Re: [PATCH v3 7/7] arm64: dts: qcom: sa8155: Enable PCIe nodes

[Bhupesh Sharma <bhupesh.sharma@linaro.org>]

Hi Dmitry,

On Thu, 3 Mar 2022 at 02:29, Dmitry Baryshkov
<dmitry.baryshkov@linaro.org> wrote:
>
> On Wed, 2 Mar 2022 at 23:31, Bhupesh Sharma <bhupesh.sharma@linaro.org> wrote:
> >
> > SA8155p ADP board supports the PCIe0 controller in the RC
> > mode (only). So add the support for the same.
> >
> > Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
> > Cc: Vinod Koul <vkoul@kernel.org>
> > Cc: Rob Herring <robh+dt@kernel.org>
> > Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
> > ---
> >  arch/arm64/boot/dts/qcom/sa8155p-adp.dts | 42 ++++++++++++++++++++++++
> >  1 file changed, 42 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sa8155p-adp.dts b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
> > index 8756c2b25c7e..3f6b3ee404f5 100644
> > --- a/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
> > +++ b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
> > @@ -387,9 +387,51 @@ &usb_2_qmpphy {
> >         vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
> >  };
> >
> > +&pcie0 {
> > +       status = "okay";
> > +};
> > +
> > +&pcie0_phy {
> > +       status = "okay";
> > +       vdda-phy-supply = <&vreg_l18c_0p88>;
> > +       vdda-pll-supply = <&vreg_l8c_1p2>;
> > +};
> > +
> > +&pcie1_phy {
> > +       vdda-phy-supply = <&vreg_l18c_0p88>;
> > +       vdda-pll-supply = <&vreg_l8c_1p2>;
> > +};
> > +
> >  &tlmm {
> >         gpio-reserved-ranges = <0 4>;
> >
> > +       bt_en_default: bt_en_default {
> > +               mux {
> > +                       pins = "gpio172";
> > +                       function = "gpio";
> > +               };
> > +
> > +               config {
> > +                       pins = "gpio172";
> > +                       drive-strength = <2>;
> > +                       bias-pull-down;
> > +               };
> > +       };
> > +
> > +       wlan_en_default: wlan_en_default {
> > +               mux {
> > +                       pins = "gpio169";
> > +                       function = "gpio";
> > +               };
> > +
> > +               config {
> > +                       pins = "gpio169";
> > +                       drive-strength = <16>;
> > +                       output-high;
> > +                       bias-pull-up;
> > +               };
> > +       };
> > +
>
> Not related to PCIe

Hmm.. I have no strong personal opinion on this, so let's see what
Bjorn thinks about the same.
My reasoning for keeping it here was to just capture that we have
'bt_en' and 'wlan_en' related tlmm details here, so that when you send
out the reworked QCAxxxx mfd series (see [1]) later, I can easily plug
it in for SA8155p ADP dts as well with the 'bt' and 'wlan' constructs.

[1]. https://lore.kernel.org/lkml/20210621223141.1638189-2-dmitry.baryshkov@linaro.org/T/

Regards.
Bhupesh

> >         usb2phy_ac_en1_default: usb2phy_ac_en1_default {
> >                 mux {
> >                         pins = "gpio113";
> > --
> > 2.35.1
> >
>
>
> --
> With best wishes
> Dmitry