Linux-ARM-MSM Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH v2 0/9] thermal: tsens: Handle critical interrupts
@ 2019-12-03  5:23 Amit Kucheria
  2019-12-03  5:23 ` [PATCH v2 1/9] drivers: thermal: tsens: De-constify struct tsens_features Amit Kucheria
                   ` (8 more replies)
  0 siblings, 9 replies; 10+ messages in thread
From: Amit Kucheria @ 2019-12-03  5:23 UTC (permalink / raw)
  To: linux-kernel, linux-arm-msm, bjorn.andersson, swboyd, sivaa, Andy Gross
  Cc: Amit Kucheria, Daniel Lezcano, devicetree, linux-pm

TSENS IP v2.x supports critical interrupts and v2.3+ adds watchdog support
in case the FSM is stuck. Enable support in the driver.

This series was generated on top of linux-next from 20191202 to capture
const changes for msm8976 that is queued currently.

Changes from v1:
- Make tsens_features non-const to allow run time detection of features
- Pass tsens_sensor around as a const
- Fix a bug to release dev pointer in success path
- Address review comments from Bjorn and Stephen (thanks for the review)
- Add msm8998 and msm8996 DTSI changes for critical interrupts

Amit Kucheria (9):
  drivers: thermal: tsens: De-constify struct tsens_features
  drivers: thermal: tsens: Pass around struct tsens_sensor as a constant
  drivers: thermal: tsens: use simpler variables
  drivers: thermal: tsens: Release device in success path
  drivers: thermal: tsens: Add critical interrupt support
  drivers: thermal: tsens: Add watchdog support
  arm64: dts: sdm845: thermal: Add critical interrupt support
  arm64: dts: msm8996: thermal: Add critical interrupt support
  arm64: dts: msm8998: thermal: Add critical interrupt support

 arch/arm64/boot/dts/qcom/msm8996.dtsi |  10 +-
 arch/arm64/boot/dts/qcom/msm8998.dtsi |  10 +-
 arch/arm64/boot/dts/qcom/sdm845.dtsi  |  10 +-
 drivers/thermal/qcom/tsens-8960.c     |   4 +-
 drivers/thermal/qcom/tsens-common.c   | 188 +++++++++++++++++++++++---
 drivers/thermal/qcom/tsens-v0_1.c     |   6 +-
 drivers/thermal/qcom/tsens-v1.c       |   6 +-
 drivers/thermal/qcom/tsens-v2.c       |  24 +++-
 drivers/thermal/qcom/tsens.c          |  26 +++-
 drivers/thermal/qcom/tsens.h          | 104 ++++++++++++--
 10 files changed, 332 insertions(+), 56 deletions(-)

-- 
2.17.1


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v2 1/9] drivers: thermal: tsens: De-constify struct tsens_features
  2019-12-03  5:23 [PATCH v2 0/9] thermal: tsens: Handle critical interrupts Amit Kucheria
@ 2019-12-03  5:23 ` Amit Kucheria
  2019-12-03  5:23 ` [PATCH v2 2/9] drivers: thermal: tsens: Pass around struct tsens_sensor as a constant Amit Kucheria
                   ` (7 subsequent siblings)
  8 siblings, 0 replies; 10+ messages in thread
From: Amit Kucheria @ 2019-12-03  5:23 UTC (permalink / raw)
  To: linux-kernel, linux-arm-msm, bjorn.andersson, swboyd, sivaa, Andy Gross
  Cc: Daniel Lezcano, Amit Kucheria, linux-pm

struct tsens_features is currently initialized as part of platform data
at compile-time and not modifiable. We now have some usecases in feature
detection across IP versions where it is more flexible to update the
features after probing registers.

Remove const qualifier from tsens_features and the encapsulating
tsens_plat_data.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 drivers/thermal/qcom/tsens-8960.c |  2 +-
 drivers/thermal/qcom/tsens-v0_1.c |  6 +++---
 drivers/thermal/qcom/tsens-v1.c   |  6 +++---
 drivers/thermal/qcom/tsens-v2.c   |  6 +++---
 drivers/thermal/qcom/tsens.h      | 12 ++++++------
 5 files changed, 16 insertions(+), 16 deletions(-)

diff --git a/drivers/thermal/qcom/tsens-8960.c b/drivers/thermal/qcom/tsens-8960.c
index fb77acb8d13b9..a383a57cfbbcb 100644
--- a/drivers/thermal/qcom/tsens-8960.c
+++ b/drivers/thermal/qcom/tsens-8960.c
@@ -279,7 +279,7 @@ static const struct tsens_ops ops_8960 = {
 	.resume		= resume_8960,
 };
 
-const struct tsens_plat_data data_8960 = {
+struct tsens_plat_data data_8960 = {
 	.num_sensors	= 11,
 	.ops		= &ops_8960,
 };
diff --git a/drivers/thermal/qcom/tsens-v0_1.c b/drivers/thermal/qcom/tsens-v0_1.c
index 4b8dd6de02ce4..959a9371d205c 100644
--- a/drivers/thermal/qcom/tsens-v0_1.c
+++ b/drivers/thermal/qcom/tsens-v0_1.c
@@ -327,7 +327,7 @@ static int calibrate_8974(struct tsens_priv *priv)
 
 /* v0.1: 8916, 8974 */
 
-static const struct tsens_features tsens_v0_1_feat = {
+static struct tsens_features tsens_v0_1_feat = {
 	.ver_major	= VER_0_1,
 	.crit_int	= 0,
 	.adc		= 1,
@@ -377,7 +377,7 @@ static const struct tsens_ops ops_8916 = {
 	.get_temp	= get_temp_common,
 };
 
-const struct tsens_plat_data data_8916 = {
+struct tsens_plat_data data_8916 = {
 	.num_sensors	= 5,
 	.ops		= &ops_8916,
 	.hw_ids		= (unsigned int []){0, 1, 2, 4, 5 },
@@ -392,7 +392,7 @@ static const struct tsens_ops ops_8974 = {
 	.get_temp	= get_temp_common,
 };
 
-const struct tsens_plat_data data_8974 = {
+struct tsens_plat_data data_8974 = {
 	.num_sensors	= 11,
 	.ops		= &ops_8974,
 	.feat		= &tsens_v0_1_feat,
diff --git a/drivers/thermal/qcom/tsens-v1.c b/drivers/thermal/qcom/tsens-v1.c
index bd2ddb684a45d..b682a4df00810 100644
--- a/drivers/thermal/qcom/tsens-v1.c
+++ b/drivers/thermal/qcom/tsens-v1.c
@@ -299,7 +299,7 @@ static int calibrate_8976(struct tsens_priv *priv)
 
 /* v1.x: msm8956,8976,qcs404,405 */
 
-static const struct tsens_features tsens_v1_feat = {
+static struct tsens_features tsens_v1_feat = {
 	.ver_major	= VER_1_X,
 	.crit_int	= 0,
 	.adc		= 1,
@@ -368,7 +368,7 @@ static const struct tsens_ops ops_generic_v1 = {
 	.get_temp	= get_temp_tsens_valid,
 };
 
-const struct tsens_plat_data data_tsens_v1 = {
+struct tsens_plat_data data_tsens_v1 = {
 	.ops		= &ops_generic_v1,
 	.feat		= &tsens_v1_feat,
 	.fields	= tsens_v1_regfields,
@@ -381,7 +381,7 @@ static const struct tsens_ops ops_8976 = {
 };
 
 /* Valid for both MSM8956 and MSM8976. Sensor ID 3 is unused. */
-const struct tsens_plat_data data_8976 = {
+struct tsens_plat_data data_8976 = {
 	.num_sensors	= 11,
 	.ops		= &ops_8976,
 	.hw_ids		= (unsigned int[]){0, 1, 2, 4, 5, 6, 7, 8, 9, 10},
diff --git a/drivers/thermal/qcom/tsens-v2.c b/drivers/thermal/qcom/tsens-v2.c
index a4d15e1abfddd..f1c8ec62e69f9 100644
--- a/drivers/thermal/qcom/tsens-v2.c
+++ b/drivers/thermal/qcom/tsens-v2.c
@@ -27,7 +27,7 @@
 
 /* v2.x: 8996, 8998, sdm845 */
 
-static const struct tsens_features tsens_v2_feat = {
+static struct tsens_features tsens_v2_feat = {
 	.ver_major	= VER_2_X,
 	.crit_int	= 1,
 	.adc		= 0,
@@ -81,14 +81,14 @@ static const struct tsens_ops ops_generic_v2 = {
 	.get_temp	= get_temp_tsens_valid,
 };
 
-const struct tsens_plat_data data_tsens_v2 = {
+struct tsens_plat_data data_tsens_v2 = {
 	.ops		= &ops_generic_v2,
 	.feat		= &tsens_v2_feat,
 	.fields	= tsens_v2_regfields,
 };
 
 /* Kept around for backward compatibility with old msm8996.dtsi */
-const struct tsens_plat_data data_8996 = {
+struct tsens_plat_data data_8996 = {
 	.num_sensors	= 13,
 	.ops		= &ops_generic_v2,
 	.feat		= &tsens_v2_feat,
diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
index e24a865fbc34c..be364bf1d5a63 100644
--- a/drivers/thermal/qcom/tsens.h
+++ b/drivers/thermal/qcom/tsens.h
@@ -440,7 +440,7 @@ struct tsens_plat_data {
 	const u32		num_sensors;
 	const struct tsens_ops	*ops;
 	unsigned int		*hw_ids;
-	const struct tsens_features	*feat;
+	struct tsens_features	*feat;
 	const struct reg_field		*fields;
 };
 
@@ -481,7 +481,7 @@ struct tsens_priv {
 
 	struct regmap_field		*rf[MAX_REGFIELDS];
 	struct tsens_context		ctx;
-	const struct tsens_features	*feat;
+	struct tsens_features		*feat;
 	const struct reg_field		*fields;
 	const struct tsens_ops		*ops;
 
@@ -502,15 +502,15 @@ int tsens_set_trips(void *_sensor, int low, int high);
 irqreturn_t tsens_irq_thread(int irq, void *data);
 
 /* TSENS target */
-extern const struct tsens_plat_data data_8960;
+extern struct tsens_plat_data data_8960;
 
 /* TSENS v0.1 targets */
-extern const struct tsens_plat_data data_8916, data_8974;
+extern struct tsens_plat_data data_8916, data_8974;
 
 /* TSENS v1 targets */
-extern const struct tsens_plat_data data_tsens_v1, data_8976;
+extern struct tsens_plat_data data_tsens_v1, data_8976;
 
 /* TSENS v2 targets */
-extern const struct tsens_plat_data data_8996, data_tsens_v2;
+extern struct tsens_plat_data data_8996, data_tsens_v2;
 
 #endif /* __QCOM_TSENS_H__ */
-- 
2.17.1


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v2 2/9] drivers: thermal: tsens: Pass around struct tsens_sensor as a constant
  2019-12-03  5:23 [PATCH v2 0/9] thermal: tsens: Handle critical interrupts Amit Kucheria
  2019-12-03  5:23 ` [PATCH v2 1/9] drivers: thermal: tsens: De-constify struct tsens_features Amit Kucheria
@ 2019-12-03  5:23 ` Amit Kucheria
  2019-12-03  5:23 ` [PATCH v2 3/9] drivers: thermal: tsens: use simpler variables Amit Kucheria
                   ` (6 subsequent siblings)
  8 siblings, 0 replies; 10+ messages in thread
From: Amit Kucheria @ 2019-12-03  5:23 UTC (permalink / raw)
  To: linux-kernel, linux-arm-msm, bjorn.andersson, swboyd, sivaa, Andy Gross
  Cc: Daniel Lezcano, Amit Kucheria, linux-pm

All the sensor data is initialised at init time. Lock it down by passing
it to functions as a constant.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 drivers/thermal/qcom/tsens-8960.c   |  2 +-
 drivers/thermal/qcom/tsens-common.c | 14 +++++++-------
 drivers/thermal/qcom/tsens.h        |  6 +++---
 3 files changed, 11 insertions(+), 11 deletions(-)

diff --git a/drivers/thermal/qcom/tsens-8960.c b/drivers/thermal/qcom/tsens-8960.c
index a383a57cfbbcb..2a28a5af209ec 100644
--- a/drivers/thermal/qcom/tsens-8960.c
+++ b/drivers/thermal/qcom/tsens-8960.c
@@ -245,7 +245,7 @@ static inline int code_to_mdegC(u32 adc_code, const struct tsens_sensor *s)
 	return adc_code * slope + offset;
 }
 
-static int get_temp_8960(struct tsens_sensor *s, int *temp)
+static int get_temp_8960(const struct tsens_sensor *s, int *temp)
 {
 	int ret;
 	u32 code, trdy;
diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
index c8d57ee0a5bb2..c2df30a08b9e4 100644
--- a/drivers/thermal/qcom/tsens-common.c
+++ b/drivers/thermal/qcom/tsens-common.c
@@ -128,7 +128,7 @@ static inline int code_to_degc(u32 adc_code, const struct tsens_sensor *s)
  * Return: Temperature in milliCelsius on success, a negative errno will
  * be returned in error cases
  */
-static int tsens_hw_to_mC(struct tsens_sensor *s, int field)
+static int tsens_hw_to_mC(const struct tsens_sensor *s, int field)
 {
 	struct tsens_priv *priv = s->priv;
 	u32 resolution;
@@ -160,7 +160,7 @@ static int tsens_hw_to_mC(struct tsens_sensor *s, int field)
  *
  * Return: ADC code or temperature in deciCelsius.
  */
-static int tsens_mC_to_hw(struct tsens_sensor *s, int temp)
+static int tsens_mC_to_hw(const struct tsens_sensor *s, int temp)
 {
 	struct tsens_priv *priv = s->priv;
 
@@ -275,7 +275,7 @@ static int tsens_threshold_violated(struct tsens_priv *priv, u32 hw_id,
 }
 
 static int tsens_read_irq_state(struct tsens_priv *priv, u32 hw_id,
-				struct tsens_sensor *s, struct tsens_irq_data *d)
+				const struct tsens_sensor *s, struct tsens_irq_data *d)
 {
 	int ret;
 
@@ -346,10 +346,10 @@ irqreturn_t tsens_irq_thread(int irq, void *data)
 
 	for (i = 0; i < priv->num_sensors; i++) {
 		bool trigger = false;
-		struct tsens_sensor *s = &priv->sensor[i];
+		const struct tsens_sensor *s = &priv->sensor[i];
 		u32 hw_id = s->hw_id;
 
-		if (IS_ERR(priv->sensor[i].tzd))
+		if (IS_ERR(s->tzd))
 			continue;
 		if (!tsens_threshold_violated(priv, hw_id, &d))
 			continue;
@@ -457,7 +457,7 @@ void tsens_disable_irq(struct tsens_priv *priv)
 	regmap_field_write(priv->rf[INT_EN], 0);
 }
 
-int get_temp_tsens_valid(struct tsens_sensor *s, int *temp)
+int get_temp_tsens_valid(const struct tsens_sensor *s, int *temp)
 {
 	struct tsens_priv *priv = s->priv;
 	int hw_id = s->hw_id;
@@ -486,7 +486,7 @@ int get_temp_tsens_valid(struct tsens_sensor *s, int *temp)
 	return 0;
 }
 
-int get_temp_common(struct tsens_sensor *s, int *temp)
+int get_temp_common(const struct tsens_sensor *s, int *temp)
 {
 	struct tsens_priv *priv = s->priv;
 	int hw_id = s->hw_id;
diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
index be364bf1d5a63..70dc34c805377 100644
--- a/drivers/thermal/qcom/tsens.h
+++ b/drivers/thermal/qcom/tsens.h
@@ -67,7 +67,7 @@ struct tsens_ops {
 	/* mandatory callbacks */
 	int (*init)(struct tsens_priv *priv);
 	int (*calibrate)(struct tsens_priv *priv);
-	int (*get_temp)(struct tsens_sensor *s, int *temp);
+	int (*get_temp)(const struct tsens_sensor *s, int *temp);
 	/* optional callbacks */
 	int (*enable)(struct tsens_priv *priv, int i);
 	void (*disable)(struct tsens_priv *priv);
@@ -494,8 +494,8 @@ struct tsens_priv {
 char *qfprom_read(struct device *dev, const char *cname);
 void compute_intercept_slope(struct tsens_priv *priv, u32 *pt1, u32 *pt2, u32 mode);
 int init_common(struct tsens_priv *priv);
-int get_temp_tsens_valid(struct tsens_sensor *s, int *temp);
-int get_temp_common(struct tsens_sensor *s, int *temp);
+int get_temp_tsens_valid(const struct tsens_sensor *s, int *temp);
+int get_temp_common(const struct tsens_sensor *s, int *temp);
 int tsens_enable_irq(struct tsens_priv *priv);
 void tsens_disable_irq(struct tsens_priv *priv);
 int tsens_set_trips(void *_sensor, int low, int high);
-- 
2.17.1


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v2 3/9] drivers: thermal: tsens: use simpler variables
  2019-12-03  5:23 [PATCH v2 0/9] thermal: tsens: Handle critical interrupts Amit Kucheria
  2019-12-03  5:23 ` [PATCH v2 1/9] drivers: thermal: tsens: De-constify struct tsens_features Amit Kucheria
  2019-12-03  5:23 ` [PATCH v2 2/9] drivers: thermal: tsens: Pass around struct tsens_sensor as a constant Amit Kucheria
@ 2019-12-03  5:23 ` Amit Kucheria
  2019-12-03  5:23 ` [PATCH v2 4/9] drivers: thermal: tsens: Release device in success path Amit Kucheria
                   ` (5 subsequent siblings)
  8 siblings, 0 replies; 10+ messages in thread
From: Amit Kucheria @ 2019-12-03  5:23 UTC (permalink / raw)
  To: linux-kernel, linux-arm-msm, bjorn.andersson, swboyd, sivaa, Andy Gross
  Cc: Daniel Lezcano, Amit Kucheria, linux-pm

We already dereference the sensor and save it into a variable. Use the
variable directly to make the code easier to read.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 drivers/thermal/qcom/tsens-common.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
index c2df30a08b9e4..1cbc5a6e5b4fd 100644
--- a/drivers/thermal/qcom/tsens-common.c
+++ b/drivers/thermal/qcom/tsens-common.c
@@ -368,7 +368,7 @@ irqreturn_t tsens_irq_thread(int irq, void *data)
 			tsens_set_interrupt(priv, hw_id, UPPER, disable);
 			if (d.up_thresh > temp) {
 				dev_dbg(priv->dev, "[%u] %s: re-arm upper\n",
-					priv->sensor[i].hw_id, __func__);
+					hw_id, __func__);
 				tsens_set_interrupt(priv, hw_id, UPPER, enable);
 			} else {
 				trigger = true;
@@ -379,7 +379,7 @@ irqreturn_t tsens_irq_thread(int irq, void *data)
 			tsens_set_interrupt(priv, hw_id, LOWER, disable);
 			if (d.low_thresh < temp) {
 				dev_dbg(priv->dev, "[%u] %s: re-arm low\n",
-					priv->sensor[i].hw_id, __func__);
+					hw_id, __func__);
 				tsens_set_interrupt(priv, hw_id, LOWER, enable);
 			} else {
 				trigger = true;
@@ -392,7 +392,7 @@ irqreturn_t tsens_irq_thread(int irq, void *data)
 		if (trigger) {
 			dev_dbg(priv->dev, "[%u] %s: TZ update trigger (%d mC)\n",
 				hw_id, __func__, temp);
-			thermal_zone_device_update(priv->sensor[i].tzd,
+			thermal_zone_device_update(s->tzd,
 						   THERMAL_EVENT_UNSPECIFIED);
 		} else {
 			dev_dbg(priv->dev, "[%u] %s: no violation:  %d\n",
@@ -435,7 +435,7 @@ int tsens_set_trips(void *_sensor, int low, int high)
 	spin_unlock_irqrestore(&priv->ul_lock, flags);
 
 	dev_dbg(dev, "[%u] %s: (%d:%d)->(%d:%d)\n",
-		s->hw_id, __func__, d.low_thresh, d.up_thresh, cl_low, cl_high);
+		hw_id, __func__, d.low_thresh, d.up_thresh, cl_low, cl_high);
 
 	return 0;
 }
-- 
2.17.1


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v2 4/9] drivers: thermal: tsens: Release device in success path
  2019-12-03  5:23 [PATCH v2 0/9] thermal: tsens: Handle critical interrupts Amit Kucheria
                   ` (2 preceding siblings ...)
  2019-12-03  5:23 ` [PATCH v2 3/9] drivers: thermal: tsens: use simpler variables Amit Kucheria
@ 2019-12-03  5:23 ` Amit Kucheria
  2019-12-03  5:23 ` [PATCH v2 5/9] drivers: thermal: tsens: Add critical interrupt support Amit Kucheria
                   ` (4 subsequent siblings)
  8 siblings, 0 replies; 10+ messages in thread
From: Amit Kucheria @ 2019-12-03  5:23 UTC (permalink / raw)
  To: linux-kernel, linux-arm-msm, bjorn.andersson, swboyd, sivaa, Andy Gross
  Cc: Daniel Lezcano, Amit Kucheria, linux-pm

We don't currently call put_device in case of successfully initialising
the device.

Allow control to fall thru so we can use same code to put_device and
return error.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 drivers/thermal/qcom/tsens-common.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
index 1cbc5a6e5b4fd..e84e94a6f1a73 100644
--- a/drivers/thermal/qcom/tsens-common.c
+++ b/drivers/thermal/qcom/tsens-common.c
@@ -687,8 +687,6 @@ int __init init_common(struct tsens_priv *priv)
 	tsens_enable_irq(priv);
 	tsens_debug_init(op);
 
-	return 0;
-
 err_put_device:
 	put_device(&op->dev);
 	return ret;
-- 
2.17.1


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v2 5/9] drivers: thermal: tsens: Add critical interrupt support
  2019-12-03  5:23 [PATCH v2 0/9] thermal: tsens: Handle critical interrupts Amit Kucheria
                   ` (3 preceding siblings ...)
  2019-12-03  5:23 ` [PATCH v2 4/9] drivers: thermal: tsens: Release device in success path Amit Kucheria
@ 2019-12-03  5:23 ` Amit Kucheria
  2019-12-03  5:23 ` [PATCH v2 6/9] drivers: thermal: tsens: Add watchdog support Amit Kucheria
                   ` (3 subsequent siblings)
  8 siblings, 0 replies; 10+ messages in thread
From: Amit Kucheria @ 2019-12-03  5:23 UTC (permalink / raw)
  To: linux-kernel, linux-arm-msm, bjorn.andersson, swboyd, sivaa, Andy Gross
  Cc: Daniel Lezcano, Amit Kucheria, linux-pm

TSENS IP v2.x adds critical threshold interrupt support for each sensor
in addition to the upper/lower threshold interrupt. Add support in the
driver.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 drivers/thermal/qcom/tsens-common.c | 126 ++++++++++++++++++++++++++--
 drivers/thermal/qcom/tsens-v2.c     |   8 +-
 drivers/thermal/qcom/tsens.c        |  26 +++++-
 drivers/thermal/qcom/tsens.h        |  72 ++++++++++++++++
 4 files changed, 221 insertions(+), 11 deletions(-)

diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
index e84e94a6f1a73..4cf550766cf66 100644
--- a/drivers/thermal/qcom/tsens-common.c
+++ b/drivers/thermal/qcom/tsens-common.c
@@ -23,6 +23,10 @@
  * @low_thresh:     lower threshold temperature value
  * @low_irq_mask:   mask register for lower threshold irqs
  * @low_irq_clear:  clear register for lower threshold irqs
+ * @crit_viol:      critical threshold violated
+ * @crit_thresh:    critical threshold temperature value
+ * @crit_irq_mask:  mask register for critical threshold irqs
+ * @crit_irq_clear: clear register for critical threshold irqs
  *
  * Structure containing data about temperature threshold settings and
  * irq status if they were violated.
@@ -36,6 +40,10 @@ struct tsens_irq_data {
 	int low_thresh;
 	u32 low_irq_mask;
 	u32 low_irq_clear;
+	u32 crit_viol;
+	u32 crit_thresh;
+	u32 crit_irq_mask;
+	u32 crit_irq_clear;
 };
 
 char *qfprom_read(struct device *dev, const char *cname)
@@ -189,6 +197,9 @@ static void tsens_set_interrupt_v1(struct tsens_priv *priv, u32 hw_id,
 	case LOWER:
 		index = LOW_INT_CLEAR_0 + hw_id;
 		break;
+	case CRITICAL:
+		/* No critical interrupts before v2 */
+		break;
 	}
 	regmap_field_write(priv->rf[index], enable ? 0 : 1);
 }
@@ -214,6 +225,10 @@ static void tsens_set_interrupt_v2(struct tsens_priv *priv, u32 hw_id,
 		index_mask  = LOW_INT_MASK_0 + hw_id;
 		index_clear = LOW_INT_CLEAR_0 + hw_id;
 		break;
+	case CRITICAL:
+		index_mask  = CRIT_INT_MASK_0 + hw_id;
+		index_clear = CRIT_INT_CLEAR_0 + hw_id;
+		break;
 	}
 
 	if (enable) {
@@ -268,7 +283,14 @@ static int tsens_threshold_violated(struct tsens_priv *priv, u32 hw_id,
 	ret = regmap_field_read(priv->rf[LOWER_STATUS_0 + hw_id], &d->low_viol);
 	if (ret)
 		return ret;
-	if (d->up_viol || d->low_viol)
+
+	if (priv->feat->crit_int) {
+		ret = regmap_field_read(priv->rf[CRITICAL_STATUS_0 + hw_id], &d->crit_viol);
+		if (ret)
+			return ret;
+	}
+
+	if (d->up_viol || d->low_viol || d->crit_viol)
 		return 1;
 
 	return 0;
@@ -292,22 +314,36 @@ static int tsens_read_irq_state(struct tsens_priv *priv, u32 hw_id,
 		ret = regmap_field_read(priv->rf[LOW_INT_MASK_0 + hw_id], &d->low_irq_mask);
 		if (ret)
 			return ret;
+		ret = regmap_field_read(priv->rf[CRIT_INT_CLEAR_0 + hw_id], &d->crit_irq_clear);
+		if (ret)
+			return ret;
+		ret = regmap_field_read(priv->rf[CRIT_INT_MASK_0 + hw_id], &d->crit_irq_mask);
+		if (ret)
+			return ret;
+
+		d->crit_thresh = tsens_hw_to_mC(s, CRIT_THRESH_0 + hw_id);
 	} else {
 		/* No mask register on older TSENS */
 		d->up_irq_mask = 0;
 		d->low_irq_mask = 0;
+		d->crit_irq_clear = 0;
+		d->crit_irq_mask = 0;
+		d->crit_thresh = 0;
 	}
 
 	d->up_thresh  = tsens_hw_to_mC(s, UP_THRESH_0 + hw_id);
 	d->low_thresh = tsens_hw_to_mC(s, LOW_THRESH_0 + hw_id);
 
-	dev_dbg(priv->dev, "[%u] %s%s: status(%u|%u) | clr(%u|%u) | mask(%u|%u)\n",
-		hw_id, __func__, (d->up_viol || d->low_viol) ? "(V)" : "",
-		d->low_viol, d->up_viol, d->low_irq_clear, d->up_irq_clear,
-		d->low_irq_mask, d->up_irq_mask);
-	dev_dbg(priv->dev, "[%u] %s%s: thresh: (%d:%d)\n", hw_id, __func__,
-		(d->up_viol || d->low_viol) ? "(violation)" : "",
-		d->low_thresh, d->up_thresh);
+	dev_dbg(priv->dev, "[%u] %s%s: status(%u|%u|%u) |"
+		" clr(%u|%u|%u) | mask(%u|%u|%u)\n",
+		hw_id, __func__,
+		(d->up_viol || d->low_viol || d->crit_viol) ? "(V)" : "",
+		d->low_viol, d->up_viol, d->crit_viol,
+		d->low_irq_clear, d->up_irq_clear, d->crit_irq_clear,
+		d->low_irq_mask, d->up_irq_mask, d->crit_irq_mask);
+	dev_dbg(priv->dev, "[%u] %s%s: thresh: (%d:%d:%d)\n", hw_id, __func__,
+		(d->up_viol || d->low_viol || d->crit_viol) ? "(V)" : "",
+		d->low_thresh, d->up_thresh, d->crit_thresh);
 
 	return 0;
 }
@@ -321,6 +357,64 @@ static inline u32 masked_irq(u32 hw_id, u32 mask, enum tsens_ver ver)
 	return 0;
 }
 
+/**
+ * tsens_critical_irq_thread - Threaded interrupt handler for critical interrupts
+ * @irq: irq number
+ * @data: tsens controller private data
+ *
+ * Check all sensors to find ones that violated their critical threshold limits.
+ * Clear and then re-enable the interrupt.
+ *
+ * The level-triggered interrupt might deassert if the temperature returned to
+ * within the threshold limits by the time the handler got scheduled. We
+ * consider the irq to have been handled in that case.
+ *
+ * Return: IRQ_HANDLED
+ */
+irqreturn_t tsens_critical_irq_thread(int irq, void *data)
+{
+	struct tsens_priv *priv = data;
+	struct tsens_irq_data d;
+	unsigned long flags;
+	int temp, ret, i;
+
+	for (i = 0; i < priv->num_sensors; i++) {
+		const struct tsens_sensor *s = &priv->sensor[i];
+		u32 hw_id = s->hw_id;
+
+		if (IS_ERR(s->tzd))
+			continue;
+		if (!tsens_threshold_violated(priv, hw_id, &d))
+			continue;
+		ret = get_temp_tsens_valid(s, &temp);
+		if (ret) {
+			dev_err(priv->dev, "[%u] %s: error reading sensor\n", hw_id, __func__);
+			continue;
+		}
+
+		spin_lock_irqsave(&priv->ul_lock, flags);
+
+		tsens_read_irq_state(priv, hw_id, s, &d);
+
+		if (d.crit_viol &&
+		    !masked_irq(hw_id, d.crit_irq_mask, tsens_version(priv))) {
+			tsens_set_interrupt(priv, hw_id, CRITICAL, false);
+			if (d.crit_thresh > temp) {
+				dev_dbg(priv->dev, "[%u] %s: re-arm upper\n",
+					hw_id, __func__);
+			} else {
+				dev_dbg(priv->dev, "[%u] %s: TZ update trigger (%d mC)\n",
+					hw_id, __func__, temp);
+			}
+			tsens_set_interrupt(priv, hw_id, CRITICAL, true);
+		}
+
+		spin_unlock_irqrestore(&priv->crit_lock, flags);
+	}
+
+	return IRQ_HANDLED;
+}
+
 /**
  * tsens_irq_thread - Threaded interrupt handler for uplow interrupts
  * @irq: irq number
@@ -683,6 +777,22 @@ int __init init_common(struct tsens_priv *priv)
 		}
 	}
 
+	if (priv->feat->crit_int) {
+		/* This loop might need changes if enum regfield_ids is reordered */
+		for (j = CRITICAL_STATUS_0; j <= CRIT_THRESH_15; j += 16) {
+			for (i = 0; i < priv->feat->max_sensors; i++) {
+				int idx = j + i;
+
+				priv->rf[idx] = devm_regmap_field_alloc(dev, priv->tm_map,
+									priv->fields[idx]);
+				if (IS_ERR(priv->rf[idx])) {
+					ret = PTR_ERR(priv->rf[idx]);
+					goto err_put_device;
+				}
+			}
+		}
+	}
+
 	spin_lock_init(&priv->ul_lock);
 	tsens_enable_irq(priv);
 	tsens_debug_init(op);
diff --git a/drivers/thermal/qcom/tsens-v2.c b/drivers/thermal/qcom/tsens-v2.c
index f1c8ec62e69f9..ce5ef0055d136 100644
--- a/drivers/thermal/qcom/tsens-v2.c
+++ b/drivers/thermal/qcom/tsens-v2.c
@@ -51,8 +51,9 @@ static const struct reg_field tsens_v2_regfields[MAX_REGFIELDS] = {
 	[INT_EN]  = REG_FIELD(TM_INT_EN_OFF, 0, 2),
 
 	/* TEMPERATURE THRESHOLDS */
-	REG_FIELD_FOR_EACH_SENSOR16(LOW_THRESH, TM_Sn_UPPER_LOWER_THRESHOLD_OFF,  0,  11),
-	REG_FIELD_FOR_EACH_SENSOR16(UP_THRESH,  TM_Sn_UPPER_LOWER_THRESHOLD_OFF, 12,  23),
+	REG_FIELD_FOR_EACH_SENSOR16(LOW_THRESH,  TM_Sn_UPPER_LOWER_THRESHOLD_OFF,  0,  11),
+	REG_FIELD_FOR_EACH_SENSOR16(UP_THRESH,   TM_Sn_UPPER_LOWER_THRESHOLD_OFF, 12,  23),
+	REG_FIELD_FOR_EACH_SENSOR16(CRIT_THRESH, TM_Sn_CRITICAL_THRESHOLD_OFF,     0,  11),
 
 	/* INTERRUPTS [CLEAR/STATUS/MASK] */
 	REG_FIELD_SPLIT_BITS_0_15(LOW_INT_STATUS,  TM_UPPER_LOWER_INT_STATUS_OFF),
@@ -61,6 +62,9 @@ static const struct reg_field tsens_v2_regfields[MAX_REGFIELDS] = {
 	REG_FIELD_SPLIT_BITS_16_31(UP_INT_STATUS,  TM_UPPER_LOWER_INT_STATUS_OFF),
 	REG_FIELD_SPLIT_BITS_16_31(UP_INT_CLEAR,   TM_UPPER_LOWER_INT_CLEAR_OFF),
 	REG_FIELD_SPLIT_BITS_16_31(UP_INT_MASK,    TM_UPPER_LOWER_INT_MASK_OFF),
+	REG_FIELD_SPLIT_BITS_0_15(CRIT_INT_STATUS, TM_CRITICAL_INT_STATUS_OFF),
+	REG_FIELD_SPLIT_BITS_0_15(CRIT_INT_CLEAR,  TM_CRITICAL_INT_CLEAR_OFF),
+	REG_FIELD_SPLIT_BITS_0_15(CRIT_INT_MASK,   TM_CRITICAL_INT_MASK_OFF),
 
 	/* Sn_STATUS */
 	REG_FIELD_FOR_EACH_SENSOR16(LAST_TEMP,       TM_Sn_STATUS_OFF,  0,  11),
diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
index 015e7d2015985..70eae517d31b4 100644
--- a/drivers/thermal/qcom/tsens.c
+++ b/drivers/thermal/qcom/tsens.c
@@ -87,7 +87,7 @@ static const struct thermal_zone_of_device_ops tsens_of_ops = {
 
 static int tsens_register(struct tsens_priv *priv)
 {
-	int i, ret, irq;
+	int i, ret, irq, irq_crit;
 	struct thermal_zone_device *tzd;
 	struct platform_device *pdev;
 
@@ -122,6 +122,30 @@ static int tsens_register(struct tsens_priv *priv)
 		goto err_put_device;
 	}
 
+	if (priv->feat->crit_int) {
+		/* We override ret to 0 i.e. don't return errors
+		 * in this block to allow older DTs to continue working.
+		 */
+
+		irq_crit = platform_get_irq_byname(pdev, "critical");
+		if (irq_crit < 0) {
+			dev_warn(&pdev->dev, "Missing critical irq in DT\n");
+			goto err_crit_int;
+		}
+		ret = devm_request_threaded_irq(&pdev->dev, irq_crit,
+						NULL, tsens_critical_irq_thread,
+						IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+						dev_name(&pdev->dev), priv);
+		if (ret) {
+			dev_warn(&pdev->dev, "Failed to request critical irq\n");
+			ret = 0;
+			goto err_crit_int;
+		}
+
+		enable_irq_wake(irq_crit);
+	}
+
+err_crit_int:
 	enable_irq_wake(irq);
 
 err_put_device:
diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
index 70dc34c805377..05d5f73178683 100644
--- a/drivers/thermal/qcom/tsens.h
+++ b/drivers/thermal/qcom/tsens.h
@@ -23,6 +23,7 @@
 
 struct tsens_priv;
 
+/* IP version numbers in ascending order */
 enum tsens_ver {
 	VER_0_1 = 0,
 	VER_1_X,
@@ -32,6 +33,7 @@ enum tsens_ver {
 enum tsens_irq_type {
 	LOWER,
 	UPPER,
+	CRITICAL,
 };
 
 /**
@@ -374,6 +376,70 @@ enum regfield_ids {
 	CRITICAL_STATUS_13,
 	CRITICAL_STATUS_14,
 	CRITICAL_STATUS_15,
+	CRIT_INT_STATUS_0,	/* CRITICAL interrupt status */
+	CRIT_INT_STATUS_1,
+	CRIT_INT_STATUS_2,
+	CRIT_INT_STATUS_3,
+	CRIT_INT_STATUS_4,
+	CRIT_INT_STATUS_5,
+	CRIT_INT_STATUS_6,
+	CRIT_INT_STATUS_7,
+	CRIT_INT_STATUS_8,
+	CRIT_INT_STATUS_9,
+	CRIT_INT_STATUS_10,
+	CRIT_INT_STATUS_11,
+	CRIT_INT_STATUS_12,
+	CRIT_INT_STATUS_13,
+	CRIT_INT_STATUS_14,
+	CRIT_INT_STATUS_15,
+	CRIT_INT_CLEAR_0,	/* CRITICAL interrupt clear */
+	CRIT_INT_CLEAR_1,
+	CRIT_INT_CLEAR_2,
+	CRIT_INT_CLEAR_3,
+	CRIT_INT_CLEAR_4,
+	CRIT_INT_CLEAR_5,
+	CRIT_INT_CLEAR_6,
+	CRIT_INT_CLEAR_7,
+	CRIT_INT_CLEAR_8,
+	CRIT_INT_CLEAR_9,
+	CRIT_INT_CLEAR_10,
+	CRIT_INT_CLEAR_11,
+	CRIT_INT_CLEAR_12,
+	CRIT_INT_CLEAR_13,
+	CRIT_INT_CLEAR_14,
+	CRIT_INT_CLEAR_15,
+	CRIT_INT_MASK_0,	/* CRITICAL interrupt mask */
+	CRIT_INT_MASK_1,
+	CRIT_INT_MASK_2,
+	CRIT_INT_MASK_3,
+	CRIT_INT_MASK_4,
+	CRIT_INT_MASK_5,
+	CRIT_INT_MASK_6,
+	CRIT_INT_MASK_7,
+	CRIT_INT_MASK_8,
+	CRIT_INT_MASK_9,
+	CRIT_INT_MASK_10,
+	CRIT_INT_MASK_11,
+	CRIT_INT_MASK_12,
+	CRIT_INT_MASK_13,
+	CRIT_INT_MASK_14,
+	CRIT_INT_MASK_15,
+	CRIT_THRESH_0,		/* CRITICAL threshold values */
+	CRIT_THRESH_1,
+	CRIT_THRESH_2,
+	CRIT_THRESH_3,
+	CRIT_THRESH_4,
+	CRIT_THRESH_5,
+	CRIT_THRESH_6,
+	CRIT_THRESH_7,
+	CRIT_THRESH_8,
+	CRIT_THRESH_9,
+	CRIT_THRESH_10,
+	CRIT_THRESH_11,
+	CRIT_THRESH_12,
+	CRIT_THRESH_13,
+	CRIT_THRESH_14,
+	CRIT_THRESH_15,
 	MIN_STATUS_0,		/* MIN threshold violated */
 	MIN_STATUS_1,
 	MIN_STATUS_2,
@@ -460,6 +526,8 @@ struct tsens_context {
  * @srot_map: pointer to SROT register address space
  * @tm_offset: deal with old device trees that don't address TM and SROT
  *             address space separately
+ * @ul_lock: lock while processing upper/lower threshold interrupts
+ * @crit_lock: lock while processing critical threshold interrupts
  * @rf: array of regmap_fields used to store value of the field
  * @ctx: registers to be saved and restored during suspend/resume
  * @feat: features of the IP
@@ -479,6 +547,9 @@ struct tsens_priv {
 	/* lock for upper/lower threshold interrupts */
 	spinlock_t			ul_lock;
 
+	/* lock for critical threshold interrupts */
+	spinlock_t			crit_lock;
+
 	struct regmap_field		*rf[MAX_REGFIELDS];
 	struct tsens_context		ctx;
 	struct tsens_features		*feat;
@@ -500,6 +571,7 @@ int tsens_enable_irq(struct tsens_priv *priv);
 void tsens_disable_irq(struct tsens_priv *priv);
 int tsens_set_trips(void *_sensor, int low, int high);
 irqreturn_t tsens_irq_thread(int irq, void *data);
+irqreturn_t tsens_critical_irq_thread(int irq, void *data);
 
 /* TSENS target */
 extern struct tsens_plat_data data_8960;
-- 
2.17.1


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v2 6/9] drivers: thermal: tsens: Add watchdog support
  2019-12-03  5:23 [PATCH v2 0/9] thermal: tsens: Handle critical interrupts Amit Kucheria
                   ` (4 preceding siblings ...)
  2019-12-03  5:23 ` [PATCH v2 5/9] drivers: thermal: tsens: Add critical interrupt support Amit Kucheria
@ 2019-12-03  5:23 ` Amit Kucheria
  2019-12-03  5:23 ` [PATCH v2 7/9] arm64: dts: sdm845: thermal: Add critical interrupt support Amit Kucheria
                   ` (2 subsequent siblings)
  8 siblings, 0 replies; 10+ messages in thread
From: Amit Kucheria @ 2019-12-03  5:23 UTC (permalink / raw)
  To: linux-kernel, linux-arm-msm, bjorn.andersson, swboyd, sivaa, Andy Gross
  Cc: Daniel Lezcano, Amit Kucheria, linux-pm

TSENS IP v2.3 onwards adds support for a watchdog to detect if the TSENS
HW FSM is stuck. Add support to detect and restart the FSM in the
driver. The watchdog is configured by the bootloader, we just enable the
feature in the kernel.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 drivers/thermal/qcom/tsens-common.c | 38 +++++++++++++++++++++++++++++
 drivers/thermal/qcom/tsens-v2.c     | 10 ++++++++
 drivers/thermal/qcom/tsens.h        | 14 +++++++++++
 3 files changed, 62 insertions(+)

diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
index 4cf550766cf66..ecbc722eb3487 100644
--- a/drivers/thermal/qcom/tsens-common.c
+++ b/drivers/thermal/qcom/tsens-common.c
@@ -377,6 +377,24 @@ irqreturn_t tsens_critical_irq_thread(int irq, void *data)
 	struct tsens_irq_data d;
 	unsigned long flags;
 	int temp, ret, i;
+	u32 wdog_status, wdog_count;
+
+	if (priv->feat->has_watchdog) {
+		/* Watchdog is present only on v2.3+ */
+		ret = regmap_field_read(priv->rf[WDOG_BARK_STATUS], &wdog_status);
+		if (ret)
+			return ret;
+
+		/* Clear WDOG interrupt */
+		regmap_field_write(priv->rf[WDOG_BARK_CLEAR], 1);
+		regmap_field_write(priv->rf[WDOG_BARK_CLEAR], 0);
+
+		ret = regmap_field_read(priv->rf[WDOG_BARK_COUNT], &wdog_count);
+		if (ret)
+			return ret;
+		if (wdog_count)
+			dev_dbg(priv->dev, "%s: watchdog count: %d\n", __func__, wdog_count);
+	}
 
 	for (i = 0; i < priv->num_sensors; i++) {
 		const struct tsens_sensor *s = &priv->sensor[i];
@@ -684,6 +702,7 @@ int __init init_common(struct tsens_priv *priv)
 {
 	void __iomem *tm_base, *srot_base;
 	struct device *dev = priv->dev;
+	u32 ver_minor;
 	struct resource *res;
 	u32 enabled;
 	int ret, i, j;
@@ -733,6 +752,9 @@ int __init init_common(struct tsens_priv *priv)
 			if (IS_ERR(priv->rf[i]))
 				return PTR_ERR(priv->rf[i]);
 		}
+		ret = regmap_field_read(priv->rf[VER_MINOR], &ver_minor);
+		if (ret)
+			goto err_put_device;
 	}
 
 	priv->rf[TSENS_EN] = devm_regmap_field_alloc(dev, priv->srot_map,
@@ -793,6 +815,22 @@ int __init init_common(struct tsens_priv *priv)
 		}
 	}
 
+	if (tsens_version(priv) > VER_1_X &&  ver_minor > 2) {
+		/* Watchdog is present only on v2.3+ */
+		priv->feat->has_watchdog = 1;
+		for (i = WDOG_BARK_STATUS; i <= CC_MON_MASK; i++) {
+			priv->rf[i] = devm_regmap_field_alloc(dev, priv->tm_map,
+							      priv->fields[i]);
+			if (IS_ERR(priv->rf[i])) {
+				ret = PTR_ERR(priv->rf[i]);
+				goto err_put_device;
+			}
+		}
+		/* Enable WDOG and disable cycle completion monitoring */
+		regmap_field_write(priv->rf[WDOG_BARK_MASK], 0);
+		regmap_field_write(priv->rf[CC_MON_MASK], 1);
+	}
+
 	spin_lock_init(&priv->ul_lock);
 	tsens_enable_irq(priv);
 	tsens_debug_init(op);
diff --git a/drivers/thermal/qcom/tsens-v2.c b/drivers/thermal/qcom/tsens-v2.c
index ce5ef0055d136..b293ed32174b5 100644
--- a/drivers/thermal/qcom/tsens-v2.c
+++ b/drivers/thermal/qcom/tsens-v2.c
@@ -24,6 +24,7 @@
 #define TM_Sn_CRITICAL_THRESHOLD_OFF	0x0060
 #define TM_Sn_STATUS_OFF		0x00a0
 #define TM_TRDY_OFF			0x00e4
+#define TM_WDOG_LOG_OFF		0x013c
 
 /* v2.x: 8996, 8998, sdm845 */
 
@@ -66,6 +67,15 @@ static const struct reg_field tsens_v2_regfields[MAX_REGFIELDS] = {
 	REG_FIELD_SPLIT_BITS_0_15(CRIT_INT_CLEAR,  TM_CRITICAL_INT_CLEAR_OFF),
 	REG_FIELD_SPLIT_BITS_0_15(CRIT_INT_MASK,   TM_CRITICAL_INT_MASK_OFF),
 
+	/* WATCHDOG on v2.3 or later */
+	[WDOG_BARK_STATUS] = REG_FIELD(TM_CRITICAL_INT_STATUS_OFF, 31, 31),
+	[WDOG_BARK_CLEAR]  = REG_FIELD(TM_CRITICAL_INT_CLEAR_OFF,  31, 31),
+	[WDOG_BARK_MASK]   = REG_FIELD(TM_CRITICAL_INT_MASK_OFF,   31, 31),
+	[CC_MON_STATUS]    = REG_FIELD(TM_CRITICAL_INT_STATUS_OFF, 30, 30),
+	[CC_MON_CLEAR]     = REG_FIELD(TM_CRITICAL_INT_CLEAR_OFF,  30, 30),
+	[CC_MON_MASK]      = REG_FIELD(TM_CRITICAL_INT_MASK_OFF,   30, 30),
+	[WDOG_BARK_COUNT]  = REG_FIELD(TM_WDOG_LOG_OFF,             0,  7),
+
 	/* Sn_STATUS */
 	REG_FIELD_FOR_EACH_SENSOR16(LAST_TEMP,       TM_Sn_STATUS_OFF,  0,  11),
 	REG_FIELD_FOR_EACH_SENSOR16(VALID,           TM_Sn_STATUS_OFF, 21,  21),
diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
index 05d5f73178683..f93f7509a5a46 100644
--- a/drivers/thermal/qcom/tsens.h
+++ b/drivers/thermal/qcom/tsens.h
@@ -440,6 +440,18 @@ enum regfield_ids {
 	CRIT_THRESH_13,
 	CRIT_THRESH_14,
 	CRIT_THRESH_15,
+
+	/* WATCHDOG */
+	WDOG_BARK_STATUS,
+	WDOG_BARK_CLEAR,
+	WDOG_BARK_MASK,
+	WDOG_BARK_COUNT,
+
+	/* CYCLE COMPLETION MONITOR */
+	CC_MON_STATUS,
+	CC_MON_CLEAR,
+	CC_MON_MASK,
+
 	MIN_STATUS_0,		/* MIN threshold violated */
 	MIN_STATUS_1,
 	MIN_STATUS_2,
@@ -484,6 +496,7 @@ enum regfield_ids {
  * @adc:      do the sensors only output adc code (instead of temperature)?
  * @srot_split: does the IP neatly splits the register space into SROT and TM,
  *              with SROT only being available to secure boot firmware?
+ * @has_watchdog: does this IP support watchdog functionality?
  * @max_sensors: maximum sensors supported by this version of the IP
  */
 struct tsens_features {
@@ -491,6 +504,7 @@ struct tsens_features {
 	unsigned int crit_int:1;
 	unsigned int adc:1;
 	unsigned int srot_split:1;
+	unsigned int has_watchdog:1;
 	unsigned int max_sensors;
 };
 
-- 
2.17.1


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v2 7/9] arm64: dts: sdm845: thermal: Add critical interrupt support
  2019-12-03  5:23 [PATCH v2 0/9] thermal: tsens: Handle critical interrupts Amit Kucheria
                   ` (5 preceding siblings ...)
  2019-12-03  5:23 ` [PATCH v2 6/9] drivers: thermal: tsens: Add watchdog support Amit Kucheria
@ 2019-12-03  5:23 ` Amit Kucheria
  2019-12-03  5:23 ` [PATCH v2 8/9] arm64: dts: msm8996: " Amit Kucheria
  2019-12-03  5:23 ` [PATCH v2 9/9] arm64: dts: msm8998: " Amit Kucheria
  8 siblings, 0 replies; 10+ messages in thread
From: Amit Kucheria @ 2019-12-03  5:23 UTC (permalink / raw)
  To: linux-kernel, linux-arm-msm, bjorn.andersson, swboyd, sivaa, Andy Gross
  Cc: devicetree

Register critical interrupts for each of the two tsens controllers

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Message-Id: <3686bd40c99692feb955e936b608b080e2cb1826.1568624011.git.amit.kucheria@linaro.org>
---
 arch/arm64/boot/dts/qcom/sdm845.dtsi | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index ddb1f23c936fe..8986553cf2eb6 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -2950,8 +2950,9 @@
 			reg = <0 0x0c263000 0 0x1ff>, /* TM */
 			      <0 0x0c222000 0 0x1ff>; /* SROT */
 			#qcom,sensors = <13>;
-			interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow";
+			interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
 			#thermal-sensor-cells = <1>;
 		};
 
@@ -2960,8 +2961,9 @@
 			reg = <0 0x0c265000 0 0x1ff>, /* TM */
 			      <0 0x0c223000 0 0x1ff>; /* SROT */
 			#qcom,sensors = <8>;
-			interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow";
+			interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
 			#thermal-sensor-cells = <1>;
 		};
 
-- 
2.17.1


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v2 8/9] arm64: dts: msm8996: thermal: Add critical interrupt support
  2019-12-03  5:23 [PATCH v2 0/9] thermal: tsens: Handle critical interrupts Amit Kucheria
                   ` (6 preceding siblings ...)
  2019-12-03  5:23 ` [PATCH v2 7/9] arm64: dts: sdm845: thermal: Add critical interrupt support Amit Kucheria
@ 2019-12-03  5:23 ` " Amit Kucheria
  2019-12-03  5:23 ` [PATCH v2 9/9] arm64: dts: msm8998: " Amit Kucheria
  8 siblings, 0 replies; 10+ messages in thread
From: Amit Kucheria @ 2019-12-03  5:23 UTC (permalink / raw)
  To: linux-kernel, linux-arm-msm, bjorn.andersson, swboyd, sivaa, Andy Gross
  Cc: devicetree

Register critical interrupts for each of the two tsens controllers

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 arch/arm64/boot/dts/qcom/msm8996.dtsi | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 4ca2e7b44559c..fec0e50fe4fa3 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -591,8 +591,9 @@
 			reg = <0x4a9000 0x1000>, /* TM */
 			      <0x4a8000 0x1000>; /* SROT */
 			#qcom,sensors = <13>;
-			interrupts = <GIC_SPI 458 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow";
+			interrupts = <GIC_SPI 458 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 445 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
 			#thermal-sensor-cells = <1>;
 		};
 
@@ -601,8 +602,9 @@
 			reg = <0x4ad000 0x1000>, /* TM */
 			      <0x4ac000 0x1000>; /* SROT */
 			#qcom,sensors = <8>;
-			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow";
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 430 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
 			#thermal-sensor-cells = <1>;
 		};
 
-- 
2.17.1


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v2 9/9] arm64: dts: msm8998: thermal: Add critical interrupt support
  2019-12-03  5:23 [PATCH v2 0/9] thermal: tsens: Handle critical interrupts Amit Kucheria
                   ` (7 preceding siblings ...)
  2019-12-03  5:23 ` [PATCH v2 8/9] arm64: dts: msm8996: " Amit Kucheria
@ 2019-12-03  5:23 ` " Amit Kucheria
  8 siblings, 0 replies; 10+ messages in thread
From: Amit Kucheria @ 2019-12-03  5:23 UTC (permalink / raw)
  To: linux-kernel, linux-arm-msm, bjorn.andersson, swboyd, sivaa, Andy Gross
  Cc: devicetree

Register critical interrupts for each of the two tsens controllers

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 arch/arm64/boot/dts/qcom/msm8998.dtsi | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi
index fc7838ea9a010..4b786b8651a90 100644
--- a/arch/arm64/boot/dts/qcom/msm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi
@@ -817,8 +817,9 @@
 			reg = <0x010ab000 0x1000>, /* TM */
 			      <0x010aa000 0x1000>; /* SROT */
 			#qcom,sensors = <14>;
-			interrupts = <GIC_SPI 458 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow";
+			interrupts = <GIC_SPI 458 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 445 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
 			#thermal-sensor-cells = <1>;
 		};
 
@@ -827,8 +828,9 @@
 			reg = <0x010ae000 0x1000>, /* TM */
 			      <0x010ad000 0x1000>; /* SROT */
 			#qcom,sensors = <8>;
-			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow";
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 430 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
 			#thermal-sensor-cells = <1>;
 		};
 
-- 
2.17.1


^ permalink raw reply	[flat|nested] 10+ messages in thread

end of thread, back to index

Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-12-03  5:23 [PATCH v2 0/9] thermal: tsens: Handle critical interrupts Amit Kucheria
2019-12-03  5:23 ` [PATCH v2 1/9] drivers: thermal: tsens: De-constify struct tsens_features Amit Kucheria
2019-12-03  5:23 ` [PATCH v2 2/9] drivers: thermal: tsens: Pass around struct tsens_sensor as a constant Amit Kucheria
2019-12-03  5:23 ` [PATCH v2 3/9] drivers: thermal: tsens: use simpler variables Amit Kucheria
2019-12-03  5:23 ` [PATCH v2 4/9] drivers: thermal: tsens: Release device in success path Amit Kucheria
2019-12-03  5:23 ` [PATCH v2 5/9] drivers: thermal: tsens: Add critical interrupt support Amit Kucheria
2019-12-03  5:23 ` [PATCH v2 6/9] drivers: thermal: tsens: Add watchdog support Amit Kucheria
2019-12-03  5:23 ` [PATCH v2 7/9] arm64: dts: sdm845: thermal: Add critical interrupt support Amit Kucheria
2019-12-03  5:23 ` [PATCH v2 8/9] arm64: dts: msm8996: " Amit Kucheria
2019-12-03  5:23 ` [PATCH v2 9/9] arm64: dts: msm8998: " Amit Kucheria

Linux-ARM-MSM Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-msm/0 linux-arm-msm/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-msm linux-arm-msm/ https://lore.kernel.org/linux-arm-msm \
		linux-arm-msm@vger.kernel.org
	public-inbox-index linux-arm-msm

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-arm-msm


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git