = "se";
>> + pinctrl-0 = <&qup_uart0_default>;
>> + pinctrl-names = "default";
>> + status = "disabled";
>> + };
>> +
>> + i2c1: i2c@4a84000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0x04a84000 0x0 0x4000>;
>> + interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
>> + clock-names = "se";
>> + pinctrl-0 = <&qup_i2c1_default>;
>> + pinctrl-names = "default";
>> + dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
>> + <&gpi_dma0 1 1 QCOM_GPI_I2C>;
>> + dma-names = "tx", "rx";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi1: spi@4a84000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0x04a84000 0x0 0x4000>;
>> + interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
>> + clock-names = "se";
>> + pinctrl-0 = <&qup_spi1_default>;
>> + pinctrl-names = "default";
>> + dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
>> + <&gpi_dma0 1 1 QCOM_GPI_SPI>;
>> + dma-names = "tx", "rx";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + i2c2: i2c@4a88000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0x04a88000 0x0 0x4000>;
>> + interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
>> + clock-names = "se";
>> + pinctrl-0 = <&qup_i2c2_default>;
>> + pinctrl-names = "default";
>> + dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
>> + <&gpi_dma0 1 2 QCOM_GPI_I2C>;
>> + dma-names = "tx", "rx";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi2: spi@4a88000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0x04a88000 0x0 0x4000>;
>> + interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
>> + clock-names = "se";
>> + pinctrl-0 = <&qup_spi2_default>;
>> + pinctrl-names = "default";
>> + dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
>> + <&gpi_dma0 1 2 QCOM_GPI_SPI>;
>> + dma-names = "tx", "rx";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + i2c3: i2c@4a8c000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0x04a8c000 0x0 0x4000>;
>> + interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
>> + clock-names = "se";
>> + pinctrl-0 = <&qup_i2c3_default>;
>> + pinctrl-names = "default";
>> + dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
>> + <&gpi_dma0 1 3 QCOM_GPI_I2C>;
>> + dma-names = "tx", "rx";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi3: spi@4a8c000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0x04a8c000 0x0 0x4000>;
>> + interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
>> + clock-names = "se";
>> + pinctrl-0 = <&qup_spi3_default>;
>> + pinctrl-names = "default";
>> + dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
>> + <&gpi_dma0 1 3 QCOM_GPI_SPI>;
>> + dma-names = "tx", "rx";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + i2c4: i2c@4a90000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0x04a90000 0x0 0x4000>;
>> + interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
>> + clock-names = "se";
>> + pinctrl-0 = <&qup_i2c4_default>;
>> + pinctrl-names = "default";
>> + dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
>> + <&gpi_dma0 1 4 QCOM_GPI_I2C>;
>> + dma-names = "tx", "rx";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi4: spi@4a90000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0x04a90000 0x0 0x4000>;
>> + interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_spi4_default>;
>> + dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
>> + <&gpi_dma0 1 4 QCOM_GPI_SPI>;
>> + dma-names = "tx", "rx";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + uart4: serial@4a90000 {
>> + compatible = "qcom,geni-uart";
>> + reg = <0x0 0x04a90000 0x0 0x4000>;
>> + interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
>> + clock-names = "se";
>> + pinctrl-0 = <&qup_uart4_default>;
>> + pinctrl-names = "default";
>> + status = "disabled";
>> + };
>> +
>> + i2c5: i2c@4a94000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0x04a94000 0x0 0x4000>;
>> + interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
>> + clock-names = "se";
>> + pinctrl-0 = <&qup_i2c5_default>;
>> + pinctrl-names = "default";
>> + dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
>> + <&gpi_dma0 1 5 QCOM_GPI_I2C>;
>> + dma-names = "tx", "rx";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi5: spi@4a94000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0x04a94000 0x0 0x4000>;
>> + interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
>> + clock-names = "se";
>> + pinctrl-0 = <&qup_spi5_default>;
>> + pinctrl-names = "default";
>> + dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
>> + <&gpi_dma0 1 5 QCOM_GPI_SPI>;
>> + dma-names = "tx", "rx";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + usb: usb@4ef8800 {
>> + compatible = "qcom,qcm2290-dwc3", "qcom,dwc3";
>> + reg = <0x0 0x04ef8800 0x0 0x400>;
>> + interrupts = <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "hs_phy_irq", "ss_phy_irq";
>> +
>> + clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
>> + <&gcc GCC_USB30_PRIM_MASTER_CLK>,
>> + <&gcc GCC_SYS_NOC_USB3_PRIM_AXI_CLK>,
>> + <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
>> + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
>> + <&gcc GCC_USB3_PRIM_CLKREF_CLK>;
>> + clock-names = "cfg_noc",
>> + "core",
>> + "iface",
>> + "sleep",
>> + "mock_utmi",
>> + "xo";
>> +
>> + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
>> + <&gcc GCC_USB30_PRIM_MASTER_CLK>;
>> + assigned-clock-rates = <19200000>, <133333333>;
>> +
>> + resets = <&gcc GCC_USB30_PRIM_BCR>;
>> + power-domains = <&gcc GCC_USB30_PRIM_GDSC>;
>> + wakeup-source;
>> +
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> + ranges;
>> +
>> + status = "disabled";
>> +
>> + usb_dwc3: usb@4e00000 {
>> + compatible = "snps,dwc3";
>> + reg = <0x0 0x04e00000 0x0 0xcd00>;
>> + interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
>> + phys = <&usb_hsphy>;
>> + phy-names = "usb2-phy";
>> + iommus = <&apps_smmu 0x120 0x0>;
>> + snps,dis_u2_susphy_quirk;
>> + snps,dis_enblslpm_quirk;
>> + snps,has-lpm-erratum;
>> + snps,hird-threshold = /bits/ 8 <0x10>;
>> + snps,usb3_lpm_capable;
>> + maximum-speed = "super-speed";
>> + dr_mode = "otg";
>> + };
>> + };
>> +
>> + remoteproc_mpss: remoteproc@6080000 {
>> + compatible = "qcom,qcm2290-mpss-pas", "qcom,sm6115-mpss-pas";
>> + reg = <0x0 0x06080000 0x0 0x100>;
>> +
>> + interrupts-extended = <&intc GIC_SPI 307 IRQ_TYPE_EDGE_RISING>,
>> + <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
>> + <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
>> + <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
>> + <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
>> + <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
>> + interrupt-names = "wdog",
>> + "fatal",
>> + "ready",
>> + "handover",
>> + "stop-ack",
>> + "shutdown-ack";
>> +
>> + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
>> + clock-names = "xo";
>> +
>> + power-domains = <&rpmpd QCM2290_VDDCX>;
>> +
>> + memory-region = <&pil_modem_mem>;
>> +
>> + qcom,smem-states = <&modem_smp2p_out 0>;
>> + qcom,smem-state-names = "stop";
>> +
>> + status = "disabled";
>> +
>> + glink-edge {
>> + interrupts = <GIC_SPI 68 IRQ_TYPE_EDGE_RISING>;
>> + label = "mpss";
>> + qcom,remote-pid = <1>;
>> + mboxes = <&apcs_glb 12>;
>> + };
>> + };
>> +
>> + remoteproc_adsp: remoteproc@ab00000 {
>> + compatible = "qcom,qcm2290-adsp-pas", "qcom,sm6115-adsp-pas";
>> + reg = <0x0 0x0ab00000 0x0 0x100>;
>> +
>> + interrupts-extended = <&intc GIC_SPI 282 IRQ_TYPE_EDGE_RISING>,
>> + <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
>> + <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
>> + <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
>> + <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
>> + interrupt-names = "wdog",
>> + "fatal",
>> + "ready",
>> + "handover",
>> + "stop-ack";
>> +
>> + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
>> + clock-names = "xo";
>> +
>> + power-domains = <&rpmpd QCM2290_VDD_LPI_CX>,
>> + <&rpmpd QCM2290_VDD_LPI_MX>;
>> +
>> + memory-region = <&pil_adsp_mem>;
>> +
>> + qcom,smem-states = <&adsp_smp2p_out 0>;
>> + qcom,smem-state-names = "stop";
>> +
>> + status = "disabled";
>> +
>> + glink-edge {
>> + interrupts = <GIC_SPI 277 IRQ_TYPE_EDGE_RISING>;
>> + label = "lpass";
>> + qcom,remote-pid = <2>;
>> + mboxes = <&apcs_glb 8>;
>> + };
>> + };
>> +
>> + apps_smmu: iommu@c600000 {
>> + compatible = "qcom,qcm2290-smmu-500", "qcom,smmu-500", "arm,mmu-500";
>> + reg = <0x0 0x0c600000 0x0 0x80000>;
>> + #iommu-cells = <2>;
>> + #global-interrupts = <1>;
>> +
>> + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
>> + };
>> +
>> + wifi: wifi@c800000 {
>> + compatible = "qcom,wcn3990-wifi";
>> + reg = <0x0 0x0c800000 0x0 0x800000>;
>> + reg-names = "membase";
>> + memory-region = <&wlan_msa_mem>;
>> + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 362 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 364 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 366 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 367 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
>> + iommus = <&apps_smmu 0x1a0 0x1>;
>> + qcom,msa-fixed-perm;
>> + status = "disabled";
>> + };
>> +
>> + watchdog@f017000 {
>> + compatible = "qcom,apss-wdt-qcm2290", "qcom,kpss-wdt";
>> + reg = <0x0 0x0f017000 0x0 0x1000>;
>> + interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>,
>> + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&sleep_clk>;
>> + };
>> +
>> + apcs_glb: mailbox@f111000 {
>> + compatible = "qcom,qcm2290-apcs-hmss-global";
>> + reg = <0x0 0x0f111000 0x0 0x1000>;
>> + #mbox-cells = <1>;
>> + };
>> +
>> + timer@f120000 {
>> + compatible = "arm,armv7-timer-mem";
>> + reg = <0x0 0x0f120000 0x0 0x1000>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0 0x0 0x0f121000 0x8000>;
>> +
>> + frame@0 {
>> + reg = <0x0 0x1000>,
>> + <0x1000 0x1000>;
>> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
>> + frame-number = <0>;
>> + };
>> +
>> + frame@2000 {
>> + reg = <0x2000 0x1000>;
>> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
>> + frame-number = <1>;
>> + status = "disabled";
>> + };
>> +
>> + frame@3000 {
>> + reg = <0x3000 0x1000>;
>> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
>> + frame-number = <2>;
>> + status = "disabled";
>> + };
>> +
>> + frame@4000 {
>> + reg = <0x4000 0x1000>;
>> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
>> + frame-number = <3>;
>> + status = "disabled";
>> + };
>> +
>> + frame@5000 {
>> + reg = <0x5000 0x1000>;
>> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
>> + frame-number = <4>;
>> + status = "disabled";
>> + };
>> +
>> + frame@6000 {
>> + reg = <0x6000 0x1000>;
>> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
>> + frame-number = <5>;
>> + status = "disabled";
>> + };
>> +
>> + frame@7000 {
>> + reg = <0x7000 0x1000>;
>> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
>> + frame-number = <6>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + intc: interrupt-controller@f200000 {
>> + compatible = "arm,gic-v3";
>> + reg = <0x0 0x0f200000 0x0 0x10000>,
>> + <0x0 0x0f300000 0x0 0x100000>;
>> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
>> + #interrupt-cells = <3>;
>> + interrupt-controller;
>> + interrupt-parent = <&intc>;
>> + #redistributor-regions = <1>;
>> + redistributor-stride = <0x0 0x20000>;
>> + };
>> +
>> + cpufreq_hw: cpufreq@f521000 {
>> + compatible = "qcom,qcm2290-cpufreq-hw", "qcom,cpufreq-hw";
>> + reg = <0x0 0x0f521000 0x0 0x1000>;
>> + reg-names = "freq-domain0";
>> + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "dcvsh-irq-0";
>> + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, <&gcc GPLL0>;
>> + clock-names = "xo", "alternate";
>> +
>> + #freq-domain-cells = <1>;
>> + #clock-cells = <1>;
>> + };
>> + };
>> +
>> + thermal-zones {
>> + mapss-thermal {
>> + polling-delay-passive = <0>;
>> + polling-delay = <0>;
>> +
>> + thermal-sensors = <&tsens0 0>;
>> +
>> + trips {
>> + mapss_alert0: trip-point0 {
>> + temperature = <90000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + mapss_alert1: trip-point1 {
>> + temperature = <95000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + mapss_crit: mapss-crit {
>> + temperature = <110000>;
>> + hysteresis = <1000>;
>> + type = "critical";
>> + };
>> + };
>> + };
>> +
>> + video-thermal {
>> + polling-delay-passive = <0>;
>> + polling-delay = <0>;
>> +
>> + thermal-sensors = <&tsens0 1>;
>> +
>> + trips {
>> + video_alert0: trip-point0 {
>> + temperature = <90000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + video_alert1: trip-point1 {
>> + temperature = <95000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + video_crit: video-crit {
>> + temperature = <110000>;
>> + hysteresis = <1000>;
>> + type = "critical";
>> + };
>> + };
>> + };
>> +
>> + wlan-thermal {
>> + polling-delay-passive = <0>;
>> + polling-delay = <0>;
>> +
>> + thermal-sensors = <&tsens0 2>;
>> +
>> + trips {
>> + wlan_alert0: trip-point0 {
>> + temperature = <90000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + wlan_alert1: trip-point1 {
>> + temperature = <95000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + wlan_crit: wlan-crit {
>> + temperature = <110000>;
>> + hysteresis = <1000>;
>> + type = "critical";
>> + };
>> + };
>> + };
>> +
>> + cpuss0-thermal {
>> + polling-delay-passive = <0>;
>> + polling-delay = <0>;
>> +
>> + thermal-sensors = <&tsens0 3>;
>> +
>> + trips {
>> + cpuss0_alert0: trip-point0 {
>> + temperature = <90000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + cpuss0_alert1: trip-point1 {
>> + temperature = <95000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + cpuss0_crit: cpuss0-crit {
>> + temperature = <110000>;
>> + hysteresis = <1000>;
>> + type = "critical";
>> + };
>> + };
>> + };
>> +
>> + cpuss1-thermal {
>> + polling-delay-passive = <0>;
>> + polling-delay = <0>;
>> +
>> + thermal-sensors = <&tsens0 4>;
>> +
>> + trips {
>> + cpuss1_alert0: trip-point0 {
>> + temperature = <90000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + cpuss1_alert1: trip-point1 {
>> + temperature = <95000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + cpuss1_crit: cpuss1-crit {
>> + temperature = <110000>;
>> + hysteresis = <1000>;
>> + type = "critical";
>> + };
>> + };
>> + };
>> +
>> + mdm0-thermal {
>> + polling-delay-passive = <0>;
>> + polling-delay = <0>;
>> +
>> + thermal-sensors = <&tsens0 5>;
>> +
>> + trips {
>> + mdm0_alert0: trip-point0 {
>> + temperature = <90000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + mdm0_alert1: trip-point1 {
>> + temperature = <95000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + mdm0_crit: mdm0-crit {
>> + temperature = <110000>;
>> + hysteresis = <1000>;
>> + type = "critical";
>> + };
>> + };
>> + };
>> +
>> + mdm1-thermal {
>> + polling-delay-passive = <0>;
>> + polling-delay = <0>;
>> +
>> + thermal-sensors = <&tsens0 6>;
>> +
>> + trips {
>> + mdm1_alert0: trip-point0 {
>> + temperature = <90000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + mdm1_alert1: trip-point1 {
>> + temperature = <95000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + mdm1_crit: mdm1-crit {
>> + temperature = <110000>;
>> + hysteresis = <1000>;
>> + type = "critical";
>> + };
>> + };
>> + };
>> +
>> + gpu-thermal {
>> + polling-delay-passive = <0>;
>> + polling-delay = <0>;
>> +
>> + thermal-sensors = <&tsens0 7>;
>> +
>> + trips {
>> + gpu_alert0: trip-point0 {
>> + temperature = <90000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + gpu_alert1: trip-point1 {
>> + temperature = <95000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + gpu_crit: gpu-crit {
>> + temperature = <110000>;
>> + hysteresis = <1000>;
>> + type = "critical";
>> + };
>> + };
>> + };
>> +
>> + hm-center-thermal {
>> + polling-delay-passive = <0>;
>> + polling-delay = <0>;
>> +
>> + thermal-sensors = <&tsens0 8>;
>> +
>> + trips {
>> + hm_center_alert0: trip-point0 {
>> + temperature = <90000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + hm_center_alert1: trip-point1 {
>> + temperature = <95000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + hm_center_crit: hm-center-crit {
>> + temperature = <110000>;
>> + hysteresis = <1000>;
>> + type = "critical";
>> + };
>> + };
>> + };
>> +
>> + camera-thermal {
>> + polling-delay-passive = <0>;
>> + polling-delay = <0>;
>> +
>> + thermal-sensors = <&tsens0 9>;
>> +
>> + trips {
>> + camera_alert0: trip-point0 {
>> + temperature = <90000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + camera_alert1: trip-point1 {
>> + temperature = <95000>;
>> + hysteresis = <2000>;
>> + type = "passive";
>> + };
>> +
>> + camera_crit: camera-crit {
>> + temperature = <110000>;
>> + hysteresis = <1000>;
>> + type = "critical";
>> + };
>> + };
>> + };
>> + };
>> +
>> + timer {
>> + compatible = "arm,armv8-timer";
>> + interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> + <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> + <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
>> + };
>> +};
>>
>> --
>> 2.40.0
>>
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v2 2/5] dt-bindings: arm: qcom: Add QRB2210/QCM2290 and RB1 board
2023-04-05 15:50 ` [PATCH v2 2/5] dt-bindings: arm: qcom: Add QRB2210/QCM2290 and RB1 board Konrad Dybcio
@ 2023-04-07 18:59 ` Krzysztof Kozlowski
0 siblings, 0 replies; 10+ messages in thread
From: Krzysztof Kozlowski @ 2023-04-07 18:59 UTC (permalink / raw)
To: Konrad Dybcio, Andy Gross, Bjorn Andersson, Rob Herring,
Krzysztof Kozlowski, Robert Marko, Das Srinagesh
Cc: Bhupesh Sharma, Vladimir Zapolskiy, Marijn Suijten,
linux-arm-msm, devicetree, linux-kernel
On 05/04/2023 17:50, Konrad Dybcio wrote:
> Document QRB210, a QRB version of QCM2290.
>
> Document QTI Robotics RB1 as a QRB2210 device.
>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
> Documentation/devicetree/bindings/arm/qcom.yaml | 9 +++++++++
> 1 file changed, 9 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
> index 05badce5fedc..236ea55aee96 100644
> --- a/Documentation/devicetree/bindings/arm/qcom.yaml
> +++ b/Documentation/devicetree/bindings/arm/qcom.yaml
> @@ -47,6 +47,8 @@ description: |
> msm8996
> msm8998
> qcs404
> + qcm2290
> + qrb2210
> qdu1000
> qru1000
> sa8155p
> @@ -353,6 +355,13 @@ properties:
> - const: swir,wp8548
> - const: qcom,mdm9615
>
> + - description: Qualcomm Technologies, Inc. Robotics RB1
The title should be now different, e.g.
Qualcomm Technologies, Inc. QRB2210-based boards
or even dropped entirely.
Anyway, this can be fixed when a new entry appears here.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2023-04-07 19:01 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-04-05 15:50 [PATCH v2 0/5] RB1 + QCM2290 support Konrad Dybcio
2023-04-05 15:50 ` [PATCH v2 1/5] dt-bindings: firmware: document Qualcomm QCM2290 SCM Konrad Dybcio
2023-04-05 15:50 ` [PATCH v2 2/5] dt-bindings: arm: qcom: Add QRB2210/QCM2290 and RB1 board Konrad Dybcio
2023-04-07 18:59 ` Krzysztof Kozlowski
2023-04-05 15:50 ` [PATCH v2 3/5] arm64: dts: qcom: Add initial QCM2290 device tree Konrad Dybcio
2023-04-07 18:35 ` Bjorn Andersson
2023-04-07 18:47 ` Konrad Dybcio
2023-04-05 15:50 ` [PATCH v2 4/5] arm64: dts: qcom: Add initial PM2250 " Konrad Dybcio
2023-04-05 15:50 ` [PATCH v2 5/5] arm64: dts: qcom: Add initial QTI RB1 " Konrad Dybcio
2023-04-07 18:36 ` (subset) [PATCH v2 0/5] RB1 + QCM2290 support Bjorn Andersson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).