* [PATCH 0/2] eliminate two common errors reported by any yaml on arm64 @ 2020-10-13 6:06 Zhen Lei 2020-10-13 6:06 ` [PATCH 1/2] arm64: dts: broadcom: remove an unused property dma-ranges Zhen Lei 2020-10-13 6:06 ` [PATCH 2/2] arm64: dts: qcom: " Zhen Lei 0 siblings, 2 replies; 10+ messages in thread From: Zhen Lei @ 2020-10-13 6:06 UTC (permalink / raw) To: Rob Herring, Ray Jui, Scott Branden, bcm-kernel-feedback-list, Andy Gross, Bjorn Andersson, linux-arm-msm, devicetree, linux-arm-kernel, linux-kernel Cc: Zhen Lei The following errors occured no matter which YAML file I executed on arm64. Therefore, it is necessary to eliminate it so that people's time and energy are not wasted every time. arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but its #address-cells (1) differs from / (2) arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but its #size-cells (1) differs from / (2) arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but its #address-cells (1) differs from / (2) arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but its #size-cells (1) differs from / (2) arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but its #address-cells (1) differs from / (2) arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but its #size-cells (1) differs from / (2) arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but its #address-cells (1) differs from / (2) arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but its #size-cells (1) differs from / (2) arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but its #address-cells (1) differs from / (2) arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but its #size-cells (1) differs from / (2) arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but its #address-cells (1) differs from / (2) arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but its #size-cells (1) differs from / (2) arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning (dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but its #address-cells (1) differs from / (2) arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning (dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but its #size-cells (1) differs from / (2) arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning (dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but its #address-cells (1) differs from / (2) arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning (dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but its #size-cells (1) differs from / (2) Zhen Lei (2): arm64: dts: broadcom: remove an unused property dma-ranges arm64: dts: qcom: remove an unused property dma-ranges arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi | 1 - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 1 - 2 files changed, 2 deletions(-) -- 1.8.3 ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH 1/2] arm64: dts: broadcom: remove an unused property dma-ranges 2020-10-13 6:06 [PATCH 0/2] eliminate two common errors reported by any yaml on arm64 Zhen Lei @ 2020-10-13 6:06 ` Zhen Lei 2020-10-14 3:12 ` Florian Fainelli 2020-10-13 6:06 ` [PATCH 2/2] arm64: dts: qcom: " Zhen Lei 1 sibling, 1 reply; 10+ messages in thread From: Zhen Lei @ 2020-10-13 6:06 UTC (permalink / raw) To: Rob Herring, Ray Jui, Scott Branden, bcm-kernel-feedback-list, Andy Gross, Bjorn Andersson, linux-arm-msm, devicetree, linux-arm-kernel, linux-kernel Cc: Zhen Lei stingray-usb.dtsi is finally included by three dts files: bcm958802a802x.dts, bcm958742k.dts and bcm958742t.dts. I searched all these three entire expanded dts files, and each of them contains only one dma-ranges. No conversion range is specified, so it cannot work properly. I think this property "dma-ranges" is added by mistake, just remove it. Otherwise, the following error will be reported when any YAML detection is performed on arm64. arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ its #address-cells (1) differs from / (2) arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ its #size-cells (1) differs from / (2) Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> --- arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi index 55259f973b5a9e4..9ac8be6c65aa031 100644 --- a/arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi +++ b/arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi @@ -4,7 +4,6 @@ */ usb { compatible = "simple-bus"; - dma-ranges; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0x0 0x68500000 0x00400000>; -- 1.8.3 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH 1/2] arm64: dts: broadcom: remove an unused property dma-ranges 2020-10-13 6:06 ` [PATCH 1/2] arm64: dts: broadcom: remove an unused property dma-ranges Zhen Lei @ 2020-10-14 3:12 ` Florian Fainelli 2020-10-14 7:38 ` Arnd Bergmann 0 siblings, 1 reply; 10+ messages in thread From: Florian Fainelli @ 2020-10-14 3:12 UTC (permalink / raw) To: Zhen Lei, Rob Herring, Ray Jui, Scott Branden, bcm-kernel-feedback-list, Andy Gross, Bjorn Andersson, linux-arm-msm, devicetree, linux-arm-kernel, linux-kernel On 10/12/2020 11:06 PM, Zhen Lei wrote: > stingray-usb.dtsi is finally included by three dts files: > bcm958802a802x.dts, bcm958742k.dts and bcm958742t.dts. I searched all > these three entire expanded dts files, and each of them contains only one > dma-ranges. No conversion range is specified, so it cannot work properly. > I think this property "dma-ranges" is added by mistake, just remove it. > Otherwise, the following error will be reported when any YAML detection > is performed on arm64. > > arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ > (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ > its #address-cells (1) differs from / (2) > arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ > (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ > its #size-cells (1) differs from / (2) > > Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> This looks fine to me, Scott, Ray do you want to Ack this patch before I take it? -- Florian ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/2] arm64: dts: broadcom: remove an unused property dma-ranges 2020-10-14 3:12 ` Florian Fainelli @ 2020-10-14 7:38 ` Arnd Bergmann 2020-10-14 13:36 ` Leizhen (ThunderTown) 0 siblings, 1 reply; 10+ messages in thread From: Arnd Bergmann @ 2020-10-14 7:38 UTC (permalink / raw) To: Florian Fainelli Cc: Zhen Lei, Rob Herring, Ray Jui, Scott Branden, bcm-kernel-feedback-list, Andy Gross, Bjorn Andersson, linux-arm-msm, devicetree, linux-arm-kernel, linux-kernel On Wed, Oct 14, 2020 at 5:15 AM Florian Fainelli <f.fainelli@gmail.com> wrote: > On 10/12/2020 11:06 PM, Zhen Lei wrote: > > stingray-usb.dtsi is finally included by three dts files: > > bcm958802a802x.dts, bcm958742k.dts and bcm958742t.dts. I searched all > > these three entire expanded dts files, and each of them contains only one > > dma-ranges. No conversion range is specified, so it cannot work properly. > > I think this property "dma-ranges" is added by mistake, just remove it. > > Otherwise, the following error will be reported when any YAML detection > > is performed on arm64. > > > > arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ > > (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ > > its #address-cells (1) differs from / (2) > > arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ > > (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ > > its #size-cells (1) differs from / (2) > > > > Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> > > This looks fine to me, Scott, Ray do you want to Ack this patch before I > take it? Does it mean that there are no devices on this bus that can do DMA? Usually there should be a dma-ranges property to identify that DMA is possible and what the limits are, though we have failed to enforce that. Also note that the #address-cells=<1> means that any device under this bus is assumed to only support 32-bit addressing, and DMA will have to go through a slow swiotlb in the absence of an IOMMU. Arnd ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/2] arm64: dts: broadcom: remove an unused property dma-ranges 2020-10-14 7:38 ` Arnd Bergmann @ 2020-10-14 13:36 ` Leizhen (ThunderTown) 2020-10-14 13:43 ` Leizhen (ThunderTown) 2020-10-14 14:02 ` Arnd Bergmann 0 siblings, 2 replies; 10+ messages in thread From: Leizhen (ThunderTown) @ 2020-10-14 13:36 UTC (permalink / raw) To: Arnd Bergmann, Florian Fainelli Cc: Rob Herring, Ray Jui, Scott Branden, bcm-kernel-feedback-list, Andy Gross, Bjorn Andersson, linux-arm-msm, devicetree, linux-arm-kernel, linux-kernel On 2020/10/14 15:38, Arnd Bergmann wrote: > On Wed, Oct 14, 2020 at 5:15 AM Florian Fainelli <f.fainelli@gmail.com> wrote: >> On 10/12/2020 11:06 PM, Zhen Lei wrote: >>> stingray-usb.dtsi is finally included by three dts files: >>> bcm958802a802x.dts, bcm958742k.dts and bcm958742t.dts. I searched all >>> these three entire expanded dts files, and each of them contains only one >>> dma-ranges. No conversion range is specified, so it cannot work properly. >>> I think this property "dma-ranges" is added by mistake, just remove it. >>> Otherwise, the following error will be reported when any YAML detection >>> is performed on arm64. >>> >>> arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ >>> (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ >>> its #address-cells (1) differs from / (2) >>> arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ >>> (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ >>> its #size-cells (1) differs from / (2) >>> >>> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> >> >> This looks fine to me, Scott, Ray do you want to Ack this patch before I >> take it? > > Does it mean that there are no devices on this bus that can do DMA? > > Usually there should be a dma-ranges property to identify that DMA > is possible and what the limits are, though we have failed to enforce > that. Documentation/devicetree/bindings/iommu/iommu.txt +79 When an "iommus" property is specified in a device tree node, the IOMMU will be used for address translation. If a "dma-ranges" property exists in the device's parent node it will be ignored. An exception to this rule is if the referenced IOMMU is disabled, in which case the "dma-ranges" property of the parent shall take effect. The dma-ranges is only required by IOMMU disabled case. And should exist in the parent node of IOMMU device. But this deleted dma-ranges is under the usb bus node. > > Also note that the #address-cells=<1> means that any device under > this bus is assumed to only support 32-bit addressing, and DMA will > have to go through a slow swiotlb in the absence of an IOMMU. The dma_alloc_coherent() will allocate memory with GFP_DMA32 flag and try the 0-4G first. The reserved swiotlb buffer memory is used only when the allocation failed. memory@80000000: device_type: ["memory"] reg: [[0x0, 0x80000000, 0x0, 0x80000000], [0x8, 0x80000000, 0x1, 0x80000000]] If this is the actual physical memory size, the #address-cells should be set to <1>. > > Arnd > > . > ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/2] arm64: dts: broadcom: remove an unused property dma-ranges 2020-10-14 13:36 ` Leizhen (ThunderTown) @ 2020-10-14 13:43 ` Leizhen (ThunderTown) 2020-10-14 14:02 ` Arnd Bergmann 1 sibling, 0 replies; 10+ messages in thread From: Leizhen (ThunderTown) @ 2020-10-14 13:43 UTC (permalink / raw) To: Arnd Bergmann, Florian Fainelli Cc: Rob Herring, Ray Jui, Scott Branden, bcm-kernel-feedback-list, Andy Gross, Bjorn Andersson, linux-arm-msm, devicetree, linux-arm-kernel, linux-kernel On 2020/10/14 21:36, Leizhen (ThunderTown) wrote: > > > On 2020/10/14 15:38, Arnd Bergmann wrote: >> On Wed, Oct 14, 2020 at 5:15 AM Florian Fainelli <f.fainelli@gmail.com> wrote: >>> On 10/12/2020 11:06 PM, Zhen Lei wrote: >>>> stingray-usb.dtsi is finally included by three dts files: >>>> bcm958802a802x.dts, bcm958742k.dts and bcm958742t.dts. I searched all >>>> these three entire expanded dts files, and each of them contains only one >>>> dma-ranges. No conversion range is specified, so it cannot work properly. >>>> I think this property "dma-ranges" is added by mistake, just remove it. >>>> Otherwise, the following error will be reported when any YAML detection >>>> is performed on arm64. >>>> >>>> arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ >>>> (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ >>>> its #address-cells (1) differs from / (2) >>>> arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ >>>> (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ >>>> its #size-cells (1) differs from / (2) >>>> >>>> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> >>> >>> This looks fine to me, Scott, Ray do you want to Ack this patch before I >>> take it? >> >> Does it mean that there are no devices on this bus that can do DMA? >> >> Usually there should be a dma-ranges property to identify that DMA >> is possible and what the limits are, though we have failed to enforce >> that. > > Documentation/devicetree/bindings/iommu/iommu.txt +79 > When an "iommus" property is specified in a device tree node, the IOMMU will > be used for address translation. If a "dma-ranges" property exists in the > device's parent node it will be ignored. An exception to this rule is if the > referenced IOMMU is disabled, in which case the "dma-ranges" property of the > parent shall take effect. > > The dma-ranges is only required by IOMMU disabled case. And should exist in > the parent node of IOMMU device. But this deleted dma-ranges is under the usb > bus node. > >> >> Also note that the #address-cells=<1> means that any device under >> this bus is assumed to only support 32-bit addressing, and DMA will >> have to go through a slow swiotlb in the absence of an IOMMU. > > The dma_alloc_coherent() will allocate memory with GFP_DMA32 flag and > try the 0-4G first. The reserved swiotlb buffer memory is used only > when the allocation failed. ----- Sorry, my mistake, please ignore the following. > > memory@80000000: > device_type: ["memory"] > reg: [[0x0, 0x80000000, 0x0, 0x80000000], [0x8, 0x80000000, 0x1, 0x80000000]] > > If this is the actual physical memory size, the #address-cells should be set to <1>. > >> >> Arnd >> >> . >> ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/2] arm64: dts: broadcom: remove an unused property dma-ranges 2020-10-14 13:36 ` Leizhen (ThunderTown) 2020-10-14 13:43 ` Leizhen (ThunderTown) @ 2020-10-14 14:02 ` Arnd Bergmann 2020-10-16 7:06 ` Leizhen (ThunderTown) 1 sibling, 1 reply; 10+ messages in thread From: Arnd Bergmann @ 2020-10-14 14:02 UTC (permalink / raw) To: Leizhen (ThunderTown) Cc: Florian Fainelli, Rob Herring, Ray Jui, Scott Branden, bcm-kernel-feedback-list, Andy Gross, Bjorn Andersson, linux-arm-msm, devicetree, linux-arm-kernel, linux-kernel On Wed, Oct 14, 2020 at 3:36 PM Leizhen (ThunderTown) <thunder.leizhen@huawei.com> wrote: > On 2020/10/14 15:38, Arnd Bergmann wrote: > > On Wed, Oct 14, 2020 at 5:15 AM Florian Fainelli <f.fainelli@gmail.com> wrote: > >> On 10/12/2020 11:06 PM, Zhen Lei wrote: > >>> stingray-usb.dtsi is finally included by three dts files: > >>> bcm958802a802x.dts, bcm958742k.dts and bcm958742t.dts. I searched all > >>> these three entire expanded dts files, and each of them contains only one > >>> dma-ranges. No conversion range is specified, so it cannot work properly. > >>> I think this property "dma-ranges" is added by mistake, just remove it. > >>> Otherwise, the following error will be reported when any YAML detection > >>> is performed on arm64. > >>> > >>> arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ > >>> (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ > >>> its #address-cells (1) differs from / (2) > >>> arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ > >>> (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ > >>> its #size-cells (1) differs from / (2) > >>> > >>> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> > >> > >> This looks fine to me, Scott, Ray do you want to Ack this patch before I > >> take it? > > > > Does it mean that there are no devices on this bus that can do DMA? > > > > Usually there should be a dma-ranges property to identify that DMA > > is possible and what the limits are, though we have failed to enforce > > that. > > Documentation/devicetree/bindings/iommu/iommu.txt +79 > When an "iommus" property is specified in a device tree node, the IOMMU will > be used for address translation. If a "dma-ranges" property exists in the > device's parent node it will be ignored. An exception to this rule is if the > referenced IOMMU is disabled, in which case the "dma-ranges" property of the > parent shall take effect. > > The dma-ranges is only required by IOMMU disabled case. And should exist in > the parent node of IOMMU device. But this deleted dma-ranges is under the usb > bus node. The USB hosts here don't use an IOMMU though, right? > > Also note that the #address-cells=<1> means that any device under > > this bus is assumed to only support 32-bit addressing, and DMA will > > have to go through a slow swiotlb in the absence of an IOMMU. > > The dma_alloc_coherent() will allocate memory with GFP_DMA32 flag and > try the 0-4G first. The reserved swiotlb buffer memory is used only > when the allocation failed. The swiotlb is primarily about the streaming mappings with dma_map_*(), which has to copy all data sent to the device. dma_alloc_coherent() is a rare operation and less impacted by DMA limitations. Arnd ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/2] arm64: dts: broadcom: remove an unused property dma-ranges 2020-10-14 14:02 ` Arnd Bergmann @ 2020-10-16 7:06 ` Leizhen (ThunderTown) 2020-10-16 7:53 ` Leizhen (ThunderTown) 0 siblings, 1 reply; 10+ messages in thread From: Leizhen (ThunderTown) @ 2020-10-16 7:06 UTC (permalink / raw) To: Arnd Bergmann Cc: devicetree, Florian Fainelli, Scott Branden, Ray Jui, linux-kernel, Rob Herring, Bjorn Andersson, Andy Gross, bcm-kernel-feedback-list, linux-arm-msm, linux-arm-kernel On 2020/10/14 22:02, Arnd Bergmann wrote: > On Wed, Oct 14, 2020 at 3:36 PM Leizhen (ThunderTown) > <thunder.leizhen@huawei.com> wrote: >> On 2020/10/14 15:38, Arnd Bergmann wrote: >>> On Wed, Oct 14, 2020 at 5:15 AM Florian Fainelli <f.fainelli@gmail.com> wrote: >>>> On 10/12/2020 11:06 PM, Zhen Lei wrote: >>>>> stingray-usb.dtsi is finally included by three dts files: >>>>> bcm958802a802x.dts, bcm958742k.dts and bcm958742t.dts. I searched all >>>>> these three entire expanded dts files, and each of them contains only one >>>>> dma-ranges. No conversion range is specified, so it cannot work properly. >>>>> I think this property "dma-ranges" is added by mistake, just remove it. >>>>> Otherwise, the following error will be reported when any YAML detection >>>>> is performed on arm64. >>>>> >>>>> arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ >>>>> (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ >>>>> its #address-cells (1) differs from / (2) >>>>> arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ >>>>> (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ >>>>> its #size-cells (1) differs from / (2) >>>>> >>>>> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> >>>> >>>> This looks fine to me, Scott, Ray do you want to Ack this patch before I >>>> take it? >>> >>> Does it mean that there are no devices on this bus that can do DMA? >>> >>> Usually there should be a dma-ranges property to identify that DMA >>> is possible and what the limits are, though we have failed to enforce >>> that. >> >> Documentation/devicetree/bindings/iommu/iommu.txt +79 >> When an "iommus" property is specified in a device tree node, the IOMMU will >> be used for address translation. If a "dma-ranges" property exists in the >> device's parent node it will be ignored. An exception to this rule is if the >> referenced IOMMU is disabled, in which case the "dma-ranges" property of the >> parent shall take effect. >> >> The dma-ranges is only required by IOMMU disabled case. And should exist in >> the parent node of IOMMU device. But this deleted dma-ranges is under the usb >> bus node. > > The USB hosts here don't use an IOMMU though, right? Generally, USB devices are accessed through the IOMMU. However, even in this case, dma-ranges is not necessarily required. There are many examples of this in arch/arm64/boot/dts/. For example: arch/arm64/boot/dts/arm/juno.dt.yaml. Not sure, but maybe I found the answer. vi drivers/of/address.c +457 457 Thus we treat the absence of 458 * "ranges" as equivalent to an empty "ranges" property which means 459 * a 1:1 translation at that level. 466 * This quirk also applies for 'dma-ranges' which frequently exist in 467 * child nodes without 'dma-ranges' in the parent nodes. --RobH 475 if (ranges == NULL || rlen == 0) { 476 offset = of_read_number(addr, na); 477 memset(addr, 0, pna * 4); 478 pr_debug("empty ranges; 1:1 translation\n"); 479 goto finish; 480 } By the way: At first, I thought that these errors was detected by YAML. Now, I found that it was generated by "make dtbs". That's why it was reported by any YAML. Thus, the need to fix these errors is even more urgent. > >>> Also note that the #address-cells=<1> means that any device under >>> this bus is assumed to only support 32-bit addressing, and DMA will >>> have to go through a slow swiotlb in the absence of an IOMMU. >> >> The dma_alloc_coherent() will allocate memory with GFP_DMA32 flag and >> try the 0-4G first. The reserved swiotlb buffer memory is used only >> when the allocation failed. > > The swiotlb is primarily about the streaming mappings with dma_map_*(), > which has to copy all data sent to the device. dma_alloc_coherent() > is a rare operation and less impacted by DMA limitations. OK, I got it. > > Arnd > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel > > . > ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/2] arm64: dts: broadcom: remove an unused property dma-ranges 2020-10-16 7:06 ` Leizhen (ThunderTown) @ 2020-10-16 7:53 ` Leizhen (ThunderTown) 0 siblings, 0 replies; 10+ messages in thread From: Leizhen (ThunderTown) @ 2020-10-16 7:53 UTC (permalink / raw) To: Arnd Bergmann Cc: devicetree, Florian Fainelli, Scott Branden, Ray Jui, linux-kernel, Bjorn Andersson, Rob Herring, bcm-kernel-feedback-list, Andy Gross, linux-arm-msm, linux-arm-kernel On 2020/10/16 15:06, Leizhen (ThunderTown) wrote: > > > On 2020/10/14 22:02, Arnd Bergmann wrote: >> On Wed, Oct 14, 2020 at 3:36 PM Leizhen (ThunderTown) >> <thunder.leizhen@huawei.com> wrote: >>> On 2020/10/14 15:38, Arnd Bergmann wrote: >>>> On Wed, Oct 14, 2020 at 5:15 AM Florian Fainelli <f.fainelli@gmail.com> wrote: >>>>> On 10/12/2020 11:06 PM, Zhen Lei wrote: >>>>>> stingray-usb.dtsi is finally included by three dts files: >>>>>> bcm958802a802x.dts, bcm958742k.dts and bcm958742t.dts. I searched all >>>>>> these three entire expanded dts files, and each of them contains only one >>>>>> dma-ranges. No conversion range is specified, so it cannot work properly. >>>>>> I think this property "dma-ranges" is added by mistake, just remove it. >>>>>> Otherwise, the following error will be reported when any YAML detection >>>>>> is performed on arm64. >>>>>> >>>>>> arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ >>>>>> (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ >>>>>> its #address-cells (1) differs from / (2) >>>>>> arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ >>>>>> (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ >>>>>> its #size-cells (1) differs from / (2) >>>>>> >>>>>> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> >>>>> >>>>> This looks fine to me, Scott, Ray do you want to Ack this patch before I >>>>> take it? >>>> >>>> Does it mean that there are no devices on this bus that can do DMA? >>>> >>>> Usually there should be a dma-ranges property to identify that DMA >>>> is possible and what the limits are, though we have failed to enforce >>>> that. >>> >>> Documentation/devicetree/bindings/iommu/iommu.txt +79 >>> When an "iommus" property is specified in a device tree node, the IOMMU will >>> be used for address translation. If a "dma-ranges" property exists in the >>> device's parent node it will be ignored. An exception to this rule is if the >>> referenced IOMMU is disabled, in which case the "dma-ranges" property of the >>> parent shall take effect. >>> >>> The dma-ranges is only required by IOMMU disabled case. And should exist in >>> the parent node of IOMMU device. But this deleted dma-ranges is under the usb >>> bus node. >> >> The USB hosts here don't use an IOMMU though, right? > > Generally, USB devices are accessed through the IOMMU. However, even in this > case, dma-ranges is not necessarily required. There are many examples of this > in arch/arm64/boot/dts/. For example: arch/arm64/boot/dts/arm/juno.dt.yaml. > > Not sure, but maybe I found the answer. > > vi drivers/of/address.c +457 > 457 Thus we treat the absence of > 458 * "ranges" as equivalent to an empty "ranges" property which means > 459 * a 1:1 translation at that level. > > 466 * This quirk also applies for 'dma-ranges' which frequently exist in > 467 * child nodes without 'dma-ranges' in the parent nodes. --RobH > > 475 if (ranges == NULL || rlen == 0) { > 476 offset = of_read_number(addr, na); > 477 memset(addr, 0, pna * 4); > 478 pr_debug("empty ranges; 1:1 translation\n"); > 479 goto finish; > 480 } > > By the way: At first, I thought that these errors was detected by YAML. Now, > I found that it was generated by "make dtbs". That's why it was reported by > any YAML. Thus, the need to fix these errors is even more urgent. > > >> >>>> Also note that the #address-cells=<1> means that any device under >>>> this bus is assumed to only support 32-bit addressing, and DMA will Hi, Arnd: I known what you mean now. I will rewrite the patch. Thanks. >>>> have to go through a slow swiotlb in the absence of an IOMMU. >>> >>> The dma_alloc_coherent() will allocate memory with GFP_DMA32 flag and >>> try the 0-4G first. The reserved swiotlb buffer memory is used only >>> when the allocation failed. >> >> The swiotlb is primarily about the streaming mappings with dma_map_*(), >> which has to copy all data sent to the device. dma_alloc_coherent() >> is a rare operation and less impacted by DMA limitations. > > OK, I got it. > >> >> Arnd >> >> _______________________________________________ >> linux-arm-kernel mailing list >> linux-arm-kernel@lists.infradead.org >> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel >> >> . >> > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel > > . > ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH 2/2] arm64: dts: qcom: remove an unused property dma-ranges 2020-10-13 6:06 [PATCH 0/2] eliminate two common errors reported by any yaml on arm64 Zhen Lei 2020-10-13 6:06 ` [PATCH 1/2] arm64: dts: broadcom: remove an unused property dma-ranges Zhen Lei @ 2020-10-13 6:06 ` Zhen Lei 1 sibling, 0 replies; 10+ messages in thread From: Zhen Lei @ 2020-10-13 6:06 UTC (permalink / raw) To: Rob Herring, Ray Jui, Scott Branden, bcm-kernel-feedback-list, Andy Gross, Bjorn Andersson, linux-arm-msm, devicetree, linux-arm-kernel, linux-kernel Cc: Zhen Lei ipq6018.dtsi is only included by ipq6018-cp01-c1.dts. I searched the entire expanded ipq6018-cp01-c1.dts file, and only one dma-ranges was defined. No conversion range is specified, so it cannot work properly. I think this property "dma-ranges" is added by mistake, just remove it. Otherwise, the following error will be reported when any YAML detection is performed on arm64. arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning \ (dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but \ its #address-cells (1) differs from / (2) arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning \ (dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but \ its #size-cells (1) differs from / (2) Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> --- arch/arm64/boot/dts/qcom/ipq6018.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi index a94dac76bf3fbdd..ec88c0723fb512d 100644 --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi @@ -182,7 +182,6 @@ #address-cells = <1>; #size-cells = <1>; ranges = <0 0 0 0xffffffff>; - dma-ranges; compatible = "simple-bus"; prng: qrng@e1000 { -- 1.8.3 ^ permalink raw reply related [flat|nested] 10+ messages in thread
end of thread, other threads:[~2020-10-16 7:53 UTC | newest] Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2020-10-13 6:06 [PATCH 0/2] eliminate two common errors reported by any yaml on arm64 Zhen Lei 2020-10-13 6:06 ` [PATCH 1/2] arm64: dts: broadcom: remove an unused property dma-ranges Zhen Lei 2020-10-14 3:12 ` Florian Fainelli 2020-10-14 7:38 ` Arnd Bergmann 2020-10-14 13:36 ` Leizhen (ThunderTown) 2020-10-14 13:43 ` Leizhen (ThunderTown) 2020-10-14 14:02 ` Arnd Bergmann 2020-10-16 7:06 ` Leizhen (ThunderTown) 2020-10-16 7:53 ` Leizhen (ThunderTown) 2020-10-13 6:06 ` [PATCH 2/2] arm64: dts: qcom: " Zhen Lei
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).