From: Adam Serbinski <adam@serbinski.com>
To: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Mark Brown <broonie@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Andy Gross <agross@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Liam Girdwood <lgirdwood@gmail.com>,
Patrick Lai <plai@codeaurora.org>,
Banajit Goswami <bgoswami@codeaurora.org>,
Jaroslav Kysela <perex@perex.cz>, Takashi Iwai <tiwai@suse.com>,
alsa-devel@alsa-project.org, linux-arm-msm@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v3 6/6] ASoC: qdsp6: dt-bindings: Add q6afe pcm dt binding documentation
Date: Wed, 12 Feb 2020 07:07:56 -0500 [thread overview]
Message-ID: <d4e16b7944adbd8859c8287673da3417@serbinski.com> (raw)
In-Reply-To: <b5c1328a-e3ca-826d-9ff0-f2bbce24ac22@linaro.org>
On 2020-02-12 06:43, Srinivas Kandagatla wrote:
> On 12/02/2020 11:01, Adam Serbinski wrote:
>>>>
>>>> +
>>>> + - qcom,pcm-slot-mapping
>>>> + Usage: required for pcm interface
>>>
>>> Are these not specific to 8k and 16k mode ?
>>> We should probably list values for both modes here.
>>
>> No, this is just the offset that the audio sample is placed in with
>> respect to a maximum of 4 slots, 16 bits wide, beginning with the sync
>> pulse.
>
>
> That's not true atleast by the QDSP documentation,
> according to it we will use more slots to transfer at higher sample
> rate. ex:
> 16 kHz data can be transferred using 8 kHz samples in two
> slots.
>
> Also there are 32 slots for each of 4 supported channels for PCM AFE
> port.
Ok, if that's the case, then it sounds like someone else is going to
have to implement it. I have no way to test that kind of a
configuration, so attempting to implement it would be futile.
>
>
>>
>> When switching between 8 and 16k sample rate, it is just the sync
>> pulse rate that is changed. The audio sample will be delivered in the
>> same slot, just at a different frequency.
prev parent reply other threads:[~2020-02-12 12:08 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20200212015222.8229-1-adam@serbinski.com>
2020-02-12 1:52 ` [PATCH v3 1/6] ASoC: qdsp6: dt-bindings: Add q6afe pcm dt binding Adam Serbinski
2020-02-12 1:52 ` [PATCH v3 2/6] ASoC: qdsp6: q6afe: add support to pcm ports Adam Serbinski
2020-02-12 1:52 ` [PATCH v3 3/6] ASoC: qdsp6: q6afe-dai: add support to pcm port dais Adam Serbinski
2020-02-12 9:52 ` Srinivas Kandagatla
2020-02-12 9:53 ` Srinivas Kandagatla
2020-02-12 1:52 ` [PATCH v3 4/6] ASoC: qdsp6: q6routing: add pcm port routing Adam Serbinski
2020-02-12 1:52 ` [PATCH v3 5/6] ASoC: qcom: apq8096: add support for primary and quaternary I2S/PCM Adam Serbinski
2020-02-12 1:52 ` [PATCH v3 6/6] ASoC: qdsp6: dt-bindings: Add q6afe pcm dt binding documentation Adam Serbinski
2020-02-12 9:59 ` Srinivas Kandagatla
2020-02-12 11:01 ` Adam Serbinski
2020-02-12 11:43 ` Srinivas Kandagatla
2020-02-12 12:07 ` Adam Serbinski [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=d4e16b7944adbd8859c8287673da3417@serbinski.com \
--to=adam@serbinski.com \
--cc=agross@kernel.org \
--cc=alsa-devel@alsa-project.org \
--cc=bgoswami@codeaurora.org \
--cc=bjorn.andersson@linaro.org \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=lgirdwood@gmail.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=perex@perex.cz \
--cc=plai@codeaurora.org \
--cc=robh+dt@kernel.org \
--cc=srinivas.kandagatla@linaro.org \
--cc=tiwai@suse.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).