From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Vinod Koul <vkoul@kernel.org>
Cc: Stephen Boyd <sboyd@kernel.org>,
linux-arm-msm@vger.kernel.org,
Vivek Aknurwar <viveka@codeaurora.org>,
Andy Gross <agross@kernel.org>,
Michael Turquette <mturquette@baylibre.com>,
Rob Herring <robh+dt@kernel.org>,
Taniya Das <tdas@codeaurora.org>,
AngeloGioacchino Del Regno
<angelogioacchino.delregno@somainline.org>,
linux-clk@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Jeevan Shriram <jshriram@codeaurora.org>
Subject: Re: [PATCH v4 3/5] clk: qcom: clk-alpha-pll: Add support for Lucid 5LPE PLL
Date: Mon, 25 Jan 2021 11:18:08 -0600 [thread overview]
Message-ID: <YA79UPODso3cmMFU@builder.lan> (raw)
In-Reply-To: <20210118044321.2571775-4-vkoul@kernel.org>
On Sun 17 Jan 22:43 CST 2021, Vinod Koul wrote:
> From: Vivek Aknurwar <viveka@codeaurora.org>
>
> Lucid 5LPE is a slightly different Lucid PLL with different offsets and
> porgramming sequence so add support for these
>
> Signed-off-by: Vivek Aknurwar <viveka@codeaurora.org>
> Signed-off-by: Jeevan Shriram <jshriram@codeaurora.org>
> [vkoul: rebase and tidy up for upstream]
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
> drivers/clk/qcom/clk-alpha-pll.c | 173 +++++++++++++++++++++++++++++++
> drivers/clk/qcom/clk-alpha-pll.h | 4 +
> 2 files changed, 177 insertions(+)
>
> diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
> index a30ea7b09224..f9c48da21bd1 100644
> --- a/drivers/clk/qcom/clk-alpha-pll.c
> +++ b/drivers/clk/qcom/clk-alpha-pll.c
> @@ -156,6 +156,12 @@ EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);
> /* LUCID PLL specific settings and offsets */
> #define LUCID_PCAL_DONE BIT(27)
>
> +/* LUCID 5LPE PLL specific settings and offsets */
> +#define LUCID_5LPE_PCAL_DONE BIT(11)
> +#define LUCID_5LPE_ALPHA_PLL_ACK_LATCH BIT(13)
> +#define LUCID_5LPE_PLL_LATCH_INPUT BIT(14)
> +#define LUCID_5LPE_ENABLE_VOTE_RUN BIT(21)
> +
> #define pll_alpha_width(p) \
> ((PLL_ALPHA_VAL_U(p) - PLL_ALPHA_VAL(p) == 4) ? \
> ALPHA_REG_BITWIDTH : ALPHA_REG_16BIT_WIDTH)
> @@ -1604,3 +1610,170 @@ const struct clk_ops clk_alpha_pll_agera_ops = {
> .set_rate = clk_alpha_pll_agera_set_rate,
> };
> EXPORT_SYMBOL_GPL(clk_alpha_pll_agera_ops);
> +
> +static int alpha_pll_lucid_5lpe_enable(struct clk_hw *hw)
> +{
> + struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
> + u32 val;
> + int ret;
> +
> + ret = regmap_read(pll->clkr.regmap, PLL_USER_CTL(pll), &val);
> + if (ret)
> + return ret;
> +
> + /* If in FSM mode, just vote for it */
> + if (val & LUCID_5LPE_ENABLE_VOTE_RUN) {
> + ret = clk_enable_regmap(hw);
> + if (ret)
> + return ret;
> + return wait_for_pll_enable_lock(pll);
> + }
> +
> + /* Check if PLL is already enabled, return if enabled */
> + ret = trion_pll_is_enabled(pll, pll->clkr.regmap);
> + if (ret < 0)
> + return ret;
> +
> + ret = regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll), PLL_RESET_N, PLL_RESET_N);
> + if (ret)
> + return ret;
> +
> + regmap_write(pll->clkr.regmap, PLL_OPMODE(pll), PLL_RUN);
> +
> + ret = wait_for_pll_enable_lock(pll);
> + if (ret)
> + return ret;
> +
> + /* Enable the PLL outputs */
> + ret = regmap_update_bits(pll->clkr.regmap, PLL_USER_CTL(pll), PLL_OUT_MASK, PLL_OUT_MASK);
> + if (ret)
> + return ret;
> +
> + /* Enable the global PLL outputs */
> + return regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll), PLL_OUTCTRL, PLL_OUTCTRL);
> +}
> +
> +static void alpha_pll_lucid_5lpe_disable(struct clk_hw *hw)
> +{
> + struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
> + u32 val;
> + int ret;
> +
> + ret = regmap_read(pll->clkr.regmap, PLL_USER_CTL(pll), &val);
> + if (ret)
> + return;
> +
> + /* If in FSM mode, just unvote it */
> + if (val & LUCID_5LPE_ENABLE_VOTE_RUN) {
> + clk_disable_regmap(hw);
> + return;
> + }
> +
> + /* Disable the global PLL output */
> + ret = regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll), PLL_OUTCTRL, 0);
> + if (ret)
> + return;
> +
> + /* Disable the PLL outputs */
> + ret = regmap_update_bits(pll->clkr.regmap, PLL_USER_CTL(pll), PLL_OUT_MASK, 0);
> + if (ret)
> + return;
> +
> + /* Place the PLL mode in STANDBY */
> + regmap_write(pll->clkr.regmap, PLL_OPMODE(pll), PLL_STANDBY);
> +}
> +
> +/*
> + * The Lucid 5LPE PLL requires a power-on self-calibration which happens
> + * when the PLL comes out of reset. Calibrate in case it is not completed.
> + */
> +static int alpha_pll_lucid_5lpe_prepare(struct clk_hw *hw)
> +{
> + struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
> + struct clk_hw *p;
> + u32 val;
> + int ret;
> +
> + /* Return early if calibration is not needed. */
> + regmap_read(pll->clkr.regmap, PLL_MODE(pll), &val);
I doubt this will ever fail, but static analysis tools would complain
about val possibly being uninitialized after this.
And the return value is checked in the other functions.
Regards,
Bjorn
> + if (val & LUCID_5LPE_PCAL_DONE)
> + return 0;
> +
> + p = clk_hw_get_parent(hw);
> + if (!p)
> + return -EINVAL;
> +
> + ret = alpha_pll_lucid_5lpe_enable(hw);
> + if (ret)
> + return ret;
> +
> + alpha_pll_lucid_5lpe_disable(hw);
> +
> + return 0;
> +}
> +
> +static int alpha_pll_lucid_5lpe_set_rate(struct clk_hw *hw, unsigned long rate,
> + unsigned long prate)
> +{
> + return __alpha_pll_trion_set_rate(hw, rate, prate,
> + LUCID_5LPE_PLL_LATCH_INPUT,
> + LUCID_5LPE_ALPHA_PLL_ACK_LATCH);
> +}
> +
> +static int clk_lucid_5lpe_pll_postdiv_set_rate(struct clk_hw *hw, unsigned long rate,
> + unsigned long parent_rate)
> +{
> + struct clk_alpha_pll_postdiv *pll = to_clk_alpha_pll_postdiv(hw);
> + int i, val = 0, div, ret;
> + u32 mask;
> +
> + /*
> + * If the PLL is in FSM mode, then treat set_rate callback as a
> + * no-operation.
> + */
> + ret = regmap_read(pll->clkr.regmap, PLL_USER_CTL(pll), &val);
> + if (ret)
> + return ret;
> +
> + if (val & LUCID_5LPE_ENABLE_VOTE_RUN)
> + return 0;
> +
> + div = DIV_ROUND_UP_ULL((u64)parent_rate, rate);
> + for (i = 0; i < pll->num_post_div; i++) {
> + if (pll->post_div_table[i].div == div) {
> + val = pll->post_div_table[i].val;
> + break;
> + }
> + }
> +
> + mask = GENMASK(pll->width + pll->post_div_shift - 1, pll->post_div_shift);
> + return regmap_update_bits(pll->clkr.regmap, PLL_USER_CTL(pll),
> + mask, val << pll->post_div_shift);
> +}
> +
> +const struct clk_ops clk_alpha_pll_lucid_5lpe_ops = {
> + .prepare = alpha_pll_lucid_5lpe_prepare,
> + .enable = alpha_pll_lucid_5lpe_enable,
> + .disable = alpha_pll_lucid_5lpe_disable,
> + .is_enabled = clk_trion_pll_is_enabled,
> + .recalc_rate = clk_trion_pll_recalc_rate,
> + .round_rate = clk_alpha_pll_round_rate,
> + .set_rate = alpha_pll_lucid_5lpe_set_rate,
> +};
> +EXPORT_SYMBOL(clk_alpha_pll_lucid_5lpe_ops);
> +
> +const struct clk_ops clk_alpha_pll_fixed_lucid_5lpe_ops = {
> + .enable = alpha_pll_lucid_5lpe_enable,
> + .disable = alpha_pll_lucid_5lpe_disable,
> + .is_enabled = clk_trion_pll_is_enabled,
> + .recalc_rate = clk_trion_pll_recalc_rate,
> + .round_rate = clk_alpha_pll_round_rate,
> +};
> +EXPORT_SYMBOL(clk_alpha_pll_fixed_lucid_5lpe_ops);
> +
> +const struct clk_ops clk_alpha_pll_postdiv_lucid_5lpe_ops = {
> + .recalc_rate = clk_alpha_pll_postdiv_fabia_recalc_rate,
> + .round_rate = clk_alpha_pll_postdiv_fabia_round_rate,
> + .set_rate = clk_lucid_5lpe_pll_postdiv_set_rate,
> +};
> +EXPORT_SYMBOL(clk_alpha_pll_postdiv_lucid_5lpe_ops);
> diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
> index 0ea30d2f3da1..6943e933be0f 100644
> --- a/drivers/clk/qcom/clk-alpha-pll.h
> +++ b/drivers/clk/qcom/clk-alpha-pll.h
> @@ -144,6 +144,10 @@ extern const struct clk_ops clk_alpha_pll_lucid_ops;
> extern const struct clk_ops clk_alpha_pll_postdiv_lucid_ops;
> extern const struct clk_ops clk_alpha_pll_agera_ops;
>
> +extern const struct clk_ops clk_alpha_pll_lucid_5lpe_ops;
> +extern const struct clk_ops clk_alpha_pll_fixed_lucid_5lpe_ops;
> +extern const struct clk_ops clk_alpha_pll_postdiv_lucid_5lpe_ops;
> +
> void clk_alpha_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
> const struct alpha_pll_config *config);
> void clk_fabia_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
> --
> 2.26.2
>
next prev parent reply other threads:[~2021-01-25 17:23 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-01-18 4:43 [PATCH v4 0/5] Add clock drivers for SM8350 Vinod Koul
2021-01-18 4:43 ` [PATCH v4 1/5] clk: qcom: clk-alpha-pll: replace regval with val Vinod Koul
2021-01-25 17:13 ` Bjorn Andersson
2021-01-18 4:43 ` [PATCH v4 2/5] clk: qcom: clk-alpha-pll: modularize alpha_pll_trion_set_rate() Vinod Koul
2021-01-25 17:14 ` Bjorn Andersson
2021-01-18 4:43 ` [PATCH v4 3/5] clk: qcom: clk-alpha-pll: Add support for Lucid 5LPE PLL Vinod Koul
2021-01-19 21:54 ` AngeloGioacchino Del Regno
2021-01-25 17:18 ` Bjorn Andersson [this message]
2021-01-26 7:59 ` Vinod Koul
2021-01-18 4:43 ` [PATCH v4 4/5] dt-bindings: clock: Add SM8350 GCC clock bindings Vinod Koul
2021-01-25 17:25 ` Bjorn Andersson
2021-01-26 8:00 ` Vinod Koul
2021-01-26 14:17 ` Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=YA79UPODso3cmMFU@builder.lan \
--to=bjorn.andersson@linaro.org \
--cc=agross@kernel.org \
--cc=angelogioacchino.delregno@somainline.org \
--cc=devicetree@vger.kernel.org \
--cc=jshriram@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mturquette@baylibre.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=tdas@codeaurora.org \
--cc=viveka@codeaurora.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).