* [PATCH v2 0/2] ATH10K YAML conversion
@ 2023-04-06 11:54 Konrad Dybcio
2023-04-06 11:54 ` [PATCH v2 1/2] dt-bindings: net: Convert ATH10K to YAML Konrad Dybcio
2023-04-06 11:54 ` [PATCH v2 2/2] arm64: dts: qcom: sdm845-polaris: Drop inexistent properties Konrad Dybcio
0 siblings, 2 replies; 5+ messages in thread
From: Konrad Dybcio @ 2023-04-06 11:54 UTC (permalink / raw)
To: Kalle Valo, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Andy Gross,
Bjorn Andersson
Cc: Marijn Suijten, ath10k, linux-wireless, netdev, devicetree,
linux-kernel, linux-arm-msm, Konrad Dybcio, Krzysztof Kozlowski
v1 -> v2:
Dropped:
- '|' in /description
- /properties/resets/minItems
- Unnecessary level of 'items:' in /properties/ext-fem-name
- reserved-memory in examples
- status in examples
- labels in examples
Added:
- /properties/wifi-firmware/additionalProperties: false
- /properties/wifi-firmware/properties/iommus
- /properties/qcom,coexist-support/enum (and reworded the description)
- wifi-firmware and supplies in the SNoC example
Patch 2 is unchanged, picked up rb.
v1: https://lore.kernel.org/r/20230406-topic-ath10k_bindings-v1-0-1ef181c50236@linaro.org
This is my attempt at (finally) moving ATH10K to YAML.
One inexistent dt property came out as part of that.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
Konrad Dybcio (2):
dt-bindings: net: Convert ATH10K to YAML
arm64: dts: qcom: sdm845-polaris: Drop inexistent properties
.../bindings/net/wireless/qcom,ath10k.txt | 215 ------------
.../bindings/net/wireless/qcom,ath10k.yaml | 359 +++++++++++++++++++++
arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts | 2 -
3 files changed, 359 insertions(+), 217 deletions(-)
---
base-commit: 8417c8f5007bf4567ccffda850a3157c7d905f67
change-id: 20230406-topic-ath10k_bindings-9af5fa834235
Best regards,
--
Konrad Dybcio <konrad.dybcio@linaro.org>
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v2 1/2] dt-bindings: net: Convert ATH10K to YAML
2023-04-06 11:54 [PATCH v2 0/2] ATH10K YAML conversion Konrad Dybcio
@ 2023-04-06 11:54 ` Konrad Dybcio
2023-04-06 12:47 ` Rob Herring
2023-04-06 11:54 ` [PATCH v2 2/2] arm64: dts: qcom: sdm845-polaris: Drop inexistent properties Konrad Dybcio
1 sibling, 1 reply; 5+ messages in thread
From: Konrad Dybcio @ 2023-04-06 11:54 UTC (permalink / raw)
To: Kalle Valo, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Andy Gross,
Bjorn Andersson
Cc: Marijn Suijten, ath10k, linux-wireless, netdev, devicetree,
linux-kernel, linux-arm-msm, Konrad Dybcio
Convert the ATH10K bindings to YAML.
Dropped properties that are absent at the current state of mainline:
- qcom,msi_addr
- qcom,msi_base
qcom,coexist-support and qcom,coexist-gpio-pin do very little and should
be reconsidered on the driver side, especially the latter one.
Somewhat based on the ath11k bindings.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
.../bindings/net/wireless/qcom,ath10k.txt | 215 ------------
.../bindings/net/wireless/qcom,ath10k.yaml | 359 +++++++++++++++++++++
2 files changed, 359 insertions(+), 215 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
deleted file mode 100644
index b61c2d5a0ff7..000000000000
--- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
+++ /dev/null
@@ -1,215 +0,0 @@
-* Qualcomm Atheros ath10k wireless devices
-
-Required properties:
-- compatible: Should be one of the following:
- * "qcom,ath10k"
- * "qcom,ipq4019-wifi"
- * "qcom,wcn3990-wifi"
-
-PCI based devices uses compatible string "qcom,ath10k" and takes calibration
-data along with board specific data via "qcom,ath10k-calibration-data".
-Rest of the properties are not applicable for PCI based devices.
-
-AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi"
-and also uses most of the properties defined in this doc (except
-"qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data"
-to carry pre calibration data.
-
-In general, entry "qcom,ath10k-pre-calibration-data" and
-"qcom,ath10k-calibration-data" conflict with each other and only one
-can be provided per device.
-
-SNOC based devices (i.e. wcn3990) uses compatible string "qcom,wcn3990-wifi".
-
-- reg: Address and length of the register set for the device.
-- reg-names: Must include the list of following reg names,
- "membase"
-- interrupts: reference to the list of 17 interrupt numbers for "qcom,ipq4019-wifi"
- compatible target.
- reference to the list of 12 interrupt numbers for "qcom,wcn3990-wifi"
- compatible target.
- Must contain interrupt-names property per entry for
- "qcom,ath10k", "qcom,ipq4019-wifi" compatible targets.
-
-- interrupt-names: Must include the entries for MSI interrupt
- names ("msi0" to "msi15") and legacy interrupt
- name ("legacy") for "qcom,ath10k", "qcom,ipq4019-wifi"
- compatible targets.
-
-Optional properties:
-- resets: Must contain an entry for each entry in reset-names.
- See ../reset/reseti.txt for details.
-- reset-names: Must include the list of following reset names,
- "wifi_cpu_init"
- "wifi_radio_srif"
- "wifi_radio_warm"
- "wifi_radio_cold"
- "wifi_core_warm"
- "wifi_core_cold"
-- clocks: List of clock specifiers, must contain an entry for each required
- entry in clock-names.
-- clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref",
- "wifi_wcss_rtc" for "qcom,ipq4019-wifi" compatible target and
- "cxo_ref_clk_pin" and optionally "qdss" for "qcom,wcn3990-wifi"
- compatible target.
-- qcom,msi_addr: MSI interrupt address.
-- qcom,msi_base: Base value to add before writing MSI data into
- MSI address register.
-- qcom,ath10k-calibration-variant: string to search for in the board-2.bin
- variant list with the same bus and device
- specific ids
-- qcom,ath10k-calibration-data : calibration data + board specific data
- as an array, the length can vary between
- hw versions.
-- qcom,ath10k-pre-calibration-data : pre calibration data as an array,
- the length can vary between hw versions.
-- <supply-name>-supply: handle to the regulator device tree node
- optional "supply-name" are "vdd-0.8-cx-mx",
- "vdd-1.8-xo", "vdd-1.3-rfa", "vdd-3.3-ch0",
- and "vdd-3.3-ch1".
-- memory-region:
- Usage: optional
- Value type: <phandle>
- Definition: reference to the reserved-memory for the msa region
- used by the wifi firmware running in Q6.
-- iommus:
- Usage: optional
- Value type: <prop-encoded-array>
- Definition: A list of phandle and IOMMU specifier pairs.
-- ext-fem-name:
- Usage: Optional
- Value type: string
- Definition: Name of external front end module used. Some valid FEM names
- for example: "microsemi-lx5586", "sky85703-11"
- and "sky85803" etc.
-- qcom,snoc-host-cap-8bit-quirk:
- Usage: Optional
- Value type: <empty>
- Definition: Quirk specifying that the firmware expects the 8bit version
- of the host capability QMI request
-- qcom,xo-cal-data: xo cal offset to be configured in xo trim register.
-
-- qcom,msa-fixed-perm: Boolean context flag to disable SCM call for statically
- mapped msa region.
-
-- qcom,coexist-support : should contain eithr "0" or "1" to indicate coex
- support by the hardware.
-- qcom,coexist-gpio-pin : gpio pin number information to support coex
- which will be used by wifi firmware.
-
-* Subnodes
-The ath10k wifi node can contain one optional firmware subnode.
-Firmware subnode is needed when the platform does not have TustZone.
-The firmware subnode must have:
-
-- iommus:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: A list of phandle and IOMMU specifier pairs.
-
-
-Example (to supply PCI based wifi block details):
-
-In this example, the node is defined as child node of the PCI controller.
-
-pci {
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
-
- wifi@0,0 {
- reg = <0 0 0 0 0>;
- qcom,ath10k-calibration-data = [ 01 02 03 ... ];
- ext-fem-name = "microsemi-lx5586";
- };
- };
-};
-
-Example (to supply ipq4019 SoC wifi block details):
-
-wifi0: wifi@a000000 {
- compatible = "qcom,ipq4019-wifi";
- reg = <0xa000000 0x200000>;
- resets = <&gcc WIFI0_CPU_INIT_RESET>,
- <&gcc WIFI0_RADIO_SRIF_RESET>,
- <&gcc WIFI0_RADIO_WARM_RESET>,
- <&gcc WIFI0_RADIO_COLD_RESET>,
- <&gcc WIFI0_CORE_WARM_RESET>,
- <&gcc WIFI0_CORE_COLD_RESET>;
- reset-names = "wifi_cpu_init",
- "wifi_radio_srif",
- "wifi_radio_warm",
- "wifi_radio_cold",
- "wifi_core_warm",
- "wifi_core_cold";
- clocks = <&gcc GCC_WCSS2G_CLK>,
- <&gcc GCC_WCSS2G_REF_CLK>,
- <&gcc GCC_WCSS2G_RTC_CLK>;
- clock-names = "wifi_wcss_cmd",
- "wifi_wcss_ref",
- "wifi_wcss_rtc";
- interrupts = <0 0x20 0x1>,
- <0 0x21 0x1>,
- <0 0x22 0x1>,
- <0 0x23 0x1>,
- <0 0x24 0x1>,
- <0 0x25 0x1>,
- <0 0x26 0x1>,
- <0 0x27 0x1>,
- <0 0x28 0x1>,
- <0 0x29 0x1>,
- <0 0x2a 0x1>,
- <0 0x2b 0x1>,
- <0 0x2c 0x1>,
- <0 0x2d 0x1>,
- <0 0x2e 0x1>,
- <0 0x2f 0x1>,
- <0 0xa8 0x0>;
- interrupt-names = "msi0", "msi1", "msi2", "msi3",
- "msi4", "msi5", "msi6", "msi7",
- "msi8", "msi9", "msi10", "msi11",
- "msi12", "msi13", "msi14", "msi15",
- "legacy";
- qcom,msi_addr = <0x0b006040>;
- qcom,msi_base = <0x40>;
- qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ];
- qcom,coexist-support = <1>;
- qcom,coexist-gpio-pin = <0x33>;
-};
-
-Example (to supply wcn3990 SoC wifi block details):
-
-wifi@18000000 {
- compatible = "qcom,wcn3990-wifi";
- reg = <0x18800000 0x800000>;
- reg-names = "membase";
- clocks = <&clock_gcc clk_rf_clk2_pin>;
- clock-names = "cxo_ref_clk_pin";
- interrupts =
- <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>;
- vdd-0.8-cx-mx-supply = <&pm8998_l5>;
- vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
- vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
- vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
- vdd-3.3-ch1-supply = <&vreg_l26a_3p3>;
- memory-region = <&wifi_msa_mem>;
- iommus = <&apps_smmu 0x0040 0x1>;
- qcom,msa-fixed-perm;
- wifi-firmware {
- iommus = <&apps_iommu 0xc22 0x1>;
- };
-};
diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml
new file mode 100644
index 000000000000..8920ad3f4636
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml
@@ -0,0 +1,359 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/wireless/qcom,ath10k.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies ATH10K wireless devices
+
+maintainers:
+ - Kalle Valo <kvalo@kernel.org>
+
+description:
+ Qualcomm Technologies, Inc. IEEE 802.11ac devices.
+
+properties:
+ compatible:
+ enum:
+ - qcom,ath10k # SDIO-based devices
+ - qcom,ipq4019-wifi
+ - qcom,wcn3990-wifi # SNoC-based devices
+
+ reg:
+ maxItems: 1
+
+ reg-names:
+ items:
+ - const: membase
+
+ interrupts:
+ minItems: 12
+ maxItems: 17
+
+ interrupt-names:
+ minItems: 12
+ maxItems: 17
+
+ memory-region:
+ maxItems: 1
+ description:
+ Reference to the MSA memory region used by the Wi-Fi firmware
+ running on the Q6 core.
+
+ iommus:
+ minItems: 1
+ maxItems: 2
+
+ clocks:
+ minItems: 1
+ maxItems: 3
+
+ clock-names:
+ minItems: 1
+ maxItems: 3
+
+ resets:
+ maxItems: 6
+
+ reset-names:
+ items:
+ - const: wifi_cpu_init
+ - const: wifi_radio_srif
+ - const: wifi_radio_warm
+ - const: wifi_radio_cold
+ - const: wifi_core_warm
+ - const: wifi_core_cold
+
+ ext-fem-name:
+ $ref: /schemas/types.yaml#/definitions/string
+ description: Name of external front end module used.
+ enum:
+ - microsemi-lx5586
+ - sky85703-11
+ - sky85803
+
+ wifi-firmware:
+ type: object
+ additionalProperties: false
+ description: |
+ The ATH10K Wi-Fi node can contain one optional firmware subnode.
+ Firmware subnode is needed when the platform does not have Trustzone.
+ properties:
+ iommus:
+ maxItems: 1
+ required:
+ - iommus
+
+ qcom,ath10k-calibration-data:
+ $ref: /schemas/types.yaml#/definitions/uint8-array
+ description:
+ Calibration data + board-specific data as a byte array. The length
+ can vary between hardware versions.
+
+ qcom,ath10k-calibration-variant:
+ $ref: /schemas/types.yaml#/definitions/string
+ description:
+ Unique variant identifier of the calibration data in board-2.bin
+ for designs with colliding bus and device specific ids
+
+ qcom,ath10k-pre-calibration-data:
+ $ref: /schemas/types.yaml#/definitions/uint8-array
+ description:
+ Pre-calibration data as a byte array. The length can vary between
+ hardware versions.
+
+ qcom,coexist-support:
+ $ref: /schemas/types.yaml#/definitions/uint8
+ enum: [0, 1]
+ description:
+ Indicate coex support by the hardware.
+
+ qcom,coexist-gpio-pin:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ COEX GPIO number provided to the Wi-Fi firmware.
+
+ qcom,msa-fixed-perm:
+ type: boolean
+ description:
+ Whether to skip executing an SCM call that reassigns the memory
+ region ownership.
+
+ qcom,smem-states:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ description: State bits used by the AP to signal the WLAN Q6.
+ items:
+ - description: Signal bits used to enable/disable low power mode
+ on WCN in the case of WoW (Wake on Wireless).
+
+ qcom,smem-state-names:
+ description: The names of the state bits used for SMP2P output.
+ items:
+ - const: wlan-smp2p-out
+
+ qcom,snoc-host-cap-8bit-quirk:
+ type: boolean
+ description:
+ Quirk specifying that the firmware expects the 8bit version
+ of the host capability QMI request
+
+ qcom,xo-cal-data:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ XO cal offset to be configured in XO trim register.
+
+ vdd-0.8-cx-mx-supply:
+ description: Main logic power rail
+
+ vdd-1.8-xo-supply:
+ description: Crystal oscillator supply
+
+ vdd-1.3-rfa-supply:
+ description: RFA supply
+
+ vdd-3.3-ch0-supply:
+ description: Primary Wi-Fi antenna supply
+
+ vdd-3.3-ch1-supply:
+ description: Secondary Wi-Fi antenna supply
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,ipq4019-wifi
+ then:
+ properties:
+ interrupts:
+ minItems: 17
+ maxItems: 17
+
+ interrupt-names:
+ minItems: 17
+ items:
+ - const: msi0
+ - const: msi1
+ - const: msi2
+ - const: msi3
+ - const: msi4
+ - const: msi5
+ - const: msi6
+ - const: msi7
+ - const: msi8
+ - const: msi9
+ - const: msi10
+ - const: msi11
+ - const: msi12
+ - const: msi13
+ - const: msi14
+ - const: msi15
+ - const: legacy
+
+ clocks:
+ items:
+ - description: Wi-Fi command clock
+ - description: Wi-Fi reference clock
+ - description: Wi-Fi RTC clock
+
+ clock-names:
+ items:
+ - const: wifi_wcss_cmd
+ - const: wifi_wcss_ref
+ - const: wifi_wcss_rtc
+
+ required:
+ - clocks
+ - clock-names
+ - interrupts
+ - interrupt-names
+ - resets
+ - reset-names
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,wcn3990-wifi
+
+ then:
+ properties:
+ clocks:
+ minItems: 1
+ items:
+ - description: XO reference clock
+ - description: Qualcomm Debug Subsystem clock
+
+ clock-names:
+ minItems: 1
+ items:
+ - const: cxo_ref_clk_pin
+ - const: qdss
+
+ interrupts:
+ items:
+ - description: CE0
+ - description: CE1
+ - description: CE2
+ - description: CE3
+ - description: CE4
+ - description: CE5
+ - description: CE6
+ - description: CE7
+ - description: CE8
+ - description: CE9
+ - description: CE10
+ - description: CE11
+
+ required:
+ - interrupts
+
+examples:
+ # SNoC
+ - |
+ #include <dt-bindings/clock/qcom,rpmcc.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ wifi@18800000 {
+ compatible = "qcom,wcn3990-wifi";
+ reg = <0x18800000 0x800000>;
+ reg-names = "membase";
+ memory-region = <&wlan_msa_mem>;
+ clocks = <&rpmcc RPM_SMD_RF_CLK2_PIN>;
+ clock-names = "cxo_ref_clk_pin";
+ interrupts = <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&anoc2_smmu 0x1900>,
+ <&anoc2_smmu 0x1901>;
+ qcom,snoc-host-cap-8bit-quirk;
+ vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+ vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+ vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+ vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+ vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
+
+ wifi-firmware {
+ wifi-firmware {
+ iommus = <&apps_smmu 0x1c02 0x1>;
+ };
+ };
+ };
+
+ # AHB
+ - |
+ #include <dt-bindings/clock/qcom,gcc-ipq4019.h>
+
+ wifi@a000000 {
+ compatible = "qcom,ipq4019-wifi";
+ reg = <0xa000000 0x200000>;
+ resets = <&gcc WIFI0_CPU_INIT_RESET>,
+ <&gcc WIFI0_RADIO_SRIF_RESET>,
+ <&gcc WIFI0_RADIO_WARM_RESET>,
+ <&gcc WIFI0_RADIO_COLD_RESET>,
+ <&gcc WIFI0_CORE_WARM_RESET>,
+ <&gcc WIFI0_CORE_COLD_RESET>;
+ reset-names = "wifi_cpu_init",
+ "wifi_radio_srif",
+ "wifi_radio_warm",
+ "wifi_radio_cold",
+ "wifi_core_warm",
+ "wifi_core_cold";
+ clocks = <&gcc GCC_WCSS2G_CLK>,
+ <&gcc GCC_WCSS2G_REF_CLK>,
+ <&gcc GCC_WCSS2G_RTC_CLK>;
+ clock-names = "wifi_wcss_cmd",
+ "wifi_wcss_ref",
+ "wifi_wcss_rtc";
+ interrupts = <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 38 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 39 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 40 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 41 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 42 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 43 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 44 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 45 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 46 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 47 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi0",
+ "msi1",
+ "msi2",
+ "msi3",
+ "msi4",
+ "msi5",
+ "msi6",
+ "msi7",
+ "msi8",
+ "msi9",
+ "msi10",
+ "msi11",
+ "msi12",
+ "msi13",
+ "msi14",
+ "msi15",
+ "legacy";
+ };
--
2.40.0
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH v2 2/2] arm64: dts: qcom: sdm845-polaris: Drop inexistent properties
2023-04-06 11:54 [PATCH v2 0/2] ATH10K YAML conversion Konrad Dybcio
2023-04-06 11:54 ` [PATCH v2 1/2] dt-bindings: net: Convert ATH10K to YAML Konrad Dybcio
@ 2023-04-06 11:54 ` Konrad Dybcio
1 sibling, 0 replies; 5+ messages in thread
From: Konrad Dybcio @ 2023-04-06 11:54 UTC (permalink / raw)
To: Kalle Valo, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Andy Gross,
Bjorn Andersson
Cc: Marijn Suijten, ath10k, linux-wireless, netdev, devicetree,
linux-kernel, linux-arm-msm, Konrad Dybcio, Krzysztof Kozlowski
Drop the qcom,snoc-host-cap-skip-quirk that was never introduced to
solve schema warnings.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts | 2 --
1 file changed, 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts
index 1b7fdbae6a2b..56f2d855df78 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts
@@ -712,7 +712,5 @@ &wifi {
vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
-
- qcom,snoc-host-cap-skip-quirk;
status = "okay";
};
--
2.40.0
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: net: Convert ATH10K to YAML
2023-04-06 11:54 ` [PATCH v2 1/2] dt-bindings: net: Convert ATH10K to YAML Konrad Dybcio
@ 2023-04-06 12:47 ` Rob Herring
2023-04-06 12:52 ` Konrad Dybcio
0 siblings, 1 reply; 5+ messages in thread
From: Rob Herring @ 2023-04-06 12:47 UTC (permalink / raw)
To: Konrad Dybcio
Cc: Eric Dumazet, linux-wireless, Krzysztof Kozlowski, devicetree,
David S. Miller, linux-kernel, Paolo Abeni, Rob Herring, netdev,
Bjorn Andersson, Kalle Valo, Andy Gross, Marijn Suijten,
linux-arm-msm, Jakub Kicinski, ath10k
On Thu, 06 Apr 2023 13:54:04 +0200, Konrad Dybcio wrote:
> Convert the ATH10K bindings to YAML.
>
> Dropped properties that are absent at the current state of mainline:
> - qcom,msi_addr
> - qcom,msi_base
>
> qcom,coexist-support and qcom,coexist-gpio-pin do very little and should
> be reconsidered on the driver side, especially the latter one.
>
> Somewhat based on the ath11k bindings.
>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
> .../bindings/net/wireless/qcom,ath10k.txt | 215 ------------
> .../bindings/net/wireless/qcom,ath10k.yaml | 359 +++++++++++++++++++++
> 2 files changed, 359 insertions(+), 215 deletions(-)
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.example.dtb: wifi@18800000: wifi-firmware: 'wifi-firmware' does not match any of the regexes: 'pinctrl-[0-9]+'
From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.example.dtb: wifi@18800000: wifi-firmware: 'iommus' is a required property
From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml
doc reference errors (make refcheckdocs):
MAINTAINERS: Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230406-topic-ath10k_bindings-v2-1-557f884a65d1@linaro.org
The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: net: Convert ATH10K to YAML
2023-04-06 12:47 ` Rob Herring
@ 2023-04-06 12:52 ` Konrad Dybcio
0 siblings, 0 replies; 5+ messages in thread
From: Konrad Dybcio @ 2023-04-06 12:52 UTC (permalink / raw)
To: Rob Herring
Cc: Eric Dumazet, linux-wireless, Krzysztof Kozlowski, devicetree,
David S. Miller, linux-kernel, Paolo Abeni, Rob Herring, netdev,
Bjorn Andersson, Kalle Valo, Andy Gross, Marijn Suijten,
linux-arm-msm, Jakub Kicinski, ath10k
On 6.04.2023 14:47, Rob Herring wrote:
>
> On Thu, 06 Apr 2023 13:54:04 +0200, Konrad Dybcio wrote:
>> Convert the ATH10K bindings to YAML.
>>
>> Dropped properties that are absent at the current state of mainline:
>> - qcom,msi_addr
>> - qcom,msi_base
>>
>> qcom,coexist-support and qcom,coexist-gpio-pin do very little and should
>> be reconsidered on the driver side, especially the latter one.
>>
>> Somewhat based on the ath11k bindings.
>>
>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>> ---
>> .../bindings/net/wireless/qcom,ath10k.txt | 215 ------------
>> .../bindings/net/wireless/qcom,ath10k.yaml | 359 +++++++++++++++++++++
>> 2 files changed, 359 insertions(+), 215 deletions(-)
>>
>
> My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
> on your patch (DT_CHECKER_FLAGS is new in v5.13):
>
> yamllint warnings/errors:
>
> dtschema/dtc warnings/errors:
> /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.example.dtb: wifi@18800000: wifi-firmware: 'wifi-firmware' does not match any of the regexes: 'pinctrl-[0-9]+'
> From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml
> /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.example.dtb: wifi@18800000: wifi-firmware: 'iommus' is a required property
> From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml
>
> doc reference errors (make refcheckdocs):
> MAINTAINERS: Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
>
> See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230406-topic-ath10k_bindings-v2-1-557f884a65d1@linaro.org
Oh, CHECK_DTBS=1 doesn't run dt_binding_check and I didn't run that
explicitly before resending.. my bad..
Konrad
>
> The base for the series is generally the latest rc1. A different dependency
> should be noted in *this* patch.
>
> If you already ran 'make dt_binding_check' and didn't see the above
> error(s), then make sure 'yamllint' is installed and dt-schema is up to
> date:
>
> pip3 install dtschema --upgrade
>
> Please check and re-submit after running the above command yourself. Note
> that DT_SCHEMA_FILES can be set to your schema file to speed up checking
> your schema. However, it must be unset to test all examples with your schema.
>
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2023-04-06 12:53 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-04-06 11:54 [PATCH v2 0/2] ATH10K YAML conversion Konrad Dybcio
2023-04-06 11:54 ` [PATCH v2 1/2] dt-bindings: net: Convert ATH10K to YAML Konrad Dybcio
2023-04-06 12:47 ` Rob Herring
2023-04-06 12:52 ` Konrad Dybcio
2023-04-06 11:54 ` [PATCH v2 2/2] arm64: dts: qcom: sdm845-polaris: Drop inexistent properties Konrad Dybcio
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).