Re: [PATCH 2/3] arm64: dts: qcom: sc7280: Add PCIe and PHY related nodes

[Bjorn Andersson <bjorn.andersson@linaro.org>]

On Fri 04 Jun 16:43 CDT 2021, Stephen Boyd wrote:

> Quoting Prasad Malisetty (2021-05-21 02:57:00)
> > On 2021-05-08 01:36, Stephen Boyd wrote:
> > > Quoting Prasad Malisetty (2021-05-07 03:17:27)
> > >> Add PCIe controller and PHY nodes for sc7280 SOC.
> > >>
> > >> Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org>
> > >> ---
> > >>  arch/arm64/boot/dts/qcom/sc7280.dtsi | 138
> > >> +++++++++++++++++++++++++++++++++++
> > >>  1 file changed, 138 insertions(+)
> > >>
> > >> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> > >> b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> > >> index 2cc4785..a9f25fc1 100644
> > >> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> > >> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> > >> @@ -12,6 +12,7 @@
> > >>  #include <dt-bindings/power/qcom-aoss-qmp.h>
> > >>  #include <dt-bindings/power/qcom-rpmpd.h>
> > >>  #include <dt-bindings/soc/qcom,rpmh-rsc.h>
> > >> +#include <dt-bindings/gpio/gpio.h>
> > >>
> > >>  / {
> > >>         interrupt-parent = <&intc>;
> > >> @@ -316,6 +317,118 @@
> > >>                         };
> > >>                 };
> > >>
> > > [...]
> > >> +
> > >> +               pcie1_phy: phy@1c0e000 {
> > >> +                       compatible =
> > >> "qcom,sm8250-qmp-gen3x2-pcie-phy";
> > >> +                       reg = <0 0x01c0e000 0 0x1c0>;
> > >> +                       #address-cells = <2>;
> > >> +                       #size-cells = <2>;
> > >> +                       ranges;
> > >> +                       clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
> > >> +                                <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
> > >> +                                <&gcc GCC_PCIE_CLKREF_EN>,
> > >> +                                <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
> > >> +                       clock-names = "aux", "cfg_ahb", "ref",
> > >> "refgen";
> > >> +
> > >> +                       resets = <&gcc GCC_PCIE_1_PHY_BCR>;
> > >> +                       reset-names = "phy";
> > >> +
> > >> +                       assigned-clocks = <&gcc
> > >> GCC_PCIE1_PHY_RCHNG_CLK>;
> > >> +                       assigned-clock-rates = <100000000>;
> > >> +
> > >> +                       status = "disabled";
> > >
> > > I think the style is to put status disabled close to the compatible?
> >
> > Generally I have added status disabled in end as like many nodes. just
> > curious to ask is there any specific reason to put close to compatible.
> 
> It's really up to qcom maintainers, which I am not.
> 

I like when it's the last item, as it lends itself nicely to be
surrounded by empty lines and thereby easy to spot...

Regards,
Bjorn

> > >> +                               };
> > >> +
> > >> +                               reset-n {
> > >> +                                       pins = "gpio2";
> > >> +                                       function = "gpio";
> > >> +
> > >> +                                       drive-strength = <16>;
> > >> +                                       output-low;
> > >> +                                       bias-disable;
> > >> +                               };
> > >> +
> > >> +                               wake-n {
> > >> +                                       pins = "gpio3";
> > >> +                                       function = "gpio";
> > >> +
> > >> +                                       drive-strength = <2>;
> > >> +                                       bias-pull-up;
> > >> +                               };
> > >
> > > These last two nodes with the pull-up and drive-strength settings
> > > should
> > > be in the board files, like the idp one, instead of here in the SoC
> > > file. That way board designers can take the SoC and connect the pcie to
> > > an external device using these pins and set the configuration they want
> > > on these pins, or choose not to connect them to the SoC at all and use
> > > those pins for something else.
> > >
> > > In addition, it looks like the reset could be a reset-gpios property
> > > instead of an output-low config.
> > >
> > we are using reset property as perst gpio in pcie node.
> 
> Ok, perst-gpios should be fine. Presumably perst-gpios should be in the
> board and not in the SoC because of what I wrote up above.