* [PATCH V3 0/7] Add minimal boot support for IPQ9574
@ 2023-01-30 12:55 devi priya
2023-01-30 12:55 ` [PATCH V3 1/7] dt-bindings: Add ipq9574 clock and reset definitions devi priya
` (6 more replies)
0 siblings, 7 replies; 19+ messages in thread
From: devi priya @ 2023-01-30 12:55 UTC (permalink / raw)
To: agross, andersson, konrad.dybcio, robh+dt,
krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij,
catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler,
dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree,
linux-kernel, linux-clk, linux-gpio, linux-arm-kernel
Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav,
quic_arajkuma, quic_anusha, quic_poovendh
The IPQ9574 is Qualcomm's 802.11ax SoC for Routers,
Gateways and Access Points.
This series adds minimal board boot support for ipq9574-al02-c7 board
Posting V3 series, considering the previously posted version as V2
Changes in V3:
- Rebased on linux-next/master
- Dropped the 'dt-bindings: mmc: sdhci-msm: Document the IPQ9574
compatible' since it is already part of the linux-next/master
- Detailed change log is added in the respective patches
- V2 can be found at
https://lore.kernel.org/linux-arm-msm/f81e4605-9111-7f70-abb3-72067d68f8e2@quicinc.com/
devi priya (7):
dt-bindings: Add ipq9574 clock and reset definitions
clk: qcom: Add Global Clock Controller driver for IPQ9574
dt-bindings: pinctrl: qcom: Add support for IPQ9574
pinctrl: qcom: Add IPQ9574 pinctrl driver
dt-bindings: arm: qcom: Add ipq9574 compatible
arm64: dts: qcom: Add ipq9574 SoC and AL02 board support
arm64: defconfig: Enable IPQ9574 SoC base configs
.../devicetree/bindings/arm/qcom.yaml | 7 +
.../bindings/clock/qcom,ipq9574-gcc.yaml | 72 +
.../bindings/pinctrl/qcom,ipq9574-tlmm.yaml | 137 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 78 +
arch/arm64/boot/dts/qcom/ipq9574.dtsi | 285 ++
arch/arm64/configs/defconfig | 2 +
drivers/clk/qcom/Kconfig | 8 +
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/gcc-ipq9574.c | 4302 +++++++++++++++++
drivers/pinctrl/qcom/Kconfig | 11 +
drivers/pinctrl/qcom/Makefile | 1 +
drivers/pinctrl/qcom/pinctrl-ipq9574.c | 861 ++++
include/dt-bindings/clock/qcom,ipq9574-gcc.h | 213 +
include/dt-bindings/reset/qcom,ipq9574-gcc.h | 164 +
15 files changed, 6143 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq9574-tlmm.yaml
create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
create mode 100644 arch/arm64/boot/dts/qcom/ipq9574.dtsi
create mode 100644 drivers/clk/qcom/gcc-ipq9574.c
create mode 100644 drivers/pinctrl/qcom/pinctrl-ipq9574.c
create mode 100644 include/dt-bindings/clock/qcom,ipq9574-gcc.h
create mode 100644 include/dt-bindings/reset/qcom,ipq9574-gcc.h
base-commit: e2f86c02fdc96ca29ced53221a3cbf50aa6f8b49
--
2.17.1
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH V3 1/7] dt-bindings: Add ipq9574 clock and reset definitions 2023-01-30 12:55 [PATCH V3 0/7] Add minimal boot support for IPQ9574 devi priya @ 2023-01-30 12:55 ` devi priya 2023-01-31 18:16 ` Krzysztof Kozlowski ` (2 more replies) 2023-01-30 12:55 ` [PATCH V3 3/7] dt-bindings: pinctrl: qcom: Add support for IPQ9574 devi priya ` (5 subsequent siblings) 6 siblings, 3 replies; 19+ messages in thread From: devi priya @ 2023-01-30 12:55 UTC (permalink / raw) To: agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh Add clock and reset ID definitions for ipq9574 Co-developed-by: Anusha Rao <quic_anusha@quicinc.com> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com> Signed-off-by: devi priya <quic_devipriy@quicinc.com> --- Changes in V3: - Added a separate clock binding for ipq9574 and reverted the changes from qcom,gcc-other.yaml Changes in V2: - Updated subject prefix to match the subsystem - Updated gcc compatible string to match new naming style - Reverted the changes from qcom,gcc.yaml - Added clock and clock-names to qcom,gcc-other.yaml for ipq9574 - Removed the clock macro definitions for unused clocks .../bindings/clock/qcom,ipq9574-gcc.yaml | 72 ++++++ include/dt-bindings/clock/qcom,ipq9574-gcc.h | 213 ++++++++++++++++++ include/dt-bindings/reset/qcom,ipq9574-gcc.h | 164 ++++++++++++++ 3 files changed, 449 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml create mode 100644 include/dt-bindings/clock/qcom,ipq9574-gcc.h create mode 100644 include/dt-bindings/reset/qcom,ipq9574-gcc.h diff --git a/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml b/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml new file mode 100644 index 000000000000..7a98469b197c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/qcom,ipq9574-gcc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Global Clock & Reset Controller on IPQ9574 + +maintainers: + - Stephen Boyd <sboyd@kernel.org> + +description: | + Qualcomm global clock control module provides the clocks, resets and power + domains on IPQ9574 + + See also:: + include/dt-bindings/clock/qcom,ipq9574-gcc.h + include/dt-bindings/reset/qcom,ipq9574-gcc.h + +properties: + compatible: + const: qcom,ipq9574-gcc + + clocks: + items: + - description: Board XO source + - description: Sleep clock source + - description: Bias PLL ubi clock source + - description: PCIE30 PHY0 pipe clock source + - description: PCIE30 PHY1 pipe clock source + - description: PCIE30 PHY2 pipe clock source + - description: PCIE30 PHY3 pipe clock source + - description: USB3 PHY pipe clock source + + clock-names: + items: + - const: xo + - const: sleep_clk + - const: bias_pll_ubi_nc_clk + - const: pcie30_phy0_pipe_clk + - const: pcie30_phy1_pipe_clk + - const: pcie30_phy2_pipe_clk + - const: pcie30_phy3_pipe_clk + - const: usb3phy_0_cc_pipe_clk + +required: + - compatible + - clocks + +allOf: + - $ref: qcom,gcc.yaml# + +unevaluatedProperties: false + +examples: + - | + clock-controller@1800000 { + compatible = "qcom,ipq9574-gcc"; + reg = <0x01800000 0x80000>; + clocks = <&xo_board_clk>, + <&sleep_clk>, + <&bias_pll_ubi_nc_clk>, + <&pcie30_phy0_pipe_clk>, + <&pcie30_phy1_pipe_clk>, + <&pcie30_phy2_pipe_clk>, + <&pcie30_phy3_pipe_clk>, + <&usb3phy_0_cc_pipe_clk>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; +... diff --git a/include/dt-bindings/clock/qcom,ipq9574-gcc.h b/include/dt-bindings/clock/qcom,ipq9574-gcc.h new file mode 100644 index 000000000000..feedfdd5e00a --- /dev/null +++ b/include/dt-bindings/clock/qcom,ipq9574-gcc.h @@ -0,0 +1,213 @@ +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ +/* + * Copyright (c) 2018-2023 The Linux Foundation. All rights reserved. + */ + +#ifndef _DT_BINDINGS_CLOCK_IPQ_GCC_9048_H +#define _DT_BINDINGS_CLOCK_IPQ_GCC_9048_H + +#define GPLL0_MAIN 0 +#define GPLL0 1 +#define GPLL2_MAIN 2 +#define GPLL2 3 +#define GPLL4_MAIN 4 +#define GPLL4 5 +#define GCC_SLEEP_CLK_SRC 6 +#define APSS_AHB_CLK_SRC 7 +#define APSS_AXI_CLK_SRC 8 +#define BLSP1_QUP1_I2C_APPS_CLK_SRC 9 +#define BLSP1_QUP1_SPI_APPS_CLK_SRC 10 +#define BLSP1_QUP2_I2C_APPS_CLK_SRC 11 +#define BLSP1_QUP2_SPI_APPS_CLK_SRC 12 +#define BLSP1_QUP3_I2C_APPS_CLK_SRC 13 +#define BLSP1_QUP3_SPI_APPS_CLK_SRC 14 +#define BLSP1_QUP4_I2C_APPS_CLK_SRC 15 +#define BLSP1_QUP4_SPI_APPS_CLK_SRC 16 +#define BLSP1_QUP5_I2C_APPS_CLK_SRC 17 +#define BLSP1_QUP5_SPI_APPS_CLK_SRC 18 +#define BLSP1_QUP6_I2C_APPS_CLK_SRC 19 +#define BLSP1_QUP6_SPI_APPS_CLK_SRC 20 +#define BLSP1_UART1_APPS_CLK_SRC 21 +#define BLSP1_UART2_APPS_CLK_SRC 22 +#define BLSP1_UART3_APPS_CLK_SRC 23 +#define BLSP1_UART4_APPS_CLK_SRC 24 +#define BLSP1_UART5_APPS_CLK_SRC 25 +#define BLSP1_UART6_APPS_CLK_SRC 26 +#define GCC_APSS_AHB_CLK 27 +#define GCC_APSS_AXI_CLK 28 +#define GCC_BLSP1_QUP1_I2C_APPS_CLK 29 +#define GCC_BLSP1_QUP1_SPI_APPS_CLK 30 +#define GCC_BLSP1_QUP2_I2C_APPS_CLK 31 +#define GCC_BLSP1_QUP2_SPI_APPS_CLK 32 +#define GCC_BLSP1_QUP3_I2C_APPS_CLK 33 +#define GCC_BLSP1_QUP3_SPI_APPS_CLK 34 +#define GCC_BLSP1_QUP4_I2C_APPS_CLK 35 +#define GCC_BLSP1_QUP4_SPI_APPS_CLK 36 +#define GCC_BLSP1_QUP5_I2C_APPS_CLK 37 +#define GCC_BLSP1_QUP5_SPI_APPS_CLK 38 +#define GCC_BLSP1_QUP6_I2C_APPS_CLK 39 +#define GCC_BLSP1_QUP6_SPI_APPS_CLK 40 +#define GCC_BLSP1_UART1_APPS_CLK 41 +#define GCC_BLSP1_UART2_APPS_CLK 42 +#define GCC_BLSP1_UART3_APPS_CLK 43 +#define GCC_BLSP1_UART4_APPS_CLK 44 +#define GCC_BLSP1_UART5_APPS_CLK 45 +#define GCC_BLSP1_UART6_APPS_CLK 46 +#define PCIE0_AXI_M_CLK_SRC 47 +#define GCC_PCIE0_AXI_M_CLK 48 +#define PCIE1_AXI_M_CLK_SRC 49 +#define GCC_PCIE1_AXI_M_CLK 50 +#define PCIE2_AXI_M_CLK_SRC 51 +#define GCC_PCIE2_AXI_M_CLK 52 +#define PCIE3_AXI_M_CLK_SRC 53 +#define GCC_PCIE3_AXI_M_CLK 54 +#define PCIE0_AXI_S_CLK_SRC 55 +#define GCC_PCIE0_AXI_S_BRIDGE_CLK 56 +#define GCC_PCIE0_AXI_S_CLK 57 +#define PCIE1_AXI_S_CLK_SRC 58 +#define GCC_PCIE1_AXI_S_BRIDGE_CLK 59 +#define GCC_PCIE1_AXI_S_CLK 60 +#define PCIE2_AXI_S_CLK_SRC 61 +#define GCC_PCIE2_AXI_S_BRIDGE_CLK 62 +#define GCC_PCIE2_AXI_S_CLK 63 +#define PCIE3_AXI_S_CLK_SRC 64 +#define GCC_PCIE3_AXI_S_BRIDGE_CLK 65 +#define GCC_PCIE3_AXI_S_CLK 66 +#define PCIE0_PIPE_CLK_SRC 67 +#define PCIE1_PIPE_CLK_SRC 68 +#define PCIE2_PIPE_CLK_SRC 69 +#define PCIE3_PIPE_CLK_SRC 70 +#define PCIE_AUX_CLK_SRC 71 +#define GCC_PCIE0_AUX_CLK 72 +#define GCC_PCIE1_AUX_CLK 73 +#define GCC_PCIE2_AUX_CLK 74 +#define GCC_PCIE3_AUX_CLK 75 +#define PCIE0_RCHNG_CLK_SRC 76 +#define GCC_PCIE0_RCHNG_CLK 77 +#define PCIE1_RCHNG_CLK_SRC 78 +#define GCC_PCIE1_RCHNG_CLK 79 +#define PCIE2_RCHNG_CLK_SRC 80 +#define GCC_PCIE2_RCHNG_CLK 81 +#define PCIE3_RCHNG_CLK_SRC 82 +#define GCC_PCIE3_RCHNG_CLK 83 +#define GCC_PCIE0_AHB_CLK 84 +#define GCC_PCIE1_AHB_CLK 85 +#define GCC_PCIE2_AHB_CLK 86 +#define GCC_PCIE3_AHB_CLK 87 +#define USB0_AUX_CLK_SRC 88 +#define GCC_USB0_AUX_CLK 89 +#define USB0_MASTER_CLK_SRC 90 +#define GCC_USB0_MASTER_CLK 91 +#define GCC_SNOC_USB_CLK 92 +#define GCC_ANOC_USB_AXI_CLK 93 +#define USB0_MOCK_UTMI_CLK_SRC 94 +#define USB0_MOCK_UTMI_DIV_CLK_SRC 95 +#define GCC_USB0_MOCK_UTMI_CLK 96 +#define USB0_PIPE_CLK_SRC 97 +#define GCC_USB0_PHY_CFG_AHB_CLK 98 +#define SDCC1_APPS_CLK_SRC 99 +#define GCC_SDCC1_APPS_CLK 100 +#define SDCC1_ICE_CORE_CLK_SRC 101 +#define GCC_SDCC1_ICE_CORE_CLK 102 +#define GCC_SDCC1_AHB_CLK 103 +#define PCNOC_BFDCD_CLK_SRC 104 +#define GCC_NSSCFG_CLK 105 +#define GCC_NSSNOC_NSSCC_CLK 106 +#define GCC_NSSCC_CLK 107 +#define GCC_NSSNOC_PCNOC_1_CLK 108 +#define GCC_QDSS_DAP_AHB_CLK 109 +#define GCC_QDSS_CFG_AHB_CLK 110 +#define GCC_QPIC_AHB_CLK 111 +#define GCC_QPIC_CLK 112 +#define GCC_BLSP1_AHB_CLK 113 +#define GCC_MDIO_AHB_CLK 114 +#define GCC_PRNG_AHB_CLK 115 +#define GCC_UNIPHY0_AHB_CLK 116 +#define GCC_UNIPHY1_AHB_CLK 117 +#define GCC_UNIPHY2_AHB_CLK 118 +#define GCC_CMN_12GPLL_AHB_CLK 119 +#define GCC_CMN_12GPLL_APU_CLK 120 +#define SYSTEM_NOC_BFDCD_CLK_SRC 121 +#define GCC_NSSNOC_SNOC_CLK 122 +#define GCC_NSSNOC_SNOC_1_CLK 123 +#define GCC_QDSS_ETR_USB_CLK 124 +#define WCSS_AHB_CLK_SRC 125 +#define GCC_Q6_AHB_CLK 126 +#define GCC_Q6_AHB_S_CLK 127 +#define GCC_WCSS_ECAHB_CLK 128 +#define GCC_WCSS_ACMT_CLK 129 +#define GCC_SYS_NOC_WCSS_AHB_CLK 130 +#define WCSS_AXI_M_CLK_SRC 131 +#define GCC_ANOC_WCSS_AXI_M_CLK 132 +#define QDSS_AT_CLK_SRC 133 +#define GCC_Q6SS_ATBM_CLK 134 +#define GCC_WCSS_DBG_IFC_ATB_CLK 135 +#define GCC_NSSNOC_ATB_CLK 136 +#define GCC_QDSS_AT_CLK 137 +#define GCC_SYS_NOC_AT_CLK 138 +#define GCC_PCNOC_AT_CLK 139 +#define GCC_USB0_EUD_AT_CLK 140 +#define GCC_QDSS_EUD_AT_CLK 141 +#define QDSS_STM_CLK_SRC 142 +#define GCC_QDSS_STM_CLK 143 +#define GCC_SYS_NOC_QDSS_STM_AXI_CLK 144 +#define QDSS_TRACECLKIN_CLK_SRC 145 +#define GCC_QDSS_TRACECLKIN_CLK 146 +#define QDSS_TSCTR_CLK_SRC 147 +#define GCC_Q6_TSCTR_1TO2_CLK 148 +#define GCC_WCSS_DBG_IFC_NTS_CLK 149 +#define GCC_QDSS_TSCTR_DIV2_CLK 150 +#define GCC_QDSS_TS_CLK 151 +#define GCC_QDSS_TSCTR_DIV4_CLK 152 +#define GCC_NSS_TS_CLK 153 +#define GCC_QDSS_TSCTR_DIV8_CLK 154 +#define GCC_QDSS_TSCTR_DIV16_CLK 155 +#define GCC_Q6SS_PCLKDBG_CLK 156 +#define GCC_Q6SS_TRIG_CLK 157 +#define GCC_WCSS_DBG_IFC_APB_CLK 158 +#define GCC_WCSS_DBG_IFC_DAPBUS_CLK 159 +#define GCC_QDSS_DAP_CLK 160 +#define GCC_QDSS_APB2JTAG_CLK 161 +#define GCC_QDSS_TSCTR_DIV3_CLK 162 +#define QPIC_IO_MACRO_CLK_SRC 163 +#define GCC_QPIC_IO_MACRO_CLK 164 +#define Q6_AXI_CLK_SRC 165 +#define GCC_Q6_AXIM_CLK 166 +#define GCC_WCSS_Q6_TBU_CLK 167 +#define GCC_MEM_NOC_Q6_AXI_CLK 168 +#define Q6_AXIM2_CLK_SRC 169 +#define NSSNOC_MEMNOC_BFDCD_CLK_SRC 170 +#define GCC_NSSNOC_MEMNOC_CLK 171 +#define GCC_NSSNOC_MEM_NOC_1_CLK 172 +#define GCC_NSS_TBU_CLK 173 +#define GCC_MEM_NOC_NSSNOC_CLK 174 +#define LPASS_AXIM_CLK_SRC 175 +#define LPASS_SWAY_CLK_SRC 176 +#define ADSS_PWM_CLK_SRC 177 +#define GCC_ADSS_PWM_CLK 178 +#define GP1_CLK_SRC 179 +#define GP2_CLK_SRC 180 +#define GP3_CLK_SRC 181 +#define DDRSS_SMS_SLOW_CLK_SRC 182 +#define GCC_XO_CLK_SRC 183 +#define GCC_XO_CLK 184 +#define GCC_NSSNOC_QOSGEN_REF_CLK 185 +#define GCC_NSSNOC_TIMEOUT_REF_CLK 186 +#define GCC_XO_DIV4_CLK 187 +#define GCC_UNIPHY0_SYS_CLK 188 +#define GCC_UNIPHY1_SYS_CLK 189 +#define GCC_UNIPHY2_SYS_CLK 190 +#define GCC_CMN_12GPLL_SYS_CLK 191 +#define GCC_NSSNOC_XO_DCD_CLK 192 +#define GCC_Q6SS_BOOT_CLK 193 +#define UNIPHY_SYS_CLK_SRC 194 +#define NSS_TS_CLK_SRC 195 +#define GCC_ANOC_PCIE0_1LANE_M_CLK 196 +#define GCC_ANOC_PCIE1_1LANE_M_CLK 197 +#define GCC_ANOC_PCIE2_2LANE_M_CLK 198 +#define GCC_ANOC_PCIE3_2LANE_M_CLK 199 +#define GCC_SNOC_PCIE0_1LANE_S_CLK 200 +#define GCC_SNOC_PCIE1_1LANE_S_CLK 201 +#define GCC_SNOC_PCIE2_2LANE_S_CLK 202 +#define GCC_SNOC_PCIE3_2LANE_S_CLK 203 +#endif diff --git a/include/dt-bindings/reset/qcom,ipq9574-gcc.h b/include/dt-bindings/reset/qcom,ipq9574-gcc.h new file mode 100644 index 000000000000..a11adbda45ec --- /dev/null +++ b/include/dt-bindings/reset/qcom,ipq9574-gcc.h @@ -0,0 +1,164 @@ +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ +/* + * Copyright (c) 2018-2023, The Linux Foundation. All rights reserved. + */ + +#ifndef _DT_BINDINGS_RESET_IPQ_GCC_9048_H +#define _DT_BINDINGS_RESET_IPQ_GCC_9048_H + +#define GCC_ADSS_BCR 0 +#define GCC_APC0_VOLTAGE_DROOP_DETECTOR_BCR 1 +#define GCC_BLSP1_BCR 2 +#define GCC_BLSP1_QUP1_BCR 3 +#define GCC_BLSP1_QUP2_BCR 4 +#define GCC_BLSP1_QUP3_BCR 5 +#define GCC_BLSP1_QUP4_BCR 6 +#define GCC_BLSP1_QUP5_BCR 7 +#define GCC_BLSP1_QUP6_BCR 8 +#define GCC_BLSP1_UART1_BCR 9 +#define GCC_BLSP1_UART2_BCR 10 +#define GCC_BLSP1_UART3_BCR 11 +#define GCC_BLSP1_UART4_BCR 12 +#define GCC_BLSP1_UART5_BCR 13 +#define GCC_BLSP1_UART6_BCR 14 +#define GCC_BOOT_ROM_BCR 15 +#define GCC_MDIO_BCR 16 +#define GCC_NSS_BCR 17 +#define GCC_NSS_TBU_BCR 18 +#define GCC_PCIE0_BCR 19 +#define GCC_PCIE0_LINK_DOWN_BCR 20 +#define GCC_PCIE0_PHY_BCR 21 +#define GCC_PCIE0PHY_PHY_BCR 22 +#define GCC_PCIE1_BCR 23 +#define GCC_PCIE1_LINK_DOWN_BCR 24 +#define GCC_PCIE1_PHY_BCR 25 +#define GCC_PCIE1PHY_PHY_BCR 26 +#define GCC_PCIE2_BCR 27 +#define GCC_PCIE2_LINK_DOWN_BCR 28 +#define GCC_PCIE2_PHY_BCR 29 +#define GCC_PCIE2PHY_PHY_BCR 30 +#define GCC_PCIE3_BCR 31 +#define GCC_PCIE3_LINK_DOWN_BCR 32 +#define GCC_PCIE3_PHY_BCR 33 +#define GCC_PCIE3PHY_PHY_BCR 34 +#define GCC_PRNG_BCR 35 +#define GCC_QUSB2_0_PHY_BCR 36 +#define GCC_SDCC_BCR 37 +#define GCC_TLMM_BCR 38 +#define GCC_UNIPHY0_BCR 39 +#define GCC_UNIPHY1_BCR 40 +#define GCC_UNIPHY2_BCR 41 +#define GCC_USB0_PHY_BCR 42 +#define GCC_USB3PHY_0_PHY_BCR 43 +#define GCC_USB_BCR 44 +#define GCC_ANOC0_TBU_BCR 45 +#define GCC_ANOC1_TBU_BCR 46 +#define GCC_ANOC_BCR 47 +#define GCC_APSS_TCU_BCR 48 +#define GCC_CMN_BLK_BCR 49 +#define GCC_CMN_BLK_AHB_ARES 50 +#define GCC_CMN_BLK_SYS_ARES 51 +#define GCC_CMN_BLK_APU_ARES 52 +#define GCC_DCC_BCR 53 +#define GCC_DDRSS_BCR 54 +#define GCC_IMEM_BCR 55 +#define GCC_LPASS_BCR 56 +#define GCC_MPM_BCR 57 +#define GCC_MSG_RAM_BCR 58 +#define GCC_NSSNOC_MEMNOC_1_ARES 59 +#define GCC_NSSNOC_PCNOC_1_ARES 60 +#define GCC_NSSNOC_SNOC_1_ARES 61 +#define GCC_NSSNOC_XO_DCD_ARES 62 +#define GCC_NSSNOC_TS_ARES 63 +#define GCC_NSSCC_ARES 64 +#define GCC_NSSNOC_NSSCC_ARES 65 +#define GCC_NSSNOC_ATB_ARES 66 +#define GCC_NSSNOC_MEMNOC_ARES 67 +#define GCC_NSSNOC_QOSGEN_REF_ARES 68 +#define GCC_NSSNOC_SNOC_ARES 69 +#define GCC_NSSNOC_TIMEOUT_REF_ARES 70 +#define GCC_NSS_CFG_ARES 71 +#define GCC_UBI0_DBG_ARES 72 +#define GCC_PCIE0_AHB_ARES 73 +#define GCC_PCIE0_AUX_ARES 74 +#define GCC_PCIE0_AXI_M_ARES 75 +#define GCC_PCIE0_AXI_M_STICKY_ARES 76 +#define GCC_PCIE0_AXI_S_ARES 77 +#define GCC_PCIE0_AXI_S_STICKY_ARES 78 +#define GCC_PCIE0_CORE_STICKY_ARES 79 +#define GCC_PCIE0_PIPE_ARES 80 +#define GCC_PCIE1_AHB_ARES 81 +#define GCC_PCIE1_AUX_ARES 82 +#define GCC_PCIE1_AXI_M_ARES 83 +#define GCC_PCIE1_AXI_M_STICKY_ARES 84 +#define GCC_PCIE1_AXI_S_ARES 85 +#define GCC_PCIE1_AXI_S_STICKY_ARES 86 +#define GCC_PCIE1_CORE_STICKY_ARES 87 +#define GCC_PCIE1_PIPE_ARES 88 +#define GCC_PCIE2_AHB_ARES 89 +#define GCC_PCIE2_AUX_ARES 90 +#define GCC_PCIE2_AXI_M_ARES 91 +#define GCC_PCIE2_AXI_M_STICKY_ARES 92 +#define GCC_PCIE2_AXI_S_ARES 93 +#define GCC_PCIE2_AXI_S_STICKY_ARES 94 +#define GCC_PCIE2_CORE_STICKY_ARES 95 +#define GCC_PCIE2_PIPE_ARES 96 +#define GCC_PCIE3_AHB_ARES 97 +#define GCC_PCIE3_AUX_ARES 98 +#define GCC_PCIE3_AXI_M_ARES 99 +#define GCC_PCIE3_AXI_M_STICKY_ARES 100 +#define GCC_PCIE3_AXI_S_ARES 101 +#define GCC_PCIE3_AXI_S_STICKY_ARES 102 +#define GCC_PCIE3_CORE_STICKY_ARES 103 +#define GCC_PCIE3_PIPE_ARES 104 +#define GCC_PCNOC_BCR 105 +#define GCC_PCNOC_BUS_TIMEOUT0_BCR 106 +#define GCC_PCNOC_BUS_TIMEOUT1_BCR 107 +#define GCC_PCNOC_BUS_TIMEOUT2_BCR 108 +#define GCC_PCNOC_BUS_TIMEOUT3_BCR 109 +#define GCC_PCNOC_BUS_TIMEOUT4_BCR 110 +#define GCC_PCNOC_BUS_TIMEOUT5_BCR 111 +#define GCC_PCNOC_BUS_TIMEOUT6_BCR 112 +#define GCC_PCNOC_BUS_TIMEOUT7_BCR 113 +#define GCC_PCNOC_BUS_TIMEOUT8_BCR 114 +#define GCC_PCNOC_BUS_TIMEOUT9_BCR 115 +#define GCC_PCNOC_TBU_BCR 116 +#define GCC_Q6SS_DBG_ARES 117 +#define GCC_Q6_AHB_ARES 118 +#define GCC_Q6_AHB_S_ARES 119 +#define GCC_Q6_AXIM2_ARES 120 +#define GCC_Q6_AXIM_ARES 121 +#define GCC_QDSS_BCR 122 +#define GCC_QPIC_BCR 123 +#define GCC_QPIC_AHB_ARES 124 +#define GCC_QPIC_ARES 125 +#define GCC_RBCPR_BCR 126 +#define GCC_RBCPR_MX_BCR 127 +#define GCC_SEC_CTRL_BCR 128 +#define GCC_SMMU_CFG_BCR 129 +#define GCC_SNOC_BCR 130 +#define GCC_SPDM_BCR 131 +#define GCC_TME_BCR 132 +#define GCC_UNIPHY0_SYS_RESET 133 +#define GCC_UNIPHY0_AHB_RESET 134 +#define GCC_UNIPHY0_XPCS_RESET 135 +#define GCC_UNIPHY1_SYS_RESET 136 +#define GCC_UNIPHY1_AHB_RESET 137 +#define GCC_UNIPHY1_XPCS_RESET 138 +#define GCC_UNIPHY2_SYS_RESET 139 +#define GCC_UNIPHY2_AHB_RESET 140 +#define GCC_UNIPHY2_XPCS_RESET 141 +#define GCC_USB_MISC_RESET 142 +#define GCC_WCSSAON_RESET 143 +#define GCC_WCSS_ACMT_ARES 144 +#define GCC_WCSS_AHB_S_ARES 145 +#define GCC_WCSS_AXI_M_ARES 146 +#define GCC_WCSS_BCR 147 +#define GCC_WCSS_DBG_ARES 148 +#define GCC_WCSS_DBG_BDG_ARES 149 +#define GCC_WCSS_ECAHB_ARES 150 +#define GCC_WCSS_Q6_BCR 151 +#define GCC_WCSS_Q6_TBU_BCR 152 +#define GCC_TCSR_BCR 153 + +#endif -- 2.17.1 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH V3 1/7] dt-bindings: Add ipq9574 clock and reset definitions 2023-01-30 12:55 ` [PATCH V3 1/7] dt-bindings: Add ipq9574 clock and reset definitions devi priya @ 2023-01-31 18:16 ` Krzysztof Kozlowski 2023-01-31 21:13 ` Stephen Boyd 2023-02-08 23:11 ` Bjorn Andersson 2 siblings, 0 replies; 19+ messages in thread From: Krzysztof Kozlowski @ 2023-01-31 18:16 UTC (permalink / raw) To: devi priya, agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh On 30/01/2023 13:55, devi priya wrote: > Add clock and reset ID definitions for ipq9574 > > Co-developed-by: Anusha Rao <quic_anusha@quicinc.com> > Signed-off-by: Anusha Rao <quic_anusha@quicinc.com> > Signed-off-by: devi priya <quic_devipriy@quicinc.com> > --- Subject prefixes: dt-bindings: clock: > Changes in V3: > - Added a separate clock binding for ipq9574 and reverted the > changes from qcom,gcc-other.yaml > Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Best regards, Krzysztof ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3 1/7] dt-bindings: Add ipq9574 clock and reset definitions 2023-01-30 12:55 ` [PATCH V3 1/7] dt-bindings: Add ipq9574 clock and reset definitions devi priya 2023-01-31 18:16 ` Krzysztof Kozlowski @ 2023-01-31 21:13 ` Stephen Boyd 2023-02-08 23:11 ` Bjorn Andersson 2 siblings, 0 replies; 19+ messages in thread From: Stephen Boyd @ 2023-01-31 21:13 UTC (permalink / raw) To: agross, andersson, arnd, catalin.marinas, devi priya, devicetree, dmitry.baryshkov, konrad.dybcio, krzysztof.kozlowski+dt, linus.walleij, linux-arm-kernel, linux-arm-msm, linux-clk, linux-gpio, linux-kernel, marcel.ziswiler, mturquette, nfraprado, p.zabel, robh+dt, shawnguo, will Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh Quoting devi priya (2023-01-30 04:55:22) > diff --git a/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml b/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml > new file mode 100644 > index 000000000000..7a98469b197c > --- /dev/null > +++ b/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml > @@ -0,0 +1,72 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/clock/qcom,ipq9574-gcc.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Qualcomm Global Clock & Reset Controller on IPQ9574 > + > +maintainers: > + - Stephen Boyd <sboyd@kernel.org> Can you be the maintainer? I don't work for Qualcomm. ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3 1/7] dt-bindings: Add ipq9574 clock and reset definitions 2023-01-30 12:55 ` [PATCH V3 1/7] dt-bindings: Add ipq9574 clock and reset definitions devi priya 2023-01-31 18:16 ` Krzysztof Kozlowski 2023-01-31 21:13 ` Stephen Boyd @ 2023-02-08 23:11 ` Bjorn Andersson 2023-02-13 14:27 ` Devi Priya 2 siblings, 1 reply; 19+ messages in thread From: Bjorn Andersson @ 2023-02-08 23:11 UTC (permalink / raw) To: devi priya Cc: agross, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel, quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh On Mon, Jan 30, 2023 at 06:25:22PM +0530, devi priya wrote: > Add clock and reset ID definitions for ipq9574 > > Co-developed-by: Anusha Rao <quic_anusha@quicinc.com> > Signed-off-by: Anusha Rao <quic_anusha@quicinc.com> > Signed-off-by: devi priya <quic_devipriy@quicinc.com> > --- > Changes in V3: > - Added a separate clock binding for ipq9574 and reverted the > changes from qcom,gcc-other.yaml > > Changes in V2: > - Updated subject prefix to match the subsystem > - Updated gcc compatible string to match new naming style > - Reverted the changes from qcom,gcc.yaml > - Added clock and clock-names to qcom,gcc-other.yaml for ipq9574 > - Removed the clock macro definitions for unused clocks > > .../bindings/clock/qcom,ipq9574-gcc.yaml | 72 ++++++ > include/dt-bindings/clock/qcom,ipq9574-gcc.h | 213 ++++++++++++++++++ > include/dt-bindings/reset/qcom,ipq9574-gcc.h | 164 ++++++++++++++ > 3 files changed, 449 insertions(+) > create mode 100644 Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml > create mode 100644 include/dt-bindings/clock/qcom,ipq9574-gcc.h > create mode 100644 include/dt-bindings/reset/qcom,ipq9574-gcc.h > > diff --git a/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml b/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml > new file mode 100644 > index 000000000000..7a98469b197c > --- /dev/null > +++ b/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml > @@ -0,0 +1,72 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/clock/qcom,ipq9574-gcc.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Qualcomm Global Clock & Reset Controller on IPQ9574 > + > +maintainers: > + - Stephen Boyd <sboyd@kernel.org> I can be maintainer instead... > + > +description: | > + Qualcomm global clock control module provides the clocks, resets and power > + domains on IPQ9574 > + > + See also:: > + include/dt-bindings/clock/qcom,ipq9574-gcc.h > + include/dt-bindings/reset/qcom,ipq9574-gcc.h > + > +properties: > + compatible: > + const: qcom,ipq9574-gcc > + > + clocks: > + items: > + - description: Board XO source > + - description: Sleep clock source > + - description: Bias PLL ubi clock source > + - description: PCIE30 PHY0 pipe clock source > + - description: PCIE30 PHY1 pipe clock source > + - description: PCIE30 PHY2 pipe clock source > + - description: PCIE30 PHY3 pipe clock source > + - description: USB3 PHY pipe clock source > + > + clock-names: > + items: > + - const: xo > + - const: sleep_clk > + - const: bias_pll_ubi_nc_clk > + - const: pcie30_phy0_pipe_clk > + - const: pcie30_phy1_pipe_clk > + - const: pcie30_phy2_pipe_clk > + - const: pcie30_phy3_pipe_clk > + - const: usb3phy_0_cc_pipe_clk "clock-names" gives the impression that the order of clocks can be modified, but we use .index in the driver. So please drop clock-names, just to avoid the possible confusion. Thanks, Bjorn > + > +required: > + - compatible > + - clocks > + > +allOf: > + - $ref: qcom,gcc.yaml# > + > +unevaluatedProperties: false > + > +examples: > + - | > + clock-controller@1800000 { > + compatible = "qcom,ipq9574-gcc"; > + reg = <0x01800000 0x80000>; > + clocks = <&xo_board_clk>, > + <&sleep_clk>, > + <&bias_pll_ubi_nc_clk>, > + <&pcie30_phy0_pipe_clk>, > + <&pcie30_phy1_pipe_clk>, > + <&pcie30_phy2_pipe_clk>, > + <&pcie30_phy3_pipe_clk>, > + <&usb3phy_0_cc_pipe_clk>; > + #clock-cells = <1>; > + #reset-cells = <1>; > + #power-domain-cells = <1>; > + }; > +... > diff --git a/include/dt-bindings/clock/qcom,ipq9574-gcc.h b/include/dt-bindings/clock/qcom,ipq9574-gcc.h > new file mode 100644 > index 000000000000..feedfdd5e00a > --- /dev/null > +++ b/include/dt-bindings/clock/qcom,ipq9574-gcc.h > @@ -0,0 +1,213 @@ > +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ > +/* > + * Copyright (c) 2018-2023 The Linux Foundation. All rights reserved. > + */ > + > +#ifndef _DT_BINDINGS_CLOCK_IPQ_GCC_9048_H > +#define _DT_BINDINGS_CLOCK_IPQ_GCC_9048_H > + > +#define GPLL0_MAIN 0 > +#define GPLL0 1 > +#define GPLL2_MAIN 2 > +#define GPLL2 3 > +#define GPLL4_MAIN 4 > +#define GPLL4 5 > +#define GCC_SLEEP_CLK_SRC 6 > +#define APSS_AHB_CLK_SRC 7 > +#define APSS_AXI_CLK_SRC 8 > +#define BLSP1_QUP1_I2C_APPS_CLK_SRC 9 > +#define BLSP1_QUP1_SPI_APPS_CLK_SRC 10 > +#define BLSP1_QUP2_I2C_APPS_CLK_SRC 11 > +#define BLSP1_QUP2_SPI_APPS_CLK_SRC 12 > +#define BLSP1_QUP3_I2C_APPS_CLK_SRC 13 > +#define BLSP1_QUP3_SPI_APPS_CLK_SRC 14 > +#define BLSP1_QUP4_I2C_APPS_CLK_SRC 15 > +#define BLSP1_QUP4_SPI_APPS_CLK_SRC 16 > +#define BLSP1_QUP5_I2C_APPS_CLK_SRC 17 > +#define BLSP1_QUP5_SPI_APPS_CLK_SRC 18 > +#define BLSP1_QUP6_I2C_APPS_CLK_SRC 19 > +#define BLSP1_QUP6_SPI_APPS_CLK_SRC 20 > +#define BLSP1_UART1_APPS_CLK_SRC 21 > +#define BLSP1_UART2_APPS_CLK_SRC 22 > +#define BLSP1_UART3_APPS_CLK_SRC 23 > +#define BLSP1_UART4_APPS_CLK_SRC 24 > +#define BLSP1_UART5_APPS_CLK_SRC 25 > +#define BLSP1_UART6_APPS_CLK_SRC 26 > +#define GCC_APSS_AHB_CLK 27 > +#define GCC_APSS_AXI_CLK 28 > +#define GCC_BLSP1_QUP1_I2C_APPS_CLK 29 > +#define GCC_BLSP1_QUP1_SPI_APPS_CLK 30 > +#define GCC_BLSP1_QUP2_I2C_APPS_CLK 31 > +#define GCC_BLSP1_QUP2_SPI_APPS_CLK 32 > +#define GCC_BLSP1_QUP3_I2C_APPS_CLK 33 > +#define GCC_BLSP1_QUP3_SPI_APPS_CLK 34 > +#define GCC_BLSP1_QUP4_I2C_APPS_CLK 35 > +#define GCC_BLSP1_QUP4_SPI_APPS_CLK 36 > +#define GCC_BLSP1_QUP5_I2C_APPS_CLK 37 > +#define GCC_BLSP1_QUP5_SPI_APPS_CLK 38 > +#define GCC_BLSP1_QUP6_I2C_APPS_CLK 39 > +#define GCC_BLSP1_QUP6_SPI_APPS_CLK 40 > +#define GCC_BLSP1_UART1_APPS_CLK 41 > +#define GCC_BLSP1_UART2_APPS_CLK 42 > +#define GCC_BLSP1_UART3_APPS_CLK 43 > +#define GCC_BLSP1_UART4_APPS_CLK 44 > +#define GCC_BLSP1_UART5_APPS_CLK 45 > +#define GCC_BLSP1_UART6_APPS_CLK 46 > +#define PCIE0_AXI_M_CLK_SRC 47 > +#define GCC_PCIE0_AXI_M_CLK 48 > +#define PCIE1_AXI_M_CLK_SRC 49 > +#define GCC_PCIE1_AXI_M_CLK 50 > +#define PCIE2_AXI_M_CLK_SRC 51 > +#define GCC_PCIE2_AXI_M_CLK 52 > +#define PCIE3_AXI_M_CLK_SRC 53 > +#define GCC_PCIE3_AXI_M_CLK 54 > +#define PCIE0_AXI_S_CLK_SRC 55 > +#define GCC_PCIE0_AXI_S_BRIDGE_CLK 56 > +#define GCC_PCIE0_AXI_S_CLK 57 > +#define PCIE1_AXI_S_CLK_SRC 58 > +#define GCC_PCIE1_AXI_S_BRIDGE_CLK 59 > +#define GCC_PCIE1_AXI_S_CLK 60 > +#define PCIE2_AXI_S_CLK_SRC 61 > +#define GCC_PCIE2_AXI_S_BRIDGE_CLK 62 > +#define GCC_PCIE2_AXI_S_CLK 63 > +#define PCIE3_AXI_S_CLK_SRC 64 > +#define GCC_PCIE3_AXI_S_BRIDGE_CLK 65 > +#define GCC_PCIE3_AXI_S_CLK 66 > +#define PCIE0_PIPE_CLK_SRC 67 > +#define PCIE1_PIPE_CLK_SRC 68 > +#define PCIE2_PIPE_CLK_SRC 69 > +#define PCIE3_PIPE_CLK_SRC 70 > +#define PCIE_AUX_CLK_SRC 71 > +#define GCC_PCIE0_AUX_CLK 72 > +#define GCC_PCIE1_AUX_CLK 73 > +#define GCC_PCIE2_AUX_CLK 74 > +#define GCC_PCIE3_AUX_CLK 75 > +#define PCIE0_RCHNG_CLK_SRC 76 > +#define GCC_PCIE0_RCHNG_CLK 77 > +#define PCIE1_RCHNG_CLK_SRC 78 > +#define GCC_PCIE1_RCHNG_CLK 79 > +#define PCIE2_RCHNG_CLK_SRC 80 > +#define GCC_PCIE2_RCHNG_CLK 81 > +#define PCIE3_RCHNG_CLK_SRC 82 > +#define GCC_PCIE3_RCHNG_CLK 83 > +#define GCC_PCIE0_AHB_CLK 84 > +#define GCC_PCIE1_AHB_CLK 85 > +#define GCC_PCIE2_AHB_CLK 86 > +#define GCC_PCIE3_AHB_CLK 87 > +#define USB0_AUX_CLK_SRC 88 > +#define GCC_USB0_AUX_CLK 89 > +#define USB0_MASTER_CLK_SRC 90 > +#define GCC_USB0_MASTER_CLK 91 > +#define GCC_SNOC_USB_CLK 92 > +#define GCC_ANOC_USB_AXI_CLK 93 > +#define USB0_MOCK_UTMI_CLK_SRC 94 > +#define USB0_MOCK_UTMI_DIV_CLK_SRC 95 > +#define GCC_USB0_MOCK_UTMI_CLK 96 > +#define USB0_PIPE_CLK_SRC 97 > +#define GCC_USB0_PHY_CFG_AHB_CLK 98 > +#define SDCC1_APPS_CLK_SRC 99 > +#define GCC_SDCC1_APPS_CLK 100 > +#define SDCC1_ICE_CORE_CLK_SRC 101 > +#define GCC_SDCC1_ICE_CORE_CLK 102 > +#define GCC_SDCC1_AHB_CLK 103 > +#define PCNOC_BFDCD_CLK_SRC 104 > +#define GCC_NSSCFG_CLK 105 > +#define GCC_NSSNOC_NSSCC_CLK 106 > +#define GCC_NSSCC_CLK 107 > +#define GCC_NSSNOC_PCNOC_1_CLK 108 > +#define GCC_QDSS_DAP_AHB_CLK 109 > +#define GCC_QDSS_CFG_AHB_CLK 110 > +#define GCC_QPIC_AHB_CLK 111 > +#define GCC_QPIC_CLK 112 > +#define GCC_BLSP1_AHB_CLK 113 > +#define GCC_MDIO_AHB_CLK 114 > +#define GCC_PRNG_AHB_CLK 115 > +#define GCC_UNIPHY0_AHB_CLK 116 > +#define GCC_UNIPHY1_AHB_CLK 117 > +#define GCC_UNIPHY2_AHB_CLK 118 > +#define GCC_CMN_12GPLL_AHB_CLK 119 > +#define GCC_CMN_12GPLL_APU_CLK 120 > +#define SYSTEM_NOC_BFDCD_CLK_SRC 121 > +#define GCC_NSSNOC_SNOC_CLK 122 > +#define GCC_NSSNOC_SNOC_1_CLK 123 > +#define GCC_QDSS_ETR_USB_CLK 124 > +#define WCSS_AHB_CLK_SRC 125 > +#define GCC_Q6_AHB_CLK 126 > +#define GCC_Q6_AHB_S_CLK 127 > +#define GCC_WCSS_ECAHB_CLK 128 > +#define GCC_WCSS_ACMT_CLK 129 > +#define GCC_SYS_NOC_WCSS_AHB_CLK 130 > +#define WCSS_AXI_M_CLK_SRC 131 > +#define GCC_ANOC_WCSS_AXI_M_CLK 132 > +#define QDSS_AT_CLK_SRC 133 > +#define GCC_Q6SS_ATBM_CLK 134 > +#define GCC_WCSS_DBG_IFC_ATB_CLK 135 > +#define GCC_NSSNOC_ATB_CLK 136 > +#define GCC_QDSS_AT_CLK 137 > +#define GCC_SYS_NOC_AT_CLK 138 > +#define GCC_PCNOC_AT_CLK 139 > +#define GCC_USB0_EUD_AT_CLK 140 > +#define GCC_QDSS_EUD_AT_CLK 141 > +#define QDSS_STM_CLK_SRC 142 > +#define GCC_QDSS_STM_CLK 143 > +#define GCC_SYS_NOC_QDSS_STM_AXI_CLK 144 > +#define QDSS_TRACECLKIN_CLK_SRC 145 > +#define GCC_QDSS_TRACECLKIN_CLK 146 > +#define QDSS_TSCTR_CLK_SRC 147 > +#define GCC_Q6_TSCTR_1TO2_CLK 148 > +#define GCC_WCSS_DBG_IFC_NTS_CLK 149 > +#define GCC_QDSS_TSCTR_DIV2_CLK 150 > +#define GCC_QDSS_TS_CLK 151 > +#define GCC_QDSS_TSCTR_DIV4_CLK 152 > +#define GCC_NSS_TS_CLK 153 > +#define GCC_QDSS_TSCTR_DIV8_CLK 154 > +#define GCC_QDSS_TSCTR_DIV16_CLK 155 > +#define GCC_Q6SS_PCLKDBG_CLK 156 > +#define GCC_Q6SS_TRIG_CLK 157 > +#define GCC_WCSS_DBG_IFC_APB_CLK 158 > +#define GCC_WCSS_DBG_IFC_DAPBUS_CLK 159 > +#define GCC_QDSS_DAP_CLK 160 > +#define GCC_QDSS_APB2JTAG_CLK 161 > +#define GCC_QDSS_TSCTR_DIV3_CLK 162 > +#define QPIC_IO_MACRO_CLK_SRC 163 > +#define GCC_QPIC_IO_MACRO_CLK 164 > +#define Q6_AXI_CLK_SRC 165 > +#define GCC_Q6_AXIM_CLK 166 > +#define GCC_WCSS_Q6_TBU_CLK 167 > +#define GCC_MEM_NOC_Q6_AXI_CLK 168 > +#define Q6_AXIM2_CLK_SRC 169 > +#define NSSNOC_MEMNOC_BFDCD_CLK_SRC 170 > +#define GCC_NSSNOC_MEMNOC_CLK 171 > +#define GCC_NSSNOC_MEM_NOC_1_CLK 172 > +#define GCC_NSS_TBU_CLK 173 > +#define GCC_MEM_NOC_NSSNOC_CLK 174 > +#define LPASS_AXIM_CLK_SRC 175 > +#define LPASS_SWAY_CLK_SRC 176 > +#define ADSS_PWM_CLK_SRC 177 > +#define GCC_ADSS_PWM_CLK 178 > +#define GP1_CLK_SRC 179 > +#define GP2_CLK_SRC 180 > +#define GP3_CLK_SRC 181 > +#define DDRSS_SMS_SLOW_CLK_SRC 182 > +#define GCC_XO_CLK_SRC 183 > +#define GCC_XO_CLK 184 > +#define GCC_NSSNOC_QOSGEN_REF_CLK 185 > +#define GCC_NSSNOC_TIMEOUT_REF_CLK 186 > +#define GCC_XO_DIV4_CLK 187 > +#define GCC_UNIPHY0_SYS_CLK 188 > +#define GCC_UNIPHY1_SYS_CLK 189 > +#define GCC_UNIPHY2_SYS_CLK 190 > +#define GCC_CMN_12GPLL_SYS_CLK 191 > +#define GCC_NSSNOC_XO_DCD_CLK 192 > +#define GCC_Q6SS_BOOT_CLK 193 > +#define UNIPHY_SYS_CLK_SRC 194 > +#define NSS_TS_CLK_SRC 195 > +#define GCC_ANOC_PCIE0_1LANE_M_CLK 196 > +#define GCC_ANOC_PCIE1_1LANE_M_CLK 197 > +#define GCC_ANOC_PCIE2_2LANE_M_CLK 198 > +#define GCC_ANOC_PCIE3_2LANE_M_CLK 199 > +#define GCC_SNOC_PCIE0_1LANE_S_CLK 200 > +#define GCC_SNOC_PCIE1_1LANE_S_CLK 201 > +#define GCC_SNOC_PCIE2_2LANE_S_CLK 202 > +#define GCC_SNOC_PCIE3_2LANE_S_CLK 203 > +#endif > diff --git a/include/dt-bindings/reset/qcom,ipq9574-gcc.h b/include/dt-bindings/reset/qcom,ipq9574-gcc.h > new file mode 100644 > index 000000000000..a11adbda45ec > --- /dev/null > +++ b/include/dt-bindings/reset/qcom,ipq9574-gcc.h > @@ -0,0 +1,164 @@ > +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ > +/* > + * Copyright (c) 2018-2023, The Linux Foundation. All rights reserved. > + */ > + > +#ifndef _DT_BINDINGS_RESET_IPQ_GCC_9048_H > +#define _DT_BINDINGS_RESET_IPQ_GCC_9048_H > + > +#define GCC_ADSS_BCR 0 > +#define GCC_APC0_VOLTAGE_DROOP_DETECTOR_BCR 1 > +#define GCC_BLSP1_BCR 2 > +#define GCC_BLSP1_QUP1_BCR 3 > +#define GCC_BLSP1_QUP2_BCR 4 > +#define GCC_BLSP1_QUP3_BCR 5 > +#define GCC_BLSP1_QUP4_BCR 6 > +#define GCC_BLSP1_QUP5_BCR 7 > +#define GCC_BLSP1_QUP6_BCR 8 > +#define GCC_BLSP1_UART1_BCR 9 > +#define GCC_BLSP1_UART2_BCR 10 > +#define GCC_BLSP1_UART3_BCR 11 > +#define GCC_BLSP1_UART4_BCR 12 > +#define GCC_BLSP1_UART5_BCR 13 > +#define GCC_BLSP1_UART6_BCR 14 > +#define GCC_BOOT_ROM_BCR 15 > +#define GCC_MDIO_BCR 16 > +#define GCC_NSS_BCR 17 > +#define GCC_NSS_TBU_BCR 18 > +#define GCC_PCIE0_BCR 19 > +#define GCC_PCIE0_LINK_DOWN_BCR 20 > +#define GCC_PCIE0_PHY_BCR 21 > +#define GCC_PCIE0PHY_PHY_BCR 22 > +#define GCC_PCIE1_BCR 23 > +#define GCC_PCIE1_LINK_DOWN_BCR 24 > +#define GCC_PCIE1_PHY_BCR 25 > +#define GCC_PCIE1PHY_PHY_BCR 26 > +#define GCC_PCIE2_BCR 27 > +#define GCC_PCIE2_LINK_DOWN_BCR 28 > +#define GCC_PCIE2_PHY_BCR 29 > +#define GCC_PCIE2PHY_PHY_BCR 30 > +#define GCC_PCIE3_BCR 31 > +#define GCC_PCIE3_LINK_DOWN_BCR 32 > +#define GCC_PCIE3_PHY_BCR 33 > +#define GCC_PCIE3PHY_PHY_BCR 34 > +#define GCC_PRNG_BCR 35 > +#define GCC_QUSB2_0_PHY_BCR 36 > +#define GCC_SDCC_BCR 37 > +#define GCC_TLMM_BCR 38 > +#define GCC_UNIPHY0_BCR 39 > +#define GCC_UNIPHY1_BCR 40 > +#define GCC_UNIPHY2_BCR 41 > +#define GCC_USB0_PHY_BCR 42 > +#define GCC_USB3PHY_0_PHY_BCR 43 > +#define GCC_USB_BCR 44 > +#define GCC_ANOC0_TBU_BCR 45 > +#define GCC_ANOC1_TBU_BCR 46 > +#define GCC_ANOC_BCR 47 > +#define GCC_APSS_TCU_BCR 48 > +#define GCC_CMN_BLK_BCR 49 > +#define GCC_CMN_BLK_AHB_ARES 50 > +#define GCC_CMN_BLK_SYS_ARES 51 > +#define GCC_CMN_BLK_APU_ARES 52 > +#define GCC_DCC_BCR 53 > +#define GCC_DDRSS_BCR 54 > +#define GCC_IMEM_BCR 55 > +#define GCC_LPASS_BCR 56 > +#define GCC_MPM_BCR 57 > +#define GCC_MSG_RAM_BCR 58 > +#define GCC_NSSNOC_MEMNOC_1_ARES 59 > +#define GCC_NSSNOC_PCNOC_1_ARES 60 > +#define GCC_NSSNOC_SNOC_1_ARES 61 > +#define GCC_NSSNOC_XO_DCD_ARES 62 > +#define GCC_NSSNOC_TS_ARES 63 > +#define GCC_NSSCC_ARES 64 > +#define GCC_NSSNOC_NSSCC_ARES 65 > +#define GCC_NSSNOC_ATB_ARES 66 > +#define GCC_NSSNOC_MEMNOC_ARES 67 > +#define GCC_NSSNOC_QOSGEN_REF_ARES 68 > +#define GCC_NSSNOC_SNOC_ARES 69 > +#define GCC_NSSNOC_TIMEOUT_REF_ARES 70 > +#define GCC_NSS_CFG_ARES 71 > +#define GCC_UBI0_DBG_ARES 72 > +#define GCC_PCIE0_AHB_ARES 73 > +#define GCC_PCIE0_AUX_ARES 74 > +#define GCC_PCIE0_AXI_M_ARES 75 > +#define GCC_PCIE0_AXI_M_STICKY_ARES 76 > +#define GCC_PCIE0_AXI_S_ARES 77 > +#define GCC_PCIE0_AXI_S_STICKY_ARES 78 > +#define GCC_PCIE0_CORE_STICKY_ARES 79 > +#define GCC_PCIE0_PIPE_ARES 80 > +#define GCC_PCIE1_AHB_ARES 81 > +#define GCC_PCIE1_AUX_ARES 82 > +#define GCC_PCIE1_AXI_M_ARES 83 > +#define GCC_PCIE1_AXI_M_STICKY_ARES 84 > +#define GCC_PCIE1_AXI_S_ARES 85 > +#define GCC_PCIE1_AXI_S_STICKY_ARES 86 > +#define GCC_PCIE1_CORE_STICKY_ARES 87 > +#define GCC_PCIE1_PIPE_ARES 88 > +#define GCC_PCIE2_AHB_ARES 89 > +#define GCC_PCIE2_AUX_ARES 90 > +#define GCC_PCIE2_AXI_M_ARES 91 > +#define GCC_PCIE2_AXI_M_STICKY_ARES 92 > +#define GCC_PCIE2_AXI_S_ARES 93 > +#define GCC_PCIE2_AXI_S_STICKY_ARES 94 > +#define GCC_PCIE2_CORE_STICKY_ARES 95 > +#define GCC_PCIE2_PIPE_ARES 96 > +#define GCC_PCIE3_AHB_ARES 97 > +#define GCC_PCIE3_AUX_ARES 98 > +#define GCC_PCIE3_AXI_M_ARES 99 > +#define GCC_PCIE3_AXI_M_STICKY_ARES 100 > +#define GCC_PCIE3_AXI_S_ARES 101 > +#define GCC_PCIE3_AXI_S_STICKY_ARES 102 > +#define GCC_PCIE3_CORE_STICKY_ARES 103 > +#define GCC_PCIE3_PIPE_ARES 104 > +#define GCC_PCNOC_BCR 105 > +#define GCC_PCNOC_BUS_TIMEOUT0_BCR 106 > +#define GCC_PCNOC_BUS_TIMEOUT1_BCR 107 > +#define GCC_PCNOC_BUS_TIMEOUT2_BCR 108 > +#define GCC_PCNOC_BUS_TIMEOUT3_BCR 109 > +#define GCC_PCNOC_BUS_TIMEOUT4_BCR 110 > +#define GCC_PCNOC_BUS_TIMEOUT5_BCR 111 > +#define GCC_PCNOC_BUS_TIMEOUT6_BCR 112 > +#define GCC_PCNOC_BUS_TIMEOUT7_BCR 113 > +#define GCC_PCNOC_BUS_TIMEOUT8_BCR 114 > +#define GCC_PCNOC_BUS_TIMEOUT9_BCR 115 > +#define GCC_PCNOC_TBU_BCR 116 > +#define GCC_Q6SS_DBG_ARES 117 > +#define GCC_Q6_AHB_ARES 118 > +#define GCC_Q6_AHB_S_ARES 119 > +#define GCC_Q6_AXIM2_ARES 120 > +#define GCC_Q6_AXIM_ARES 121 > +#define GCC_QDSS_BCR 122 > +#define GCC_QPIC_BCR 123 > +#define GCC_QPIC_AHB_ARES 124 > +#define GCC_QPIC_ARES 125 > +#define GCC_RBCPR_BCR 126 > +#define GCC_RBCPR_MX_BCR 127 > +#define GCC_SEC_CTRL_BCR 128 > +#define GCC_SMMU_CFG_BCR 129 > +#define GCC_SNOC_BCR 130 > +#define GCC_SPDM_BCR 131 > +#define GCC_TME_BCR 132 > +#define GCC_UNIPHY0_SYS_RESET 133 > +#define GCC_UNIPHY0_AHB_RESET 134 > +#define GCC_UNIPHY0_XPCS_RESET 135 > +#define GCC_UNIPHY1_SYS_RESET 136 > +#define GCC_UNIPHY1_AHB_RESET 137 > +#define GCC_UNIPHY1_XPCS_RESET 138 > +#define GCC_UNIPHY2_SYS_RESET 139 > +#define GCC_UNIPHY2_AHB_RESET 140 > +#define GCC_UNIPHY2_XPCS_RESET 141 > +#define GCC_USB_MISC_RESET 142 > +#define GCC_WCSSAON_RESET 143 > +#define GCC_WCSS_ACMT_ARES 144 > +#define GCC_WCSS_AHB_S_ARES 145 > +#define GCC_WCSS_AXI_M_ARES 146 > +#define GCC_WCSS_BCR 147 > +#define GCC_WCSS_DBG_ARES 148 > +#define GCC_WCSS_DBG_BDG_ARES 149 > +#define GCC_WCSS_ECAHB_ARES 150 > +#define GCC_WCSS_Q6_BCR 151 > +#define GCC_WCSS_Q6_TBU_BCR 152 > +#define GCC_TCSR_BCR 153 > + > +#endif > -- > 2.17.1 > ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3 1/7] dt-bindings: Add ipq9574 clock and reset definitions 2023-02-08 23:11 ` Bjorn Andersson @ 2023-02-13 14:27 ` Devi Priya 2023-02-14 3:14 ` Devi Priya 0 siblings, 1 reply; 19+ messages in thread From: Devi Priya @ 2023-02-13 14:27 UTC (permalink / raw) To: Bjorn Andersson Cc: agross, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel, quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh On 2/9/2023 4:41 AM, Bjorn Andersson wrote: > On Mon, Jan 30, 2023 at 06:25:22PM +0530, devi priya wrote: >> Add clock and reset ID definitions for ipq9574 >> >> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com> >> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com> >> Signed-off-by: devi priya <quic_devipriy@quicinc.com> >> --- >> Changes in V3: >> - Added a separate clock binding for ipq9574 and reverted the >> changes from qcom,gcc-other.yaml >> >> Changes in V2: >> - Updated subject prefix to match the subsystem >> - Updated gcc compatible string to match new naming style >> - Reverted the changes from qcom,gcc.yaml >> - Added clock and clock-names to qcom,gcc-other.yaml for ipq9574 >> - Removed the clock macro definitions for unused clocks >> >> .../bindings/clock/qcom,ipq9574-gcc.yaml | 72 ++++++ >> include/dt-bindings/clock/qcom,ipq9574-gcc.h | 213 ++++++++++++++++++ >> include/dt-bindings/reset/qcom,ipq9574-gcc.h | 164 ++++++++++++++ >> 3 files changed, 449 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml >> create mode 100644 include/dt-bindings/clock/qcom,ipq9574-gcc.h >> create mode 100644 include/dt-bindings/reset/qcom,ipq9574-gcc.h >> >> diff --git a/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml b/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml >> new file mode 100644 >> index 000000000000..7a98469b197c >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml >> @@ -0,0 +1,72 @@ >> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/clock/qcom,ipq9574-gcc.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: Qualcomm Global Clock & Reset Controller on IPQ9574 >> + >> +maintainers: >> + - Stephen Boyd <sboyd@kernel.org> > > I can be maintainer instead... As per Stephen's suggestion in V3, we have added the author as the maintainter in V4 series. Please suggest us if some changes are to be made.. https://lore.kernel.org/linux-arm-kernel/20230201060319.20434-2-quic_devipriy@quicinc.com/ > >> + >> +description: | >> + Qualcomm global clock control module provides the clocks, resets and power >> + domains on IPQ9574 >> + >> + See also:: >> + include/dt-bindings/clock/qcom,ipq9574-gcc.h >> + include/dt-bindings/reset/qcom,ipq9574-gcc.h >> + >> +properties: >> + compatible: >> + const: qcom,ipq9574-gcc >> + >> + clocks: >> + items: >> + - description: Board XO source >> + - description: Sleep clock source >> + - description: Bias PLL ubi clock source >> + - description: PCIE30 PHY0 pipe clock source >> + - description: PCIE30 PHY1 pipe clock source >> + - description: PCIE30 PHY2 pipe clock source >> + - description: PCIE30 PHY3 pipe clock source >> + - description: USB3 PHY pipe clock source >> + >> + clock-names: >> + items: >> + - const: xo >> + - const: sleep_clk >> + - const: bias_pll_ubi_nc_clk >> + - const: pcie30_phy0_pipe_clk >> + - const: pcie30_phy1_pipe_clk >> + - const: pcie30_phy2_pipe_clk >> + - const: pcie30_phy3_pipe_clk >> + - const: usb3phy_0_cc_pipe_clk > > "clock-names" gives the impression that the order of clocks can be > modified, but we use .index in the driver. So please drop clock-names, > just to avoid the possible confusion. > > Thanks, > Bjorn > >> + >> +required: >> + - compatible >> + - clocks >> + >> +allOf: >> + - $ref: qcom,gcc.yaml# >> + >> +unevaluatedProperties: false >> + >> +examples: >> + - | >> + clock-controller@1800000 { >> + compatible = "qcom,ipq9574-gcc"; >> + reg = <0x01800000 0x80000>; >> + clocks = <&xo_board_clk>, >> + <&sleep_clk>, >> + <&bias_pll_ubi_nc_clk>, >> + <&pcie30_phy0_pipe_clk>, >> + <&pcie30_phy1_pipe_clk>, >> + <&pcie30_phy2_pipe_clk>, >> + <&pcie30_phy3_pipe_clk>, >> + <&usb3phy_0_cc_pipe_clk>; >> + #clock-cells = <1>; >> + #reset-cells = <1>; >> + #power-domain-cells = <1>; >> + }; >> +... >> diff --git a/include/dt-bindings/clock/qcom,ipq9574-gcc.h b/include/dt-bindings/clock/qcom,ipq9574-gcc.h >> new file mode 100644 >> index 000000000000..feedfdd5e00a >> --- /dev/null >> +++ b/include/dt-bindings/clock/qcom,ipq9574-gcc.h >> @@ -0,0 +1,213 @@ >> +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ >> +/* >> + * Copyright (c) 2018-2023 The Linux Foundation. All rights reserved. >> + */ >> + >> +#ifndef _DT_BINDINGS_CLOCK_IPQ_GCC_9048_H >> +#define _DT_BINDINGS_CLOCK_IPQ_GCC_9048_H >> + >> +#define GPLL0_MAIN 0 >> +#define GPLL0 1 >> +#define GPLL2_MAIN 2 >> +#define GPLL2 3 >> +#define GPLL4_MAIN 4 >> +#define GPLL4 5 >> +#define GCC_SLEEP_CLK_SRC 6 >> +#define APSS_AHB_CLK_SRC 7 >> +#define APSS_AXI_CLK_SRC 8 >> +#define BLSP1_QUP1_I2C_APPS_CLK_SRC 9 >> +#define BLSP1_QUP1_SPI_APPS_CLK_SRC 10 >> +#define BLSP1_QUP2_I2C_APPS_CLK_SRC 11 >> +#define BLSP1_QUP2_SPI_APPS_CLK_SRC 12 >> +#define BLSP1_QUP3_I2C_APPS_CLK_SRC 13 >> +#define BLSP1_QUP3_SPI_APPS_CLK_SRC 14 >> +#define BLSP1_QUP4_I2C_APPS_CLK_SRC 15 >> +#define BLSP1_QUP4_SPI_APPS_CLK_SRC 16 >> +#define BLSP1_QUP5_I2C_APPS_CLK_SRC 17 >> +#define BLSP1_QUP5_SPI_APPS_CLK_SRC 18 >> +#define BLSP1_QUP6_I2C_APPS_CLK_SRC 19 >> +#define BLSP1_QUP6_SPI_APPS_CLK_SRC 20 >> +#define BLSP1_UART1_APPS_CLK_SRC 21 >> +#define BLSP1_UART2_APPS_CLK_SRC 22 >> +#define BLSP1_UART3_APPS_CLK_SRC 23 >> +#define BLSP1_UART4_APPS_CLK_SRC 24 >> +#define BLSP1_UART5_APPS_CLK_SRC 25 >> +#define BLSP1_UART6_APPS_CLK_SRC 26 >> +#define GCC_APSS_AHB_CLK 27 >> +#define GCC_APSS_AXI_CLK 28 >> +#define GCC_BLSP1_QUP1_I2C_APPS_CLK 29 >> +#define GCC_BLSP1_QUP1_SPI_APPS_CLK 30 >> +#define GCC_BLSP1_QUP2_I2C_APPS_CLK 31 >> +#define GCC_BLSP1_QUP2_SPI_APPS_CLK 32 >> +#define GCC_BLSP1_QUP3_I2C_APPS_CLK 33 >> +#define GCC_BLSP1_QUP3_SPI_APPS_CLK 34 >> +#define GCC_BLSP1_QUP4_I2C_APPS_CLK 35 >> +#define GCC_BLSP1_QUP4_SPI_APPS_CLK 36 >> +#define GCC_BLSP1_QUP5_I2C_APPS_CLK 37 >> +#define GCC_BLSP1_QUP5_SPI_APPS_CLK 38 >> +#define GCC_BLSP1_QUP6_I2C_APPS_CLK 39 >> +#define GCC_BLSP1_QUP6_SPI_APPS_CLK 40 >> +#define GCC_BLSP1_UART1_APPS_CLK 41 >> +#define GCC_BLSP1_UART2_APPS_CLK 42 >> +#define GCC_BLSP1_UART3_APPS_CLK 43 >> +#define GCC_BLSP1_UART4_APPS_CLK 44 >> +#define GCC_BLSP1_UART5_APPS_CLK 45 >> +#define GCC_BLSP1_UART6_APPS_CLK 46 >> +#define PCIE0_AXI_M_CLK_SRC 47 >> +#define GCC_PCIE0_AXI_M_CLK 48 >> +#define PCIE1_AXI_M_CLK_SRC 49 >> +#define GCC_PCIE1_AXI_M_CLK 50 >> +#define PCIE2_AXI_M_CLK_SRC 51 >> +#define GCC_PCIE2_AXI_M_CLK 52 >> +#define PCIE3_AXI_M_CLK_SRC 53 >> +#define GCC_PCIE3_AXI_M_CLK 54 >> +#define PCIE0_AXI_S_CLK_SRC 55 >> +#define GCC_PCIE0_AXI_S_BRIDGE_CLK 56 >> +#define GCC_PCIE0_AXI_S_CLK 57 >> +#define PCIE1_AXI_S_CLK_SRC 58 >> +#define GCC_PCIE1_AXI_S_BRIDGE_CLK 59 >> +#define GCC_PCIE1_AXI_S_CLK 60 >> +#define PCIE2_AXI_S_CLK_SRC 61 >> +#define GCC_PCIE2_AXI_S_BRIDGE_CLK 62 >> +#define GCC_PCIE2_AXI_S_CLK 63 >> +#define PCIE3_AXI_S_CLK_SRC 64 >> +#define GCC_PCIE3_AXI_S_BRIDGE_CLK 65 >> +#define GCC_PCIE3_AXI_S_CLK 66 >> +#define PCIE0_PIPE_CLK_SRC 67 >> +#define PCIE1_PIPE_CLK_SRC 68 >> +#define PCIE2_PIPE_CLK_SRC 69 >> +#define PCIE3_PIPE_CLK_SRC 70 >> +#define PCIE_AUX_CLK_SRC 71 >> +#define GCC_PCIE0_AUX_CLK 72 >> +#define GCC_PCIE1_AUX_CLK 73 >> +#define GCC_PCIE2_AUX_CLK 74 >> +#define GCC_PCIE3_AUX_CLK 75 >> +#define PCIE0_RCHNG_CLK_SRC 76 >> +#define GCC_PCIE0_RCHNG_CLK 77 >> +#define PCIE1_RCHNG_CLK_SRC 78 >> +#define GCC_PCIE1_RCHNG_CLK 79 >> +#define PCIE2_RCHNG_CLK_SRC 80 >> +#define GCC_PCIE2_RCHNG_CLK 81 >> +#define PCIE3_RCHNG_CLK_SRC 82 >> +#define GCC_PCIE3_RCHNG_CLK 83 >> +#define GCC_PCIE0_AHB_CLK 84 >> +#define GCC_PCIE1_AHB_CLK 85 >> +#define GCC_PCIE2_AHB_CLK 86 >> +#define GCC_PCIE3_AHB_CLK 87 >> +#define USB0_AUX_CLK_SRC 88 >> +#define GCC_USB0_AUX_CLK 89 >> +#define USB0_MASTER_CLK_SRC 90 >> +#define GCC_USB0_MASTER_CLK 91 >> +#define GCC_SNOC_USB_CLK 92 >> +#define GCC_ANOC_USB_AXI_CLK 93 >> +#define USB0_MOCK_UTMI_CLK_SRC 94 >> +#define USB0_MOCK_UTMI_DIV_CLK_SRC 95 >> +#define GCC_USB0_MOCK_UTMI_CLK 96 >> +#define USB0_PIPE_CLK_SRC 97 >> +#define GCC_USB0_PHY_CFG_AHB_CLK 98 >> +#define SDCC1_APPS_CLK_SRC 99 >> +#define GCC_SDCC1_APPS_CLK 100 >> +#define SDCC1_ICE_CORE_CLK_SRC 101 >> +#define GCC_SDCC1_ICE_CORE_CLK 102 >> +#define GCC_SDCC1_AHB_CLK 103 >> +#define PCNOC_BFDCD_CLK_SRC 104 >> +#define GCC_NSSCFG_CLK 105 >> +#define GCC_NSSNOC_NSSCC_CLK 106 >> +#define GCC_NSSCC_CLK 107 >> +#define GCC_NSSNOC_PCNOC_1_CLK 108 >> +#define GCC_QDSS_DAP_AHB_CLK 109 >> +#define GCC_QDSS_CFG_AHB_CLK 110 >> +#define GCC_QPIC_AHB_CLK 111 >> +#define GCC_QPIC_CLK 112 >> +#define GCC_BLSP1_AHB_CLK 113 >> +#define GCC_MDIO_AHB_CLK 114 >> +#define GCC_PRNG_AHB_CLK 115 >> +#define GCC_UNIPHY0_AHB_CLK 116 >> +#define GCC_UNIPHY1_AHB_CLK 117 >> +#define GCC_UNIPHY2_AHB_CLK 118 >> +#define GCC_CMN_12GPLL_AHB_CLK 119 >> +#define GCC_CMN_12GPLL_APU_CLK 120 >> +#define SYSTEM_NOC_BFDCD_CLK_SRC 121 >> +#define GCC_NSSNOC_SNOC_CLK 122 >> +#define GCC_NSSNOC_SNOC_1_CLK 123 >> +#define GCC_QDSS_ETR_USB_CLK 124 >> +#define WCSS_AHB_CLK_SRC 125 >> +#define GCC_Q6_AHB_CLK 126 >> +#define GCC_Q6_AHB_S_CLK 127 >> +#define GCC_WCSS_ECAHB_CLK 128 >> +#define GCC_WCSS_ACMT_CLK 129 >> +#define GCC_SYS_NOC_WCSS_AHB_CLK 130 >> +#define WCSS_AXI_M_CLK_SRC 131 >> +#define GCC_ANOC_WCSS_AXI_M_CLK 132 >> +#define QDSS_AT_CLK_SRC 133 >> +#define GCC_Q6SS_ATBM_CLK 134 >> +#define GCC_WCSS_DBG_IFC_ATB_CLK 135 >> +#define GCC_NSSNOC_ATB_CLK 136 >> +#define GCC_QDSS_AT_CLK 137 >> +#define GCC_SYS_NOC_AT_CLK 138 >> +#define GCC_PCNOC_AT_CLK 139 >> +#define GCC_USB0_EUD_AT_CLK 140 >> +#define GCC_QDSS_EUD_AT_CLK 141 >> +#define QDSS_STM_CLK_SRC 142 >> +#define GCC_QDSS_STM_CLK 143 >> +#define GCC_SYS_NOC_QDSS_STM_AXI_CLK 144 >> +#define QDSS_TRACECLKIN_CLK_SRC 145 >> +#define GCC_QDSS_TRACECLKIN_CLK 146 >> +#define QDSS_TSCTR_CLK_SRC 147 >> +#define GCC_Q6_TSCTR_1TO2_CLK 148 >> +#define GCC_WCSS_DBG_IFC_NTS_CLK 149 >> +#define GCC_QDSS_TSCTR_DIV2_CLK 150 >> +#define GCC_QDSS_TS_CLK 151 >> +#define GCC_QDSS_TSCTR_DIV4_CLK 152 >> +#define GCC_NSS_TS_CLK 153 >> +#define GCC_QDSS_TSCTR_DIV8_CLK 154 >> +#define GCC_QDSS_TSCTR_DIV16_CLK 155 >> +#define GCC_Q6SS_PCLKDBG_CLK 156 >> +#define GCC_Q6SS_TRIG_CLK 157 >> +#define GCC_WCSS_DBG_IFC_APB_CLK 158 >> +#define GCC_WCSS_DBG_IFC_DAPBUS_CLK 159 >> +#define GCC_QDSS_DAP_CLK 160 >> +#define GCC_QDSS_APB2JTAG_CLK 161 >> +#define GCC_QDSS_TSCTR_DIV3_CLK 162 >> +#define QPIC_IO_MACRO_CLK_SRC 163 >> +#define GCC_QPIC_IO_MACRO_CLK 164 >> +#define Q6_AXI_CLK_SRC 165 >> +#define GCC_Q6_AXIM_CLK 166 >> +#define GCC_WCSS_Q6_TBU_CLK 167 >> +#define GCC_MEM_NOC_Q6_AXI_CLK 168 >> +#define Q6_AXIM2_CLK_SRC 169 >> +#define NSSNOC_MEMNOC_BFDCD_CLK_SRC 170 >> +#define GCC_NSSNOC_MEMNOC_CLK 171 >> +#define GCC_NSSNOC_MEM_NOC_1_CLK 172 >> +#define GCC_NSS_TBU_CLK 173 >> +#define GCC_MEM_NOC_NSSNOC_CLK 174 >> +#define LPASS_AXIM_CLK_SRC 175 >> +#define LPASS_SWAY_CLK_SRC 176 >> +#define ADSS_PWM_CLK_SRC 177 >> +#define GCC_ADSS_PWM_CLK 178 >> +#define GP1_CLK_SRC 179 >> +#define GP2_CLK_SRC 180 >> +#define GP3_CLK_SRC 181 >> +#define DDRSS_SMS_SLOW_CLK_SRC 182 >> +#define GCC_XO_CLK_SRC 183 >> +#define GCC_XO_CLK 184 >> +#define GCC_NSSNOC_QOSGEN_REF_CLK 185 >> +#define GCC_NSSNOC_TIMEOUT_REF_CLK 186 >> +#define GCC_XO_DIV4_CLK 187 >> +#define GCC_UNIPHY0_SYS_CLK 188 >> +#define GCC_UNIPHY1_SYS_CLK 189 >> +#define GCC_UNIPHY2_SYS_CLK 190 >> +#define GCC_CMN_12GPLL_SYS_CLK 191 >> +#define GCC_NSSNOC_XO_DCD_CLK 192 >> +#define GCC_Q6SS_BOOT_CLK 193 >> +#define UNIPHY_SYS_CLK_SRC 194 >> +#define NSS_TS_CLK_SRC 195 >> +#define GCC_ANOC_PCIE0_1LANE_M_CLK 196 >> +#define GCC_ANOC_PCIE1_1LANE_M_CLK 197 >> +#define GCC_ANOC_PCIE2_2LANE_M_CLK 198 >> +#define GCC_ANOC_PCIE3_2LANE_M_CLK 199 >> +#define GCC_SNOC_PCIE0_1LANE_S_CLK 200 >> +#define GCC_SNOC_PCIE1_1LANE_S_CLK 201 >> +#define GCC_SNOC_PCIE2_2LANE_S_CLK 202 >> +#define GCC_SNOC_PCIE3_2LANE_S_CLK 203 >> +#endif >> diff --git a/include/dt-bindings/reset/qcom,ipq9574-gcc.h b/include/dt-bindings/reset/qcom,ipq9574-gcc.h >> new file mode 100644 >> index 000000000000..a11adbda45ec >> --- /dev/null >> +++ b/include/dt-bindings/reset/qcom,ipq9574-gcc.h >> @@ -0,0 +1,164 @@ >> +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ >> +/* >> + * Copyright (c) 2018-2023, The Linux Foundation. All rights reserved. >> + */ >> + >> +#ifndef _DT_BINDINGS_RESET_IPQ_GCC_9048_H >> +#define _DT_BINDINGS_RESET_IPQ_GCC_9048_H >> + >> +#define GCC_ADSS_BCR 0 >> +#define GCC_APC0_VOLTAGE_DROOP_DETECTOR_BCR 1 >> +#define GCC_BLSP1_BCR 2 >> +#define GCC_BLSP1_QUP1_BCR 3 >> +#define GCC_BLSP1_QUP2_BCR 4 >> +#define GCC_BLSP1_QUP3_BCR 5 >> +#define GCC_BLSP1_QUP4_BCR 6 >> +#define GCC_BLSP1_QUP5_BCR 7 >> +#define GCC_BLSP1_QUP6_BCR 8 >> +#define GCC_BLSP1_UART1_BCR 9 >> +#define GCC_BLSP1_UART2_BCR 10 >> +#define GCC_BLSP1_UART3_BCR 11 >> +#define GCC_BLSP1_UART4_BCR 12 >> +#define GCC_BLSP1_UART5_BCR 13 >> +#define GCC_BLSP1_UART6_BCR 14 >> +#define GCC_BOOT_ROM_BCR 15 >> +#define GCC_MDIO_BCR 16 >> +#define GCC_NSS_BCR 17 >> +#define GCC_NSS_TBU_BCR 18 >> +#define GCC_PCIE0_BCR 19 >> +#define GCC_PCIE0_LINK_DOWN_BCR 20 >> +#define GCC_PCIE0_PHY_BCR 21 >> +#define GCC_PCIE0PHY_PHY_BCR 22 >> +#define GCC_PCIE1_BCR 23 >> +#define GCC_PCIE1_LINK_DOWN_BCR 24 >> +#define GCC_PCIE1_PHY_BCR 25 >> +#define GCC_PCIE1PHY_PHY_BCR 26 >> +#define GCC_PCIE2_BCR 27 >> +#define GCC_PCIE2_LINK_DOWN_BCR 28 >> +#define GCC_PCIE2_PHY_BCR 29 >> +#define GCC_PCIE2PHY_PHY_BCR 30 >> +#define GCC_PCIE3_BCR 31 >> +#define GCC_PCIE3_LINK_DOWN_BCR 32 >> +#define GCC_PCIE3_PHY_BCR 33 >> +#define GCC_PCIE3PHY_PHY_BCR 34 >> +#define GCC_PRNG_BCR 35 >> +#define GCC_QUSB2_0_PHY_BCR 36 >> +#define GCC_SDCC_BCR 37 >> +#define GCC_TLMM_BCR 38 >> +#define GCC_UNIPHY0_BCR 39 >> +#define GCC_UNIPHY1_BCR 40 >> +#define GCC_UNIPHY2_BCR 41 >> +#define GCC_USB0_PHY_BCR 42 >> +#define GCC_USB3PHY_0_PHY_BCR 43 >> +#define GCC_USB_BCR 44 >> +#define GCC_ANOC0_TBU_BCR 45 >> +#define GCC_ANOC1_TBU_BCR 46 >> +#define GCC_ANOC_BCR 47 >> +#define GCC_APSS_TCU_BCR 48 >> +#define GCC_CMN_BLK_BCR 49 >> +#define GCC_CMN_BLK_AHB_ARES 50 >> +#define GCC_CMN_BLK_SYS_ARES 51 >> +#define GCC_CMN_BLK_APU_ARES 52 >> +#define GCC_DCC_BCR 53 >> +#define GCC_DDRSS_BCR 54 >> +#define GCC_IMEM_BCR 55 >> +#define GCC_LPASS_BCR 56 >> +#define GCC_MPM_BCR 57 >> +#define GCC_MSG_RAM_BCR 58 >> +#define GCC_NSSNOC_MEMNOC_1_ARES 59 >> +#define GCC_NSSNOC_PCNOC_1_ARES 60 >> +#define GCC_NSSNOC_SNOC_1_ARES 61 >> +#define GCC_NSSNOC_XO_DCD_ARES 62 >> +#define GCC_NSSNOC_TS_ARES 63 >> +#define GCC_NSSCC_ARES 64 >> +#define GCC_NSSNOC_NSSCC_ARES 65 >> +#define GCC_NSSNOC_ATB_ARES 66 >> +#define GCC_NSSNOC_MEMNOC_ARES 67 >> +#define GCC_NSSNOC_QOSGEN_REF_ARES 68 >> +#define GCC_NSSNOC_SNOC_ARES 69 >> +#define GCC_NSSNOC_TIMEOUT_REF_ARES 70 >> +#define GCC_NSS_CFG_ARES 71 >> +#define GCC_UBI0_DBG_ARES 72 >> +#define GCC_PCIE0_AHB_ARES 73 >> +#define GCC_PCIE0_AUX_ARES 74 >> +#define GCC_PCIE0_AXI_M_ARES 75 >> +#define GCC_PCIE0_AXI_M_STICKY_ARES 76 >> +#define GCC_PCIE0_AXI_S_ARES 77 >> +#define GCC_PCIE0_AXI_S_STICKY_ARES 78 >> +#define GCC_PCIE0_CORE_STICKY_ARES 79 >> +#define GCC_PCIE0_PIPE_ARES 80 >> +#define GCC_PCIE1_AHB_ARES 81 >> +#define GCC_PCIE1_AUX_ARES 82 >> +#define GCC_PCIE1_AXI_M_ARES 83 >> +#define GCC_PCIE1_AXI_M_STICKY_ARES 84 >> +#define GCC_PCIE1_AXI_S_ARES 85 >> +#define GCC_PCIE1_AXI_S_STICKY_ARES 86 >> +#define GCC_PCIE1_CORE_STICKY_ARES 87 >> +#define GCC_PCIE1_PIPE_ARES 88 >> +#define GCC_PCIE2_AHB_ARES 89 >> +#define GCC_PCIE2_AUX_ARES 90 >> +#define GCC_PCIE2_AXI_M_ARES 91 >> +#define GCC_PCIE2_AXI_M_STICKY_ARES 92 >> +#define GCC_PCIE2_AXI_S_ARES 93 >> +#define GCC_PCIE2_AXI_S_STICKY_ARES 94 >> +#define GCC_PCIE2_CORE_STICKY_ARES 95 >> +#define GCC_PCIE2_PIPE_ARES 96 >> +#define GCC_PCIE3_AHB_ARES 97 >> +#define GCC_PCIE3_AUX_ARES 98 >> +#define GCC_PCIE3_AXI_M_ARES 99 >> +#define GCC_PCIE3_AXI_M_STICKY_ARES 100 >> +#define GCC_PCIE3_AXI_S_ARES 101 >> +#define GCC_PCIE3_AXI_S_STICKY_ARES 102 >> +#define GCC_PCIE3_CORE_STICKY_ARES 103 >> +#define GCC_PCIE3_PIPE_ARES 104 >> +#define GCC_PCNOC_BCR 105 >> +#define GCC_PCNOC_BUS_TIMEOUT0_BCR 106 >> +#define GCC_PCNOC_BUS_TIMEOUT1_BCR 107 >> +#define GCC_PCNOC_BUS_TIMEOUT2_BCR 108 >> +#define GCC_PCNOC_BUS_TIMEOUT3_BCR 109 >> +#define GCC_PCNOC_BUS_TIMEOUT4_BCR 110 >> +#define GCC_PCNOC_BUS_TIMEOUT5_BCR 111 >> +#define GCC_PCNOC_BUS_TIMEOUT6_BCR 112 >> +#define GCC_PCNOC_BUS_TIMEOUT7_BCR 113 >> +#define GCC_PCNOC_BUS_TIMEOUT8_BCR 114 >> +#define GCC_PCNOC_BUS_TIMEOUT9_BCR 115 >> +#define GCC_PCNOC_TBU_BCR 116 >> +#define GCC_Q6SS_DBG_ARES 117 >> +#define GCC_Q6_AHB_ARES 118 >> +#define GCC_Q6_AHB_S_ARES 119 >> +#define GCC_Q6_AXIM2_ARES 120 >> +#define GCC_Q6_AXIM_ARES 121 >> +#define GCC_QDSS_BCR 122 >> +#define GCC_QPIC_BCR 123 >> +#define GCC_QPIC_AHB_ARES 124 >> +#define GCC_QPIC_ARES 125 >> +#define GCC_RBCPR_BCR 126 >> +#define GCC_RBCPR_MX_BCR 127 >> +#define GCC_SEC_CTRL_BCR 128 >> +#define GCC_SMMU_CFG_BCR 129 >> +#define GCC_SNOC_BCR 130 >> +#define GCC_SPDM_BCR 131 >> +#define GCC_TME_BCR 132 >> +#define GCC_UNIPHY0_SYS_RESET 133 >> +#define GCC_UNIPHY0_AHB_RESET 134 >> +#define GCC_UNIPHY0_XPCS_RESET 135 >> +#define GCC_UNIPHY1_SYS_RESET 136 >> +#define GCC_UNIPHY1_AHB_RESET 137 >> +#define GCC_UNIPHY1_XPCS_RESET 138 >> +#define GCC_UNIPHY2_SYS_RESET 139 >> +#define GCC_UNIPHY2_AHB_RESET 140 >> +#define GCC_UNIPHY2_XPCS_RESET 141 >> +#define GCC_USB_MISC_RESET 142 >> +#define GCC_WCSSAON_RESET 143 >> +#define GCC_WCSS_ACMT_ARES 144 >> +#define GCC_WCSS_AHB_S_ARES 145 >> +#define GCC_WCSS_AXI_M_ARES 146 >> +#define GCC_WCSS_BCR 147 >> +#define GCC_WCSS_DBG_ARES 148 >> +#define GCC_WCSS_DBG_BDG_ARES 149 >> +#define GCC_WCSS_ECAHB_ARES 150 >> +#define GCC_WCSS_Q6_BCR 151 >> +#define GCC_WCSS_Q6_TBU_BCR 152 >> +#define GCC_TCSR_BCR 153 >> + >> +#endif >> -- >> 2.17.1 >> ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3 1/7] dt-bindings: Add ipq9574 clock and reset definitions 2023-02-13 14:27 ` Devi Priya @ 2023-02-14 3:14 ` Devi Priya 0 siblings, 0 replies; 19+ messages in thread From: Devi Priya @ 2023-02-14 3:14 UTC (permalink / raw) To: Bjorn Andersson Cc: agross, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel, quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh On 2/13/2023 7:57 PM, Devi Priya wrote: > > > On 2/9/2023 4:41 AM, Bjorn Andersson wrote: >> On Mon, Jan 30, 2023 at 06:25:22PM +0530, devi priya wrote: >>> Add clock and reset ID definitions for ipq9574 >>> >>> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com> >>> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com> >>> Signed-off-by: devi priya <quic_devipriy@quicinc.com> >>> --- >>> Changes in V3: >>> - Added a separate clock binding for ipq9574 and reverted the >>> changes from qcom,gcc-other.yaml >>> >>> Changes in V2: >>> - Updated subject prefix to match the subsystem >>> - Updated gcc compatible string to match new naming style >>> - Reverted the changes from qcom,gcc.yaml >>> - Added clock and clock-names to qcom,gcc-other.yaml for >>> ipq9574 >>> - Removed the clock macro definitions for unused clocks >>> >>> .../bindings/clock/qcom,ipq9574-gcc.yaml | 72 ++++++ >>> include/dt-bindings/clock/qcom,ipq9574-gcc.h | 213 ++++++++++++++++++ >>> include/dt-bindings/reset/qcom,ipq9574-gcc.h | 164 ++++++++++++++ >>> 3 files changed, 449 insertions(+) >>> create mode 100644 >>> Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml >>> create mode 100644 include/dt-bindings/clock/qcom,ipq9574-gcc.h >>> create mode 100644 include/dt-bindings/reset/qcom,ipq9574-gcc.h >>> >>> diff --git >>> a/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml >>> b/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml >>> new file mode 100644 >>> index 000000000000..7a98469b197c >>> --- /dev/null >>> +++ b/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml >>> @@ -0,0 +1,72 @@ >>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) >>> +%YAML 1.2 >>> +--- >>> +$id: http://devicetree.org/schemas/clock/qcom,ipq9574-gcc.yaml# >>> +$schema: http://devicetree.org/meta-schemas/core.yaml# >>> + >>> +title: Qualcomm Global Clock & Reset Controller on IPQ9574 >>> + >>> +maintainers: >>> + - Stephen Boyd <sboyd@kernel.org> >> >> I can be maintainer instead... > As per Stephen's suggestion in V3, we have added the author as the > maintainter in V4 series. Please suggest us if some changes are to be > made.. > https://lore.kernel.org/linux-arm-kernel/20230201060319.20434-2-quic_devipriy@quicinc.com/ >> >>> + >>> +description: | >>> + Qualcomm global clock control module provides the clocks, resets >>> and power >>> + domains on IPQ9574 >>> + >>> + See also:: >>> + include/dt-bindings/clock/qcom,ipq9574-gcc.h >>> + include/dt-bindings/reset/qcom,ipq9574-gcc.h >>> + >>> +properties: >>> + compatible: >>> + const: qcom,ipq9574-gcc >>> + >>> + clocks: >>> + items: >>> + - description: Board XO source >>> + - description: Sleep clock source >>> + - description: Bias PLL ubi clock source >>> + - description: PCIE30 PHY0 pipe clock source >>> + - description: PCIE30 PHY1 pipe clock source >>> + - description: PCIE30 PHY2 pipe clock source >>> + - description: PCIE30 PHY3 pipe clock source >>> + - description: USB3 PHY pipe clock source >>> + >>> + clock-names: >>> + items: >>> + - const: xo >>> + - const: sleep_clk >>> + - const: bias_pll_ubi_nc_clk >>> + - const: pcie30_phy0_pipe_clk >>> + - const: pcie30_phy1_pipe_clk >>> + - const: pcie30_phy2_pipe_clk >>> + - const: pcie30_phy3_pipe_clk >>> + - const: usb3phy_0_cc_pipe_clk >> >> "clock-names" gives the impression that the order of clocks can be >> modified, but we use .index in the driver. So please drop clock-names, >> just to avoid the possible confusion. >> Sure, will drop it in next spin. Missed to respond in the previous thread >> Thanks, >> Bjorn >> >>> + >>> +required: >>> + - compatible >>> + - clocks >>> + >>> +allOf: >>> + - $ref: qcom,gcc.yaml# >>> + >>> +unevaluatedProperties: false >>> + >>> +examples: >>> + - | >>> + clock-controller@1800000 { >>> + compatible = "qcom,ipq9574-gcc"; >>> + reg = <0x01800000 0x80000>; >>> + clocks = <&xo_board_clk>, >>> + <&sleep_clk>, >>> + <&bias_pll_ubi_nc_clk>, >>> + <&pcie30_phy0_pipe_clk>, >>> + <&pcie30_phy1_pipe_clk>, >>> + <&pcie30_phy2_pipe_clk>, >>> + <&pcie30_phy3_pipe_clk>, >>> + <&usb3phy_0_cc_pipe_clk>; >>> + #clock-cells = <1>; >>> + #reset-cells = <1>; >>> + #power-domain-cells = <1>; >>> + }; >>> +... >>> diff --git a/include/dt-bindings/clock/qcom,ipq9574-gcc.h >>> b/include/dt-bindings/clock/qcom,ipq9574-gcc.h >>> new file mode 100644 >>> index 000000000000..feedfdd5e00a >>> --- /dev/null >>> +++ b/include/dt-bindings/clock/qcom,ipq9574-gcc.h >>> @@ -0,0 +1,213 @@ >>> +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ >>> +/* >>> + * Copyright (c) 2018-2023 The Linux Foundation. All rights reserved. >>> + */ >>> + >>> +#ifndef _DT_BINDINGS_CLOCK_IPQ_GCC_9048_H >>> +#define _DT_BINDINGS_CLOCK_IPQ_GCC_9048_H >>> + >>> +#define GPLL0_MAIN 0 >>> +#define GPLL0 1 >>> +#define GPLL2_MAIN 2 >>> +#define GPLL2 3 >>> +#define GPLL4_MAIN 4 >>> +#define GPLL4 5 >>> +#define GCC_SLEEP_CLK_SRC 6 >>> +#define APSS_AHB_CLK_SRC 7 >>> +#define APSS_AXI_CLK_SRC 8 >>> +#define BLSP1_QUP1_I2C_APPS_CLK_SRC 9 >>> +#define BLSP1_QUP1_SPI_APPS_CLK_SRC 10 >>> +#define BLSP1_QUP2_I2C_APPS_CLK_SRC 11 >>> +#define BLSP1_QUP2_SPI_APPS_CLK_SRC 12 >>> +#define BLSP1_QUP3_I2C_APPS_CLK_SRC 13 >>> +#define BLSP1_QUP3_SPI_APPS_CLK_SRC 14 >>> +#define BLSP1_QUP4_I2C_APPS_CLK_SRC 15 >>> +#define BLSP1_QUP4_SPI_APPS_CLK_SRC 16 >>> +#define BLSP1_QUP5_I2C_APPS_CLK_SRC 17 >>> +#define BLSP1_QUP5_SPI_APPS_CLK_SRC 18 >>> +#define BLSP1_QUP6_I2C_APPS_CLK_SRC 19 >>> +#define BLSP1_QUP6_SPI_APPS_CLK_SRC 20 >>> +#define BLSP1_UART1_APPS_CLK_SRC 21 >>> +#define BLSP1_UART2_APPS_CLK_SRC 22 >>> +#define BLSP1_UART3_APPS_CLK_SRC 23 >>> +#define BLSP1_UART4_APPS_CLK_SRC 24 >>> +#define BLSP1_UART5_APPS_CLK_SRC 25 >>> +#define BLSP1_UART6_APPS_CLK_SRC 26 >>> +#define GCC_APSS_AHB_CLK 27 >>> +#define GCC_APSS_AXI_CLK 28 >>> +#define GCC_BLSP1_QUP1_I2C_APPS_CLK 29 >>> +#define GCC_BLSP1_QUP1_SPI_APPS_CLK 30 >>> +#define GCC_BLSP1_QUP2_I2C_APPS_CLK 31 >>> +#define GCC_BLSP1_QUP2_SPI_APPS_CLK 32 >>> +#define GCC_BLSP1_QUP3_I2C_APPS_CLK 33 >>> +#define GCC_BLSP1_QUP3_SPI_APPS_CLK 34 >>> +#define GCC_BLSP1_QUP4_I2C_APPS_CLK 35 >>> +#define GCC_BLSP1_QUP4_SPI_APPS_CLK 36 >>> +#define GCC_BLSP1_QUP5_I2C_APPS_CLK 37 >>> +#define GCC_BLSP1_QUP5_SPI_APPS_CLK 38 >>> +#define GCC_BLSP1_QUP6_I2C_APPS_CLK 39 >>> +#define GCC_BLSP1_QUP6_SPI_APPS_CLK 40 >>> +#define GCC_BLSP1_UART1_APPS_CLK 41 >>> +#define GCC_BLSP1_UART2_APPS_CLK 42 >>> +#define GCC_BLSP1_UART3_APPS_CLK 43 >>> +#define GCC_BLSP1_UART4_APPS_CLK 44 >>> +#define GCC_BLSP1_UART5_APPS_CLK 45 >>> +#define GCC_BLSP1_UART6_APPS_CLK 46 >>> +#define PCIE0_AXI_M_CLK_SRC 47 >>> +#define GCC_PCIE0_AXI_M_CLK 48 >>> +#define PCIE1_AXI_M_CLK_SRC 49 >>> +#define GCC_PCIE1_AXI_M_CLK 50 >>> +#define PCIE2_AXI_M_CLK_SRC 51 >>> +#define GCC_PCIE2_AXI_M_CLK 52 >>> +#define PCIE3_AXI_M_CLK_SRC 53 >>> +#define GCC_PCIE3_AXI_M_CLK 54 >>> +#define PCIE0_AXI_S_CLK_SRC 55 >>> +#define GCC_PCIE0_AXI_S_BRIDGE_CLK 56 >>> +#define GCC_PCIE0_AXI_S_CLK 57 >>> +#define PCIE1_AXI_S_CLK_SRC 58 >>> +#define GCC_PCIE1_AXI_S_BRIDGE_CLK 59 >>> +#define GCC_PCIE1_AXI_S_CLK 60 >>> +#define PCIE2_AXI_S_CLK_SRC 61 >>> +#define GCC_PCIE2_AXI_S_BRIDGE_CLK 62 >>> +#define GCC_PCIE2_AXI_S_CLK 63 >>> +#define PCIE3_AXI_S_CLK_SRC 64 >>> +#define GCC_PCIE3_AXI_S_BRIDGE_CLK 65 >>> +#define GCC_PCIE3_AXI_S_CLK 66 >>> +#define PCIE0_PIPE_CLK_SRC 67 >>> +#define PCIE1_PIPE_CLK_SRC 68 >>> +#define PCIE2_PIPE_CLK_SRC 69 >>> +#define PCIE3_PIPE_CLK_SRC 70 >>> +#define PCIE_AUX_CLK_SRC 71 >>> +#define GCC_PCIE0_AUX_CLK 72 >>> +#define GCC_PCIE1_AUX_CLK 73 >>> +#define GCC_PCIE2_AUX_CLK 74 >>> +#define GCC_PCIE3_AUX_CLK 75 >>> +#define PCIE0_RCHNG_CLK_SRC 76 >>> +#define GCC_PCIE0_RCHNG_CLK 77 >>> +#define PCIE1_RCHNG_CLK_SRC 78 >>> +#define GCC_PCIE1_RCHNG_CLK 79 >>> +#define PCIE2_RCHNG_CLK_SRC 80 >>> +#define GCC_PCIE2_RCHNG_CLK 81 >>> +#define PCIE3_RCHNG_CLK_SRC 82 >>> +#define GCC_PCIE3_RCHNG_CLK 83 >>> +#define GCC_PCIE0_AHB_CLK 84 >>> +#define GCC_PCIE1_AHB_CLK 85 >>> +#define GCC_PCIE2_AHB_CLK 86 >>> +#define GCC_PCIE3_AHB_CLK 87 >>> +#define USB0_AUX_CLK_SRC 88 >>> +#define GCC_USB0_AUX_CLK 89 >>> +#define USB0_MASTER_CLK_SRC 90 >>> +#define GCC_USB0_MASTER_CLK 91 >>> +#define GCC_SNOC_USB_CLK 92 >>> +#define GCC_ANOC_USB_AXI_CLK 93 >>> +#define USB0_MOCK_UTMI_CLK_SRC 94 >>> +#define USB0_MOCK_UTMI_DIV_CLK_SRC 95 >>> +#define GCC_USB0_MOCK_UTMI_CLK 96 >>> +#define USB0_PIPE_CLK_SRC 97 >>> +#define GCC_USB0_PHY_CFG_AHB_CLK 98 >>> +#define SDCC1_APPS_CLK_SRC 99 >>> +#define GCC_SDCC1_APPS_CLK 100 >>> +#define SDCC1_ICE_CORE_CLK_SRC 101 >>> +#define GCC_SDCC1_ICE_CORE_CLK 102 >>> +#define GCC_SDCC1_AHB_CLK 103 >>> +#define PCNOC_BFDCD_CLK_SRC 104 >>> +#define GCC_NSSCFG_CLK 105 >>> +#define GCC_NSSNOC_NSSCC_CLK 106 >>> +#define GCC_NSSCC_CLK 107 >>> +#define GCC_NSSNOC_PCNOC_1_CLK 108 >>> +#define GCC_QDSS_DAP_AHB_CLK 109 >>> +#define GCC_QDSS_CFG_AHB_CLK 110 >>> +#define GCC_QPIC_AHB_CLK 111 >>> +#define GCC_QPIC_CLK 112 >>> +#define GCC_BLSP1_AHB_CLK 113 >>> +#define GCC_MDIO_AHB_CLK 114 >>> +#define GCC_PRNG_AHB_CLK 115 >>> +#define GCC_UNIPHY0_AHB_CLK 116 >>> +#define GCC_UNIPHY1_AHB_CLK 117 >>> +#define GCC_UNIPHY2_AHB_CLK 118 >>> +#define GCC_CMN_12GPLL_AHB_CLK 119 >>> +#define GCC_CMN_12GPLL_APU_CLK 120 >>> +#define SYSTEM_NOC_BFDCD_CLK_SRC 121 >>> +#define GCC_NSSNOC_SNOC_CLK 122 >>> +#define GCC_NSSNOC_SNOC_1_CLK 123 >>> +#define GCC_QDSS_ETR_USB_CLK 124 >>> +#define WCSS_AHB_CLK_SRC 125 >>> +#define GCC_Q6_AHB_CLK 126 >>> +#define GCC_Q6_AHB_S_CLK 127 >>> +#define GCC_WCSS_ECAHB_CLK 128 >>> +#define GCC_WCSS_ACMT_CLK 129 >>> +#define GCC_SYS_NOC_WCSS_AHB_CLK 130 >>> +#define WCSS_AXI_M_CLK_SRC 131 >>> +#define GCC_ANOC_WCSS_AXI_M_CLK 132 >>> +#define QDSS_AT_CLK_SRC 133 >>> +#define GCC_Q6SS_ATBM_CLK 134 >>> +#define GCC_WCSS_DBG_IFC_ATB_CLK 135 >>> +#define GCC_NSSNOC_ATB_CLK 136 >>> +#define GCC_QDSS_AT_CLK 137 >>> +#define GCC_SYS_NOC_AT_CLK 138 >>> +#define GCC_PCNOC_AT_CLK 139 >>> +#define GCC_USB0_EUD_AT_CLK 140 >>> +#define GCC_QDSS_EUD_AT_CLK 141 >>> +#define QDSS_STM_CLK_SRC 142 >>> +#define GCC_QDSS_STM_CLK 143 >>> +#define GCC_SYS_NOC_QDSS_STM_AXI_CLK 144 >>> +#define QDSS_TRACECLKIN_CLK_SRC 145 >>> +#define GCC_QDSS_TRACECLKIN_CLK 146 >>> +#define QDSS_TSCTR_CLK_SRC 147 >>> +#define GCC_Q6_TSCTR_1TO2_CLK 148 >>> +#define GCC_WCSS_DBG_IFC_NTS_CLK 149 >>> +#define GCC_QDSS_TSCTR_DIV2_CLK 150 >>> +#define GCC_QDSS_TS_CLK 151 >>> +#define GCC_QDSS_TSCTR_DIV4_CLK 152 >>> +#define GCC_NSS_TS_CLK 153 >>> +#define GCC_QDSS_TSCTR_DIV8_CLK 154 >>> +#define GCC_QDSS_TSCTR_DIV16_CLK 155 >>> +#define GCC_Q6SS_PCLKDBG_CLK 156 >>> +#define GCC_Q6SS_TRIG_CLK 157 >>> +#define GCC_WCSS_DBG_IFC_APB_CLK 158 >>> +#define GCC_WCSS_DBG_IFC_DAPBUS_CLK 159 >>> +#define GCC_QDSS_DAP_CLK 160 >>> +#define GCC_QDSS_APB2JTAG_CLK 161 >>> +#define GCC_QDSS_TSCTR_DIV3_CLK 162 >>> +#define QPIC_IO_MACRO_CLK_SRC 163 >>> +#define GCC_QPIC_IO_MACRO_CLK 164 >>> +#define Q6_AXI_CLK_SRC 165 >>> +#define GCC_Q6_AXIM_CLK 166 >>> +#define GCC_WCSS_Q6_TBU_CLK 167 >>> +#define GCC_MEM_NOC_Q6_AXI_CLK 168 >>> +#define Q6_AXIM2_CLK_SRC 169 >>> +#define NSSNOC_MEMNOC_BFDCD_CLK_SRC 170 >>> +#define GCC_NSSNOC_MEMNOC_CLK 171 >>> +#define GCC_NSSNOC_MEM_NOC_1_CLK 172 >>> +#define GCC_NSS_TBU_CLK 173 >>> +#define GCC_MEM_NOC_NSSNOC_CLK 174 >>> +#define LPASS_AXIM_CLK_SRC 175 >>> +#define LPASS_SWAY_CLK_SRC 176 >>> +#define ADSS_PWM_CLK_SRC 177 >>> +#define GCC_ADSS_PWM_CLK 178 >>> +#define GP1_CLK_SRC 179 >>> +#define GP2_CLK_SRC 180 >>> +#define GP3_CLK_SRC 181 >>> +#define DDRSS_SMS_SLOW_CLK_SRC 182 >>> +#define GCC_XO_CLK_SRC 183 >>> +#define GCC_XO_CLK 184 >>> +#define GCC_NSSNOC_QOSGEN_REF_CLK 185 >>> +#define GCC_NSSNOC_TIMEOUT_REF_CLK 186 >>> +#define GCC_XO_DIV4_CLK 187 >>> +#define GCC_UNIPHY0_SYS_CLK 188 >>> +#define GCC_UNIPHY1_SYS_CLK 189 >>> +#define GCC_UNIPHY2_SYS_CLK 190 >>> +#define GCC_CMN_12GPLL_SYS_CLK 191 >>> +#define GCC_NSSNOC_XO_DCD_CLK 192 >>> +#define GCC_Q6SS_BOOT_CLK 193 >>> +#define UNIPHY_SYS_CLK_SRC 194 >>> +#define NSS_TS_CLK_SRC 195 >>> +#define GCC_ANOC_PCIE0_1LANE_M_CLK 196 >>> +#define GCC_ANOC_PCIE1_1LANE_M_CLK 197 >>> +#define GCC_ANOC_PCIE2_2LANE_M_CLK 198 >>> +#define GCC_ANOC_PCIE3_2LANE_M_CLK 199 >>> +#define GCC_SNOC_PCIE0_1LANE_S_CLK 200 >>> +#define GCC_SNOC_PCIE1_1LANE_S_CLK 201 >>> +#define GCC_SNOC_PCIE2_2LANE_S_CLK 202 >>> +#define GCC_SNOC_PCIE3_2LANE_S_CLK 203 >>> +#endif >>> diff --git a/include/dt-bindings/reset/qcom,ipq9574-gcc.h >>> b/include/dt-bindings/reset/qcom,ipq9574-gcc.h >>> new file mode 100644 >>> index 000000000000..a11adbda45ec >>> --- /dev/null >>> +++ b/include/dt-bindings/reset/qcom,ipq9574-gcc.h >>> @@ -0,0 +1,164 @@ >>> +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ >>> +/* >>> + * Copyright (c) 2018-2023, The Linux Foundation. All rights reserved. >>> + */ >>> + >>> +#ifndef _DT_BINDINGS_RESET_IPQ_GCC_9048_H >>> +#define _DT_BINDINGS_RESET_IPQ_GCC_9048_H >>> + >>> +#define GCC_ADSS_BCR 0 >>> +#define GCC_APC0_VOLTAGE_DROOP_DETECTOR_BCR 1 >>> +#define GCC_BLSP1_BCR 2 >>> +#define GCC_BLSP1_QUP1_BCR 3 >>> +#define GCC_BLSP1_QUP2_BCR 4 >>> +#define GCC_BLSP1_QUP3_BCR 5 >>> +#define GCC_BLSP1_QUP4_BCR 6 >>> +#define GCC_BLSP1_QUP5_BCR 7 >>> +#define GCC_BLSP1_QUP6_BCR 8 >>> +#define GCC_BLSP1_UART1_BCR 9 >>> +#define GCC_BLSP1_UART2_BCR 10 >>> +#define GCC_BLSP1_UART3_BCR 11 >>> +#define GCC_BLSP1_UART4_BCR 12 >>> +#define GCC_BLSP1_UART5_BCR 13 >>> +#define GCC_BLSP1_UART6_BCR 14 >>> +#define GCC_BOOT_ROM_BCR 15 >>> +#define GCC_MDIO_BCR 16 >>> +#define GCC_NSS_BCR 17 >>> +#define GCC_NSS_TBU_BCR 18 >>> +#define GCC_PCIE0_BCR 19 >>> +#define GCC_PCIE0_LINK_DOWN_BCR 20 >>> +#define GCC_PCIE0_PHY_BCR 21 >>> +#define GCC_PCIE0PHY_PHY_BCR 22 >>> +#define GCC_PCIE1_BCR 23 >>> +#define GCC_PCIE1_LINK_DOWN_BCR 24 >>> +#define GCC_PCIE1_PHY_BCR 25 >>> +#define GCC_PCIE1PHY_PHY_BCR 26 >>> +#define GCC_PCIE2_BCR 27 >>> +#define GCC_PCIE2_LINK_DOWN_BCR 28 >>> +#define GCC_PCIE2_PHY_BCR 29 >>> +#define GCC_PCIE2PHY_PHY_BCR 30 >>> +#define GCC_PCIE3_BCR 31 >>> +#define GCC_PCIE3_LINK_DOWN_BCR 32 >>> +#define GCC_PCIE3_PHY_BCR 33 >>> +#define GCC_PCIE3PHY_PHY_BCR 34 >>> +#define GCC_PRNG_BCR 35 >>> +#define GCC_QUSB2_0_PHY_BCR 36 >>> +#define GCC_SDCC_BCR 37 >>> +#define GCC_TLMM_BCR 38 >>> +#define GCC_UNIPHY0_BCR 39 >>> +#define GCC_UNIPHY1_BCR 40 >>> +#define GCC_UNIPHY2_BCR 41 >>> +#define GCC_USB0_PHY_BCR 42 >>> +#define GCC_USB3PHY_0_PHY_BCR 43 >>> +#define GCC_USB_BCR 44 >>> +#define GCC_ANOC0_TBU_BCR 45 >>> +#define GCC_ANOC1_TBU_BCR 46 >>> +#define GCC_ANOC_BCR 47 >>> +#define GCC_APSS_TCU_BCR 48 >>> +#define GCC_CMN_BLK_BCR 49 >>> +#define GCC_CMN_BLK_AHB_ARES 50 >>> +#define GCC_CMN_BLK_SYS_ARES 51 >>> +#define GCC_CMN_BLK_APU_ARES 52 >>> +#define GCC_DCC_BCR 53 >>> +#define GCC_DDRSS_BCR 54 >>> +#define GCC_IMEM_BCR 55 >>> +#define GCC_LPASS_BCR 56 >>> +#define GCC_MPM_BCR 57 >>> +#define GCC_MSG_RAM_BCR 58 >>> +#define GCC_NSSNOC_MEMNOC_1_ARES 59 >>> +#define GCC_NSSNOC_PCNOC_1_ARES 60 >>> +#define GCC_NSSNOC_SNOC_1_ARES 61 >>> +#define GCC_NSSNOC_XO_DCD_ARES 62 >>> +#define GCC_NSSNOC_TS_ARES 63 >>> +#define GCC_NSSCC_ARES 64 >>> +#define GCC_NSSNOC_NSSCC_ARES 65 >>> +#define GCC_NSSNOC_ATB_ARES 66 >>> +#define GCC_NSSNOC_MEMNOC_ARES 67 >>> +#define GCC_NSSNOC_QOSGEN_REF_ARES 68 >>> +#define GCC_NSSNOC_SNOC_ARES 69 >>> +#define GCC_NSSNOC_TIMEOUT_REF_ARES 70 >>> +#define GCC_NSS_CFG_ARES 71 >>> +#define GCC_UBI0_DBG_ARES 72 >>> +#define GCC_PCIE0_AHB_ARES 73 >>> +#define GCC_PCIE0_AUX_ARES 74 >>> +#define GCC_PCIE0_AXI_M_ARES 75 >>> +#define GCC_PCIE0_AXI_M_STICKY_ARES 76 >>> +#define GCC_PCIE0_AXI_S_ARES 77 >>> +#define GCC_PCIE0_AXI_S_STICKY_ARES 78 >>> +#define GCC_PCIE0_CORE_STICKY_ARES 79 >>> +#define GCC_PCIE0_PIPE_ARES 80 >>> +#define GCC_PCIE1_AHB_ARES 81 >>> +#define GCC_PCIE1_AUX_ARES 82 >>> +#define GCC_PCIE1_AXI_M_ARES 83 >>> +#define GCC_PCIE1_AXI_M_STICKY_ARES 84 >>> +#define GCC_PCIE1_AXI_S_ARES 85 >>> +#define GCC_PCIE1_AXI_S_STICKY_ARES 86 >>> +#define GCC_PCIE1_CORE_STICKY_ARES 87 >>> +#define GCC_PCIE1_PIPE_ARES 88 >>> +#define GCC_PCIE2_AHB_ARES 89 >>> +#define GCC_PCIE2_AUX_ARES 90 >>> +#define GCC_PCIE2_AXI_M_ARES 91 >>> +#define GCC_PCIE2_AXI_M_STICKY_ARES 92 >>> +#define GCC_PCIE2_AXI_S_ARES 93 >>> +#define GCC_PCIE2_AXI_S_STICKY_ARES 94 >>> +#define GCC_PCIE2_CORE_STICKY_ARES 95 >>> +#define GCC_PCIE2_PIPE_ARES 96 >>> +#define GCC_PCIE3_AHB_ARES 97 >>> +#define GCC_PCIE3_AUX_ARES 98 >>> +#define GCC_PCIE3_AXI_M_ARES 99 >>> +#define GCC_PCIE3_AXI_M_STICKY_ARES 100 >>> +#define GCC_PCIE3_AXI_S_ARES 101 >>> +#define GCC_PCIE3_AXI_S_STICKY_ARES 102 >>> +#define GCC_PCIE3_CORE_STICKY_ARES 103 >>> +#define GCC_PCIE3_PIPE_ARES 104 >>> +#define GCC_PCNOC_BCR 105 >>> +#define GCC_PCNOC_BUS_TIMEOUT0_BCR 106 >>> +#define GCC_PCNOC_BUS_TIMEOUT1_BCR 107 >>> +#define GCC_PCNOC_BUS_TIMEOUT2_BCR 108 >>> +#define GCC_PCNOC_BUS_TIMEOUT3_BCR 109 >>> +#define GCC_PCNOC_BUS_TIMEOUT4_BCR 110 >>> +#define GCC_PCNOC_BUS_TIMEOUT5_BCR 111 >>> +#define GCC_PCNOC_BUS_TIMEOUT6_BCR 112 >>> +#define GCC_PCNOC_BUS_TIMEOUT7_BCR 113 >>> +#define GCC_PCNOC_BUS_TIMEOUT8_BCR 114 >>> +#define GCC_PCNOC_BUS_TIMEOUT9_BCR 115 >>> +#define GCC_PCNOC_TBU_BCR 116 >>> +#define GCC_Q6SS_DBG_ARES 117 >>> +#define GCC_Q6_AHB_ARES 118 >>> +#define GCC_Q6_AHB_S_ARES 119 >>> +#define GCC_Q6_AXIM2_ARES 120 >>> +#define GCC_Q6_AXIM_ARES 121 >>> +#define GCC_QDSS_BCR 122 >>> +#define GCC_QPIC_BCR 123 >>> +#define GCC_QPIC_AHB_ARES 124 >>> +#define GCC_QPIC_ARES 125 >>> +#define GCC_RBCPR_BCR 126 >>> +#define GCC_RBCPR_MX_BCR 127 >>> +#define GCC_SEC_CTRL_BCR 128 >>> +#define GCC_SMMU_CFG_BCR 129 >>> +#define GCC_SNOC_BCR 130 >>> +#define GCC_SPDM_BCR 131 >>> +#define GCC_TME_BCR 132 >>> +#define GCC_UNIPHY0_SYS_RESET 133 >>> +#define GCC_UNIPHY0_AHB_RESET 134 >>> +#define GCC_UNIPHY0_XPCS_RESET 135 >>> +#define GCC_UNIPHY1_SYS_RESET 136 >>> +#define GCC_UNIPHY1_AHB_RESET 137 >>> +#define GCC_UNIPHY1_XPCS_RESET 138 >>> +#define GCC_UNIPHY2_SYS_RESET 139 >>> +#define GCC_UNIPHY2_AHB_RESET 140 >>> +#define GCC_UNIPHY2_XPCS_RESET 141 >>> +#define GCC_USB_MISC_RESET 142 >>> +#define GCC_WCSSAON_RESET 143 >>> +#define GCC_WCSS_ACMT_ARES 144 >>> +#define GCC_WCSS_AHB_S_ARES 145 >>> +#define GCC_WCSS_AXI_M_ARES 146 >>> +#define GCC_WCSS_BCR 147 >>> +#define GCC_WCSS_DBG_ARES 148 >>> +#define GCC_WCSS_DBG_BDG_ARES 149 >>> +#define GCC_WCSS_ECAHB_ARES 150 >>> +#define GCC_WCSS_Q6_BCR 151 >>> +#define GCC_WCSS_Q6_TBU_BCR 152 >>> +#define GCC_TCSR_BCR 153 >>> + >>> +#endif >>> -- >>> 2.17.1 >>> ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH V3 3/7] dt-bindings: pinctrl: qcom: Add support for IPQ9574 2023-01-30 12:55 [PATCH V3 0/7] Add minimal boot support for IPQ9574 devi priya 2023-01-30 12:55 ` [PATCH V3 1/7] dt-bindings: Add ipq9574 clock and reset definitions devi priya @ 2023-01-30 12:55 ` devi priya 2023-01-31 18:12 ` Krzysztof Kozlowski 2023-01-30 12:55 ` [PATCH V3 4/7] pinctrl: qcom: Add IPQ9574 pinctrl driver devi priya ` (4 subsequent siblings) 6 siblings, 1 reply; 19+ messages in thread From: devi priya @ 2023-01-30 12:55 UTC (permalink / raw) To: agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh Add new binding document for pinctrl on IPQ9574 Co-developed-by: Anusha Rao <quic_anusha@quicinc.com> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com> Signed-off-by: devi priya <quic_devipriy@quicinc.com> --- Changes in V3: - Added 'maxItems' for 'interrupts' property - Updated the subject Changes in V2: - Rebased the binding to the latest style - Updated the indentation and ordered the enums by name .../bindings/pinctrl/qcom,ipq9574-tlmm.yaml | 137 ++++++++++++++++++ 1 file changed, 137 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq9574-tlmm.yaml diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq9574-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq9574-tlmm.yaml new file mode 100644 index 000000000000..053b15ccb7a5 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq9574-tlmm.yaml @@ -0,0 +1,137 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq9574-tlmm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. IPQ9574 TLMM block + +maintainers: + - Bjorn Andersson <andersson@kernel.org> + - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> + +description: + Top Level Mode Multiplexer pin controller in Qualcomm IPQ9574 SoC. + +properties: + compatible: + const: qcom,ipq9574-tlmm + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + interrupt-controller: true + "#interrupt-cells": true + gpio-controller: true + "#gpio-cells": true + gpio-ranges: true + wakeup-parent: true + + gpio-reserved-ranges: + minItems: 1 + maxItems: 33 + + gpio-line-names: + maxItems: 65 + +patternProperties: + "-state$": + oneOf: + - $ref: "#/$defs/qcom-ipq9574-tlmm-state" + - patternProperties: + "-pins$": + $ref: "#/$defs/qcom-ipq9574-tlmm-state" + additionalProperties: false + +$defs: + qcom-ipq9574-tlmm-state: + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + oneOf: + - pattern: "^gpio([0-9]|[1-5][0-9]|6[0-4])$" + - enum: [ qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2, qdsd_cmd, + qdsd_data0, qdsd_data1, qdsd_data2, qdsd_data3, sdc1_clk, + sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data ] + minItems: 1 + maxItems: 8 + + function: + description: + Specify the alternative function to be configured for the specified + pins. + + enum: [ atest_char, atest_char0, atest_char1, atest_char2, atest_char3, + audio_pdm0, audio_pdm1, audio_pri, audio_sec, blsp0_spi, blsp0_uart, + blsp1_i2c, blsp1_spi, blsp1_uart, blsp2_i2c, blsp2_spi, + blsp2_uart, blsp3_i2c, blsp3_spi, blsp3_uart, blsp4_i2c, + blsp4_spi, blsp4_uart, blsp5_i2c, blsp5_uart, cri_trng0, + cri_trng1, cri_trng3, cxc0, cxc1, dbg_out, dwc_ddrphy, + gcc_plltest, gcc_tlmm, mac00, mac01, mac10, mac11, mdc, + mdio, pcie0_clk, pcie0_wake, pcie1_clk, pcie1_wake, pcie2_clk, + pcie2_wake, pcie3_clk, pcie3_wake, prng_rosc0, prng_rosc1, + prng_rosc2, prng_rosc3, pta1_0, pta1_1, pta1_2, pta20, pta21, + pwm00, pwm01, pwm02, pwm03, pwm04, pwm10, pwm11, pwm12, pwm13, + pwm14, pwm20, pwm21, pwm22, pwm23, pwm24, pwm30, pwm31, pwm32, + pwm33, qdss_cti_trig_in_a0, qdss_cti_trig_in_a1, qdss_cti_trig_in_b0, + qdss_cti_trig_in_b1, qdss_cti_trig_out_a0, qdss_cti_trig_out_a1, + qdss_cti_trig_out_b0, qdss_cti_trig_out_b1, qdss_traceclk_a, + qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b, qdss_tracedata_a, + qdss_tracedata_b, qdss_tracedata_b, qspi_clk, qspi_cs, qspi_data, + rx0, rx1, sdc_clk, sdc_cmd, sdc_data, sdc_rclk, tsens_max, + wci20, wci21, wsa_swrm ] + + bias-pull-down: true + bias-pull-up: true + bias-disable: true + drive-strength: true + input-enable: true + output-high: true + output-low: true + + required: + - pins + + additionalProperties: false + +allOf: + - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq9574-tlmm"; + reg = <0x01000000 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 65>; + + uart2-state { + pins = "gpio34", "gpio35"; + function = "blsp2_uart"; + drive-strength = <8>; + bias-pull-down; + }; + }; -- 2.17.1 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH V3 3/7] dt-bindings: pinctrl: qcom: Add support for IPQ9574 2023-01-30 12:55 ` [PATCH V3 3/7] dt-bindings: pinctrl: qcom: Add support for IPQ9574 devi priya @ 2023-01-31 18:12 ` Krzysztof Kozlowski 0 siblings, 0 replies; 19+ messages in thread From: Krzysztof Kozlowski @ 2023-01-31 18:12 UTC (permalink / raw) To: devi priya, agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh On 30/01/2023 13:55, devi priya wrote: > Add new binding document for pinctrl on IPQ9574 > > Co-developed-by: Anusha Rao <quic_anusha@quicinc.com> > Signed-off-by: Anusha Rao <quic_anusha@quicinc.com> > Signed-off-by: devi priya <quic_devipriy@quicinc.com> > --- Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Best regards, Krzysztof ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH V3 4/7] pinctrl: qcom: Add IPQ9574 pinctrl driver 2023-01-30 12:55 [PATCH V3 0/7] Add minimal boot support for IPQ9574 devi priya 2023-01-30 12:55 ` [PATCH V3 1/7] dt-bindings: Add ipq9574 clock and reset definitions devi priya 2023-01-30 12:55 ` [PATCH V3 3/7] dt-bindings: pinctrl: qcom: Add support for IPQ9574 devi priya @ 2023-01-30 12:55 ` devi priya 2023-02-08 23:14 ` Bjorn Andersson 2023-01-30 12:55 ` [PATCH V3 5/7] dt-bindings: arm: qcom: Add ipq9574 compatible devi priya ` (3 subsequent siblings) 6 siblings, 1 reply; 19+ messages in thread From: devi priya @ 2023-01-30 12:55 UTC (permalink / raw) To: agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh Add pinctrl definitions for the TLMM of IPQ9574 Co-developed-by: Anusha Rao <quic_anusha@quicinc.com> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com> Signed-off-by: devi priya <quic_devipriy@quicinc.com> --- Changes in V3: - Grouped up the individual pin entries corresponding to pwm, pta and mac - Added comment for reserving gpio59 Changes in V2: - Updated the Kconfig to the latest style - Added reserved_gpios list to the pinctrl driver drivers/pinctrl/qcom/Kconfig | 11 + drivers/pinctrl/qcom/Makefile | 1 + drivers/pinctrl/qcom/pinctrl-ipq9574.c | 861 +++++++++++++++++++++++++ 3 files changed, 873 insertions(+) create mode 100644 drivers/pinctrl/qcom/pinctrl-ipq9574.c diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig index 2a517775a61e..ff01d4d3f03a 100644 --- a/drivers/pinctrl/qcom/Kconfig +++ b/drivers/pinctrl/qcom/Kconfig @@ -70,6 +70,17 @@ config PINCTRL_IPQ6018 Qualcomm Technologies Inc. IPQ6018 platform. Select this for IPQ6018. +config PINCTRL_IPQ9574 + tristate "Qualcomm Technologies, Inc. IPQ9574 pin controller driver" + depends on OF + depends on ARM64 || COMPILE_TEST + depends on PINCTRL_MSM + help + This is the pinctrl, pinmux, pinconf and gpiolib driver for + the Qualcomm Technologies Inc. TLMM block found on the + Qualcomm Technologies Inc. IPQ9574 platform. Select this for + IPQ9574. + config PINCTRL_MSM8226 tristate "Qualcomm 8226 pin controller driver" depends on OF diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile index 952f784d0888..1579fbb24cb2 100644 --- a/drivers/pinctrl/qcom/Makefile +++ b/drivers/pinctrl/qcom/Makefile @@ -7,6 +7,7 @@ obj-$(CONFIG_PINCTRL_IPQ4019) += pinctrl-ipq4019.o obj-$(CONFIG_PINCTRL_IPQ8064) += pinctrl-ipq8064.o obj-$(CONFIG_PINCTRL_IPQ8074) += pinctrl-ipq8074.o obj-$(CONFIG_PINCTRL_IPQ6018) += pinctrl-ipq6018.o +obj-$(CONFIG_PINCTRL_IPQ9574) += pinctrl-ipq9574.o obj-$(CONFIG_PINCTRL_MSM8226) += pinctrl-msm8226.o obj-$(CONFIG_PINCTRL_MSM8660) += pinctrl-msm8660.o obj-$(CONFIG_PINCTRL_MSM8960) += pinctrl-msm8960.o diff --git a/drivers/pinctrl/qcom/pinctrl-ipq9574.c b/drivers/pinctrl/qcom/pinctrl-ipq9574.c new file mode 100644 index 000000000000..7c4cf47647f1 --- /dev/null +++ b/drivers/pinctrl/qcom/pinctrl-ipq9574.c @@ -0,0 +1,861 @@ +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +/* + * Copyright (c) 2023 The Linux Foundation. All rights reserved. + */ + +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/pinctrl/pinctrl.h> + +#include "pinctrl-msm.h" + +#define FUNCTION(fname) \ + [msm_mux_##fname] = { \ + .name = #fname, \ + .groups = fname##_groups, \ + .ngroups = ARRAY_SIZE(fname##_groups), \ + } + +#define REG_SIZE 0x1000 +#define PINGROUP(id, f1, f2, f3, f4, f5, f6, f7, f8, f9) \ + { \ + .name = "gpio" #id, \ + .pins = gpio##id##_pins, \ + .npins = (unsigned int)ARRAY_SIZE(gpio##id##_pins), \ + .funcs = (int[]){ \ + msm_mux_gpio, /* gpio mode */ \ + msm_mux_##f1, \ + msm_mux_##f2, \ + msm_mux_##f3, \ + msm_mux_##f4, \ + msm_mux_##f5, \ + msm_mux_##f6, \ + msm_mux_##f7, \ + msm_mux_##f8, \ + msm_mux_##f9 \ + }, \ + .nfuncs = 10, \ + .ctl_reg = REG_SIZE * id, \ + .io_reg = 0x4 + REG_SIZE * id, \ + .intr_cfg_reg = 0x8 + REG_SIZE * id, \ + .intr_status_reg = 0xc + REG_SIZE * id, \ + .intr_target_reg = 0x8 + REG_SIZE * id, \ + .mux_bit = 2, \ + .pull_bit = 0, \ + .drv_bit = 6, \ + .oe_bit = 9, \ + .in_bit = 0, \ + .out_bit = 1, \ + .intr_enable_bit = 0, \ + .intr_status_bit = 0, \ + .intr_target_bit = 5, \ + .intr_target_kpss_val = 3, \ + .intr_raw_status_bit = 4, \ + .intr_polarity_bit = 1, \ + .intr_detection_bit = 2, \ + .intr_detection_width = 2, \ + } + +static const struct pinctrl_pin_desc ipq9574_pins[] = { + PINCTRL_PIN(0, "GPIO_0"), + PINCTRL_PIN(1, "GPIO_1"), + PINCTRL_PIN(2, "GPIO_2"), + PINCTRL_PIN(3, "GPIO_3"), + PINCTRL_PIN(4, "GPIO_4"), + PINCTRL_PIN(5, "GPIO_5"), + PINCTRL_PIN(6, "GPIO_6"), + PINCTRL_PIN(7, "GPIO_7"), + PINCTRL_PIN(8, "GPIO_8"), + PINCTRL_PIN(9, "GPIO_9"), + PINCTRL_PIN(10, "GPIO_10"), + PINCTRL_PIN(11, "GPIO_11"), + PINCTRL_PIN(12, "GPIO_12"), + PINCTRL_PIN(13, "GPIO_13"), + PINCTRL_PIN(14, "GPIO_14"), + PINCTRL_PIN(15, "GPIO_15"), + PINCTRL_PIN(16, "GPIO_16"), + PINCTRL_PIN(17, "GPIO_17"), + PINCTRL_PIN(18, "GPIO_18"), + PINCTRL_PIN(19, "GPIO_19"), + PINCTRL_PIN(20, "GPIO_20"), + PINCTRL_PIN(21, "GPIO_21"), + PINCTRL_PIN(22, "GPIO_22"), + PINCTRL_PIN(23, "GPIO_23"), + PINCTRL_PIN(24, "GPIO_24"), + PINCTRL_PIN(25, "GPIO_25"), + PINCTRL_PIN(26, "GPIO_26"), + PINCTRL_PIN(27, "GPIO_27"), + PINCTRL_PIN(28, "GPIO_28"), + PINCTRL_PIN(29, "GPIO_29"), + PINCTRL_PIN(30, "GPIO_30"), + PINCTRL_PIN(31, "GPIO_31"), + PINCTRL_PIN(32, "GPIO_32"), + PINCTRL_PIN(33, "GPIO_33"), + PINCTRL_PIN(34, "GPIO_34"), + PINCTRL_PIN(35, "GPIO_35"), + PINCTRL_PIN(36, "GPIO_36"), + PINCTRL_PIN(37, "GPIO_37"), + PINCTRL_PIN(38, "GPIO_38"), + PINCTRL_PIN(39, "GPIO_39"), + PINCTRL_PIN(40, "GPIO_40"), + PINCTRL_PIN(41, "GPIO_41"), + PINCTRL_PIN(42, "GPIO_42"), + PINCTRL_PIN(43, "GPIO_43"), + PINCTRL_PIN(44, "GPIO_44"), + PINCTRL_PIN(45, "GPIO_45"), + PINCTRL_PIN(46, "GPIO_46"), + PINCTRL_PIN(47, "GPIO_47"), + PINCTRL_PIN(48, "GPIO_48"), + PINCTRL_PIN(49, "GPIO_49"), + PINCTRL_PIN(50, "GPIO_50"), + PINCTRL_PIN(51, "GPIO_51"), + PINCTRL_PIN(52, "GPIO_52"), + PINCTRL_PIN(53, "GPIO_53"), + PINCTRL_PIN(54, "GPIO_54"), + PINCTRL_PIN(55, "GPIO_55"), + PINCTRL_PIN(56, "GPIO_56"), + PINCTRL_PIN(57, "GPIO_57"), + PINCTRL_PIN(58, "GPIO_58"), + PINCTRL_PIN(59, "GPIO_59"), + PINCTRL_PIN(60, "GPIO_60"), + PINCTRL_PIN(61, "GPIO_61"), + PINCTRL_PIN(62, "GPIO_62"), + PINCTRL_PIN(63, "GPIO_63"), + PINCTRL_PIN(64, "GPIO_64"), +}; + +#define DECLARE_MSM_GPIO_PINS(pin) \ + static const unsigned int gpio##pin##_pins[] = { pin } +DECLARE_MSM_GPIO_PINS(0); +DECLARE_MSM_GPIO_PINS(1); +DECLARE_MSM_GPIO_PINS(2); +DECLARE_MSM_GPIO_PINS(3); +DECLARE_MSM_GPIO_PINS(4); +DECLARE_MSM_GPIO_PINS(5); +DECLARE_MSM_GPIO_PINS(6); +DECLARE_MSM_GPIO_PINS(7); +DECLARE_MSM_GPIO_PINS(8); +DECLARE_MSM_GPIO_PINS(9); +DECLARE_MSM_GPIO_PINS(10); +DECLARE_MSM_GPIO_PINS(11); +DECLARE_MSM_GPIO_PINS(12); +DECLARE_MSM_GPIO_PINS(13); +DECLARE_MSM_GPIO_PINS(14); +DECLARE_MSM_GPIO_PINS(15); +DECLARE_MSM_GPIO_PINS(16); +DECLARE_MSM_GPIO_PINS(17); +DECLARE_MSM_GPIO_PINS(18); +DECLARE_MSM_GPIO_PINS(19); +DECLARE_MSM_GPIO_PINS(20); +DECLARE_MSM_GPIO_PINS(21); +DECLARE_MSM_GPIO_PINS(22); +DECLARE_MSM_GPIO_PINS(23); +DECLARE_MSM_GPIO_PINS(24); +DECLARE_MSM_GPIO_PINS(25); +DECLARE_MSM_GPIO_PINS(26); +DECLARE_MSM_GPIO_PINS(27); +DECLARE_MSM_GPIO_PINS(28); +DECLARE_MSM_GPIO_PINS(29); +DECLARE_MSM_GPIO_PINS(30); +DECLARE_MSM_GPIO_PINS(31); +DECLARE_MSM_GPIO_PINS(32); +DECLARE_MSM_GPIO_PINS(33); +DECLARE_MSM_GPIO_PINS(34); +DECLARE_MSM_GPIO_PINS(35); +DECLARE_MSM_GPIO_PINS(36); +DECLARE_MSM_GPIO_PINS(37); +DECLARE_MSM_GPIO_PINS(38); +DECLARE_MSM_GPIO_PINS(39); +DECLARE_MSM_GPIO_PINS(40); +DECLARE_MSM_GPIO_PINS(41); +DECLARE_MSM_GPIO_PINS(42); +DECLARE_MSM_GPIO_PINS(43); +DECLARE_MSM_GPIO_PINS(44); +DECLARE_MSM_GPIO_PINS(45); +DECLARE_MSM_GPIO_PINS(46); +DECLARE_MSM_GPIO_PINS(47); +DECLARE_MSM_GPIO_PINS(48); +DECLARE_MSM_GPIO_PINS(49); +DECLARE_MSM_GPIO_PINS(50); +DECLARE_MSM_GPIO_PINS(51); +DECLARE_MSM_GPIO_PINS(52); +DECLARE_MSM_GPIO_PINS(53); +DECLARE_MSM_GPIO_PINS(54); +DECLARE_MSM_GPIO_PINS(55); +DECLARE_MSM_GPIO_PINS(56); +DECLARE_MSM_GPIO_PINS(57); +DECLARE_MSM_GPIO_PINS(58); +DECLARE_MSM_GPIO_PINS(59); +DECLARE_MSM_GPIO_PINS(60); +DECLARE_MSM_GPIO_PINS(61); +DECLARE_MSM_GPIO_PINS(62); +DECLARE_MSM_GPIO_PINS(63); +DECLARE_MSM_GPIO_PINS(64); + +enum ipq9574_functions { + msm_mux_atest_char, + msm_mux_atest_char0, + msm_mux_atest_char1, + msm_mux_atest_char2, + msm_mux_atest_char3, + msm_mux_audio_pdm0, + msm_mux_audio_pdm1, + msm_mux_audio_pri, + msm_mux_audio_sec, + msm_mux_blsp0_spi, + msm_mux_blsp0_uart, + msm_mux_blsp1_i2c, + msm_mux_blsp1_spi, + msm_mux_blsp1_uart, + msm_mux_blsp2_i2c, + msm_mux_blsp2_spi, + msm_mux_blsp2_uart, + msm_mux_blsp3_i2c, + msm_mux_blsp3_spi, + msm_mux_blsp3_uart, + msm_mux_blsp4_i2c, + msm_mux_blsp4_spi, + msm_mux_blsp4_uart, + msm_mux_blsp5_i2c, + msm_mux_blsp5_uart, + msm_mux_cri_trng0, + msm_mux_cri_trng1, + msm_mux_cri_trng2, + msm_mux_cri_trng3, + msm_mux_cxc0, + msm_mux_cxc1, + msm_mux_dbg_out, + msm_mux_dwc_ddrphy, + msm_mux_gcc_plltest, + msm_mux_gcc_tlmm, + msm_mux_gpio, + msm_mux_mac, + msm_mux_mdc, + msm_mux_mdio, + msm_mux_pcie0_clk, + msm_mux_pcie0_wake, + msm_mux_pcie1_clk, + msm_mux_pcie1_wake, + msm_mux_pcie2_clk, + msm_mux_pcie2_wake, + msm_mux_pcie3_clk, + msm_mux_pcie3_wake, + msm_mux_prng_rosc0, + msm_mux_prng_rosc1, + msm_mux_prng_rosc2, + msm_mux_prng_rosc3, + msm_mux_pta, + msm_mux_pwm, + msm_mux_qdss_cti_trig_in_a0, + msm_mux_qdss_cti_trig_in_a1, + msm_mux_qdss_cti_trig_in_b0, + msm_mux_qdss_cti_trig_in_b1, + msm_mux_qdss_cti_trig_out_a0, + msm_mux_qdss_cti_trig_out_a1, + msm_mux_qdss_cti_trig_out_b0, + msm_mux_qdss_cti_trig_out_b1, + msm_mux_qdss_traceclk_a, + msm_mux_qdss_traceclk_b, + msm_mux_qdss_tracectl_a, + msm_mux_qdss_tracectl_b, + msm_mux_qdss_tracedata_a, + msm_mux_qdss_tracedata_b, + msm_mux_qspi_data, + msm_mux_qspi_clk, + msm_mux_qspi_cs, + msm_mux_rx0, + msm_mux_rx1, + msm_mux_sdc_data, + msm_mux_sdc_clk, + msm_mux_sdc_cmd, + msm_mux_sdc_rclk, + msm_mux_tsens_max, + msm_mux_wci20, + msm_mux_wci21, + msm_mux_wsa_swrm, + msm_mux__, +}; + +static const char * const gpio_groups[] = { + "gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", + "gpio8", "gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", + "gpio15", "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21", + "gpio22", "gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28", + "gpio29", "gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35", + "gpio36", "gpio37", "gpio38", "gpio39", "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", "gpio46", "gpio47", "gpio48", "gpio49", + "gpio50", "gpio51", "gpio52", "gpio53", "gpio54", "gpio55", "gpio56", + "gpio57", "gpio58", "gpio59", "gpio60", "gpio61", "gpio62", "gpio63", + "gpio64", +}; + +static const char * const sdc_data_groups[] = { + "gpio0", + "gpio1", + "gpio2", + "gpio3", + "gpio6", + "gpio7", + "gpio8", + "gpio9", +}; + +static const char * const qspi_data_groups[] = { + "gpio0", + "gpio1", + "gpio2", + "gpio3", +}; + +static const char * const qdss_traceclk_b_groups[] = { + "gpio0", +}; + +static const char * const qdss_tracectl_b_groups[] = { + "gpio1", +}; + +static const char * const qdss_tracedata_b_groups[] = { + "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", "gpio8", "gpio9", + "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", "gpio15", "gpio16", + "gpio17", +}; + +static const char * const sdc_cmd_groups[] = { + "gpio4", +}; + +static const char * const qspi_cs_groups[] = { + "gpio4", +}; + +static const char * const sdc_clk_groups[] = { + "gpio5", +}; + +static const char * const qspi_clk_groups[] = { + "gpio5", +}; + +static const char * const sdc_rclk_groups[] = { + "gpio10", +}; + +static const char * const blsp0_spi_groups[] = { + "gpio11", "gpio12", "gpio13", "gpio14", +}; + +static const char * const blsp0_uart_groups[] = { + "gpio11", "gpio12", "gpio13", "gpio14", +}; + +static const char * const blsp3_spi_groups[] = { + "gpio15", "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21", +}; + +static const char * const blsp3_i2c_groups[] = { + "gpio15", "gpio16", +}; + +static const char * const blsp3_uart_groups[] = { + "gpio15", "gpio16", "gpio17", "gpio18", +}; + +static const char * const dbg_out_groups[] = { + "gpio17", +}; + +static const char * const cri_trng0_groups[] = { + "gpio20", "gpio38", +}; + +static const char * const cri_trng1_groups[] = { + "gpio21", "gpio34", +}; + +static const char * const pcie0_clk_groups[] = { + "gpio22", +}; + +static const char * const pta_groups[] = { + "gpio22", "gpio23", "gpio24", "gpio54", "gpio55", "gpio56", "gpio61", + "gpio62", "gpio63", +}; + +static const char * const wci21_groups[] = { + "gpio23", "gpio24", +}; + +static const char * const cxc0_groups[] = { + "gpio23", "gpio24", +}; + +static const char * const pcie0_wake_groups[] = { + "gpio24", +}; + +static const char * const qdss_cti_trig_out_b0_groups[] = { + "gpio24", +}; + +static const char * const pcie1_clk_groups[] = { + "gpio25", +}; + +static const char * const qdss_cti_trig_in_b0_groups[] = { + "gpio25", +}; + +static const char * const atest_char0_groups[] = { + "gpio26", +}; + +static const char * const qdss_cti_trig_out_b1_groups[] = { + "gpio26", +}; + +static const char * const pcie1_wake_groups[] = { + "gpio27", +}; + +static const char * const atest_char1_groups[] = { + "gpio27", +}; + +static const char * const qdss_cti_trig_in_b1_groups[] = { + "gpio27", +}; + +static const char * const pcie2_clk_groups[] = { + "gpio28", +}; + +static const char * const atest_char2_groups[] = { + "gpio28", +}; + +static const char * const atest_char3_groups[] = { + "gpio29", +}; + +static const char * const pcie2_wake_groups[] = { + "gpio30", +}; + +static const char * const pwm_groups[] = { + "gpio30", "gpio31", "gpio32", "gpio33", "gpio44", "gpio45", "gpio46", + "gpio47", "gpio50", "gpio51", "gpio52", "gpio53", "gpio54", "gpio55", + "gpio56", "gpio57", "gpio58", "gpio59", "gpio60", +}; + +static const char * const atest_char_groups[] = { + "gpio30", +}; + +static const char * const pcie3_clk_groups[] = { + "gpio31", +}; + +static const char * const qdss_cti_trig_in_a1_groups[] = { + "gpio31", +}; + +static const char * const qdss_cti_trig_out_a1_groups[] = { + "gpio32", +}; + +static const char * const pcie3_wake_groups[] = { + "gpio33", +}; + +static const char * const qdss_cti_trig_in_a0_groups[] = { + "gpio33", +}; + +static const char * const blsp2_uart_groups[] = { + "gpio34", "gpio35", +}; + +static const char * const blsp2_i2c_groups[] = { + "gpio34", "gpio35", +}; + +static const char * const blsp2_spi_groups[] = { + "gpio34", "gpio35", "gpio36", "gpio37", +}; + +static const char * const blsp1_uart_groups[] = { + "gpio34", "gpio35", "gpio36", "gpio37", +}; + +static const char * const qdss_cti_trig_out_a0_groups[] = { + "gpio34", +}; + +static const char * const cri_trng2_groups[] = { + "gpio35", +}; + +static const char * const blsp1_i2c_groups[] = { + "gpio36", "gpio37", +}; + +static const char * const cri_trng3_groups[] = { + "gpio36", +}; + +static const char * const dwc_ddrphy_groups[] = { + "gpio37", +}; + +static const char * const mdc_groups[] = { + "gpio38", +}; + +static const char * const mdio_groups[] = { + "gpio39", +}; + +static const char * const audio_pri_groups[] = { + "gpio40", "gpio41", "gpio42", "gpio43", "gpio61", "gpio61", +}; + +static const char * const audio_pdm0_groups[] = { + "gpio40", "gpio41", "gpio42", "gpio43", +}; + +static const char * const qdss_traceclk_a_groups[] = { + "gpio43", +}; + +static const char * const audio_sec_groups[] = { + "gpio44", "gpio45", "gpio46", "gpio47", "gpio62", "gpio62", +}; + +static const char * const wsa_swrm_groups[] = { + "gpio44", "gpio45", +}; + +static const char * const qdss_tracectl_a_groups[] = { + "gpio44", +}; + +static const char * const qdss_tracedata_a_groups[] = { + "gpio45", "gpio46", "gpio47", "gpio48", "gpio49", "gpio50", "gpio51", + "gpio52", "gpio53", "gpio54", "gpio55", "gpio56", "gpio57", "gpio58", + "gpio59", "gpio60", +}; + +static const char * const rx1_groups[] = { + "gpio46", +}; + +static const char * const mac_groups[] = { + "gpio46", "gpio47", "gpio57", "gpio58", +}; + +static const char * const blsp5_i2c_groups[] = { + "gpio48", "gpio49", +}; + +static const char * const blsp5_uart_groups[] = { + "gpio48", "gpio49", +}; + +static const char * const blsp4_uart_groups[] = { + "gpio50", "gpio51", "gpio52", "gpio53", +}; + +static const char * const blsp4_i2c_groups[] = { + "gpio50", "gpio51", +}; + +static const char * const blsp4_spi_groups[] = { + "gpio50", "gpio51", "gpio52", "gpio53", +}; + +static const char * const wci20_groups[] = { + "gpio57", "gpio58", +}; + +static const char * const cxc1_groups[] = { + "gpio57", "gpio58", +}; + +static const char * const rx0_groups[] = { + "gpio59", +}; + +static const char * const prng_rosc0_groups[] = { + "gpio60", +}; + +static const char * const gcc_plltest_groups[] = { + "gpio60", "gpio62", +}; + +static const char * const blsp1_spi_groups[] = { + "gpio61", "gpio62", "gpio63", "gpio64", +}; + +static const char * const audio_pdm1_groups[] = { + "gpio61", "gpio62", "gpio63", "gpio64", +}; + +static const char * const prng_rosc1_groups[] = { + "gpio61", +}; + +static const char * const gcc_tlmm_groups[] = { + "gpio61", +}; + +static const char * const prng_rosc2_groups[] = { + "gpio62", +}; + +static const char * const prng_rosc3_groups[] = { + "gpio63", +}; + +static const char * const tsens_max_groups[] = { + "gpio64", +}; + +static const struct msm_function ipq9574_functions[] = { + FUNCTION(atest_char), + FUNCTION(atest_char0), + FUNCTION(atest_char1), + FUNCTION(atest_char2), + FUNCTION(atest_char3), + FUNCTION(audio_pdm0), + FUNCTION(audio_pdm1), + FUNCTION(audio_pri), + FUNCTION(audio_sec), + FUNCTION(blsp0_spi), + FUNCTION(blsp0_uart), + FUNCTION(blsp1_i2c), + FUNCTION(blsp1_spi), + FUNCTION(blsp1_uart), + FUNCTION(blsp2_i2c), + FUNCTION(blsp2_spi), + FUNCTION(blsp2_uart), + FUNCTION(blsp3_i2c), + FUNCTION(blsp3_spi), + FUNCTION(blsp3_uart), + FUNCTION(blsp4_i2c), + FUNCTION(blsp4_spi), + FUNCTION(blsp4_uart), + FUNCTION(blsp5_i2c), + FUNCTION(blsp5_uart), + FUNCTION(cri_trng0), + FUNCTION(cri_trng1), + FUNCTION(cri_trng2), + FUNCTION(cri_trng3), + FUNCTION(cxc0), + FUNCTION(cxc1), + FUNCTION(dbg_out), + FUNCTION(dwc_ddrphy), + FUNCTION(gcc_plltest), + FUNCTION(gcc_tlmm), + FUNCTION(gpio), + FUNCTION(mac), + FUNCTION(mdc), + FUNCTION(mdio), + FUNCTION(pcie0_clk), + FUNCTION(pcie0_wake), + FUNCTION(pcie1_clk), + FUNCTION(pcie1_wake), + FUNCTION(pcie2_clk), + FUNCTION(pcie2_wake), + FUNCTION(pcie3_clk), + FUNCTION(pcie3_wake), + FUNCTION(prng_rosc0), + FUNCTION(prng_rosc1), + FUNCTION(prng_rosc2), + FUNCTION(prng_rosc3), + FUNCTION(pta), + FUNCTION(pwm), + FUNCTION(qdss_cti_trig_in_a0), + FUNCTION(qdss_cti_trig_in_a1), + FUNCTION(qdss_cti_trig_in_b0), + FUNCTION(qdss_cti_trig_in_b1), + FUNCTION(qdss_cti_trig_out_a0), + FUNCTION(qdss_cti_trig_out_a1), + FUNCTION(qdss_cti_trig_out_b0), + FUNCTION(qdss_cti_trig_out_b1), + FUNCTION(qdss_traceclk_a), + FUNCTION(qdss_traceclk_b), + FUNCTION(qdss_tracectl_a), + FUNCTION(qdss_tracectl_b), + FUNCTION(qdss_tracedata_a), + FUNCTION(qdss_tracedata_b), + FUNCTION(qspi_data), + FUNCTION(qspi_clk), + FUNCTION(qspi_cs), + FUNCTION(rx0), + FUNCTION(rx1), + FUNCTION(sdc_data), + FUNCTION(sdc_clk), + FUNCTION(sdc_cmd), + FUNCTION(sdc_rclk), + FUNCTION(tsens_max), + FUNCTION(wci20), + FUNCTION(wci21), + FUNCTION(wsa_swrm), +}; + +static const struct msm_pingroup ipq9574_groups[] = { + PINGROUP(0, sdc_data, qspi_data, qdss_traceclk_b, _, _, _, _, _, _), + PINGROUP(1, sdc_data, qspi_data, qdss_tracectl_b, _, _, _, _, _, _), + PINGROUP(2, sdc_data, qspi_data, qdss_tracedata_b, _, _, _, _, _, _), + PINGROUP(3, sdc_data, qspi_data, qdss_tracedata_b, _, _, _, _, _, _), + PINGROUP(4, sdc_cmd, qspi_cs, qdss_tracedata_b, _, _, _, _, _, _), + PINGROUP(5, sdc_clk, qspi_clk, qdss_tracedata_b, _, _, _, _, _, + _), + PINGROUP(6, sdc_data, qdss_tracedata_b, _, _, _, _, _, _, _), + PINGROUP(7, sdc_data, qdss_tracedata_b, _, _, _, _, _, _, _), + PINGROUP(8, sdc_data, qdss_tracedata_b, _, _, _, _, _, _, _), + PINGROUP(9, sdc_data, qdss_tracedata_b, _, _, _, _, _, _, _), + PINGROUP(10, sdc_rclk, qdss_tracedata_b, _, _, _, _, _, _, _), + PINGROUP(11, blsp0_spi, blsp0_uart, qdss_tracedata_b, _, _, _, _, + _, _), + PINGROUP(12, blsp0_spi, blsp0_uart, qdss_tracedata_b, _, _, _, _, + _, _), + PINGROUP(13, blsp0_spi, blsp0_uart, qdss_tracedata_b, _, _, _, _, + _, _), + PINGROUP(14, blsp0_spi, blsp0_uart, qdss_tracedata_b, _, _, _, _, + _, _), + PINGROUP(15, blsp3_spi, blsp3_i2c, blsp3_uart, qdss_tracedata_b, _, + _, _, _, _), + PINGROUP(16, blsp3_spi, blsp3_i2c, blsp3_uart, qdss_tracedata_b, _, + _, _, _, _), + PINGROUP(17, blsp3_spi, blsp3_uart, dbg_out, qdss_tracedata_b, _, _, + _, _, _), + PINGROUP(18, blsp3_spi, blsp3_uart, _, _, _, _, _, _, _), + PINGROUP(19, blsp3_spi, _, _, _, _, _, _, _, _), + PINGROUP(20, blsp3_spi, _, cri_trng0, _, _, _, _, _, _), + PINGROUP(21, blsp3_spi, _, cri_trng1, _, _, _, _, _, _), + PINGROUP(22, pcie0_clk, _, pta, _, _, _, _, _, _), + PINGROUP(23, _, pta, wci21, cxc0, _, _, _, _, _), + PINGROUP(24, pcie0_wake, _, pta, wci21, cxc0, _, + qdss_cti_trig_out_b0, _, _), + PINGROUP(25, pcie1_clk, _, _, qdss_cti_trig_in_b0, _, _, _, _, + _), + PINGROUP(26, _, atest_char0, _, qdss_cti_trig_out_b1, _, _, _, _, + _), + PINGROUP(27, pcie1_wake, _, atest_char1, qdss_cti_trig_in_b1, _, _, + _, _, _), + PINGROUP(28, pcie2_clk, atest_char2, _, _, _, _, _, _, _), + PINGROUP(29, atest_char3, _, _, _, _, _, _, _, _), + PINGROUP(30, pcie2_wake, pwm, atest_char, _, _, _, _, _, _), + PINGROUP(31, pcie3_clk, pwm, _, qdss_cti_trig_in_a1, _, _, _, _, + _), + PINGROUP(32, pwm, _, qdss_cti_trig_out_a1, _, _, _, _, _, _), + PINGROUP(33, pcie3_wake, pwm, _, qdss_cti_trig_in_a0, _, _, _, + _, _), + PINGROUP(34, blsp2_uart, blsp2_i2c, blsp2_spi, blsp1_uart, _, + cri_trng1, qdss_cti_trig_out_a0, _, _), + PINGROUP(35, blsp2_uart, blsp2_i2c, blsp2_spi, blsp1_uart, _, + cri_trng2, _, _, _), + PINGROUP(36, blsp1_uart, blsp1_i2c, blsp2_spi, _, cri_trng3, _, _, + _, _), + PINGROUP(37, blsp1_uart, blsp1_i2c, blsp2_spi, _, dwc_ddrphy, _, _, + _, _), + PINGROUP(38, mdc, _, cri_trng0, _, _, _, _, _, _), + PINGROUP(39, mdio, _, _, _, _, _, _, _, _), + PINGROUP(40, audio_pri, audio_pdm0, _, _, _, _, _, _, _), + PINGROUP(41, audio_pri, audio_pdm0, _, _, _, _, _, _, _), + PINGROUP(42, audio_pri, audio_pdm0, _, _, _, _, _, _, _), + PINGROUP(43, audio_pri, audio_pdm0, _, qdss_traceclk_a, _, _, _, + _, _), + PINGROUP(44, pwm, audio_sec, wsa_swrm, _, qdss_tracectl_a, _, _, + _, _), + PINGROUP(45, pwm, audio_sec, wsa_swrm, _, qdss_tracedata_a, _, _, + _, _), + PINGROUP(46, pwm, audio_sec, rx1, mac, _, qdss_tracedata_a, _, + _, _), + PINGROUP(47, pwm, audio_sec, mac, _, qdss_tracedata_a, _, _, _, + _), + PINGROUP(48, blsp5_i2c, blsp5_uart, _, qdss_tracedata_a, _, _, _, + _, _), + PINGROUP(49, blsp5_i2c, blsp5_uart, _, qdss_tracedata_a, _, _, _, + _, _), + PINGROUP(50, blsp4_uart, blsp4_i2c, blsp4_spi, pwm, qdss_tracedata_a, + _, _, _, _), + PINGROUP(51, blsp4_uart, blsp4_i2c, blsp4_spi, pwm, qdss_tracedata_a, + _, _, _, _), + PINGROUP(52, blsp4_uart, blsp4_spi, pwm, qdss_tracedata_a, _, _, + _, _, _), + PINGROUP(53, blsp4_uart, blsp4_spi, pwm, qdss_tracedata_a, _, _, + _, _, _), + PINGROUP(54, pta, pwm, qdss_tracedata_a, _, _, _, _, _, _), + PINGROUP(55, pta, pwm, qdss_tracedata_a, _, _, _, _, _, _), + PINGROUP(56, pta, pwm, qdss_tracedata_a, _, _, _, _, _, _), + PINGROUP(57, wci20, cxc1, mac, pwm, qdss_tracedata_a, _, _, _, + _), + PINGROUP(58, wci20, cxc1, mac, pwm, qdss_tracedata_a, _, _, _, + _), + PINGROUP(59, rx0, pwm, qdss_tracedata_a, _, _, _, _, _, _), + PINGROUP(60, pwm, prng_rosc0, qdss_tracedata_a, _, gcc_plltest, _, + _, _, _), + PINGROUP(61, blsp1_spi, audio_pri, audio_pdm1, audio_pri, pta, + prng_rosc1, gcc_tlmm, _, _), + PINGROUP(62, blsp1_spi, audio_sec, audio_pdm1, audio_sec, pta, + prng_rosc2, gcc_plltest, _, _), + PINGROUP(63, blsp1_spi, audio_pdm1, pta, prng_rosc3, _, _, _, _, + _), + PINGROUP(64, blsp1_spi, audio_pdm1, tsens_max, _, _, _, _, _, _), +}; + +/* Reserving GPIO59 for controlling the QFPROM LDO regulator */ +static const int ipq9574_reserved_gpios[] = { + 59, -1 +}; + +static const struct msm_pinctrl_soc_data ipq9574_pinctrl = { + .pins = ipq9574_pins, + .npins = ARRAY_SIZE(ipq9574_pins), + .functions = ipq9574_functions, + .nfunctions = ARRAY_SIZE(ipq9574_functions), + .groups = ipq9574_groups, + .ngroups = ARRAY_SIZE(ipq9574_groups), + .reserved_gpios = ipq9574_reserved_gpios, + .ngpios = 65, +}; + +static int ipq9574_pinctrl_probe(struct platform_device *pdev) +{ + return msm_pinctrl_probe(pdev, &ipq9574_pinctrl); +} + +static const struct of_device_id ipq9574_pinctrl_of_match[] = { + { .compatible = "qcom,ipq9574-tlmm", }, + { }, +}; + +static struct platform_driver ipq9574_pinctrl_driver = { + .driver = { + .name = "ipq9574-tlmm", + .of_match_table = ipq9574_pinctrl_of_match, + }, + .probe = ipq9574_pinctrl_probe, + .remove = msm_pinctrl_remove, +}; + +static int __init ipq9574_pinctrl_init(void) +{ + return platform_driver_register(&ipq9574_pinctrl_driver); +} +arch_initcall(ipq9574_pinctrl_init); + +static void __exit ipq9574_pinctrl_exit(void) +{ + platform_driver_unregister(&ipq9574_pinctrl_driver); +} +module_exit(ipq9574_pinctrl_exit); + +MODULE_DESCRIPTION("QTI IPQ9574 TLMM driver"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(of, ipq9574_pinctrl_of_match); -- 2.17.1 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH V3 4/7] pinctrl: qcom: Add IPQ9574 pinctrl driver 2023-01-30 12:55 ` [PATCH V3 4/7] pinctrl: qcom: Add IPQ9574 pinctrl driver devi priya @ 2023-02-08 23:14 ` Bjorn Andersson 2023-02-13 14:18 ` Devi Priya 0 siblings, 1 reply; 19+ messages in thread From: Bjorn Andersson @ 2023-02-08 23:14 UTC (permalink / raw) To: devi priya Cc: agross, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel, quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh On Mon, Jan 30, 2023 at 06:25:25PM +0530, devi priya wrote: > +static const struct msm_pingroup ipq9574_groups[] = { > + PINGROUP(0, sdc_data, qspi_data, qdss_traceclk_b, _, _, _, _, _, _), > + PINGROUP(1, sdc_data, qspi_data, qdss_tracectl_b, _, _, _, _, _, _), > + PINGROUP(2, sdc_data, qspi_data, qdss_tracedata_b, _, _, _, _, _, _), > + PINGROUP(3, sdc_data, qspi_data, qdss_tracedata_b, _, _, _, _, _, _), > + PINGROUP(4, sdc_cmd, qspi_cs, qdss_tracedata_b, _, _, _, _, _, _), > + PINGROUP(5, sdc_clk, qspi_clk, qdss_tracedata_b, _, _, _, _, _, > + _), Please avoid line wrapping these, it just makes it hard to read. [..] > +}; > + > +/* Reserving GPIO59 for controlling the QFPROM LDO regulator */ This seems like a property of the board, please use gpio-reserved-ranges in the DT node instead. Thanks, Bjorn ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3 4/7] pinctrl: qcom: Add IPQ9574 pinctrl driver 2023-02-08 23:14 ` Bjorn Andersson @ 2023-02-13 14:18 ` Devi Priya 0 siblings, 0 replies; 19+ messages in thread From: Devi Priya @ 2023-02-13 14:18 UTC (permalink / raw) To: Bjorn Andersson Cc: agross, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel, quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh Thanks Bjorn for taking time to review the patch On 2/9/2023 4:44 AM, Bjorn Andersson wrote: > On Mon, Jan 30, 2023 at 06:25:25PM +0530, devi priya wrote: >> +static const struct msm_pingroup ipq9574_groups[] = { >> + PINGROUP(0, sdc_data, qspi_data, qdss_traceclk_b, _, _, _, _, _, _), >> + PINGROUP(1, sdc_data, qspi_data, qdss_tracectl_b, _, _, _, _, _, _), >> + PINGROUP(2, sdc_data, qspi_data, qdss_tracedata_b, _, _, _, _, _, _), >> + PINGROUP(3, sdc_data, qspi_data, qdss_tracedata_b, _, _, _, _, _, _), >> + PINGROUP(4, sdc_cmd, qspi_cs, qdss_tracedata_b, _, _, _, _, _, _), >> + PINGROUP(5, sdc_clk, qspi_clk, qdss_tracedata_b, _, _, _, _, _, >> + _), > > Please avoid line wrapping these, it just makes it hard to read. Yes, we have addressed this comment part of V7 series https://lore.kernel.org/linux-arm-kernel/20230206103337.21000-5-quic_devipriy@quicinc.com/ > > [..] >> +}; >> + >> +/* Reserving GPIO59 for controlling the QFPROM LDO regulator */ > > This seems like a property of the board, please use gpio-reserved-ranges > in the DT node instead. As the GPIO is forbidden on SoC IPQ9574, we have moved it to the pinctrl driver based on the suggestions received in V1 series https://lore.kernel.org/linux-arm-kernel/675ed9f7-da31-6206-5089-1db22025ef4b@linaro.org/ > > Thanks, > Bjorn Best Regards, Devi Priya ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH V3 5/7] dt-bindings: arm: qcom: Add ipq9574 compatible 2023-01-30 12:55 [PATCH V3 0/7] Add minimal boot support for IPQ9574 devi priya ` (2 preceding siblings ...) 2023-01-30 12:55 ` [PATCH V3 4/7] pinctrl: qcom: Add IPQ9574 pinctrl driver devi priya @ 2023-01-30 12:55 ` devi priya 2023-01-31 18:11 ` Krzysztof Kozlowski 2023-01-30 12:55 ` [PATCH V3 6/7] arm64: dts: qcom: Add ipq9574 SoC and AL02 board support devi priya ` (2 subsequent siblings) 6 siblings, 1 reply; 19+ messages in thread From: devi priya @ 2023-01-30 12:55 UTC (permalink / raw) To: agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh Document the new ipq9574 SoC/board device tree bindings Signed-off-by: devi priya <quic_devipriy@quicinc.com> --- Changes in V3: - No changes Changes in V2: - Updated the ordering of the board element Documentation/devicetree/bindings/arm/qcom.yaml | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml index 22553637c519..706a8f1812b5 100644 --- a/Documentation/devicetree/bindings/arm/qcom.yaml +++ b/Documentation/devicetree/bindings/arm/qcom.yaml @@ -32,6 +32,7 @@ description: | ipq4018 ipq6018 ipq8074 + ipq9574 mdm9615 msm8226 msm8916 @@ -79,6 +80,7 @@ description: | The 'board' element must be one of the following strings: adp + ap-al02-c7 cdp cp01-c1 dragonboard @@ -329,6 +331,11 @@ properties: - qcom,ipq8074-hk10-c2 - const: qcom,ipq8074 + - items: + - enum: + - qcom,ipq9574-ap-al02-c7 + - const: qcom,ipq9574 + - description: Sierra Wireless MangOH Green with WP8548 Module items: - const: swir,mangoh-green-wp8548 -- 2.17.1 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH V3 5/7] dt-bindings: arm: qcom: Add ipq9574 compatible 2023-01-30 12:55 ` [PATCH V3 5/7] dt-bindings: arm: qcom: Add ipq9574 compatible devi priya @ 2023-01-31 18:11 ` Krzysztof Kozlowski 0 siblings, 0 replies; 19+ messages in thread From: Krzysztof Kozlowski @ 2023-01-31 18:11 UTC (permalink / raw) To: devi priya, agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh On 30/01/2023 13:55, devi priya wrote: > Document the new ipq9574 SoC/board device tree bindings > > Signed-off-by: devi priya <quic_devipriy@quicinc.com> > --- Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Best regards, Krzysztof ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH V3 6/7] arm64: dts: qcom: Add ipq9574 SoC and AL02 board support 2023-01-30 12:55 [PATCH V3 0/7] Add minimal boot support for IPQ9574 devi priya ` (3 preceding siblings ...) 2023-01-30 12:55 ` [PATCH V3 5/7] dt-bindings: arm: qcom: Add ipq9574 compatible devi priya @ 2023-01-30 12:55 ` devi priya 2023-01-30 23:55 ` Konrad Dybcio 2023-01-30 12:55 ` [PATCH V3 7/7] arm64: defconfig: Enable IPQ9574 SoC base configs devi priya 2023-01-31 18:10 ` [PATCH V3 0/7] Add minimal boot support for IPQ9574 Krzysztof Kozlowski 6 siblings, 1 reply; 19+ messages in thread From: devi priya @ 2023-01-30 12:55 UTC (permalink / raw) To: agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh Add initial device tree support for Qualcomm IPQ9574 SoC and AL02 board Co-developed-by: Anusha Rao <quic_anusha@quicinc.com> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com> Co-developed-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com> Signed-off-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com> Signed-off-by: devi priya <quic_devipriy@quicinc.com> --- Changes in V3: - Updated the order of signed-offs Changes in V2: - Updated the node name - emmc_pins to sdc_default_state - Moved the xo and sleep clock frequency to board DT - Removed the pipe clock definitions - Dropped clock frequency property for timer nodes - Added qcom,ipq9574-sdhci compatible string - Updated the copyright year to 2023 - Corrected the indentations arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 78 +++++ arch/arm64/boot/dts/qcom/ipq9574.dtsi | 285 +++++++++++++++++++ 3 files changed, 364 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts create mode 100644 arch/arm64/boot/dts/qcom/ipq9574.dtsi diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index b0423ca3e79f..ff40e86181d4 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c2.dtb +dtb-$(CONFIG_ARCH_QCOM) += ipq9574-al02-c7.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-acer-a1-724.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb diff --git a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts new file mode 100644 index 000000000000..4aa06e4f63c7 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts @@ -0,0 +1,78 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * IPQ9574 AL02-C7 board device tree source + * + * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved. + * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved. + */ + +/dts-v1/; + +#include "ipq9574.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C7"; + compatible = "qcom,ipq9574-ap-al02-c7", "qcom,ipq9574"; + + aliases { + serial0 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&blsp1_uart2 { + pinctrl-0 = <&uart2_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&sdhc_1 { + pinctrl-0 = <&sdc_default_state>; + pinctrl-names = "default"; + status = "okay"; +}; + +&sleep_clk { + clock-frequency = <32000>; +}; + +&tlmm { + sdc_default_state: sdc-default-state { + clk-pins { + pins = "gpio5"; + function = "sdc_clk"; + drive-strength = <8>; + bias-disable; + }; + + cmd-pins { + pins = "gpio4"; + function = "sdc_cmd"; + drive-strength = <8>; + bias-pull-up; + }; + + data-pins { + pins = "gpio0", "gpio1", "gpio2", + "gpio3", "gpio6", "gpio7", + "gpio8", "gpio9"; + function = "sdc_data"; + drive-strength = <8>; + bias-pull-up; + }; + + rclk-pins { + pins = "gpio10"; + function = "sdc_rclk"; + drive-strength = <8>; + bias-pull-down; + }; + }; +}; + +&xo_board_clk { + clock-frequency = <24000000>; +}; diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi new file mode 100644 index 000000000000..1f34ebc8724f --- /dev/null +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi @@ -0,0 +1,285 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * IPQ9574 SoC device tree source + * + * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved. + * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved. + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/qcom,ipq9574-gcc.h> +#include <dt-bindings/reset/qcom,ipq9574-gcc.h> + +/ { + interrupt-parent = <&intc>; + #address-cells = <2>; + #size-cells = <2>; + + clocks { + bias_pll_ubi_nc_clk: bias-pll-ubi-nc-clk { + compatible = "fixed-clock"; + clock-frequency = <353000000>; + #clock-cells = <0>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + + xo_board_clk: xo-board-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a73"; + reg = <0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a73"; + reg = <0x1>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + CPU2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a73"; + reg = <0x2>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + CPU3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a73"; + reg = <0x3>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + L2_0: l2-cache { + compatible = "cache"; + cache-level = <2>; + }; + }; + + memory@40000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0x0 0x40000000 0x0 0x0>; + }; + + pmu { + compatible = "arm,cortex-a73-pmu"; + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + tz_region: memory@4a600000 { + reg = <0x0 0x4a600000 0x0 0x400000>; + no-map; + }; + }; + + soc: soc@0 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0xffffffff>; + compatible = "simple-bus"; + + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq9574-tlmm"; + reg = <0x01000000 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 65>; + gpio-reserved-ranges = <59 1>; + interrupt-controller; + #interrupt-cells = <2>; + + uart2_pins: uart2-state { + pins = "gpio34", "gpio35"; + function = "blsp2_uart"; + drive-strength = <8>; + bias-disable; + }; + }; + + gcc: clock-controller@1800000 { + compatible = "qcom,ipq9574-gcc"; + reg = <0x01800000 0x80000>; + clocks = <&xo_board_clk>, + <&sleep_clk>, + <&bias_pll_ubi_nc_clk>, + <0>, + <0>, + <0>, + <0>, + <0>; + clock-names = "xo", + "sleep_clk", + "bias_pll_ubi_nc_clk", + "pcie30_phy0_pipe_clk", + "pcie30_phy1_pipe_clk", + "pcie30_phy2_pipe_clk", + "pcie30_phy3_pipe_clk", + "usb3phy_0_cc_pipe_clk"; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; + + sdhc_1: mmc@7804000 { + compatible = "qcom,ipq9574-sdhci", "qcom,sdhci-msm-v5"; + reg = <0x07804000 0x1000>, <0x07805000 0x1000>; + reg-names = "hc", "cqhci"; + + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC1_AHB_CLK>, + <&gcc GCC_SDCC1_APPS_CLK>, + <&xo_board_clk>; + clock-names = "iface", "core", "xo"; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + max-frequency = <384000000>; + bus-width = <8>; + non-removable; + status = "disabled"; + }; + + blsp1_uart2: serial@78b1000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x078b1000 0x200>; + interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + + intc: interrupt-controller@b000000 { + compatible = "qcom,msm-qgic2"; + reg = <0x0b000000 0x1000>, /* GICD */ + <0x0b002000 0x1000>, /* GICC */ + <0x0b001000 0x1000>, /* GICH */ + <0x0b004000 0x1000>; /* GICV */ + #address-cells = <1>; + #size-cells = <1>; + interrupt-controller; + #interrupt-cells = <3>; + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + ranges = <0 0x0b00c000 0x3000>; + + v2m0: v2m@0 { + compatible = "arm,gic-v2m-frame"; + reg = <0x0 0xffd>; + msi-controller; + }; + + v2m1: v2m@1 { + compatible = "arm,gic-v2m-frame"; + reg = <0x00001000 0xffd>; + msi-controller; + }; + + v2m2: v2m@2 { + compatible = "arm,gic-v2m-frame"; + reg = <0x00002000 0xffd>; + msi-controller; + }; + }; + + timer@b120000 { + compatible = "arm,armv7-timer-mem"; + reg = <0x0b120000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + frame@b120000 { + reg = <0x0b121000 0x1000>, + <0x0b122000 0x1000>; + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + }; + + frame@b123000 { + reg = <0x0b123000 0x1000>; + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + frame@b124000 { + reg = <0x0b124000 0x1000>; + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + frame@b125000 { + reg = <0x0b125000 0x1000>; + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + frame@b126000 { + reg = <0x0b126000 0x1000>; + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + frame@b127000 { + reg = <0x0b127000 0x1000>; + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + frame@b128000 { + reg = <0x0b128000 0x1000>; + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; +}; -- 2.17.1 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH V3 6/7] arm64: dts: qcom: Add ipq9574 SoC and AL02 board support 2023-01-30 12:55 ` [PATCH V3 6/7] arm64: dts: qcom: Add ipq9574 SoC and AL02 board support devi priya @ 2023-01-30 23:55 ` Konrad Dybcio 2023-01-31 10:41 ` Devi Priya 0 siblings, 1 reply; 19+ messages in thread From: Konrad Dybcio @ 2023-01-30 23:55 UTC (permalink / raw) To: devi priya, agross, andersson, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh On 30.01.2023 13:55, devi priya wrote: > Add initial device tree support for Qualcomm IPQ9574 SoC > and AL02 board > > Co-developed-by: Anusha Rao <quic_anusha@quicinc.com> > Signed-off-by: Anusha Rao <quic_anusha@quicinc.com> > Co-developed-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com> > Signed-off-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com> > Signed-off-by: devi priya <quic_devipriy@quicinc.com> > --- > Changes in V3: > - Updated the order of signed-offs > > Changes in V2: > - Updated the node name - emmc_pins to sdc_default_state > - Moved the xo and sleep clock frequency to board DT > - Removed the pipe clock definitions > - Dropped clock frequency property for timer nodes > - Added qcom,ipq9574-sdhci compatible string > - Updated the copyright year to 2023 > - Corrected the indentations > > arch/arm64/boot/dts/qcom/Makefile | 1 + > arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 78 +++++ > arch/arm64/boot/dts/qcom/ipq9574.dtsi | 285 +++++++++++++++++++ > 3 files changed, 364 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts > create mode 100644 arch/arm64/boot/dts/qcom/ipq9574.dtsi > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index b0423ca3e79f..ff40e86181d4 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c2.dtb > +dtb-$(CONFIG_ARCH_QCOM) += ipq9574-al02-c7.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-acer-a1-724.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb > diff --git a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts > new file mode 100644 > index 000000000000..4aa06e4f63c7 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts > @@ -0,0 +1,78 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) > +/* > + * IPQ9574 AL02-C7 board device tree source > + * > + * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved. > + * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved. > + */ > + > +/dts-v1/; > + > +#include "ipq9574.dtsi" > + > +/ { > + model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C7"; > + compatible = "qcom,ipq9574-ap-al02-c7", "qcom,ipq9574"; > + > + aliases { > + serial0 = &blsp1_uart2; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > +}; > + > +&blsp1_uart2 { > + pinctrl-0 = <&uart2_pins>; > + pinctrl-names = "default"; > + status = "okay"; > +}; > + > +&sdhc_1 { > + pinctrl-0 = <&sdc_default_state>; > + pinctrl-names = "default"; > + status = "okay"; > +}; > + > +&sleep_clk { > + clock-frequency = <32000>; > +}; > + > +&tlmm { > + sdc_default_state: sdc-default-state { > + clk-pins { > + pins = "gpio5"; > + function = "sdc_clk"; > + drive-strength = <8>; > + bias-disable; > + }; > + > + cmd-pins { > + pins = "gpio4"; > + function = "sdc_cmd"; > + drive-strength = <8>; > + bias-pull-up; > + }; > + > + data-pins { > + pins = "gpio0", "gpio1", "gpio2", > + "gpio3", "gpio6", "gpio7", > + "gpio8", "gpio9"; The second and third rows are still incorrectly indented. > + function = "sdc_data"; > + drive-strength = <8>; > + bias-pull-up; > + }; > + > + rclk-pins { > + pins = "gpio10"; > + function = "sdc_rclk"; > + drive-strength = <8>; > + bias-pull-down; > + }; > + }; [...] > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + tz_region: memory@4a600000 { tz@ > + reg = <0x0 0x4a600000 0x0 0x400000>; > + no-map; > + }; > + }; > + > + soc: soc@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0 0 0 0xffffffff>; > + compatible = "simple-bus"; compatible first, please > + > + tlmm: pinctrl@1000000 { > + compatible = "qcom,ipq9574-tlmm"; > + reg = <0x01000000 0x300000>; > + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&tlmm 0 0 65>; > + gpio-reserved-ranges = <59 1>; It's reserved in the pinctrl driver, no need to do it again here. > + interrupt-controller; > + #interrupt-cells = <2>; > + > + uart2_pins: uart2-state { > + pins = "gpio34", "gpio35"; [...] > + > + intc: interrupt-controller@b000000 { > + compatible = "qcom,msm-qgic2"; > + reg = <0x0b000000 0x1000>, /* GICD */ > + <0x0b002000 0x1000>, /* GICC */ > + <0x0b001000 0x1000>, /* GICH */ > + <0x0b004000 0x1000>; /* GICV */ > + #address-cells = <1>; > + #size-cells = <1>; > + interrupt-controller; > + #interrupt-cells = <3>; > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; > + ranges = <0 0x0b00c000 0x3000>; > + > + v2m0: v2m@0 { > + compatible = "arm,gic-v2m-frame"; > + reg = <0x0 0xffd>; > + msi-controller; > + }; > + > + v2m1: v2m@1 { > + compatible = "arm,gic-v2m-frame"; > + reg = <0x00001000 0xffd>; Unit address must match the address part of the reg property. > + msi-controller; > + }; > + > + v2m2: v2m@2 { And here. Konrad > + compatible = "arm,gic-v2m-frame"; > + reg = <0x00002000 0xffd>; > + msi-controller; > + }; > + }; > + > + timer@b120000 { > + compatible = "arm,armv7-timer-mem"; > + reg = <0x0b120000 0x1000>; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + frame@b120000 { > + reg = <0x0b121000 0x1000>, > + <0x0b122000 0x1000>; > + frame-number = <0>; > + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > + frame@b123000 { > + reg = <0x0b123000 0x1000>; > + frame-number = <1>; > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > + status = "disabled"; > + }; > + > + frame@b124000 { > + reg = <0x0b124000 0x1000>; > + frame-number = <2>; > + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; > + status = "disabled"; > + }; > + > + frame@b125000 { > + reg = <0x0b125000 0x1000>; > + frame-number = <3>; > + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; > + status = "disabled"; > + }; > + > + frame@b126000 { > + reg = <0x0b126000 0x1000>; > + frame-number = <4>; > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > + status = "disabled"; > + }; > + > + frame@b127000 { > + reg = <0x0b127000 0x1000>; > + frame-number = <5>; > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > + status = "disabled"; > + }; > + > + frame@b128000 { > + reg = <0x0b128000 0x1000>; > + frame-number = <6>; > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; > + status = "disabled"; > + }; > + }; > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; > + }; > +}; ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH V3 6/7] arm64: dts: qcom: Add ipq9574 SoC and AL02 board support 2023-01-30 23:55 ` Konrad Dybcio @ 2023-01-31 10:41 ` Devi Priya 0 siblings, 0 replies; 19+ messages in thread From: Devi Priya @ 2023-01-31 10:41 UTC (permalink / raw) To: Konrad Dybcio, agross, andersson, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh On 1/31/2023 5:25 AM, Konrad Dybcio wrote: > > > On 30.01.2023 13:55, devi priya wrote: >> Add initial device tree support for Qualcomm IPQ9574 SoC >> and AL02 board >> >> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com> >> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com> >> Co-developed-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com> >> Signed-off-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com> >> Signed-off-by: devi priya <quic_devipriy@quicinc.com> >> --- >> Changes in V3: >> - Updated the order of signed-offs >> >> Changes in V2: >> - Updated the node name - emmc_pins to sdc_default_state >> - Moved the xo and sleep clock frequency to board DT >> - Removed the pipe clock definitions >> - Dropped clock frequency property for timer nodes >> - Added qcom,ipq9574-sdhci compatible string >> - Updated the copyright year to 2023 >> - Corrected the indentations >> >> arch/arm64/boot/dts/qcom/Makefile | 1 + >> arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 78 +++++ >> arch/arm64/boot/dts/qcom/ipq9574.dtsi | 285 +++++++++++++++++++ >> 3 files changed, 364 insertions(+) >> create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts >> create mode 100644 arch/arm64/boot/dts/qcom/ipq9574.dtsi >> >> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile >> index b0423ca3e79f..ff40e86181d4 100644 >> --- a/arch/arm64/boot/dts/qcom/Makefile >> +++ b/arch/arm64/boot/dts/qcom/Makefile >> @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb >> dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb >> dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb >> dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c2.dtb >> +dtb-$(CONFIG_ARCH_QCOM) += ipq9574-al02-c7.dtb >> dtb-$(CONFIG_ARCH_QCOM) += msm8916-acer-a1-724.dtb >> dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb >> dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb >> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts >> new file mode 100644 >> index 000000000000..4aa06e4f63c7 >> --- /dev/null >> +++ b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts >> @@ -0,0 +1,78 @@ >> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) >> +/* >> + * IPQ9574 AL02-C7 board device tree source >> + * >> + * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved. >> + * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved. >> + */ >> + >> +/dts-v1/; >> + >> +#include "ipq9574.dtsi" >> + >> +/ { >> + model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C7"; >> + compatible = "qcom,ipq9574-ap-al02-c7", "qcom,ipq9574"; >> + >> + aliases { >> + serial0 = &blsp1_uart2; >> + }; >> + >> + chosen { >> + stdout-path = "serial0:115200n8"; >> + }; >> +}; >> + >> +&blsp1_uart2 { >> + pinctrl-0 = <&uart2_pins>; >> + pinctrl-names = "default"; >> + status = "okay"; >> +}; >> + >> +&sdhc_1 { >> + pinctrl-0 = <&sdc_default_state>; >> + pinctrl-names = "default"; >> + status = "okay"; >> +}; >> + >> +&sleep_clk { >> + clock-frequency = <32000>; >> +}; >> + >> +&tlmm { >> + sdc_default_state: sdc-default-state { >> + clk-pins { >> + pins = "gpio5"; >> + function = "sdc_clk"; >> + drive-strength = <8>; >> + bias-disable; >> + }; >> + >> + cmd-pins { >> + pins = "gpio4"; >> + function = "sdc_cmd"; >> + drive-strength = <8>; >> + bias-pull-up; >> + }; >> + >> + data-pins { >> + pins = "gpio0", "gpio1", "gpio2", >> + "gpio3", "gpio6", "gpio7", >> + "gpio8", "gpio9"; > The second and third rows are still incorrectly indented. okay. will correct it. > >> + function = "sdc_data"; >> + drive-strength = <8>; >> + bias-pull-up; >> + }; >> + >> + rclk-pins { >> + pins = "gpio10"; >> + function = "sdc_rclk"; >> + drive-strength = <8>; >> + bias-pull-down; >> + }; >> + }; > > [...] > >> + reserved-memory { >> + #address-cells = <2>; >> + #size-cells = <2>; >> + ranges; >> + >> + tz_region: memory@4a600000 { > tz@ > Sure >> + reg = <0x0 0x4a600000 0x0 0x400000>; >> + no-map; >> + }; >> + }; >> + >> + soc: soc@0 { >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges = <0 0 0 0xffffffff>; >> + compatible = "simple-bus"; > compatible first, please > Sure, okay >> + >> + tlmm: pinctrl@1000000 { >> + compatible = "qcom,ipq9574-tlmm"; >> + reg = <0x01000000 0x300000>; >> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; >> + gpio-controller; >> + #gpio-cells = <2>; >> + gpio-ranges = <&tlmm 0 0 65>; >> + gpio-reserved-ranges = <59 1>; > It's reserved in the pinctrl driver, no need to do it again here. > Okay, got it. > >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + >> + uart2_pins: uart2-state { >> + pins = "gpio34", "gpio35"; > > [...] > >> + >> + intc: interrupt-controller@b000000 { >> + compatible = "qcom,msm-qgic2"; >> + reg = <0x0b000000 0x1000>, /* GICD */ >> + <0x0b002000 0x1000>, /* GICC */ >> + <0x0b001000 0x1000>, /* GICH */ >> + <0x0b004000 0x1000>; /* GICV */ >> + #address-cells = <1>; >> + #size-cells = <1>; >> + interrupt-controller; >> + #interrupt-cells = <3>; >> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; >> + ranges = <0 0x0b00c000 0x3000>; >> + >> + v2m0: v2m@0 { >> + compatible = "arm,gic-v2m-frame"; >> + reg = <0x0 0xffd>; >> + msi-controller; >> + }; >> + >> + v2m1: v2m@1 { >> + compatible = "arm,gic-v2m-frame"; >> + reg = <0x00001000 0xffd>; > Unit address must match the address part of the reg property. > Okay >> + msi-controller; >> + }; >> + >> + v2m2: v2m@2 { > And here. > Okay > Konrad >> + compatible = "arm,gic-v2m-frame"; >> + reg = <0x00002000 0xffd>; >> + msi-controller; >> + }; >> + }; >> + >> + timer@b120000 { >> + compatible = "arm,armv7-timer-mem"; >> + reg = <0x0b120000 0x1000>; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + >> + frame@b120000 { >> + reg = <0x0b121000 0x1000>, >> + <0x0b122000 0x1000>; >> + frame-number = <0>; >> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; >> + }; >> + >> + frame@b123000 { >> + reg = <0x0b123000 0x1000>; >> + frame-number = <1>; >> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; >> + status = "disabled"; >> + }; >> + >> + frame@b124000 { >> + reg = <0x0b124000 0x1000>; >> + frame-number = <2>; >> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; >> + status = "disabled"; >> + }; >> + >> + frame@b125000 { >> + reg = <0x0b125000 0x1000>; >> + frame-number = <3>; >> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; >> + status = "disabled"; >> + }; >> + >> + frame@b126000 { >> + reg = <0x0b126000 0x1000>; >> + frame-number = <4>; >> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; >> + status = "disabled"; >> + }; >> + >> + frame@b127000 { >> + reg = <0x0b127000 0x1000>; >> + frame-number = <5>; >> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; >> + status = "disabled"; >> + }; >> + >> + frame@b128000 { >> + reg = <0x0b128000 0x1000>; >> + frame-number = <6>; >> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; >> + status = "disabled"; >> + }; >> + }; >> + }; >> + >> + timer { >> + compatible = "arm,armv8-timer"; >> + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, >> + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, >> + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, >> + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; >> + }; >> +}; Best Regards, Devi Priya ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH V3 7/7] arm64: defconfig: Enable IPQ9574 SoC base configs 2023-01-30 12:55 [PATCH V3 0/7] Add minimal boot support for IPQ9574 devi priya ` (4 preceding siblings ...) 2023-01-30 12:55 ` [PATCH V3 6/7] arm64: dts: qcom: Add ipq9574 SoC and AL02 board support devi priya @ 2023-01-30 12:55 ` devi priya 2023-01-31 18:10 ` [PATCH V3 0/7] Add minimal boot support for IPQ9574 Krzysztof Kozlowski 6 siblings, 0 replies; 19+ messages in thread From: devi priya @ 2023-01-30 12:55 UTC (permalink / raw) To: agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh Enables clk & pinctrl related configs Signed-off-by: devi priya <quic_devipriy@quicinc.com> --- Changes in V2 & V3: - No changes arch/arm64/configs/defconfig | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index 984553d55e17..5d6a54deef02 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -550,6 +550,7 @@ CONFIG_PINCTRL_IMX93=y CONFIG_PINCTRL_MSM=y CONFIG_PINCTRL_IPQ8074=y CONFIG_PINCTRL_IPQ6018=y +CONFIG_PINCTRL_IPQ9574=y CONFIG_PINCTRL_MSM8916=y CONFIG_PINCTRL_MSM8953=y CONFIG_PINCTRL_MSM8976=y @@ -1107,6 +1108,7 @@ CONFIG_QCOM_CLK_SMD_RPM=y CONFIG_QCOM_CLK_RPMH=y CONFIG_IPQ_GCC_6018=y CONFIG_IPQ_GCC_8074=y +CONFIG_IPQ_GCC_9574=y CONFIG_MSM_GCC_8916=y CONFIG_MSM_GCC_8994=y CONFIG_MSM_MMCC_8996=y -- 2.17.1 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH V3 0/7] Add minimal boot support for IPQ9574 2023-01-30 12:55 [PATCH V3 0/7] Add minimal boot support for IPQ9574 devi priya ` (5 preceding siblings ...) 2023-01-30 12:55 ` [PATCH V3 7/7] arm64: defconfig: Enable IPQ9574 SoC base configs devi priya @ 2023-01-31 18:10 ` Krzysztof Kozlowski 6 siblings, 0 replies; 19+ messages in thread From: Krzysztof Kozlowski @ 2023-01-31 18:10 UTC (permalink / raw) To: devi priya, agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt, mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel, shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, nfraprado, linux-arm-msm, devicetree, linux-kernel, linux-clk, linux-gpio, linux-arm-kernel Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav, quic_arajkuma, quic_anusha, quic_poovendh On 30/01/2023 13:55, devi priya wrote: > The IPQ9574 is Qualcomm's 802.11ax SoC for Routers, > Gateways and Access Points. > > This series adds minimal board boot support for ipq9574-al02-c7 board > > Posting V3 series, considering the previously posted version as V2 > > Changes in V3: > - Rebased on linux-next/master > - Dropped the 'dt-bindings: mmc: sdhci-msm: Document the IPQ9574 > compatible' since it is already part of the linux-next/master > - Detailed change log is added in the respective patches > - V2 can be found at > https://lore.kernel.org/linux-arm-msm/f81e4605-9111-7f70-abb3-72067d68f8e2@quicinc.com/ This was v1. :) Best regards, Krzysztof ^ permalink raw reply [flat|nested] 19+ messages in thread
end of thread, other threads:[~2023-02-14 3:16 UTC | newest] Thread overview: 19+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2023-01-30 12:55 [PATCH V3 0/7] Add minimal boot support for IPQ9574 devi priya 2023-01-30 12:55 ` [PATCH V3 1/7] dt-bindings: Add ipq9574 clock and reset definitions devi priya 2023-01-31 18:16 ` Krzysztof Kozlowski 2023-01-31 21:13 ` Stephen Boyd 2023-02-08 23:11 ` Bjorn Andersson 2023-02-13 14:27 ` Devi Priya 2023-02-14 3:14 ` Devi Priya 2023-01-30 12:55 ` [PATCH V3 3/7] dt-bindings: pinctrl: qcom: Add support for IPQ9574 devi priya 2023-01-31 18:12 ` Krzysztof Kozlowski 2023-01-30 12:55 ` [PATCH V3 4/7] pinctrl: qcom: Add IPQ9574 pinctrl driver devi priya 2023-02-08 23:14 ` Bjorn Andersson 2023-02-13 14:18 ` Devi Priya 2023-01-30 12:55 ` [PATCH V3 5/7] dt-bindings: arm: qcom: Add ipq9574 compatible devi priya 2023-01-31 18:11 ` Krzysztof Kozlowski 2023-01-30 12:55 ` [PATCH V3 6/7] arm64: dts: qcom: Add ipq9574 SoC and AL02 board support devi priya 2023-01-30 23:55 ` Konrad Dybcio 2023-01-31 10:41 ` Devi Priya 2023-01-30 12:55 ` [PATCH V3 7/7] arm64: defconfig: Enable IPQ9574 SoC base configs devi priya 2023-01-31 18:10 ` [PATCH V3 0/7] Add minimal boot support for IPQ9574 Krzysztof Kozlowski
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).