From: Stephan Gerhold <stephan@gerhold.net>
To: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>,
Loic Poulain <loic.poulain@linaro.org>,
Sergey Ryazanov <ryazanov.s.a@gmail.com>,
Johannes Berg <johannes@sipsolutions.net>,
Andy Gross <agross@kernel.org>, Vinod Koul <vkoul@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Aleksander Morgado <aleksander@aleksander.es>,
netdev@vger.kernel.org, linux-arm-msm@vger.kernel.org,
dmaengine@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, phone-devel@vger.kernel.org,
~postmarketos/upstreaming@lists.sr.ht,
Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Subject: Re: [PATCH net-next v2 2/4] dmaengine: qcom: bam_dma: Add "powered remotely" mode
Date: Mon, 11 Oct 2021 20:06:12 +0200 [thread overview]
Message-ID: <YWR9DSp0ry/wprLn@gerhold.net> (raw)
In-Reply-To: <YWR2yN3x3zroz1GX@ripper>
On Mon, Oct 11, 2021 at 10:39:20AM -0700, Bjorn Andersson wrote:
> On Mon 11 Oct 07:17 PDT 2021, Stephan Gerhold wrote:
>
> > In some configurations, the BAM DMA controller is set up by a remote
> > processor and the local processor can simply start making use of it
> > without setting up the BAM. This is already supported using the
> > "qcom,controlled-remotely" property.
> >
> > However, for some reason another possible configuration is that the
> > remote processor is responsible for powering up the BAM, but we are
> > still responsible for initializing it (e.g. resetting it etc).
> >
> > This configuration is quite challenging to handle properly because
> > the power control is handled through separate channels
> > (e.g. device-specific SMSM interrupts / smem-states). Great care
> > must be taken to ensure the BAM registers are not accessed while
> > the BAM is powered off since this results in a bus stall.
> >
> > Attempt to support this configuration with minimal device-specific
> > code in the bam_dma driver by tracking the number of requested
> > channels. Consumers of DMA channels are responsible to only request
> > DMA channels when the BAM was powered on by the remote processor,
> > and to release them before the BAM is powered off.
> >
> > When the first channel is requested the BAM is initialized (reset)
> > and it is also put into reset when the last channel was released.
> >
> > Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
> > ---
> > Changes since RFC:
> > - Drop qcom-specific terminology "power collapse", instead rename
> > "qcom,remote-power-collapse" -> "qcom,powered-remotely"
> >
> > NOTE: This is *not* a compile-time requirement for the BAM-DMUX driver
> > so this could also go through the dmaengine tree.
> >
> > See original RFC for a discussion of alternative approaches to handle
> > this configuration:
> > https://lore.kernel.org/netdev/20210719145317.79692-3-stephan@gerhold.net/
> > ---
> > drivers/dma/qcom/bam_dma.c | 88 ++++++++++++++++++++++++--------------
> > 1 file changed, 56 insertions(+), 32 deletions(-)
> >
> > diff --git a/drivers/dma/qcom/bam_dma.c b/drivers/dma/qcom/bam_dma.c
> > index c8a77b428b52..1b33a3ebbfec 100644
> > --- a/drivers/dma/qcom/bam_dma.c
> > +++ b/drivers/dma/qcom/bam_dma.c
> > @@ -388,6 +388,8 @@ struct bam_device {
> > /* execution environment ID, from DT */
> > u32 ee;
> > bool controlled_remotely;
> > + bool powered_remotely;
> > + u32 active_channels;
> >
> > const struct reg_offset_data *layout;
> >
> > @@ -415,6 +417,44 @@ static inline void __iomem *bam_addr(struct bam_device *bdev, u32 pipe,
> > r.ee_mult * bdev->ee;
> > }
> >
> > +/**
> > + * bam_reset - reset and initialize BAM registers
>
> Please include a set of () after the function name.
>
Thanks, will fix this in v3.
> > + * @bdev: bam device
> > + */
> > +static void bam_reset(struct bam_device *bdev)
> > +{
> > + u32 val;
> > +
> > + /* s/w reset bam */
> > + /* after reset all pipes are disabled and idle */
> > + val = readl_relaxed(bam_addr(bdev, 0, BAM_CTRL));
> > + val |= BAM_SW_RST;
> > + writel_relaxed(val, bam_addr(bdev, 0, BAM_CTRL));
> > + val &= ~BAM_SW_RST;
> > + writel_relaxed(val, bam_addr(bdev, 0, BAM_CTRL));
>
> Seems odd to me that we assert and deassert the reset in back-to-back
> writes, without any delay etc. That said, this is unrelated to your
> patch as you just moved this hunk from below.
>
It seems to work fine though. :)
I'm pretty sure I checked that this actually resets at some point,
but perhaps I was lucky there. But yeah, seems better to adjust this in
some future patch instead of here.
> > +
> > + /* make sure previous stores are visible before enabling BAM */
> > + wmb();
> > +
> > + /* enable bam */
> > + val |= BAM_EN;
> > + writel_relaxed(val, bam_addr(bdev, 0, BAM_CTRL));
> > +
> > + /* set descriptor threshhold, start with 4 bytes */
> > + writel_relaxed(DEFAULT_CNT_THRSHLD,
> > + bam_addr(bdev, 0, BAM_DESC_CNT_TRSHLD));
> > +
> > + /* Enable default set of h/w workarounds, ie all except BAM_FULL_PIPE */
> > + writel_relaxed(BAM_CNFG_BITS_DEFAULT, bam_addr(bdev, 0, BAM_CNFG_BITS));
> > +
> > + /* enable irqs for errors */
> > + writel_relaxed(BAM_ERROR_EN | BAM_HRESP_ERR_EN,
> > + bam_addr(bdev, 0, BAM_IRQ_EN));
> > +
> > + /* unmask global bam interrupt */
> > + writel_relaxed(BAM_IRQ_MSK, bam_addr(bdev, 0, BAM_IRQ_SRCS_MSK_EE));
> > +}
> > +
> > /**
> > * bam_reset_channel - Reset individual BAM DMA channel
> > * @bchan: bam channel
> > @@ -512,6 +552,9 @@ static int bam_alloc_chan(struct dma_chan *chan)
> > return -ENOMEM;
> > }
> >
> > + if (bdev->active_channels++ == 0 && bdev->powered_remotely)
> > + bam_reset(bdev);
> > +
> > return 0;
> > }
> >
> > @@ -565,6 +608,13 @@ static void bam_free_chan(struct dma_chan *chan)
> > /* disable irq */
> > writel_relaxed(0, bam_addr(bdev, bchan->id, BAM_P_IRQ_EN));
> >
> > + if (--bdev->active_channels == 0 && bdev->powered_remotely) {
> > + /* s/w reset bam */
> > + val = readl_relaxed(bam_addr(bdev, 0, BAM_CTRL));
> > + val |= BAM_SW_RST;
> > + writel_relaxed(val, bam_addr(bdev, 0, BAM_CTRL));
> > + }
> > +
> > err:
> > pm_runtime_mark_last_busy(bdev->dev);
> > pm_runtime_put_autosuspend(bdev->dev);
> > @@ -1164,38 +1214,10 @@ static int bam_init(struct bam_device *bdev)
> > bdev->num_channels = val & BAM_NUM_PIPES_MASK;
> > }
> >
> > - if (bdev->controlled_remotely)
> > + if (bdev->controlled_remotely || bdev->powered_remotely)
> > return 0;
>
> I think the resulting code would be cleaner if you flipped it around as:
>
> /* Reset BAM now if fully controlled locally */
> if (!bdev->controlled_remotely && !bdev->powered_remotely)
> bam_reset(bdev);
>
> return 0;
>
Hmm, you are probably right, I can flip it in v3.
Thanks!
Stephan
next prev parent reply other threads:[~2021-10-11 18:06 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-10-11 14:17 [PATCH net-next v2 0/4] net: wwan: Add Qualcomm BAM-DMUX WWAN network driver Stephan Gerhold
2021-10-11 14:17 ` [PATCH net-next v2 1/4] dt-bindings: dmaengine: bam_dma: Add "powered remotely" mode Stephan Gerhold
2021-10-18 6:17 ` Vinod Koul
2021-10-18 10:29 ` Stephan Gerhold
2021-10-18 11:34 ` Bhupesh Sharma
2021-10-18 12:56 ` Stephan Gerhold
2021-10-18 16:41 ` Bhupesh Sharma
2021-10-11 14:17 ` [PATCH net-next v2 2/4] dmaengine: qcom: " Stephan Gerhold
2021-10-11 17:39 ` Bjorn Andersson
2021-10-11 18:06 ` Stephan Gerhold [this message]
2021-10-11 14:17 ` [PATCH net-next v2 3/4] dt-bindings: net: Add schema for Qualcomm BAM-DMUX Stephan Gerhold
2021-10-18 20:22 ` Rob Herring
2021-10-19 7:03 ` Stephan Gerhold
2021-10-19 13:19 ` Rob Herring
2021-10-19 13:31 ` Stephan Gerhold
2021-10-11 14:17 ` [PATCH net-next v2 4/4] net: wwan: Add Qualcomm BAM-DMUX WWAN network driver Stephan Gerhold
2021-10-11 14:51 ` Stephan Gerhold
2021-10-12 7:55 ` Loic Poulain
2021-10-12 8:43 ` Stephan Gerhold
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=YWR9DSp0ry/wprLn@gerhold.net \
--to=stephan@gerhold.net \
--cc=agross@kernel.org \
--cc=aleksander@aleksander.es \
--cc=bjorn.andersson@linaro.org \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=dmaengine@vger.kernel.org \
--cc=jeffrey.l.hugo@gmail.com \
--cc=johannes@sipsolutions.net \
--cc=kuba@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=loic.poulain@linaro.org \
--cc=netdev@vger.kernel.org \
--cc=phone-devel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=ryazanov.s.a@gmail.com \
--cc=vkoul@kernel.org \
--cc=~postmarketos/upstreaming@lists.sr.ht \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).