Re: [PATCH 1/2] arm64: dts: qcom: Use consistent naming for dwc3 usb nodes for sm8150

[Bjorn Andersson <bjorn.andersson@linaro.org>]

On Fri 25 Jun 17:03 CDT 2021, Bhupesh Sharma wrote:

> The dwc3 usb nodes in sm8150.dtsi are currently named differently,
> leading to some confusion when one sees the entries in sysfs or
> dmesg:
> [    1.943482] dwc3 a600000.usb: Adding to iommu group 1
> [    2.266127] dwc3 a800000.dwc3: Adding to iommu group 2
> 
> Name both the nodes as dwc3@<addr> for consistency.
> 
> While at it also arrange the two usb controller, hs-phy and
> ss-phy nodes closer in the dts for better readability.
> 
> Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm8150.dtsi | 30 ++++++++++++++--------------
>  1 file changed, 15 insertions(+), 15 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> index 612dda0fef43..3be6d093a99b 100644
> --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> @@ -2205,6 +2205,20 @@ glink-edge {
>  			};
>  		};
>  
> +		dc_noc: interconnect@9160000 {
> +			compatible = "qcom,sm8150-dc-noc";
> +			reg = <0 0x09160000 0 0x3200>;
> +			#interconnect-cells = <1>;
> +			qcom,bcm-voters = <&apps_bcm_voter>;
> +		};
> +
> +		gem_noc: interconnect@9680000 {
> +			compatible = "qcom,sm8150-gem-noc";
> +			reg = <0 0x09680000 0 0x3e200>;
> +			#interconnect-cells = <1>;
> +			qcom,bcm-voters = <&apps_bcm_voter>;
> +		};
> +
>  		usb_1_hsphy: phy@88e2000 {
>  			compatible = "qcom,sm8150-usb-hs-phy",
>  				     "qcom,usb-snps-hs-7nm-phy";
> @@ -2266,20 +2280,6 @@ usb_1_ssphy: lanes@88e9200 {
>  			};
>  		};
>  
> -		dc_noc: interconnect@9160000 {
> -			compatible = "qcom,sm8150-dc-noc";
> -			reg = <0 0x09160000 0 0x3200>;
> -			#interconnect-cells = <1>;
> -			qcom,bcm-voters = <&apps_bcm_voter>;
> -		};
> -
> -		gem_noc: interconnect@9680000 {
> -			compatible = "qcom,sm8150-gem-noc";
> -			reg = <0 0x09680000 0 0x3e200>;
> -			#interconnect-cells = <1>;
> -			qcom,bcm-voters = <&apps_bcm_voter>;
> -		};
> -
>  		usb_2_qmpphy: phy@88eb000 {
>  			compatible = "qcom,sm8150-qmp-usb3-uni-phy";
>  			reg = <0 0x088eb000 0 0x200>;
> @@ -2344,7 +2344,7 @@ usb_1: usb@a6f8800 {
>  
>  			resets = <&gcc GCC_USB30_PRIM_BCR>;
>  
> -			usb_1_dwc3: usb@a600000 {
> +			usb_1_dwc3: dwc3@a600000 {

"usb@" is actually the right one, per the rather recent standardization
across the dwc3 bindings.

Regards,
Bjorn

>  				compatible = "snps,dwc3";
>  				reg = <0 0x0a600000 0 0xcd00>;
>  				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
> -- 
> 2.31.1
>