[PATCH v3 0/2] add device Xiaomi Mi 6 (codename sagit) and board binding

[PATCH v3 0/2] add device Xiaomi Mi 6 (codename sagit) and board binding

[Dzmitry Sankouski]

Add initial support for Xiaomi Mi 6 phone (codename sagit)

Dzmitry Sankouski (2):
  arm64: dts: qcom: sagit: add initial device tree for sagit
  dt-bindings: arm: add xiaomi,sagit board based on msm8998 chip

 .../devicetree/bindings/arm/qcom.yaml         |   1 +
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../boot/dts/qcom/msm8998-xiaomi-sagit.dts    | 689 ++++++++++++++++++
 arch/arm64/boot/dts/qcom/pm8998.dtsi          |   6 +
 4 files changed, 697 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts

-- 
2.30.2

[PATCH v3 1/2] arm64: dts: qcom: sagit: add initial device tree for sagit

[Dzmitry Sankouski]

New device support - Xiaomi Mi6 phone

What works:
- storage
- usb
- power regulators

Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
---
Changes for v3:
- regulators nodes renamed to match pattern 'regulators-[01]'
- duplicate cci1-default node deleted
- add state suffix to pinctrl

 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../boot/dts/qcom/msm8998-xiaomi-sagit.dts    | 689 ++++++++++++++++++
 arch/arm64/boot/dts/qcom/pm8998.dtsi          |   6 +
 3 files changed, 696 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 1d86a33de528..0460aabf1b59 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -46,6 +46,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-oneplus-dumpling.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-lilac.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-maple.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-poplar.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-xiaomi-sagit.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qrb5165-rb5.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
new file mode 100644
index 000000000000..871492d44df5
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
@@ -0,0 +1,689 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Xiaomi Mi 6 (sagit) device tree source based on msm8998-mtp.dtsi
+ *
+ * Copyright (c) 2022, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Degdag Mohamed <degdagmohamed@gmail.com>
+ * Copyright (c) 2022, Dzmitry Sankouski <dsankouski@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "msm8998.dtsi"
+#include "pm8005.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/*
+ * Delete following upstream (msm8998.dtsi) reserved
+ * memory mappings which are different in this device.
+ */
+/delete-node/ &mpss_mem;
+/delete-node/ &venus_mem;
+/delete-node/ &mba_mem;
+/delete-node/ &slpi_mem;
+/delete-node/ &ipa_fw_mem;
+/delete-node/ &ipa_gsi_mem;
+/delete-node/ &gpu_mem;
+/delete-node/ &wlan_msa_mem;
+
+/ {
+	model = "Xiaomi Mi 6";
+	compatible = "xiaomi,sagit", "qcom,msm8998";
+	chassis-type = "handset";
+	/* Required for bootloader to select correct board */
+	qcom,board-id = <30 0>;
+
+	reserved-memory {
+		/*
+		 * The following memory regions on downstream are "dynamically allocated"
+		 * but given the same addresses every time. Hard code them as these addresses
+		 * are where the Xiaomi signed firmware expects them to be.
+		 */
+		ipa_fws_region: ipa@f7800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0xf7800000 0x0 0x5000>;
+			no-map;
+		};
+
+		zap_shader_region: gpu@f7900000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0xf7900000 0x0 0x2000>;
+			no-map;
+		};
+
+		mpss_mem: memory@8d000000 {
+			reg = <0x0 0x8d000000 0x0 0x7000000>;
+			no-map;
+		};
+
+		venus_mem: memory@94000000 {
+			reg = <0x0 0x94000000 0x0 0x500000>;
+			no-map;
+		};
+
+		mba_mem: memory@94500000 {
+			reg = <0x0 0x94500000 0x0 0x200000>;
+			no-map;
+		};
+
+		slpi_mem: memory@94700000 {
+			reg = <0x0 0x94700000 0x0 0x10000>;
+			no-map;
+		};
+
+		ipa_fw_mem: memory@95600000 {
+			reg = <0x0 0x95600000 0x0 0x10000>;
+			no-map;
+		};
+
+		ipa_gsi_mem: memory@95610000 {
+			reg = <0x0 0x95610000 0x0 0x5000>;
+			no-map;
+		};
+
+		gpu_mem: memory@95615000 {
+			reg = <0x0 0x95615000 0x0 0x100000>;
+			no-map;
+		};
+
+		wlan_msa_mem: memory@95715000 {
+			reg = <0x0 0x95715000 0x0 0x100000>;
+			no-map;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		label = "Volume buttons";
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vol_up_key_default>;
+
+		key-vol-up {
+			label = "Volume up";
+			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+			wakeup-source;
+		};
+	};
+
+	gpio-hall-sensor {
+		compatible = "gpio-keys";
+		label = "Hall effect sensor";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&hall_sensor_default>;
+
+		event-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	disp_vddts_vreg: disp-vddts-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "disp-vddts-regulator";
+		gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&blsp1_i2c5 {
+	pinctrl-names = "default", "sleep";
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&ts_active>;
+		pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
+
+		vdd-supply = <&disp_vddts_vreg>;
+		vio-supply = <&vreg_l6a_1p8>;
+
+		syna,reset-delay-ms = <20>;
+		syna,startup-delay-ms = <20>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			touchscreen-x-mm = <64>;
+			touchscreen-y-mm = <114>;
+			syna,sensor-type = <1>;
+			syna,rezero-wait-ms = <20>;
+		};
+
+		rmi4-f1a@1a {
+			reg = <0x1a>;
+			syna,codes = <KEY_BACK KEY_APPSELECT>;
+		};
+	};
+};
+
+&blsp1_i2c5_sleep {
+	/delete-property/ bias-pull-up;
+	bias-disable;
+};
+
+&blsp1_uart3 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&blsp1_uart3_on {
+	rx {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-up on 46 (RX). This is needed to
+		 * avoid garbage data when the TX pin of the Bluetooth
+		 * module is in tri-state (module powered off or not
+		 * driving the signal yet).
+		 */
+		bias-pull-up;
+	};
+
+	cts {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-down on 47 (CTS) to match the pull
+		 * of the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+};
+
+&blsp2_uart1 {
+	status = "okay";
+};
+
+&pm8005_lsid1 {
+	regulators-0 {
+		compatible = "qcom,pm8005-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+
+		pm8005_s1: s1 { /* VDD_GFX supply */
+			regulator-min-microvolt = <524000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-enable-ramp-delay = <500>;
+
+			/* hack until we rig up the gpu consumer */
+			regulator-always-on;
+		};
+	};
+};
+
+&pm8998_gpio {
+	vol_up_key_default: vol-up-key-default-state {
+		pins = "gpio6";
+		function = "normal";
+		bias-pull-up;
+		input-enable;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+	};
+
+	audio_mclk_pin: audio-mclk-pin-active-state {
+		pins = "gpio13";
+		function = "func2";
+		power-source = <0>;
+	};
+};
+
+&qusb2phy {
+	status = "okay";
+
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8998-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+		vdd_s7-supply = <&vph_pwr>;
+		vdd_s8-supply = <&vph_pwr>;
+		vdd_s9-supply = <&vph_pwr>;
+		vdd_s10-supply = <&vph_pwr>;
+		vdd_s11-supply = <&vph_pwr>;
+		vdd_s12-supply = <&vph_pwr>;
+		vdd_s13-supply = <&vph_pwr>;
+		vdd_l1_l27-supply = <&vreg_s7a_1p025>;
+		vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
+		vdd_l3_l11-supply = <&vreg_s7a_1p025>;
+		vdd_l4_l5-supply = <&vreg_s7a_1p025>;
+		vdd_l6-supply = <&vreg_s5a_2p04>;
+		vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
+		vdd_l9-supply = <&vreg_bob>;
+		vdd_l10_l23_l25-supply = <&vreg_bob>;
+		vdd_l13_l19_l21-supply = <&vreg_bob>;
+		vdd_l16_l28-supply = <&vreg_bob>;
+		vdd_l18_l22-supply = <&vreg_bob>;
+		vdd_l20_l24-supply = <&vreg_bob>;
+		vdd_l26-supply = <&vreg_s3a_1p35>;
+		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s3a_1p35: s3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_s4a_1p8: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_s5a_2p04: s5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_s7a_1p025: s7 {
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1028000>;
+		};
+
+		vreg_l1a_0p875: l1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+		};
+
+		vreg_l2a_1p2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l3a_1p0: l3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_l5a_0p8: l5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		vreg_l6a_1p8: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l7a_1p8: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l8a_1p2: l8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l9a_1p8: l9 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l10a_1p8: l10 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l11a_1p0: l11 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_l12a_1p8: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l13a_2p95: l13 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l14a_1p8: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l15a_1p8: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l16a_2p7: l16 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+		};
+
+		vreg_l17a_1p3: l17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+		};
+
+		vreg_l18a_2p7: l18 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+		};
+
+		vreg_l19a_3p0: l19 {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+		};
+
+		vreg_l20a_2p95: l20 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l21a_2p95: l21 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-system-load = <800000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l22a_2p85: l22 {
+			regulator-min-microvolt = <2864000>;
+			regulator-max-microvolt = <2864000>;
+		};
+
+		vreg_l23a_3p3: l23 {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3312000>;
+		};
+
+		vreg_l24a_3p075: l24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+		};
+
+		vreg_l25a_3p3: l25 {
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3312000>;
+		};
+
+		vreg_l26a_1p2: l26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l28_3p0: l28 {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+		};
+
+		vreg_lvs1a_1p8: lvs1 { };
+
+		vreg_lvs2a_1p8: lvs2 { };
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pmi8998-regulators";
+
+		vdd_bob-supply = <&vph_pwr>;
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3600000>;
+		};
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	cci1_default_state: cci1-default-state {
+		pins = "gpio19", "gpio20";
+		function = "cci_i2c";
+		bias-disable;
+		drive-strength = <2>;
+	};
+
+	cdc_reset_n: cdc-reset-n {
+		pins = "gpio64";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <16>;
+		output-high;
+	};
+
+	hall_sensor_default_state: hall-sensor-default-state {
+		pins = "gpio124";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		input-enable;
+	};
+
+	mdss_dsi_active_state: mdss-dsi-active-state {
+		pins = "gpio94";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	mdss_dsi_suspend_state: mdss-dsi-suspend-state {
+		pins = "gpio94";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdss_te_active_state: mdss-te-active-state {
+		pins = "gpio10";
+		function = "mdp_vsync_a";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdss_te_suspend_state: mdss-te-suspend-state {
+		pins = "gpio10";
+		function = "mdp_vsync_a";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	msm_mclk0_active_state: msm-mclk0-active-state {
+		pins = "gpio13";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	msm_mclk0_suspend_state: msm-mclk0-suspend-state {
+		pins = "gpio13";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	msm_mclk1_active_state: msm-mclk1-active-state {
+		pins = "gpio14";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	msm_mclk1_suspend_state: msm-mclk1-suspend-state {
+		pins = "gpio14";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	nfc_int_active_state: nfc-int-active-state {
+		pins = "gpio92";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-pull-up;
+	};
+
+	nfc_int_suspend_state: nfc-int-suspend-state {
+		pins = "gpio92";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-pull-up;
+	};
+
+	nfc_enable_active_state: nfc-enable-active-state {
+		pins = "gpio12", "gpio116";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-pull-up;
+	};
+
+	nfc_enable_suspend_state: nfc-enable-suspend-state {
+		pins = "gpio12", "gpio116";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-disable;
+	};
+
+	ts_active_state: ts-active-state {
+		pins = "gpio89", "gpio125";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-pull-up;
+		input-enable;
+	};
+
+	ts_int_suspend_state: ts-int-suspend-state {
+		pins = "gpio125";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	ts_reset_suspend_state: ts-reset-suspend-state {
+		pins = "gpio89";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wcd_int_n: wcd-int-n {
+		pins = "gpio54";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+		input-enable;
+	};
+
+	wsa_leftspk_pwr_n: wsa-leftspk-pwr-n {
+		pins = "gpio65";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+		output-low;
+	};
+
+	wsa_rightspk_pwr_n: wsa-rightspk-pwr-n {
+		pins = "gpio66";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+		output-low;
+	};
+};
+
+&pm8998_resin {
+	debounce = <15625>;
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&ufshc {
+	status = "okay";
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vccq-supply = <&vreg_l26a_1p2>;
+	vccq2-supply = <&vreg_s4a_1p8>;
+	vcc-max-microamp = <750000>;
+	vccq-max-microamp = <560000>;
+	vccq2-max-microamp = <750000>;
+};
+
+&ufsphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l2a_1p2>;
+	vddp-ref-clk-supply = <&vreg_l26a_1p2>;
+};
+
+&usb3 {
+	status = "okay";
+
+	/* Disable USB3 clock requirement as the device only supports USB2 */
+	qcom,select-utmi-as-pipe-clk;
+};
+
+&usb3_dwc3 {
+	/* Drop the unused USB 3 PHY */
+	phys = <&qusb2phy>;
+	phy-names = "usb2-phy";
+
+	/* Fastest mode for USB 2 */
+	maximum-speed = "high-speed";
+
+	/* Force to peripheral until we can switch modes */
+	dr_mode = "peripheral";
+};
+
+&wifi {
+	status = "okay";
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+};
diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi
index d09f2954b6f9..4551af463081 100644
--- a/arch/arm64/boot/dts/qcom/pm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi
@@ -52,6 +52,12 @@ pm8998_pwrkey: pwrkey {
 				bias-pull-up;
 				linux,code = <KEY_POWER>;
 			};
+
+			pm8998_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				bias-pull-up;
+				interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+			};
 		};
 
 		pm8998_temp: temp-alarm@2400 {
-- 
2.30.2

[PATCH v3 2/2] dt-bindings: arm: add xiaomi,sagit board based on msm8998 chip

[Dzmitry Sankouski]

add xiaomi,sagit board (Xiaomi Mi 6) binding

Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
---
Changes for v3:
- remove unused 'sagit' compatible line

 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index fb1d00bcc847..294075bafb97 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -239,6 +239,7 @@ properties:
               - sony,xperia-lilac
               - sony,xperia-maple
               - sony,xperia-poplar
+              - xiaomi,sagit
           - const: qcom,msm8998
 
       - items:
-- 
2.30.2

Re: [PATCH v3 1/2] arm64: dts: qcom: sagit: add initial device tree for sagit

[Konrad Dybcio]

On 03/10/2022 20:54, Dzmitry Sankouski wrote:
> New device support - Xiaomi Mi6 phone
>
> What works:
> - storage
> - usb
> - power regulators
>
> Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
> ---
> Changes for v3:
> - regulators nodes renamed to match pattern 'regulators-[01]'
> - duplicate cci1-default node deleted
> - add state suffix to pinctrl
>
>   arch/arm64/boot/dts/qcom/Makefile             |   1 +
>   .../boot/dts/qcom/msm8998-xiaomi-sagit.dts    | 689 ++++++++++++++++++
>   arch/arm64/boot/dts/qcom/pm8998.dtsi          |   6 +
>   3 files changed, 696 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 1d86a33de528..0460aabf1b59 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -46,6 +46,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-oneplus-dumpling.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-lilac.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-maple.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-poplar.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-xiaomi-sagit.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= qrb5165-rb5.dtb
> diff --git a/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
> new file mode 100644
> index 000000000000..871492d44df5
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
> @@ -0,0 +1,689 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Xiaomi Mi 6 (sagit) device tree source based on msm8998-mtp.dtsi
> + *
> + * Copyright (c) 2022, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2022, Degdag Mohamed <degdagmohamed@gmail.com>
> + * Copyright (c) 2022, Dzmitry Sankouski <dsankouski@gmail.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "msm8998.dtsi"
> +#include "pm8005.dtsi"
> +#include "pm8998.dtsi"
> +#include "pmi8998.dtsi"
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> +
> +/*
> + * Delete following upstream (msm8998.dtsi) reserved
> + * memory mappings which are different in this device.
> + */
> +/delete-node/ &mpss_mem;
> +/delete-node/ &venus_mem;
> +/delete-node/ &mba_mem;
> +/delete-node/ &slpi_mem;
> +/delete-node/ &ipa_fw_mem;
> +/delete-node/ &ipa_gsi_mem;
> +/delete-node/ &gpu_mem;
> +/delete-node/ &wlan_msa_mem;
> +
> +/ {
> +	model = "Xiaomi Mi 6";
> +	compatible = "xiaomi,sagit", "qcom,msm8998";
> +	chassis-type = "handset";
> +	/* Required for bootloader to select correct board */
> +	qcom,board-id = <30 0>;
> +
> +	reserved-memory {
> +		/*
> +		 * The following memory regions on downstream are "dynamically allocated"
> +		 * but given the same addresses every time. Hard code them as these addresses
> +		 * are where the Xiaomi signed firmware expects them to be.
> +		 */
> +		ipa_fws_region: ipa@f7800000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x0 0xf7800000 0x0 0x5000>;
> +			no-map;
> +		};
> +
> +		zap_shader_region: gpu@f7900000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x0 0xf7900000 0x0 0x2000>;
> +			no-map;
> +		};
> +
> +		mpss_mem: memory@8d000000 {
> +			reg = <0x0 0x8d000000 0x0 0x7000000>;
> +			no-map;
> +		};
> +
> +		venus_mem: memory@94000000 {
> +			reg = <0x0 0x94000000 0x0 0x500000>;
> +			no-map;
> +		};
> +
> +		mba_mem: memory@94500000 {
> +			reg = <0x0 0x94500000 0x0 0x200000>;
> +			no-map;
> +		};
> +
> +		slpi_mem: memory@94700000 {
> +			reg = <0x0 0x94700000 0x0 0x10000>;
> +			no-map;
> +		};
> +
> +		ipa_fw_mem: memory@95600000 {
> +			reg = <0x0 0x95600000 0x0 0x10000>;
> +			no-map;
> +		};
> +
> +		ipa_gsi_mem: memory@95610000 {
> +			reg = <0x0 0x95610000 0x0 0x5000>;
> +			no-map;
> +		};
> +
> +		gpu_mem: memory@95615000 {
> +			reg = <0x0 0x95615000 0x0 0x100000>;
> +			no-map;
> +		};
> +
> +		wlan_msa_mem: memory@95715000 {
> +			reg = <0x0 0x95715000 0x0 0x100000>;
> +			no-map;
> +		};
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		label = "Volume buttons";
> +		autorepeat;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vol_up_key_default>;
> +
> +		key-vol-up {
> +			label = "Volume up";
> +			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_VOLUMEUP>;
> +			debounce-interval = <15>;
> +			wakeup-source;
> +		};
> +	};
> +
> +	gpio-hall-sensor {
> +		compatible = "gpio-keys";
> +		label = "Hall effect sensor";
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&hall_sensor_default>;
> +
> +		event-hall-sensor {
> +			label = "Hall Effect Sensor";
> +			gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
> +			linux,input-type = <EV_SW>;
> +			linux,code = <SW_LID>;
> +			linux,can-disable;
> +			wakeup-source;
> +		};
> +	};
> +
> +	vph_pwr: vph-pwr-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vph_pwr";
> +		regulator-min-microvolt = <3700000>;
> +		regulator-max-microvolt = <3700000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +
> +	disp_vddts_vreg: disp-vddts-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "disp-vddts-regulator";
> +		gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-boot-on;
> +	};
> +};
> +
> +&blsp1_i2c5 {
> +	pinctrl-names = "default", "sleep";
> +	status = "okay";
> +
> +	touchscreen@20 {
> +		compatible = "syna,rmi4-i2c";
> +		reg = <0x20>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		interrupt-parent = <&tlmm>;
> +		interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
> +
> +		pinctrl-names = "default", "sleep";
> +		pinctrl-0 = <&ts_active>;
> +		pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
> +
> +		vdd-supply = <&disp_vddts_vreg>;
> +		vio-supply = <&vreg_l6a_1p8>;
> +
> +		syna,reset-delay-ms = <20>;
> +		syna,startup-delay-ms = <20>;
> +
> +		rmi4-f01@1 {
> +			reg = <0x01>;
> +			syna,nosleep-mode = <1>;
> +		};
> +
> +		rmi4-f12@12 {
> +			reg = <0x12>;
> +			touchscreen-x-mm = <64>;
> +			touchscreen-y-mm = <114>;
> +			syna,sensor-type = <1>;
> +			syna,rezero-wait-ms = <20>;
> +		};
> +
> +		rmi4-f1a@1a {
> +			reg = <0x1a>;
> +			syna,codes = <KEY_BACK KEY_APPSELECT>;
> +		};
> +	};
> +};
> +
> +&blsp1_i2c5_sleep {
> +	/delete-property/ bias-pull-up;
> +	bias-disable;
> +};
> +
> +&blsp1_uart3 {
> +	status = "okay";
> +
> +	bluetooth {
> +		compatible = "qcom,wcn3990-bt";
> +
> +		vddio-supply = <&vreg_s4a_1p8>;
> +		vddxo-supply = <&vreg_l7a_1p8>;
> +		vddrf-supply = <&vreg_l17a_1p3>;
> +		vddch0-supply = <&vreg_l25a_3p3>;
> +		max-speed = <3200000>;
> +	};
> +};
> +
> +&blsp1_uart3_on {
> +	rx {
> +		/delete-property/ bias-disable;
> +		/*
> +		 * Configure a pull-up on 46 (RX). This is needed to
> +		 * avoid garbage data when the TX pin of the Bluetooth
> +		 * module is in tri-state (module powered off or not
> +		 * driving the signal yet).
> +		 */
> +		bias-pull-up;
> +	};
> +
> +	cts {
> +		/delete-property/ bias-disable;
> +		/*
> +		 * Configure a pull-down on 47 (CTS) to match the pull
> +		 * of the Bluetooth module.
> +		 */
> +		bias-pull-down;
> +	};
> +};
> +
> +&blsp2_uart1 {
> +	status = "okay";
> +};
> +
> +&pm8005_lsid1 {
> +	regulators-0 {
> +		compatible = "qcom,pm8005-regulators";
> +
> +		vdd_s1-supply = <&vph_pwr>;
> +
> +		pm8005_s1: s1 { /* VDD_GFX supply */
> +			regulator-min-microvolt = <524000>;
> +			regulator-max-microvolt = <1100000>;
> +			regulator-enable-ramp-delay = <500>;
> +
> +			/* hack until we rig up the gpu consumer */
> +			regulator-always-on;
> +		};
> +	};
> +};
> +
> +&pm8998_gpio {
> +	vol_up_key_default: vol-up-key-default-state {
> +		pins = "gpio6";
> +		function = "normal";
> +		bias-pull-up;
> +		input-enable;
> +		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
> +	};
> +
> +	audio_mclk_pin: audio-mclk-pin-active-state {
> +		pins = "gpio13";
> +		function = "func2";
> +		power-source = <0>;
> +	};
> +};
> +
> +&qusb2phy {
> +	status = "okay";
Status last. This applies to all cases.
> +
> +	vdda-pll-supply = <&vreg_l12a_1p8>;
> +	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
> +};
> +
> +&rpm_requests {
> +	regulators-0 {
> +		compatible = "qcom,rpm-pm8998-regulators";
> +
> +		vdd_s1-supply = <&vph_pwr>;
> +		vdd_s2-supply = <&vph_pwr>;
> +		vdd_s3-supply = <&vph_pwr>;
> +		vdd_s4-supply = <&vph_pwr>;
> +		vdd_s5-supply = <&vph_pwr>;
> +		vdd_s6-supply = <&vph_pwr>;
> +		vdd_s7-supply = <&vph_pwr>;
> +		vdd_s8-supply = <&vph_pwr>;
> +		vdd_s9-supply = <&vph_pwr>;
> +		vdd_s10-supply = <&vph_pwr>;
> +		vdd_s11-supply = <&vph_pwr>;
> +		vdd_s12-supply = <&vph_pwr>;
> +		vdd_s13-supply = <&vph_pwr>;
> +		vdd_l1_l27-supply = <&vreg_s7a_1p025>;
> +		vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
> +		vdd_l3_l11-supply = <&vreg_s7a_1p025>;
> +		vdd_l4_l5-supply = <&vreg_s7a_1p025>;
> +		vdd_l6-supply = <&vreg_s5a_2p04>;
> +		vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
> +		vdd_l9-supply = <&vreg_bob>;
> +		vdd_l10_l23_l25-supply = <&vreg_bob>;
> +		vdd_l13_l19_l21-supply = <&vreg_bob>;
> +		vdd_l16_l28-supply = <&vreg_bob>;
> +		vdd_l18_l22-supply = <&vreg_bob>;
> +		vdd_l20_l24-supply = <&vreg_bob>;
> +		vdd_l26-supply = <&vreg_s3a_1p35>;
> +		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
> +
> +		vreg_s3a_1p35: s3 {
> +			regulator-min-microvolt = <1352000>;
> +			regulator-max-microvolt = <1352000>;
> +		};
> +
> +		vreg_s4a_1p8: s4 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-allow-set-load;
> +		};
> +
> +		vreg_s5a_2p04: s5 {
> +			regulator-min-microvolt = <1904000>;
> +			regulator-max-microvolt = <2040000>;
> +		};
> +
> +		vreg_s7a_1p025: s7 {
> +			regulator-min-microvolt = <900000>;
> +			regulator-max-microvolt = <1028000>;
> +		};
> +
> +		vreg_l1a_0p875: l1 {
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <880000>;
> +		};
> +
> +		vreg_l2a_1p2: l2 {
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +		};
> +
> +		vreg_l3a_1p0: l3 {
> +			regulator-min-microvolt = <1000000>;
> +			regulator-max-microvolt = <1000000>;
> +		};
> +
> +		vreg_l5a_0p8: l5 {
> +			regulator-min-microvolt = <800000>;
> +			regulator-max-microvolt = <800000>;
> +		};
> +
> +		vreg_l6a_1p8: l6 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +		};
> +
> +		vreg_l7a_1p8: l7 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +		};
> +
> +		vreg_l8a_1p2: l8 {
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +		};
> +
> +		vreg_l9a_1p8: l9 {
> +			regulator-min-microvolt = <1808000>;
> +			regulator-max-microvolt = <2960000>;
> +		};
> +
> +		vreg_l10a_1p8: l10 {
> +			regulator-min-microvolt = <1808000>;
> +			regulator-max-microvolt = <2960000>;
> +		};
> +
> +		vreg_l11a_1p0: l11 {
> +			regulator-min-microvolt = <1000000>;
> +			regulator-max-microvolt = <1000000>;
> +		};
> +
> +		vreg_l12a_1p8: l12 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +		};
> +
> +		vreg_l13a_2p95: l13 {
> +			regulator-min-microvolt = <1808000>;
> +			regulator-max-microvolt = <2960000>;
> +		};
> +
> +		vreg_l14a_1p8: l14 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +		};
> +
> +		vreg_l15a_1p8: l15 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +		};
> +
> +		vreg_l16a_2p7: l16 {
> +			regulator-min-microvolt = <2704000>;
> +			regulator-max-microvolt = <2704000>;
> +		};
> +
> +		vreg_l17a_1p3: l17 {
> +			regulator-min-microvolt = <1304000>;
> +			regulator-max-microvolt = <1304000>;
> +		};
> +
> +		vreg_l18a_2p7: l18 {
> +			regulator-min-microvolt = <2704000>;
> +			regulator-max-microvolt = <2704000>;
> +		};
> +
> +		vreg_l19a_3p0: l19 {
> +			regulator-min-microvolt = <3008000>;
> +			regulator-max-microvolt = <3008000>;
> +		};
> +
> +		vreg_l20a_2p95: l20 {
> +			regulator-min-microvolt = <2960000>;
> +			regulator-max-microvolt = <2960000>;
> +			regulator-allow-set-load;
> +		};
> +
> +		vreg_l21a_2p95: l21 {
> +			regulator-min-microvolt = <2960000>;
> +			regulator-max-microvolt = <2960000>;
> +			regulator-system-load = <800000>;
> +			regulator-allow-set-load;
> +		};
> +
> +		vreg_l22a_2p85: l22 {
> +			regulator-min-microvolt = <2864000>;
> +			regulator-max-microvolt = <2864000>;
> +		};
> +
> +		vreg_l23a_3p3: l23 {
> +			regulator-min-microvolt = <3312000>;
> +			regulator-max-microvolt = <3312000>;
> +		};
> +
> +		vreg_l24a_3p075: l24 {
> +			regulator-min-microvolt = <3088000>;
> +			regulator-max-microvolt = <3088000>;
> +		};
> +
> +		vreg_l25a_3p3: l25 {
> +			regulator-min-microvolt = <3104000>;
> +			regulator-max-microvolt = <3312000>;
> +		};
> +
> +		vreg_l26a_1p2: l26 {
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-allow-set-load;
> +		};
> +
> +		vreg_l28_3p0: l28 {
> +			regulator-min-microvolt = <3008000>;
> +			regulator-max-microvolt = <3008000>;
> +		};
> +
> +		vreg_lvs1a_1p8: lvs1 { };
> +
> +		vreg_lvs2a_1p8: lvs2 { };
> +	};
> +
> +	regulators-1 {
> +		compatible = "qcom,rpm-pmi8998-regulators";
> +
> +		vdd_bob-supply = <&vph_pwr>;
> +
> +		vreg_bob: bob {
> +			regulator-min-microvolt = <3312000>;
> +			regulator-max-microvolt = <3600000>;
> +		};
> +	};
> +};
> +
> +&tlmm {
> +	gpio-reserved-ranges = <0 4>, <81 4>;
> +
> +	cci1_default_state: cci1-default-state {
> +		pins = "gpio19", "gpio20";
> +		function = "cci_i2c";
> +		bias-disable;
> +		drive-strength = <2>;
> +	};
> +
> +	cdc_reset_n: cdc-reset-n {

This node name and a couple others seem not to end in -state.


> +		pins = "gpio64";
> +		function = "gpio";
> +		bias-pull-down;
> +		drive-strength = <16>;
> +		output-high;
> +	};
> +
> +	hall_sensor_default_state: hall-sensor-default-state {
> +		pins = "gpio124";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +		input-enable;
> +	};
> +
> +	mdss_dsi_active_state: mdss-dsi-active-state {
> +		pins = "gpio94";
> +		function = "gpio";
> +		drive-strength = <8>;
> +		bias-disable;
> +	};
> +
> +	mdss_dsi_suspend_state: mdss-dsi-suspend-state {
> +		pins = "gpio94";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	mdss_te_active_state: mdss-te-active-state {
> +		pins = "gpio10";
> +		function = "mdp_vsync_a";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	mdss_te_suspend_state: mdss-te-suspend-state {
> +		pins = "gpio10";
> +		function = "mdp_vsync_a";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	msm_mclk0_active_state: msm-mclk0-active-state {
> +		pins = "gpio13";
> +		function = "cam_mclk";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	msm_mclk0_suspend_state: msm-mclk0-suspend-state {
> +		pins = "gpio13";
> +		function = "cam_mclk";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	msm_mclk1_active_state: msm-mclk1-active-state {
> +		pins = "gpio14";
> +		function = "cam_mclk";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	msm_mclk1_suspend_state: msm-mclk1-suspend-state {
> +		pins = "gpio14";
> +		function = "cam_mclk";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	nfc_int_active_state: nfc-int-active-state {
> +		pins = "gpio92";
> +		function = "gpio";
> +		drive-strength = <6>;
> +		bias-pull-up;
> +	};
> +
> +	nfc_int_suspend_state: nfc-int-suspend-state {
> +		pins = "gpio92";
> +		function = "gpio";
> +		drive-strength = <6>;
> +		bias-pull-up;
> +	};
> +
> +	nfc_enable_active_state: nfc-enable-active-state {
> +		pins = "gpio12", "gpio116";
> +		function = "gpio";
> +		drive-strength = <6>;
> +		bias-pull-up;
> +	};
> +
> +	nfc_enable_suspend_state: nfc-enable-suspend-state {
> +		pins = "gpio12", "gpio116";
> +		function = "gpio";
> +		drive-strength = <6>;
> +		bias-disable;
> +	};
> +
> +	ts_active_state: ts-active-state {
> +		pins = "gpio89", "gpio125";
> +		function = "gpio";
> +		drive-strength = <16>;
> +		bias-pull-up;
> +		input-enable;
> +	};
> +
> +	ts_int_suspend_state: ts-int-suspend-state {
> +		pins = "gpio125";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	ts_reset_suspend_state: ts-reset-suspend-state {
> +		pins = "gpio89";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	wcd_int_n: wcd-int-n {
> +		pins = "gpio54";
> +		function = "gpio";
> +		bias-pull-down;
> +		drive-strength = <2>;
> +		input-enable;
> +	};
> +
> +	wsa_leftspk_pwr_n: wsa-leftspk-pwr-n {
> +		pins = "gpio65";
> +		function = "gpio";
> +		bias-disable;
> +		drive-strength = <2>;
> +		output-low;
> +	};
> +
> +	wsa_rightspk_pwr_n: wsa-rightspk-pwr-n {
> +		pins = "gpio66";
> +		function = "gpio";
> +		bias-disable;
> +		drive-strength = <2>;
> +		output-low;
> +	};
> +};
> +
> +&pm8998_resin {
> +	debounce = <15625>;
> +	linux,code = <KEY_VOLUMEDOWN>;
> +};
> +
> +&ufshc {
> +	status = "okay";
> +
> +	vcc-supply = <&vreg_l20a_2p95>;
> +	vccq-supply = <&vreg_l26a_1p2>;
> +	vccq2-supply = <&vreg_s4a_1p8>;
> +	vcc-max-microamp = <750000>;
> +	vccq-max-microamp = <560000>;
> +	vccq2-max-microamp = <750000>;
> +};
> +
> +&ufsphy {
> +	status = "okay";
> +
> +	vdda-phy-supply = <&vreg_l1a_0p875>;
> +	vdda-pll-supply = <&vreg_l2a_1p2>;
> +	vddp-ref-clk-supply = <&vreg_l26a_1p2>;
> +};
> +
> +&usb3 {
> +	status = "okay";
> +
> +	/* Disable USB3 clock requirement as the device only supports USB2 */
> +	qcom,select-utmi-as-pipe-clk;
> +};
> +
> +&usb3_dwc3 {
> +	/* Drop the unused USB 3 PHY */
> +	phys = <&qusb2phy>;
> +	phy-names = "usb2-phy";
> +
> +	/* Fastest mode for USB 2 */
> +	maximum-speed = "high-speed";
> +
> +	/* Force to peripheral until we can switch modes */
> +	dr_mode = "peripheral";
> +};
> +
> +&wifi {
> +	status = "okay";
> +	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
> +	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
> +	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
> +	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
> +};
> diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi
> index d09f2954b6f9..4551af463081 100644
> --- a/arch/arm64/boot/dts/qcom/pm8998.dtsi
> +++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi
> @@ -52,6 +52,12 @@ pm8998_pwrkey: pwrkey {
>   				bias-pull-up;
>   				linux,code = <KEY_POWER>;
>   			};
> +
> +			pm8998_resin: resin {
> +				compatible = "qcom,pm8941-resin";
> +				bias-pull-up;
> +				interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
> +			};

Should be disabled by default; you can move the debounce param here.


Konrad

>   		};
>   
>   		pm8998_temp: temp-alarm@2400 {

Re: [PATCH v3 2/2] dt-bindings: arm: add xiaomi,sagit board based on msm8998 chip

[Konrad Dybcio]

On 03/10/2022 20:55, Dzmitry Sankouski wrote:
> add xiaomi,sagit board (Xiaomi Mi 6) binding
>
> Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
> ---

Binding changes should generally go before the actual patch, so that

there's no commit where there's an undocumented compatible.

Konrad

> Changes for v3:
> - remove unused 'sagit' compatible line
>
>   Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
>   1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
> index fb1d00bcc847..294075bafb97 100644
> --- a/Documentation/devicetree/bindings/arm/qcom.yaml
> +++ b/Documentation/devicetree/bindings/arm/qcom.yaml
> @@ -239,6 +239,7 @@ properties:
>                 - sony,xperia-lilac
>                 - sony,xperia-maple
>                 - sony,xperia-poplar
> +              - xiaomi,sagit
>             - const: qcom,msm8998
>   
>         - items:

Re: [PATCH v3 2/2] dt-bindings: arm: add xiaomi,sagit board based on msm8998 chip

[Krzysztof Kozlowski]

On 03/10/2022 20:55, Dzmitry Sankouski wrote:
> add xiaomi,sagit board (Xiaomi Mi 6) binding

Start with capital letter and finish with full-stop.

> 
> Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
> ---
> Changes for v3:
> - remove unused 'sagit' compatible line

With commit fixes:

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH v3 1/2] arm64: dts: qcom: sagit: add initial device tree for sagit

[Krzysztof Kozlowski]

On 03/10/2022 20:54, Dzmitry Sankouski wrote:
> New device support - Xiaomi Mi6 phone
> 
> What works:
> - storage
> - usb
> - power regulators
> 
> Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>

Thank you for your patch. There is something to discuss/improve.

> +
> +&tlmm {
> +	gpio-reserved-ranges = <0 4>, <81 4>;
> +
> +	cci1_default_state: cci1-default-state {
> +		pins = "gpio19", "gpio20";
> +		function = "cci_i2c";
> +		bias-disable;
> +		drive-strength = <2>;
> +	};
> +
> +	cdc_reset_n: cdc-reset-n {

This is a friendly reminder during the review process.

It seems my previous comments were not fully addressed. Maybe my
feedback got lost between the quotes, maybe you just forgot to apply it.
Please go back to the previous discussion and either implement all
requested changes or keep discussing them.

Thank you.

> +		pins = "gpio64";
> +		function = "gpio";
> +		bias-pull-down;
> +		drive-strength = <16>;
> +		output-high;
> +	};
> +
> +	hall_sensor_default_state: hall-sensor-default-state {
> +		pins = "gpio124";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +		input-enable;
> +	};
> +
> +	mdss_dsi_active_state: mdss-dsi-active-state {
> +		pins = "gpio94";
> +		function = "gpio";
> +		drive-strength = <8>;
> +		bias-disable;
> +	};
> +
> +	mdss_dsi_suspend_state: mdss-dsi-suspend-state {
> +		pins = "gpio94";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	mdss_te_active_state: mdss-te-active-state {
> +		pins = "gpio10";
> +		function = "mdp_vsync_a";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	mdss_te_suspend_state: mdss-te-suspend-state {
> +		pins = "gpio10";
> +		function = "mdp_vsync_a";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	msm_mclk0_active_state: msm-mclk0-active-state {
> +		pins = "gpio13";
> +		function = "cam_mclk";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	msm_mclk0_suspend_state: msm-mclk0-suspend-state {
> +		pins = "gpio13";
> +		function = "cam_mclk";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	msm_mclk1_active_state: msm-mclk1-active-state {
> +		pins = "gpio14";
> +		function = "cam_mclk";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	msm_mclk1_suspend_state: msm-mclk1-suspend-state {
> +		pins = "gpio14";
> +		function = "cam_mclk";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	nfc_int_active_state: nfc-int-active-state {
> +		pins = "gpio92";
> +		function = "gpio";
> +		drive-strength = <6>;
> +		bias-pull-up;
> +	};
> +
> +	nfc_int_suspend_state: nfc-int-suspend-state {
> +		pins = "gpio92";
> +		function = "gpio";
> +		drive-strength = <6>;
> +		bias-pull-up;
> +	};
> +
> +	nfc_enable_active_state: nfc-enable-active-state {
> +		pins = "gpio12", "gpio116";
> +		function = "gpio";
> +		drive-strength = <6>;
> +		bias-pull-up;
> +	};
> +
> +	nfc_enable_suspend_state: nfc-enable-suspend-state {
> +		pins = "gpio12", "gpio116";
> +		function = "gpio";
> +		drive-strength = <6>;
> +		bias-disable;
> +	};
> +
> +	ts_active_state: ts-active-state {
> +		pins = "gpio89", "gpio125";
> +		function = "gpio";
> +		drive-strength = <16>;
> +		bias-pull-up;
> +		input-enable;
> +	};
> +
> +	ts_int_suspend_state: ts-int-suspend-state {
> +		pins = "gpio125";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	ts_reset_suspend_state: ts-reset-suspend-state {
> +		pins = "gpio89";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	wcd_int_n: wcd-int-n {

You missed here state suffix

> +		pins = "gpio54";
> +		function = "gpio";
> +		bias-pull-down;
> +		drive-strength = <2>;
> +		input-enable;
> +	};
> +
> +	wsa_leftspk_pwr_n: wsa-leftspk-pwr-n {

Ditto

> +		pins = "gpio65";
> +		function = "gpio";
> +		bias-disable;
> +		drive-strength = <2>;
> +		output-low;
> +	};
> +> +	wsa_rightspk_pwr_n: wsa-rightspk-pwr-n {

Ditto

> +		pins = "gpio66";
> +		function = "gpio";
> +		bias-disable;
> +		drive-strength = <2>;
> +		output-low;
> +	};

Best regards,
Krzysztof